ZyXEL Communications | ES-3024 | User`s guide | ZyXEL Communications ES-3024 User`s guide

Dimension
Ethernet Switch Modules
User’s Guide
Version 1.0
May 2003
Dimension Ethernet Switch Modules User’s Guide
Copyright
Copyright © 2003 by ZyXEL Communications Corporation.
The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval
system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL
Communications Corporation.
Published by ZyXEL Communications Corporation. All rights reserved.
Disclaimer
ZyXEL does not assume any liability arising out of the application or use of any products, or software described
herein. Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further
reserves the right to make changes in any products described herein without notice. This publication is subject to
change without notice.
Trademarks
ZyNOS (ZyXEL Network Operating System) is a registered trademark of ZyXEL Communications, Inc. Other
trademarks mentioned in this publication are used for identification purposes only and may be properties of their
respective owners.
Federal Communications Commission (FCC)
Interference Statement
FCC Interference Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operations.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
CE Mark Warning:
This is a class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
Taiwanese BSMI (Bureau of Standards, Metrology and Inspection) A Warning:
Certifications
Refer to the product page at www.zyxel.com.
2
Copyright and FCC Statements
Dimension Ethernet Switch Modules User’s Guide
ZyXEL Limited Warranty
ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or
workmanship for a period of up to two years from the date of purchase. During the warranty period, and upon proof
of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL
will, at its discretion, repair or replace the defective products or components without charge for either parts or labor,
and to whatever extent it shall deem necessary to restore the product or components to proper operating condition.
Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will
be solely at the discretion of ZyXEL. This warranty shall not apply if the product is modified, misused, tampered
with, damaged by an act of God, or subjected to abnormal working conditions.
Note
Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is
in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a
particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind
of character to the purchaser.
To obtain the services of this warranty, contact ZyXEL's Service Center for your Return Material Authorization
number (RMA). Products must be returned Postage Prepaid. It is recommended that the unit be insured when
shipped. Any returned products without proof of purchase or those with an out-dated warranty will be repaired or
replaced (at the discretion of ZyXEL) and the customer will be billed for parts and labor. All repaired or replaced
products will be shipped by ZyXEL to the corresponding return address, Postage Paid. This warranty gives you
specific legal rights, and you may also have other rights that vary from country to country.
Safety Warnings
1. Do not use this product near water, for example, in a wet basement or near a swimming pool.
2. Avoid using this product during a thunderstorm. There may be a risk of electric shock from lightening.
Customer Support
Please have the following information ready when you contact customer support.
• Product model and serial number.
• Warranty Information.
• Date that you received your device.
• Brief description of the problem and the steps you took to solve it.
METHOD
E-MAIL
SUPPORT/SALES
TELEPHONE/FAX
WEB SITE/ FTP SITE
REGULAR MAIL
LOCATION
WORLDWIDE
support@zyxel.com.tw
+886-3-578-3942
www.zyxel.com
www.europe.zyxel.com
NORTH
AMERICA
SCANDINAVIA
GERMANY
Customer Support
sales@zyxel.com.tw
+886-3-578-2439
ftp.europe.zyxel.com
support@zyxel.com
+1-714-632-0882
800-255-4101
www.zyxel.com
sales@zyxel.com
+1-714-632-0858
ftp.zyxel.com
support@zyxel.dk
+45-3955-0700
www.zyxel.dk
sales@zyxel.dk
+45-3955-0707
ftp.zyxel.dk
support@zyxel.de
+49-2405-6909-0
www.zyxel.de
sales@zyxel.de
+49-2405-6909-99
ZyXEL Communications Corp.,
6 Innovation Road II, ScienceBased Industrial Park, Hsinchu
300, Taiwan.
ZyXEL Communications Inc.,
1650 Miraloma Avenue,
Placentia, CA 92870, U.S.A.
ZyXEL Communications A/S,
Columbusvej 5, 2860 Soeborg,
Denmark.
ZyXEL Deutschland GmbH.
Adenauerstr. 20/A2 D-52146
Wuerselen, Germany
3
Dimension Ethernet Switch Modules User’s Guide
Table of Contents
Copyright..................................................................................................................................................................... 2
Federal Communications Commission (FCC) Interference Statement................................................................. 2
ZyXEL Limited Warranty ............................................................................................................................................ 3
Customer Support ...................................................................................................................................................... 3
Preface......................................................................................................................................................................... 4
Ethernet Switch Modules........................................................................................................................................... 5
Introduction ............................................................................................................................................................... 5
EM3024-FX-SC: 100 Base-FX Multi-Mode Module ................................................................................................. 5
EM3024-GTP: Gigabit 1000 Base-T Module............................................................................................................ 6
EM3024-SX-SC: Gigabit 1000 Base-SX Fiber Module ............................................................................................ 7
EM3024-GBIC: GBIC (Gigabit Interface Converter) 3.3V Module ........................................................................... 8
EM3024-S: Stacking Module (for both ES-3024 and ES-4024 Ethernet switches).................................................. 8
Installing a Module ..................................................................................................................................................... 9
Preface
Congratulations on your purchase of a Dimension Ethernet Switch module.
The Ethernet switch modules discussed in this user’s guide are for Dimension ES-3024 Ethernet switches unless
otherwise specified.
The switch modules are designed to provide your network with Ethernet, Fast Ethernet and/or Gigabit Ethernet
connectivity over twisted pair and fiber optic cabling. The expansion slots on the Dimension Ethernet switch further
add to the flexibility of your network systems.
General Syntax Conventions
For brevity’s sake, we will use “e.g.” as shorthand for “for instance”, and “i.e.” as shorthand for “that is” or “in
other words” throughout this manual.
The Dimension ES-3024 Ethernet Switch will be referred to as the ES-3024, ES switch, or simply as the switch in
this manual.
Related Documentation
Dimension ES-3024 Ethernet – Ethernet Switch User’s Guide
The user’s guide covers all aspects of the ES switch operations and shows you how to get the best out of the
multiple advanced features of the ES switch using the embedded web-based configurator. It is designed to guide
you through the correct configuration of your ES switch for various applications.
ZyXEL Web Site
The ZyXEL download library at www.zyxel.com contains additional support documentation and an online glossary
of networking terms.
4
Preface
Dimension Ethernet Switch Modules User’s Guide
Ethernet Switch Modules
Introduction
With the ES-3024’s expansion slots, you can install modules to optimize your network’s performance while
reducing cost and complexity
Choose from the following modules.
• 1-port 100 Base-FX Fiber Multi-Mode module
• 1-port Gigabit 1000 Base-T module
• 1-port Gigabit 1000 Base-SX Fiber module
• GBIC (Gigabit Interface Converter) 3.3V module
• Stacking module (for both ES-3024 and ES-4024 Ethernet switches)
The following sections provide a brief description of each module.
EM3024-FX-SC: 100 Base-FX Multi-Mode Module
Diagram 1 EM3024-FX-SC: 100 Base-FX: Front Panel
Features
•
•
•
One 100Mbps fiber port (SC multi-mode connectors).
Supports full-duplex mode.
Allows connection distance of up to 2 kilometers via fiber optic cable.
Front Panel LEDs
The following table describes the LEDs on the front panel.
Table 1 EM3024-FX-SC: 100 Base-FX Fiber Module LED Description
LED
LNK/TX
RX
FDX
COLOR
Green
Green
Amber
Ethernet Switch Modules
STATUS
DESCRIPTION
On
The port is connected to an Ethernet device.
Blinking
The port is transmitting data.
Off
The port is not connected to an Ethernet device.
Blinking
The port is receiving data.
Off
The port is not receiving data.
On
The port is operating in full-duplex mode.
5
Dimension Ethernet Switch Modules User’s Guide
EM3024-GTP: Gigabit 1000 Base-T Module
Diagram 2 EM3024-GTP: Gigabit 1000 Base-T: Front Panel
Features
•
•
•
•
•
One 100/1000Mbps N-Way auto-negotiation RJ-45 port.
Supports auto MDI/MDIX (auto-crossover).
Supports half-duplex (at 100 Mbps only) and full-duplex modes.
Back-Pressure flow control in half-duplex mode (at 100 Mbps only).
Pause-Frame flow control in full-duplex mode.
Front Panel LEDs
The following table describes the LEDs on the front panel.
Table 2 EM3024-GTP: Gigabit 1000 Base-T Module LED Description
LED
1000
100
6
COLOR
Green
Green
STATUS
DESCRIPTION
On
An Ethernet device is connected at 1000 Mbps.
Blinking
The port is receiving or transmitting data.
Off
The port is not connected to an Ethernet device.
On
An Ethernet device is connected at 100 Mbps.
Blinking
The port is receiving or transmitting data.
Off
The port is not connected to an Ethernet device.
LNK/ACT
Green
On
Blinking
Off
The port is connected to an Ethernet device.
The port is receiving or transmitting data.
The port is not connected to an Ethernet device.
FDX
Amber
On
Blinking
Off
The port is operating in full-duplex mode.
Collisions occurred on this port.
The port is operating in half-duplex mode.
Ethernet Switch Modules
Dimension Ethernet Switch Modules User’s Guide
EM3024-SX-SC: Gigabit 1000 Base-SX Fiber Module
Diagram 3 EM3024-SX-SC: Gigabit 1000 Base-SX: Front Panel
Features
•
•
•
One 1000Mbps fiber port (SC multi-mode connectors).
Supports full-duplex mode.
Allows connection distance of up to 220 meters (using 62.5/125µm Multi-mode fiber) and up to 500 meters
(using 50/125µm Multi-mode fiber) via fiber optic cable.
Front Panel LEDs
The following table describes the LEDs on the front panel.
Table 3 EM3024-SX-SC: Gigabit 1000 Base Fiber Module LED Description
LED
LNK
ACT
COLOR
Green
Green
Ethernet Switch Modules
STATUS
DECRIPTION
On
The port is connected to an Ethernet device.
Off
The port is not connected to an Ethernet device.
Blinking
The port is transmitting or receiving data.
Off
The port is not transmitting and receiving data.
7
Dimension Ethernet Switch Modules User’s Guide
EM3024-GBIC: GBIC (Gigabit Interface Converter) 3.3V Module
Diagram 4 EM3024-GBIC: GBIC: Front Panel
The GBIC 3.3V module features one slot for a GBIC transceiver.
Front Panel LEDs
The following table describes the LEDs on the front panel.
Table 4 GBIC Module LED Description
LED
LNK
ACT
COLOR
Green
Green
STATUS
DESCRIPTION
On
The port is connected to an Ethernet device.
Off
The port is not connected to an Ethernet device.
Blinking
The port is transmitting or receiving data.
Off
The port is not transmitting and receiving data.
EM3024-S: Stacking Module (for both ES-3024 and ES-4024 Ethernet
switches)
Diagram 5 EM3024-S: Stacking Module: Front Panel
Features
•
•
•
Two 1000Mbps RJ-45 ports.
Supports auto MDI/MDIX (auto-crossover).
Pause-Frame flow control in full-duplex mode.
Refer to the ES-3024/ ES-4024 user’s guide for information on port and LED descriptions and cable connection
examples.
8
Ethernet Switch Modules
Dimension Ethernet Switch Modules User’s Guide
Installing a Module
Follow these steps to install a module.
Modules are NOT hot swappable!
Step 1.
Step 2.
Turn off your switch and unplug the power cord from the switch.
Loosen the screws from the cover plate and remove the cover plate from an expension slot. Do not
discard the cover plate. You can put the cover plate back on if you remove the new module.
Diagram 6 Loosening the Screws and Removing the Cover Plate
Before you continue, wear an anti-static wrist strap or touch any grounded or metal objects to
discharge any bodily static electricity.
Step 3.
Step 4.
Step 5.
Remove the module from its protective anti-static packaging. holding the module by its edgeto avoid
touch the onboard circuit components.
Insert the module into an available expansion slot on the switch. Press it firmly until the module snaps
into place.
Secure it to the switch with the retaining screws.
Slide the module into the
expansion slot until it snaps
into place.
Diagram 7 Inserting An Example Module1
Never force, bend or twist the modules into the expansion slots.
Step 6.
1
Turn on the switch. The switch automatically detects the installed module. Connect any necessary
network cables to the module and check the LEDs to verify that it is functioning properly.
This is an example module only!
Installing a Module
9
Download PDF