Dual | XD6150 | Troubleshooting guide | Dual XD6150 Troubleshooting guide

XD6150
INSTALLATION/OWNER'S MANUAL
AM/FM/CD Receiver with 3.5mm Auxiliary Input, USB Charging Port
and Detachable Face
Charge Port
XD6150 INSTALLATION
Preparation
Please read entire manual before installation.
Before You Start
•Disconnect negative battery terminal. Consult a qualified technician for instructions.
•Avoid installing the unit where it would be subject to high temperatures, such as from
direct sunlight, or where it would be subject to dust, dirt or excessive vibration.
Getting Started
• Remove trim ring from unit,
• Remove 2 transit screws located
on top of the unit.
• Insert the supplied keys into the
slots as shown, and slide the unit
out of the mounting sleeve.
• Install mounting sleeve into
opening, bending tabs to secure.
• Connect wiring harness and
antenna. Consult a qualified
technician if you are unsure.
• Certain vehicles may require an
installation kit and/or wiring
harness adapter (sold separately).
• Test for correct operation and slide
into mounting sleeve to secure.
• Snap trim ring into place.
KEYS
MOUNTING STRAP
HEX NUT
HEX BOLT
PLAIN WASHER
MOUNTING SLEEVE
TYPICAL FRONT-LOAD DIN MOUNTING METHOD
TYPICAL
FRONT-LOAD DIN MOUNTING METHOD
2
XD6150 INSTALLATION
Wiring Diagram
Rear Preamp Output
Connect to amplifier RCA input
LINE OUT
L-CH
R-CH
RCA Cable
(sold separately)
Antenna Connector
BLUE
BLACK
RED
Remote Turn-On
Connect to amplifier or power
antenna. Insulate wire if not used.
AMP
Ground
Connect to vehicle
chassis ground.
Accessory
Connect to ignition
circuit or switched 12 volt source.
10 AMP
AGC Fuse
YELLOW
Memory
Connect to battery
circuit or constant 12 volt source.
Right Front
Right Rear
Left Front
Left Rear
Gray/Black (-)
Gray (+)
White/Black (-)
White (+)
Violet/Black (-)
Violet (+)
FUSE
When replacing the fuse,
make sure new fuse is the
correct type and amperage.
Using an incorrect fuse
could damage the radio.
The XD6150 uses one
10 amp AGC fuse located
in-line.
Green/Black (-)
Green (+)
3
XD6150 OPERATION
Control Locations - Receiver
1
20
2
19
4
5
15
14
3
18
17
16
6
1
Release
11
USB Charging Port
2
Mode
12
Auxiliary Input
3
Audio/Menu
13
Tune/Track Up
4
Preset 1/Repeat
14
Tune/Track Down
5
Preset 4/Play/Pause
15
Display
6
Preset 2/Random
16
Band
7
Preset 5
17
EQ/Loudness
8
Preset 3/Intro
18
Auto Store/Preset Scan
9
Preset 6
19
Mute
20
Power ( )
10 Eject
7
13
8
9
10
12 11
The XD6150 has an easy-to-use interface that provides a rewarding experience, as
well as support for your favorite tunes. Audio CD-R and CD-RW disc playback ensures
compatibility with your music collection, and the RCA preamp output provides the right
connections to expand your system. From its front panel auxiliary input for connecting
your MP3 player, to the detachable face for security assurance, this head unit has you
covered.
4
XD6150 OPERATION
Control Locations - Remote
1
2
3
4
18
5
6
7
17
16
8
9
15
10
14
11
13
12
1
Power ( )
10
Preset 6
2
Audio/Menu
11
Preset 5
3
Volume Up
12
EQ
4
Mode
13
Display
5
Tune/Track Up
14
Mute
6
Volume Down
15
Preset 4/Play/Pause
7
Auto Store/Preset Scan
16
Preset 1/Repeat
8
Preset 3/Intro
17
Band
9
Preset 2/Random
18
Tune/Track Down
5
XD6150 OPERATION
General Operation
Faceplate Removal
Press RELEASE and pull away from the left side to remove.
To re-install, insert right side of faceplate first then push
left side to secure.
Semi-Permanent
Faceplate Installation
Remove trim ring and install supplied #1 x 7/32” Phillips
head screw through left side of mounting frame into faceplate.
Power On/Off
Press
or any other button (except eject) to turn the unit on.
Inserting a disc will turn the unit on automatically. Press
to turn the unit off.
Mode
Press MODE to select between AM/FM, CD player and
auxiliary input. Modes of operation are indicated in the
display.
Note: CD mode will not appear unless a CD is inserted.
Auxiliary Input
USB Charging Port
Insert a 3.5mm connector in the front panel AUX port.
Connect the other end of the 3.5mm connector to the
headphone output of an audio device, MP3 player, etc. Press
MODE to select AUX mode.
Insert the USB connector of a battery-powered USB device
into the USB charging port on the front panel, which provides
5 volts DC and 1.0 amps. The USB device will immediately
begin charging.
Note: The USB charging port may not be compatible with
every device due to differences in power requirements. Note: This USB port provides power only and will not play
back music from a USB device.
Volume
Mute
Press MUTE to silence the audio. “MUTE” will flash in the
display. Press MUTE again to cancel.
Reset
Press to RESET the unit upon initial installation or if
abnormal operation occurs. The reset button is located
behind the faceplate.
Display
6
Adjust volume using volume knob (00-46).
Press DISP to select between clock and different types of
information, such as radio frequency or CD track information.
XD6150 OPERATION
General Operation
Set the Clock
With the unit on, press and hold DISP until the clock begins to
flash, then release. Press TUNE
to adjust the hours and
TUNE
to adjust the minutes. Press DISP momentarily to
save the selected time.
nn
ll
12/24-hour Clock
The clock will display 12-hour AM/PM time in USA frequency
spacing mode (PM 10:00). In European frequency spacing
mode, the clock will display 24-hour time (22:00).
Setup Menu
Press and hold AUDIO/MENU for more than 3 seconds to
access the setup menu, then press AUDIO/MENU to cycle
through menu options. When desired option appears in the
display, rotate the volume knob left/right to adjust or activate
the desired function.
Setup Menu
Menu Function
Tuner Frequency
Spacing
Options
Action
FREQ USA
Programs unit to USA tuner spacing.
(200kHz for FM and 10kHz for AM)
FREQ EUR
Programs unit to European tuner spacing.
(50kHz for FM and 9kHz for AM)
Clock
Display
CLK OFF
Programs unit to not display the clock when the power is off.
CLK ON
Programs unit to display the clock when the power is off.
Auxiliary
Input
AUX ON
Enables the front panel 3.5mm auxiliary input.
AUX OFF
Disables the auxiliary input.
BEEP OFF
Disables the confirmation beep.
BEEP ON
Enables the confirmation beep.
Beep Confirmation
Local/Distance
Tuning
Power on Message
Demonstration
Mode
LOCAL OFF
Activates distance tuning.
LOCAL ON
Activates local tuning for strong station reception only.
MSG OFF
Disables power on message.
MSG ON
Enables power on message to be displayed.
DEMO OFF
Disables the demonstration mode. DEMO ON
Enables the scrolling demonstration message.
7
XD6150 OPERATION
General Operation
Audio
Press AUDIO/MENU momentarily to select between Volume
(default), Bass, Treble, Balance and Fader.
VOLUME
BASS
TREBLE
BALANCE
FADER
Bass
Press AUDIO/MENU until BAS appears. Rotate the volume
knob left/right to adjust (-6 minimum / +6 maximum).
Treble
Press AUDIO/MENU until TRE appears. Rotate the volume
knob left/right to adjust ( -6 minimum / +6 maximum).
Note: Any adjustment to the Bass or Treble settings
automatically cancels the current EQ curve (if one is
selected).
Note: Bass and Treble settings are retained for each mode
individually.
Balance
Fader
Preset EQ Curves
Loudness
8
Press AUDIO/MENU until BAL appears. Rotate the volume
knob left or right to direct the sound output to the left or right
(BAL L12 - BAL R12). BAL 00 represents equal balance.
Press AUDIO/MENU until FAD appears. Rotate the volume
knob left or right to direct the sound output to the front or
rear (FAD F12 - FAD R12). FAD 00 represents equal fader.
Press EQ•LOUD to select between POP, JAZZ, CLASSIC,
BEAT, ROCK and FLAT (default) equalization curves. Any
adjustment to the Bass or Treble settings automatically
cancels the current EQ curve (if one is selected).
Press and hold EQ•LOUD for 3 seconds to activate the
loudness function. Activating this feature will enhance the
bass and treble frequencies when listening to music at low
volumes.
XD6150 OPERATION
Seek Tuning
Manual Tuning
Band
Storing and Recalling
Station Presets
Preset Scan
Automatic Station Store
AM/FM Tuner Operation
Press TUNE nn or TUNE ll for more than one second to
seek the next strong station.
nn
ll
Press TUNE
or TUNE
momentarily to move radio
frequency up or down one step at a time. Press and hold to
advance quickly.
Press BAND to select between FM1, FM2, FM3, AM1 and AM2
bands.
Up to 18 FM stations and 12 AM stations can be stored. To
store a station, select the desired band and station. Press
and hold the desired preset button (1-6) for more than two
seconds. When stored, the preset number will appear in the
display. The station can be recalled anytime by pressing the
corresponding preset button.
Press AS•PS momentarily to scan presets 1-6 on the current
band, pausing for five seconds at each. Press AS•PS again
to cancel.
Press AS•PS or more than two seconds to automatically
store the six strongest stations to the 1-6 preset buttons in
the current band. Press AS•PS again to cancel.
9
XD6150 OPERATION
CD Player Operation
Insert CD
With the label facing up, insert a standard size CD into the CD
slot. The CD will automatically begin playback.
Eject CD
Press EJECT to eject the CD. The unit will change to previous
mode of operation (AM/FM or AUX). If the disc is not removed
within 10 seconds, the unit will reload the disc. The unit does
not have to be turned on to eject CD.
Track Select
Press TRACK
to skip to the beginning of the next track.
Press TRACK
to return to the beginning of the current
track. Pressing TRACK
again skips to the beginning of
the previous track.
Fast Forward and
Reverse
ll
nn
Press and hold TRACK
or reverse a track.
nn
ll or TRACK nn to fast forward
temporarily stop CD playback.
ll// IIII toagain
to resume playback.
Pause
Press
Press
Repeat
Press RPT to continuously repeat the selected track.
Press RPT again to cancel.
Random
Intro
CD-R/RW Compatibility
Press RDM to play all tracks in random order.
Press RDM again to cancel.
Press INT to play the first 10 seconds of each track.
Press INT again to cancel.
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method.
In addition, the following CDs may be incompatible with
this unit: CDs exposed to extreme temperatures or direct
sunlight for extended periods of time, CDs recorded in which
a recording session failed or a re-recording was attempted
and encrypted or copy-protected CDs that do not conform to
the audio CD-DA red book recording standard.
Note: CD-R/RW recording sessions must be closed (finalized)
for playback.
10
XD6150 OPERATION
Troubleshooting - General
Problem
Cause
Yellow wire not connected or incorrect
Unit will not turn
voltage. Red wire not connected or
on incorrect voltage
(no power)
Black wire not connected
Fuse blown
Speaker wires not connected
Unit has power One or more speaker wires touching
(but no sound)
each other or touching chassis ground
Yellow or red wire touching chassis
ground
Unit blows fuses
Speaker wires touching chassis ground
Incorrect fuse rating
Unit is not mounted correctly or
backstrap is not secure
Excessive skipping
Physical defect in media (CD, CD-R or
CD-RW)
ERROR-01 appears Disc read error
on display
ERROR-02 appears Focus error or disc is in upside down
on display
CD mechanism position out of
Unit will not accept alignment
a disc
CD transit screws still in place
Action
Check connections for proper
voltage (11~16VDC)
Check connection to ground
Replace fuse
Check connections at speakers
Insulate all bare speaker wires
from each other and chassis ground
Check for pinched wire
Check for pinched wire
Use fuse with correct rating
Check mounting sleeve and
backstrap support
Check media for scratches
Press EJECT or RESET
Press EJECT or RESET
Press and hold EJECT for 3
seconds to reset CD mechanism
position
emove 2 transit screws located on
R
top of the unit
11
XD6150 WARRANTY
Limited One Year Warranty
This warranty gives you specific legal rights.
You may also have other rights which vary from
state to state.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
material and workmanship for a period of one
year from the date of the original purchase.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
in material or workmanship or to furnish an
equal new, renewed or comparable product
(whichever is deemed necessary) in exchange
without charges, subject to verification of the
defect or malfunction and proof of the date of
purchase. Subsequent replacement products
are warranted for the balance of the original
warranty period.
Who is covered? This warranty is extended to
the original retail purchaser for products
purchased and used in the U.S.A.
What is covered? This warranty covers all
defects in material and workmanship in this
product. The following are not covered:
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
line voltage, unauthorized repair or failure to
follow instructions supplied with the product,
or damage occurring during return shipment of
the product.
12
What to do?
1. Before you call for service, check the
troubleshooting guide in your owner’s
manual. A slight adjustment of any custom
controls may save you a service call.
2. If you require service during the warranty
period, you must carefully pack the product
(preferably in the original package) and ship
it by prepaid transportation with a copy of the
original receipt from the retailer to an
authorized service center.
3. Please describe your problem in writing and
include your name, a return UPS shipping
address (P.O. Box not acceptable), and a
daytime phone number with your shipment.
4. For more information and for the location of
the nearest authorized service center please
contact us by one of the following methods:
• Call us toll-free at 1-866-382-5476
• E-mail us at cs@dualav.com
Exclusion of Certain Damages: This warranty
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
is authorized to assume for the company any
other liability in connection with the sale of
this product. In no event shall the company be
liable for indirect, incidental or consequential
damages.
XD6150 OPERATION
Specifications
CD Player
Frequency response: 10Hz-20kHz
Channel separation @ 1kHz: >65dB
D/A converter: 1 Bit
FM Tuner
Tuning range: 87.5MHz-107.9MHz
Usable sensitivity: 8.5dBf
50dB quieting sensitivity: 10dBf
Stereo separation @ 1kHz: 40dB
Frequency response: 30Hz-13kHz
AM Tuner
Tuning range: 530kHz-1710kHz
Usable sensitivity: 22uV
Frequency response: 30Hz-2.2kHz
General
Operating voltage: 11-16 VDC, negative ground
Speaker output impedance: 4~8 ohms
Line output voltage: 2 Volts RMS
Dimensions: 7" x 2" x 7" (178 x 51 x 178 mm)
Design and specifications subject to change without notice.
CEA-2006 Power Standard Specifications
(reference: 14.4VDC +/- 0.2V, 20Hz~20kHz)
Power Output: 17 Watts RMS x 4 channels at 4 ohms and < 1% THD+N
Signal to Noise Ratio: 80dBA (reference: 1 watt into 4 ohms)
13
XD6150 OPERATION
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
14
XD6150 NOTES
15
Dual Electronics Corp.
Toll Free: 1-866-382-5476
www.dualav.com
©2009 Dual Electronics Corp. All rights reserved.
Other trademarks and trade names are those of their respective owners.
NSA0509-V01
Download PDF