Avanti Manager's User Guide

Avanti Manager's User Guide
Avanti™
On board PA
Simultaneously depressing key’s 4 and 8 will
activate a PA thus creating a full alarm
condition. This feature can be used when the
system is in DAY mode or SET . (If you have
an RS Panel fitted with a communicator then
a signal will also be sent.)
Additionally RS Panels have individual
duress codes for the Users, Holiday and
Manager. Duress is only accessible in SET .
Entering an access code followed by the first
digit within 1 to 1.5 seconds will activate a
silent PA. i.e.: - 0 1 2 3 0
Quick Set
This feature allows the panel to be SET so
that it overrides the programmed exit time.
Entering an access code, selecting Program
A / B or * and then pressing ¯will cause the
panel to SET within 2 seconds.
Holiday Access Code
The purpose of this code is to allow access
to the property whilst the manager is absent.
The Holiday Access Code is programmed by
the Manager and is only valid until the
Manager UNSETS the system. At this point
the Holiday Access Code becomes invalid
and is no longer accepted by the control
panel.
Fault during setting
If the system is unable to SET then the
internal sounders will make an error tone.
The fault on the system will be indicated by
the relevant zone/PA/Tamper LED being lit. If
a zone LED is lit then ensure that all windows
and doors are closed and the zone is clear. If
the fault persists then it may be possible to
omit the zone. It is advisable to contact your
engineer for further information.
Alarm Activation
If the system has been activated then an
access code needs to be entered. To reset
the system all that is required is to re-enter
an access code.
Call Engineer
The panel may have been programmed to
display that the system may require a
service. If the Tamper LED flashes then you
should contact your engineer. If the Tamper
LED is flashing this does not affect the
operation of the system.
(NB if you have an RS panel then the
Tamper LED flashing could indicate that you
have a line fail and you should contact your
engineer.)
&
Fi
re
Lt
d
User Codes
A User can perform the same operations as
a Manager except they are unable to View
the Event Log, access the Test Menu or
change Access Codes. If a User does not
select a program when setting the panel then
the system will default to Full Set. (NB a
Manager must select a program.)
Chime
From DAY mode chime may be changed in
the following way: Press ¯. All of the zones
that chime when they are activated will have
their LED lit. Press the key that represents
the zone that you require. When the LED is
lit, that zone will chime upon activation.
Press A To Accept / Press B To Abort the
changes .
After selecting, press the zone buttons you
wish to omit
1 2
3
4
5
6
7
8
Select Program A/B or *
ur
ity
To omit a Zone
type Z
ec
Avanti ™
Manager Operating guide
?
?
en
llig
?
2 User access code 2
3 User access code 3
2
4 User access code 4
5 Holiday code
6 Manager code
In
?
1 User access code 1
te
Enter Manager Code
tS
within 5 Secs
Manager menu
Set Program * Full
*
Set Program A
Set Program B
Set Access Codes
View Event Log
Enter Test Menu
Exit to Day Mode
A
B
1
2
9
Z
Avanti and mdt are trademarks of mdt ltd
Z Manager menu
Enter 4 new digits
?
?
?
?
Delete access code
Z
Z
Z
Z
A To accept
B To abort
Z Return to Day mode
Test Menu
3 Switch speakers on
0 Switch outputs off
1 Switch bell on
2 Switch strobe on
2
6 Enter walk test
9 Zone status
Z Exit walk test
After selecting Event Log
the zone, PA and Tamper LED’s will
show the latest event
A flashing LED indicates the zone that
was first activated.
Any other LED lit was activated after
the first event but before system unset
1 2 3 4 5 6 7 8
Day
PA
Tamper
To navigate through the log
1 Jump to oldest event
2
2 Move one event older
3 Move one event newer
4 Jump to newest event
Z Manager menu
Maximum of 16 events can be viewed
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement