Sharp | CD-XP200W | Owner`s manual | Sharp CD-XP200W Owner`s manual

BL03701-101
DIGITAL CAMERA
FINEPIX XP200 Series
Owner’s Manual
Thank you for your purchase
of this product. This manual
describes how to use your
FUJIFILM digital camera and the
supplied software. Be sure that
you have read and understood
its contents and the warnings
in “For Your Safety” (P ii) before
using the camera.
For information on related products, visit our website at
http://www.fujifilm.com/products/digital_cameras/index.html
EN
Before You Begin
First Steps
Basic Photography and Playback
More on Photography
More on Playback
Wireless Networks
Movies
Connections
Menus
Technical Notes
Troubleshooting
Appendix
For Your Safety
IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions: All the safety and
operating instructions should be read
before the appliance is operated.
• Retain Instructions: The safety and operating
instructions should be retained for future
reference.
• Heed Warnings: All warnings on the
appliance and in the operating instructions
should be adhered to.
• Follow Instructions: All operating and use
instructions should be followed.
Installation
Power Sources: This video product should
be operated only from the type of power
source indicated on the marking label. If you
are not sure of the type of power supply to
your home, consult your appliance dealer or
local power company. For video products
intended to operate from battery power,
or other sources, refer to the operating
instructions.
Grounding or Polarization: This video product
is equipped with a polarized alternatingcurrent line plug (a plug having one blade
wider than the other). This plug will fit into
the power outlet only one way. This is a safety
feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If
the plug should still fail to fit, contact your
electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the
polarized plug.
ii
Alternate Warnings: This video product is
equipped with a three-wire grounding-type
plug, a plug having a third (grounding) pin.
This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you
are unable to insert the plug into the outlet,
contact your electrician to replace your
obsolete outlet. Do not defeat the safety
purpose of the grounding type plug.
Overloading: Do not overload wall outlets and
extension cords as this can result in a risk of
fire or electric shock.
Power-Cord Protection: Power-supply cords
should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit
from the appliance.
Accessories: Do not place this video product
on an unstable cart, stand, tripod, bracket, or
table. The video product may fall, causing
serious injury to a child or adult, and serious
damage to the appliance. Use only with a
cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold
with the video product. Any mounting of the
appliance should follow the manufacturer’s
instructions, and should use a mounting
accessory
recommended
by
the
manufacturer.
Ventilation: Slots and openings in the cabinet
are provided for ventilation, to ensure reliable
operation of the video product and to protect
it from overheating, and these openings must
not be blocked or covered. The openings
should never be blocked by placing the video
product on a bed, sofa, rug, or other similar
surface.
An appliance and cart
This video product should not be placed in combination should
a built-in installation such as a bookcase or be moved with care.
rack unless proper ventilation is provided or Quick stops, excessive
the manufacturer’s instructions have been force, and uneven
adhered to. This video product should never surfaces may cause
be placed near or over a radiator or heat the appliance and cart
combination to overturn.
register.
Attachments: Do not use attachments
not recommended by the video product
manufacturer as they may cause hazards.
Water and Moisture: Do not use this video
product near water—for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub,
in a wet basement, or near a swimming pool,
and the like (excluding waterproof products).
For Your Safety
Antennas
Outdoor Antenna Grounding: If an outside
antenna or cable system is connected to
the video product, be sure the antenna or
cable system is grounded so as to provide
some protection against voltage surges and
built-up static charges. Section 810 of the
National Electrical Code, ANSI/NFPA No. 70,
provides information with respect to proper
grounding of the mast and supporting
structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding
conductors, location of antenna discharge
unit, connection to grounding electrodes,
and requirements for the grounding
electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
Ground Clamp
Antenna Lead
in Wire
Electric Service
Equipment
Antenna
Discharge Unit
(NEC SECTION
810-20)
Ground Clamps
If the video product does not operate
normally follow the operating instructions.
Adjust only those controls that are covered
by the operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive work
Object and Liquid Entry: Never push objects by a qualified technician to restore the video
of any kind into this video product through product to its normal operation.
openings as they may touch dangerous
voltage points or short out parts that could When the video product exhibits a distinct
result in a fire or electric shock. Never spill change in performance—this indicates a
liquid of any kind on the video product need for service.
Use
Cleaning: Unplug this video product from the
wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
(excluding waterproof products).
Lightning: For added protection for this video
product receiver during a lightning storm, or
when it is left unattended and unused for long
periods of time, unplug it from the wall outlet
and disconnect the antenna or cable system.
This will prevent damage to the video product
due to lightning and power-line surges.
Replacement Parts: When replacement
parts are required, be sure the service
technician has used replacement parts
specified by the manufacturer or have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock or other hazards.
Safety Check: Upon completion of any service
or repairs to this video product, ask the
Service
service technician to perform safety checks to
Servicing: Do not attempt to service this video determine that the video product is in proper
product yourself as opening or removing operating condition.
covers may expose you to dangerous voltage
or other hazards. Refer all servicing to
qualified service personnel.
Grounding
Damage Requiring Service: Unplug this
Conductors
video product from the wall outlet and refer
(NEC SECTION
servicing to qualified service personnel under
810-21)
the following conditions:
• When the power-supply cord or plug is
Power Lines: An outside antenna system should
damaged.
not be located in the vicinity of overhead • If liquid has been spilled, or objects have
power lines or other electric light or power
fallen into the video product.
circuits, or where it can fall into such power • If the video product has been exposed
lines or circuits. When installing an outside
to rain or water (excluding waterproof
antenna system, extreme care should be taken
products).
to keep from touching such power lines or • If the video product has been dropped or
circuits as contact with them might be fatal.
the cabinet has been damaged.
Power Service Grounding
Electrode System (NEC ART
250. PART H)
iii
For Your Safety
Be sure to read these notes before use
WARNING
Safety Notes
• Make sure that you use your camera correctly. Read these safety
notes and your Owner’s Manual carefully before use.
• After reading these safety notes, store them in a safe place.
About the Icons
The icons shown below are used in this document to indicate the
severity of the injury or damage that can result if the information
indicated by the icon is ignored and the product is used incorrectly
as a result.
WARNING
CAUTION
This icon indicates that death or serious injury can result if the
information is ignored.
This icon indicates that personal injury or material damage can
result if the information is ignored.
The icons shown below are used to indicate the nature of the
instructions which are to be observed.
Triangular icons tell you that this information requires
attention (“Important”).
Circular icons with a diagonal bar tell you that the action
indicated is prohibited (“Prohibited”).
Filled circles with an exclamation mark indicate an action that
must be performed (“Required”).
WARNING
Unplug from
power socket
iv
If a problem arises, turn the camera off, remove the battery, and
disconnect and unplug the AC power adapter. Continued use of
the camera when it is emitting smoke, is emitting any unusual
odor, or is in any other abnormal state can cause a fire or
electric shock. Contact your FUJIFILM dealer.
Do not allow water or foreign objects to enter the camera. If water
or foreign objects get inside the camera, turn the camera off,
remove the battery, and disconnect and unplug the AC power
adapter. Continued use of the camera can cause a fire or
electric shock. Contact your FUJIFILM dealer.
Do not use in
the bathroom or
shower
Do not
disassemble
Do not touch
internal parts
Do not use the camera in the bathroom or shower (excluding
waterproof products). This can cause a fire or electric shock.
Never attempt to change or take apart the camera (never open
the case). Failure to observe this precaution can cause fire or
electric shock.
Should the case break open as the result of a fall or other accident,
do not touch the exposed parts. Failure to observe this precaution
could result in electric shock or in injury from touching the
damaged parts. Remove the battery immediately, taking care
to avoid injury or electric shock, and take the product to the
point of purchase for consultation.
Do not change, heat or unduly twist or pull the connection cord and
do not place heavy objects on the connection cord. These actions
could damage the cord and cause a fire or electric shock. If the
cord is damaged, contact your FUJIFILM dealer.
Do not place the camera on an unstable surface. This can cause the
camera to fall or tip over and cause injury.
Never attempt to take pictures while in motion. Do not use the
camera while you are walking or driving a vehicle. This can
result in you falling down or being involved in a traffic accident.
Do not touch any metal parts of the camera during a thunderstorm.
This can cause an electric shock due to induced current from
the lightning discharge.
Do not use the battery except as specified. Load the battery as
shown by the indicator.
Do not heat, change or take apart the battery. Do not drop or subject
the battery to impacts. Do not store the battery with metallic
products. Any of these actions can cause the battery to burst or
leak and cause fire or injury as a result.
Use only the battery or AC power adapters specified for use with this
camera. Do not use voltages other than the power supply voltage
shown. The use of other power sources can cause a fire.
If the battery leaks and fluid gets in contact with your eyes, skin or
clothing, flush the affected area with clean water and seek medical
attention or call an emergency number right away.
For Your Safety
WARNING
CAUTION
Do not use the charger to charge batteries other than those specified
here. The supplied battery charger is for use only with the type
of battery supplied with the camera. Using the charger to
charge conventional batteries or other types of rechargeable
batteries can cause the battery to leak fluid, overheat or burst.
Do not use the AC power adapter when the plug is damaged or the
plug socket connection is loose. This could cause a fire or electric
shock.
Do not cover or wrap the camera or the AC power adapter in a cloth or
blanket. This can cause heat to build up and distort the casing
or cause a fire.
When you are cleaning the camera or you do not plan to use the
camera for an extended period, remove the battery and disconnect
and unplug the AC power adapter. Failure to do so can cause a
fire or electric shock.
Danger of explosion if battery is incorrectly replaced. Replace only
with the same.
Do not use in the presence of flammable objects, explosive gases,
or dust.
When carrying the battery, install it in a digital camera or keep it
in the hard case. When storing the battery, keep it in the hard case.
When discarding, cover the battery terminals with insulation tape.
Contact with other metallic objects or batteries could cause
the battery to ignite or burst.
Keep memory cards out of the reach of small children. Because
memory cards are small, they can be swallowed by children.
Be sure to store memory cards out of the reach of small
children. If a child swallows a memory card, seek medical
attention or call an emergency number.
CAUTION
Do not use this camera in locations affected by oil fumes or steams.
This can cause a fire or electric shock.
Do not use this camera in locations affected by humidity or dust
(excluding waterproof products). This can cause a fire or electric
shock.
Do not leave this camera in places subject to extremely high
temperatures. Do not leave the camera in locations such as a
sealed vehicle or in direct sunlight. This can cause a fire.
Unplug from
power socket
When charging ends, unplug the charger from the power socket.
Leaving the charger plugged into the power socket can cause
a fire.
Using a flash too close to a person’s eyes may temporarily affect the
eyesight. Take particular care when photographing infants and
young children.
When a memory card is removed, the card could come out of the slot
too quickly. Use your finger to hold it and gently release the card.
Injury could result to those struck by the ejected card.
Request regular internal testing and cleaning for your camera.
Build-up of dust in your camera can cause a fire or electric
shock. Contact your FUJIFILM dealer to request internal
cleaning every two years. Please note that this service is not
free of charge.
Keep out of the reach of small children. This product could cause
injury in the hands of a child.
Do not place heavy objects on the camera. This can cause the
heavy object to tip over or fall and cause injury.
Do not move the camera while the AC power adapter is still
connected. Do not pull on the connection cord to disconnect the AC
power adapter. This can damage the power cord or cables and
cause a fire or electric shock.
v
For Your Safety
■ Charging the Battery
Charge the battery in the supplied battery
charger. Charging times will increase at
ambient temperatures below +10 °C (+50 °F)
or above +35 °C (+95 °F). Do not attempt to
The following describes the proper use charge the battery at temperatures above
of batteries and how to prolong their life. 40 °C (+104 °F); at temperatures below 0 °C
Incorrect use can shorten battery life or cause (+32 °F), the battery will not charge.
leakage, overheating, fire, or explosion.
Do not attempt to recharge a fully charged
Li-ion Batteries
battery. The battery does not however need
Read this section if your camera uses a to be fully discharged before charging.
rechargeable Li-ion battery.
The battery may be warm to the touch
The battery is not charged at shipment. immediately after charging or use. This is
Charge the battery before use. Keep the normal.
battery in its case when not in use.
■ Battery Life
At normal temperatures, the battery can be
■ Notes on the Battery
The battery gradually loses its charge when recharged about 300 times. A noticeable
not in use. Charge the battery one or two decrease in the length of time the battery will
hold a charge indicates that it has reached
days before use.
the end of its service life and should be
Battery life can be extended by turning the replaced.
camera off when not in use.
■ Storage
Battery capacity decreases at low Performance may be impaired if the battery is
temperatures; a depleted battery may not left unused for extended periods when fully
function at when cold. Keep a fully charged charged. Run the battery flat before storing it.
spare battery in a warm place and exchange
as necessary, or keep the battery in your If the camera will not be used for an extended
pocket or other warm place and insert it in period, remove the battery and store it in a
the camera only when shooting. Do not dry place with an ambient temperature of
place the battery in direct contact with hand from +15 °C to +25 °C (+59 °F to +77 °F). Do
not store in locations exposed to extremes of
warmers or other heating devices.
temperature.
The Battery and Power Supply
Note: Check the type of battery used in
your camera and read the appropriate
sections.
vi
■ Cautions: Handling the Battery
• Do not transport or store with metal objects
such as necklaces or hairpins.
• Do not expose to flame or heat.
• Do not disassemble or modify.
• Use with designated chargers only.
• Do not drop or subject to strong physical
shocks.
• Do not expose to water.
• Keep the terminals clean.
• The battery and camera body may become
warm to the touch after extended use. This
is normal.
AA Alkaline/Rechargeable NiMH Batteries/
AA lithium batteries
Read this section if your camera uses
AA alkaline or rechargeable AA NiMH
batteries.
Information on compatible
battery types may be found elsewhere in the
camera manual.
■ Cautions: Handling the Batteries
• Do not expose to water, flame, or heat, or
store in warm or humid conditions.
• Do not transport or store with metal objects
such as necklaces or hairpins.
• Do not disassemble or modify the batteries
or battery casing.
• Do not subject to strong physical shocks.
• Do not use batteries that are leaking,
deformed, or discolored.
• Keep out of reach of infants and small
children.
• Insert in the correct orientation.
For Your Safety
• Do not mix old and new batteries, batteries
with different charge levels, or batteries of
different types.
• If the camera will not be used for an
extended period, remove the batteries.
Note that the camera clock will be reset.
• The batteries may be warm to the touch
immediately after use. Turn the camera
off and allow the batteries to cool before
handling.
• Battery capacity tends to decrease at low
temperatures. Keep spare batteries in a
pocket or other warm place and exchange
as necessary. Cold batteries may recover
some of their charge when warmed.
• Fingerprints and other stains on the battery
terminals can impair battery performance.
Thoroughly clean the terminals with a
soft, dry cloth before inserting them in the
camera.
If the batteries leak, clean the battery
compartment thoroughly before
inserting new batteries.
If fluid from the battery comes into
contact with skin or clothing, flush
the affected area with water. If fluid
enters your eyes, immediately flush
the affected area with water and seek
medical attention. Do not rub your eyes.
Failure to observe this precaution could
result in permanent visual impairment.
■ NiMH Batteries
The capacity of Ni-MH batteries may be
temporarily reduced when new, after long
periods of disuse, or if they are repeatedly
recharged before being fully discharged.
This is normal and does not indicate a
malfunction. Capacity can be increased by
repeatedly discharging the batteries using
the discharge option in the camera setup
menu and recharging them using a battery
charger.
Q CAUTION: Do not use the discharge option
with alkaline batteries.
The camera draws a small amount of current
even when off. Ni-MH batteries that have
been left in the camera for an extended
period may be drawn down to the point
that they no longer hold a charge. Battery
performance may also drop if the batteries
are run down in a device such as a flashlight.
Use the discharge option in the camera setup
menu to discharge Ni-MH batteries. Batteries
that no longer hold a charge even after
repeatedly being discharged and recharged
have reached the end of their service life and
must be replaced.
AC Power Adapters (Available Separately)
This section applies to all camera models.
Use only FUJIFILM AC power adapters
designated for use with this camera. Other
adapters could damage the camera.
• The AC power adapter is for indoor use only.
• Be sure the DC plug is securely connected
to the camera.
• Turn the camera off before disconnecting
the adapter. Disconnect the adapter by the
plug, not the cable.
• Do not use with other devices.
• Do not disassemble.
• Do not expose to high heat and humidity.
• Do not subject to strong physical shocks.
• The adapter may hum or become hot to the
touch during use. This is normal.
• If the adapter causes radio interference,
reorient or relocate the receiving antenna.
Ni-MH batteries can be recharged in a battery
charger (sold separately). Batteries may
become warm to the touch after charging.
Refer to the instructions provided with
the charger for more information. Use the
charger with compatible batteries only.
Ni-MH batteries gradually lose their charge
when not in use.
■ Disposal
CAUTION: Dispose of used batteries in accord
with local regulations.
vii
For Your Safety
Using the Camera
Do not aim the camera at extremely bright
light sources, such as the sun in a cloudless
sky. Failure to observe this precaution could
damage the camera image sensor.
Take Test Shots
Before taking photographs on important
occasions (such as at weddings or before
taking the camera on a trip), take a test
shot and view the result in the LCD monitor
to ensure that the camera is functioning
normally. FUJIFILM Corporation can not
accept liability for damages or lost profits
incurred as a result of product malfunction.
Notes on Copyright
Unless intended solely for personal use,
images recorded using your digital camera
system cannot be used in ways that infringe
copyright laws without the consent of the
owner. Note that some restrictions apply to
the photographing of stage performances,
entertainments, and exhibits, even when
intended purely for personal use. Users
are also asked to note that the transfer of
memory cards containing images or data
protected under copyright laws is only
permissible within the restrictions imposed
by those copyright laws.
Handling
To ensure that images are recorded correctly,
do not subject the camera to impact or
physical shocks while images are being
recorded.
viii
Liquid Crystal
In the event that the LCD monitor is
damaged, care should be taken to avoid
contact with liquid crystal. Take the urgent
action indicated should any of the following
situations arise:
• If liquid crystal comes in contact with your skin,
clean the area with a cloth and then wash
thoroughly with soap and running water.
• If liquid crystal enters your eyes, flush the
affected eye with clean water for at least 15
minutes and then seek medical assistance.
• If liquid crystal is swallowed, rinse your
mouth thoroughly with water. Drink large
quantities of water and induce vomiting,
then seek medical assistance.
Electrical Interference
This camera may interfere with hospital or
aviation equipment. Consult with hospital
or airline staff before using the camera in a
hospital or on an aircraft.
Color Television Systems
NTSC (National Television System Committee)
is a color television telecasting specification
adopted mainly in the U.S.A., Canada, and
Japan. PAL (Phases Alternation by Line) is
a color television system adopted mainly in
European countries and China.
Exif Print (Exif Version 2.3)
Exif Print is a newly revised digital camera
file format in which information stored
Although the display is manufactured using with photographs is used for optimal color
extremely high-precision technology, it may reproduction during printing.
contain pixels that are always lit or that do not
IMPORTANT NOTICE:
light. This is not a malfunction, and images
Read Before Using the Software
recorded with the product are unaffected.
Direct or indirect export, in whole or in part,
Trademark Information
of licensed software without the permission
xD-Picture Card and E are trademarks of of the applicable governing bodies is
FUJIFILM Corporation. The typefaces included prohibited.
herein are solely developed by DynaComware
Taiwan Inc. Macintosh, QuickTime, and Mac
OS are trademarks of Apple Inc. in the U.S.A.
and other countries. Windows 8, Windows 7,
Windows Vista, and the Windows logo
are trademarks of the Microsoft group of
companies. Adobe and Adobe Reader are
either trademarks or registered trademarks
of Adobe Systems Incorporated in the U.S.A.
and/or other countries. The SDHC and SDXC
logos are trademarks of SD-3C, LLC. The HDMI
logo is a trademark. YouTube is a trademark of
Google Inc. All other trade names mentioned
in this manual are the trademarks or registered
trademarks of their respective owners.
For Your Safety
IMPORTANT: Read the following notices before using the camera’s
Wireless Network Devices: Cautions
built-in wireless transmitter.
• This device operates on the same frequency as commercial, educational,
Q This product, which contains encryption function developed
and medical devices and wireless transmitters. It also operates on the
in the United States, is controlled by the United States Export
same frequency as licensed transmitters and special unlicensed lowAdministration Regulations and may not be exported or revoltage transmitters used in RFID tracking systems for assembly lines
exported to any country to which the United States embargoes
and in other similar applications.
goods.
• To prevent interference with the above devices, observe the following
precautions. Confirm that the RFID transmitter is not in operation
• Use only as part of a wireless network. FUJIFILM does not accept
before using this device. Should you observe that the device
liability for damages resulting from unauthorized use. Do not use
causes interference in licensed transmitters used for RFID tracking,
in applications requiring a high degree of reliability, for example
immediately choose a new operating frequency for this device to
in medical devices or other systems that may directly or indirectly
prevent additional interference. If you notice that this device causes
impact human life. When using the device in computer and other
interference in low-voltage RFID tracing systems, contact a FUJIFILM
systems that demand a greater degree of reliability than wireless
representative.
networks, be sure to take all necessary precautions to ensure safety
and prevent malfunction.
• Use only in the country in which the device was purchased. This device
conforms to regulations governing wireless network devices in the
country in which it was purchased. Observe all location regulations
when using the device. FUJIFILM does not accept liability for
problems arising from use in other jurisdictions.
• Wireless data (images) may be intercepted by third parties. The security
of data transmitted over wireless networks is not guaranteed.
• Do not use the device in locations subject to magnetic fields, static
electricity, or radio interference. Do not use the transmitter in
the vicinity of microwave ovens or in other locations subject to
magnetic fields, static electricity, or radio interference that may
prevent reception of wireless signals. Mutual interference may
occur when the transmitter is used in the vicinity of other wireless
devices operating in the 2.4 GHz band.
• The wireless transmitter operates in the 2.4 GHz band using DSSS and
OFDM modulation.
2.4DS/OF4
This sticker indicates that this device
operates in the 2.4 GHz band using DSSS
and OFDM modulation and may cause
interference at distances of up to 40 m.
ix
About This Manual
Before using the camera, read this manual and the warnings in “For Your Safety”
(P ii). For information on specific topics, consult the sources below.
Table of Contents ...........................P
........................... P xvi
The “Table of Contents” gives an
overview of the entire manual. The
principal camera operations are
listed here.
Troubleshooting .......................... P 102
Having a specific problem with the
camera? Find the answer here.
Warning Messages and Displays ... P 109
Find out what’s behind that flashing
icon or error message in the display.
Memory Cards
Pictures can be stored in the camera’s internal memory or on optional SD, SDHC, and
SDXC memory cards (P 12), referred to in this manual as “memory cards.”
x
Frequently-Used Buttons
■ Deleting Pictures
y To delete a picture, display it full frame
and press the selector up (b).
■ Taking Pictures During Playback
y To return instantly to shooting mode,
press the shutter button halfway.
View
Shoot
■ Turning the Camera on in
Playback Mode
y When the camera is
off, playback can be
started by pressing the
a button for about a
second.
■ Silent Mode
y Press and hold the DISP/
BACK button to disable
camera lights and
sounds.
xi
Product Features and Precautions for Use
■ Water, Dust, and Shock Resistance
Q The camera complies with JIS Class 8 water resistance and JIS Class 6 (IP68) dust resistance
standards, and has passed FUJIFILM drop tests (drop height: 2.0 m/6.5 ft.; impact surface:
plywood, thickness 5 cm/2.0 in.) compliant with MIL-STD 810F Method 516.5: Shock. These
results were obtained through in-house testing and are not a blanket guarantee of water
resistance or invulnerability to damage or destruction. The accessories supplied with the
camera are not water resistant.
■ Before Use
1 Inspect the water-resistant seal and adjacent surfaces and remove
any dust, sand, or other foreign matter using a soft, dry cloth.
Q Have the water-resistant seal replaced if it is deformed or
otherwise damaged (note that a fee is charged for this service;
contact your retailer or a FUJIFILM-authorized repair technician for
more information). Failure to replace the seal could result in leaks
and damage to the camera.
2 Holding the battery-chamber cover closed against the
camera body (q), rotate the latch until it clicks into place
(w), indicating that the cover is secure.
3 Check that the cover is secure by rotating the latch in the opposite direction and confirming
that the cover does not open.
xii
Product Features and Precautions for Use
Q The front surface of the camera lens is protected by a sheet of glass. Foreign matter on the
glass will appear in photographs; keep the glass clean at all times.
Q Be sure that the battery-chamber is fully latched. The presence of water, mud, or sand in the
camera could cause malfunction.
Q Do not open or close the battery-chamber cover with wet hands or in locations that are dusty,
sandy, or near water, for example while on or by a body of water.
Q Be sure the camera is completely dry before inserting or removing batteries or memory cards
or connecting the USB or HDMI cable.
Q The camera does not float. Be sure to attach the strap and keep it around your wrist when
using the camera.
■ During Use
Q Restrict underwater use to depths of 15 m (49 ft.) or less and periods shorter than 120 minutes.
Clean and dry the camera within one hour of using it underwater.
Q The interior of the camera is not waterproof. Do not open or close the battery-chamber cover
while under water. After cleaning the camera, be sure it is completely dry before opening or
closing the battery-chamber cover.
Q Do not use in hot springs or heated pools.
Q The camera may lose water resistance if subjected to excessive force or vibration. Do not dive
into water with the camera or otherwise subject it to excessive force. In the event the camera
is subjected to strong physical shocks, contact your retailer or a FUJIFILM-authorized repair
technician.
Q If the camera is left on the sand, its temperature may exceed operating limits and sand may
get into the speaker or microphone.
Q Sunscreen, suntan lotion, or other oily substances may discolor the camera body and should
be removed with a damp cloth.
xiii
Product Features and Precautions for Use
■ After Use
Perform the following steps after using the camera underwater or in locations where foreign
matter might adhere to the camera body.
1 Securely close the battery-chamber cover and rinse the camera
under the tap or leave it in a basin of fresh water for about ten
minutes.
2 Remove water from the camera with a soft, dry cloth and leave it to dry in a well-ventilated
location in the shade.
3 After confirming that the camera has dried and is free of water droplets, open the batterychamber cover and use a soft, dry cloth to remove any water, dust, or other foreign matter
from the battery chamber.
Q Remove any foreign matter from the water-resistant seal and adjacent surfaces. Foreign
matter could damage the seal, lowering water resistance.
Q Liquid soaps, detergents, alcohol, and other cleansers may affect water resistance and should
never be used.
Q After use, remove water droplets and foreign matter with a dry cloth, firmly latch the batterychamber cover, and soak the camera in fresh water for about ten minutes. Dry the camera
thoroughly after removing it from the water.
xiv
Product Features and Precautions for Use
■ Storage and Maintenance
Q Do not store at temperatures below 0 °C (32 °F) or above 40 °C (104 °F).
Q To ensure continued water resistance, it is recommended that you have the water-resistant
seal replaced about once a year (a fee is charged for this service). Contact your retailer or a
FUJIFILM-authorized repair technician for more information.
■ Condensation Inside the Lens
In some environments, condensation (fog) may form inside of lens.
This does not indicate a malfunction. Condensation can be removed
by leaving the battery-chamber cover open in a location with a steady
temperature that is free of heat, humidity, sand, and dust.
Condensation
Condensation is particularly likely to occur if the camera is placed in cold water after being
exposed to high temperatures or taken from a cold to a warm environment or if the battery
chamber is opened in a humid location.
■ Cold Climates
Q Battery performance drops at low temperatures, reducing the number of pictures that can be
taken. Insulate the camera to keep it warm or place it in your clothing.
Q Use an NP-50 battery.
Q Display response may slow at low temperatures. This is not a malfunction.
xv
Table of Contents
For Your Safety ..................................................................ii
IMPORTANT SAFETY INSTRUCTIONS ..................................ii
Safety Notes ....................................................................iv
About This Manual ............................................................x
Frequently-Used Buttons ................................................xi
Product Features and Precautions for Use.....................xii
Before You Begin
Symbols and Conventions.................................................1
Supplied Accessories .........................................................1
Parts of the Camera ..........................................................2
Camera Displays ...............................................................4
Shooting ........................................................................4
Playback.........................................................................5
First Steps
Inserting the Battery and a Memory Card.......................7
Compatible Memory Cards .............................................12
Charging the Battery ......................................................14
Turning the Camera on and Off ......................................17
Shooting Mode ..............................................................17
Playback Mode ...............................................................17
Basic Setup ......................................................................19
xvi
Basic Photography and Playback
Taking Pictures in Q (Scene Recognition) Mode ......20
Viewing Pictures .............................................................24
More on Photography
Shooting Mode ................................................................25
Choosing a Shooting Mode ............................................25
Shooting Mode Options .................................................26
j PRO LOW-LIGHT ....................................................28
k HDR .....................................................................29
Y ADVANCED FILTER ..................................................30
r MOTION PANORAMA 360 .......................................31
i INDIVID. SHUTTER 3D ..............................................33
b Intelligent Face Detection .......................................35
Focus Lock ........................................................................36
d Exposure Compensation ..........................................38
F Macro Mode (Close-ups) ...........................................39
N Using the Flash (Intelligent Flash) ............................40
h Using the Self-Timer .................................................42
The Burst Mode Button...................................................43
Table of Contents
More on Playback
Connections
Playback Options.............................................................44
I Favorites: Rating Pictures .........................................44
Playback Zoom ...............................................................45
Multi-Frame Playback ....................................................46
A Deleting Pictures......................................................47
b Image Search ............................................................48
k PhotoBook Assist......................................................49
Creating a PhotoBook.....................................................49
Viewing Photobooks ......................................................50
Editing and Deleting Photobooks ...................................50
Viewing Panoramas ........................................................51
Viewing Pictures on High-Definition TVs.......................62
Printing Pictures via USB ................................................63
Printing the DPOF Print Order.........................................65
Viewing Pictures on a Computer ....................................67
Windows: Installing MyFinePix Studio ...........................67
Connecting the Camera ..................................................70
Importing pictures or movies to Mac (Macintosh) ..........72
Wireless Networks
Uploading Pictures..........................................................52
Location Data ..................................................................54
Downloading Location Data ...........................................54
Recording Location Data with Pictures ...........................55
Viewing Location Data ...................................................56
Copying Location Data to Other Images ...........................57
Saving Pictures to a Computer .......................................58
Movies
Recording Movies ............................................................59
Viewing Movies ...............................................................61
Menus
Using the Menus: Shooting Mode ..................................73
Using the Shooting Menu...............................................73
Shooting Menu Options .................................................73
A SHOOTING MODE....................................................73
N ISO........................................................................73
O IMAGE SIZE ............................................................74
T IMAGE QUALITY .....................................................75
P FINEPIX COLOR .......................................................75
D WHITE BALANCE ....................................................76
R CONTINUOUS .........................................................77
b FACE DETECTION.....................................................77
F AF MODE ...............................................................78
F MOVIE AF MODE ....................................................78
W MOVIE MODE .........................................................79
q LED ILLUMINATOR...................................................79
xvii
Table of Contents
Using the Menus: Playback Mode ..................................80
Using the Playback Menu ...............................................80
Playback Menu Options..................................................80
r WIRELESS TRANSFER ..............................................80
s PC AUTO SAVE........................................................80
U LOCATION INFO COPY ..............................................80
k PHOTOBOOK ASSIST ................................................80
b IMAGE SEARCH ......................................................80
A ERASE ...................................................................80
n MOVIE EDIT............................................................81
j MARK FOR UPLOAD TO ............................................82
I SLIDE SHOW ..........................................................83
B RED EYE REMOVAL .................................................83
D PROTECT ................................................................84
G CROP.....................................................................84
O RESIZE ...................................................................85
C IMAGE ROTATE .......................................................85
E COPY .....................................................................86
K PRINT ORDER (DPOF) ..............................................86
J DISP ASPECT ..........................................................87
xviii
The Setup Menu ..............................................................88
Using the Setup Menu....................................................88
Setup Menu Options ......................................................89
F DATE/TIME.............................................................89
N TIME DIFFERENCE ...................................................89
L a ......................................................89
r WIRELESS SETTINGS ...............................................90
s PC AUTO SAVE SETTING ...........................................90
U GEOTAGGING SET-UP ..............................................90
o SILENT MODE .........................................................90
R RESET ....................................................................91
K FORMAT ................................................................91
A IMAGE DISP. ...........................................................91
B FRAME NO. ............................................................92
G OPERATION VOL......................................................93
H SHUTTER VOLUME ..................................................93
e SOUND ..................................................................93
I PLAYBACK VOLUME ................................................93
J LCD BRIGHTNESS ....................................................93
E LCD MODE .............................................................94
M AUTO POWER OFF...................................................94
1 QUICK START MODE................................................94
L DUAL IS MODE .......................................................94
B RED EYE REMOVAL .................................................95
R INTELLIGENT DIGITAL ZOOM ....................................95
p MOVIE ZOOM TYPE .................................................96
C AF ILLUMINATOR ....................................................96
m AUTOROTATE PB ....................................................96
O BACKGROUND COLOR ..............................................96
c GUIDANCE DISPLAY ................................................96
U DATE STAMP ..........................................................97
Table of Contents
Technical Notes
Troubleshooting
Optional Accessories .......................................................98
Accessories from FUJIFILM..............................................99
Caring for the Camera ...................................................100
Storage and Use ...........................................................100
Condensation ..............................................................100
Cleaning .......................................................................101
Traveling ......................................................................101
Problems and Solutions ................................................102
Warning Messages and Displays ..................................109
Appendix
Memory Card Capacity ..................................................113
Specifications ................................................................114
xix
Memo
xx
Before You Begin
Symbols and Conventions
The following symbols are used in this manual:
Q : This information should be read before use to ensure correct operation.
R : Additional information that may be helpful when using the camera.
P: Other pages in this manual on which related information may be found.
Menus and other text in the LCD monitor are shown in bold. In the illustrations
in this manual, displays may be simplified for explanatory purposes.
Supplied Accessories
The following items are included with the camera:
NP-50 rechargeable
battery
• Strap
• User Guide/
Basic Manual
AC power adapter
Plug adapter *
USB cable
CD-ROM (contains
this manual)
Attaching the Strap
Attach the strap as shown.
* Shape of adapter varies with region of sale.
1
Parts of the Camera
For more information, refer to the page listed to the right of each item.
Selector button
Move cursor up
d (exposure compensation) button (P 38)
b (delete) button (P xi)
MENU/OK button
Move cursor left
F (macro) button (P 39)
Move cursor right
N (flash) button (P 40)
Move cursor down
h (self-timer) button (P 42)
* The illustrations in this manual have been simplified for explanatory purposes.
2
Before You Begin
Parts of the Camera
1
2
3
4
5
Microphone.................................................................. 59
Shutter button ............................................................. 22
ON/OFF button............................................................. 17
Flash ............................................................................ 40
Self-timer lamp............................................................ 42
AF-assist illuminator .................................................... 96
LED illuminator ............................................................ 79
6 Lens/protective glass
7 Speaker ........................................................................ 61
8 LCD monitor ................................................................... 4
9 t (movie recording) button ....................................... 59
10 W (zoom out) button ............................................. 21, 45
11 T (zoom in) button ................................................. 21, 45
12 Burst mode button ....................................................... 43
W (wireless transfer) button................................ 52, 58
* Press and hold the DISP/BACK button until o is displayed.
Before You Begin
13
14
15
16
17
18
19
20
21
22
23
24
Latch ........................................................................ 7, 10
Safety lock ............................................................... 7, 10
Strap eyelet .................................................................... 1
DISP (display)/BACK button.................................... 6, 19
o (silent mode) button* ............................................. xi
a (playback) button .................................................. 24
Tripod mount
Water-resistant seal ................................................xii, 10
USB connector........................................................ 63, 70
Memory card slot ........................................................... 9
Micro HDMI connector.................................................. 62
Battery chamber ............................................................ 7
Battery latch ............................................................ 8, 11
3
Parts of the Camera
Camera Displays
The following types of indicator may be displayed during shooting and
playback. Indicators vary with camera settings.
■ Shooting
P
9
800
N
12 / 31 / 2050 10 : 00 AM
-1 2 3
250
F4.5
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Number of available frames ....................................... 113
Sensitivity .................................................................... 73
Image size and quality ........................................... 74, 75
Temperature warning................................................. 110
FINEPIX color ................................................................ 75
White balance .............................................................. 76
Battery level................................................................... 5
Dual IS mode................................................................ 94
Location data download status .................................... 54
Exposure compensation ............................................... 38
Date and time .............................................................. 19
Blur warning ........................................................ 41, 109
Focus warning ...................................................... 22, 109
Date stamp................................................................... 97
Self-timer indicator ...................................................... 42
Macro (close-up) mode ................................................ 39
Flash mode .................................................................. 40
1 Shooting mode ............................................................ 25
2 Intelligent Face Detection indicator.............................. 35
3 Continuous shooting mode .......................................... 77
4 Silent mode indicator ............................................... 3, 90
5 Focus frame.................................................................. 36
6 Internal memory indicator *
7 Movie mode ................................................................. 79
* a: indicates that no memory card is inserted and that pictures will be stored in the camera’s internal memory (P 9); flashes yellow
while images are recorded. If a memory card is inserted, a yellow b icon will flash in the display while images are recorded.
4
Before You Begin
Parts of the Camera
■ Playback
100-0001
400
4:3N
4:3
N
YouTube
12 / 31 / 2050 10 : 00 AM
-1 2 3
1 / 250
F4.5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Playback mode indicator ........................................ 24, 44
Intelligent Face Detection indicator........................ 35, 83
Red-eye removal indicator ........................................... 83
Pro low-light mode, HDR ....................................... 28, 29
3D image...................................................................... 33
Advanced filter ............................................................. 30
Silent mode indicator ............................................... 3, 90
Gift image .................................................................... 44
Frame number ............................................................. 92
Location data ............................................................... 56
Mark for upload to ....................................................... 82
Photobook assist .......................................................... 49
Favorites....................................................................... 44
DPOF print indicator ..................................................... 65
Protected image........................................................... 84
Battery Level
Battery level is shown as follows:
Indicator
D (white)
C (white)
B (red)
A (blinks red)
Description
Battery partially discharged.
Battery more than half discharged.
Low battery. Charge as soon as possible.
Battery exhausted. Turn camera off and charge battery.
Before You Begin
5
Parts of the Camera
Hiding and Viewing Indicators
Press DISP/BACK to cycle through shooting and playback indicators as follows:
• Shooting: Indicators displayed/indicators hidden/best framing/HD framing
• Playback: Indicators displayed/indicators hidden/I favorites
6
Before You Begin
First Steps
Inserting the Battery and a Memory Card
Insert the battery and memory card as described below.
Q Before proceeding, confirm that the water-resistant seal is free of foreign matter as
described on page xii.
1 Open the battery-chamber cover.
Keeping the safety lock pressed (q),
rotate the latch (w) and open the batterychamber cover (e).
R Be sure the camera is off before opening the
battery-chamber cover.
Q Do not open the battery-chamber cover when
the camera is on. Failure to observe this precaution could result in damage to
image files or memory cards.
Q Do not use excessive force when handling the battery-chamber cover.
Q Remove water droplets and other foreign matter with a dry cloth before
opening the battery-chamber cover.
7
Inserting the Battery and a Memory Card
2 Insert the battery.
Align the orange stripe on the battery
with the orange battery latch and slide the
battery into the camera, keeping the battery
latch pressed to one side. Confirm that the
battery is securely latched.
Orange stripe
Battery latch
Q Insert the battery in the correct orientation. Do
NOT use force or attempt to insert the battery
upside down or backwards. The battery will
slide in easily in the correct orientation.
8
First Steps
Inserting the Battery and a Memory Card
3 Insert the memory card.
Holding the memory card in the orientation
shown at right, slide it in until it clicks into
place at the back of the slot.
Q Be sure card is in the correct orientation;
do not insert at an angle or use force. If the
memory card is not correctly inserted or no
memory card is inserted, a will appear in
the LCD monitor and internal memory will be
used for recording and playback.
Q SD/SDHC/SDXC memory cards can be locked,
making it impossible to format the card or to
record or delete images. Before inserting an
SD/SDHC/SDXC memory card, slide the writeprotect switch to the unlocked position.
First Steps
Click
Write-protect switch
9
Inserting the Battery and a Memory Card
4 Close and latch the battery-chamber cover.
Holding the battery-chamber cover closed
against the camera body (q), rotate the
latch until it clicks into place (w), indicating
that the cover is secure.
Q Before closing the cover, confirm that there is
no dust, sand, or other foreign matter on the
water-resistant seal or adjacent surfaces.
Q When closing the battery-chamber cover, do not subject it to excessive
horizontal forces. Failure to observe this precaution could cause the waterresistant seal to become misaligned, allowing water into the camera.
Q Check that the cover is secure by rotating the latch in the opposite direction
and confirming that the cover does not open.
Confirming That the Cover Is Latched
Make sure that the strap is not caught in the cover and that the
latch is closed.
■ Correct
■ Incorrect
The latch is closed.
10
The latch is open.
First Steps
Inserting the Battery and a Memory Card
Removing the Battery and Memory Card
Before removing the battery or memory card, turn the camera off and open the
battery-chamber cover.
To remove the battery, press the battery latch to the side, and
slide the battery out of the camera as shown.
Battery latch
To remove the memory card, press it in and release it slowly.
The card can then be removed by hand. When a memory card
is removed, the card could come out of the slot too quickly.
Use your finger to hold it and gently release the card.
First Steps
11
Inserting the Battery and a Memory Card
■ Compatible Memory Cards
FUJIFILM and SanDisk SD, SDHC, and SDXC memory cards have been approved
for use in the camera. A complete list of approved memory cards is available
at http://www.fujifilm.com/support/digital_cameras/compatibility/. Operation
is not guaranteed with other cards. The camera can not be used with xDPicture Cards or MultiMediaCard (MMC) devices.
Q Memory Cards
• Do not turn the camera off or remove the memory card while the memory card is
being formatted or data are being recorded to or deleted from the card. Failure to
observe this precaution could damage the card.
• Format SD/SDHC/SDXC memory cards before first use, and be sure to reformat all
memory cards after using them in a computer or other device. For more information
on formatting memory cards, see “K FORMAT” (P 91).
• Memory cards are small and can be swallowed; keep out of reach of children. If a
child swallows a memory card, seek medical assistance immediately.
• miniSD or microSD adapters that are larger or smaller than the standard dimensions
of an SD/SDHC/SDXC card may not eject normally; if the card does not eject, take
the camera to an authorized service representative. Do not forcibly remove the card.
• Do not affix labels to memory cards. Peeling labels can cause camera malfunction.
• Movie recording may be interrupted with some types of SD/SDHC/SDXC memory
card. Use a H card or better when shooting HD or high-speed movies.
12
First Steps
Inserting the Battery and a Memory Card
• The data in internal memory may be erased or corrupted when the camera is repaired.
Please note that the repairer will be able to view pictures in internal memory.
• Formatting a memory card or internal memory in the camera creates a folder in
which pictures are stored. Do not rename or delete this folder or use a computer or
other device to edit, delete, or rename image files. Always use the camera to delete
pictures from memory cards and internal memory; before editing or renaming files,
copy them to a computer and edit or rename the copies, not the originals.
Q Batteries
• Remove dirt from the battery terminals with a clean, dry cloth. Failure to observe this
precaution could prevent the battery from charging.
• Do not affix stickers or other objects to the battery. Failure to observe this precaution
could make it impossible to remove the battery from the camera.
• Do not short the battery terminals. The battery could overheat.
• Read the cautions in “The Battery and Power Supply” (P vi).
• Use only battery chargers designated for use with the battery. Failure to observe this
precaution could result in product malfunction.
• Do not remove the labels from the battery or attempt to split or peel the outer casing.
• The battery gradually loses its charge when not in use. Charge the battery one or
two days before use.
First Steps
13
Charging the Battery
The battery is not charged at shipment. Charge the battery before use. The
camera charges the battery internally.
1 Attach the plug adapter to the AC power adapter.
Attach the plug adapter as shown, making
sure that it is fully inserted and clicks into
place on the AC power adapter terminals.
Q The plug adapter is exclusively for use with the
supplied AC power adapter. Do not use it with
other devices.
AC power adapter
Plug adapter
2 Charge the battery.
Turn the camera off and connect the camera
to the supplied AC power adapter using the
supplied USB cable. Then plug the AC power
adapter into an indoor power outlet.
Q Be sure the connectors are in the correct
orientation and then insert them fully.
14
First Steps
Charging the Battery
The Self-timer Lamp
The self-timer lamp shows battery charge status as follows:
Self-timer lamp
On
Blinks
Off
Battery status
Battery charging.
Battery fault.
Charging complete.
Can not charge.
Action
—
See page 103..
—
Unplug the AC power adapter from the power outlet
and reinsert the battery in the correct orientation
(P 103).
Q The battery will not charge while the camera is on.
First Steps
15
Charging the Battery
Charging via a computer
The battery can be charged by connecting the camera to a computer.
Turn the camera off and connect the supplied
USB cable as shown, making sure the
connectors are fully inserted. Connect the
camera directly to the computer; do not use a
USB hub or keyboard.
Q If the camera is turned on, charging is not available.
Q If the computer goes into sleep mode while charging, charging will stop. To
continue charging, disable sleep mode on the computer, and disconnect and
connect the USB cable.
Q Charging may be impossible depending on computer specifications, settings or
conditions.
16
First Steps
Turning the Camera on and Off
Shooting Mode
Press the ON/OFF button to turn the
camera on.
Press ON/OFF again to turn the camera
off.
R Switching to Playback Mode
Press the a button to start playback.
Press the shutter button halfway to return
to shooting mode.
Q You may be prompted to confirm
that the battery-chamber cover is
locked, but this does not indicate a
malfunction.
First Steps
Playback Mode
To turn the camera on and begin
playback, press the a button for
about a second.
Press the a button again or press
the ON/OFF button to turn the camera
off.
R Switching to Shooting Mode
To exit to shooting mode, press the
shutter button halfway. Press the a
button to return to playback.
17
Turning the Camera on and Off
Q Fingerprints and other marks on the protective glass covering the lens can affect
pictures. Keep the glass clean.
Q The ON/OFF button does not completely end the supply of power to the camera.
R Auto Power Off
The camera will turn off automatically if no operations are performed for the length of
time selected for M AUTO POWER OFF (P 94). To turn the camera on, use the ON/OFF
button or press the a button for about a second.
18
First Steps
Basic Setup
A language-selection dialog is displayed the first time the camera is turned
on. Set up the camera as described below (you can reset the clock or change
languages at any time using the F DATE/TIME or L a options in
the setup menu; for information on displaying the setup menu, see page 89).
1 Highlight a language and press MENU/OK.
R Press DISP/BACK to skip the current step. Any steps you skip
will be displayed the next time the camera is turned on.
START MENU
ENGLISH
FRANCAIS
DEUTSCH
ESPAÑOL
PORTUGUÊS
SET
2 The date and time will be displayed. Press the selector
left or right to highlight the year, month, day, hour, or
minute and press up or down to change. To change the
order in which the year, month, and day are displayed,
highlight the date format and press the selector up or
down. Press MENU/OK when settings are complete.
NO
DATE/TIME NOT SET
2015
2014
YY. MM. DD
2013
2012
2011
SET
1. 1 12 : 00
AM
NO
R The Camera Clock
If the battery is removed for an extended period, the camera clock will be reset and the
language-selection dialog will be displayed when the camera is turned on.
First Steps
19
Basic Photography and Playback
Taking Pictures in Q (Scene Recognition) Mode
This section describes how to take pictures in Q (scene
scene recognition)
recognition mode.
The camera automatically analyzes the composition and adjusts settings
appropriately.
1 Turn the camera on.
Press the ON/OFF button to turn the camera on.
Q shooting indicators will be displayed.
The o Icon
This icon indicates that the camera continuously searches for faces to select the
appropriate scene, increasing the drain on the battery.
The Scene Icon
The camera selects the scene according to shooting conditions and the type of
subject (the scenes in brackets are selected if the camera detects that the subject
is moving): d PORTRAIT (a), c LANDSCAPE (cc), d NIGHT (cd), e MACRO (ce),
dd NIGHT PORTRAIT (ad), g BACKLIT PORTRAIT (b), a AUTO (c).
20
Taking Pictures in Q (Scene Recognition) Mode
2 Frame the picture.
Use the zoom buttons to frame the picture in the display.
Zoom out
Zoom in
Zoom indicator
Holding the Camera
Hold the camera steady with both hands and brace your
elbows against your sides. Shaking or unsteady hands can
blur your shots.
To prevent pictures that are out of focus or too dark
(underexposed), keep your fingers and other objects away
from the flash and from the protective glass covering the
lens.
Basic Photography and Playback
21
Taking Pictures in Q (Scene Recognition) Mode
3 Focus.
Press the shutter button halfway to focus.
R The lens may make a noise when the camera focuses; this is
normal. If the subject is poorly lit, the AF-assist illuminator
may light; see“C AF ILLUMINATOR”(P 96) for information
on disabling the illuminator.
Double
beep
If the camera is able to focus, it will beep twice.
If the camera is unable to focus, the focus frame will turn red, s will be
displayed. Change the composition or use focus lock (P 36).
22
Basic Photography and Playback
Taking Pictures in Q (Scene Recognition) Mode
4 Shoot.
Smoothly press the shutter button the rest of the way
down to take the picture.
Click
R If the subject is poorly lit, the flash may fire when the
picture is taken. For information on using the flash when
lighting is poor, see “N Using the Flash (Intelligent Flash)”
(P 40).
The Shutter Button
The shutter button has two positions. Pressing the shutter button halfway sets
focus and exposure; to shoot, press the shutter button the rest of the way down.
Basic Photography and Playback
23
Viewing Pictures
Pictures can be viewed in the LCD monitor. When taking important
photographs, take a test shot and check the results.
1 Press the a button.
The most recent picture will be displayed.
2 View additional pictures.
Press the selector right to view pictures in the
order recorded, left to view pictures in reverse
order.
Press the shutter button halfway to exit to
shooting mode.
24
Basic Photography and Playback
More on Photography
Shooting Mode
Choose a shooting mode according to the scene or type of subject.
Choosing a Shooting Mode
1 Press MENU/OK to display the shooting menu.
2 Highlight
A SHOOTING MODE and press the
SHOOTING MENU
SHOOTING MODE
selector right to display shooting mode options.
SET
EXIT
3 Highlight the desired mode and press MENU/OK.
QSCENE RECOGNITION
Selects optimum
camera settings
for certain modes.
SET
CANCEL
4 Press DISP/BACK to exit to shooting mode.
25
Shooting Mode
Shooting Mode Options
Mode
Description
The camera automatically analyzes the composition and selects a scene
Q SCENE RECOGNITION
according to shooting conditions and the type of subject.
Choose for crisp, clear snapshots. This mode is recommended in most
B AUTO
situations.
P PROGRAM AE
The camera sets exposure automatically.
Choose when photographing stationary subjects under low light or with
j PRO LOW-LIGHT
the camera zoomed in (P 28).
Choose when photographing high-contrast scenes. The camera varies
exposure over a series of shots and blends the results to preserve details
k HDR
in highlights and shadows (P 29).
The camera takes two shots: one without the flash and one with.
C NATURAL & N
Capture natural lighting under low-light conditions.
D NATURAL LIGHT
Choose for portraits.
L PORTRAIT
Choose for daylight shots of buildings and landscapes.
M LANDSCAPE
Y ADVANCED FILTER
Take photos with filter effects (P 30).
r MOTION PANORAMA Pan the camera to record a series of shots that are joined together to form
a panorama (P 31).
360
Choose when photographing moving subjects.
N SPORT
26
More on Photography
Shooting Mode
Mode
O NIGHT
H NIGHT (TRIPOD)
Q SUNSET
R SNOW
Description
Choose this mode for poorly lit twilight or night scenes.
Choose this mode for slow shutter speeds when shooting at night.
Choose this mode to record the vivid colors in sunrises and sunsets.
Choose for crisp, clear shots that capture the brightness of scenes
dominated by shining white snow.
S BEACH
Choose for crisp, clear shots that capture the brightness of sunlit beaches.
F UNDERWATER
s UNDER WATER
(MACRO)
U PARTY
V FLOWER
W TEXT
i INDIVID. SHUTTER 3D
Choose for underwater photography.
More on Photography
Choose for underwater close-ups of small objects.
Capture indoor background lighting under low-light conditions.
Choose for vivid close-ups of flowers.
Take clear pictures of text or drawings in print.
Take two shots from different angles to create a 3D image (P 33).
27
Shooting Mode
■ j PRO LOW-LIGHT
Each time the shutter button is pressed, the camera
makes four exposures and combines them into a
single photograph. Use to reduce noise and blur when
photographing poorly lit subjects or static subjects at high
zoom ratios.
R A single combined photograph may not be created with some scenes or if the
subject or camera moves during shooting. Do not move the camera until shooting
is complete.
PRO LOW-LIGHT
Q Keep the camera steady during shooting.
Q Frame coverage is reduced.
Q The camera may make fewer than four exposures in some situations.
28
More on Photography
Shooting Mode
■ k HDR
Each time the shutter button is pressed, the camera takes a series of shots, each
with different exposure. These are combined into a single image, preserving
detail in highlights and shadows. Choose for high-contrast scenes. Press the
selector left or right to choose the exposure range before shooting.
R A single combined photograph may not be created with some scenes or if the
subject or camera moves during shooting. Do not move the camera until shooting
is complete.
D-RANGE PRIORITY
Q Keep the camera steady during shooting.
Q Frame coverage is reduced.
More on Photography
29
Shooting Mode
■ Y ADVANCED FILTER
Take photos with filter effects.
1 Select Y ADVANCED FILTER for shooting mode (P 25).
2 Select a filter effect and press MENU/OK.
G
H
I
J
X
L
u
v
w
x
y
z
Filter
TOY CAMERA
MINIATURE*1
POP COLOR
HIGH-KEY
SOFT FOCUS
CROSS SCREEN*1
PARTIAL COLOR (RED)
PARTIAL COLOR (ORANGE)
PARTIAL COLOR (YELLOW)
PARTIAL COLOR (GREEN)
PARTIAL COLOR (BLUE)
PARTIAL COLOR (PURPLE)
Description
Choose for a retro toy camera effect.
The tops and bottoms of pictures are blurred for a diorama effect.
Create high-contrast images with saturated colors.
Create bright, low-contrast images.
Create a look that is evenly soft throughout the whole image.
Create a star pattern where lines radiate out from bright objects.
Areas of the image that are the selected color are recorded in that
color. All others areas of the image are recorded in black-and-white.
*1 To check the effect, play the picture after shooting.
R Depending on the subject and camera settings, images may in some cases be
grainy or vary in brightness and hue.
30
More on Photography
Shooting Mode
■ r MOTION PANORAMA 360
Follow an on-screen guide to take photos that will
automatically be joined to form a panorama. The camera
zooms all the way out and remains fixed at the widest
angle until shooting is complete.
1 To select the angle through which you will pan the
camera while shooting, press the selector down. Press the selector left or
right to highlight an angle and press MENU/OK.
2 Press the selector right to view a choice of pan directions. Press the selector
left or right to highlight a pan direction and press MENU/OK.
3 Press the shutter button all the way down to start recording. There is no
need to keep the shutter button pressed during recording.
4 Pan the camera in the direction shown by the arrow.
120
Shooting ends automatically when the progress bar is
full and the panorama is complete.
R Shooting ends if the shutter button is pressed all the way
down during shooting. No panorama will be recorded if
the shutter button is pressed before the camera has been
panned through 120 °.
More on Photography
Progress bar
31
Shooting Mode
Q Panoramas are created from multiple frames. The camera may in some cases record
an greater or lesser angle than selected or be unable to stitch the frames together
perfectly. The last part of the panorama may not be recorded if shooting ends
before the panorama is complete.
Q Shooting may be interrupted if the camera is panned too quickly or too slowly.
Panning the camera in a direction other than that shown cancels shooting.
Q The desired results may not be achieved with moving subjects, subjects close to
the camera, unvarying subjects such as the sky or a field of grass, subjects that are
in constant motion, such as waves and waterfalls, or subjects that undergo marked
changes in brightness. Panoramas may be blurred if the subject is poorly lit.
For Best Results
For best results, move the camera in a small circle at a steady speed, keeping the
camera horizontal and being careful only to pan in the direction shown by the
guides. If the desired results are not achieved, try panning at a different speed.
32
More on Photography
Shooting Mode
■ i INDIVID. SHUTTER 3D
Take two shots from different angles to create a 3D image.
1 Select i INDIVID. SHUTTER 3D for shooting mode (P 25).
2 To choose the order in which the pictures are taken,
TURN
press the selector right to display the current order and
then press the selector left or right to choose from the
options below.
G: Take the left shot first.
H: Take the right shot first.
3 Press the shutter button to take the first shot.
R To exit without recording a picture, press DISP/BACK.
4 The first shot will be shown superimposed on the view through the lens.
Using it as a guide, frame the second shot and press the shutter release
button.
R The 3D effect may not be visible with some
subjects or under some shooting conditions. For
best results, the distance the camera is moved
between shots should be about 1/30th to 1/50th of
the distance to the subject.
R The camera will turn off automatically if no operations performed for the time
selected for M AUTO POWER OFF (P 94). The first shot will not be saved if the
second shot is not taken before the camera turns off.
More on Photography
33
Shooting Mode
Viewing and Printing 3D Images
• The camera displays images in 2D. Press the selector down to toggle between the
first and second shots.
• Devices equipped for 3D display, such as the FINEPIX REAL 3D V3 digital photo frame
or FINEPIX REAL 3D W3 digital camera, will display the images in 3D. Note that the
FINEPIX REAL 3D W3 only displays images of size P or smaller.
• 3D prints can be ordered from http://www.fujifilm.com/3d/print/
• The supplied software displays 3D anaglyph images. 3D photos can also be viewed
using other applications that support the MP format.
• 3D TVs that support the MP format can display images in 3D. See the manual for
your TV for details.
Q Images are not output in 3D when printed directly from the camera.
Q 3D images are displayed in 2D in slide shows and when output on a conventional
TV.
Q 3D images can not be edited.
Note: The MP (Multi-Picture) format is a CIPA standard for files containing multiple still images. Files
in MP format are referred to as “MP files” and have the extension “*.MPO”. The camera uses this
format for 3D images.
34
More on Photography
b Intelligent Face Detection
Intelligent Face Detection sets focus and exposure for human faces anywhere
in the frame, preventing the camera from focusing on the background in
group portraits. Choose for shots that emphasize portrait subjects.
To use Intelligent Face Detection, press MENU/OK
to display the shooting menu and select ON for
b FACE DETECTION (P 77). Faces can be detected
with the camera in vertical or horizontal orientation;
if a face is detected, it will be indicated by a green
border. If there is more than one face in the frame,
the camera will select the face closest to the center;
other faces are indicated by white borders.
Q In some modes, the camera may set exposure for the frame as a whole rather than
the portrait subject.
Q If the subject moves as the shutter button is pressed, their face may not be in the
area indicated by the green border when the picture is taken.
More on Photography
35
Focus Lock
To compose photographs with off-center subjects:
1 Focus: Position the subject in the focus frame (U)
and press the shutter button halfway to lock focus
and exposure. Focus and exposure will remain locked
while the shutter button is pressed halfway (AF/AE
lock).
2 Recompose: Keep the button pressed halfway.
3 Shoot: Press the button all the way down.
36
More on Photography
Focus Lock
Autofocus
Although the camera boasts a high-precision autofocus system, it may be unable to
focus on the subjects listed below. If the camera is unable to focus, focus on another
subject at the same distance and use focus lock to recompose the photograph.
• Very shiny subjects such as mirrors or car bodies.
• Subjects that show little contrast with the background
• Fast-moving subjects.
(for example, subjects in clothing that is the same color
• Subjects photographed through a window or other as the background).
reflective object.
• Subjects positioned in front of or behind a high-contrast
• Dark subjects and subjects that absorb rather than reflect object that is also in the focus frame (for example, a
light, such as hair or fur.
subject photographed against a backdrop of highly
• Insubstantial subjects, such as smoke or flame.
contrasting elements).
More on Photography
37
d Exposure Compensation
To adjust exposure compensation when
photographing very bright, very dark, or highcontrast subjects, press the selector up (d). Press
the selector up or down to choose an exposure
compensation value and then press MENU/OK.
Choose positive (+) values
to increase exposure
Choose negative (–) values
to reduce exposure
R A d icon and exposure indicator are displayed at settings other than ±0. Exposure
compensation is not reset when the camera is turned off; to restore normal
exposure control, choose a value of ±0.
R Turn the flash off when using exposure compensation.
R Exposure compensation is available only when P (PROGRAM AE) is selected for
shooting mode.
38
More on Photography
F Macro Mode (Close-ups)
For close-ups, press the selector left (F) and select
F. When macro mode is in effect, the camera
focuses on subjects near the center of the frame.
Use the zoom buttons to compose pictures (P 21).
To exit macro mode, press the selector left (F) and
select H.
OFF
OFF
R Use of a tripod is recommended to prevent blur caused
by camera shake.
More on Photography
39
N Using the Flash (Intelligent Flash)
When the flash is used, the camera’s Intelligent Flash system instantly analyzes
the scene based on such factors as the brightness of the subject, its position
in the frame, and its distance from the camera. Flash output and sensitivity are
adjusted to ensure that the main subject is correctly exposed while preserving
the effects of ambient background lighting, even in dimly-lit indoor scenes.
Use the flash when lighting is poor, for example when shooting at night or
indoors under low light.
Press the selector right (N) and choose from the
following flash modes:
P
AUTO FLASH
According to
shooting conditions
Option
AUTO/K
(AUTO FLASH)
FLASH)
N/L
(FORCED FLASH)
FLASH)
Description
The flash fires when required. Recommended in most situations.
The flash fires whenever a picture is taken. Use for backlit subjects or for natural
coloration when shooting in bright light.
P
The flash does not fire even when the subject is poorly lit. Use of a tripod is
(SUPPRESSED FLASH
FLASH)) recommended.
O/M
Capture both the main subject and the background under low light (note that
(SLOW SYNCHRO)
SYNCHRO) brightly lit scenes may be overexposed).
40
More on Photography
N Using the Flash (Intelligent Flash)
R If the flash will fire, p will be displayed when the shutter button is pressed halfway
(if the icon blinks yellow, the flash charging; wait for charging to complete before
shooting). At slow shutter speeds, k will appear in the display to warn that pictures
may be blurred; use of a tripod is recommended.
R The flash may fire several times with each shot. Do not move the camera until
shooting is complete.
R The flash may cause vignetting.
Red-Eye Removal
When Intelligent Face Detection (P 35) and red-eye removal (P 83) are
on, red-eye removal is available in auto (K; RED EYE REDUCTION), flash
on (L; FORCED FLASH), and slow sync (M; RED EYE & SLOW) modes.
Red-eye removal minimizes “red-eye” caused when light from the flash is
reflected from the subject’s retinas as shown in the illustration at right.
More on Photography
41
h Using the Self-Timer
To use the self-timer, press the selector down (h)
and choose from the following options:
OFF
OFF
Option
Description
Self-timer off.
The shutter is released ten seconds after the shutter button is pressed. Use for
S (10 SEC)
self-portraits. The self-timer lamp on the front of the camera blinks while the
timer counts down.
The shutter is released two seconds after the shutter button is pressed. Use to
R (2 SEC)
reduce blur caused by the camera moving when the shutter-release button is
pressed. The self-timer lamp will blink as the timer counts down.
The camera will start the timer when it detects the selected number of portrait
g (GROUP TIMER) subjects. Press the selector up to choose the number of subjects.
R To stop the timer before the picture is taken, press DISP/BACK.
T (OFF)
42
More on Photography
The Burst Mode Button
Press the burst mode button to toggle between
single-frame shooting and the burst mode selected
using the Continuous option in the shooting menu
(P 77).
R When a burst mode is selected, the camera displays the icon
for the selected mode. No icon is displayed in single-frame
mode.
More on Photography
P
43
More on Playback
Playback Options
To view the most recent picture in the LCD monitor, press the a button.
100-0001
Press the selector right to view pictures in the order recorded, left to view
pictures in reverse order. Keep the selector pressed to scroll rapidly to the
desired frame.
R Pictures taken using other cameras are indicated by a m (“gift image”) icon during
playback.
I Favorites: Rating Pictures
To rate the picture currently displayed in full-frame playback, press DISP/BACK
and press the selector up and down to select from zero to five stars.
44
Playback Options
Playback Zoom
Press T to zoom in on pictures displayed in single-frame playback; press W to
zoom out. When the picture is zoomed in, the selector can be used to view
areas of the image not currently visible in the display.
Zoom indicator
Navigation window shows
portion of image currently
displayed in LCD monitor
Press DISP/BACK to exit zoom.
R The maximum zoom ratio varies with image size. Playback zoom is not available
with cropped or resized copies saved at a size of a or smaller.
More on Playback
45
Playback Options
Multi-Frame Playback
Pressing W when a picture is shown full-frame in the LCD monitor displays the
current image with previous and following images in the background. Press
W to increase the number of images displayed to two, nine, or one hundred,
T to view fewer images.
100-0001
When two or more images are displayed, use the selector to highlight images
and press MENU/OK to view the highlighted image full frame. In the nine- and
hundred-frame displays, use the selector to view more pictures.
46
More on Playback
A Deleting Pictures
To delete individual pictures, multiple selected
pictures, or all pictures, press the selector up
(b), and choose from the options below. Note
that deleted pictures can not be recovered. Copy
important pictures to a computer or other storage device before proceeding.
ERASE
FRAME
SELECTED FRAMES
ALL FRAMES
SET
BACK
Option
Description
Press the selector left or right to scroll through pictures and press MENU/OK to
FRAME
delete the current picture (a confirmation dialog is not displayed).
Highlight pictures and press MENU/OK to select or deselect (pictures that
are protected or in a print order are shown by u). When the operation is
SELECTED FRAMES
complete, press DISP/BACK to display a confirmation dialog, then highlight OK
and press MENU/OK to delete the selected pictures.
A confirmation dialog will be displayed; highlight OK and press MENU/OK to
delete all unprotected pictures (if a memory card is inserted, only the pictures
on the memory card will be affected; the pictures in internal memory are only
ALL FRAMES
deleted if no memory card is inserted). Pressing DISP/BACK cancels deletion;
note that any pictures deleted before the button was pressed can not be
recovered.
R Protected pictures can not be deleted. Remove protection from any pictures you
wish to delete (P 84).
R Pictures can also be deleted by A ERASE from playback menu.
R If a message appears stating that the selected images are part of a DPOF print order,
press MENU/OK to delete the pictures.
More on Playback
47
b Image Search
Search for pictures.
1 Select b IMAGE SEARCH in the playback menu (P 80), highlight one of
the following search criteria, and press MENU/OK:
• BY DATE: Search by date.
• BY FACE: Find all pictures containing faces.
• BY I FAVORITES: Search by rating.
• BY TYPE OF DATA: Find all still pictures or all movies.
• BY UPLOAD MARK: Find all pictures selected for upload to a specified
destination.
2 Select a search condition. Only pictures that match the search condition
will be displayed. To delete or protect selected pictures or to view the
search results in a slide show, press MENU/OK and choose A ERASE (P 47),
D PROTECT (P 84), or I SLIDE SHOW (P 83).
48
More on Playback
k PhotoBook Assist
Create books from your favorite photos.
Creating a PhotoBook
1 Select NEW BOOK for k PHOTOBOOK ASSIST in the playback menu
(P 80) and choose from the following options:
• SELECT FROM ALL: Choose from all available pictures.
• SELECT BY IMAGE SEARCH: Choose from pictures matching selected search
conditions (P 48).
R Neither photographs a or smaller nor movies can be selected for photobooks.
2 Scroll through the images and press the selector up to select or deselect.
To display the current image on the cover, press the selector down. Press
MENU/OK to exit when the book is complete.
R The first picture selected becomes the cover image. Press the selector down to
select a different image for the cover.
3 Select COMPLETE PHOTOBOOK (to select all photos or all photos
matching the specified search conditions for the book, choose SELECT
ALL). The new book will be added to the list in the photobook assist menu.
Q Books can contain up to 300 pictures.
Q Books that contain no photos are automatically deleted.
More on Playback
49
k PhotoBook Assist
Viewing Photobooks
Highlight a book in the photobook assist menu and press MENU/OK to display
the book, then press the selector left or right to scroll through the pictures.
Editing and Deleting Photobooks
Display the photobook and press MENU/OK. The following options will be
displayed; select the desired option and follow the on-screen instructions.
• EDIT: Edit the book as described in “Creating a PhotoBook” (P 49).
• ERASE: Delete the book.
Photobooks
Photobooks can be copied to a computer using the supplied MyFinePix Studio
software.
50
More on Playback
Viewing Panoramas
If you press the selector down when a panorama is displayed full frame, the
camera will play back the picture from left to right or from bottom to top. To
pause playback, press the selector down; press the selector down again to
resume. To exit to full-frame playback, press the selector up while panorama
playback is in progress. Once displayed in full-frame playback, panoramas
can be zoomed in or out using the zoom control or deleted by pressing the
selector up (b).
PLAY
STOP
More on Playback
PAUSE
51
Wireless Networks
Uploading Pictures
Connect via a wireless network to upload pictures to smartphones or tablets or
to remotely browse the pictures on the camera and select images for download.
Before proceeding, download the free FUJIFILM Camera Application app and
install it on your smartphone or tablet. To download the app or view information
on using FUJIFILM Camera Application, visit http://app.fujifilm-dsc.com/app.
To upload pictures or view pictures remotely:
1 Press MENU/OK during playback to display the
playback menu.
2 Select r WIRELESS TRANSFER.
3 Choose from the following options:
Option
SEND INDIVIDUAL
IMAGE
SEND SELECTED
MULTIPLE IMAGES
VIEW & OBTAIN
IMAGES ON r
52
Description
Upload the current picture to the smartphone.
Upload selected pictures to the smartphone.
Use the smartphone to view the photos and movies
on the camera and select pictures for download.
WIRELESS TRANSFER
SEND INDIVISUAL IMAGE
SEND SELECTED MULTIPLE IMAGES
VIEW & OBTAIN IMAGES ON r
Uploading Pictures
R The r WIRELESS TRANSFER menu can also be displayed by pressing the W
button.
R Pictures can also be uploaded to devices running the FUJIFILM Photo Receiver app.
R Be sure that the battery is charged before beginning upload. Do not remove the
battery, turn the camera off, or remove the memory card until upload is complete.
R If you are unable to upload still pictures, check the smartphone’s settings.
R Personal information may be revealed by the titles, dates, location data, and other
information included with pictures. Verify the destination before beginning upload.
R The time needed for upload varies with file size and the distance to the destination.
At default settings (recommended), ON is selected for r WIRELESS SETTING >
RESIZE IMAGE FOR SMARTPHONE H (P 90) and images are resized to H for
upload.
R The camera may be unable to upload images created or modified on other devices.
R Movies can not be uploaded using the SEND INDIVIDUAL IMAGE and SEND
SELECTED MULTIPLE IMAGES options.
R Upload may not succeed depending on signal quality.
R The camera will end the connection to the smartphone automatically if no
operations are performed for a set period.
Wireless Networks
53
Location Data
The U GEOTAGGING SET-UP > LOCATION INFO SEARCH option in
the setup menu can be used to download location data from smartphones running the free FUJIFILM Camera Application app. The location data can then be added to pictures as they are taken. To download
the app or view information on using FUJIFILM Camera Application, visit
http://app.fujifilm-dsc.com/app.
Downloading Location Data
To download data for your current location from a smartphone:
1 Press MENU/OK to display the menu for the current
mode.
2 Press the selector left to highlight the tab for the
SET-UP
current menu.
3 Press the selector down to highlight X.
SET
SET
EXIT
Tab
4 Press the selector right to place the cursor in the setup menu.
5 Select U GEOTAGGING SET-UP > LOCATION INFO SEARCH. Note that
the accuracy of data will vary from device to device.
54
Wireless Networks
Location Data
Recording Location Data with Pictures
To save location data with new pictures:
1 Download data on your current location from a smartphone (P 54).
2 Select ON for U GEOTAGGING SET-UP > GEOTAGGING.
3 Take pictures. The location data acquired in Step 2 will be added to the
new images.
The camera will display the latitude and longitude of the
most recently acquired location. In addition, a i icon will
be displayed if location data have been updated in the last
two hours; if the time elapsed since the last update is more
than two hours, the i icon will flash. A j icon indicates
that no location data are available.
Wireless Networks
P
N 35° 66’ 55”
E 139° 73’ 04”
55
Location Data
R To disable geotagging, select OFF for U GEOTAGGING SET-UP > GEOTAGGING.
To choose whether the camera displays the current location, use U GEOTAGGING
SET-UP > LOCATION INFO.
Q The camera uses the most recently downloaded data; if you have changed your
location since you last took a picture, download data for the current location before
shooting. Note that the camera automatically stops recording location data three
hours after the last update.
■ Viewing Location Data
During playback, pictures for which location data exist are
indicated by a k icon. Location data are shown for a few
seconds each time the picture is displayed.
k icon
100-0001
N 35° 66’ 55”
56
E 139° 73’ 04”
Wireless Networks
Location Data
■ Copying Location Data to Other Images
Location data can be copied from other pictures to images that lack correct
location information.
1 Select U LOCATION INFO COPY in the playback menu (P 80).
2 Press the selector left or right to display the source image for the location
data and press MENU/OK.
3 Press the selector left or right to display the destination and press MENU/OK
to copy the data to the image.
Q Once copied, the new location data can not be deleted and the original location
data can not be recovered. Note, however, that copying data from a picture with
location data to another picture with location data will delete the original location
data recorded with the destination picture.
Q The camera may be unable to copy location data to or from images created on
other devices.
Wireless Networks
57
Saving Pictures to a Computer
Follow the steps below to save pictures to a computer over a wireless network.
Before proceeding, install the free FUJIFILM PC AutoSave application to the
destination computer and adjust settings as desired. Be sure the camera
battery is fully charged.
R Visit the following website for information on downloading FUJIFILM PC AutoSave
and adjusting settings: http://app.fujifilm-dsc.com/pc/.
1 During playback, press MENU/OK to display the
playback menu.
2 Select s PC AUTO SAVE.
R A s PC AUTO SAVE option is also available in the
r WIRELESS TRANSFER menu, which can be displayed
by pressing the W button.
SELECT DESTINATION PC
MY-PC
PC-01
PC-02
PC-03
PC-04
PC-05
3 The options shown at right will be displayed; select a destination.
R The destination can also be selected using s PC AUTO SAVE SETTING.
4 Follow the on-screen instructions.
R Do not turn the camera off or remove the camera battery or memory card while
transfer is in progress.
R The camera will turn off automatically shortly after upload is completed.
58
Wireless Networks
Movies
Recording Movies
Press t to shoot a movie. During recording, the
following indicators will be displayed and sound will
be recorded via the built-in microphone (be careful
not to cover the microphone during recording).
y REC icon
REC
1
12m34s
F
Number of photos that
can be taken during
recording
Time remaining
To end recording, press the t button again. Recording ends automatically
when the movie reaches maximum length or memory is full.
Automatic Scene Selection
In Q mode, the camera selects the scene according to shooting
conditions and the type of subject: d (portraits), dd (poorly-lit
landscapes), f (poorly-lit portraits), c (landscapes), e (closeups), or a (other subjects).
REC
1
12m34s
F
Scene icon
59
Recording Movies
Taking Photographs During Recording
Press the shutter button to take a photograph during recording.
R The photo is saved separately from the movie and does not appear as part of the movie.
Q Photos can not be taken while a high-speed movie is being recorded.
Q The number of photos that can be taken is limited.
R Zoom can be adjusted while recording is in progress. The type of zoom can be
selected using the p MOVIE ZOOM TYPE option in the setup menu (P 96).
R If the subject is poorly lit, the AF-assist lamp may light to assist the focus operation.
To turn the AF-assist lamp off , select OFF for C AF ILLUMINATOR (P 96).
R Focus, exposure and white balance are adjusted automatically throughout
recording (the focus mode can be selected using the F MOVIE AF MODE option
in the shooting menu; P 78). The color and brightness of the image may vary from
that displayed before recording begins.
R Sounds made by the camera may be recorded.
Q Do not open the battery-chamber cover during shooting or saving a movie on a
memory card. Failure to observe this precaution could prevent the movie from
being played back.
Q Vertical or horizontal streaks may appear in movies containing very bright subjects.
This is normal and does not indicate a malfunction.
Q The temperature of the camera may rise if it is used to record movies for an extended
period or if the ambient temperature is high. This is normal and does not indicate
a malfunction.
Q The mode selected may vary with shooting conditions.
60
Movies
Viewing Movies
During playback, movies are displayed in the LCD monitor
as shown at right. The following operations can be
performed while a movie is displayed:
Option
Start/pause
playback
End playback/
delete
Description
Press the selector down to start playback. Press again to
pause.
Press the selector up to end playback. If playback is not in
progress, pressing the selector up will delete the movie.
Press the selector left or right to adjust playback speed
Adjust speed
during playback.
Press MENU/OK to pause playback and display volume
controls. Press the selector up or down to adjust the
Adjust volume
volume and press MENU/OK to exit. Volume can also be
adjusted from the setup menu.
100-006
PLAY
Playback Speed
Press the selector left or right to adjust playback speed. Speed is Arrow
shown by the number of arrows (M or N).
STOP
5m42s
PAUSE
Q Do not cover the speaker during playback.
Movies
61
Connections
Viewing Pictures on High-Definition TVs
The camera can be connected to High-Definition (HD) devices using an HDMI
cable (available separately from third-party sources).
1 Turn the camera off and connect the HDMI cable as shown below.
Micro HDMI connector
Insert into HDMI
connector
Insert into HDMI
connector
Q When connecting cables, be sure the connectors are fully inserted.
R When an HDMI cable is connected, pictures and sound are played back on the TV.
2 Tune the television to the HDMI input channel. See the documentation
supplied with the television for details.
3 Press the a button for about a second to turn the camera on. The camera
monitor turns off and pictures and movies are played back on the TV. Note
that the camera volume controls have no effect on sounds played on the
TV; use the television volume controls to adjust the volume.
R The USB cable can not be used while an HDMI cable is connected.
R Some televisions may briefly display a black screen when movie playback begins.
62
Printing Pictures via USB
If the printer supports PictBridge, the camera can be connected
directly to the printer as shown below and pictures can be printed
without first being copied to a computer. Note that depending on
the printer, not all the functions described below may be supported.
1 Connect the supplied USB cable as shown and turn the printer on.
2 Turn the camera on.
3 Press the selector left or right to display a picture you wish to print.
4 Press the selector up or down to choose the number of copies (up to 99).
5 Repeat steps 3–4 to select additional pictures. Press MENU/OK to display a
confirmation dialog when settings are complete.
Connections
63
Printing Pictures via USB
6 Press MENU/OK to start printing. Printing can be interrupted by pressing
DISP/BACK, but note that some printers may not respond immediately. If
the printer stops before printing is complete, turn the camera off and then
on again.
7 After confirming that PRINTING has cleared from the camera display, turn
the camera off and disconnect the USB csable.
R If no pictures are selected, the camera will print one copy of the current picture.
R Page size, print quality, and border selections are made using the printer.
Printing the Date of Recording
To print the date of recording on pictures, press DISP/BACK in the PictBridge display
and select PRINT WITH DATE s in the PictBridge menu (to print pictures without
the date of recording, select PRINT WITHOUT DATE).
64
Connections
Printing Pictures via USB
Printing the DPOF Print Order
The K PRINT ORDER (DPOF) option in the playback menu can be used to
create a digital“print order”for PictBridge-compatible printers (P 98) or devices
that support DPOF.
DPOF
DPOF (Digital Print Order Format) is a standard that allows pictures to be
printed from “print orders” stored in internal memory or on a memory card.
The information in the order includes the pictures to be printed and the
number of copies of each picture.
1 Select playback mode and press MENU/OK to display the playback menu.
2 Highlight K PRINT ORDER (DPOF) and press MENU/OK.
3 Highlight one of the following options and press MENU/OK:
• WITH DATE s: Print the date of recording on pictures.
• WITHOUT DATE: Do not print the date of recording on pictures.
R Some printers do not support date printing. See the printer manual for details.
4 Press the selector left or right to display a picture you wish to add to or
remove from the print order.
Connections
65
Printing Pictures via USB
5 Press the selector up or down to choose the number of copies (up to 99).
To remove a picture from the print order, press the selector down until the
number of copies is zero.
6 Repeat Steps 4–5 to complete the print order and press MENU/OK when
settings are complete.
7 A confirmation dialog will be displayed. Press MENU/OK to save the print
order.
R Remove the memory card to create or modify a print order for the pictures in
internal memory.
R Print orders can contain a maximum of 999 pictures.
R If a memory card is inserted containing a print order created by another camera,
a message will be displayed. Create a new print order as described above.
66
Connections
Viewing Pictures on a Computer
The supplied software can be used to copy pictures to a computer, where
they can be stored, viewed, organized, and printed. Before proceeding, install
the software as described below. Do NOT connect the camera to the computer
until installation is complete.
Windows: Installing MyFinePix Studio
1 Confirm that the computer meets the following system requirements:
Windows 8/Windows 7 (SP 1)/
Windows Vista (SP 2) 1
3 GHz Pentium 4 or better
(2.4 GHz Core 2 Duo or better) 2
Windows XP (SP 3) 1
2 GHz Pentium 4 or better
(2.4 GHz Core 2 Duo or better) 2
512 MB or more
RAM
1 GB or more
(1 GB or more) 2
Free disk space
2 GB or more
Supports DirectX 9 or later
Supports DirectX 7 or later
GPU
(recommended
recommended))
(required; performance not guaranteed with other GPUs)
GPUs)
Video
1,024 × 768 pixels or more with 24-bit color or better
• Built-in USB port recommended. Operation is not guaranteed with other
USB ports.
• .NET Framework 3.5 Service Pack 1 required when uploading images or
Other
using Map Viewer.
• Internet connection (broadband recommended) required to install
.NET Framework (if necessary), to use auto update feature, and when
performing such tasks as sharing pictures on-line or via e-mail.
1 Other versions of Windows are not supported. Only pre-installed operating systems are
supported; operation is not guaranteed on home-built computers or computers that have
been upgraded from earlier versions of Windows.
2 Recommended when displaying HD movies.
CPU
Connections
67
Viewing Pictures on a Computer
2 Start the computer. Log in to an account with administrator privileges
before proceeding.
3 Exit any applications that may be running and insert the installer CD in a
CD-ROM drive.
Windows 8/Windows 7/Windows Vista
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control”
dialog will then be displayed; click Yes (Windows 8/Windows 7) or Allow
(Windows Vista).
The installer will start automatically; click Install MyFinePix Studio and
follow the on-screen instructions to install MyFinePix Studio.
If the Installer Does Not Start Automatically (Windows 7/Windows Vista/Windows XP)
If the installer does not start automatically, select Computer or My Computer
from the Start menu, then double-click the FINEPIX CD icon to open the FINEPIX
CD window and double-click setup or SETUP.EXE.
If the Installer Does Not Start Automatically (Windows 8)
1
2
3
4
68
Select Desktop on the Start screen.
Select File Explorer on the taskbar.
Select Computer in the navigation pane.
Double-click the drive icon inserting the FINEPIX CD and follow the on-screen
instructions to install.
Connections
Viewing Pictures on a Computer
4 If prompted to install Windows Media Player or DirectX, follow the onscreen instructions to complete installation.
5 Remove the installer CD from the CD-ROM drive when installation is
complete. Store the installer CD in a dry location out of direct sunlight in
case you need to re-install the software.
Installation is now complete. Proceed to “Connecting the Camera” (P 70).
Connections
69
Viewing Pictures on a Computer
Connecting the Camera
1 If the pictures you wish to copy are stored on a memory card, insert the
card into the camera.
R Windows users may require the Windows CD when starting the software for
the first time.
Q Loss of power during transfer could result in loss of data or damage to internal
memory or the memory card. Charge the battery before connecting the camera.
2 Turn the camera off and connect the
supplied USB cable as shown, making
sure the connectors are fully inserted.
Connect the camera directly to the
computer; do not use a USB hub or
keyboard.
Q Be sure the battery-chamber cover is open before attempting to open or close
the connector cover.
3 Press the a button for about a second to turn the camera on and follow
the on-screen instructions to copy pictures to the computer. To exit
without copying pictures, click Cancel.
70
Connections
Viewing Pictures on a Computer
For more information on using the supplied software, start the application
and select the appropriate option from the Help menu.
Q If a memory card containing a large number of images is inserted, there may be a
delay before the software starts and you may be unable to import or save images.
Use a memory card reader to transfer pictures.
Q Make sure that the computer does not display a message stating that copying is in
progress before turning the camera off or disconnecting the USB cable. Failure to
observe this precaution could result in loss of data or damage to internal memory
or the memory card.
Q Disconnect the camera before inserting or removing memory cards.
Q In some cases, it may not be possible to access pictures saved to a network server
using the supplied software in the same way as on a standalone computer.
Q The user bears all applicable fees charged by the phone company or Internet
service provider when using services that require an Internet connection.
Connections
71
Viewing Pictures on a Computer
Uninstalling the Supplied Software
Only uninstall the supplied software when it is no longer required or before
beginning reinstallation. After quitting the software and disconnecting the camera,
open the control panel and use “Programs and Features” (Windows 8/Windows 7/
Windows Vista) or “Add or Remove Programs” (Windows XP) to uninstall MyFinePix
Studio. Under Windows, one or more confirmation dialogs may be displayed; read
the contents carefully before clicking OK.
Importing pictures or movies to Mac (Macintosh)
Use a standard application in Mac OS such as Image Capture to import
pictures or movies to Mac.
72
Connections
Menus
Using the Menus: Shooting Mode
Using the Shooting Menu
To display the shooting menu, press MENU/OK in
shooting mode. Highlight items and press the
selector right to view options, then highlight an
option and press MENU/OK. Press DISP/BACK to exit
when settings are complete. The options available
vary with the shooting mode selected.
Shooting Menu Options
A SHOOTING MODE
Choose a shooting mode according to the type of subject (P 25).
(default: Q)
(default: AUTO)
N ISO
Control the camera’s sensitivity to light. Higher values can reduce blur; note, however, that
mottling may appear in pictures taken at high sensitivities.
100
Bright
Less noticeable
ISO
Scene
Noise (mottling)
6400
Dark
More noticeable
Option
Description
AUTO / AUTO (1600) / Sensitivity is adjusted automatically in response to shooting conditions,
AUTO (800) / AUTO (400) but will not be raised above the value in parentheses.
6400 / 3200 / 1600 / 800 /
Sensitivity is set to the specified value, which is shown in the display.
400 / 200 / 100
73
Using the Menus: Shooting Mode
O IMAGE SIZE
Choose the image size (large, medium, or small) and aspect ratio (4 : 3,
3 : 2, 16 : 9, or 1 : 1) at which pictures are recorded. Large pictures can be
printed at large sizes with no drop in quality, while small pictures require
less memory, allowing more pictures to be recorded.
(default: O 4:3)
O4:3
Size
Aspect ratio
Size Versus Aspect Ratio
Size
Option
O
P
Q
Prints at sizes up to
34 × 25 cm (13.5 × 10 in.)
24 × 18 cm (9.5 × 7 in.)
17 × 13 cm (7 × 5 in.)
4 : 3: Pictures have the same
proportions as the camera
display.
3
2
4
74
Aspect ratio
3 : 2: Pictures have the same
proportions as a frame of
35 mm film.
16 : 9: Suited for display on
High Definition (HD) devices.
9
3
16
Menus
Using the Menus: Shooting Mode
T IMAGE QUALITY
Choose how much image files are compressed.
Option
FINE
NORMAL
Description
Low compression. Select for higher image quality.
High compression. Select this option to store more pictures.
P FINEPIX COLOR
Enhance contrast and color saturation or take pictures in black and white.
Option
c STANDARD
a CHROME
b B&W
f SEPIA
(default: N)
(default: c)
Description
Standard contrast and saturation. Recommended in most situations.
Vivid contrast and color. Choose for vivid shots of flowers or enhanced greens
and blues in landscapes.
Take pictures in black and white.
Take pictures in sepia.
R Settings other than c STANDARD are shown by an icon in the LCD monitor.
R Depending on the subject, the effects of a CHROME may not be visible in the LCD monitor.
Menus
75
Using the Menus: Shooting Mode
D WHITE BALANCE
For natural colors, choose a setting that matches the light source.
Option
AUTO
i
j
k
l
m
n
g
(default: AUTO)
Description
White balance adjusted automatically.
For subjects in direct sunlight.
For subjects in the shade.
Use under “daylight” fluorescent lights.
Use under “warm white” fluorescent lights.
Use under “cool white” fluorescent lights.
Use under incandescent lighting.
For underwater photography.
R Results vary with shooting conditions. Play pictures back after shooting to check colors in
the LCD monitor.
76
Menus
Using the Menus: Shooting Mode
R CONTINUOUS
Capture motion in a series of pictures.
(default: J)
Option
Description
P CONTINUOUS
J CONTINUOUS
The camera takes pictures while the shutter button is pressed.
K CONTINUOUS
O CONTINUOUS
M FINAL
The camera shoots while the shutter button is pressed and records the last
N FINAL
several pictures.
Q FINAL
R
R
R
R
R
R
See page 115 for the frame rate and number of pictures taken in each mode.
Focus and exposure are determined by the first frame in each series.
In P mode, O IMAGE SIZE is fixed at Q 16 : 9.
The flash turns off automatically.
Frame rate varies with shutter speed.
The number of pictures that can be recorded depends on the memory available.
b FACE DETECTION
Choose whether the camera automatically detects and sets focus and exposure for human
portrait subjects (P 35).
Menus
77
Using the Menus: Shooting Mode
F AF MODE
This option controls how the camera selects the focus area. Regardless of the option selected,
the camera will focus on the subject in the center of the LCD monitor when macro mode is on.
Option
r CENTER
s MULTI
x TRACKING
Description
The camera focuses on the subject in the center of the frame.
When the shutter button is pressed halfway, the camera detects high-contrast
subjects near the center of the frame and selects the focus area automatically.
Position the subject in the center focus area and press the selector left. Focus
will track the subject as it moves through the frame.
R Note that in x mode, the camera focuses continuously, increasing the drain on the battery,
and that the sound of the camera focusing may be audible.
F MOVIE
F
MOVIE AF MODE
This option controls how the camera selects the focus area for movies.
Option
r CENTER
Description
The camera focuses on the subject in the center of the frame.
The camera continuously adjusts focus to reflect changes in the distance to
u CONTINUOUS
subjects near the center of the frame.
R Note that in u mode, the camera focuses continuously, increasing the drain on the battery,
and that the sound of the camera focusing may be audible.
78
Menus
Using the Menus: Shooting Mode
W MOVIE MODE
Choose a frame size for movies.
(default: i)
Option
Description
i 1920 × 1080 (60fps)
h 1280 × 720 (60fps)
f 640 × 480 (30fps)
k 640 × 480 (120 fps)
k 320 × 240 (240 fps)
k 224 × 168 (360 fps)
Full HD (High Definition).
High Definition.
Standard definition.
High speed movie. Sound is not recorded, and focus, exposure, and
white balance are not adjusted automatically.
(default: OFF)
q LED ILLUMINATOR
Choose whether the LED (P 2) lights to illuminate nearby subjects when lighting is poor.
Option
ON
OFF
R
R
R
R
Description
The LED lights during shooting.
LED off.
The LED will not light when ON is selected for o SILENT MODE in the setup menu (P 90).
Selecting ON increases the drain on the battery. Select OFF when the LED is not in use.
q LED ILLUMINATOR is automatically reset to OFF when the camera is turned off.
The LED turns off if no operations are performed for a short period. Operating any of the
camera controls reactivates the LED.
Menus
79
Using the Menus: Playback Mode
Using the Playback Menu
To display the playback menu, press MENU/OK in
playback mode. Highlight items and press the
selector right to view options, then highlight an
option and press MENU/OK. Press DISP/BACK to exit
when settings are complete.
Playback Menu Options
r WIRELESS TRANSFER
Connect via a wireless network to upload pictures to smartphones or tablets or to remotely
browse the pictures on the camera and select images for download (P 52).
s PC AUTO SAVE
58).
Upload pictures to a computer over a wireless network (P 58
U LOCATION INFO COPY
Copy location data from one picture to another.
k PHOTOBOOK ASSIST
Create books from your favorite photos (P 49).
b IMAGE SEARCH
Search for pictures (P 48).
A ERASE
Delete all or selected pictures (P 47).
80
Menus
Using the Menus: Playback Mode
n MOVIE EDIT
Edit movies.
Q Do not turn the camera off while editing movies.
■ MOVIE TRIMMING
Remove opening or ending footage to create an edited copy of the current movie.
1 Display the desired movie.
2 Select n MOVIE EDIT > MOVIE TRIMMING in the playback menu. To remove footage from
the start of the copy, proceed to Step 3; otherwise, proceed to Step 4.
3 Press the selector down to begin playback and press it down again when the new opening
frame is reached.
4 Press MENU/OK. To remove footage from the end of the copy, proceed to Step 5; otherwise,
proceed to Step 6.
5 Press the selector down to begin playback and press it down again when the new closing
frame is reached.
6 Press MENU/OK to save the copy.
■ MOVIE JOIN
Add existing footage to the end of the current movie to create an edited copy.
1 Display the desired movie.
2 Select n MOVIE EDIT > MOVIE JOIN in the playback menu.
3 Press the selector left or right to highlight a movie.
4 Press MENU/OK to add the highlighted footage to the end of the current movie and save the
resulting copy, or press DISP/BACK to exit without creating a copy.
R Both movies must have been recorded at the same frame size and frame rate.
Menus
81
Using the Menus: Playback Mode
j MARK FOR UPLOAD TO
Select pictures for upload to YouTube, Facebook or MyFinePix.com using MyFinePix Studio
(Windows only).
■ Selecting Pictures for Upload
1 Select YouTube to choose movies for upload to YouTube, FACEBOOK to choose photos and
movies for upload to Facebook, or MyFinePix.com to choose photos for upload to MyFinePix.com.
2 Press the selector left or right to display pictures and press MENU/OK to select or deselect. Press
DISP/BACK to exit when all the desired pictures are selected.
R Only movies can be selected for upload to YouTube.
R Only photos can be selected for upload to MyFinePix.com.
R During playback, selected pictures are indicated by j YouTube, j FACEBOOK or
j MyFinePix.com icons.
■ RESET ALL: Deselecting All Pictures
Choose RESET ALL to deselect all pictures. If the number of pictures affected is very large, a
message will be displayed while the operation is in progress. Press DISP/BACK to exit before the
operation is complete.
■ Uploading Pictures (Windows Only)
Selected pictures can be uploaded using the YouTube/Facebook/MyFinePix.com Upload
option in MyFinePix Studio.
Select with camera
Upload from computer
For information on installing MyFinePix Studio and connecting the camera to a computer, see
“Viewing Pictures on a Computer” (P 67).
82
Menus
Using the Menus: Playback Mode
I SLIDE SHOW
View pictures in an automated slide show. Choose the type of show and press MENU/OK to start.
Press DISP/BACK at any time during the show to view on-screen help. The show can be ended at
any time by pressing MENU/OK.
Option
NORMAL
FADE-IN
NORMAL g
FADE-IN g
Description
Press selector left or right to go back or skip ahead one frame. Select FADE-IN
for fade transitions between frames.
As above, except that camera automatically zooms in on faces selected with
Intelligent Face detection.
R The camera will not turn off automatically while a slide show is in progress.
B RED EYE REMOVAL
If the current picture is marked with a g icon to indicate that it was taken with Intelligent Face
Detection, this option can be used to remove red-eye. The camera will analyze the image; if redeye is detected, the image will be processed to create a copy with reduced red-eye.
1 Display the desired picture.
2 Select B RED EYE REMOVAL in the playback menu.
3 Press MENU/OK.
R Red eye may not be removed if the camera is unable to detect a face or the face is in profile.
Results may differ depending on the scene. Red eye can not be removed from pictures that
have already been processed using red-eye removal or pictures created with other devices.
R The amount of time needed to process the image varies with the number of faces detected.
R Copies created with B RED EYE REMOVAL are indicated by a e icon during playback.
Menus
83
Using the Menus: Playback Mode
D PROTECT
Protect pictures from accidental deletion.
1 Select D PROTECT in the playback menu.
2 Highlight one of the following options and press MENU/OK:
• FRAME: Protect selected pictures. Press the selector left or right to view pictures and press
MENU/OK to select or deselect. Press DISP/BACK when the operation is complete.
• SET ALL: Protect all pictures.
• RESET ALL: Remove protection from all pictures.
Q Protected pictures will be deleted when the memory card or internal memory is formatted
(P 91).
G CROP
Create a cropped copy of the current picture.
1 Display the desired picture.
2 Select G CROP in the playback menu.
3 Use the zoom buttons to zoom in and out and use the selector to scroll the picture until the
desired portion is displayed.
4 Press MENU/OK to display a confirmation dialog.
5 Press MENU/OK again to save the cropped copy to a separate file.
R Larger crops produce larger copies. If the size of the final copy will be a, YES will be
displayed in yellow.
84
Menus
Using the Menus: Playback Mode
O RESIZE
Create a small copy of the current picture.
1 Display the desired picture.
2 Select O RESIZE in the playback menu.
3 Highlight a size and press MENU/OK to display a confirmation dialog.
4 Press MENU/OK to save the resized copy to a separate file.
R The sizes available vary with the size of the original image.
C IMAGE ROTATE
Rotate pictures taken in tall orientation so that they are displayed in tall orientation in the LCD
monitor.
1 Display the desired picture.
2 Select C IMAGE ROTATE in the playback menu.
3 Press the selector down to rotate the picture 90 ° clockwise, up to rotate it 90 ° counterclockwise.
4 Press MENU/OK. The picture automatically be displayed in the selected orientation whenever
it is played back on the camera.
R Protected pictures can not be rotated. Remove protection before rotating pictures (P 84).
R The camera may not be able to rotate pictures created with other devices.
Menus
85
Using the Menus: Playback Mode
E COPY
Copy pictures from internal memory to a memory card.
1 Select E COPY in the playback menu.
2 Highlight one of the following options and press the selector right:
• a INTERNAL MEMORY y b CARD: Copy pictures from internal memory to a memory card.
• b CARD y a INTERNAL MEMORY: Copy pictures from a memory card to internal memory.
3 Press the selector left or right to view pictures and press MENU/OK to copy the current picture.
R Copying ends when the destination is full.
R DPOF print information is not copied (P 65).
K PRINT ORDER (DPOF)
Select pictures for printing on DPOF- and PictBridge-compatible devices (P 65).
86
Menus
Using the Menus: Playback Mode
J DISP ASPECT
Choose how High Definition (HD) devices display pictures with an aspect ratio of 4 : 3 (this option
is available only when an HDMI cable is connected). Select 16 : 9 to display the image so that it
fills the screen with its top and bottom cropped out, 4 : 3 to display the entire image with black
bands at either side.
16 : 9
4:3
16 : 9
4:3
R Photographs with an aspect ratio of 16 : 9 are displayed full screen, those with an aspect ratio
of 3 : 2 in a black frame.
Menus
87
The Setup Menu
Using the Setup Menu
1 Display the setup menu.
1.1 Press MENU/OK to display the menu for the
current mode.
1.2 Press the selector left to highlight the tab for
the current menu.
SET-UP
SET
SET
EXIT
Tab
1.3 Press the selector down to highlight X.
1.4 Press the selector right to place the cursor in the setup menu.
2 Adjust settings.
Highlight items and press the selector right to view options, then highlight
an option and press MENU/OK. Press DISP/BACK to exit when settings are
complete.
88
Menus
The Setup Menu
Setup Menu Options
F DATE/TIME
Set the camera clock (P 19).
N TIME DIFFERENCE
(default: h)
Switch the camera clock instantly from your home time zone to the local time at your destination
when traveling. To specify the difference between local time and your home time zone:
1 Highlight g LOCAL and press the selector right.
2 Use the selector to choose the time difference between local time and your home time zone
in increments of 15 minutes.
3 Press MENU/OK.
To switch between local time and your home time zone, highlight g LOCAL or h HOME and
press MENU/OK.
Option
h HOME
g LOCAL
Description
Switch to the time currently selected for F DATE/TIME (see above).
Switch to local time. If this option is selected, g and the time and date will be
displayed in yellow for three seconds each time the camera is turned on.
La
Choose a language.
Menus
89
The Setup Menu
r WIRELESS SETTINGS
Adjust settings for connection to a wireless network.
Option
GENERAL SETTINGS
RESIZE IMAGE FOR
SMARTPHONE H
PC AUTO SAVE
SETTINGS
Description
Choose NAME a name to identify the camera on the wireless network (the
camera is assigned a unique name by default) or select RESET WIRELESS
SETTINGS to restore default settings.
Choose ON (the default setting, recommended in most circumstances)
to resize larger images to H for upload to smartphones, OFF to upload
images at their original size. Resizing applies only to the copy uploaded to
the smartphone; the original is not affected.
Choose DELETE REGISTERED DESTINATION PC to remove selected
destinations, DETAILS OF PREVIOUS CONNECTION to view computers to
which the camera has recently connected.
s PC AUTO SAVE SETTING
Choose a destination for images uploaded using s PC AUTO SAVE. For more information, visit
http://app.fujifilm-dsc.com/pc.
U GEOTAGGING SET-UP
Access the following location data options (P 54).
Option
Description
LOCATION INFO SEARCH Download location data from a smartphone.
GEOTAGGING
Choose whether to save location data with pictures.
LOCATION INFO
Display location data.
(default: OFF)
o SILENT MODE
Select ON to disable the speaker, flash, AF-assist illuminator, and LED illuminator in situations in
which camera sounds or lights may be unwelcome (note that the flash will still fire in C mode).
90
Menus
The Setup Menu
R RESET
Reset all settings except F DATE/TIME, N TIME DIFFERENCE, and O BACKGROUND COLOR
to default values.
1 Highlight R RESET and press the selector right to display a confirmation dialog.
2 Highlight OK and press MENU/OK.
K FORMAT
If a memory card is inserted in the camera, this option will format the memory card. If no
memory card is inserted, this option will format internal memory. Select OK to begin formatting.
Q All data—including protected pictures—will be deleted from the memory card or internal
memory. Be sure important files have been copied to a computer or other storage device.
Q Do not open the battery cover during formatting.
A IMAGE DISP.
Choose how long pictures are displayed in the LCD monitor after shooting.
Option
3 SEC
1.5 SEC
ZOOM (CONTINUOUS)
OFF
(default: 1.5 SEC)
Description
Pictures are displayed for three seconds (3 SEC) or 1.5 seconds (1.5 SEC).
Colors may differ slightly from those in the final image.
Pictures are displayed until the MENU/OK button is pressed.
Pictures are not displayed after shooting.
R OFF has no effect in continuous shooting, Y ADVANCED FILTER, and i INDIVID.
SHUTTER 3D modes.
Menus
91
The Setup Menu
(default: CONT.)
B FRAME NO.
New pictures are stored in image files named using a four-digit file
Frame number
number assigned by adding one to the last file number used. The file
100-0001
number is displayed during playback as shown at right. B FRAME NO.
controls whether file numbering is reset to 0001 when a new memory Directory
File
card is inserted or the current memory card or internal memory is number
number
formatted.
Option
CONTINUOUS
RENEW
Description
Numbering continues from the last file number used or the first available file
number, whichever is higher. Choose this option to reduce the number of
pictures with duplicate file names.
Numbering is reset to 0001 after formatting or when a new memory card is
inserted.
R If the frame number reaches 999-9999, the shutter release will be disabled (P 111).
R Selecting R RESET (P 91) sets B FRAME NO. to CONTINUOUS but does not reset the file
number.
R Frame numbers for pictures taken with other cameras may differ.
92
Menus
The Setup Menu
G OPERATION VOL.
(default: c)
Adjust the volume of the sounds produced when camera controls are operated. Choose f
(mute) to disable control sounds.
H SHUTTER VOLUME
(default: c)
Adjust the volume of the sounds produced when the shutter is released. Choose f (mute)
to disable the shutter sound.
e SOUND
Choose the sounds used for the shutter, at startup, and for camera controls.
I PLAYBACK VOLUME
Adjust the volume for movie playback.
J LCD BRIGHTNESS
Control the brightness of the display.
Option
AUTO
MANUAL
Menus
(default: i)
(default: 7)
(default: AUTO)
Description
Display brightness is automatically adjusted during shooting in response to
ambient lighting conditions. Brightness is not adjusted during playback.
Press the selector up or down to adjust brightness and then press MENU/OK.
Choose from values between –5 and +5.
93
The Setup Menu
E LCD MODE
(default: U ON)
Choose whether the display automatically dims to save power in shooting mode. This option
does not take effect during playback.
Option
Description
The display dims to save power if no operations are performed for a few
U POWER SAVE ON seconds. Normal brightness can be restored by pressing the shutter button
halfway.
U POWER SAVE OFF Automatic dimming off.
(default: 2 MIN)
M AUTO POWER OFF
Choose the length of time before the camera turns off automatically when no operations are
performed. Shorter times increase battery life; if OFF is selected, the camera must be turned
off manually. Note that in some situations the camera turns off automatically even when OFF
is selected.
(default: OFF)
1 QUICK START MODE
Allow the camera to restart in a fast manner after turned off (24MIN/10 MIN/OFF). After
specified time has passed, the camera will discontinue this option.
Q This option will increase drain on the battery.
L DUAL IS MODE
(default: l)
Choose whether image stabilization is performed at all times when the camera is in shooting
mode (l CONTINUOUS), or only when the shutter button is pressed halfway (m SHOOTING
ONLY). Choose OFF to turn image stabilization off when using a tripod.
94
Menus
The Setup Menu
(default: ON)
B RED EYE REMOVAL
Choose ON to remove red-eye effects caused by the flash when shooting with Intelligent Face
Detection.
R Red-eye reduction is performed only when a face is detected.
(default: OFF)
R INTELLIGENT DIGITAL ZOOM
If ON is selected, selecting T at the maximum optical zoom position triggers intelligent digital
zoom, further magnifying the image while processing it for sharp, high-resolution results.
The Zoom Indicator
W
INTELLIGENT DIGITAL
ZOOM on
T
Optical zoom
W
INTELLIGENT DIGITAL
ZOOM off
Intelligent
digital zoom
T
Optical zoom
R Selecting another mode may end intelligent digital zoom.
R When combined with optical zoom, intelligent digital zoom offers zoom factors as high as
10×.
R Intelligent digital zoom may sometimes produce lower quality images than optical zoom.
R The time needed to record images increases.
R The effects are not visible in the display during shooting.
R Intelligent digital zoom is not available in continuous mode or during movie recording.
Menus
95
The Setup Menu
p MOVIE ZOOM TYPE
(default: D)
Choose the type of zoom available during movie recording: C DIGITAL or D OPTICAL.
R Movies recorded using digital zoom may be slightly “grainy”.
(default: ON)
C AF ILLUMINATOR
If ON is selected, the AF-assist illuminator will light to assist autofocus.
Q The camera may be unable to focus using the AF-assist illuminator in some cases. If the
camera is unable to focus in macro mode, try increasing the distance to the subject.
Q Avoid shining the AF-assist illuminator directly into your subject’s eyes.
(default: ON)
m AUTOROTATE PB
Choose ON to automatically rotate “tall” (portrait-orientation) pictures during playback.
O BACKGROUND COLOR
Choose a color scheme.
c GUIDANCE DISPLAY
Choose whether to display tool tips.
96
(default: ON)
Menus
The Setup Menu
U DATE STAMP
Stamp the time and/or date of recording on photographs as they are taken.
Option
R+S
R
OFF
(default: OFF)
Description
Stamp new photographs with the date and time of recording.
Stamp new photographs with the date of recording.
Do not stamp the time and date on new photographs.
Q Time and date stamps can not be deleted. Turn U DATE STAMP off to prevent time and date
stamps appearing on new photographs.
Q If the camera clock is not set, you will be prompted to set the clock to the current date and
time (P 19).
Q We recommend that you turn the DPOF “print date” option off when printing images with a
time and date stamp (P 65).
Q Time and date stamps do not appear on movies, panoramas, or 3D photos.
Menus
97
Technical Notes
Optional Accessories
The camera supports a wide range of accessories from FUJIFILM and other
manufacturers.
DIGITAL CAMERA
■ Printing
FINEPIX XP200 Series
■ Audio/Visual
HDMI cable (sold separately)
USB cable
(supplied)
PictBridge-compatible
printer *
HDTV *
SD/SDHC/SDXC
memory card
Printer *
■ Digital viewer
Supports 3D display of
pictures taken using
INDIVD. SHUTTER 3D.
FINEPIX REAL 3D V3 (sold separately)
■ Computer Related
USB cable (supplied)
SD card slot or card reader
Computer *
* Available separately.
98
Optional Accessories
Accessories from FUJIFILM
The following optional accessories are available from FUJIFILM. For the latest
information on the accessories available in your region, check with your local
FUJIFILM representative or visit http://www.fujifilm.com/products/digital_
cameras/index.html.
Rechargeable NP-50: Additional large-capacity NP-50 rechargeable
Li-ion batteries batteries can be purchased as required.
Battery
chargers
BC-45W: Replacement battery chargers can be purchased
as required. The BC-45W charges an NP-50 battery in
about 150 minutes at +20 °C (+68 °F).
Digital viewer FINEPIX REAL 3D V3:
V3 View 3D images without 3D glasses.
Technical Notes
99
Caring for the Camera
To ensure continued enjoyment of the product, observe the following
precautions.
Storage and Use
If the camera will not be used for an
extended period, remove the battery
and memory card. Do not store or
use the camera in locations that are:
• exposed to rain, steam, or smoke
• very humid or extremely dusty
• exposed to direct sunlight or very
high temperatures, such as in a
closed vehicle on a sunny day
• extremely cold
• subject to strong vibration
• exposed to strong magnetic
fields, such as near a broadcasting
antenna, power line, radar emitter,
motor, transformer, or magnet
• in contact with volatile chemicals
such as pesticides
• next to rubber or vinyl products
100
■ Condensation
Sudden increases in temperature,
such as occur when entering a heated
building on a cold day, can cause
condensation inside the camera. If
this occurs, turn the camera off and
wait an hour before turning it on
again. If condensation forms on the
memory card, remove the card and
wait for the condensation to dissipate.
Technical Notes
Caring for the Camera
Cleaning
Use a blower to remove dust from the protective glass covering the lens and
LCD monitor, then gently wipe with a soft, dry cloth. Any remaining stains can
be removed by wiping gently with a piece of FUJIFILM lens-cleaning paper to
which a small amount of lens-cleaning fluid has been applied. Care should
be taken to avoid scratching the protective glass or LCD monitor. The camera
body can be cleaned with a soft, dry cloth. Do not use alcohol, thinner, or
other volatile chemicals.
Traveling
Keep the camera in your carry-on baggage. Checked baggage may suffer
violent shocks that could damage the camera.
Technical Notes
101
Troubleshooting
Problems and Solutions
Water in the Camera
Problem
Water in the camera.
Solution
The battery-chamber cover was not fully closed before the camera was immersed, or
was opened under water
water:: Take the camera to a FUJIFILM-authorized service technician for
repairs. Do not turn the camera on.
Power and Battery
Problem
The camera does not
turn on.
•
•
•
•
•
The battery runs down
quickly.
•
•
•
The camera turns off
suddenly.
Charging is slow.
102
Solution
The battery is exhausted
exhausted:: Charge the battery or insert a fully-charged spare battery ((P
P 7, 14).
The battery is inserted incorrectly:
incorrectly: Reinsert in the correct orientation (P
(P 8).
The battery-chamber cover is not latched
latched:: Latch the battery-chamber cover (P
(P 10).
The battery is cold
cold:: Warm the battery by placing it in a pocket or other warm place and reinsert
it in the camera immediately before taking a picture.
There is dirt on the battery terminals
terminals:: Clean the terminals with a soft, dry cloth.
Q is selected for shooting mode:
mode: Select B mode to reduce the drain on the battery
(P 25).
x TRACKING is selected for F AF MODE:
MODE: Select a different AF mode ((P
P 78).
The battery has been charged many times
times:: The battery has reached the end of its charging
life. Purchase a new battery.
Charge the battery or insert a fully-charged spare battery ((P
P 7, 14).
Charge the battery at room temperature (P
(P vi).
Problems and Solutions
Problem
The battery does not
charge. / The self-timer
lamp flashes.
Solution
Reinsert the battery in the correct orientation and make sure that the power connection is made
(P 7, 14).
• There is dirt on the battery terminals
terminals:: Clean the terminals with a soft, dry cloth.
• The battery has been charged many times
times:: The battery has reached the end of its charging
life. Purchase a new battery. If the battery still fails to charge, contact your FUJIFILM dealer.
• The battery is too hot or too cold
cold:: Wait for the battery temperature to stabilize (P
(P 14).
Menus and Displays
Problem
Menus and displays are
not in English.
Solution
Select ENGLISH for L a ((P
P 19, 89).
Shooting
Problem
•
•
No picture is taken when
•
the shutter button is
•
pressed.
•
•
•
The camera does not
•
focus.
•
Troubleshooting
Solution
Memory is full:
full: Insert a new memory card or delete pictures ((P
P 9, 47).
Memory is not formatted:
formatted: Format the memory card or internal memory ((P
P 91).
There is dirt on the memory card contacts
contacts:: Clean the contacts with a soft, dry cloth.
The memory card is damaged
damaged:: Insert a new memory card (P
(P 9).
The battery is exhausted
exhausted:: Charge the battery or insert a fully-charged spare battery ((P
P 7, 14).
The camera has turned off automatically
automatically:: Turn the camera on ((P
P 17).
The subject is close to the camera
camera:: Select macro mode (P
(P 39).
The subject is far away from the camera
camera:: Cancel macro mode (P
(P 39).
The subject is not suited to autofocus
autofocus:: Use focus lock ((P
P 36).
103
Problems and Solutions
Problem
Solution
Macro mode is not
Choose a different shooting mode ((P
P 25).
available.
Intelligent Face Detection
Choose a different shooting mode ((P
P 25).
is not available.
• The subject’s face is obscured by sunglasses, a hat, long hair, or other objects:
objects: Remove
the obstructions.
• The subject’s face occupies only a small area of the frame
frame:: Change the composition so that
No face is detected.
the subject’s face occupies a larger area of the frame ((P
P 35).
• The subject’s head is tilted or horizontal
horizontal:: Ask the subject to hold their head straight.
• The camera is tilted
tilted:: Keep the camera level (P
(P 21).
• The subject’s face is poorly lit
lit:: Shoot in bright light.
Wrong subject is
The selected subject is closer to the center of the frame than the main subject. Recompose the
selected.
picture or turn face detection off and frame the picture using focus lock (P
(P 36).
3D images do not turn Use a tripod or change the distance the camera is moved between the first and second shots
out as expected.
(P 33).
• The flash is not available in the current shooting mode
mode:: Choose a different shooting mode
(P 25).
• The battery is exhausted
exhausted:: Charge the battery or insert a fully-charged spare battery ((P
P 7, 14).
The flash does not fire. • The camera is in continuous mode
mode:: Press the burst mode button to select single-frame mode
(P 43).
• The camera is in silent mode
mode:: Turn silent mode off (P
(P 90).
• The flash is off (P): Choose a different flash mode ((P
P 40).
104
Troubleshooting
Problems and Solutions
Problem
Solution
• The desired flash mode is not available in the current shooting mode
mode:: Choose a different
Some flash modes are
shooting mode (P
(P 25).
not available.
• The camera is in silent mode
mode:: Turn silent mode off (P
(P 90).
The flash does not fully • The subject is not in range of the flash
flash:: Position the subject in range of the flash (P
(P 116).
light the subject.
• The flash window is obstructed
obstructed:: Hold the camera correctly ((P
P 21).
• The protective glass covering the lens is dirty
dirty:: Clean the glass ((P
P 101).
• The protective glass covering the lens is blocked:
blocked: Keep objects away from the lens ((P
P 21).
Pictures are blurred.
• s is displayed during shooting and the focus frame is displayed in red:
red: Check focus
before shooting ((P
P 109).
• k is displayed during shooting:
shooting: Use the flash or a tripod (P
(P 41).
• A slow shutter speed is selected at high temperatures:
temperatures: This is normal and does not
indicated a malfunction.
Pictures are mottled.
• The camera has been used continuously at high temperatures or a temperature
warning is displayed:
displayed: Turn the camera off and wait for it to cool down.
Vertical lines appear in The camera has been used continuously at high temperatures. Turn the camera off and wait for
pictures.
it to cool down.
“Smear” in the form of Vertical purple or white lines may appear after the camera has been used continuously at high
vertical purple or white temperatures or when a very bright object is in the frame; this phenomenon is common to all CCD
lines appears in the
image sensors and does not indicate a malfunction. These lines are recorded in movies but do not
display.
appear in photographs. Avoid framing bright objects when filming movies.
Location data
Location data are incorrect. The camera has been moved since location data were last updated.
• u CONTINUOUS is selected for F MOVIE AF MODE
MODE:: Select a different AF mode
Sounds made by the
(P 78).
camera are recorded with
• Zoom was adjusted during shooting
shooting:: Do not adjust zoom during shooting.
movies.
• Intelligent Face Detection is on:
on: Turn Intelligent Face Detection off (P
(P 35).
Troubleshooting
105
Problems and Solutions
Playback
Problem
Pictures are grainy.
Playback zoom is
unavailable.
Solution
The pictures were taken with a different make or model of camera.
The current picture is a resized copy with a size of a.
• Playback volume is too low:
low: Adjust playback volume (P
(P 93).
• The microphone was obstructed
obstructed:: Hold the camera correctly during recording ((P
P 21, 59).
• The speaker is obstructed
obstructed:: Hold the camera correctly during playback ((P
P 61).
Selected pictures are not Some of the pictures selected for deletion are protected. Remove protection using the device with
deleted.
which it was originally applied (P
(P 84).
File numbering is
The battery-chamber cover was opened while the camera was on. Turn the camera off before
unexpectedly reset.
opening the battery-chamber cover (P
(P 17).
No sound in movie
playback.
106
Troubleshooting
Problems and Solutions
Connections/Miscellaneous
Problem
Problem connecting or
uploading pictures to
smartphone.
Can not upload images.
Smartphone will not
display pictures.
No picture or sound.
The computer does not
recognize the camera.
Pictures can not be
printed.
Only one copy is printed/
the date is not printed.
Solution
• The smartphone is too far away:
away: Move the devices closer.
• Nearby devices are causing radio interference:
interference: Move the camera and smartphone away
from microwave ovens or cordless phones.
• The smartphone is connected to another device:
device: The smartphone and camera can connect
to only one device at a time. End the connection and try again.
• There are several smartphones in the vicinity
vicinity:: Try connecting again. The presence of
multiple smartphones can make connection difficult.
The current image is a movie or was created on another device and can not be uploaded to a
smartphone.
Select ON for r WIRELESS SETTING
SETTING >
> RESIZE IMAGE FOR SMARTPHONE
H. Selecting OFF increases upload times for larger images; in addition, some phones may not
display images over a certain size.
• The camera is not properly connected
connected:: Connect the camera properly (P
(P 62).
• Input on the television is set to “TV”:
“TV”: Set input to “HDMI”.
• The volume on the TV is too low:
low: Adjust the volume.
Be sure the camera and computer are correctly connected ((P
P 70).
• The camera is not properly connected
connected:: Connect the camera correctly (P
(P 63).
• The printer is off
off:: Turn the printer on.
The printer is not PictBridge compatible.
The camera is
unresponsive.
• Temporary camera malfunction:
malfunction: Remove and reinsert the battery (P
(P 7).
• The battery is exhausted
exhausted:: Charge the battery ((P
P 14) or insert a fully-charged spare battery
(P 7).
The camera does not
function as expected.
Remove and reinsert the battery (P
(P 7). If the problem persists, contact your FUJIFILM dealer.
Troubleshooting
107
Problems and Solutions
Problem
No sound.
Time and date stamps
108
Solution
Turn silent mode off (P
(P 90).
• Time and date stamps are not correct:
correct: Set the camera clock (P
(P 19).
• Time and date stamps appear on photographs:
photographs: Time and date stamps can not be deleted. To
prevent stamps appearing on new photographs, select OFF for U DATE STAMP ((P
P 97).
Troubleshooting
Warning Messages and Displays
The following warnings are displayed in the LCD monitor:
Warning
B ((red
red))
A ((blinks
blinks red)
red)
k
s
(displayed in red with red
focus frame)
frame)
r
Aperture or shutter speed
displayed in red
FOCUS ERROR
TURN OFF THE CAMERA
AND TURN ON AGAIN
LENS CONTROL ERROR
CARD NOT INITIALIZED
PROTECTED CARD
BUSY
Troubleshooting
Description
Low battery. Charge the battery ((P
P 14) or insert a fully-charged spare battery ((P
P 7).
Battery exhausted. Charge the battery (P
(P 14) or insert a fully-charged spare battery ((P
P 7).
Slow shutter speed. Pictures may be blurred; use the flash or a tripod.
The camera can not focus. Try one of the following solutions:
• Use focus lock to focus on another subject at the same distance, then recompose the picture
(P 36).
• Use macro mode to focus when taking close-ups (P
(P 39).
The subject is too bright or too dark and the picture will be over- or under-exposed. If the subject
is dark, use the flash (P
(P 40).
Camera malfunction or moving parts of lens obstructed. Turn the camera off and then on again,
taking care not to touch the lens. If the message persists, contact a FUJIFILM dealer.
• The memory card or internal memory is not formatted or the memory card was
formatted in a computer or other device:
device: Format the memory card or internal memory
using the K FORMAT option in the camera setup menu (P
(P 91).
• The memory card contacts require cleaning
cleaning:: Clean the contacts with a soft, dry cloth. If
the message is repeated, format the card (P
(P 91). If the message persists, replace the card.
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
The memory card is locked. Unlock the card ((P
P 9).
The memory card is incorrectly formatted. Use the camera to format the card (P
(P 91).
109
Warning Messages and Displays
Warning
p
CARD ERROR
a MEMORY FULL
b MEMORY FULL
INTERNAL MEMORY IS
FULL
INSERT A NEW CARD
WRITE ERROR
READ ERROR
110
Description
Turn the camera off and wait for it to cool. If no action is taken, the camera will turn off
automatically.
The memory card is not formatted for use in the camera. Format the card (P
(P 91).
The memory card contacts require cleaning or the memory card is damaged. Clean the contacts
with a soft, dry cloth. If the message is repeated, format the card ((P
P 91). If the message persists,
replace the card.
Incompatible memory card. Use a compatible card (P
(P 12).
Camera malfunction. Contact a FUJIFILM dealer.
The memory card or internal memory is full and pictures can not be recorded or copied. Delete
pictures or insert a memory card with more free space.
• Memory card error or connection error
error:: Reinsert the card or turn the camera off and then
on again. If the message persists, contact a FUJIFILM dealer.
• Not enough memory remaining to record additional pictures
pictures:: Delete pictures or insert
a memory card with more free space.
• The memory card or internal memory is not formatted:
formatted: Format the memory card or
internal memory (P
(P 91).
• The file is corrupt or was not created with the camera
camera:: The file can not be viewed.
• The memory card contacts require cleaning
cleaning:: Clean the contacts with a soft, dry cloth. If
the message is repeated, format the card (P
(P 91). If the message persists, replace the card.
• Camera malfunction:
malfunction: Contact a FUJIFILM dealer.
Troubleshooting
Warning Messages and Displays
Warning
FRAME NO. FULL
Description
The camera has run out of frame numbers (current frame number is 999-9999). Format the
memory card and select RENEW for B FRAME NO. in the setup menu. Take a picture
to reset frame numbering to 100-0001, then select CONTINUOUS for B FRAME NO
(P 92)
92)..
PRESS AND HOLD
An attempt was made to choose a flash mode or adjust the volume with the camera in silent
THE DISP BUTTON TO
mode. Exit silent mode before choosing a flash mode or adjusting the volume ((P
P 90).
DEACTIVATE SILENT MODE
A search has returned more than 5,000 results, or more than 999 frames were selected for
TOO MANY FRAMES
deletion. Perform a different search or select fewer pictures.
PROTECTED FRAME
An attempt was made to delete to a protected picture. Remove protection and try again (P
(P 84).
a pictures can not be cropped.
a CAN NOT CROP
CAN NOT CROP
The picture is damaged or was not created with the camera.
P CANNOT EXECUTE
An attempt was made to create a resized copy at a size equal to or larger than the original.
Q CANNOT EXECUTE
Choose a smaller size.
a CANNOT EXECUTE
CAN NOT ROTATE
An attempt was made to rotate a picture that can not be rotated.
F CAN NOT ROTATE Movies can not be rotated.
CANNOT EXECUTE
Red-eye removal can not be applied to the selected picture.
F CANNOT EXECUTE Red-eye removal can not be applied to movies.
Troubleshooting
111
Warning Messages and Displays
Warning
NO CARD
b NO IMAGE
a NO IMAGE
Description
No memory card inserted when E COPY is selected in the playback menu. Insert a memory
card.
The source selected for E COPY contains no images. Select a different source.
The DPOF print order on the current memory card contains more than 999 images. Copy the
pictures to internal memory and create a new print order.
CAN NOT SET DPOF
The picture can not be printed using DPOF.
F CAN NOT SET DPOF Movies can not be printed using DPOF.
A connection error occurred while pictures were being printed or copied to a computer or other
COMMUNICATION ERROR
device. Confirm that the device is turned on and that the USB cable is connected.
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details).
PRINTER ERROR
To resume printing, turn the printer off and then turn it back on.
PRINTER ERROR
Printer out of paper or ink, or other printer error. Check printer (see printer manual for details). If
RESUME?
printing does not resume automatically, press MENU/OK to resume.
An attempt was made to print a movie, a picture not created with the camera, or a picture in a
format not supported by the printer. Movies and some pictures created with other devices can
CANNOT BE PRINTED not be printed; if the picture is a still picture created with the camera, check the printer manual
to confirm that the printer supports the JFIF-JPEG or Exif-JPEG format. If it does not, the pictures
can not be printed.
Ensure the battery chamber Check that the battery-chamber cover is latched. Note that the cover may already be latched;
cover is locked.
this message merely encourages you to check that the cover is secure before proceeding.
DPOF FILE ERROR
112
Troubleshooting
Appendix
Memory Card Capacity
The following table shows the recording time or number of pictures available
at different image sizes. All figures are approximate; file size varies with the scene
recorded, producing wide variations in the number of files that can be stored. The
number of exposures or length remaining may not diminish at an even rate. A limited
number of test pictures can be taken when no memory card is inserted.
■ Photographs
O
FINE
4 GB
NORMAL
FINE
8 GB
NORMAL
4:3
500
980
1000
1980
3:2
560
1110
1120
2230
P
16 : 9
660
1310
1330
2640
1:1
660
1310
1330
2640
4:3
980
1940
1980
3900
Q
16 : 9
1300
2550
2610
5120
4:3
2450
4710
4910
9460
16 : 9
3600
6800
7230
13660
■ Movies
4 GB
8 GB
i 1920 × 1080 h 1280 × 720 f 640 × 480 k 640 × 480 k 320 × 240 k 224 × 168
(60 fps) 1
(60 fps) 1
(30 fps) 2
(120 fps) 3
(240 fps) 3
(360 fps) 3
21 min.
22 min.
78 min.
29 min.
40 min.
37 min.
42 min.
44 min.
157 min.
58 min.
81 min.
74 min.
1 Use a H card or better. Individual movies can not exceed 22 minutes in length.
2 Use a H card or better. Individual movies can not exceed 80 minutes in length.
3 Use a H card or better. Individual movies can not exceed 30 seconds in length.
113
Specifications
System
Model
Effective pixels
Image sensor
Storage media
File system
File format
Image size (pixels)
Lens
Focal length
Digital zoom
Aperture
Focus range
(distance from front of lens)
114
Digital Camera FinePix XP200 Series
16.4 million
1/2.3 -in. square pixel CMOS with primary color filter
• Internal memory
• SD/SDHC/SDXC memory cards
Compliant with Design Rule for Camera File System (DCF)
(DCF),, Exif 2.3, and Digital Print Order
Format (DPOF)
• Still pictures:
pictures: Exif 2.3 JPEG (compressed)
• Still pictures (3D)
(3D):: MPO
• Movies
Movies:: H.264 standard with linear PCM stereo sound (MOV)
• O 4 : 3:
3: 4,608 × 3,456
• O 16 : 9:
9: 4,608 × 2,592
• O 3 : 2:
2: 4,608 × 3,072
• P 4 : 3:
3: 3,264 × 2,448
• P 16 : 9:
9: 3,264 × 1,840
• O 1 : 1:
1: 3,456 × 3,456
• Q 4 : 3:
3: 2,048 × 1,536
• Q 16 : 9:
9: 1,920 × 1,080
Fujinon 5 × optical zoom lens, F3.9 (wide angle) – F4.9 (telephoto)
f=5.0 mm–25.0 mm (35-mm format equivalent: 28 mm–140 mm)
Up to about 2 × with intelligent digital zoom (up to 10 × when combined with optical zoom)
F3.9/F6.2 (wide angle), F4.9/F8.0 (telephoto)
Approx. 60 cm (1.9 ft.)–infinity (wide angle);
angle); 1.0 m (3.2 ft.)–infinity (telephoto)
• Macro
Macro:: approx. 9 cm–80 cm/3.5 in.–2.6 ft. (wide angle);
angle); 40 cm–80 cm/1.3 ft.–2.6 ft. (telephoto)
Appendix
Specifications
System
Sensitivity
Standard output sensitivity equivalent to ISO 100, 200, 400, 800, 1600, 3200, 6400 (image size
P or Q); AUTO, AUTO (400), AUTO (800), AUTO (1600)
Metering
256-segment throughhrough-tthehe-llens (TTL)
(TTL);; MULTI
Exposure control
Programmed AE
Exposure compensation –2 EV – +2 EV in increments of 1/3 EV
Image stabilization
Optical stabilization (image-sensor shift)
Shutter speed
• AUTO mode:
mode: 1/4 s–
s–11/2,000 s
(combined mechanical and • Other modes:
modes: 4 s–1
s–1/2,000 s
electronic shutter)
Continuous
• P: up to 60 fps; max. 60 frames (Q
(Q 16 : 9 only)
• J: up to 10 fps; max. 9 (O
(O or P) or 18 (Q
(Q) frames
• K: up to 5.0 fps; max. 9 (O
(O or P) or 18 (Q
(Q) frames
• O: up to 3.0 fps; max. 9 (O
(O or P) or 18 (Q
(Q) frames
• M: up to 10 fps max. 18 frames; last 9 (O
(O or P) or 18 (Q
(Q) frames recorded
• N: up to 5.0 fps max. 18 frames; last 9 (O
(O or P) or 18 (Q
(Q) frames recorded
• Q: up to 3.0 fps max. 18 frames; last 9 (O
(O or P) or 18 (Q
(Q) frames recorded
Focus
• Mode
Mode:: Single AF, continuous AF
• Focus-area selection
selection:: CENTER, MULTI, TRACKING
• Autofocus system:
system: Contrast-detect TTL AF
Appendix
115
Specifications
System
White balance
Self-timer
Flash
Flash mode
LCD monitor
Movies
Auto, direct sunlight, shade, daylight fluorescent, warm white fluorescent, cool white
fluorescent, incandescent, underwater
Off, 2 sec., 10 sec., g ((GROUP
GROUP TIMER)
TIMER)
Auto flash; effective range when sensitivity is set to AUTO is approx. 70 cm–3.1 m/2.3 ft.–
10.2 ft. (wide angle)
angle),, 70 cm–2.7 m/2.3 ft.–8.9 ft. (telephoto)
(telephoto);; effective range in macro mode is
approx. 30 cm–80 cm/1.0 ft.–2.6 ft.
Auto, fill flash, off, slow sync (red-eye removal off)
off);; auto with red-eye removal, fill flash with redeye removal, off, slow sync with red-eye removal (red-eye removal on)
3.0-in., 920 k-dot color LCD monitor; frame coverage approx. 100 %
• i 1920×1080
1920×1080:: 1080i, 60 fps
• h 1280×720
1280×720:: 720p, 60 fps
• f 640×480
640×480:: VGA, 30 fps
• k 640×480
640×480:: 120 fps
• k 320×240
320×240:: 240 fps
• k 224×168
224×168:: 360 fps
Input/output terminals
Digital input/output
USB 2.0 High-Speed; MTP/PTP
HDMI output
Micro HDMI connector
116
Appendix
Specifications
Power supply/other
Power supply
NP-50 rechargeable battery
Battery life (approximate
Battery type
Approximate number of frames
number of frames that can
NP-50 (type supplied with camera)
300
be taken with a fully-charged
battery)
CIPA standard, measured in B (auto) mode using battery supplied with camera and SD
memory card.
Charging time
Camera dimensions
(W × H × D)
Shooting weight
Camera weight
Operating conditions
Wireless transmitter
Standards
Operating frequency
Access protocols
Appendix
Note: Number of shots that can be taken with battery varies with battery charge level and will
Note:
decline at low temperatures.
Approx. 180 minutes (+20
(+20 °C/+68 °F)
°F)
116.1 mm × 71.4 mm × 30.3 mm/4.5 in. × 2.8 in. × 1.1 in., excluding projections
Approx. 232 g/8.1 oz., including battery and memory card
Approx. 212 g/7.4 oz., excluding battery, accessories, and memory card
• Temperature
Temperature:: –10 °C – +40 °C/+14 °F – +104 °F
• Humidity
Humidity:: 10% – 80% (no condensation)
IEEE 802.11b/g/n (standard wireless protocol)
• U. S. A., Canada, Taiwan:
Taiwan: 2,412 MHz–2,462 MHz (11 channels)
• Other countries:
countries: 2,412 MHz–2,472 MHz (13 channels)
Infrastructure
117
Specifications
NP-50 rechargeable battery
Nominal voltage
DC 3.6 V
Nominal capacity
1000 mAh
Dimensions (W × H × D) 35.4 mm × 40.0 mm × 6.6 mm/1.3 in. × 1.5 in. × 0.2 in.
Weight
Approx. 18 g/0.6 oz.
AC power adapter
Rated input
Input capacity
Rated output
Operating temperature
Weight
100 V–240 V AC, 50/60 Hz
• 100 VV:: 11.6 VA
5.0 V DC, 1000 mA
0 °C – +40 °C/+32 °F – +104 °F
Approx. 32 g/1.1 oz.
• 240 V:
V: 15.5 VA
Weight and dimensions vary with the country or region of sale.
118
Appendix
Specifications
■ Notices
• Specifications subject to change without notice. FUJIFILM shall not be held liable for
damages resulting from errors in this manual.
• Although the LCD monitor is manufactured using advanced high-precision
technology, small bright points and anomalous colors may appear, particularly in the
vicinity of text. This is normal for this type of LCD monitor and does not indicate a
malfunction; images recorded with the camera are unaffected.
• Digital cameras may malfunction when exposed to strong radio interference (e.g.,
electric fields, static electricity, or line noise).
• Due to the type of lens used, some distortion may occur at the periphery of images.
This is normal.
Appendix
119
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
Restrictions on Camera Settings
The options available in each shooting mode are listed below.
Option
AUTO
N BOFF
N
O
BON
K
L
M
P
h
S/R
g
F
F
H
d
AUTO
N
AUTO (1600)
AUTO (800)
AUTO (400)
6400
3200
1600
800
400
200
100
O
O
P
Q
T
P
c
a
b
f
D
Q B P j k
✔ ✔ ✔
✔ ✔ ✔
✔
✔ ✔ ✔
✔ ✔ ✔
✔
✔ ✔ ✔ ✔1 ✔1
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔
1
✔ ✔1
✔1 ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔ ✔ ✔ ✔ ✔
✔
C D L
✔
✔1
✔
✔
✔
✔1
✔
✔
✔1 ✔
✔ ✔ ✔
✔ ✔ ✔
✔ ✔
✔ ✔ ✔1
Shooting Mode
M Y r N O H
✔
✔
✔
✔
✔
✔ ✔
✔
✔
✔
✔ ✔
✔1 ✔ ✔1 ✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔
✔ ✔
✔
1
1
1
✔ ✔ ✔ ✔ ✔1 ✔1
Q R S F s U V W i F
✔ ✔ ✔ ✔ ✔1
✔ ✔ ✔ ✔ ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔1
✔1 ✔1 ✔1 ✔1
✔1
✔1 ✔ ✔1
✔ ✔ ✔
✔1 ✔1 ✔
✔
✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔ ✔
✔ ✔1 ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Restrictions on Camera Settings
Option
R
P
J
K
O
M
N
Q
ON
b
OFF
F
r
s
x
W i 1920 × 1080
h 1280 × 720
f 640 × 480
k 640 × 480
k 320 × 240
k 244 × 168
F
r
(F)
u
L
l
m
OFF
R
M
B
E
C
Q
✔
✔
✔
✔
✔
✔
✔
✔1
✔1
✔
✔
✔
✔2
✔
✔
✔
✔
B
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
P j k C
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔1 ✔1 ✔1
✔
✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔2
✔ ✔
✔
✔ ✔
✔ ✔
✔
✔
✔
✔2
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
D
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔
L
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
M
✔
✔
✔
✔
✔
✔
✔
Y
✔
✔
✔
✔
✔
✔
✔
✔
✔1 ✔
✔1 ✔1
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔
✔ ✔
✔ ✔2
1 Automatically optimized for selected shooting mode.
2 OFF only.
✔
✔
✔
✔2
✔
✔
✔
✔
Shooting Mode
r N O H
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔
✔1 ✔1 ✔ ✔
✔1 ✔1 ✔1 ✔1
✔
✔
✔
✔2
✔
✔
✔
✔
✔
✔
✔ ✔
✔2 ✔2
✔
✔
✔
✔
✔
✔
✔
✔
Q
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔2
R
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔
✔
S
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔
✔
✔
✔
✔
✔
✔
✔
F
✔
✔
✔
✔
✔
✔
✔
s
✔
✔
✔
✔
✔
✔
✔
✔1 ✔1
✔1 ✔1
✔
✔
✔
✔
✔
✔
✔
✔
U
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔1
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔2
V
✔
✔
✔
✔
✔
✔
✔
W
✔
✔
✔
✔
✔
✔
✔
i F
✔
✔
✔
✔
✔
✔
✔
✔1 ✔1 ✔1
✔1 ✔1 ✔1
✔
✔
✔
✔
✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔2
✔ ✔
✔ ✔
✔2 ✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
Download PDF