BEA | Stanley Dip Switch I | User manual | USERS GUIDE LO-21U LOCKOUT RELAY

Add to My manuals
5 Pages

advertisement

BEA | Stanley Dip Switch I | User manual | USERS GUIDE LO-21U LOCKOUT RELAY | Manualzz

USERS GUIDE

LO-21U

LOCKOUT RELAY

PRODUCT

DESCRIPTION

TECHNICAL

SPECIFICATIONS

The LO-21U (PN: 10LO21U) is a micro-processed lock out module designed to operate on swing door applications with

BEA’s Bodyguard or DK-12 overhead presence sensor. The LO-21U interprets door open or door closed position based upon motor voltage input. The motor voltage information is sent from the LO-21U to the Bodyguard or DK-12 via data lines.

The LO-21U provides optional safety beam input (dry contacts) to override the inhibit signal during closing.

‰ ANSI / BHMA 156.10-2005 requires the use of a sensor or photobeam on the swing side of the door when using a header mounted safety sensor, such as the Bodyguard or DK12. For more information reference the ANSI

156.10 standard.

DESCRIPTION

Supply voltage

Operating frequency

Power consumption

SPECIFICATION

12 to 24 VAC / 15 to 24 VDC

4 MHz (Microprocessor)

10 mA at rest, 50 mA Maximum

Maximum voltage – Relay contacts

Maximum current – Relay contacts

60 VDC, 120 VAC

2A DC, 0.5 A AC

COMPONENT ID

Green LED Dipswitches

Red LED

PRECAUTIONS

!

CAUTION

SAFETY •

Shut off all power going to the header before attempting any wiring procedures.

Maintain a clean & safe environment when working in public areas.

Constantly be aware of pedestrian traffic around the door area.

Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.

Always check placement of all wiring before powering up to insure that moving door parts will not catch any wires and cause damage to equipment.

Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.

75.1041.06 20060605 Page 1 of 5

WIRING

INSTRUCTIONS

1. Wire the LO-21U according to the chart below.

WIRE COLOR CONNECTION POINT

Violet

White

Black / White

Orange

Gray

Red / White

Brown

Green

Blue

Yellow

Bodyguard Pin 3 (Common)

Bodyguard Pin 6 (Data - )

Safety Beam (Common)

Power (-) / 12 to 24 volts AC/DC

Bodyguard Pin 4 (N/O)

Bodyguard Pin 7 (Data +) and Safety Beam (N/O)

Power (+) / 12 to 24 volts AC/DC

Door Control (Common)

Door Control (Activate)

Door Control (Safety)

115 VAC

24 V

TRANSFORMER

SAFETY BEAM

INPUT DRY CONTACTS

APPROACH SIDE

BLACK/WHITE

RED/WHITE

WHITE

ORANGE

BROWN

LO21U

GREEN

YELLOW

BLUE

SAFETY SIDE

DOOR CONTROL

STALL/ STOP-n- HOLD

COMMON

SAFETY

ACTIVATION

DIPSWITCH

SETTINGS

BODYGUARD

DATA + 7

DATA - 6

-

+ MOTOR VOLTAGE

N.C. 5

DK-12

N.O. 4

COM 3

POWER 2

POWER 1

MOTOR

EAGLE

1. The dipswitches are located at the end of the LO-21U, opposite of the wire connection terminal. There are 8 positions available. Dipswitch designations are as follows:

OFF

Default settings shown.

1 2 3 4 5 6 7 8 ON

6

7

8

Dipswitch #

1

2

3

4

5

75.1041.06 20060605

Function

Time Delay: 1 sec. value

Time Delay: 2 sec. value

Time Delay: 4 sec. value

Time Delay: 8 sec. value

Time Delay: 16 sec. value

OFF

0 seconds

0 seconds

0 seconds

0 seconds

0 seconds

Voltage switching device Voltage source is other than motor

Safety circuit logic (used with DS #8) 7 OFF / 8 ON = N/O Safety Circuit

Safety circuit logic (used with DS #7) 7 ON / 8 OFF = N/C Safety Circuit

ON

1 second

2 second

4 second

8 second

16 second

Motor Voltage

Page 2 of 5

DIPSWITCH

SETTINGS – Cont. 2. Use the chart (at right) for a quick-reference for time delay settings (switches 1 through 5).

Factory setting is 7 seconds.

Example:

The normal closing cycle of an automatic door lasts about 7 seconds. In order to get the proper closing lock out time delay needed for the closing cycle of the door, the dipswitches need to be set according to the chart on page 3 for 7 seconds. To get the

Seconds

1

2

3

4

5

6

7

8 dip 1

1 sec

ON

OFF

ON

OFF

ON

OFF

ON

OFF dip 2

2 sec

OFF

ON

ON

OFF

OFF

ON

ON

OFF dip 3

4 sec

OFF

OFF

OFF

ON

ON

ON

ON

OFF dip 4

8 sec

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON dip 5

16 sec

OFF

OFF

OFF

OFF

OFF

OFF

OFF

OFF proper lock out time delay dip switches 1, 2, & 3 must be in the ON position and Dip Switch 4 must be in the OFF position.

9

10

11

12

ON

OFF

ON

OFF

OFF

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

OFF

OFF

OFF

OFF

13

14

15

16

17

18

ON

OFF

ON

OFF

ON

OFF

OFF

ON

ON

OFF

OFF

ON

ON

ON

ON

OFF

OFF

OFF

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

OFF

ON

ON

ON

19

20

ON

OFF

ON

OFF

OFF

ON

OFF

OFF

ON

ON

21

22

23

24

ON

OFF

ON

OFF

OFF

ON

ON

OFF

ON

ON

ON

OFF

OFF

OFF

OFF

ON

ON

ON

ON

ON

25

26

ON

OFF

OFF

ON

OFF

OFF

ON

ON

ON

ON

27

28

29

30

31

ON

OFF

ON

OFF

ON

ON

OFF

OFF

ON

ON

OFF

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

ON

3. DIPSWITCH #6: Corresponds to the type of motor voltage logic on the RED and BLACK wires. Dipswitch 6 should be on for all applications that have the red and black wires going to a parallel motor connection. Dipswitch 6 should be OFF for applications where voltage is present on the red and black wires at the closed door position, and where 0 volts is present at the door open position.

4. DIPSWITCH 7 OFF & 8 ON: Provides a CLOSED circuit between the GREEN (COMMON) and YELLOW (SAFETY) during BODYGUARD detection and an OPEN circuit at all other times.

5. DIPSWITCH 7 ON & 8 OFF: Provides a OPEN circuit between the GREEN (COMMON) and YELLOW (SAFETY) during

BODYGUARD detection and a CLOSED circuit at all other times. (Example: Besam PowerSwing).

Brand / Model Of Operator

Besam Swingmaster (ETIK)

Besam Swingmaster MP

(CUP)

Dipswitch 6, 7 & 8 Setting

6 ON, 7 OFF, 8 ON

6 OFF 7 OFF, 8 ON

Besam Electra 150

Besam PowerSwing

6 ON, 7 OFF, 8 ON

6 ON, 7 ON, 8 OFF

Doromatic Astro-Swing

Mid-Swing

Senior Swing

Gyro-Tech (all except Gemini

710 AND U11)

Horton 4000

Horton 7000

KM 2000

Stanley Magic Swing

Magic Force (with safety)

6 ON, 7 OFF, 8 ON

6 ON, 7 OFF, 8 ON

6 ON, 7 OFF, 8 ON

6 ON, 7 OFF, 8 ON

6 ON, 7 OFF, 8 ON

6 ON, 7 OFF, 8 ON

75.1041.06 20060605 Page 3 of 5

SET-UP

INSTRUCTIONS

The following instructions pertain to the setup procedures and the related indications that should be observed.

RED LED

Bodyguard’s output is

Applied to the safety circuit

GREEN LED

Bodyguard’s output is

Applied to the activation circuit

Set the dipswitches according to the chart below to achieve the desired lock out time delay.

Immediately following each step, is a corrective action to perform if the step does not pass:

1. Set the On-Off-Hold Open switch to the OFF position. If a switch is not available, unplug the activating device for the door.

2. To begin the set-up, apply power to the door system, to the LO-21U module, and to the Bodyguard. The

Bodyguard shall immediately begin flashing green to indicate a setup for the closed door position.

‰ If the Bodyguard does not begin flashing green, check to insure it is receiving the correct power at inputs

1 & 2 at the 7-position terminal at the left side of the Bodyguard. Correct as necessary.

3. Do not enter into the field of detection while the Bodyguard is setting up. After approximately 6 seconds, the green

LED will expire.

4. Activate the door to the open position with the On-Off-Hold Open switch, or by jumpering the activate circuit. The

Bodyguard shall begin flashing green again while it is learning the “door open” set-up. Again, approx. 6 seconds of un-interruption will allow a setup to complete. Once complete, the door should begin to close if activation is removed. Place the On-Off-Hold Open switch to the On position. Normal operation thereafter.

‰ If the Bodyguard does not begin flashing green when the door reaches full open, improper voltage may exist on terminals 6 & 7 of the Bodyguard. Perform following:

¾ Using a BEA remote control, and with the door in the open position, unlock the Bodyguard, then press the Magic Wand key and then the number 2. This will force a setup for the open door position.

If the green LED does not begin flashing, unplug the 7-position connector at the Bodyguard.

¾ Use a multi-meter (set to a DC voltage scale) to test the voltage at terminal 6 & 7. Place the positive probe on terminal 7 and the negative probe on terminal 6. There should be approximately 12 Volts

DC. If voltage is 0 volts, check the white and red/white striped wires from the connector back to the

LO-21U for any breaks.

¾ If wiring is good, check the voltage at the red and black wires on the LO-21U. Using a multi-meter, place the positive probe on the red wire, and the negative probe on the black wire. Voltage should not be less than 6 volts DC. If it is less, try increasing the stall voltage at the door control. If voltage is 0 volts, make sure there is a good connection on the red and black wires. Also make sure the LO-

21U has the proper input voltage at the orange and brown wires.

5. Once the Bodyguard is functioning correctly with regard to the open and closed door setup, walk testing may begin.

‰ Do NOT proceed with walk-test until the Bodyguard is functioning correctly.

6. The LO-21U has two LED’s to indicate what function it is performing. When the door is closed and someone steps into the detection zone of the Bodyguard, the illumination of the red LED on the LO-21U will indicate that the LO-

21U is triggering the safety circuit. Therefore, the door will remain closed until the Bodyguard zone is clear. The red LED will expire on the LO-21U and on the Bodyguard will shut off when the detection zone is clear. With the door in the closed position, stand in the Bodyguard detection field and have someone activate the door (Eagle, push plate, etc.). The door should not open. Clear the detection field of the Bodyguard, while keeping the door activated. The door should open thereafter.

‰ If the red led comes on at the Bodyguard, but not at the LO-21U, check to insure good wiring on the gray and violet wires between the Bodyguard and the LO-21U.

‰ If the red LED comes on at the Bodyguard and the LO-21U, but the door has no safety, check the green and yellow wires between the LO-21U and the door control. If connections are good, jumper the common and safety terminals at the door control, then activate the door to insure that the safety function is ok.

7. Once the Bodyguard zone is clear and the door has been activated, it will open and remain open as long as there is activation, or until door control and sensor hold-times have expired. If someone steps into the Bodyguard zone when the door is open, the illumination of the green LED will indicate that the LO-21U is triggering the activation

circuitry of the door, thus holding the door open for as long as someone is in the Bodyguard detection pattern.

‰ If the red led comes on at the Bodyguard, but not at the LO-21U, check to insure good wiring on the gray and violet wires between the Bodyguard and the LO-21U.

‰ If the red LED comes on at the Bodyguard and the green LED comes on at the LO-21U, but the door does not hold open when the Bodyguard is in detection, check the blue and green wires between the LO-

21U and the door controls activation circuit.

‰ Reverse the red and black wires at the LO-21U and try Step 7 again.

‰ If all steps are Ok, LO-21U may be faulty. Replace as necessary.

75.1041.06 20060605 Page 4 of 5

SET-UP

INSTRUCTIONS –

Cont.

TROUBLE-

SHOOTING

COMPANY

CONTACT

8. When all functions of the control and LO-21U have been confirmed, the lockout time delay will need to be set. Time delay is set by using dipswitches 1 through 5. Perform the following steps:

‰ Activate the door to the open position.

‰ Allow the door to close and count how many seconds it takes for the overall door closing cycle

‰ Configure the dip switches according to the chart on Page 3 for the lock out time that is required

‰ Activate the door again to the open position

‰ Stand outside of the Bodyguard detection pattern, and while the door is closing, observe the red LED on the Bodyguard

‰ The red LED on the Bodyguard should NOT illuminate during the closing cycle. If it does, it is probably seeing the door at the very last degree or two of door closing, which would indicate that the lock out time needs to be slightly increased.

‰ Reconfigure the dipswitches to add 1 second of lock out time.

‰ When the lock out time is correct. The red LED will not illuminate during the entire closing cycle of the door.

‰ The last test is to insure that the Bodyguard detects an object as soon as the door has stopped closing.

Simply allow the doors to begin closing, and step in behind the doors, into the Bodyguards field of detection (be sure to NOT break the path of the lockout safety beams, if so equipped). The red LED shall illuminate and remain on at the Bodyguard, and at the LO-21U, as soon as the door reaches the fully closed position, provided that an object remains in the Bodyguard’s detection field.

PROBLEM PROBABLE CAUSE CORRECTIVE ACTION

With the door closed, the RED

LED does not come on upon

Bodyguard detection.

No Power applied to the Brown (+) and Orange (-) wires.

Or

The Gray and Violet wires are not properly connected to the

Bodyguard pins 3,4.

Step 1. Check for power 12-24 VAC / 15-24 VDC on the Brown (+) and Orange (-) wires with a meter. If voltage is there go to Step 2.

Step 2. Jumper across Bodyguard connector pins

3,4.

• RED LED does not come on, go to Step 3.

• RED LED comes on, go to Step 4.

**Step 3. Check continuity with a meter on the

Orange, Brown, Violet and Gray wires from the back of the harness connector to the ends of the

With the door closed, the

GREEN LED comes on upon

Bodyguard detection.

Dipswitch# 6 is in the wrong position. wire. Correct any problem connections. If no problem connections are found, replace LO21U.

Step 4. Check Bodyguard Relay Mode function is set to 1. If OK replace Bodyguard.

Step 1. Check that Dipswitch# 6 is set correctly for the application.

Step 2. Remove harness from lockout and re-

With the door open, the

GREEN LED does not come on upon Bodyguard detection.

Reversed polarity or no motor voltage on the RED and BLACK wires. install (this resets the LO21U).

Step 3. Check motor voltage in door closed and open position. Call Technical support.

Step 1. Check Dipswitch# 6 is correct for application.

**Step 2. Check RED and BLACK wire connections at the motor or source of door open voltage. Correct any problem connections.

Step 3. Reverse RED and BLACK LO21U wires at the motor.

No LED display on the LO21U or

Bodyguard and door will not open.

Dipswitch# 7,8 are in the wrong position.

Step 1. Check Dipswitches# 7,8 for proper position for application.

Step 2. Check control box connections for the

Yellow, Green and Blue wires.

** Remove power from sensors and door control before performing these checks..

NOTE: Lockout Relay will not function correctly when power close function is enabled on the door control.

Do not leave problems unresolved. If a satisfactory solution cannot be achieved after troubleshooting a problem, please call B.E.A.,

Inc. If you must wait for the following workday to call B.E.A., leave the door inoperable until satisfactory repairs can be made. Never sacrifice the safe operation of the automatic door or gate for an incomplete solution.

The following numbers can be called 24 hours a day, 7 days a week. For more information, visit www.beainc.com

.

West: 1-888-419-2564

South-East: 1-800-407-4545

US and Canada: 1-866-249-7937

Mid-West: 1-888-308-8843

North-East: 1-866-836-1863

Canada: 1-866-836-1863

75.1041.06 20060605 Page 5 of 5

advertisement

Related manuals

advertisement