Allied Telesis | AT-FH705E | Installation guide | Allied Telesis AT-FH705E Installation guide

AT-FH705E V2
10/100Base Ethernet
Switching Hub
Installation Guide
PN 613-50167-00 Rev A
Copyright  2000 Allied Telesyn International, Corp.
960 Stewart Drive Suite B, Sunnyvale CA USA 94085
All rights reserved. No part of this publication may be
reproduced without prior written permission from Allied
Telesyn International, Corp.
Ethernet is a registered trademark of Xerox Corporation. All
other product names, company names, logos or other
designations mentioned herein are trademarks or registered
trademarks of their respective owners.
Allied Telesyn International, Corp. reserves the right to
make changes in specifications and other information
contained in this document without prior written notice. The
information provided herein is subject to change without
notice. In no event shall Allied Telesyn International, Corp.
be liable for any incidental, special, indirect, or consequential
damages whatsoever, including but not limited to lost profits,
arising out of or related to this manual or the information
contained herein, even if Allied Telesyn International, Corp.
has been advised of, known, or should have known, the
possibility of such damages.
Electrical Safety and Emission
Statement
Standards: This product meets the following standards.
U.S. Federal Communications Commission
DECLARATION OF CONFORMITY
Manufacture Name:
Allied Telesyn International
Manufacture Address:
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA
Manufacture Telephone:
408-730-0950
Declares that the product:
Ethernet switching hub
Model Number:
AT-FH705E
This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device must not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
RADIATED ENERGY
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device pursuant to Part
15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with instructions, may cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on. The user is
encouraged to try to correct the interference by one or more
of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and the
receiver.
iii
-
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician
for help.
Changes and modifications not expressly approved by the
manufacturer or registrant of this equipment can void your
authority to operate this equipment under Federal
Communications Commission rules.
Industry Canada
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
RFI Emission
EN55022 Class B
1
WARNING: In a domestic environment this
product may cause radio interference in which
case the user may be required to take adequate
2
measures.
Immunity
EN50082-1
Electrical Safety
UL 1950 (UL, cUL),
EN60950, VCCI Class B
4
3
Important: Appendix A contains translated safety
statements for installing this equipment. When you see the
, go to Appendix A for the translated safety statement in
your language.
Wichtig: Anhang A enthält übersetzte Sicherheitshinweise
sehen,
für die Installation dieses Geräts. Wenn Sie
schlagen Sie in Anhang A den übersetzten Sicherheitshinweis
in Ihrer Sprache nach.
Vigtigt: Tillæg A indeholder oversatte sikkerhedsadvarsler,
der vedrører installation af dette udstyr. Når De ser symbolet
, skal De slå op i tillæg A og finde de oversatte
sikkerhedsadvarsler i Deres eget sprog.
iv
Belangrijk: Appendix A bevat vertaalde
veiligheidsopmerkingen voor het installeren van deze
ziet, raadpleeg Appendix A
apparatuur. Wanneer u de
voor vertaalde veiligheidsinstructies in uw taal.
Important: L'annexe A contient les instructions de sécurité
relatives à l'installation de cet équipement. Lorsque vous
, reportez-vous à l'annexe A pour
voyez le symbole
consulter la traduction de ces instructions dans votre langue.
Tärkeää: Liite A sisältää tämän laitteen asentamiseen
-symbolin, katso
liittyvät käännetyt turvaohjeet. Kun näet
käännettyä turvaohjetta liitteestä A.
Importante: l’Appendice A contiene avvisi di sicurezza
tradotti per l’installazione di questa apparecchiatura. Il
, indica di consultare l’Appendice A per l’avviso di
simbolo
sicurezza nella propria lingua.
Viktig: Tillegg A inneholder oversatt sikkerhetsinformasjon
, åpner du til
for installering av dette utstyret. Når du ser
Tillegg A for å finne den oversatte sikkerhetsinformasjonen
på ønsket språk.
Importante: O Anexo A contém advertências de segurança
traduzidas para instalar este equipamento. Quando vir o
, leia a advertência de segurança traduzida no seu
símbolo
idioma no Anexo A.
Importante: El Apéndice A contiene mensajes de seguridad
traducidos para la instalación de este equipo. Cuando vea el
, vaya al Apéndice A para ver el mensaje de
símbolo
seguridad traducido a su idioma.
Obs! Bilaga A innehåller översatta säkerhetsmeddelanden
,
avseende installationen av denna utrustning. När du ser
skall du gå till Bilaga A för att läsa det översatta
säkerhetsmeddelandet på ditt språk.
v
Table of Contents
Electrical Safety and Emission
Statement...................................................... iii
Table of Contents ........................................vii
Welcome to Allied Telesyn ........................ ix
Where to Find Web-based Guides ................. ix
Document Conventions .................................. ix
Contacting Allied Telesyn ...............................x
Online Support .........................................x
Telephone or Fax Support ...................... xi
E-mail Support ........................................xii
Returning Products ........................................xii
FTP Server..................................................... xiii
For Sales or Corporate Information ............. xiv
Tell Us What You Think ............................... xiv
AT-FH705E Fast Ethernet Switching
Hub ..................................................................1
Overview ..........................................................1
Features ...........................................................2
Physical Description........................................3
Ports 1 Through 4.....................................3
Port 5 and the Uplink Port ......................4
Front Panel LEDs ....................................5
Power Supply............................................6
vii
Network Topologies .........................................7
Installing the AT-FH705E ..............................9
Verifying the Package Contents ..............9
Selecting a Site ........................................10
Reviewing Safety Guidelines ..................11
Installing the Unit on a Desktop ............13
Installing the Unit on a Wall..................14
Verifying and Troubleshooting the
Installation......................................................16
Warranty Registration ...................................18
Technical Specifications .................................19
Appendix A
Translated Safety and Emission
Information ..................................................21
Appendix B
Technical Support Fax Order ..................35
Incident Summary ..........................................35
Appendix C
AT-FH705E Installation Guide
Feedback .......................................................37
viii
Welcome to Allied Telesyn
This guide contains instructions on how to
install an Allied Telesyn AT-FH705E Ethernet
Switching Hub.
Where to Find Web-based Guides
The Allied Telesyn web site at
www.alliedtelesyn.com provides you with an
easy way to access the most recent
documentation and technical information for all
of our products. All web-based documents for
Allied Telesyn products can be downloaded
from the web site in PDF format.
Document Conventions
This guide uses several conventions that you
should become familiar with before you begin to
install the product.
ix
Note
A note provides additional information.
Caution
A caution indicates that performing or
omitting a specific action may result in
equipment damage or loss of data.
Warning
A warning indicates that performing or
omitting a specific action may result in
bodily injury.
Contacting Allied Telesyn
There are several ways to contact Allied
Telesyn technical support: online, telephone,
fax, and e-mail.
Online Support
You can request technical support online by
filling out the Online Technical Support Form
at www.alliedtelesyn.com/forms/
support.htm.
x
AT-FH705E Installation Guide
Telephone or Fax Support
For technical support via fax, please fill out
the“Technical Support Fax Order” on page 35
and send it to the appropriate location listed
below.
Americas
United States, Canada,
Mexico, Central America,
South America
Tel:
1 (800) 428-4835
Fax:
1 (503) 639-3976
Germany
Germany, Switzerland,
Austria, Eastern Europe
Tel:
(+49) 30-435-900-126
Fax:
(+49) 30-435-70-650
Asia
Singapore, Taiwan, Thailand,
Malaysia, Indonesia, Korea,
Philippines, China,
India, Hong Kong
Tel:
(+65) 3815-612
Fax:
(+65) 3833-830
Italy
Italy, Spain, Portugal, Greece,
Turkey, Israel, Middle East,
Africa
Tel:
(+39) 02-41-30-41
Fax:
(+39) 02-41-30-42-00
Australia
Australia, New Zealand
Tel:
1 (800) 000-880
Fax:
(+61) 2-9438-4966
Japan
Tel:
(+81) 3-3443-5640
Fax:
(+81) 3-3443-2443
United Kingdom
France
France, Belgium, Luxembourg, United Kingdom, Denmark,
Norway, Sweden, Finland,
The Netherlands
Iceland
Tel:
(+33) 1-60-92-15-25
Tel:
(+44) 1-235-442560
Fax:
(+33) 1-69-28-37-49
Fax:
(+44) 1-235-442680
xi
E-mail Support
United States and Canada
TS1@alliedtelesyn.com
Latin America, Mexico, Puerto Rico,
Caribbean, and Virgin Islands
latin_america@alliedtelesyn.com
United Kingdom, Sweden, Norway,
Denmark, and Finland
support_europe@alliedtelesyn.com
Returning Products
Products for return or repair must first be
assigned a Return Materials Authorization
(RMA) number. A product sent to Allied
Telesyn without a RMA number will be
returned to the sender at the sender’s expense.
To obtain an RMA number, contact Allied
Telesyn’s Technical Support at one of the
following locations:
North America
2124 Zanker Road
San Jose, CA 95131
Tel: 1-800-428-4835,
option 4
Fax: 1-503-639-3716
xii
European Customer
Support Centre
10/11 Bridgemead Close
Westmead Industrial Estate
Swindon, Wiltshire SN5 7YT
England
Tel: +44-1793-501401
Fax: +44-1793-431099
AT-FH705E Installation Guide
Latin America, the
Caribbean,
Virgin Islands
Tel: international code +
425-481-3852
Fax: international code +
425-483-9458
Mexico and Puerto Rico
Tel: 1-800-424-5012, ext 3852
or
1-800-424-4284, ext 385 2
Mexico only:
95-800-424-5012, ext 3852
Fax: international code +
425-489-9191
FTP Server
If you need a device driver for an Allied Telesyn
device and you know the name of the driver,
you can download the software by connecting
directly to our FTP server at
ftp://gateway.centre.com.
At login, enter ‘anonymous’. Enter your e-mail
address for the password as requested by the
server at login.
xiii
For Sales or Corporate Information
For sales or corporate information contact
Allied Telesyn at one of the following locations:
Allied Telesyn
International, Corp.
19800 North Creek Parkway,
Suite 200
Bothell, WA 98011
Tel: 1 (425) 487-8880
Fax: 1 (425) 489-9191
Allied Telesyn
International, Corp.
960 Stewart Drive, Suite B
Sunnyvale, CA 94086
Tel: 1 (800) 424-4284 (USA
and Canada )
Fax: 1 (408) 736-0100
Tell Us What You Think
If you have any comments or suggestions on
how we might improve this or other Allied
Telesyn documents, please fill out the “ATFH705E Installation Guide Feedback” on page
37 and return the form to us at the address or
fax number provided. You can also provide
feedback online by filling out the Send Us
Feedback Form at www.alliedtelesyn.com/
forms/feedback.htm.
xiv
AT-FH705E Fast Ethernet
Switching Hub
Overview
The AT-FH705E is a 10Base-T/100Base-TX
unmanaged switching hub. The device provides
you with a simple, cost-effective solution for
Ethernet connectivity between end nodes
operating at either 10 or 100 Mbps.
100M
7.5V@1A
Link/Act
FH705E
V2
/100
5 Port 10g Hub
Switchin
Fdx/Hdx
Pwr
1
2
3
4
5
Figure 1 AT-FH705E Ethernet Switching Hub
1
Features
The AT-FH705E Switching Hub has the
following features:
❑ Five auto-negotiating 10/100 Mbps
twisted pair ports with RJ-45 connectors
❑ One Uplink port for connecting the ATFH705E Switching Hub to another switch
or hub without a crossover cable
❑ IEEE 802.3 and IEEE 802.3u compliant
❑ External power adapter
❑ Desktop or wall-mount installation
Figure 2 and Figure 3 show the front and back
panels of the hub.
100M
FH705E
7.5V@1A
Link/Act
V2
5 Port 10/100
Switching Hub
Pwr
Fdx/Hdx
1
2
3
4
Port LEDs
5
DC Power Connector
Figure 2 Front Panel
2
AT-FH705E Installation Guide
Uplink
5
4
3
2
1
Figure 3 Back Panel
Physical Description
The physical description of the device includes:
❑ Ports 1 through 4
❑ Port 5 and the Uplink port
❑ LEDs
❑ Power supply
Ports 1 Through 4
Ports 1 through 4 can operate at either 10 Mbps
or 100 speed and in either full- or half-duplex
mode. The ports, featuring RJ-45 connectors,
are configured as MDI-X, meaning that you can
connect a workstation or server to one of the
ports without using a crossover cable. The ports
have a maximum operating distance of 100
meters (328 feet) using category 5 cable.
3
The ports are IEEE802.3u Auto-Negotiation
compliant. This means that the ports can
automatically configure their speed and duplex
mode to match the capabilities of the end nodes
connected to the ports.
Port 5 and the Uplink Port
Port 5 and the Uplink port allow you to connect
an additional workstation to the hub or
interconnect the switching hub with another
switch or hub, without the use of a cross-over
cable. If you need to connect an additional
workstation to the device, use Port 5, which is
configured as MDI-X, just like ports 1 through
4. If you need to connect the device to a switch
or another hub, use the Uplink port, which is
configured as MDI.
Both Port 5 and the Uplink port offer 10 Mbps
or 100 Mbps performance and auto-negotiation
operation for both speed and duplex mode, just
like ports 1 through 4. Both ports feature an
RJ-45 connector and have a maximum
operating distance of 100 meters (328 feet)
using category 5 cable.
Note
You can use either port 5 or the Uplink
port. You cannot use both
simultaneously.
4
AT-FH705E Installation Guide
Front Panel LEDs
Refer to Table 1 for a description of the device
LEDs.
Table 1 LED Functions
LEDs
Color
Description
Power
Green
On means there is power to
the hub.
Off means there is no power
to the hub.
100M
Green
On means the port speed is
100 Mbps.
Off means the port speed is
10 Mbps.
Link/Act
Green
On indicates a valid physical
link on the port.
Flashing indicates data is
being transmitted or received
on the port.
Off means there is no link on
the port.
5
Table 1 LED Functions (continued)
LEDs
Color
Description
Fdx/Hdx
Green
On indicates the port is
operating in full-duplex
mode.
Off indicates the port is
operating in half-duplex
mode.
Power Supply
The AT-FH705E uses an external power
adapter that comes standard with the hub.
6
AT-FH705E Installation Guide
Network Topologies
Figure 4 illustrates a network that consists of
one AT-FH705E Ethernet Switching Hub used
to interconnect four workstations and a server.
In this configuration, the Uplink port is not
used.
Uplink
5
4
3
2
1
Figure 4 Single AT-FH705E Switching Hub Topology
7
Figure 5 illustrates a network of two ATFH705E Ethernet Switching Hubs that have
been interconnected using the Uplink ports on
the two units. Using the Uplink ports
eliminates the need for a cross-over cable to
interconnect the hubs.
Uplink
Uplink
5
4
3
2
5
4
3
2
1
1
Figure 5 Multiple AT-FH705E Ethernet Switching Hub
Topology
8
AT-FH705E Installation Guide
Installing the AT-FH705E
This section contains the procedures for
installing the device.
Verifying the Package Contents
Make sure that the package includes the
following items. If any of the items are
damaged or missing, contact your Allied
Telesyn representative immediately.
❑ One AT-FH705E Switching Hub
❑ One power adapter
❑ Four self-adhesive rubber feet
❑ Warranty card
❑ This installation guide
Note
For wall-mount installation, you must
supply the two screws and plastic
anchors or other material necessary to
physically mount the device on the wall.
9
Selecting a Site
Make sure you observe the following site
requirements:
❑ Make sure you are placing the device in a
dust-free and moisture-free environment.
❑ Do not block the ventilation openings on
the unit. Allow at least 10 centimeters (4
inches) of space at the front and back of
the unit for ventilation.
❑ Make sure that the device’s power is
accessible and cables can be connected
easily.
❑ Cabling should be away from sources of
electrical noise such as radios,
transmitters, broadband amplifiers,
power lines, and fluorescent fixtures.
❑ Do not place objects on top of the device.
❑ Use dedicated power circuits or power
conditioners to supply power to the device.
10
AT-FH705E Installation Guide
❑ Observe the following cabling
specifications:
Ports
Connector
Type
Type of
Cable
Maximum
Distance
1 through 5
RJ-45
Category 5
100 m
(328 ft)
Uplink
RJ-45
Category 5
100 m
(328 ft)
Reviewing Safety Guidelines
Please review the following safety guidelines
before you begin to install the device.
Warning
Power cord is used as a
disconnection device: To deenergize equipment, disconnect the
power cord.
5
Caution
Power to the hub must be sourced only
from the adapter.
6
11
Caution
EUROPE - EU: Use TÜV licensed AC
adapter of DC 7.5V, 1A.
7
Caution
USA/CANADA: Use a UL Listed/CSA
Certified AC adapter of DC 7.5V, 1A.
7
Caution
Australia: Use a Australian Safety
Approved AC adapter of DC 7.5V 1A.
7
Caution
Air vents: The air vents must not be
blocked on the unit and must have free
access to the room ambient air for cooling.
8
Caution
Operating Temperature: This product
is designed for a maximum ambient
temperature of 40°C.
9
Caution
All Countries: Install this product in
accordance with local and National
Electric Codes.
10
12
AT-FH705E Installation Guide
Installing the Unit on a Desktop
To install the device on a desktop, perform the
following procedure. To mount the unit on a
wall, perform the steps “Installing the Unit on a
Wall” on page 14.
1. Attach the four self-adhesive rubber feet to
the bottom of the device, positioning them in
the indentations.
2. Place the device on a flat, level surface.
3. Plug the power adapter into the power
receptacle, then plug the DC power cord into
the DC connector on the front panel of the
device.
Warning
The power cord is used as a
disconnection device. To de-energize
equipment, disconnect the power cord.
5
4. Make sure the Power LED on the front panel
lights green.
13
5. Attach the data cables to the switching hub
ports. Do not use a cross-over cable to connect
workstations or servers to ports 1 through 5.
Do not use a cross-over cable to connect
another switch or hub to the Uplink port.
Note
You can use either port 5 or the Uplink
port on an AT-FH705E Switching Hub,
but you cannot use both simultaneously.
6. Go to the procedure “Verifying and
Troubleshooting the Installation” on page 16.
Installing the Unit on a Wall
For wall-mount installation, you can position
the device vertically or horizontally on the wall
using the keyhole cutouts in the bottom of the
hub chassis.
1. If previously attached, remove the rubber feet
and all cables and the DC power cord from the
device.
2. Select a wall location for the device.
14
AT-FH705E Installation Guide
Note
For wall-mount installation, you must
supply the two screws and plastic
anchors or other material necessary to
physically mount the device on the wall.
3. Install two plastic anchors and two pan-head
screws into the wall, separated by 5
centimeters (approximately 2 inches).
4. Position the device onto the wall screws.
5. Plug the power adapter into the power
receptacle, then plug the DC power cord into
the DC connector on the front panel of the
switching hub.
Warning
The power cord is used as a
disconnection device. To de-energize
equipment, disconnect the power cord.
5
6. Connect the data cables to the ports on the
switching hub.
15
7. Attach the data cables to the AT-FH705E
ports. Do not use a cross-over cable to connect
workstations or servers to ports 1 through 5.
Do not use a cross-over cable to connect
another AT-FH705E to the Uplink port.
Note
You can use either port 5 or the Uplink
port, but you cannot use both
simultaneously.
8. Go to the procedure “Verifying and
Troubleshooting the Installation” on page 16.
Verifying and Troubleshooting the
Installation
The following procedure should be perform
after you have initially installed the unit to
check to be sure that the device is operating
properly. You can also perform this procedure
to troubleshoot the unit in the event you
experience any problems with the device.
1. Check the Power LED. The LED should be
ON. If the Power LED is OFF, check the
following:
❑ Check to be sure that the power adapter is
securely connected to the power source
and to the DC connector on the front of the
16
AT-FH705E Installation Guide
AT-FH705E Switching Hub.
❑ Check to be sure that the power outlet has
power by connecting another device to it.
❑ Try replacing the power adapter with
another power adapter.
2. Check the Link/Act LED for each port. The
LED should be lit steady or flashing. If a
Link/Act LED is OFF, check the following:
❑ Check to be sure that the node connected
to the port on the AT-FH705E is powered
ON. If the node is OFF, power the unit
ON.
❑ Check to be sure that the distance
between the hub and the connected
network device is no greater than 100
meters (328 feet).
❑ Check to be sure that you are using
Category 5 cable.
❑ Check to be sure that the cable has not
been cut or damaged.
17
3. If the Lnk/Act LED for a port is on but there
is a communication problem to the end node
connected to the port, such as the loss of data,
check the following:
❑ Check to be sure that the distance
between the AT-FH705E and the
connected network device is no greater
than 100 meters (328 feet).
❑ Check to be sure that you are using
Category 5 cable.
Warranty Registration
When you have finished installing the unit, you
should register your product by completing the
enclosed warranty card and sending it in, or by
visiting our web site at
www.alliedtelesyn.com/forms/
warranty.htm and completing the on-line
registration form.
18
AT-FH705E Installation Guide
Technical Specifications
Standards Compatibility:
IEEE 802.3,
IEEE802.3u
Interfaces:
RJ-45 connectors
Physical Dimensions:
WxDxH
100 x 78.5 x 26 mm
(3.93 x 3.09 x 1.02
in.)
Power Supply:
Output: 7.5V @ 1A
Power Consumption:
4W
Environment Specifications:
Operating Temperature 0° to 40° C
Storage Temperature
-25° to 70° C
Operating Humidity
10% to 90%
Relative Humidity
Storage Humidity
10% to 95%
Relative Humidity
Electromagnetic Emission: FCC Class B;
CE Class B;
VCCI Class B
19
Appendix A
Translated Safety and
Emission Information
Important: This appendix contains multiplelanguage translations for the safety statements
in this guide.
Wichtig: Dieser Anhang enthält
Übersetzungen der in diesem Handbuch
enthaltenen Sicherheitshinweise in mehreren
Sprachen.
Vigtigt: Dette tillæg indeholder oversættelser i
flere sprog af sikkerhedsadvarslerne i denne
håndbog.
Belangrijk: Deze appendix bevat vertalingen
in meerdere talen van de
veiligheidsopmerkingen in deze gids.
Important: Cette annexe contient la traduction
en plusieurs langues des instructions de
sécurité figurant dans ce guide.
Tärkeää: Tämä liite sisältää tässä oppaassa
esiintyvät turvaohjeet usealla kielellä.
21
Importante: questa appendice contiene
traduzioni in più lingue degli avvisi di sicurezza
di questa guida.
Viktig: Dette tillegget inneholder oversettelser
til flere språk av sikkerhetsinformasjonen i
denne veiledningen.
Importante: Este anexo contém traduções em
vários idiomas das advertências de segurança
neste guia.
Importante: Este apéndice contiene
traducciones en múltiples idiomas de los
mensajes de seguridad incluidos en esta guía.
Obs! Denna bilaga innehåller flerspråkiga
översättningar av säkerhetsmeddelandena i
denna handledning.
22
AT-FH705E Installation Guide
Standards: This product meets the following standards:
U.S. Federal Communications Commission
DECLARATION OF CONFORMITY
Manufacture Name:
Allied Telesyn International
Manufacture Address:
950 Stewart Drive, Suite B
Sunnyvale, CA 94085 USA
408-730-0950
Manufacture Telephone:
Declares that the product:
Ethernet switching hub
Model Number:
AT-FH705E
This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device must not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
RADIATED ENERGY
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device pursuant to Part
15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with instructions, may cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on. The user is
encouraged to try to correct the interference by one or more
of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and the
receiver.
-
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician
for help.
23
Changes and modifications not expressly approved by the
manufacturer or registrant of this equipment can void your
authority to operate this equipment under Federal
Communications Commission rules.
Industry Canada
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
1
RFI Emissions
2
WARNING: In a domestic environment this
product may cause radio interference in which
case the user may be required to take adequate
measures.
3
Immunity
EN50082-1 1997
4
Electrical Safety
UL 1950 (UL, cUL),
EN60950,
VCCI Class B
5
CAUTION: POWER CORD IS USED AS A
DISCONNECTION DEVICE. TO DE-ENERGIZE
EQUIPMENT, disconnect the power cord.
6
Power to the hub must be sourced only from the
adapter.
7
USA/CANADA: Use a UL Listed/CSA Certified
AC adapter of DC 7.5V, 1A.
EN55022 Class B
SAFETY
EUROPE - EU: Use TÜV licensed AC adapter of
DC 7.5V, 1A.
24
Australia: Use a Australian Safety Approved AC
adapter of DC 7.5V, 1A.
8
CAUTION: Air vents must not be blocked and
must have free access to the room ambient air for
cooling.
AT-FH705E Installation Guide
9
OPERATING TEMPERATURE: This product is
designed for a maximum ambient temperature of
40° degrees C.
10
ALL COUNTRIES: Install product in accordance
with local and National Electrical Codes.
Normen: Dieses Produkt erfüllt die
Anforderungen der nachfolgenden Normen.
1
Hochfrequenzstörung
2
WARNUNG: Bei Verwendung zu Hause kann
dieses Produkt Funkstörungen hervorrufen. In
diesem Fall müßte der Anwender angemessene
Gegenmaßnahmen ergreifen.
3
Störsicherheit
EN50082-1 1997
4
Elektrische Sicherheit
UL 1950 (UL, cUL),
EN60950,
VCCI Class B
EN55022 Klasse B
SICHERHEIT
5
VORSICHT: DAS NETZKABEL DIENT ZUM
TRENNEN DER STROMVERSORGUNG. ZUR
TRENNUNG VOM NETZ, KABEL AUS DER
STECKDOSE ZIEHEN.
6
Der Buchse darf nur aus dem Adapter Strom
zugeführt werden.
7
Gebrauchen Sie einen von TÜV zugelassenen
Wechselstromadapter für Gleichstrom 7,5 V, 1A.
8
VORSICHT
Die Entlüftungsöffnungen dürfen nicht versperrt
sein und müssen zum Kühlen freien Zugang zur
Raumluft haben.
9
BETRIEBSTEMPERATUR: Dieses Produkt
wurde für den Betrieb in einer
Umgebungstemperatur von nicht mehr als 40° C
entworfen.
10
ALLE LÄNDER: Installation muß örtlichen und
nationalen elektrischen Vorschriften entsprechen.
25
26
Standarder: Dette produkt tilfredsstiller de
følgende standarder.
1
Radiofrekvens forstyrrelsesemission: EN55022
Klasse B
2
ADVARSEL: I et hjemligt miljø kunne dette
produkt forårsage radio forstyrrelse. Bliver det
tilfældet, påkræves brugeren muligvis at tage
tilstrækkelige foranstaltninger.
3
Immunitet
EN50082-1 1997
4
Elektrisk sikkerhed
UL 1950 (UL, cUL),
EN60950,
VCCI Class B
SIKKERHED
5
ADVARSEL: DEN STRØMFØRENDE
LEDNING BRUGES TIL AT AFBRYDE
STRØMMEN. SKAL STRØMMEN TIL
APPARATET AFBRYDES, tages ledningen ud af
stikket.
6
Strømforsyningen til apparatet må udelukkende
tages fra tilpasningstransformatoren.
7
Brug kun TÜV godkendt
vekselstrømstransformator på 7.5 V jævnstrøm,
1A.
8
ADVARSEL: Ventilationsåbninger må ikke
blokeres og skal have fri adgang til den omgivende
luft i rummet for afkøling.
9
BETJENINGSTEMPERATUR: Dette apparat
er konstrueret til en omgivende temperatur på
maksimum 40 grader C.
10
ALLE LANDE: Installation af produktet skal ske
i overensstemmelse med lokal og national
lovgivning for elektriske installationer.
AT-FH705E Installation Guide
Eisen: Dit product voldoet aan de volgende eisen.
1
RFI Emissie
2
WAARSCHUWING: Binnenshuis kan dit
product radiostoring veroorzaken, in welk geval
de gebruiker verplicht kan worden om gepaste
maatregelen te nemen.
3
Immuniteit
4
Electrische Veiligheid
EN55022 Klasse B
EN50082-1 1997
UL 1950 (UL, cUL),
EN60950,
VCCI Class B
VEILIGHEID
5
WAARSCHUWING: HET TOESTEL WORDT
UITGESCHAKELD DOOR DE STROOMKABEL
TE ONTKOPPELEN.OM HET TOESTEL
STROOMLOOS TE MAKEN: de stroomkabel
ontkoppelen.
6
Stroom mag alleen via de adapter naar het
apparaat toegevoerd worden.
7
Gebruik een door TÜV gekeurde
wisselstroomadapter van 7,5 Volt gelijkstroom, 1
ampères.
8
OPGELET: De ventilatiegaten mogen niet
worden gesperd en moeten de omgevingslucht
ongehinderd toelaten voor afkoeling.
9
BEDRIJFSTEMPERATUUR: De
omgevingstemperatuur voor dit produkt mag niet
meer bedragen dan 40 graden Celsius.
10
ALLE LANDEN: het toestel installeren
overeenkomstig de lokale en nationale elektrische
voorschriften.
27
28
Normes: ce produit est conforme aux normes de
suivantes.
1
Emission d’interférences
radioélectriques
EN55022 Classe B
2
MISE EN GARDE : dans un environnement
domestique, ce produit peut provoquer des
interférences radioélectriques. Auquel cas,
l’utilisateur devra prendre les mesures adéquates.
3
Immunité
EN50082 - 1 1997
4
Sécurité électrique
UL 1950 (UL, cUL),
EN60950,
VCCI Class B
5
DANGER DE FOUDRE
DANGER: NE PAS MANIER le matériel ou les
CÂBLES lors d’activité orageuse.
6
L’alimentation du concentrateur doit être
uniquement fournie par l’adaptateur.
7
Utiliser un adaptateur secteur conforme TÜV de
7,5 V, 1 A en courant continu.
8
ATTENTION: Ne pas bloquer les fentes
d’aération, ceci empêcherait l’air ambiant de
circuler librement pour le refroidissement.
9
TEMPÉRATURE DE FONCTIONNEMENT:
Ce matériel est capable de tolérer une
température ambiante maximum de ou 40 degrés
Celsius.
10
POUR TOUS PAYS: Installer le matériel
conformément aux normes électriques nationales
et locales.
AT-FH705E Installation Guide
Standardit: Tämä tuote on seuraavien
standardien mukainen.
1
Radioaaltojen häirintä
2
VAROITUS: Kotiolosuhteissa tämä laite voi
aiheuttaa radioaaltojen häiröitä, missä
tapauksessa laitteen käyttäjän on mahdollisesti
ryhdyttävä tarpeellisiin toimenpiteisiin.
3
Kestävyys
EN50082-1 1997
4
Sähköturvallisuus
UL 1950 (UL, cUL),
EN60950,
VCCI Class B
EN55022 Luokka B
TURVALLISUUS
5
HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN
VIRRANKATKAISULAITTEENA. VIRTA
KATKAISTAAN irrottamalla virtajohto.
6
Tähtipisteeseen (hub) syötettävän virran pitää
tulla ainoastaan sovittimesta.
7
Käytä TÜV-lisenssillä valmistettua
verkkosovitinta, jonka tasajännitteen
nimellisarvot ovat DC 7,5 V, 1 A.
8
HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia
ja niillä täytyy olla vapaa yhteys ympäröivään
huoneilmaan, jotta ilmanvaihto tapahtuisi.
9
KÄYTTÖLÄMPÖTILA: Tämä tuote on
suunniteltu ympäröivän ilman
maksimilämpötilalle 40°C.
10
KAIKKI MAAT: Asenna tuote paikallisten ja
kansallisten sähköturvallisuusmääräysten
mukaisesti.
29
30
Standard: Questo prodotto è conforme ai
seguenti standard.
1
Emissione RFI (interferenza di
radiofrequenza)
EN55022 Classe B
2
AVVERTENZA: in ambiente domestico questo
prodotto potrebbe causare radio interferenza. In
questo caso potrebbe richiedersi all’utente di
prendere gli adeguati provvedimenti.
3
Immunità
EN50082-1 1997
4
Sicurezza elettrica
UL 1950 (UL, cUL),
EN60950,
VCCI Class B
NORME DI SICUREZZA
5
ATTENZIONE: IL CAVO DI ALIMENTAZIONE
È USATO COME DISPOSITIVO DI
DISATTIVAZIONE. PER TOGLIERE LA
CORRENTE AL DISPOSITIVO staccare il cavo di
alimentazione.
6
Questo dispositivo deve essere alimentato solo
mediante l’adattatore.
7
Utilizzare l’adattatore per c.a. da 7,5 V c.c. e 1 A
conforme alla normativa TÜV.
8
ATTENZIONE: le prese d’aria non vanno
ostruite e devono consentire il libero ricircolo
dell’aria ambiente per il raffreddamento.
9
TEMPERATURA DI FUNZIONAMENTO:
Questo prodotto è concepito per una temperatura
ambientale massima di 40 gradi centigradi.
10
TUTTI I PAESI: installare il prodotto in
conformità delle vigenti normative elettriche
nazionali.
AT-FH705E Installation Guide
Sikkerhetsnormer: Dette produktet
tilfredsstiller følgende sikkerhetsnormer.
1
RFI stråling
2
ADVARSEL: Hvis dette produktet benyttes til
privat bruk, kan produktet forårsake
radioforstyrrelse. Hvis dette skjer, må brukeren
ta de nødvendige forholdsregler.
3
Immunitet
EN50082-1 1997
4
Elektrisk sikkerhet
UL 1950 (UL, cUL),
EN60950,
VCCI Class B
EN55022 Klasse B
SIKKERHET
5
FORSIKTIG: STRØMLEDNINGEN BRUKES
TIL Å FRAKOBLE UTSTYRET. FOR Å
DEAKTIVISERE UTSTYRET, må
strømforsyningen kobles fra.
6
All strømtilførsel må komme fra adapteren.
7
Benytt TÜV-godkjent AC-adapter på 7,5V DC, 1A.
8
FORSIKTIG: Lufteventilene må ikke blokkeres,
og må ha fri tilgang til luft med romtemperatur
for avkjøling.
9
DRIFTSTEMPERATUR: Dette produktet er
konstruert for bruk i maksimum romtemperatur
på 40 grader celsius.
10
ALLE LAND: Produktet må installeres i samsvar
med de lokale og nasjonale elektriske koder.
31
32
Padrões: Este produto atende aos seguintes
padrões.
1
Emissão de interferência de
radiofrequência
EN55022 Classe B
2
AVISO: Num ambiente doméstico este produto
pode causar interferência na radiorrecepção e,
neste caso, pode ser necessário que o utente tome
as medidas adequadas.
3
Imunidade
EN50082-1 1997
4
Segurança Eléctrica
UL 1950 (UL, cUL),
EN60950,
VCCI Class B
SEGURANÇA
5
CUIDADO: O CABO DE ALIMENTAÇÃO É
UTILIZADO COMO UM DISPOSITIVO DE
DESCONEXÃO. PARA DESELETRIFICAR O
EQUIPAMENTO, desconecte o cabo de
ALIMENTAÇÃO.
6
Use somente o adaptador fornecido para
alimentação elétrica do hub.
7
Use um adaptador de corrente alternada com
saída DC de 7,5V e 1A em conformidade com as
especificações da TÜV.
8
CUIDADO: As aberturas de ventilação não
devem ser bloqueadas e devem ter acesso livre ao
ar ambiente para arrefecimento adequado do
aparelho.
9
TEMPERATURA DE FUNCIONAMENTO:
Este produto foi projetado para uma temperatura
ambiente máxima de 40 graus centígrados.
10
TODOS OS PAÍSES: Instale o produto de acordo
com as normas nacionais e locais para instalações
elétricas.
AT-FH705E Installation Guide
Estándares: Este producto cumple con los
siguientes estándares.
1
Emisión RFI
2
ADVERTENCIA: en un entorno doméstico, este
producto puede causar radiointerferencias, en
cuyo caso, puede requerirse del usuario que tome
las medidas que sean convenientes al respecto.
3
Inmunidad
EN50082-1 1997
4
Seguridad eléctrica
UL 1950 (UL, cUL),
EN60950,
VCCI Class B
EN55022 Clase B
SEGURIDAD
5
ATENCION: EL CABLE DE ALIMENTACION
SE USA COMO UN DISPOSITIVO DE
DESCONEXION. PARA DESACTIVAR EL
EQUIPO, desconecte el cable de alimentación.
6
La energía para el dispositivo central o "hub" debe
provenir únicamente del adaptador.
7
Utilizar un adaptador de corriente alterna
autorizado TÜV de 7,5 voltios de corriente
continua y 1 amperios.
8
ATENCION: Las aberturas para ventilación no
deberán bloquearse y deberán tener acceso libre al
aire ambiental de la sala para su enfriamiento.
9
TEMPERATURA REQUERIDA PARA LA
OPERACIÓN: Este producto está diseñado para
una temperatura ambiental máxima de 40 grados
C.
10
PARA TODOS LOS PAÍSES: Monte el producto
de acuerdo con los Códigos Eléctricos locales y
nacionales.
33
Standarder: Denna produkt uppfyller följande
standarder.
1
Radiostörning
2
VARNING: Denna produkt kan ge upphov till
radiostörningar i hemmet, vilket kan tvinga
användaren till att vidtaga erforderliga åtgärder.
3
Immunitet
EN50082-1 1997
4
Elsäkerhet
UL 1950 (UL, cUL),
EN60950,
VCCI Class B
34
EN55022 Klass B
SÄKERHET
5
VARNING: NÄTKABELN ANVÄNDS SOM
STRÖMBRYTARE FÖR ATT KOPPLA FRÅN
STRÖMMEN, dra ur nätkabeln.
6
Endast anslutningsenheten får vara kraftkälla till
centralen.
7
Använd en växelströmsanslutningsenhet
licensierad av TÜV.Likström 7,5V, 1A.
8
VARNING: Luftventilerna får ej blockeras och
måste ha fri tillgång till omgivande rumsluft för
avsvalning.
9
DRIFTSTEMPERATUR: Denna produkt är
konstruerad för rumstemperatur ej överstigande
40 grader Celsius.
10
ALLA LÄNDER: Installera produkten i enlighet
med lokala och statliga bestämmelser för
elektrisk utrustning.
Appendix B
Technical Support Fax Order
Name __________________________________
Company _______________________________
Address ________________________________
City____________________________________
State/Province __________________________
Zip/Postal Code ________________________
Country ________________________________
Phone __________________________________
Fax ___________________________________
Incident Summary
Model number of Allied Telesyn product
I am using______________________________
Firmware release number of Allied Telesyn
product ________________________________
Other network software products I am using
(e.g., network managers) ________________
_______________________________________
35
Brief summary of problem _______________
_______________________________________
Conditions (List the steps that led up
to the problem. _________________________
_______________________________________
_______________________________________
Detailed description (Please use separate sheet)
Please also fax printouts of relevant files such as
batch files and configuration files. When
completed, fax this sheet to the appropriate
Allied Telesyn office. Fax numbers can be found
on page viii.
36
Appendix C
AT-FH705E Installation Guide
Feedback
Please tell us what additional information you
would like to see discussed in this guide. You
can fax or mail this form to the mailing address
and fax number at the bottom of the page.
I found the following the most valuable _______
___________________________________________
___________________________________________
I would like the following more developed _____
___________________________________________
___________________________________________
I would find this guide more useful if _________
___________________________________________
___________________________________________
Allied Telesyn International, Corp.
c/o Technical Communications
960 Stewart Drive, Suite B
Sunnyvale, CA 94085 USA
PN 613-50167-00 Rev A
37
Download PDF