Cables to Go | 10/100Base-TX | DeltaV Control Network Hardware

DeltaV Distributed Control System
Product Data Sheet
October 2014
DeltaV™ Control Network Hardware
The DeltaV™ Control Network is easy to install and maintain with the new DeltaV Smart Switches
„„Easy to use
„„Scalable and cost-effective
„„Built-in network diagnostics
„„Fully Redundant Network
Introduction
Your control network is the backbone of your system. The
DeltaV™ Control Network (DCN) is a standard Ethernet network
dedicated to the DeltaV system. You connect the DeltaV
workstations and the controllers using the Control Network.
The Control Network is a dual speed 10/100BaseT network.
CAT 5 screened (ScTP) twisted-pair cable connects each node
to the hub or switch.
The DeltaV Control Network is an easy to design and
implement dedicated Ethernet network. All DeltaV devices
are connected to the same subnet and all of the network
addressing (IP addresses) for DeltaV equipment is managed
by the DeltaV system. The DeltaV “self-managed network”
does not require the user to track network address usage.
The DeltaV system supports a specific set of network switches
for the DeltaV Control Network and the DeltaV Smart Switches
(see the ordering information included in this document for
details of the specific control network devices we support
and the DeltaV Smart Switches).
Benefits
Easy to design and implement. As a dedicated network
with predictable communications traffic DeltaV has done all
of the system testing so you only have to plug the components
together to create the control network.
DeltaV Control Network Hardware
Plug-and-play components. You can expand the network
easily: just plug in another workstation or controller and it is
recognized by the system.
Standards compliance. Network components are compliant
with standards such as IEEE, CE and CSA.
Network diagnostics. On the Smart Switches you can use
software diagnostics to verify proper communication-line
health. The LEDs on each individual switch provide health
status information.
Scalable in small increments. The DeltaV system provides
a package with very low initial cost. You are able to expand
the system readily and economically by adding hardware
incrementally to your system.
Redundant. The DeltaV Control Network is a fully redundant
communication network. Nodes may also be connected using
a simplex network, but this is not a recommended practice.
DeltaV Control Network Description
and Specification
October 2014
The DeltaV Control Network supports the use of autonegotiated 10-half, 100-half, 10 full, and 100-full duplex
communications where the industry standard auto-negotiation
process determines the highest speed at which two devices
will communicate with each other. The latest DeltaV network
products make use of gigabit Ethernet for switch-to-switch
communications and can support distances up to 108 Km
using standard product fiber optic communications.
The DeltaV workstations and controllers contain two
Ethernet ports to provide the recommended redundant
communications. Early models of DeltaV controllers supported
10 megabit Ethernet at half-duplex only. The latest DeltaV
controllers auto-negotiate to any speed and duplex from
10-half to 100-full, depending on what the controller is
attached to. The workstations do the same: they auto-negotiate
to the highest speed and duplex available from their
attached device.
Ethernet Cable
The DeltaV system requires the use of Category 5e screened
(ScTP) cable for the 10/100/1000 BaseT/TX control network.
The DeltaV Control Network can be physically connected
as a star or cascade (daisy-chain) topology. Other network
configurations are possible, such as a combination of a star
and cascade topology. (DeltaV does not support network
ring topologies).
Fiber-optic Wiring
Refer to the latest DeltaV system installation and planning
manual(s) for details of network layouts and network cable
shielding requirements and power and grounding requirements
for the overall DeltaV distributed control system.
Fiber-optic cabling should also be used where wire runs are
longer than 100 meters (328 ft).
The Control Network can use one or more Ethernet switches
for communications connections. To be supported by Emerson
Process Management, the DeltaV control network must be
installed using the network equipment listed in this document.
DeltaV Smart Switch
Wiring
The maximum twisted-pair cable length for the DeltaV
control network for any Ethernet-connected device is
100 meters (328 feet). If longer cable distances are needed
for this workstation-to-switch, controller-to-switch, or switchto-switch connections, there are various fiber-optic cable
and transceiver solutions available from Emerson Process
Management as a standard supported solution. For special
network designs that go beyond the supported diagrams
shown in the DeltaV installation and planning manuals, consult
with the Emerson Process Management SureService team.
2
Because fiber-optic cables do not conduct electricity, they
should be used in connections between buildings or in plant
areas where electromagnetic interference is present.
DeltaV Smart Switches
The DeltaV Network “Smart” switches are the next generation
in the use of commercial off-the-shelf (COTS) components in
control systems. Called “Built-for-purpose” commercial off the
shelf these switches combine the lower cost of off-the-shelf
components with DeltaV specific software and features to
make them more integrated and plug-and-play in the
control network.
DeltaV Smart Switches require no configuration to function in
the DeltaV network. Accessing the advanced features takes only
minor configuration that is easy to perform using the DeltaV
Smart Switch Command Center and secured so you can’t
incorrectly configure any switching functions that impact the
performance of the DeltaV system.
www.EmersonProcess.com
DeltaV Control Network Hardware
October 2014
The built-for-purpose switch also allows the DeltaV system to
provide an auto port lockdown advanced security feature that
is easy for a control system user to implement: an increasingly
important product feature in today’s hostile environment.
The Smart Switch will generate network, device and security
alarms to operator workstations. The built-in network and
switch diagnostics provide network and switch diagnostic
information to the Smart Switch Command Center without
the use of third party SNMP applications.
Please see the PDS “DeltaV Network Smart Switches” for
complete ordering information and detailed specifications
of the DeltaV Smart Switches.
DeltaV Smart Switches are the preferred switch to be used
within the DeltaV network.
The DeltaV Smart Switch provides a full family of built for purpose
switches that are easy to use and peovide advnaced security
features to help protect your DeltaV networkfrom cyber incidents
Ordering Information
DIN Rail Mount Fixed Port Smart Switches
Ordering Number
Description
All FP20 Switches have 8 total ports
VE6041F01C1
Smart 6-Port (RJ45) 10/100BASE-TX Switch with two RJ45 10/100BASE-TX
Uplink Ports (FP20-6TX2TX)
VE6041F02C1
Smart 6-Port (RJ45) 10/100BASE-TX Switch with two Uplink Ports -- one RJ45 10/100BASE-TX
and one SC 100BASE-FX Multimode (FP20-6TX1MM1TX)
VE6041F03C1
Smart 6-Port (RJ45) 10/100BASE-TX Switch with two Uplink Ports -- one RJ45 10/100BASE-TX
and one SC 100BASE-FX Single Mode (FP20-6TX1SM1TX)
VE6041F04C1
Smart 6-Port (RJ45) 10/100BASE-TX Switch with two Uplink Ports – one RJ45 10/100BASE-TX
and one SC 100BASE-FX Single Mode, Long Haul (FP20-6TX1SMLH1TX)
VE6041F05C1
Smart 6-Port (RJ45) 10/100BASE-TX Switch with two SC 100BASE-FX Multimode Uplink Ports
(FP20-6TX2MM)
VE6041F06C1
Smart 6-Port (RJ45) 10/100BASE-TX Switch with two SC 100BASE-FX Single Mode Uplink Ports
(FP20-6TX2SM)
VE6041F07C1
Smart 6-Port (RJ45) 10/100BASE-TX Switch with two SC 100BASE-FX Single Mode, Long Haul
Uplink Ports (FP20-6TX2SMLH)
3
www.EmersonProcess.com
DeltaV Control Network Hardware
Ordering Number
October 2014
Description
VE6042S2C1
Smart Ethernet Switch Module and Backplane for two VE6045-series Media Modules (MD20-8)
VE6042S4C1
Smart Ethernet Switch Module and Backplane for four VE6045-series Media Modules (MD20-16)
VE6042S6C1
Smart Ethernet Switch Module and Backplane for six VE6045-series Media Modules (MD20-24)
VE6043S2C1
Smart Switch Module, Gigabit Uplink Module, and Backplane for two VE6045-series Media
Modules (MD30-8 + MD4-2TX/SFP)
VE6043S4C1
Smart Switch Module, Gigabit Uplink Module, and Backplane for four VE6045-series Media
Modules (MD30-16 + MD4-2TX/SFP)
VE6043S6C1
Smart Switch Module, Gigabit Uplink Module, and Backplane for six VE6045-series Media
Modules (MD30-24 + MD4-2TX/SFP)
Interface modules to populate the VE6042 and VE6043 Switches
Description
Media Modules below can be used on any of the MD series switches above
VE6045M01C1
Smart 2-Port Media Module; Two 100BASE-FX Fiber-Optic Multi-Mode SC Ports (MD2-2FXM2)
VE6045M02C1
Smart 2-Port Media Module; Two 100BASE-FX Fiber-Optic Single Mode SC Ports (MD2-2FXS2)
VE6045M03C1
Smart 4-Port Media Module; Four 10/100BASE-TX Copper RJ45 Ports (MD2-4TX1)
VE6045M04C1
Smart 4-Port Media Module; Two 10/100BASE-TX Copper RJ45 Ports,
and two 100BASE-FX Fiber-Optic Multi-Mode SC Ports (MD3-2FXM2/2TX1)
VE6045M05C1
Smart Switch; 4-Port Media Module; Two 10/100BASE-TX Copper RJ45 Ports,
and two 100BASE-FX Fiber-Optic Single Mode SC Ports (MD3-2FXS2/2TX1)
VE6045M06C1
Smart 4-Port Media Module; Four 100BASE-FX Fiber-Optic Multi-Mode SC Ports (MD3-4FX/M2)
VE6045M07C1
Smart 4-Port Media Module; Four 100BASE-FX Fiber-Optic Multi-Mode ST Ports (MD3-4FX/M4)
VE6045M08C1
Smart 4-Port Media Module; Four 100BASE-FX Fiber-Optic Single-Mode SC Ports(MD3-4FXS2)
VE6045M09C1
Smart 4-Port Media Module; Two 10/100BASE-TX Copper RJ45 Ports,
and two 100BASE-FX Fiber-Optic Multi-Mode ST Ports (MD3-2FXM4/2TX1)
VE6045M10C1
Smart 4-Port Media Module; Three 10/100BASE-TX Copper RJ45 Ports,
and one 100BASE-FX Fiber-Optic Single Mode SC Ports (MD3-1FXS2/3TX1)
VE6045M11C1
Smart 4-Port Power-over-Ethernet (PoE) Media Module;
All Ports are 10/100BASE-TX Copper RJ45 (MD2-4TX1-PoE)
All of the VE6041, VE6042, VE6043 and VE6045 Smart Switches above are also available in Extend Specification versions for use in more
rugged environments. See “PDS DeltaV Smart Switches” for details and ordering information.
4
www.EmersonProcess.com
DeltaV Control Network Hardware
October 2014
Rack Mount Smart Switches
8 and 24 Port non-Modular Rack Mount Switch
Switch VE Number
Description
The VE6046 and VE6047 are fixed 8 or 24 port copper switches
VE6046P1 thru P4
Smart 24-Port Switch; Each port is 10/100BASE-TX Copper RJ45; Includes two RJ45 Uplink ports
and two slots for VE6050-series Transceiver Modules Power Cord (RM100-24TX)
(This switch is not modular)
VE6047P1 thru P4
Smart 8-Port Switch; Each port is 10/100BASE-TX Copper RJ45; Includes two RJ45 Uplink ports
and two slots for VE6050-series Transceiver Modules Power Cord (RM100-8TX)
(This switch is not modular)
24 Port Modular Rack Mount Switch
Switch VE Number
Description
The VE6048 switch is a base chassis with 8 fixed copper ports and 2 gigabit uplink ports
VE6048R1P1 thru P4
Smart 8-Port Switch; Each port is 10/100BASE-TX Copper RJ45; Includes two RJ45 Uplink ports
and two slots for VE6050-series Transceiver Modules Includes two expansion bays to add ports;
Simplex Power Supply; Power Cord (RM100-Base Module)
VE6048R2P1
Smart 8-Port Switch; Each port is 10/100BASE-TX Copper RJ45; Includes two RJ45 Uplink ports
and two slots for VE6050-series Transceiver Modules; Includes two expansion bays to add ports;
Redundant Power Supply; Power Cords (RM100-RP Base Module)
Redundant Power Supplies
8 Port Interface Modules to Customize the VE6048 Switch
Switch VE Number
Description
The VE6049 modules are installed in the VE6048 to create the specific switch configuration required
VE6049M01
8-Port Expansion Module for VE6048-series Smart Switches;
Each Port is 10/100BASE-TX Copper RJ45 (RM100-EM8TX)
VE6049M02
8-Port Expansion Module for VE6048-series Smart Switches;
Each Port is 100BASE-FX Fiber-Optic Multi-Mode SC (RM100-EM8MMFX)
5
www.EmersonProcess.com
DeltaV Control Network Hardware
October 2014
VE6049M03
8-Port Expansion Module for VE6048-series Smart Switches;
Each Port is 100BASE-FX Fiber-Optic Single-Mode SC (RM100-EM8SMFX)
VE6049M04
8-Slot Expansion Module for VE6048-series Smart Switches. The slots can have any combination
of VE6050-series 100Mb Transceivers installed in them. (RM100-EM8SFP)
The following transceivers are used in the VE6043, VE6046, VE6047 and VE6048 switches.
Fiber Optic SFP Transceivers for use in DeltaV Switches Description
VE6050T01
Transciever for Smart Switches: 1 Gigabit Ethernet; Single Mode Long Haul, for up to
120 Kilometers of fiber-optic cable (M-SFP-LH+/LC) [This SFP Module is NOT compatible
with Extended Spec usage – not available with extended temperature specifications
VE6050T02
Transciever for Smart Switches; 1 Gigabit Ethernet; Single Mode Long Haul,
for up to 80 Kilometers of fiber-optic cable (M-SFP-LH/LC-EEC)
VE6050T03
Transciever for Smart Switches; 1 Gigabit Ethernet; Single Mode, for up to 20 Kilometers of
fiber-optic cable (M-SFP-LX/LC EEC)
VE6050T04
Transciever for Smart Switches; 100 Megabit Ethernet, Single Mode, for up to 100 Kilometers of
fiber-optic cable (M-FAST SFP-LH/LC-EEC)
VE6050T05
Transciever for Smart Switches; 100 Megabit Ethernet; Single Mode, for up to 65 Kilometers of
fiber-optic cable (M-FAST SFP-SM+/LC-EEC)
VE6050T06
Transciever for Smart Switches; 100 Megabit Ethernet; Single Mode, for up to 25 Kilometers of
fiber-optic cable (M-FAST SFP-SM/LC-EEC)
VE6050T07
Transciever for Smart Switches; 1 Gigabit Ethernet; Multi-mode, for up to 550 meters of
fiber-optic cable (M-SFP-SX/LC EEC)
VE6050T08
Transciever for Smart Switches; 100 Megabit Ethernet: Multi-Mode; for up to 5 Kilometers of
fiber-optic cable (M-FAST SFP-MM/LC-EEC)
6
www.EmersonProcess.com
DeltaV Control Network Hardware
October 2014
The switches below are unmanaged switches for use in smaller DeltaV systems where the features of the smart switch may
not be required
Unmanaged DIN Rail Mount Switches
The Emerson Fiber-optic to Copper Ethernet switches are suitable for use in Class 1 Div. 2 and Class 1 Zone 2 areas to provide an
energy-limited fiber-optic link to IS-classed areas. They can also be used as unmanaged switches on the DeltaV communications
network for connections between controllers and DeltaV workstations.
Note: These switches should not be used in networks between the controller and CIOC. The DeltaV Smart Switch must be
used in the network between the controllers and CIOC.
VE6019 Fiber-optic (1) to Copper (4) Ethernet Switch
Description
Specifications
Ports
4 x10/100BASE-TX, Twisted-pair ports, RJ45 connector, auto-crossing,
auto-negotiation 1 x 100BASE –FX, Multi-mode port, MT-RJ connector
Power
Operating voltage 24VDC (18 to 32VDC)
Current consumption 250 mA max @ 24 VDC
Redundant power connections
Cabling
Twisted pair (TP) 0-100 m
Fiber Type: micron muiltmode fiber (MM) 62.5/125 or 50/125 µm 0-2000m
Attenuation: ≤11dB (62.5/125), ≤8 dB (50/125)
Front Panel LEDs
Power, link status, collision/duplex and speed
Environmental
Operating temp -40 to +70°C
Storage Temp -40 to +85°C
ISA 74.04 G3 Airborne contaminates
Dimensions (WxHxD)
35mm x 100mm x 114mm
Mounting DIN rail 35MM
Weight
206g
Protection Class
IP20
EMC
EN 61326 with Class A emissions, Annex A immunity
Safety
CSA-C22.2 No 1010.1-92
ATEX
EN 60079-15 Zone 2, fiber port IS EEx nA [op is] IIC T4
IEC 60079-28 (Protection of equipment and transmission systems using optical radiation)
FM
3611 Class1 Div2, Class 1 Zone 2
NAMUR
NE21
7
www.EmersonProcess.com
DeltaV Control Network Hardware
October 2014
VE6020 Fiber-optic (4) to Copper (1) Ethernet Switch
Description
Specifications
Ports
4 x100BASE-FX, Multi-mode ports, MT-RJ connector
1 x 10/100BASE–TX, Twisted-pair port, RJ45 connector, auto-crossing, auto-negotiation
Power
Operating voltage 24VDC (18 to 32VDC)
Current consumption 350 mA max @ 24 VDC
Redundant power connections
Cabling
Twisted pair (TP) 0-100 m
Fiber Type: micron muiltmode fiber (MM) 62.5/125 or 50/125 µm 0-2000m
Attenuation: ≤11dB (62.5/125), ≤8 dB (50/125)
Front Panel LEDs
Power, link status, collision/duplex and speed
Environmental
Operating temp -40 to +70°C
Storage Temp -40 to +85°C
ISA 74.04 G3 Airborne contaminates
Dimensions (WxHxD)
52.5mm x 100mm x 114mm
Mounting DIN rail 35MM
Weight
227g
Protection Class
IP20
EMC
EN 61326 with Class A emissions, Annex A immunity
Safety
CSA-C22.2 No 1010.1-92
ATEX
EN 60079-15 Zone 2, fiber port IS EEx nA [op is] IIC T4
Iec 60079-28(Protection Of Equipment And Transmission Systems Using Optical Radiation)
FM
3611 Class1 Div2, Class 1 Zone 2
NAMUR
NE21
8
www.EmersonProcess.com
DeltaV Control Network Hardware
October 2014
Unmanaged Rack Mount Switches
(For detailed technical information please see www.alliedtelesyn.com). These units include a rack mount kit and can be installed
on 19” rack rails.
When ordering, please make sure to use the model number for destination country. The appropriate electrical connectors will be
selected for compatibility with local power requirements.
Note: These switches should not be used in networks between the controller and CIOC. The DeltaV Smart Switch must be
used in the network between the controllers and CIOC.
Description
8-Port 10/100BASE-TX Ethernet Switch
Model Number
VE6017F0P1 North American power cord
VE6017F0P2 United Kingdom power cord
VE6017F0P3 European power cord
VE6017F0P4 Australian power cord
Allied Telesyn AT-FS708 switch
8-Port 10/100BASE-TX Ethernet Switch (with
100BASE-FX port supports up to 2KM fiber.)
VE6017F1P1 North American power cord
VE6017F1P2 United Kingdom power cord
VE6017F1P3 European power cord
VE6017F1P4 Australian power cord
Allied Telesyn AT-FS 709FC
Cisco Switches
With the introduction of the DeltaV Smart Switches, the
Emerson branded smart switches are the preferred switch for
use in the DeltaV network. As such the Cisco switch information
is no longer included in this document as they are no longer
quoted on new DeltaV Systems.
Cisco switches continue to be supported for use as spares for
existing switches, for system expansion where compatibility
with existing switches is desired. Cisco switches and DeltaV
9
Smart Switches can be mixed on a DeltaV system. DeltaV Smart
Switch can be used in some cases to replace existing Cisco
switches. For further information on this topic please see the
whitepaper “DeltaV Smart Switches Displace Cisco Switches”
Product information on the Cisco Switches available for use
in a DeltaV System can be obtained from your local DeltaV
sales office.
www.EmersonProcess.com
DeltaV Control Network Hardware
October 2014
Related Products
„„
PDS DeltaV Smart Switch. For more information on the
Smart Switches
„„
DeltaV Security Manual. For information on designing a
secure DeltaV network
„„
PDS DeltaV Controller Firewall. For information on
advanced security solutions for DeltaV networks
„„
WP DeltaV Smart Switch Displace Cisco Switches.
For information on Cisco support
© Emerson Process Management 2014. All rights reserved.
Emerson Process Management
Emerson is a trademark of Emerson Electric Co. The DeltaV logo is a mark of one of
Emerson Process Management family of companies. All other marks are property of their
respective owners.
Asia Pacific: 65.6777.8211
Europe, Middle East: 41.41.768.6111
North America, Latin America:
+1 800.833.8314 or
+1 512.832.3774
www.EmersonProcess.com/DeltaV
The contents of this publication are presented for informational purposes only, and while every
effort has been made to ensure their accuracy, they are not to be construed as warrantees or
guarantees, express or implied, regarding the products or services described herein or their
use or applicability. All sales are governed by our terms and conditions, which are available on
request. We reserve the right to modify or improve the design or specification of such products
at any time without notice.
Download PDF