Eve Audio | SC407 | Product manual | Eve Audio SC407 Product manual

EVE AUDIO PRODUCT MANUAL
AUG 2013
SC407
SC408
SC407
SC408
EVE Audio product manual
SAFETY INSTRUCTIONS
TABLE OF CONTENTS
To avoid the risk of electrical shock, do not attempt to open the unit.
There are no user-serviceable parts inside. Do not attempt to service the
equipment yourself. In case of problems, please contact your local dealer
or distributor.
1.INTRODUCTION.............................................................................4
!
This unit should be connected to a grounded power outlet. If you use
extension cords and power distributors they should be grounded as well.
!
Verify that the specified operating voltage on the rear side matches the
local mains voltage. If these values do not match you will have to adjust
the loudspeaker setting appropriately and change the fuse type.
Use only the fuse types specified on the rear side of the unit. Never bypass
the fuse.
Make sure that no liquids wet the inside of the cabinet. Never spray, pour
or spill liquids directly onto the unit.
Do not use a wet cloth nor flammable or acid chemicals for cleaning.
!
Do not touch the diaphragms of the loudspeaker and do not obstruct the
bass reflex ports.
!
Make sure there is enough air flow behind the loudspeaker to maintain the
electronic components cool.
!
Do not expose this product to extreme temperatures.
The diaphragms build up a magnetic field around the loudspeaker.
High sound pressure levels can damage your hearing permanently! Avoid
standing close to loudspeakers producing high sound pressure levels.
2.
QUICK START..................................................................................5
2.1.
2.2.
2.3.
First Steps..............................................................................................................................5
Speaker Connection..........................................................................................................5
Powering On........................................................................................................................5
3.OPERATION....................................................................................6
3.1. First Steps..............................................................................................................................6
3.2. Horizontal/Vertical Orientation.....................................................................................7
3.3. The Grid.................................................................................................................................8
3.4. Operating Modes...............................................................................................................8
3.5. Powering on/off: Standby Mode..................................................................................8
3.6. Volume Mode......................................................................................................................9
3.7. Settings Menu.................................................................................................................. 10
3.8.Filter..................................................................................................................................... 10
3.9. Low Filter............................................................................................................................ 11
3.10. High Filter.......................................................................................................................... 11
3.11. Low and High Filter Combinations........................................................................... 12
3.12. Desk Filter.......................................................................................................................... 12
3.13. LED Mode........................................................................................................................... 13
3.14. Saving Your Settings...................................................................................................... 13
3.15. Power Switch.................................................................................................................... 13
3.16. DIP Switches...................................................................................................................... 14
3.17. Mains Voltage Selector.................................................................................................. 14
3.18. Power Connector (IEC).................................................................................................. 15
4.POSITIONING...............................................................................15
4.1.
4.2.
4.3.
4.4.
4.5.
4.6.
4.7.
Speaker Positioning + Rubber Feet.......................................................................... 15
Height and Distance...................................................................................................... 16
Stereo Setup..................................................................................................................... 17
Stereo Setup + Subwoofer (2.1)................................................................................. 17
Multichannel Setup (5.1).............................................................................................. 18
Mixer/Workplace Reflections...................................................................................... 19
Room Acoustics............................................................................................................... 19
5.
TECHNICAL SPECIFICATIONS......................................................21
6.COMPLIANCE................................................................................22
7.WARRANTY...................................................................................23
2




3
SC407
SC408
EVE Audio product manual
1. INTRODUCTION
2. QUICK START
Thank you for your time and interest in the EVE Audio product range.
EVE Audio is a loudspeaker manufacturer based in Berlin, Germany, that
specializes in the development and design of unique studio monitors.
The use of first-class components is our highest priority because we firmly
believe this is the only way to manufacture first-class products.
You have chosen a loudspeaker from our Silvercone SC series. Both models
— SC407 and SC408 — were conceived as four-way systems.
An additional mid-range driver guarantees an excellent definition in the
mid frequencies, which raises the four-way system to a completely different
listening level. The two woofers reproduce the exact same frequency
range, while the mid-range driver and tweeter cover consecutive ranges.
Due to this design, the SC407/SC408 are symmetrically mirrored.
In a horizontal arrangement, the SC40X is ideal as fully symmetrical central
loudspeaker.
Both models feature EVE Audio‘s Air Motion Transformer taken from
the RS series. The mid-range driver and the two woofers sport a highquality chassis developed by EVE Audio. The lot is completed by the
implementation of high-resolution DSP technology plus powerful and
efficient amplifiers.
We wish you a lot of fun with your EVE Audio monitors. If you have any
questions regarding our products, do not hesitate to contact your nearest
dealer or get directly in touch with us... We will be more than happy to help
you out!
All the best from Berlin.
The EVE Audio Team
4
INTRODUCTION

If you already have experience with studio monitors, the Quick Start guide
ought to be more than enough to get you started.
For unexperienced users we recommend reading the whole user‘s manual
in order to prevent any misuse.
2.1. First Steps
Check the package components (loudspeaker, user‘s manual, power cord,
grille, rubber feet).
Check the voltage setting (see „Mains Voltage Selector“).
Check the setting of the DIP Switches (variable).
2.2. Speaker Connection
Connect one of the monitor inputs on the rear side (RCA or XLR) to the line
output of a playback source, for instance, an audio interface. The output
level should be as low as possible.
2.3. Powering On
Engage the Power switch on the rear side of the loudspeaker to turn it on
or off.
The LEDs around the Volume control on the front panel will light up
clockwise. If the LED on the right end is dimly lit, this indicates that the
loudspeaker is in Standby mode. Press the Volume control to turn the
loudspeaker on. If you turn the Volume control counter clockwise until the
LED on the left end lights up dimly the loudspeaker will be muted.
Increase the output level on the source device until the LED ring starts to
blink, then reduce the output level a bit. The maximum operating level for
the input (i.e. the analog to digital converter) is now set optimally. To set
the desired listening volume use the Volume control on the loudspeaker.
The LED ring indicates the volume setting. If the LED ring starts to blink,
reduce the output level on the signal source.
QUICK START
Powering On
5
SC407
SC408
EVE Audio product manual
3. OPERATION
3.2. Horizontal/Vertical Orientation
The SC407 and SC408 can be used in horizontal or vertical position thanks
to the incorporated swiveling „Mid/High Silver Plate.“ By default, your
monitor is adjusted to be placed horizontally. To use it in vertical position,
turn the tweeter/mid-driver section 90º so that the sound transducer is
vertically oriented. Your dealer will be happy to this for you. If you would
like to do it by yourself after the monitors have been installed, follow these
steps:
••
Remove the four screws of the mid/high plate.
••
Turn the whole tweeter/mid-driver section 90º. The direction does not
really matter. Hold the tweeter/mid-driver section by the screws when
handling it.
••
Fasten the tweeter/mid-driver section again with the screws. Tighten the
screws only a bit tighter than you would by hand.
3.1. First Steps
1
3
Rear Connections & DIP Switches
••
••
6
Check the package components (loudspeaker, user‘s manual, power cord,
grille, rubber feet);
Check the voltage setting (see „Mains Voltage Selector“).
Check the setting of the DIP Switches (variable).
Connections: there are two input connectors on the rear side. These allow
the connection of balanced sources with XLR connectors or unbalanced
sources with RCA connectors.
Pin assignment XLR: 1 = Shield, 2 = hot (+), 3 = cold(-).
Pin assignment RCA: Center conductor = Signal, Ring = Shield.
Both analog inputs can be used simultaneously, whereby the signals are
summed.
Depending on the setting of the Max. Input DIP switch on the rear panel,
the maximum level of the source signal should not exceed +7 dBu or +22
dBu (see Max. Input). If the input is overloaded the LED ring will start
blinking.
OPERATION
First Steps
2
!!
The whole procedure ought to be carried out with utmost care in order not
to damage the surface of the speaker.
!!
To avoid damages due to metal parts ending up inside the twitter, we
recommend you to place the protection grille immediately after any
modification.
OPERATION
Horizontal/Vertical Orientation
7
SC407
SC408
EVE Audio product manual
3.3. The Grid
In order to protect the tweeter, your EVE Audio monitors are supplied with
a metal grid, which has no impact on the sound. The grid is attached to the
tweeter by means of magnetic attraction.
Be careful not to damage the folded tweeter diaphragm when placing the
grid:
Wrong grid position < > Right grid position
Hold the grille with your fingers parallel to the front side of the monitor.
The perforated hexagon must exhibit two horizontal sides. Make sure that
the grille remains parallel to the front side.
Draw the grille close to the tweeter. The tweeter‘s magnetic field will attract
and fix the grille, which can always be adjusted later if needed.
!!
Standby mode. The volume will decrease gradually while the LED ring
lights up once around the Volume control. Afterwards, the LED on the right
end will remain dimly lit and the power consumption is reduced to 1 watt.
To exit the Standby mode press briefly the Volume control once again. The
level will increase gradually.
3.6. Volume Mode
••
Level Adjustment
The maximum input level for balanced (XLR) and unbalanced signals (RCA)
is +7 dBu or +22 dBu, depending on the position of the Max. Input switch
on the rear panel (see DIP Switches). Higher levels produce distortion due
to the overloading of the analog to digital converter.
Given that some professional studio devices can produce in excess of
+22 dBu, the LED ring will start blinking whenever the AD converter is
overloading. If that is the case, the output level of the source should be
reduced.
••
Volume Adjustment
-20 dB
1 Step = 0.5 dB
(1 LED = 4 Steps)
1 Step = 1 dB
(1 LED = 4 steps)
-12 dB
1 Step = 0.5 dB
(1 LED = 2 Steps)
3.4. Operating Modes
-8 dB
-48 dB
1 Step = 0.5 dB
(1 LED = 4 Steps)
1 Step = 2 dB
(1 LED = 4 Steps)
Standby mode | Volume mode (-10 dB) | Settings menu (Low Filter @ -2 dB)
3.5. Powering on/off: Standby Mode
Press and hold the control three seconds in order to put the monitor in
8
OPERATION
Powering on/off: Standby Mode
-80 dB
0 dB
Turn the knob to adjust the volume. Depending on the LED mode selected
(see LED mode), the volume will be displayed as a dim/bright circle or as a
dim/bright point.
OPERATION
Volume Mode
9
SC407
SC408
EVE Audio product manual
The control’s response curve is not linear. The increments become finer as
the volume increases:
-80 dB (minimum) to -48 dB:
2 dB
-48 dB to -20 dB:
1 dB
-20 dB to 0 dB (maximum):
0.5 dB
••
!!
Mute
To mute the monitor, turn the Volume control counter clockwise until you
reach the minimum level. When the LED on the left end lights up dimly the
Mute mode is activated.
To exit the Mute mode simply turn the control clockwise until you reach
the desired volume.
3.7. Settings Menu
Press the control once to enter the Settings menu. Here you can set three
different filters (Low, Desk, High), as well as the LED ring‘s behavior. The
LED of the currently active function will blink.
Turn the control to choose the filter or LED mode desired. The blinking
LED indicates the function selected, while the steady-on LED indicates the
value assigned to that function.
Press the control to confirm your selection. The blinking will stop once the
selection is confirmed.
Turn the control to adjust the filter or the LED behavior.
When you are satisfied with the setting, press the control again to go back
to the Settings menu. You can then select and edit another function.
!!
To exit the Settings menu press and hold the control for three seconds or
simply wait 10 seconds. The loudspeaker will then return automatically to
the Volume mode.
3.8. Filter
The filters of the EVE Audio monitors were specially developed to offer you
the possibility of adjusting your monitoring system to the characteristics
of your room. These filters help correct the alterations to the frequency
response produced by the room acoustics and listening distance. Do bear
in mind that correcting bad room acoustics with filters will only achieve
average results. In any case, you should try to use the filters as little as
possible.
10
OPERATION
Filter
3.9. Low Filter
dB
+5
+3
0
Hz
-3
-5
100
1k
10k
The Low-Shelf Filter allows you to boost or attenuate frequencies below
300 Hz in 0.5 dB steps. Use this filter whenever the acoustics of your room
cause problems in the low frequency range.
If the low frequencies are boosted by the room, you can attenuate them
with the Low-Shelf Filter. The reasons for this boost could be the room
modes or the loudspeakers being too close to the walls. In the same way,
if the low frequencies are too weak, you can boost them to balance the
frequency response.
3.10. High Filter
dB
+5
+3
0
Hz
-3
-5
100
1k
10k
The High-Shelf Filter allows you to boost or attenuate frequencies above
3 kHz in 0.5 dB steps. High frequencies are affected depending on the
distance from the sound source to the listening position. The further you
are from the loudspeakers, the weaker the high frequencies. In such cases
the filter should be set to boost them. In desktop applications, distances
can be as short as 1 m (3 ft), which results in the high frequencies being
boosted. To compensate for this effect you should use the High-Shelf Filter
to attenuate the high frequencies.
If you have a very dead room, it might be wise to boost the high frequencies
in order to have a more balanced overall sound. When the listening position
OPERATION
High Filter
11
SC407
SC408
EVE Audio product manual
is too close to the loudspeakers or the room has reflective surfaces, it is
reasonable to attenuate the high frequencies.
3.11. Low and High Filter Combinations
the filter gain.
When turned up, the Desk Filter also works as an EQ but this time set to 80
Hz. This allows you to give more punch to the lower frequencies.
!!
dB
+5
+3
0
Hz
3.13. LED Mode
The LED mode determines in which of the four available fashions the LED
ring displays the volume level. The LEDs represent given levels, which are
displayed and adjusted according to four steps. Intermediate steps are
indicated by the brightness between two adjacent LEDs.
-3
-5
100
1k
10k
Attenuating the mids by boosting the high and low frequencies.
dB
+5
••
Bright Ring
All LEDs up to the selected volume level light up brightly. The louder the
signal, the longer the brightly lit-up ring.
••
Bright Point
Only the LEDs corresponding to the selected volume level light up brightly.
The louder the signal, the further up the brightly lit-up point moves.
••
Dimly Lit Ring
All LEDs up to the selected volume level light up dimly. The louder the
signal, the longer the dimly lit-up ring. In this mode, the LEDs light up
brightly momentarily while you adjust the volume level.
••
Dimly Lit Point
Only the LEDs corresponding to the selected volume level light up dimly.
The louder the signal, the further up the dimly lit-up point moves.
!!
Intermediate steps are indicated by the lighting of two adjacent LEDs. The
level ranges from -60 dB to +10 dB, taking „0 dB“ as reference point.
+3
0
Hz
-3
-5
100
1k
10k
Boosting the mids by attenuating the high and low frequencies.
3.12. Desk Filter
dB
+5
+3
0
Hz
-3
-5
100
1k
10k
The Desk Filter has two functions. When turned down it acts as a narrowband EQ set to 160 Hz (SC407 and SC408).
The reflections of mixers and similar surfaces usually result in the boosting
of low mids. With the Desk Filter you can lessen this effect by turning down
12
OPERATION
Desk Filter
The following applies to all three filters:
• Every step represents a 0.5 dB increment.
• Maximal boost is +3 dB and maximal attenuation is –5 dB.
• Refer to the chapter on POSITIONING to set the filters of your EVE Audio
monitors effectively.
3.14. Saving Your Settings
All settings on the front and rear panels are automatically saved. The
loudspeakers can be disconnected anytime without the settings being
lost.
3.15. Power Switch
The power switch on the rear panel disconnects the loudspeaker
OPERATION
Power Switch
13
SC407
SC408
EVE Audio product manual
completely from the power grid. When powered off all settings are saved
and the power consumption is reduced to 0 watts.
After powering on again, the loudspeaker will return to the state it was
in before being turned off (Standby mode, Mute mode or a given volume
level). Even if powered off via a multiple outlet power strip, the monitor will
return to the state it was in before being turned off.
!!
In order to prevent switching noise with your monitoring system, keep in
mind the following rules:
Power all audio sources on first and your loudspeakers last.
When turning off your system, power off your loudspeakers first and then
all audio sources.
3.16. DIP Switches
On the rear panel of your EVE Audio monitors you will find three DIP
Switches. These allow you to secure your loudspeaker settings to prevent
them from being changed inadvertently.
••
Volume
When set to “lock,” this DIP Switch secures the current volume setting. The
LED ring on the front panel indicates the volume setting, but it cannot be
modified. When set to “variable,” the volume setting can be changed by
simply turning the knob.
••
Filter
When set to “lock,” this DIP Switch secures the current filter settings. The
filter settings can be read on the LED ring, but they cannot be modified.
When set to “variable,” the filters can be modified freely.
••
Not used
No Function.
••
Max. Input
This DIP Switch determines the input sensitivity of the SC407 and SC408.
In a studio environment, the reference level (0dB) ought to be 4dBu. In
such environments, leave the setting at “+7dBu.” However, some studio
gear allow much higher output levels. If it were impossible to reduce the
output level of such devices, set the switch to “+22dBu.”
The “+7dBu” setting ought to be suitable for most situations.
3.17. Mains Voltage Selector
The Mains Voltage Selector allows you to adjust the operating voltage of
14
OPERATION
Mains Voltage Selector
your EVE Audio monitors to the local power grid. Set it to “230” if your local
power grid is 220-240 volts or “115” if it is 110-120 volts.
If you change the mains voltage value you also have to replace the fuse of
the IEC connector with an appropriate one. The corresponding fuse values
are printed on the unit underneath the IEC connector.
3.18. Power Connector (IEC)
Use the power cord supplied to connect your EVE Audio monitors to the
power grid. The IEC connector includes an integrated fuse. If your EVE
Audio monitors stop working and the fuse seems to be the problem,
proceed as follows:
••
Turn the loudspeaker off.
••
Disconnect it from the power grid.
••
Detach the IEC connector from the unit.
••
Remove the fuse.
••
Change the fuse. The replacement fuse should comply with the values
stated on the subwoofer.
4. POSITIONING
4.1. Speaker Positioning + Rubber Feet
Ideally, there should be no objects or obstacles between the loudspeakers
and the listening position. Furthermore, a symmetrical positioning is
important. This applies to the distance between speakers as well as to the
walls, ceiling and floor. In order to have a symmetrical stereo image it is
also important to have symmetrical reflections. We recommend to keep
a distance of at least 0.5 m (19 inches) to the walls, in order to avoid low
frequency boosting.
EVE Audio monitors can also be flush-mounted in a wall, in which case
there should be enough air flow. This is important to keep the electronic
components cool but also to allow for the best performance of the bass
reflex ports. We recommend to keep at least 3 cm (1 in) to the sides and
top.
The SC407 and SC408 monitors were designed to be placed vertically or
horizontally. The best position in each case will be determined by the room
and the system used. By default, your monitor is adjusted to be placed
horizontally. To use it in vertical position, turn the tweeter/mid-driver
section 90º. Follow the procedure indicated in the “Horizontal/Vertical
POSITIONING
Speaker Positioning + Rubber Feet
15
SC407
SC408
EVE Audio product manual
Orientation” section. Finally, fix the supplied rubber feet to the bottom side
of the monitor and place it on an even and stable surface.
Rubber feet: your EVE Audio monitors are supplied with four self-adhesive
rubber feet. Fix them to the bottom of your loudspeakers to place the
monitors safely on an even surface. Furthermore, the rubber feet improve
the acoustic decoupling of the loudspeakers from the surface.
4.2. Height and Distance
The tweeter of your EVE Audio monitors should be ideally placed at the
same height as your ears. If this is not possible tilt the monitors so that the
tweeter is directed to your ears.
The ideal distance between the monitors and the listening position is
2-3 m (7-10 ft) for the SC407 and 2.5-3.5 m (8-11 ft) for the SC408.
4.3. Stereo Setup
The so-called “stereo triangle” is the best way to place speakers in a
stereo setup, i.e. the monitors and the listening position should form an
equilateral triangle. Try the following:
Establish the ideal distance to the listening position (see “Height &
Distance”).
Place the monitors in such a way that the distance from each other and to
the listening position is the same.
Turn both monitors so that their front panels are pointed towards the
listening position (all angles of the stereo triangle should be 60º).
4.4. Stereo Setup + Subwoofer (2.1)
In such a setup, the subwoofer is fed by the stereo signal source. The
subwoofer filters the low frequency components of the stereo channels
and sums them to produce a mono signal, which it then reproduces. The
high frequencies are forwarded to the full-range satellite speakers.
Ideally, such a system would comprise two EVE Audio SC407 or SC408
monitors plus an EVE Audio TS110 or TS112 subwoofer. These subwoofers
allow you to set the crossover frequency for the satellite loudspeakers and
the subwoofer.
60°
60°
Stereo Setup (left) and Stereo Setup + Subwoofer (right)
!!
16
These values are only meant as a reference and depend a lot on the
characteristics of the room. In live rooms you will be forced to reduce the
distance, while in dead rooms the distance to the loudspeakers can be
larger.
POSITIONING
Height and Distance
The positioning of the two satellites should be done in the same manner as
in a stereo setup (see “Stereo Setup”).
The subwoofer should be placed on the ground between both satellites.
Considering that low frequencies are omnidirectional, the subwoofer does
POSITIONING
Stereo Setup + Subwoofer (2.1)
17
SC407
SC408
EVE Audio product manual
not have to be centered exactly between the two satellites. The subwoofer
can be moved back a bit so that it is at the same distance from the listening
position as the satellites. This guarantees all transducers are aligned in time.
4.5. Multichannel Setup (5.1)
The most common 5.1 systems consist of three front channels (left, right
and center), two surround channels (left/right) and a subwoofer for the
low frequencies. The speakers from a circle around the listening position.
Ideally, a 5.1 system would comprise five EVE Audio SC407 or SC408
monitors plus an EVE Audio TS110 or TS112 subwoofer. However, you
might also want to consider the following combinations: Front: SC407,
Center: SC407, Rear: SC307; or Front: SC408, Center SC408, Rear: SC407.
The positioning of the two front speakers and the subwoofer should be
done in the same manner as in a stereo setup with a subwoofer (see “Stereo
Setup + Subwoofer“).
Place the center monitor directly in front of the listening position, i.e. right
in the center between both front satellites.
The rear satellites should form an isosceles triangle with the listening
position forming an angle of 140º.
Verify that all speakers are at the same distance from the listening position,
so that they are aligned in time.
4.6. Mixer/Workplace Reflections
Regardless of whether the monitors are to be used in a recording studio
with a mixing desk and meter bridge or in a desktop environment,
hard surfaces can produce annoying reflections that alter the natural
reproduction of the loudspeakers. Especially in the low-mid frequency
range.
60°
80°
140°
If this is the case with your setup, use the Desk Filter of your EVE Audio
monitors to reduce the impact of the reflections from the desk or mixer.
4.7. Room Acoustics
In order for the described measures to work effectively, we recommend
that you put special attention to the room acoustics. The size, contents,
wall parallelism, proportion, and reflective behavior of the room, as well
as the corners, the building materials and their characteristics play a very
important role in the acoustics of a room.
18
POSITIONING
Multichannel Setup (5.1)
POSITIONING
Room Acoustics
19
SC407
SC408
••
••
••
••
••
••
20
EVE Audio product manual
Room acoustics is a science in itself and it is unfortunately out of the scope
of this manual. However, we have put together a short bibliography for
you:
“Recording Studio Design” by Philip Newell. ISBN: 0-240-51917-5
“Home Recording Studio – Build it like the Pros” by Rod Gervais. ISBN:
1-59863-034-2
“Studio Akustik” (in German) by Andreas Friesecke. ISBN: 978-3-932275-81-4
“Praktische Raumakustik” (in German) by Thomas Hentschel. ISBN 978-38364-6800-8
“Handbuch der Tonstudiotechnik” Book 1 (in German) by Michael Dickreiter.
ISBN 3-598-11321-8
“Handbuch der Audiotechnik” (in German) by Stefan Weinzierl (Ed). ISBN
978-3-540-34300-4
POSITIONING
Room Acoustics
5. TECHNICAL SPECIFICATIONS
Product
Description
Dimensions (WxHxD) (mm)
Dimensions (WxHxD) (“)
Frequency Range (-3dB)
Tweeter
Woofer
Mid-Low Driver
Crossover Frequencies
Maximum SPL @ 1m
Number of Amplifiers
Total Output Power (short term)
Output Power (woofer)
Output Power (Mid Driver)
Output Power (tweeter)
Limiter
Setting Options
Volume
High-Shelf Filter (-5db – +3dB)
Desk Filter Boost (0db – +3dB)
Desk Filter Cut (-5db – 0dB)
Low-Shelf Filter (-5db – +3dB)
Volume Lock
Filter Lock
Input Level Switch
Connections
XLR Input (impedance)
RCA Input (impedance)
Power Consumption
Standby
Maximum
Miscellaneous
Weight kg / lb.
SC407
SC408
4-way Monitor
4-way Monitor
600 x 260 x 320
710 x 330 x 440
23.62 x 10.24 x 12.6 27.95 x 12.99 x 17.32
35Hz - 21kHz
30Hz - 21kHz
AMT RS3
AMT RS3
2 x 165mm / 6.5”
2 x 200mm / 8”
100mm / 4”
130mm / 5”
280Hz/3,000Hz
250Hz/3,000Hz
116dB
118dB
4
4
600W
800W
2 x 185W
2 x 250W
180W
250W
50W
50W
Yes
Yes
-inf. – +6dB
> 3kHz
80Hz
160Hz
< 300Hz
Yes
Yes
+7dBu / +22dBu
-inf. – +6dB
> 3kHz
80Hz
160Hz
< 300Hz
Yes
Yes
+7dBu / +22dBu
Yes (10kΩ)
Yes (10kΩ)
Yes (10kΩ)
Yes (10kΩ)
< 1W
300VA
< 1W
350VA
18 / 39.7
29.5 / 65
TECHNICAL SPECIFICATIONS
Room Acoustics
21
SC407
SC408
EVE Audio product manual
6. COMPLIANCE
7. WARRANTY
We,
EVE Audio GmbH,
with registered office in
Ernst Augustin Str. 1a, 12489 Berlin, Germany,
herewith declare that the
SC407 und SC408 products
comply with the following norms:
EC Norms:
EN 60065: 2002 + A1:2006 + A11:2008 + A2:2010 + A12:2011
EC Regulation 1275/2008: 2008-12-18
EN 62301: 2005
EMC Norms:
EN 55013: 2001 + A1:2003 + A2:2006
EN 55020: 2007 + A11:2011
EN 61000-3-2: 2006 + A1:2009 + A2:2009
EN 61000-3-3: 2008
This declaration certifies that the quality control and product
documentation complies with the current corresponding EU directives.
▷▷
The manufacturer warranty is valid for a period of two (2) years after the
date of purchase.
▷▷
The warranty covers repair costs (labor and spare parts), product
replacement if applicable, and return transport within the country where
the product was bought.
▷▷
••
••
••
••
••
The warranty will be void if any of the following applies:
Damages have been caused by incorrect installation and/or connection,
Damages have been caused by misuse or negligence,
The unit has been tampered with or modified in any way,
The unit has been repaired or modified by unqualified personnel,
Damages have been caused by factors beyond the reasonable control of
EVE Audio (lightning, fire, flood, etc.)
▷▷
Always keep the original packaging of any EVE Audio product: Only
products with original packaging are eligible for warranty service. If the
product is not packaged in its original box, EVE Audio will not be liable for
any damages occurred during transit.
▷▷
Should service be required during or after the warranty period, please
contact your local EVE Audio dealer or distributor.
Issued in Berlin.
Signature
Roland Stenz
Managing Director EVE Audio
22
COMPLIANCE
Room Acoustics
WARRANTY
Room Acoustics
23
EVE AUDIO PRODUCT MANUAL
EVE AUDIO GmbH
. Ernst Augustin Str. 1a,
12489 Berlin, Germany
@
.
.
.
.
.
.
+49-30-6704 4180
+49-30-6704 4188
i n f o @ e v e - a u d i o. c o m
w w w. e v e - a u d i o. c o m
facebook.com/EveAudio
twitter.com/EveAudio
Aug 2013 © EVE Audio. All rights reserved.
EVE Audio reserves the right to make changes in or additions to the information provided at any time.
Download PDF