Belkin | 2.0 RELEASE NOTES | User manual | Belkin 2.0 RELEASE NOTES User manual

INTRODUCTION
Congratulations and thank you for
purchasing the MiniWireless Optical Mouse
from Belkin. You are about to experience
a whole new world of computing
convenience with superior input features
and navigating accuracy. The MiniWireless
Optical Mouse provides a great radio
frequency (RF) wireless input solution for
the mobile professional.
SYSTEM REQUIREMENTS
PC 486 or higher
Windows® 98 SE, Me, 2000, XP
USB port
CD-ROM drive
PACKAGE INCLUDES
MiniWireless Optical Mouse
USB Receiver
User Manual
2 AAA Batteries
OVERVIEW
Before starting the installation of the
hardware for the Mouse, please remove any
drivers or software from any mice that were
previously installed on your computer. This is
to avoid any conflicts they may create, which
could result in an improper installation of
your Mouse. Please consult the documents
that came with your previous mouse for
proper instructions on how to uninstall the
software and drivers.
MOUSE SETUP
1. Remove the top cover of your Mouse by
pressing and holding the bottom release
tab. (Fig. 1)
Fig. 1
2. Insert 2 AAA batteries. (Fig. 2)
HARDWARE INSTALLATION
1. Make sure your computer is turned on
before installing the Mouse.
2. Connect the receiver into an available
USB port on your PC. (Fig. 3)
Navigate your notebook computer with
optical precision and wireless freedom
Fig. 3
3. Your PC should automatically find new
hardware and install necessary drivers.
Note: Windows 98 SE may require you to
insert your Windows 98 SE Installation
CD into your computer’s CD-ROM drive to
complete the install.
4. Switch on the power of the Wireless
Mouse located on the backside of the
Mouse. The Mouse syncs with the
receiver automatically. (Fig. 4)
User Manual
F8E874
P74749-A
Fig. 4
Note: If the Mouse does not sync with
the receiver automatically, please see
the section entitled “Synchronizing your
Mouse to your Receiver”, below.
Note: While traveling, please switch off
the unit to save battery power.
SYNCHRONIZING YOUR MOUSE TO
YOUR RECEIVER
If the Mouse does not automatically sync
with the receiver, press the connect button
on the top of the receiver. The light on the
receiver will blink rapidly. Then sync the
Mouse to the receiver by pushing the sync
button on the bottom of the Mouse. The
light on the receiver will stop blinking and
light brightly. (Fig. 5)
Fig. 2
3. Replace the top cover and close.
Note: Be sure to check polarity (+ or
– sign) and insert battery properly.
MiniWireless
Optical Mouse
Fig. 5
Note: Each time you repeat this step, the
Mouse randomly selects a new ID. This
allows multiple wireless mice to work in
the same location without cross talk. If
you experience cross talk with another
wireless mouse, repeat the synchronizing
steps to change the channel.
SETUP FOR MULTIPLE USERS
When using more than one MiniWireless
Optical Mouse in the same location, set up
one Mouse at a time. You must complete the
setup for each Mouse before beginning to
set up the next Mouse.
ENVIRONMENT
To avoid environment interference, which
will shorten the effective operation distance,
please note the following:
1. Do not put the Mouse and receiver on
a metal cabinet or desk. Metal creates
RF interference, which may impair the
RF communication and shorten the
communication distance.
2. Keep a distance of more than 4.9 feet
(1.5m) between your Mouse and
another operational RF device to
avoid interference.
3. The optical sensor of the Mouse will
not work correctly if placed on a mirror,
glass, or on any reflecting or half-tone
painted surface.
TROUBLESHOOTING
The cursor doesn’t react when I move
the Mouse.
1. This is probably because the distance
between the receiver and Mouse exceeds
the working range of 3.3 feet (1m). Adjust
so that the Mouse is closer to the receiver.
2. Make sure that the Mouse is not placed
on a reflective surface such as a mirror,
glass, half-tone painted surface, or on a
3-D mouse pad. When using the wireless
device on a metal table or near metal
furniture, use a non-reflective, thick
mouse pad to reduce the potential
for interference.
3. Your synchronizing setup may not have
worked properly. Please repeat the
synchronization setup process.
Why don’t the scroll functions work with my
notebook computer?
Check to be sure that you have disabled
your notebook computer’s trackball, touch
pad, or J-Key in the Control Panel. Then
enable the external port so that all your
Mouse’s functions will be available.
My USB Mouse was not detected by the
system and won’t work. What should I do?
Please do the following:
1. Ensure that your USB Mouse is
completely plugged into the USB port.
2. Check the functioning of your system’s
USB port in the “Device Manager” page
of System Properties. If there is a circled
exclamation point through the USB
port’s icon, the USB controller has a
problem. Please try to uninstall and
then reinstall the USB driver, or contact
your PC manufacturer’s technical
support department.
3. Check the version of your operating
system. If you are not running Windows
98 SE, Me, 2000, or XP, please update
your operating system to one of these, so
that the USB device can be enabled.
4. Make sure that the USB port is enabled in
the BIOS setup.
FCC/CE Statement
DECLARATION OF CONFORMITY WITH FCC RULES
FOR ELECTROMAGNETIC COMPATIBILITY
We, Belkin Corporation, of 501 West Walnut Street,
Compton, CA 90220, declare under our sole responsibility
that the product, F8E874, to which this declaration relates,
complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Caution: Exposure to Radio Frequency Radiation.
The radiated output power of this device is far below the
FCC radio frequency exposure limits. Nevertheless, the
device shall be used in such a manner that the potential for
human contact during normal operation is minimized.
When connecting an external antenna to the device,
the antenna shall be placed in such a manner to minimize
the potential for human contact during normal operation.
In order to avoid the possibility of exceeding the FCC
radio frequency exposure limits, human proximity to the
antenna shall not be less than 20cm (8 inches) during
normal operation.
Federal Communications Commission Notice
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio
frequency energy. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try and correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and
the receiver.
• Connect the equipment to an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
THE WARRANTY AND REMEDIES SET FORTH ABOVE
ARE EXCLUSIVE IN LIEU OF ALL OTHERS, WHETHER
ORAL OR WRITTEN, EXPRESSED OR IMPLIED. BELKIN
SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED
WARRANTIES, INCLUDING, WITHOUT LIMITATION,
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
No Belkin dealer, agent, or employee is authorized to make
any modification, extension, or addition to this warranty.
BELKIN IS NOT RESPONSIBLE FOR SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES
RESULTING FROM ANY BREACH OF WARRANTY, OR
UNDER ANY OTHER LEGAL THEORY, INCLUDING
BUT NOT LIMITED TO LOST PROFITS, DOWNTIME,
GOODWILL, DAMAGE TO OR REPROGRAMMING, OR
REPRODUCING ANY PROGRAM OR DATA STORED IN
OR USED WITH BELKIN PRODUCTS.
Some states do not allow the exclusion or limitation of
incidental or consequential damages or exclusions of
implied warranties, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights that vary from
state to state.
Modifications
The FCC requires the user to be notified that any changes
or modifications to this device that are not expressly
approved by Belkin Corporation may void the user’s
authority to operate the equipment.
Canada-Industry Canada (IC)
The wireless radio of this device complies with RSS 210
Industry Canada. This Class B digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la classe B conforme á la norme
NMB-003 du Canada.
Belkin Corporation Limited Lifetime Product Warranty
Belkin Corporation warrants this product against defects
in materials and workmanship for its lifetime. If a defect
is discovered, Belkin will, at its option, repair or replace
the product at no charge provided it is returned during the
warranty period, with transportation charges prepaid, to
the authorized Belkin dealer from whom you purchased the
product. Proof of purchase may be required.
This warranty does not apply if the product has been
damaged by accident, abuse, misuse, or misapplication;
if the product has been modified without the written
permission of Belkin; or if any Belkin serial number has
been removed or defaced.
Belkin Tech Support
US: 800-223-5546 ext. 2263
310-898-1100 ext. 2263
Europe: 00 800 223 55 460
Australia: 1800 235 546
New Zealand: 0800 235 546
Belkin Corporation
501 West Walnut Street
Compton, CA 90220-5221
USA
310-898-1100
310-898-1111 fax
Belkin Ltd.
Express Business Park
Shipton Way, Rushden, NN10 6GL
United Kingdom
+44 (0) 1933 35 2000
+44 (0) 1933 31 2000 fax
Belkin Ltd.
7 Bowen Crescent
West Gosford, NSW 2250
Australia
+61 (0) 2 4372 8600
+61 (0) 2 4372 8603 fax
Belkin B.V.
Boeing Avenue 333
1119 PH Schiphol-Rijk
The Netherlands
+31 (0) 20 654 7300
+31 (0) 20 654 7349 fax
© 2005 Belkin Corporation. All rights reserved. All trade names are
registered trademarks of respective manufacturers listed.
Download PDF