Clarion | MS2005 | Technical data | Clarion MS2005 Technical data

MS2005BO.QXD 6/27/2002 2:25 PM Page 1
MS2005BO.QXD 6/27/2002 2:25 PM Page 2
ongratulations on your purchase of this Ungo System. Please
read this manual thoroughly to familiarize yourself with your
system’s components and operation. Discuss any questions you
might have with your installing dealer.
C
Record the serial number of your Ungo System and keep all dealer
records and receipts. Be sure to discuss the installation with the dealer
so that you understand the specifics of the installation in your vehicle.
CAUTIONS
• USE OF THE UNGO MS2005 IS THE RESPONSIBILITY OF THE OWNER.
• KEEP THE REMOTE TRANSMITTERS OUT OF THE REACH OF CHILDREN.
• THE UNGO MS2005 IS NOT INTENDED FOR USE ON VEHICLES EQUIPPED
WITH A MANUAL TRANSMISSION.
• BE SURE THE TRANSMISSION IS IN PARK BEFORE LEAVING THE VEHICLE.
• ONLY REMOTE START THE VEHICLE IN A WELL VENTILATED AREA.
MS2005BO.QXD 6/27/2002 2:25 PM Page 3
Table of Contents
1.
About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1
2.
Remote Transmitters
Remote Transmitter Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Optional Driver Door Priority Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2
Battery Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Adding a New Transmitter into the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
Additional Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3
3.
Security Features
Remote Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4
Remote Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 4
Tamper Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5
Silent Arming / Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5
Arming Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5
Passive Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 5
Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Emergency Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 6
Automatic System Rearming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 7
4.
Remote Start Features
Remote Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Stop and Go Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 8
Automatic Cold Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 9
5.
Other Features
Valet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Ignition Controlled Door Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Ignition Controlled Door Unlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 10
Dome Light Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
Auxiliary Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
Remote Sensor Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 11
6.
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 12
7.
Reference Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 13
8.
System Indications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
9.
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 14
10.
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 15
Note: Certain features described in this manual may require additional parts and/or labor. Also, some features of
the Ungo MS2005 system have selectable options that must be activated or programmed during the system’s
installation. These items will be identified in the following sections. Your Authorized Ungo Dealer will be
happy to discuss these features with you and help you design your system to meet your needs.
MS2005BO.QXD 6/27/2002 2:25 PM Page 4
MS2005BO.QXD 6/27/2002 2:25 PM Page 1
About Your Ungo System
The Ungo MS2005 is a state-of-the-art combination vehicle security and remote controlled car
starter system. The MS2005 offers security features designed to deter and detect potential
intrusions to your vehicle. It will alert and inform the driver and people in the vicinity of your vehicle
when a zone is violated.
The MS2005 will inform the user of any bad switches or sensors that may be causing the system
to function improperly, and in the event that the system is triggered, the MS2005 will even specify
which zone was violated. The MS2005 protects both you and the contents of your vehicle with
features such as panic mode, dome light illumination, and ignition controlled door locking.
In addition to its security features, the MS2005 will safely start your car by remote control, without
your key in the ignition. If your vehicle is powered by a diesel engine, the MS2005 will turn on the
ignition for several seconds prior to starting the engine, in order for the glow plugs to warm up.
Once the MS2005 has started the engine, it will turn on your preset accessories (heater/air
conditioner) to provide you with the maximum comfort when you enter your vehicle. After activation,
the MS2005 will allow the vehicle to run for approximately 12 minutes (or 24 minutes if selected by
your installer at the time of installation) before automatically shutting off.
Each Ungo MS2005 System comes with:
•
•
•
•
•
•
•
Main Unit
2 - Four Button Remote Transmitters
125dB Siren
Extended Range Receiver
Status LED
2 Stage Electronic Shock Sensor
Emergency Override / Valet Switch
Safety Features
• Brake Pedal Shutdown - Shuts down the remote start when the brake pedal is pressed.
• Hood Pin Switch Protection (optional) - Prevents the engine from being started while
the hood is open.
• Valet Mode - Prevents the vehicle from being started when being serviced.
Options and Convenience Features
The advanced design of the Ungo system incorporates a number of optional inputs and outputs
allowing you to create a customized security / convenience system by easily accommodating
many optional convenience and security features such as:
Door Locking
Remote Window Control
Power Trunk / Hatch Release
Glass Breakage Sensor
Radar Sensor
Back-up Battery Siren
MS2005 Owner’s Manual - Page 1
MS2005BO.QXD 6/27/2002 2:25 PM Page 2
Remote Transmitters
Remote Transmitter Layout
LED
Button 1
Button 2
Button 3
Button 4
The Ungo MS2005 comes with 2 multi-function Remote Transmitters used to control nearly all of
the system’s features.
Each time a transmitter button is pressed, the LED will flash to indicate that a transmission is
taking place.
Button 1 Arms the system. This button also locks the doors when the system is in Valet Mode.
Button 2 Disarms the system. This button also unlocks the doors when the system is in Valet
Mode.
Button 3 Activates the system’s Auxiliary Function, commonly used for trunk release.* Also used to
arm / disarm the system silently.
Button 4 Activates the system’s Remote Start Feature.
Optional Driver Door Priority Feature*
This configuration adds the security of unlocking only the driver’s door when the system is
Disarmed. Pressing the Disarm button again will unlock all remaining doors.
Button 1 Arms the system. This button also locks the doors when the system is in Valet Mode.
Button 2 Disarms the system and unlocks the driver’s door. This button also unlocks the doors
when the system is in Valet Mode.
If the system is Armed, pressing Button 2 will Disarm the system and unlock the driver’s door only.
If the system is Disarmed, pressing Button 2 will unlock all remaining doors.
If the system is in Valet and the doors are locked, pressing Button 2 will unlock the driver’s door. Pressing Button
2 again will unlock all remaining doors.
*Extra parts and/or labor may be required to properly utilize this feature. See your Authorized Ungo Dealer for details.
Page 2 - MS2005 Owner’s Manual
MS2005BO.QXD 6/27/2002 2:25 PM Page 3
Battery Replacement
Your Ungo Remote Transmitter uses a 12 volt alkaline battery, which will need to be replaced
from time to time. Under normal conditions, the battery should last for up to a year before it
needs replacement.
When your Remote Transmitter’s battery is in need of replacement, you will notice a decrease in
your system’s operating range or a decrease in the brightness of the Transmitter’s LED indicator.
To change the battery, remove the 2 screws at the back of the Transmitter and carefully separate
the top and bottom halves of the Transmitter case.
Insert the new battery, making sure that the positive and negative terminals are positioned
correctly and replace the cover.
Adding a New Transmitter into the System
Have all desired transmitters ready (up to 3 transmitters) and follow the steps below:
1. Turn on the ignition.
2. Press and hold the Override switch.
• The status LED will turn on red.
• The siren will chirp 3 times.
3. Have all desired transmitters ready and within 5 seconds follow the steps below for each
transmitter.
For remote arming with chirp confirmation continue holding the Override switch and
press Transmitter Button 1.
--- or --For remote arming without chirp confirmation release the Override switch and press
Transmitter Button 1.
• The parking lights will flash once quickly to confirm that the new Remote Transmitter
has been added.
4. Wait 5 seconds then turn off the ignition.
Any transmitters that were previously learned to this system and not included in this procedure
will no longer operate this system.
Additional Remote Transmitters
Additional Remote Transmitters for your MS2005 are available from your Authorized Ungo
dealer.
MS2005 Owner’s Manual - Page 3
MS2005BO.QXD 6/27/2002 2:25 PM Page 4
Security Features
Remote Arming
When Armed, the system monitors and protects 3 independent areas, or zones, including the
doors, hood/trunk, and shock sensor.
To Arm the system:
1. Turn off the ignition.
2. Press Button 1.
•
•
•
•
The siren/horn will chirp once.*
The doors will lock.
The parking lights will flash once.
The LED will turn on red, indicating the doors, hood and trunk inputs are activated.
* The siren chirp(s) during Arming will alert you the condition of the system and vehicle when the system is armed.
1 chirp
1 + 4 chirps
=
=
normal arming
door, hood, or trunk open
During Arming, if the system detects a bad sensor or an open zone, the system will ignore that input, but keep all
other areas protected.
3. After 10 seconds:
• The LED will begin blinking, indicating that the shock sensor is activated.
While the system is Armed, the system will trigger if:
• The doors are opened.
• The shock sensor detects an impact to the vehicle.
• The hood or trunk is opened.
When triggered, the siren will sound, and the parking lights will flash and the horn will honk
(if connected). If the system is triggered by the doors, hood, or trunk, the system will alarm
for 40 seconds. If triggered by the shock sensor, the system will alarm for 20 seconds.
If the same input triggers the system 3 times during a single arming cycle, the system will
bypass that input keeping the other zones protected until the next time the system is armed.
If the shock sensor detects a light impact to the car, the siren will sound 5 chirps to warn
away the potential intruder.
Remote Disarming
To Disarm the system:
Press Button 2.
• The siren/horn will chirp twice.*
• The doors will unlock.**
• The parking lights will flash twice.*
• The LED will turn off.
Page 4 - MS2005 Owner’s Manual
MS2005BO.QXD 6/27/2002 2:25 PM Page 5
* The siren chirps and light flashes during disarming will alert you if the system had been triggered while armed.
2 chirps / 2 flashes
3 chirps / 3 flashes
=
=
normal disarming
Tamper Alert - system was triggered
** If the Passenger Unlock Feature is installed, pressing Button 2 will unlock only the driver’s door. Pressing the
unlock Button 2 again unlocks all doors.
Tamper Alert
On Disarming, if the system responds with three chirps, indicating the system was triggered, the
LED will flash for 60 seconds to indicate the zone that triggered the system.
1 flash
=
door
2 flashes
=
shock sensor
3 flashes
=
trunk
example: flash-flash-pause-flash-flash-pause = shock sensor
Silent Arming / Disarming
Each Remote Transmitter can be individually set to Arm and Disarm the system with or without
chirp confirmation at the time they are programmed into the system (see Adding a New
Transmitter into the System).
To mute the Arming and Disarming confirmation chirps, you can Arm or Disarm the system by
pressing Button 3.
Note: The confirmation chirps will only be cancelled if the system status is normal. The chirp indications for Tamper
Alert and the open zone warning will not be cancelled when the system is Armed or Disarmed silently .
Arming Mode Selection
The system can be set in one of the following Arming Modes:
• Passive (automatic) Arming with chirp confirmation
• Active Arming (by Remote Only)
• Passive (automatic) Arming without chirp confirmation
To set the Arming Mode:
1. Turn the ignition on.
2. Within 4 seconds, press the Transmitter button corresponding to desired operation.
Button 1 / 1 chirp
Button 2 / 2 chirps
Button 3 / 3 chirps
=
=
=
Active Arming
Passive Arming with chirp
Passive Arming without chirp
Note: If no buttons are pressed for 5 seconds, Arming Mode Selection is automatically exited.
3. Turn the ignition off to save the selection.
Passive Arming
When the Arming Mode has been set for Passive Arming, the system arms itself automatically,
each time the ignition is turned off and all of the doors, hood and trunk are closed.
MS2005 Owner’s Manual - Page 5
MS2005BO.QXD 6/27/2002 2:25 PM Page 6
To start the Passive Arming Process:
1. Turn off the ignition.*
• The status LED will begin to flash quickly.
2. Open the door and exit the vehicle.
• Once all doors are closed and the dome light is turned off, the LED will turn off.
3. After 20 seconds,
• The siren will chirp (if Passive Arming with chirp is selected).
• The parking lights will flash.
• The doors will lock.**
• The status LED will flash red, indicating the system is armed.
4. The system is now armed.
* The ignition must have been on for at least 10 seconds before the Passive Arming sequence will begin.
** If the Passive Locking feature is selected.
To temporarily disable Passive Arming, you can turn the ignition key on then off within 10 seconds.
The status LED will stop flashing, and the system will not passively arm until the next time the key
is on for more than 10 seconds. This feature is useful for turning off passive arming when
refueling, washing the car, or if you want to sit in your car and do not want the system to arm.
Panic Mode
Allows you to instantly trigger the alarm in an emergency situation using the Remote Transmitter.
To enter Panic Mode:
1. Press and hold Button 1 for 3 seconds.
• The siren will sound.
• The doors will unlock.
2. Press Button 1 again to stop panic and place system into the Armed state.
3. Press Button 2 to stop panic and place system into the Disarmed state.
If Panic Mode is not stopped by the Remote, it will automatically time out after 40 seconds, and
the system will return to its prior Armed/Disarmed state.
Emergency Override
In case your Remote Transmitter becomes inoperable, or it is lost or stolen, you can still enter
and drive your car by using the following procedure. Be sure that you have your ignition keys
ready and that you know the location of the Override switch before you perform this procedure.
To override the system:
1. Unlock the door using the key.
2. Enter the vehicle.
• Because the system is armed, the system will trigger and the siren will be sounding.
Page 6 - MS2005 Owner’s Manual
MS2005BO.QXD 6/27/2002 2:25 PM Page 7
3. Turn ignition key on.
4. Within 4 seconds, press and hold the Override switch.
• The system will disarm.
5. You can now start and drive the car.
Note: During installation, your installer can program the system to give 10 second entry delay when the system Arms
passively. When the door is opened while the system is Armed, the siren will give a series warning of chirps
before sounding, giving you time to perform the emergency override procedure.
Automatic System Rearming
This feature, which can be turned on by your installer during the installation, insures the security of
the system by protecting your car in case of an accidental disarm.
If your system becomes disarmed due to an accidental press of the Arm/Disarm Button, the system
will automatically rearm if no other activity is detected within one minute.
One minute after Remote Disarming, the system will alert you with a series of chirps, then arm. (If the
Passive Door Locking feature is selected during the installation, the system will also relock the doors.)
Any of the following will cancel Automatic System Rearming:
• Turn on the Ignition.
• Open the Trunk or Hood.
• Activate the Auxiliary Function.
Automatic System Rearming is independent of Passive Arming and only takes place if the system was
Armed (actively or passively) for at least 10 seconds and then Disarmed by the Remote Transmitter.
MS2005 Owner’s Manual - Page 7
MS2005BO.QXD 6/27/2002 2:25 PM Page 8
Remote Start Features
Remote Starting
To Remote Start the System:
1. Be sure the System is not in Valet Mode.
2. Press Button 4.
•
•
•
•
•
•
The parking lights will turn on.
The siren will chirp 3 times (if the system is Armed, the shock sensor will turn off).
The ignition will turn on.
The engine will start and run for the duration of its programmed Run Timer.*
The heater or air conditioner will turn on (if turned on prior to exiting the vehicle).
The LED will double flash.
*If the engine fails to start on the first attempt, it will repeat the starting procedure 2 more times.
Turning on the ignition key then pressing the brake pedal will disengage the MS2005 and allow
you to operate and drive your vehicle in a normal manner.
Shut Down
Any of the following will shut down the engine when it is under Remote Start control:
1. Press Button 4 for 3 seconds.
• After the engine shuts down the doors will lock (if installed and programmed).
2. Press the brake pedal.
3. Open the hood (or trunk if connected).
4. Remote Start Time-Out (completion of the timed run cycle).
Stop and Go
The Stop and Go Feature allows you to remove the ignition key and exit the vehicle while keeping
the engine running during short stops.
To leave the vehicle running:
1. Press the brake pedal and hold.
2. While pressing the brake pedal, push Button 4 on the Remote Transmitter for 2 seconds.
• The LED will flash rapidly.
• The parking lights will flash 5 times.
3. Release the brake pedal.
4. Remove the key from the ignition switch.
5. You may now exit the vehicle, arm the alarm and lock the doors.
Page 8 - MS2005 Owner’s Manual
MS2005BO.QXD 6/27/2002 2:25 PM Page 9
To re-enter the vehicle and resume driver control:
1. Disarm the alarm by pressing Button 2 on the Remote Transmitter.*
• The doors will unlock.*
2. Turn on the ignition.
3. Press the brake pedal to disengaged the MS2005.
• The LED will turn off.
*If optional keyless entry feature is installed.
Auto Cold Starting
The Auto Cold Starting Feature automatically starts the vehicle every two hours and runs for the
preset Run Time.
To enter Cold Start Mode:
1. Be sure ignition is off.
2. Press and hold the Valet switch.
3. Continue holding the Valet switch and press Transmitter Button 3 for 5 seconds then
release both buttons.
• The parking lights will flash 5 times.
• The engine will start and run for 30 seconds then shut down.
• The LED will double flash.
4. The system will remain in Cold Start Mode until the vehicle is started using the
transmitter or the Cold Start Feaure has completed all the run cycles.
Note: Pressing the brake pedal will also turn off the Auto Cold Starting Feature.
MS2005 Owner’s Manual - Page 9
MS2005BO.QXD 6/27/2002 2:25 PM Page 10
Other Features
Valet Mode
Allows you to temporarily disable the security system when the car is being service or turned over
to a parking attendant.
To turn Valet Mode on or off:
1. Turn on the ignition.
2. Press and hold the override switch.
3. While holding the override switch, turn off the ignition.
• The siren will chirp once to indicate you have turned Valet Mode on.
• The siren will chirp twice to indicate you have turned Valet Mode off.
4. Release the override switch.
While Valet Mode is on, the LED will light solid and you can continue to lock and unlock your
doors with the Remote Transmitters, as well as operate the Auxiliary Function.
For added protection, when the doors are locked using the Remote Transmitter, the system’s
Starter Disable circuit will activate, and the LED will emit double flashes until the system is
unlocked by the RemoteTransmitter.
If the Remote Transmitter is lost, stolen, or becomes inoperable while the car is locked in Valet
Mode, you can exit the Valet mode to deactivate the Starter Disable circuit.
Ignition Controlled Door Locking
For added convenience and safety, this feature automatically locks your car’s doors 10 seconds
after the ignition key is turned on.
To prevent you from accidentally locking your keys inside the car:
• The system will not automatically lock the doors if a door is open when the ignition key is turned on.
• The system will not automatically lock the doors if a door is opened during the first 10 seconds after the ignition
key is turned on.
Ignition Controlled Door Unlocking*
For added convenience, this feature automatically unlocks your car’s doors after the ignition key
is turned off.
*For personal safety reasons, this feature can be turned off by your installer.
• If driver’s door priority is selected only the driver’s door will unlock after the ignition key is turned off.
Page 10 - MS2005 Owner’s Manual
MS2005BO.QXD 6/27/2002 2:25 PM Page 11
Dome Light Control
The dome light will turn on for 20 seconds when the system is disarmed (or unlocked in Valet
Mode) using the Remote Transmitter.
Auxiliary Function
This function will operate regardless of whether the system is armed or disarmed and will stay
active for as long as the Button 3 is held. To operate the auxiliary function, press Button 3.
Remote Sensor Bypass
The system can be set up so that in case of extreme weather conditions (such as high winds),
the shock sensor can be temporarily bypassed using the Remote Transmitter, while the system
is armed, to prevent false alarming.
To Bypass the sensors:
1. After arming the system, press Button 3 on the Remote Transmitter within 2 seconds.
• The siren will chirp 5 times, indicating the sensors have been bypassed.
2. The sensors will remain bypassed until the next time the system is armed.
MS2005 Owner’s Manual - Page 11
MS2005BO.QXD 6/27/2002 2:25 PM Page 12
Notes
Page 12 - MS2005 Owner’s Manual
MS2005BO.QXD 6/27/2002 2:25 PM Page 13
Reference Chart
You can use this chart to quickly identify and interpret your system’s chirp indications and LED
flashes.
Output
When
Status
1 chirp
1 + 4 chirps
arming
arming
normal arming
door, hood, or trunk is open
no chirps
LED double flashes
arming
Valet Mode
Valet Mode is on
Starter Defeat is activated
2 chirps
3 chirps
1 LED flash
2 LED flashes
3 LED flashes
disarming
disarming
after Tamper Alert
after Tamper Alert
after Tamper Alert
normal disarming
Tamper Alert - system was triggered
door
shock sensor
hood or trunk
5 chirps
continuous chirps
while armed
while armed & door open
Warn Away
System Triggered
(Passive Arming Entry Delay)
4 chirps
1 chirps
with ignition key on
in Sensor Test Mode
Sensor Test Mode is on
impact detected
multiple chirps for 10 seconds
1 minute after disarming
Automatic Rearming
LED flashing quickly
ignition key off
Passive Arming sequence started
MS2005 Owner’s Manual - Page 13
MS2005BO.QXD 6/27/2002 2:25 PM Page 14
System Indications
You can use these tables to quickly identify and interpret the MS2005’s parking light and LED
indications.
Status LED Indications
Flashes
Slow
Rapid
Solid
Double
Triple
Functions
System is Armed
Remote Started/Running
Valet mode
Auto Cold Starting engaged
System Armed & Remote Started
Parking Light Indications
Flashes
1
2
3
Functions
System is Armed
System is Disarmed
Auto Cold Starting engaged
Technical Data
FCC ID:
Specifications
Main Unit
Voltage: 12v, negative ground
Current Consumption: <15mA
Temperature Range: -40oF to +257 oF
Auxiliary Output Capability: 500mA
Internal Relays: (4) 30A, (1) 15A
MP62ZUUNGO701-702
HP92VUUNGO7000-2
THIS DEVICE COMPLIES WITH FCC RULES PART 15.
O PERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) T HIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE THAT MAY BE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Transmitter
Current Consumption: <.00mA, standby
Battery Type: miniature 12v, type 23A
Warranty Information
Model No.: MS2005
Serial No.:
Dealer Name:
Address:
Purchase Date:
Page 14 - MS2005 Owner’s Manual
Ungo Security Corporation
Gardena, CA
USA
MS2005BO.QXD 6/27/2002 2:25 PM Page 15
Warranty Information
1. Ungo Security Corporation of Gardena, California ("Ungo
Security") warrants this Ungo system to be free from defects in
materials and workmanship and to comply with Ungo Security’s
applicable printed specifications.
2. Ungo Security systems carry a limited lifetime warranty on
the Main unit (system brain) and transmitters. The warranty is
limited to Ungo Security systems that have been installed by an
approved Ungo dealer and is extended to the Original
Purchaser ("Owner") and to the original vehicle in which it was
installed only, and is not transferable to any subsequent owner
or owners of the product(s).
All other products (including those products of other
manufacturers which are supplied by Ungo Security as a part
of, or an accessory to, an Ungo Security-manufactured
product) are warranted by Ungo Security for a period of one
year from the date of sale to the Owner. For specific
identification of such products contact Ungo Security.
3. This warranty shall not cover: (I) any damage caused by
Owner’s negligence or misuse of any kind, or any damage due
to causes unrelated to Ungo Security’s manufacturing,
including, but not limited to improper servicing or repair by
someone other than Ungo Security or an authorized service
facility: (II) alterations or modifications to the Ungo system
other than the addition of an authorized accessory: or (III)
improper installation or removal from the vehicle contrary to
Ungo Security’s instructions.
4. Obligations of Ungo Security. In the event the Owner’s
Ungo system does not comply with this warranty, it must be
returned to Ungo Security as specified below. Ungo Security
will repair or replace it with a new, comparable, or reworked
unit, within thirty (30) days of receipt and acceptance of such
defective unit, and without cost to Owner.
5. To make a claim under the warranty. Owner must: (I)
provide Ungo Security with written notice that the Ungo System
does not comply with the warranty within thirty (30) days from
the date of the Owner’s discovery of the defect and (II) furnish
proof of purchase and purchase date (this requirement is
satisfied if Ungo Security has a completed warranty registration
card on file).
6. Owner obligations. To obtain Warranty Service, Owner must
at Owner’s expense: (I) have the Ungo system removed from
the vehicle by an authorized Ungo Security dealer, (II) package
the unit in a reasonable manner to prevent damage to the unit
during shipment; and (III) ship the unit, freight prepaid, to Ungo
Security’s factory or other authorized repair facility.
7. Repair facility locations. To obtain the name, address and
phone number of the nearest Authorized Ungo Repair Facility,
Owners may contact Ungo Security at 310-327-9100.
8. The Owners of Ungo systems in California have the right to
have the product serviced or repaired during the warranty
period. The warranty period will be extended for the number of
full days that the product has been out of the Owner’s hands for
warranty repairs. If a defect exists within the warranty period,
the warranty will not expire until the defect has been fixed. The
warranty period will also be extended if the repair has not been
performed due to delays caused by circumstances beyond the
control of the Owner, or if the warranty repairs did not remedy
the defect and the Owner notifies Ungo Security or the seller of
the failure of the repairs within sixty (60) days after they were
completed. If, after a reasonable number of attempts, the defect
has not been fixed the Owner may return this product for
replacement or a refund, subject in either case, to a deduction
of a reasonable charge for usage. The time extension does not
effect the protection or remedies the Owner has under other
laws.
9. Exclusions from liability.
(A) In no event shall Ungo Security be liable for any loss or
damages beyond the original purchase price of the Ungo
system , and Ungo Security specifically excludes any and all
incidental and consequential damages, whether resulting from
breach of warranty or contract, negligence or other conduct in
connection with any sale, use, servicing or repair of a unit.
(Some states do not allow the exclusion of incidental or
consequential damages, so the above exclusion may not apply
to you.)
(B) There are no warranties, express, statutory or implied,
which extend beyond that which is described herein, and in
particular, all implied warranties of merchantability and fitness
for a particular purpose, and all warranties of title and against
encumbrances, are expressly disclaimed, limited and excluded
as permitted by law; but in no event shall any implied warranty,
whether of merchantability of fitness for a particular purpose or
otherwise, have a duration exceeding that of the express
warranty made herein. (Some states do not allow limitation on
how long an implied warranty lasts, so the above limitation may
not apply to you.)
(C) No agent, officer, employee or representative of Ungo
Security, or any other person, has authority to make any
representations, promises or warranties respecting Ungo
systems and their authorized accessories.
(D) Owner has the right to bring any action at law or in equity
to resolve disputes concerning, or to enforce, the provisions of
this warranty. No action at law or in equity may be brought
against Ungo Security for breach of warranty or contract or
based on negligence of other conduct more than three (3) years
from the date the cause of action has occurred.
(E) This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
(F) The remedies extended herein are the sole and exclusive
remedies available to Owners of Ungo systems.
(G) Under no circumstances should this warranty, or the
products covered by it, be construed as an insurance policy
against loss
MS2005 Owner’s Manual - Page 15
MS2005BO.QXD 6/27/2002 2:25 PM Page 16
Ungo Security Corporation
A Clarion Company
661 West Redondo Beach Blvd.
Gardena, CA 90247
800-Go-Clarion
www.clarion-usa.com
© Ungo Security Corporation, Gardena, CA
97-MS2005-10 Rev. 2 (04/01)
Download PDF