Converters.TV | 901 | VLINX ESR901 Converter Installation + Configuration

VLINX ESR901 Converter
Installation & Configuration Manual
Updated 2013.08.05
VLINX ESR901 Converter Installation & Configuration
Copyright  2013  AMS Controls, Inc. All rights reserved.
The information contained in this document is proprietary to AMS Controls, Inc., and is not to be
reproduced in any form without the specific written authorization of AMS Controls, Inc.
AMS Controls, Inc. reserves the right to change the contents of this manual without customer notice or
permission. The procedures described in this handbook must be performed only by trained, certified
industrial electricians in accordance with local, state, federal, and NEC codes and regulations. While
AMS Controls has taken all reasonable care to develop safe procedures, it accepts no responsibility for
misprints, or for injuries, damages, death, or destruction to persons or equipment caused as a result of
not closely following these instructions. For specific controller questions, contact AMS Controls Inc.
The most current version of this manual is always available at: http://www.amscontrols.com
AMS Controls, Inc.
12180 Prichard Farm Road
Maryland Heights, MO 63043
314.344.3144 – 1-800-334-521 (US & Canada) – fax: 314.344.9996 – support@amscontrols.com
www.amscontrols.com
2
VLINX ESR901 Converter Installation & Configuration
Table of Contents
CHAPTER 1:
INSTALLING THE VLINX ESR901 CONVERTER .................................................... 1
INTRODUCTION ................................................................................................................................ 1
INSTALLING THE VLINX ESR901 CONVERTER ....................................................................................... 1
CHAPTER 2:
CONFIGURE THE VLINX ESR901 CONVERTER .................................................... 4
CHAPTER 3:
CONFIGURE ECLIPSE TO COMMUNICATE WITH THE VLINX ESR901 CONVERTER 8
DEFINE DEVICE COMM PORTS FOR ECLIPSE ......................................................................................... 8
DEFINE THE MACHINE ECLIPSE ASSOCIATES WITH THE DEVICE................................................................. 10
APPENDIX A:
GLOSSARY ................................................................................................. 14
APPENDIX B:
RS-485 CONNECTIONS ............................................................................... 15
INDEX .................................................................................................................................. 16
i
VLINX ESR901 Converter Installation & Configuration
Chapter 1: Installing the VLINX
ESR901 Converter
Introduction
The VLINX ESR901 Converter (ESR901) enables RS-485 devices to communicate with an
Ethernet network.
Installing the VLINX ESR901 Converter

DANGER: Always follow proper Lockout/Tagout procedure to avoid
potentially lethal electric shock!
To install the ESR901,
1. Mount the ESR901 inside the control panel that houses the XL200 series
controller.
2. The ESR901 should be connected to the same 24 VDC power supply as the
XL200 series controller’s CPU. Connect the wire from the power supply’s -24
VDC terminal to the converter’s GND terminal.
3. Connect the wire from the power supply’s -24 VDC terminal to the converter’s
AC/DC+ N terminal.
4.
Set the converter’s DIP switches:
A. Switch DIP switch 1 (Run) to OFF.
B. Switch DIP switch 2 (Terminal) to ON.
1
VLINX ESR901 Converter Installation & Configuration
5. Connect a cable containing a twisted pair from the Controller to the converter.
AMS recommends unshielded CAT 5 for this cable:
A. Connect a wire from one pair to the converter’s CTS/TX- terminal, and to
the XL200 series controller at terminal B11.
B. Connect the other wire from the same pair to the converter’s TX/TX+
terminal, and to the XL200 series controller at terminal B10.
Figure 1: The cable with twisted pair wires, connected
2
VLINX ESR901 Converter Installation & Configuration
6. Connect the network Ethernet cable to the converter’s Ethernet port.
Figure 2: The VLINX ESR901 Converter installed in the control panel
The VLINX ESR901 Converter is installed.
3
VLINX ESR901 Converter Installation & Configuration
Chapter 2: Configure the VLINX
ESR901 Converter
Once the VLINX ESR901 Converter (ESR901) is installed, it must be configured. To
configure the ESR901,
1. Install the VLINX ESP Manager software.
2. Select Start – All Programs – B&B Electronics – VLINX – ESP Servers – VLINX
ESP Manager. The VLINX ESP Manager screen displays, showing all available
serial servers.
Figure 3: The VLINX ESP Manager screen
4
VLINX ESR901 Converter Installation & Configuration
3. From the list, double click the name of the server you want to configure for the
ESR901. The Server Properties screen displays:
Figure 4: The Server Properties screen
4. Change the server properties as required:
Field
Setting

Server Name
Enter a descriptive name for the server.

Serial Number
Displays the serial number of the server.

Password
If desired, enter a password to restrict access to this page.

DHCP
See your Network Administrator for specific, appropriate settings.

IP Address
See your Network Administrator for specific, appropriate settings.

Netmask
See your Network Administrator for specific, appropriate settings.

Gateway
See your Network Administrator for specific, appropriate settings.

MAC Address
Displays the MAC Address for the server.

Version & Date
Displays the version and date of the server software.

Link Status
Displays the Ethernet network speed.
5
VLINX ESR901 Converter Installation & Configuration

Hardware ID
Display only.

Serial Port
Select 1

Baud Rate
See your Network Administrator for specific, appropriate settings.

Data/Stop Bits
Select 8-1

Parity
Select Even

Flow Control
Select None

Protocol
Select TCP

Serial Timeout
Enter 0

TCP Alive
Timeout
Enter 0

Connection
Mode
Select Server

Delimiter HEX 1
Enter 03

Delimiter HEX 2
Enter 00

Force Transmit
Enter 65535

Port Status
Display only

TCP/UDP Port
Enter 4000

Serial Port
Mode
Select RS485H

Connection at
Display only

Maximum
connection
Select 8

Remote IP
Address
Enter 255.255.255.255
5. Click [Update]. The Restart pop-up window displays.
Figure 5: Restart pop-up window
6
VLINX ESR901 Converter Installation & Configuration
6. Click [Yes]. The serial server begins to re-start. When it’s finished, the programs
prompts you, asking if you want to search all reachable servers again.
7. Click [No] (generally, it’s unnecessary to search a second time).
8. Close the VLINX ESP Manager window. The configuration is complete.
7
VLINX ESR901 Converter Installation & Configuration
Chapter 3: Configure Eclipse to
Communicate with the VLINX
ESR901 Converter
Once the VLINX ESR901 Converter (ESR901) is installed and configured, the Eclipse
software must be configured to communicate with the converter.
To configure Eclipse to communicate with the ESR901, first define the device’s COMM
ports for Eclipse and then define the machine Eclipse should associate with the device.
Define Device COMM Ports for Eclipse
1. Start Eclipse. The Eclipse window displays.
Figure 6: The Eclipse window
8
VLINX ESR901 Converter Installation & Configuration
2. Verify that Eclipse-COMM is not running.
- If the large button at the upper-right of the window displays [START
ECLIPSE-COMM], Eclipse-COMM is already off.
- If the large button at the upper-right of the window displays [ECLIPSECOMM IS RUNNING] Eclipse-COMM is on.
Click the button to bring the window forward.
Click the close button
to close the Eclipse window and shut Eclipse off.
3. Select Maintenance – COMM Port Definitions. The COMM Port Definitions
window displays.
Figure 7: The COMM Port Definitions window
4. Click [Add]. The first line is highlighted.
Note: If there are already records displayed when the window opens, the pop-up
window prompts to ask if you want to use the highlighted record as a base for the
new record.
- Click [Yes] to start with a partially-filled line.
- Click [No] to start with a completely blank line.
5. In the Port Name field, enter a unique name for the device you’re adding.
6. From the Adapter Type drop-down listbox, select the B&B Ethernet.
7. From the Port drop-down listbox, select IP Address.
8. In the IP Address field, enter the device’s IP Address.
9. From the Baud Rate drop-down listbox, select the appropriate baud rate for
communicating with the new device.
10. Skip the Setting field—it’s prefilled.
9
VLINX ESR901 Converter Installation & Configuration
11. Checkmark the Active checkbox to indicate the device is operating. Uncheck it if
the device is not operating (for example, if you are installing and configuring it
now but not planning to put it into service until later).
12. Skip the Echo On checkbox—it auto selects based on the Adapter Type selected
later.
13. Skip the Config Port checkbox—it auto selects based on the Adapter Type
selected later.
14. Skip the COMM Group drop-down listbox.
15. Click [Save]. The device you set up is saved in the system.
16. Repeat steps 4-15 for each additional device you are adding.
17. Click [Close]. The COMM port is defined.
Define the Machine Eclipse Associates with the Device
1. Open Maintenance – Machine Definitions. The Machine Definitions window
displays:
Figure 8: Machine Definitions window
Note: If no machines are already defined when Eclipse starts, Eclipse
automatically adds and displays Machine 1 in this form.
2. If no line displays for the desired machine, click [ADD] to start a new line for the
machine definition.
10
VLINX ESR901 Converter Installation & Configuration
3. In the Machine Description field, enter a unique name for the machine.
4. Checkmark Active if the device is active.
5. In the Machine ID field, enter a unique ID number for the machine. The ID
number must match the network ID number assigned to the Controller.
6. From the COMM Port drop-down listbox, select the COMM port for this
machine’s device.
7. Skip the following fields:
- Machine Group
- Clear Shift
- Min. Footage field
- First Shift
- Second Shift
- Third Shift
- Default Times
- Disable Open Request
- No Punch Parts
- Coil Print Port
- Bundle by Wgt
- Network Printer
- Network Printer
- Ascending
- Descending
- Natural
- Pattern Hrs
8. Click [Save]. The information for the device is saved.
9. Click [Close].
10. Click [Start Eclipse-COMM]. The Eclipse-COMM window displays.
11
VLINX ESR901 Converter Installation & Configuration
Figure 9: The Eclipse-COMM window
11. Verify that the port’s status is OPEN (i.e., its line is green).
-
If the port is not OPEN, click the Disabled checkbox to see if the port opens.
If it still does not open after that, there is something wrong in either the
ESR901 set up or in the Network connection.
12. Minimize the Eclipse-COMM window. The Eclipse window displays.
13. Verify Eclipse is operating correctly.
12
-
If Eclipse is communicating with the new device, the circles under Visual
Status will display as red or green (see Figure 10).
-
If it’s not communicating, both circles are grey (see Figure 6).
VLINX ESR901 Converter Installation & Configuration
Figure 10: The Eclipse Window (Eclipse-COMM on and running)
14. Minimize Eclipse. The installation and configuration is complete.
13
VLINX ESR901 Converter Installation & Configuration
Appendix A:
Glossary
Converter
A device that enables other devices to communicate with an Ethernet network.
Device
A unit of hardware, outside the essential computer (processor, memory, and data
paths), that can provide input, receive output, or both.
Eclipse
Production management software that links production scheduling to the shop floor. It
automatically downloads orders, uploads production data and monitors machines in
real time while assembling the data into detailed reports.
VLINX ESR901 Converter
A device that enables RS-485 devices to communicate with an Ethernet network.
14
VLINX ESR901 Converter Installation & Configuration
Appendix B: RS-485
Connections
DB-9 Male
outside
RS-485 Signal Name
Direction
RS-485
DB9M Pin
Data B (+)
In/Out
DATA B (+)
3
Data A (-)
In/Out
DATA A (-)
4
---
GND
5
Signal Ground
15
VLINX ESR901 Converter Installation & Configuration
Index
B
Belden cable, 2
C
Comm Port Definitions window, 8
COMM Ports, 7
Communicate with the VLINX ESR901
Converter, 7
Configure Eclipse to Communicate with
the VLINX ESR901 Converter, 7
G
Glossary, 13
I
Install the VLINX ESR901 Converter, 1
Introduction, 1
M
Machine Definitions window, 9
P
power supply, 1
Configure the VLINX ESR901 Converter,
4
D
Define Device COMM Ports for Eclipse,
7
Define the Machine Eclipse Associates
with the Device, 9
R
RS-485 Connections, 14
S
server properties, 5
V
Visual Status, 11
E
Eclipse, 7, 9
Eclipse-COMM, 8
VLINX ESP Manager software, 4
VLINX ESR901 Converter, 1, See
Configure, 4
Ethernet cable, 3
Install, 1
16
Download PDF