Elation | Power Wash 575E | Specifications | Elation Power Wash 575E Specifications

Design Wash 575E
Elation Professional
6122 S. Eastern Ave.
Los Angeles, CA. 90040
www.elationlighting.com
Rev. 06/06/2008
Design Wash 575E™
Contents
1.
General Information……………………………………………………………………… 3
a. Introduction………………………………………………………………………. 3
b. Unpacking………………………………………………………..…………..…
c.
3
Customer Support…………………………………………….………………… 3
d. Warranty Registration……………………………………………………..…… 4
e. Discharge Lamp Warning……………………………………………………… 4
2.
Safety Instructions………………………………………………………........…………. 6
3.
Features…………………………………………………………………………………… 8
4.
General Guidelines………………………………………………………………………. 9
5.
Lamp Installation…………………………………………………………………………. 10
a. Lamp installation…………………………………………………….………….. 10
b. Lamp optimization……………………………………………………..………… 11
6.
Mounting and Installation………………………………………………………….……. 13
a. Mounting Positions……………………………………………………………… 13
b. Mounting Points…………………………………………………………………. 14
c.
7.
Securing………………………………………………………………………….. 15
Understanding DMX……………………………………………………………………... 16
a. DMX Connections………………………………………………………………. 16
b. DMX Terminator…………………………………………………………………. 17
c.
8.
3-Pin to 5-Pin Conversion………………………………………………………. 18
Fixture Menu……………………………………………………………………………… 19
a. Menu functions………………………………………………………………….. 21
9.
Operation…………………………………………………………………………………..29
10. DMX Channel Traits…………………………………………………………………….. 32
a)
DMX Channel Values……………………………………………………………… 33
11. FUSE Replacement………………………………………………………………………. 36
12. Error Codes………………………………………………………………………………. 37
13. Cleaning and Maintenance……………………………………………………………… 40
14. Warranty…………………………………………………………………………………... 41
15. Photometric Data………………………………………………………………………… 43
16. Dimensional Drawings………………………………………………….……………….. 44
17. Circuit Schematic………...………………………………………………………………. 45
18. Technical Specifications…………………………………………...………….………… 47
©Elation Professional®
2
Design Wash 575E™
Design Wash 575E™
1. GENERAL INFORMATION
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and
reliable lighting fixtures on the market today! The Design Wash 575E™ has been designed
to perform reliably for years when the guidelines in this booklet are followed. Please read
and understand the instructions in this manual carefully and thoroughly before attempting to
operate this unit. These instructions contain important information regarding safety during
use and maintenance.
UNPACKING: Thank you for purchasing the Design Wash 575E™ by Elation Professional®.
Every Design Wash 575E™ has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that may have occurred
during shipping. If the carton appears to be damaged, carefully inspect your unit for damage
and be sure all accessories necessary to operate the unit have arrived intact. In the event
damage has been found or parts are missing, please contact our customer support team for
further instructions. Please do not return this unit to your dealer without first contacting
customer support at the number listed below.
CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to provide
set up help and to answer any question should you encounter problems during your set up
or initial operation. You may also visit us on the web at www.elationlighting.com for any
comments or suggestions. For service related issue please contact Elation Professional®.
Service Hours are Monday through Friday 8:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice:
(323) 582-3322
Fax:
(323) 832-9142
E-mail:
support@elationlighting.com
Forum:
www.ElationLighting.com/forum
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to
rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
yourself, doing so will void your manufactures warranty.
©Elation Professional®
3
Design Wash 575E™
Design Wash 575E™
Please do not discard the shipping carton in the trash. Please recycle whenever possible.
WARRANTY REGISTRATION: The Design Wash 575E™ carries a two year (730 days)
limited warranty. Please fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be clearly written
on the outside of the return package. A brief description of the problem as well as the R.A.
number must also be written down on a piece of paper and included in the shipping
container. If the unit is under warranty, you must provide a copy of your proof of purchase
invoice. Items returned without a R.A. number clearly marked on the outside of the package
will be refused and returned at customer’s expense. You may obtain a R.A. number by
contacting customer support at (323) 582-3322.
DISCHARGE LAMP WARNING: This fixture is fitted with a discharge
lamp, which is highly susceptible to damage if improperly handled.
Never touch the lamp with your bare hands, as the oil from your hands
will shorten lamp life. Also, never move the fixture until the lamp has
had ample time to cool. Remember, lamps are not covered under
warranty conditions.
UV RADIATION: This fixture emits intense UV radiation, which is harmful to the eyes and
skin. The intense luminance of the lamp can cause severe damage to the retina. Never
operate this fixture with the protective covers removed, these covers have been specially
designed to shield against UV radiation.
Epileptic Warning: Those suffering from epilepsy should avoid looking directly into the
lamp at all times.
Avoid switching the fixture on and off repeatedly in short intervals, as this will reduce lamp
life and intensity.
To achieve the intensity associated with discharge lamps, these lamps use a gas sealed in a
high-pressure environment to emit a brilliant output. Due to the high pressure involved with
the construction of the lamp, the lamp may explode during prolonged extensive use. This
©Elation Professional®
4
Design Wash 575E™
Design Wash 575E™
risk is increased with age; added care is encouraged when dealing with older lamps. Thus,
lamp should always be replaced at the end of their recommended duty cycle. Extreme
caution should be used when operated this or any fixture fitted with a gas discharge lamp.
Never open this fixture while in use!
During the initial operation of this fixture, a light smoke or smell may emit from the interior of
the fixture. This is a normal process and is caused by excess paint in the interior of the
casing burning off from the heat associated with the lamp and will decrease gradually over
time.
This device falls under protection-class 1. Therefore it is essential that the device be
grounded properly.
Qualified personnel should perform all electrical connections.
Be sure the available voltage matches the voltage requirements of the unit.
Be sure the power cord is never crimped or damaged. If the power cord is damaged, replace
it immediately with a new one of similar power rating.
Always disconnect from main power before performing any type of service or any cleaning
procedure.
Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of
the cord.
Please be aware that damages caused by manual modifications to the device are not
subject to warranty.
©Elation Professional®
5
Design Wash 575E™
Design Wash 575E™
2. SAFETY INSTRUCTIONS
The Design Wash 575E™ is an extremely sophisticated piece of
electronic equipment. To guarantee a smooth operation, it is
important to follow the guidelines in this manual. The
manufacturer of this device will not accept responsibility for
damages resulting from the misuse of this fixture due to the
disregard of the information printed in this manual.
1. Always be sure that the fan and the air inlets remain clean and are never blocked.
Allow about 6” (15cm) between this fixture and other devices or a wall to allow for
proper cooling.
2. Never touch the fixture during normal operation. This can cause severe personal
injuries and/or damage to the fixture.
3. Be sure to unplug the DESIGN WASH 575E™ from the power outlet before
performing any service related issues.
4. Lamp Replacement; Allow at least 30 minutes after disconnecting main power
before you open the DESIGN WASH 575E™. To prevent personal injury, never
touch the lamp if you are not absolutely sure it has cooled.
5. Never look directly into the lamp beam. You risk injury to your retina, which may
induce blindness.
6. Be sure to track and record the lamp running time. The lamp should be changed at
the end of the specified lamp life, regardless of lamp output. You may also have to
change the lamp if it shows any deformations or damage. The same is with all
glass components, color filters, lenses and mirrors.
7. For safe operation, follow the Installation guide described in chapter two of this
manual. Operating the DESIGN WASH 575E™ without suited safety aids such as
safety cables or clamps can increase the risk of damage and/or personal injury.
8. Installation should only be performed by qualified and certified personnel.
9. When mounting this fixture, use only the original rigging parts included with this
fixture. Any structural modification will void the original manufactures warranty and
©Elation Professional®
6
Design Wash 575E™
Design Wash 575E™
may increase the risk of damage and/or personal injury.
10. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture.
11. Do not attempt to operate this fixture if the power cord has become damaged or
frayed.
Important Notice: Damages resulting from the disregard of safety and general user
instructions found in this user manual are not subject to any warranty claims.
©Elation Professional®
7
Design Wash 575E™
Design Wash 575E™
3. FEATURES
•
Pan 540° or 630˚ (User selectable) / Tilt 265°
•
Built-In Macros (color)
•
3 operation mode: DMX Controlled, Stand-Alone or Sound Activated
•
Color Wheel: 8 colors plus white (including UV filter), with rainbow effect
•
CMY Variable Color Mixing
•
Easy to Navigate On-Board LCD Menu
•
Animation Effect Wheel
•
Strobe Effect: 0~10 flashes per second or random strobe
•
Bright Phillips Gold MSR 575/2 SA DE Lamp (575w / 7200K / 750Hrs / 43,000Lm)
•
Linear Dimmer from 0%~100%
•
RDMX (Remote DMX addressing from any DMX console)
•
Auto test for all functions
•
Motorized Linear Zoom (13˚ ~ 50˚)
•
Glass Dichroic Reflector for Even Lamp Output
•
USITT DMX-512 Complaint
o 16 DMX Channels (16bit Operation)
o 14 DMX Channels (8bit Operation)
•
8 User Assignable Program Presets - Internal Program: Edit and save programs to
the incorporated EEPROM. Maximum of 48 scenes.
©Elation Professional®
8
Design Wash 575E™
Design Wash 575E™
4. GENERAL GUIDELINES
This fixture is a professional lighting effect designed for use on stage, in nightclubs, in
theatres, etc. Do not attempt operation or installation without a proper knowledge on how to
so.
This fixture was designed for indoor use only.
Consistent operational breaks may ensure that the fixture will function properly for many
years to come.
Do not shake the fixture around. Avoid brute force when installing or operating the device.
While choosing an installation location, please be sure that the fixture will not be exposed to
extreme heat, moisture or dust. The minimum distance between the fixture and a wall or flat
surface should be at least .5 meter (about 1.5ft).
Always install the fixture with an appropriate safety cable. When installing the fixture in a
suspended environment always be to use mounting hardware no less than M10 x 25 mm,
also be sure the hardware is insert in the pre-arranged screw holes in the base of the fixture.
When using the quick release “Omega” cam-lock system, be sure the four quick lock
fasteners are locked in the quick lock holes correctly.
Do not attempt to operate this fixture until you have familiarized yourself with its functions.
Do not permit operation by persons not qualified for operating this type of theatrical fixture,
most damages are the result of operations by nonprofessionals.
Please use the original packaging to transport the fixture in for service.
©Elation Professional®
9
Design Wash 575E™
Design Wash 575E™
5. LAMP INSTALLATION INSTRUCTIONS
For a proper and safe lamp change, please read this chapter carefully and follow all
instructions.
Safety Regulations
•
Disconnect the unit’s main power supply.
•
Allow the unit to cool for at least 30 minutes before attempting any type of service.
•
Before you put the Design Wash 575E™ into operation be sure all covers have
been replaced, otherwise you risk damage to the retina and expose to UV radiation!
•
Replace the lamp with an approved replacement type. Be sure to follow all the lamp
handleing procedures included with your new lamp. Never handle the new lamp
with your bare hands, the oils from your skin may damage the lamp. Always replace
with the lamp with a lamp that meets the orginal lamp specification, failure to do so
may damage the unit and will void your manufactures warranty.
Installation Procedure:
1. Set the fixture on a flat surface and remove the four screws labeled “A” “B,” “C,” and
“D” found on the back plate of the head assembly.
2. Gently pull out the lamp/socket assembly to access the lamp.
3. Gently remove the old lamp by grasping it by metal ends.
4. Insert the new lamp securely, locking the lamp in place as illustrated in the diagram
on the next page. Orientate the lamp filler tube towards the backside of the reflector.
Before reassembling the unit, be sure the new lamp is securely seated in the lamp
socket. Always be sure to only use specified lamp types! (MSR 575 SA/2 DE lamp or
equivalent).
©Elation Professional®
10
Design Wash 575E™
Design Wash 575E™
OK 
NO

5. Once the lamp has been inserted into the socket, gently slide the socket assembly
back into place and secure with the four retaining screws.
6. Reset the lamp run time in the system menu.
7. Always be sure to optimize the lamp after lamp replacement.
Lamp Optimization
The lamp orientation and optimization must be adjusted after every lamp change. This
procedure centers the lamp in the reflector. Proper optimization will increase lamp life and
ensure a bright, crisp, and even output. Improper optimization may add a yellow tint to the
lamp output and reduce intensity. The minimum deviation amount is 1.0mm. Running the
fixture within a lower deviation can cause damage to the lamp and/or lens.
The Design Wash 575E™ lamp holder is aligned at the factory. However, due to slight
imperfections in all lamps, fine adjustments will improve light performance. Please follow the
procedure below for proper lamp optimization:
1. Using either a DMX controller or the control panel on the unit, strike the lamp and
focus the light on a flat surface (beam open, white, no gobo, no effect).
2. Center the hot-spot (the brightest part of the beam) using the 3 adjustment screws
labeled 1, 2, and 3 as illustrated on the next page. Turn one screw at a time to drag
the hot-spot diagonally across the projected image. If you cannot detect a hot-spot,
adjust the lamp until the light is even.
©Elation Professional®
11
Design Wash 575E™
Design Wash 575E™
3. To reduce a hot-spot, pull the lamp in by turning all three screws clockwise a 1/4-turn
at a time until the light is evenly distributed.
4. If the light is brighter around the edge than it is in the center, or if light output is low,
the lamp is too far back in the reflector. "Push” the lamp out by turning each of the
adjustment screws ("1, 2, 3”) counterclockwise turn until the light is bright and evenly
distributed.
Please remember that a MSR 575 SA/2 DE lamp is not a hot-restrike lamp therefore, you
must wait approximately 15 minutes before you can attempt to strike the lamp once it has
been turned off.
©Elation Professional®
12
Design Wash 575E™
Design Wash 575E™
6. MOUNTING AND INSTALLATION
Cautions:
For added protection mount the fixtures in areas outside walking paths, seating areas, or in
areas were the fixture might be reached by unauthorized personal.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
Mounting
The DESIGN WASH 575E™ is fully operational in two different mounting positions, hanging
upside-down from a ceiling, or set on a flat level surface (see illustration on next page). Be
sure this fixture is kept at least 0.5m away from any flammable materials (decoration etc.).
Always use and install the supplied safety cable as a safety measure to prevent accidental
damage and/or injury in the event the clamp fails.
Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE0711-217
for proper installation in Europe To ensure proper installation, only
qualified staff should attempt installation.
©Elation Professional®
13
Design Wash 575E™
Design Wash 575E™
Mounting points
Overhead mounting requires extensive experience, including amongst others calculating
working load limits, a fine knowledge of the installation material being used, and periodic
safety inspection of all installation material and the fixture. If you lack these qualifications, do
not attempt the installation yourself. Improper installation can result in bodily injury.
CAUTION!
Be sure all electrical connections are performed by a qualified
electrician.
Be sure to complete all rigging and installation procedures before connecting the main
power cord to the appropriate wall outlet.
Clamp Mounting
The Design Wash 575E™ provides a unique mounting bracket assembly that integrates the
hanging yoke as well as the safety cable rigging point in one unit (see the illustration below).
©Elation Professional®
14
Design Wash 575E™
Design Wash 575E™
When mounting this fixture to truss be sure to secure an appropriately rated clamp to the
hanging yoke using a M10 screw fitted through the center hole of the hanging yoke. As an
added safety measure be sure to attached at least one properly rated safety cable to the
fixture using on of the safety cable rigging point integrated in the bracket assembly
Securing the DESIGN WASH 575E™
Regardless of the rigging option you choose for your Design Wash 575E™ always be sure
to secure your fixture with a safety cable. The fixture provides a built-in rigging point for a
safety cable on the hanging bracket as illustrated above. Be sure to only use the designated
rigging point for the safety cable and never secure a safety cable to a carrying handle.
©Elation Professional®
15
Design Wash 575E™
Design Wash 575E™
7. UNDERSTANDING DMX
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most
lighting and controller manufactures as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from the controller to the
fixture. DMX data is sent out as serial data that travels from fixture to fixture via the DATA
“IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have
a DATA “OUT” terminals). DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a single controller, as long
as all fixtures and the controller are DMX compliant. To ensure proper DMX data
transmission, when using several DMX fixtures try to use the shortest cable path possible.
The order in which fixtures are connected in a DMX line does not influence the DMX
addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in
a DMX line, at the beginning, at the end, or anywhere in the middle. Therefore, the first
fixture controlled by the controller could be the last fixture in the chain. When a fixture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address
1 to that fixture, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): The
Design Wash 575E™ can be controlled via DMX-512 protocol. The Design Wash 575E™ is
a 24 channel DMX fixture. The DMX address is set electronically using the controls on the
LCD menu. Your fixture and your DMX controller require a standard 3-pin or 5-pin XLR
connector for data input and data output (Figure below is of a 3-Pin XLR connector). If you
are making your own cables, be sure to use standard two conductor shielded cable (This
cable may be purchased from your Elation dealer or at most professional lighting retailers).
Your cables should be made with a male and female XLR connector on either end of the
cable. Also, remember that DMX cable must be daisy chained and cannot be split. unless you
are using an approved DMX splitter such as the Elation Opto Branch 4™ or DMX
Branch/4™.
©Elation Professional®
16
Design Wash 575E™
Design Wash 575E™
Be sure to follow the pin configuration chart below when making your own cables. Do not
use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the
ground lug or allow the shield conductor to come in contact with the XLR’s outer casing.
Grounding the shield could cause a short circuit and erratic behavior.
DMX-512 control connection
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the
other side to the male 3-pin XLR input of the moving head (Please refer to the diagram
below.). You can chain multiple moving heads together through serial linking. Always be sure
daisy chain your in and out data connections, never split or “Y” your DMX connections
unless you are using an approved DMX splitter such as the Elation Opto Branch 4™ or DMX
Branch/4™.
DMX-512 connection with DMX terminator
When longer runs of cable are used, you may need to use a terminator on the last fixture to
avoid erratic behavior. A terminator is a 90-120 ohm 1/4 watt resistor that is connected
between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This fixture is inserted
in the female XLR connector of the last fixture in your daisy chain to terminate the line. Using
©Elation Professional®
17
Design Wash 575E™
Design Wash 575E™
a cable terminator (Elation part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
Fixture DMX addressing;
All fixtures should be given a DMX starting address when using a DMX controller, so the
correct fixture responds to the correct control signal. This digital starting address is the
channel number from which the fixture starts to “listen” to the digital control information sent
out from the DMX controller. The allocation of this starting DMX address is achieved by
setting the correct DMX address on the digital display located on the head of the fixture.
You can set the same starting address for all fixtures or a group of fixtures, or set different
address for each individual fixture. Be advised that setting all you fixtures to the same DMX
address will subsequently control all fixtures in the same fashion, in other words, changing
the settings of one channel will affect all the fixtures simultaneously.
If you set each fixture to a different DMX address, each unit will start to “listen” to the
channel number you have set, based on the quantity of control channels (DMX channels) of
each fixture. That means changing the settings of one channel will only affect the selected
fixture.
In the case of the Design Wash 575E™, which is a 16 channel fixture, you should set the
starting DMX address of the first unit to 1, the second unit to 17 (16 + 1), the third unit to 33
(16 + 17), and so on.
©Elation Professional®
18
Design Wash 575E™
Design Wash 575E™
8. FIXTURE MENU
On-Board System Menu: The DESIGN WASH 575E™ comes with an easy to navigate
system menu. This next section will detail the functions of each command in the system
menu.
LCD Control Panel: The control panel located on the side of the fixture allows you to
access the main menu and make necessary adjustments to the Design Wash 575E™.
During normal operation, tapping the “MODE/ESC” key once will access the fixture’s main
menu. Once in the main menu you can navigate through the different functions and access
the sub-menus with the Up and Down buttons. Once you reach a field that requires
adjusting, tap the ENTER button to activate that field and use the UP and Down button to
adjust the field. Tapping the Enter button once more will confirm your setting. You may exit
the main menu at any time without making any adjustments by tapping the MODE/ESC
Information
Function Mode
button.
Set DMX Address
Value Display
Set To Slave
Auto Program
Music Control
A001~AXXX
PAN Moving……
Slave1,Slave2,Slave3
Master / Alone
Master / Alone
DMX address setting
DMX value display
Slave setting
Auto program
Music control
Time Information
Current Time
Total Run Time
Total Lamp Time
Lamp Off Time
Clear Lamp Time
XXXX(Hours)
XXXX(Hours)
XXXX(Hours)
XXXX(Minute)
ON/OFF
Power on running time
Fixture running time
Lamp running time
Lamp off time
Clear lamp time
Temperature Info
Base Temperature
Head Temperature
XX /℉
XXX /℉
Software Version
Ver1.0
Temperature
on
the
display board of the base
Temperature in the head
Software version of each
IC
©Elation Professional®
19
Design Wash 575E™
Lamp Control
Design Wash 575E™
Lamp On or Off
Automatic La-On
Lamp On Via DMX
Lamp Off Via DMX
Lamp Off No DMX
Lamp On at Temp.
Lamp Off at Temp.
Personality
Status Settings
Service Setting
Users Mode
Set
Effect Adjust
Reset Function
Fans Control
Display Setting
Temperature
C/F
Initial Effect
Reset Default
Reset All
Reset Pan&Tilt
Reset Colors
Reset Shutter
Reset Others
Test Channel
Manual Control
Calibrate Values
ON/OFF
ON/OFF
ON/OFF
ON/OFF
OFF, 0FF~19M
20~79 ,45 /68~174℉ 113℉
80~139 , 130 /176~282℉, 266℉
Address via DMX
No DMX Status
Pan Reverse
Tilt Reverse
Fine Resolution
Pan Degree
Feedback
Movement Speed
Mic Sensitivity
ON/OFF
Close/Hold/Auto/Music
ON/OFF
ON/OFF
ON/OFF
630/540
ON/OFF
Speed 1~ 4
0~99%
Service Password
Fan Voltage
Auto Fans Speed
High Fans Speed
Low Fans Speed
Shutoff Time
Celsius
Fahrenheit
PAN……
ON/OFF
Password=XXX
High/Low
PAN =XXX
PAN ……
PAN
PAN =XXX
:
:
--Password-Color wheel
Password=XXX
Color wheel=XXX
:
:
User Mode
XXXXXX(Band)
User Mode A
User Mode B
User Mode C
Edit User Mode
PAN
PAN = CH01
:
:
©Elation Professional®
20
Lamp on/off
Lamp on/off when Power
on
Lamp on via DMX
Lamp off via DMX
Lamp off if no DMX
Lamp restart at temp.
Lamp off at temp.
Add. via DMX
Auto run if no DMX
Pan Reverse movement
Tilt Reverse movement
Fine resolution switch
Pan Degree Select
Movement
Feedback
switch
Movement Mode Select
Sensitivity of Mic.
Service Code“=050”
Fan Voltage Select
Fans Speed Mode Select
Display shutoff time
Temperature
switch
between /℉
Initial effect position
Restore factory sett.
Reset all motors
Reset Pan/Tilt
Reset color wheel
Reset
shutter
and/or
dimmer
Reset other motors
Test function
Fine adjustment of the
lamp
Calbrate and adjust the
effects to standard/right
position Password “050”
User’s mode to change
channel numbers
Preset User modes
Design Wash 575E™
Edit Program
Design Wash 575E™
Select
Programs
Auto Pro Part 1
Auto Pro Part 2
Auto Pro Part 3
Program 1 ~ 10
Program 1 ~ 10
Program 1 ~ 10
Edit Program
Program 1
:
Program 10
Edit Scene 001
~ Edit Scene
250
XX~XX
Program Test
Step 01=SCxxx
Step 64=SCxxx
Pan,Tilt,……
--Secne Time-Input By Outside
Edit Scenes
Rec. Controller
Program 1
Program 2
Program 3
(“STEP XX”)
Pan=xxx……
TIME=xx.xs
Select programs to be run
Testing program
Program in loop
Save and exit
Save and automatically
return
manual scenes edit
Automat. scenes rec
8. 1 Function Mode:
1. DMX address setting
After applying power and the rest process the Design Spot 575™ LCD will display the
fixture’s current DMX. If the fixture is not receiving a DMX signal the display will flash
continuously. To set or adjust a DMX address, please follow the procedure below:
1. Toggle through the menu by pressing the Up and Down buttons until the display
shows “Set DMX Address.” Tap the enter button to make changes to the address,.
2. While the current three-digit address is flashing, use the Up and Down buttons to
select adjust the address. Lock your new address into the unit’s memory by
pressing the Enter button.
The DMX address is non-destructible and will remain in the fixture’s memory even
when power to the fixture has been switched off. Memory is backed-up and retained by
an internal power source with a five year shelf life.
2. Display the DMX 512 value of each channel
With this function you can display the DMX 512 value of each channel. The display will
automatically readout the changing DMX values as they are received.
3. Slave setting
With this function, you can define the device as slave for operation in Master/Slave
mode.
©Elation Professional®
21
Design Wash 575E™
Design Wash 575E™
4. Auto Program
This function allows the internal programs to run. The desired program is selected in the
“Select program” section of the control menu. You can set the number of steps under
“Edit program”. You can edit the individual scenes under “Edit scenes”. With this
function, you can run the individual scenes either automatically, i.e. with the adjusted
Step-Time.
5. Music control
With this function, you can run the internal program via sound.
8.2 Information:
1. Time information
Current time
This function displays the running time of the fixture from the last power on. The
display shows “XXXX”, where “XXXX” represents the number of hours the fixture
has been running. This counter is automatically reset after every power-on.
Machine on time
This function tracks the total running time of the fixture from the very first start-up.
Where “XXXX” represents the total number of running hours. This time is none
destructive and will remain in the fixtures memory indefinitely.
Lamp on time
This function tracks the total number of lamp running hours. Where “XXXX”
represents the number of hours the lamp has been running. This counter should be
reset after every lamp change.
Lamp off time
This function displays the running time of the lamp from the last power on. The
display shows “XXXX”, where “XXXX” represents the number of hours the lamp has
been running since it was last struck. This counter is automatically reset after every
©Elation Professional®
22
Design Wash 575E™
Design Wash 575E™
power-on.
Clear lamp time
This function resets the lamp “ON” time to zero. Please reset the lamp “ON” time at
every lamp replacement. This procedure tracks the lamp running time so the lamp
can be replaced at the end of it’s recommended duty cycle.
• Select “Clear lamp time” in the system menu.
• The LCD will display “ON” or “OFF.” Were “ON” will reset the lamp time.
• Press enter to confirm.
• Press the Mode/Esc-button to return to the main menu.
2. Temp. Info.
Base Temp – This function will display the base temperature of the fixture.
Inside head Temp – This function will display the head temperature of the fixture.
3. Software version
This function will display the current operating software version of the fixture.
• Select “Software Version” in the system menu.
• Press enter to confirm.
• The LCD will read “V-X.X”, “X.X” represents the version number, e.g. “V-1.0”,
“V-2.6”.
• Use the UP and DOWN buttons to toggle through the software version of
different IC’s.
• Press the Mode/Esc-button to return to the main menu.
8.3 Lamp Control:
1. Lamp on/off
With this function you can switch the lamp on or off via the Control Board.
• Select "Lamp on/off" by turning the LCD controls.
• Press the LCD controls, the display shows “ON” or “OFF”.
©Elation Professional®
23
Design Wash 575E™
Design Wash 575E™
• Turn the LCD controls to select “ON” if you wish to strike the lamp or “OFF” in order
to switch it off.
• Press the LCD controls to confirm.
• Press the Mode/Esc-button in order to return to the main menu.
2. Lamp on by Power
With this function you can select if the lamp will be switched on when switching the
power on. Select “ON” by turning the LCD controls if you wish to enable this function or
“OFF” if you don’t.
3. Lamp on via external DMX controller
With this function you can select if you can switch the lamp on via an external controller.
Select “ON” by turning the LCD controls if you wish to enable this function or “OFF” if
you don’t.
4. Lamp off via external DMX controller
With this function you can select if you can switch the lamp off via an external controller.
Select “ON” by turning the LCD controls if you wish to enable this function or “OFF” if
you don’t.
5. Lamp Off if no DMX
With this function you can select to switch off the lamp off automatically if there is no
DMX signal). Select “ON” by turning the LCD controls if you wish to enable this function
or “OFF” if you don’t.
6. Lamp on at temp.
With this function you can set the inside temperature from which the projector will
restrike the lamp after automatic lamp shut off.
7. Lamp off at temp.
With this function you can set the inside temperature at which the projector will
automatically switch the lamp off. Turn the LCD controls to select the maximum inside
©Elation Professional®
24
Design Wash 575E™
Design Wash 575E™
temperature between 80° C and 139° C. Inside temperatures below 90° C are not critical.
90° C and more should lead to the lamp being switched off. Please note that the outside
temperature should not exceed 45° C.
8.4 Personality:
1. Status setting
A. Address via DMX - This function allows the DMX address to remotely be
adjusted from a DMX console. This setting requires special settings for both the
controller and the fixture. RDMX is on by default. Follow the procedure listed
below to access the RDMX functions:
Fixture Settings:
1. Access the main menu.
2. Tap the UP button until “Address via DMX” is displayed, press ENTER.
3. Tap the UP button until “RDMX” is displayed, press ENTER.
4. The display will show “ON/OFF.”
5. Press the UP button to display “ON” to activate this function, or “OFF” to
deactivate this function.
6. Press ENTER to confirm.
7. Press MODE/ESC to return to the main menu.
Controller Settings:
1. Set the DMX value of channel 1 to a value of 7.
2. Set the DMX value of channel 2 to a value of 7 or 8. When channel 2 is
set to "7" you can adjust the starting address between 1 and 255. When
set to "8" you can adjust the starting address between 256 and 511.
3. Use channel 3 to set your desired DMX starting address. For example: If
you want to set the starting address to 57, set channel 1 to a value of “7,”
set channel 2 to a value of “7” and use channel 3 to set your address to
57 by selecting a channel value of 57. Example 2: If you want to set the
starting address to 420, set channel 1 to a value of “7,” channel 2 to "8"
and channel 3 to "164" (256+164=420).
©Elation Professional®
25
Design Wash 575E™
Design Wash 575E™
4. Wait for approximately 20 seconds for the unit to complete the
address reset function.
B. No DMX Status – This function dictates how the fixture will function if it
looses DMX signal during normal operation. The default function is set to
hold, in which the fixture will lock into the last DMX signal it received and
remain in that position until it is turned off or begins receiving a new DMX
signal. If the fixture is turned on without any DMX signal, the fixture will
automatically go in to sound-active mode.
Available settings are: “Close” –
Shutter flags will close. “Hold” – Fixture will remain at it’s last settings. “Auto”
– Fixture will go into stand-alone mode, running the built-in program. “Music”
– The fixture will go into sound-active mode.
C. Pan Reverse - This function allows you to invert all pan movements. Use
the Up and Down buttons to turn this function On and Off. Press the Enter
button to accept the change or the Mode button to cancel and return to the
main menu.
D. Tilt Reverse - This function allows you to invert all tilt movements. Use the
Up and Down buttons to turn this function On and Off. Press the Enter
button to accept the change or the Mode button to cancel and return to the
main menu.
E. Fine resolution – This function changes the DMX channel operation from
8bit to 16bit.
F. Pan Degree – This function changes the maximum Pan resolution from
either 540˚ or 630˚. The default function is 540˚.
G. Feedback – This function turns the feedback correction on or off. This
function is set to on as default.
H. Movement Speed – This function changes the order of the DMX channels
©Elation Professional®
26
Design Wash 575E™
Design Wash 575E™
to more closely match similar fixtures from different vendors, thus allowing
the user easier functionality when programming. There are four different
mode variations.
I.
Mic Sensitivity – This function make the internal microphone more or less
sensitive to sound. This function only works in conjunction with the sound
active modes. The default setting is 70% and setting range from 0 % to 99
%.
2. Service Setting
A. Service Password – You must enter this service password, the functions
“Fan Voltage” can be activated and operated. The service password is 050.
B. Fan Voltage– With this function you can select the Fan voltage from either
high or low. The default function is low.
3. Fans Control - This function is used to change the functionality of the internal cooling
fans. The available selections are: 1) “AUTO” – The fans will automatically switch
between low and high speeds depending on the internal operating temperature. 2)
“HIGH” – The fans will run in high-speed mode regardless of operating temperature. 3)
“LOW” – The fans will remain in low speeds regardless of internal operating
temperature.
4. Display Setting – With this function, you can display the shutoff time.
5. Temperature C/F – This function changes the temperature unit readout from either the
temperature Celsius or Fahrenheit.
6. Initial effect - With this function, you can adjust with which value the respective
channels will start.
7. Restore factory settings - With this function you can restore the factory settings of the
device. All settings will be set back to the default values (shaded). Any edited scenes will
be lost.
©Elation Professional®
27
Design Wash 575E™
Design Wash 575E™
8.5 Reset Functions:
1.
Reset All: This function will reset all internal motors to the home position.
2.
Reset Pan and Tilt: This function will only reset the pan and tilt motors to the home
position.
3.
Reset Colors: This function will only reset the color wheel and the CMY filter motors
to the home position.
4.
Reset Shutter: This function will only reset the blackout shutter to the home
position.
5.
Reset Others: This function will reset all other motors to the home position.
8.6 EFFECT Adjust:
9.6.1 Test Channel – This menu function allows the user to select each individual
fixture channel and test it’s function independently from the control board.
9.6.2 Lamp adjustment (manual control) – This function readies the fixture for lamp
optimization in a simple single step procedure. This function will center the pan
and tilt motors while at the same time open the shutter and bring the dimmer to
100%. The pan and tilt function will still operate if the fixture needs to be
positioned to a flat clear surface.
9.6.3 Calibrate values – This function should only be used by a qualified technician.
This function allows a user to make small adjustments to the effect wheels (color,
gobo, shutter, etc) to compensate for ware or in the event a sensor has been
knocked slightly out of place. Because improper use of this function can result in
undesired operation this function has been password protected. The password is
050 and must be entered each time the calibration menu function is entered.
8.7
USER MODE:
8.7.1 User mode – This function allows the user to create user defined channel orders.
This will allow the fixture to match the channel order of other fixtures on the
market for easier operation.
8.7.2 Edit User mode – This function allows the user to make the actual changes in
the user defined modes that are accessed through the previous function.
©Elation Professional®
28
Design Wash 575E™
Design Wash 575E™
8.8
EDIT PROGRAM:
8.8.1 Select program – This function allows the user to select one of ten of the user
defined built-in programs. This program is then accessed in “Function Mode”
under “Program Run.”
8.8.2 Edit program – This function allows the user to edit the built-in programs.
8.8.3 Edit Scenes – This function allows the user to edit or define the actual scenes
that are stored in the user defined built-in programs that are accessed in the
previous step.
8.8.4 Rec Controller - The Design Wash 575E features an integrated DMX recorder
by pre-programmed scenes can be transmitted to the fixture via any standard
DMX controller. This function allows those scenes to be stored in to the fixture’s
built-in memory and then subsequently used to create user defined programs.
9. OPERATION
Operating Modes: The Design Wash 575E™ can operate in three different modes. This
next section will detail the differences in the operating modes.
• Stand-alone mode - The fixture will react to sound, chasing through the built-in programs.
• Master/Slave mode - You can daisy chain up to 16 fixtures together to get a synchronized
light show without the need of an external controller. The fixtures will react to sound chasing
to synchronized light show.
• DMX control mode - This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation® Show Designer 2.
9.1 Universal DMX Control: This function allows you to use a universal DMX-512
controller such as the Elation® Show Designer 2™ or Elation® Show Designer 3™ to
©Elation Professional®
29
Design Wash 575E™
Design Wash 575E™
control head movement, the color wheel, the shutter (strobe), and all other DMX traits.
A DMX controller allows you to create unique programs tailored to your individual
needs. The Design Wash 575E™ uses 24 DMX channels. See page 36 for detailed
description of the DMX traits. To control your fixture in DMX mode, follow the set-up
procedures on pages 16-18 as well as the set-up specifications that are included with
your DMX controller. Use the controller’s faders to control the various DMX fixture traits.
This will allow you to create your own programs.
9.1.1 Follow the instruction on page 24 to set the DMX address.
9.1.1
Be sure to use a terminator on the last fixture, especially for longer cable
runs (more than a 100 feet).
9.1.1 For help operating in DMX mode consult the manual included with your DMX
controller.
9.2 Stand-Alone Operation (Sound Active): This mode allows a single fixture to run to
the beat of the music. Only use this mode when running a single fixture, or when running
several fixtures as individuals.
9.2.1 Mount your fixture in a secure and stable manner.
9.2.1 Access the main menu and select the AUDI function, this will give you access to
the audio submenu. See page 16 for the menu breakdown.
9.2.1 In the audio submenu choose the audio chase speed, fast or slow. Slow (ASLW)
will trigger the chase sequence to every two beats, while fast (AFST) will trigger
the chase impulse every beat. See page 16 for more details.
9.2.1 Be sure the Master (MSTR) function is switched “ON,“ and the SVPT function is
switched “OFF.“
9.2.1 Choose your room size. The size function allows you to choose a the
©Elation Professional®
30
Design Wash 575E™
Design Wash 575E™
approximate size of the room (NORM, BIG, MIDL, SMAL). The built-in programs
will automatically adjust to your selection to optimize light output for your room.
9.2.1 Use the sound sensitivity knob on the side control panel to make the unit more
or less sensitive to sound. Turning the knob in clockwise direction will make the
unit more sensitive to sound, while turning the knob counter-clockwise will make
the unit less sensitive to sound. Note: This unit will react to the low frequencies
of a sound source, tapping on the fixture or high pitched sound may not trigger
the fixture.
9.2 Master-Slave Operation (Sound Active): This function will allow you to link up to
16 fixtures together and operate without a controller. The fixtures will be sound
activated. In Master-Slave operation one fixture will act as the controlling fixture and
the others will react to the controlling fixtures programs. Any fixture can act as a
Master or as a Slave.
9.2.1 Using standard XLR microphone cables, daisy chain your fixtures together via
the XLR connector on the rear of the fixtures. Remember the Male XLR
connector is the input and the Female XLR connector is the output. The first
fixture in the chain (master) will use the female XLR connector only - The last
fixture in the chain will use the male XLR connector only. For longer cable runs
we suggest a terminator at the last fixture.
9.2.2 Follow the same procedures listed in the previous Stand-Alone section. With
two exceptions; Be sure the first unit in the chain is selected as the
“master“(MSTR) is turned on in the audio submenu. All other fixtures must be
in “slave“ mode (SVPT) turned on in the audio submenu.
©Elation Professional®
31
Design Wash 575E™
Design Wash 575E™
10. DMX CHANNEL TRAITS:
The chart below details the channel layout for 16 DMX channels (default).
In 8bit mode the “Pan Fine” and “Tilt Fine” channels are not used, thus converting the fixture
into a 14-channel DMX fixture.
CHANNEL 1: Pan Movement (540˚ or max. 630°User Selectable)
CHANNEL 2: 16bit Pan Movement (pan fine)
CHANNEL 3: Tilt Movement (max. 265°)
CHANNEL 4: 16bit Tilt Movement (tilt fine)
CHANNEL 5: Color Wheel
CHANNEL 6: Cyan Filter
CHANNEL 7: Magenta Filter
CHANNEL 8: Yellow Filter
CHANNEL 9: Effect wheel
CHANNEL 10: Stepless Zoom
CHANNEL 11: Strobe (0-13Hz), and Shutter close/open function + random strobe
CHANNEL 12: Dimmer (Intensity) Control
CHANNEL 13: Color Macros (CMY and Color Wheels)
CHANNEL 14: CMY Speed
CHANNEL 15: Speed Control (Pan/Tilt movement, blackout selection)
CHANNEL 16: Special (Auto program control + lamp on, motor reset, lamp switch off)
©Elation Professional®
32
Design Wash 575E™
Design Wash 575E™
DMX channel function and values:
Channel 1 - PAN movement 8bit :
Channel 2 – Pan fine
Channel 3 - TILT movement 8bit :
Channel 4 – Tilt fine
Channel 5 - Color Wheel 1 :
0-13
Open / white
14-27 Color 1
28-41 Color 2
42-55 Color 3
56-69 Color 4
70-83 Color 5
84-97 Color 6
98-111 Color 7
112-127 Color 8
128-187 Forwards rainbow effect from fast to slow
188-195 No rotation
196-255 Backwards rainbow effect from slow to fast
Channel 6 - Cyan Color Wheel :
0-255 Cyan (0-white, 255-100% Cyan)
Channel 7 - Magenta Color Wheel :
0-255 Magenta (0-white, 255-100% magenta)
Channel 8 - Yellow Color Wheel :
0-255 Yellow (0-white, 255-100% Yellow)
Channel 9 - Effect wheel
0-3
Open / white
4-127 Beam shaper indexing
128-189 Forwards rainbow effect from fast to slow
190-193 No rotation
194-255 Backwards rainbow effect from slow to fast
©Elation Professional®
33
Design Wash 575E™
Design Wash 575E™
Channel 10 – Stepless Zoom
0-255 Zoom adjustment from small to big
Channel 11 - Shutter, strobe
0-31
Shutter closed
32-63 No function (shutter open)
64-95 Strobe effect slow to fast
96-127 No function (shutter open)
128-159 Pulse-effect in sequences
160-191 No function (shutter open)
192-223 Random strobe effect slow to fast
224-255 No function (shutter open)
Channel 12 – Dimmer intensity
0-255 Intensity 0 to 100%
Channel 13 - Color macros - CMY and color wheel
0-7
Off
8-15
Macro1
16-23 Macro2
24-31 Macro3
32-39 Macro4
40-47 Macro5
48-55 Macro6
56-63 Macro7
64-71 Macro8
72-79 Macro9
80-87 Macro10
88-95 Macro11
96-103 Macro12
104-111 Macro13
112-119 Macro14
120-127 Macro15
128-135
136-143
144-151
152-159
160-167
168-175
176-183
184-191
192-199
200-207
208-215
216-223
224-231
232-239
240-247
248-255
Macro16
Macro17
Macro18
Macro19
Macro20
Macro21
Macro22
Macro23
Macro24
Macro25
Macro26
Macro27
Macro28
Macro29
Macro30
Random CMY
Channel 14 - Speed Of CMY And Dimmer :
0-255 Speed Max ->Min
Channel 15 - Speed pan/tilt movement
0-225 max to min speed
226-235 blackout by movement
236-245 blackout by all wheel changing
©Elation Professional®
34
Design Wash 575E™
Design Wash 575E™
246-255 no function
Channel 16 – Lamp on/off, reset, internal programs
0-19
Color change normal
20-39 Color change to any position
40-59 Lamp on
60-79 Lamp switch off
80-84 All motor reset
85-87 Scan motor reset
88-90 Colors motor reset
91-93 No function
94-96 Shutter & Dimmer motor reset
97-99 Other motor reset
100-119 Internal program 1 (scene1~8 of EEPROM)
120-139 Internal program 2 (scene9~16 of EEPROM)
140-159 Internal program 3 (scene17~24 of EEPROM)
160-179 Internal program 4 (scene25~32 of EEPROM)
180-199 Internal program 5 (scene33~40 of EEPROM)
200-219 Internal program 6 (scene41~48 of EEPROM)
220-239 Internal program 7 (scene49~56 of EEPROM)
240-255 Music Control (scene of Program 1)
©Elation Professional®
35
Design Wash 575E™
Design Wash 575E™
11.
FUSE REPLACEMENT
Caution: Always replace with the exact same type fuse, unless otherwise specified by an authorized
Elation® service technician. Replacing with anything other than the specified part can damage your unit
and will void your manufactures warranty.
Warning: If you continue to blow fuses, STOP using the fixture. Contact customer support for further
instructions, you may have to return the unit for servicing. Continuing to use the unit may cause serious
damage.
Fuse Replacement: Locate and remove the unit’s power cord from the main power supply. Once the
cord has been removed located the fuse holders located on the side panel near the power input
connection. Using a flat-head screwdriver unlock the fuse holder from its’ housing by turning the holder in
a counter-clockwise direction. Once the fuse holder has been unlocked, pull back on the fuse holder to
expose the fuse. Gently pull out the bad fuse and discard of it properly and replace it with an exact match.
Reassemble in reverse order.
©Elation Professional®
36
Design Wash 575E™
Design Wash 575E™
12. ERROR CODES:
When power is applied, the unit will automatically enter a “reset/test” mode. This mode
brings all the internal motors to a home position. If there is an internal problem with one or
more of the motors an error code will flash in the display in the form of “XX Er” were as XX
will represent a channel function. For example, when the display shows “Color wheel Er,” it
means there is some type of error with the channel 5 motor. If there are multiple errors
during the start-up process they will all flash in the display. For example: if the fixtures has
errors on channel 5, channel 6, and channel 7 all at the same time, you will see the error
message “Color wheel Er”, “Cyan Er,” and ”Magenta Er” flash repeated 5 times.
If an error does occur during the initial start-up procedure the fixture will self-generate a
second reset signal and try to realign all the motors and correct the errors, if the error persist
after a second attempt a third attempt will be made.
If after a third attempt all the errors have not been corrected the fixture will make the
following determinations: 1) 3 or more errors - The fixture cannot function properly with three
or more errors therefore the fixture will place itself in a stand-by mode until subsequent
repairs can be made. 2) Less than 3 errors - The fixture has less than 3 errors, therefore
most other functions will work properly. The fixture will attempt to operate normally until the
errors can be correct by a technician. The errors in question will remain flashing in the
display as a reminder of internal errors.
Pan Er
(PAN-yoke movement error) This message will appear after the reset of the fixture if the
yoke’s magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the
stepping-motor is defective ( or its driving IC on the main PCB). The PAN- movement is not
located in the default position after the reset.
Tilt Er
(TILT-head movement error) This message will appear after the reset of the fixture if the
head’s magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the
stepping-motor is defective (or its driving IC on the main PCB). The TILT- movement is not
©Elation Professional®
37
Design Wash 575E™
Design Wash 575E™
located in the default position after the reset.
Color wheel Er
(Color wheel- error) This message will appear after the reset of the fixture if the
magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the
stepping-motor is defective ( or its driving IC on the main PCB). The color wheel is not
located in the default position after the reset.
Cyan Color Er
(Cyan Color-wheel error) This message will appear after the reset of the fixture if the
magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the
stepping-motor is defective (or its drive circuit on the main PCB). The Cyan Color wheel is
not located in the default position after the reset.
Magenta Color Er
(Magenta Color-wheel error) This message will appear after the reset of the fixture if the
magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the
stepping-motor is defective (or its drive circuit on the main PCB). The Magenta Color-wheel
is not located in the default position after the reset.
Yellow Color Er
(Yellow Color-wheel error) This message will appear after the reset of the fixture and if the
magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the
stepping-motor is defective (or its driver circuit on the main PCB). The Yellow Color -wheel is
not located in the default position after the reset.
Zoom Er
(Zoom motor error) This message will appear after the reset of the fixture if the
magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the
stepping-motor is defective (or its driving IC on the main PCB). The Stepless Zoom is not
located in the default position after the reset.
©Elation Professional®
38
Design Wash 575E™
Design Wash 575E™
Dimmer Er
(Dimmer wheel error) This message will appear after the reset of the fixture if the
magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the
stepping-motor is defective (or its driving IC on the main PCB). The Dimmer wheel is not
located in the default position after the reset.
©Elation Professional®
39
Design Wash 575E™
Design Wash 575E™
13. CLEANING AND MAINTENANCE
The following points have to be considered during the inspection:
1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may
fall out during normal operation resulting in damage or injury as larger parts could fall.
2. There must not be any deformations on the housing, color lenses, rigging hardware
and rigging points (ceiling, suspension, trussing). Deformations in the housing could
allow for UV radiation leakage. Damaged rigging points or unsecured rigging could
cause the unit to fall and serious injure a person.
3. All mechanical parts and motors should not show any traces of serious wear and
should rotate freely.
4. Electric power supply cables must not show any damage, material fatigue or
sediments. Never remove the ground prong from the power cable.
Further instructions depending on installation and usage have to be adhered by a skilled
installer and any safety problems should be addressed before attempting operation.
We recommend frequent fixture cleaning, this will ensure operational longevity and crisp
light output. When cleaning, please use a moist, lint-free cloth. Never use alcohol or
solvents.
There are no user serviceable parts inside this fixture with the exception of the lamp. Please
refer all other service related issues to an authorized Elation service technician.
Should you decide to service the fixture yourself please order genuine Elation parts directly
from Elation.
©Elation Professional®
40
Design Wash 575E™
Design Wash 575E™
14. 2-YEAR LIMITED WARRANTY
A.
Elation Professional® hereby warrants, to the original purchaser, Elation Professional®
products to be free of manufacturing defects in material and workmanship for a period of two
years, (730 days) from the date of purchase. This warranty shall be valid only if the product
is purchased within the United States of America, including possessions and territories. It is
the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B.
For warranty service, send the product only to the Elation Professional® factory. All
shipping charges must be pre-paid. If the requested repairs or service (including parts
replacement) are within the terms of this warranty, Elation Professional® will pay return
shipping charges only to a designated point within the United States. If the entire instrument
is sent, it must be shipped in its original package. No accessories should be shipped with the
product. If any accessories are shipped with the product, Elation Professional® shall have no
liability what so ever for loss of or damage to any such accessories, nor for the safe return
thereof.
C.
This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which Elation Professional® concludes, after inspection, affects the
reliability of the product; if the product has been repaired or serviced by anyone other than
the Elation Professional® factory unless prior written authorization was issued to purchaser
by Elation Professional®; if the product is damaged because not properly maintained as set
forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, Elation Professional® will replace
defective parts at its expense, and will absorb all expenses for warranty service and repair
labor by reason of defects in material or workmanship.
The sole responsibility of Elation
Professional® under this warranty shall be limited to the repair of the product, or replacement
thereof, including parts, at the sole discretion of Elation Professional®. All products covered
by this warranty were manufactured after January 1, 1990, and bare identifying marks to that
©Elation Professional®
41
Design Wash 575E™
Design Wash 575E™
effect.
E.
Elation Professional® reserves the right to make changes in design and/or
improvements upon its products without any obligation to include these changes in any
products theretofore manufactured.
F.
No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by
applicable law, all implied warranties made by Elation Professional® in connection with this
product, including warranties of merchantability or fitness, are limited in duration to the
warranty period set forth above. And no warranties, whether expressed or implied, including
warranties of merchantability or fitness, shall apply to this product after said period has
expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as
is expressly provided above; and under no circumstances shall Elation Professional® be
liable for any loss or damage, direct or consequential, arising out of the use of, or inability to
use, this product.
G.
This warranty is the only written warranty applicable to Elation Professional® Products
and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
©Elation Professional®
42
Design Wash 575E™
Design Wash 575E™
15.
Photometric Data:
©Elation Professional®
43
Design Wash 575E™
Design Wash 575E™
16.
DIMENSIONAL DRAWINGS:
©Elation Professional®
44
Design Wash 575E™
Design Wash 575E™
17. CIRCUIT SCHEMATIC
©Elation Professional®
45
Design Wash 575E™
Design Wash 575E™
©Elation Professional®
46
Design Wash 575E™
Design Wash 575E™
18. TECHNICAL SPECIFICATIONS
Power supply
Power consumption
Fuse protection
□100VAC, 50Hz; □120VAC, 50Hz; □208VAC, 50Hz;
□220VAC, 50Hz; □230VAC, 50Hz; □240VAC, 50Hz; or
□100VAC, 60Hz; □120VAC, 60Hz; □208VAC, 60Hz;
□220VAC, 60Hz; □230VAC, 60Hz; □240VAC, 60Hz;
120V = 10A/250V, GMA (5x20mm fine-wire fuse)
220V = 5A/250V, GMA (5x20mm fine-wire fuse)
Lamp
Type
Philips Gold MSR575/2 SA DE
Life time
750 Hrs
Color temperature
7200˚ K
Luminous flux
43.000 lm
Optical system
Parabolic dichroic glass reflector
Variable beam angle 13˚ ~ 50˚
Lenses hardened and tempered, anti-reflex coated
Colors
8 dichroic filter plus white, half-color compatible
CMY Color mixing unit
Cyan color filter 0 - 100%
Magenta color filter 0 - 100%
Yellow color filter 0 - 100%
Shutter / Strobe / Dimmer
Strobe effect with variable speed 1 - 10 flashes per second
Continuously mechanical dimmer 0 - 100%
Zoom
Zoom range 13° - 50°
DMX Channels
16 (16bit – default) or 14 (8bit – user selectable)
Drive
Standard DMX-512, 3 pole XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1 or 5 pole XLR; n/a = Pin
5, n/a = Pin 4, [+] = Pin 3, [-] = Pin 2, [Ground] = Pin 1
Starting DMX [001].
Pan / Tilt
Pan - movement
Tilt - movement
Weights and measures
Width of the base
Length of the base
Height (head vertical)
Weight (net)
630° in max. 2.0 seconds, 16 bit resolution
265° in max. 1.5 seconds, 16 bit resolution
42cm (W) x 46cm (L) x 51cm (H) ~ Level vertical
30Kgs / 68Lbs
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.
©Elation Professional®
47
Design Wash 575E™
Elation Professional
6122 S. Eastern Ave.
Los Angeles, CA. 90040
323-582-3322 / 323-832-9142 fax
www.ElationLighting.com /
Info@ElationLighitng.com
Rev. 06/06/2008
Download PDF