Whirlpool | FGP335Y | Specifications | Whirlpool FGP335Y Specifications

Home Appliances
UseAndCare
r
A Note To You
2
Important Safety
Instructions
3
Parts And Features 6
Using Your Range
7
Caring For Your
Range
16
If You Need
Assistance
Or Service
23
Warranty
28
I-800~&ROPER
Call us with questions
STANDARD-CLEANING
GAS RANGE
MODEL FGP335Y
TO THE INSTALLER: PLEASE LEAVE THIS
INSTRUCTION BOOK WITH THE UNIT.
TO THE CONSUMER: PLEASE READ AND
KEEP THIS BOOK FOR FUTURE REFERENCE.
or comments.
\
A Note To You
Thank
you for buying
a Roper@ appliance.
You have purchased a quality, world-class home appliance. Years of engineering experience
have gone into its manufacturing. To ensure that you will enjoy many years of trouble-free
operation, we have developed this Use and Care Guide. It is full of valuable information on
how to operate and maintain your appliance properly and safely. Please read it carefully.
Also, please complete and mail the Ownership Registration Card provided with your appliance. This will help us notify you about any new information on your appliance.
Your
safety
is important
to us.
This guide contains safety symbols and statements. Please pay special attention to these
symbols and follow any instructions given. Here is a brief explanation of the use of each
symbol.
This symbol will help alert you to such
dangers as personal injury burns fire
1 and electrical shock.
’
’ ~~
I
1
u
For further information,
This symbol will help you avoid actions
which could cause product damage
(scratches,
etc.) and damage to
your
personaldents,
property,
1
@ALL RANGES CAN TIP.
*INJURY TO PERSONS
COULD RESULT.
l INSTALL ANTI-TIP
DEVICES PACKED
WITH RANGE.
l SEE INSTALLATION
1 INSTRUCTIONS.
see “The anti-tip bracket” on page 15.
Our toll-free
number,
I-SOO-44-ROPER
available
24 hours a day.
(l-800-447-6737),
is
If you ever have a question concerning your appliance’s operation, or if you need service, first
see “If You Need Assistance Or Service” on page 23. If you need further help, feel free to call
us. When calling, you will need to know your appliance’s complete model number and serial
number. You can find this information on the model and serial number plate (see diagram on
page 6). For your convenience, we have included a handy place below for you to record these
numbers, the purchase date from the sales slip and your dealer’s name and telephone
number. Keep this book and the sales slip together in a safe place for future reference.
Model Number
Dealer Name
Serial Number
Dealer Phone
Purchase
2
Date
Important
READ
Safety Instructions
AND
SAVE
THESE
INSTRUCTIONS
Gas ranges have been thoroughly tested for safe and efficient operation. However, as with
any appliance, there are specific installation and safety precautions which must be followed
to ensure safe and satisfactory operation.
To reduce the risk of fire, electrical shock, injury to persons,
or damage when using the range, follow basic precautions,
including the following:
WARNING: If the information
in this manual is not followed exactly,
a fire or explosion may result causing property damage, personal
injury or death.
Do not store or use gasoline or other flammable
the vicinity of this or any other appliance.
vapors
and liquids
in
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
l
Do not touch any electrical
building.
l
l
do not use any phone in your
Immediately call your gas supplier
the gas supplier’s
instructions.
If you cannot
l
switch;
from a neighbor’s
reach your gas supplier,
phone.
Follow
call the fire department.
Installation
and service must be performed
service agency or the gas supplier.
by a qualified
installer,
General
l
l
Install or locate the range only in accordance with the provided Installation
Instructions. The range must be installed
by a qualified installer. The range must be
properly connected to the proper gas
supply and checked for leaks. The range
must also be properly connected to
electrical supply and grounded.
Gas fuels and their use in appliances can
cause minor exposures to benzene,
formaldehyde, carbon monoxide and
soot, primarily from incomplete combustion. Significant exposure to these
substances can cause cancer or reproductive harm. Properly adjusted burners
l
l
l
with a blue, rather than a yellow, flame will
minimize incomplete combustion. Venting
with a hood or an open window will further
minimize exposure.
Do not store things children might want
above the range. Children could be burned
or injured while climbing on it.
Do not leave children alone or unattended
in area where the range is in use. They
should never be allowed to sit or stand on
any part of the range. They could be
burned or injured.
Do not operate the range if it is damaged
or not working properly.
continued
on next page
3
l
l
l
Do not use the range for warming or
heating the room. Persons could be
burned or injured, or a fire could start.
Do not attempt to light the oven burner
during a power failure. Personal injury
could result. Reset oven controls to the
off position in the event of a power
failure.
Use the range only for its intended use
as described in this manual.
l
l
l
l
l
l
l
Do not touch surface burners, areas
near surface burners or interior surfaces
of oven. Areas near surface burners and
interior surfaces of an oven become hot
enough to cause burns. During and after
use, do not touch, or let clothing or other
flammable materials contact surface
burners, areas near surface burners or
interior surfaces of oven until they have
had sufficient time to cool. Other surfaces of the range, such as the oven
vent opening, the surface near the vent
opening, the cooktop, the oven door and
window, could also become hot enough
to cause burns.
l
When
l
l
l
l
4
Do not wear loose or hanging garments
when using the range. They could ignite
if they touch an open flame and you
could be burned.
Use only dry potholders. Moist or damp
potholders on hot surfaces may result in
burns from steam. Do not let potholder
touch an open flame. Do not use a towel
or bulky cloth for a potholder. It could
catch on fire.
Keep range vents unobstructed.
Do not heat unopened containers. They
could explode. The hot contents could
cause burns and container particles
could cause injury.
Do not store flammable materials on or
near the range. The fumes can create an
explosion and/or fire hazard.
Do not use the oven for storage.
Never use a match or other flame to look
for a gas leak. Explosion and injury could
result.
Know where your main gas shutoff valve
is located.
using
the
cooktop
Make sure the utensils you use are large
enough to contain food and avoid
boilovers and spillovers. Heavy splattering or spillovers left on a range can ignite
and burn you. Pan size is especially
important in deep fat frying.
Check to be sure glass cooking utensils
are safe for use on the range. Only
certain types of glass, glass-ceramic,
ceramic, earthenware or other glazed
utensils are suitable for cooktops without
breaking due to the sudden change in
temperature.
Never leave surface burners unattended
at high heat settings. A boilover could
result and cause smoking and greasy
spillovers that may ignite.
Care
l
l
l
Turn pan handles inward, but not over
other surface burners. This will help
reduce the chance of burns, igniting of
flammable materials, and spills due to
bumping of the pan.
Do not use decorative covers or trivets
over the surface burners.
When
l
l
using
the
l
l
oven
Always position the oven rack(s) in
desired location while oven is cool.
Use care when opening oven door. Let
hot air or steam escape before removing
or replacing food.
l
and
cleaning
Do not clean door heat seal. It is essential
for a good seal. Care should be taken not
to rub, damage or move the seal. Clean
only parts recommended in this Use and
Care Guide.
Do not repair or replace any part of the
range unless specifically recommended in
this manual. All other servicing should be
referred to a qualified technician.
Any additions, changes or conversions
required in order for this appliance to
satisfactorily meet the application needs
must be made by a Roper Distributor or
Qualified Agency.
Disconnect the electrical supply and the
gas supply at the shutoff valve near the
range before servicing the range.
Grease
l
l
Grease is flammable. Do not allow
grease to collect around cooktop or in
vents. Wipe spillovers immediately.
Do not use water on grease fires. Never
pick up a flaming pan. Smother flaming
pan by covering with a well-fitted lid,
cookie sheet or flat tray. Flaming grease
outside of pan can be extinguished with
baking soda or, if available, a multipurpose dry chemical or foam-type extinguisher.
- READ AND SAVE THESE INSTRUCTIONS
-
5
Parts And Features
This section contains captioned illustrations of your range. Use them to become familiar with
the location and appearance of all parts and features.
Clock/
Minute Timer
Manual oven light switch
\
Surface burner
control panel
R
I ‘.-%
Oven vent
Surface burners, grates and
reflector pans
Model and serial
number plate
(under cooktop)
Oven burner
(not shown)
Automatic oven
light switch
Anti-tip
bracket
Broiler drawer
-
Surface ’
burner
markers
Left rear
control
knob
‘Left front
control
knob
&en temperature control
Display
Hour and minute
buttons
6
Cl&k/timer
switch
Rigit rear
control
knob
kight front
control
knob
Using Your Range
In This
Section
Using the surface
burners
Page
Page
. .. .. .. .. . .. .. . .. 7
Adjusting the oven temperature
control . .. . . .. .. .. .. .. . .. .. .. .. . .. .. . .. .. . .. .. .. .. . .. . 13
Broiling . .. . .. .. .. .. .. . .. .. . .. .. .. .. . .. .. . .. .. .. . .. .. . 13
racks and pans .. .. .. .. . .. .. .. 9
Positioning
For best air circulation
.. .. . .. . .. .. .. .. . .. .. 10
Setting the clock .,.............................
11
Using the Minute Timer .. .. . s. .. .. . .. .. .. . . 11
..*..............*..............
Baking/roasting
12
Energy saving tips . .. . .. .. .. . .. .. .. . .. .. . .. .. . 14
The oven vent . . .. .. .. . .. .. .. .. . .. .. . .. .. .. .. . ... 15
The anti-tip
bracket
.. .. .. .. . .. .. . .. .. .. .. . ... 15
To obtain the best cooking results possible, you must operate your range properly. This
section gives you important information for efficient and safe use of your range.
Using
the surface
burners
Your range is equipped with electric ignitors.
Electric ignitors automatically light the
burners each time they are used.
Push in the control knob and turn
counterclockwise
to the LITE position. The
clicking sound is the ignitor sparking.
Visually check that burner has lit.
To stop the clicking sound after the burner
lights, turn the control knob to the desired
setting. You can set the control knob anywhere between HI and LO.
Surface
burner
markers
The solid dot in the surface burner marker
shows which surface burner is turned on by
that knob.
Burner
heat
settings
Use correct burner heat settings (see next
page). If the heat setting is too high, it can:
l Char bacon and cause curling.
l Make eggs tough and crisp at the edges.
l Toughen
liver, fish and seafood
l Scorch
delicate sauces and custards.
l Cause
a boilover.
I
Until you get used to the settings, use
the following as a guide. For best results,
start cooking at the high setting; then turn
the control knob down to continue cooking.
SETTING
LITE
HI
RECOMMENDED
l
l
l
Medium
l
l
l
l
LO
l
USE
To light the burner. After the
burner lights, turn control
back to a desired setting.
l
To start foods cooking.
To bring liquids to a boil.
To hold a rapid boil.
To fry chicken or pancakes.
For gravy, pudding and
icing.
To cook large amounts of
vegetables.
To keep food warm until
ready to serve.
NOTE: Do not cook with the control in the
LITE position.
In case of a prolonged
failure
Surface
Hold a
control
burner
desired
l
power
burners can be manually lighted.
lit match near a burner and turn the
knob to the LITE position. After the
lights, turn the control knob to the
setting.
l
Burn, Fire and Explosion Hazard
Burner flame should not extend
beyond the edge of the cooking
utensil. The flame could burn you and
cause poor cooking results.
Be sure all control knobs are turned to
OFF when you are not cooking.
Someone could be burned or a fire
could start if a burner is accidentally
left ON.
If the flame should go out while
cooking, or if there is a strong gas
odor, turn the burners OFF. Wait five
minutes for the gas odor to disappear
before relighting burner. If gas odor is
still present, see safety note on page
3. Failure to follow these precautions
could result in explosion or fire.
Product
Damage Hazard
Do not leave an empty utensil, or one
which has boiled dry, on a hot surface
burner.
The utensil could overheat and could
damage the utensil or cooking product.
Cookware
tips
No one brand of cookware is best for all
people. Knowing something about pan
materials and construction will help you
select the correct cookware for your needs.
l NOTE:
For best results and greater fuel
efficiency, use only flat-bottomed cookware in good condition.
l The pan should
have straight sides and a
tight-fitting lid.
l Choose
medium to heavy gauge (thickness) pans that are fairly lightweight.
l The pan material
(metal or glass) affects
how fast heat transfers from the surface
burners through the pan material and how
evenly heat spreads over the pan bottom.
Choose pans that provide the best cooking
results.
l
l
l
l
Handles should be made of a sturdy, heatresistant material and be securely attached
to the pan.
Pans should be easy to clean. Check to be
sure there are no crevices, rough edges or
areas where food might collect.
Be sure pans do not tip, whether they are
full or empty.
Use cookware only as it was intended to
be used. Follow pan instructions. This is
very important for glass cookware because
some should be used only in the oven.
Other pans are’marked as flameware and
may be used on the surface burners.
Positioning
racks
for specific
FOOD
Frozen pies, large
roasts, turkeys
Angel
most
yeast
roles,
foods:
RACK POSITION
1st or 2nd rack
guide from bottom
and bundt cakes, 2nd rack guide
quick breads,
from bottom
breads, cassemeats
Cookies, biscuits,
muffins, cakes,
nonfrozen pies
canning
information
The large diameter of most water-bath or
pressure canners combined with high heat
settings for long periods of time can cause
damage to the cooktop.
To protect your range:
l For best results,
use a canner which can
be centered over the surface burner.
l Do not place
canner on two surface
burners at the same time. Too much heat
will build up and will damage the cooktop.
l Start with
hot water. This reduces the
time the control is set on high. Reduce
heat setting to lowest position needed to
keep water boiling.
l Keep reflector
pans clean for best heat
reflection.
and pans
For baking/roasting
with one rack, place
the rack so the top of the food will be
centered in the oven.
Rack placement
Home
2nd or 3rd rack
guide from bottom
When baking on two racks, arrange racks
on first and third rack guides from bottom.
Personal
Injury Hazard
*Always position oven rack(s) in
desired location before turning oven
on. Be sure the rack(s) is level.
l If rack(s) must be moved while oven
is hot, use potholders or oven mitts to
protect hands.
l Do not place items on the open oven
door.
l Be careful when installing
and removing large food items from sixth rack
position. Food will be close to hot
surfaces, including oven bottom and
sides.
Failure to follow the above precautions
could result in personal injury.
6th oven
(roasting
rack position
rack)
When roasting food too larqe to be placed in
oven with rack in lowest position, place rack
on bottom of oven.
For proper roasting, follow these
guidelines:
l The rack must be level
l Use adequate
amount of liquid (meat
juices or water) so food does not get
overdone.
l Do not try to pull
rack out over door.
Rack will be at the same level as door
when door is opened.
For best air circulation
Hot air must circulate around the pans in the
oven for even heat to reach all parts of the
oven. This results in better baking.
l Place the pans so that one is not directly
over the other.
l For best results,
allow 1 l/2-2 inches
(4-5 cm) of space around each pan and
between pans and oven walls. There must
be a minimum space of 1 inch (2.5 cm).
l Use only one cookie sheet in the oven at
one time.
Use the following as a guide to determine
where to place the pans:
One pan
Place in the center of the oven rack.
Two pans
Place in opposite corners of the oven rack.
Three or four pans
Place in opposite corners on each oven rack.
Stagger pans so no pan is directly over
another.
10
\
6th oven rack position
Setting
the clock
When the range is first plugged in, or
following a power outage, “12:OO” will flash
on the display.
1. Slide the ClockITimer
CLOCK position.
CLOCK
0
l:-I
Switch to the
a
TIMER
HOUR
2. Push in and hold the Hour button until
the correct hour appears on the display.
(The numbers wiil only count forward.)
3. Push in and hold the Minute button until
the correct minutes appear on the display.
MINUTE
Using
the Minute
Timer
The Minute Timer does not start or stop the
oven. It works like a kitchen timer. Set it in
minutes up to 1 hour, 59 minutes. The control
will beep when the set time is up.
CLOCK
1. Slide the Clock/Timer switch to the TIMER
position. The display will show “059”
(59 minutes).
TIMER
2. To set a time more than 59 minutes,
push in and release the Hour button. The
display will show “159”. The time can now
be adjusted down by pushing in and holding
the Minute button until the correct time
shows on the display.
MINUTE
To set a time less than 59 minutes, push
in and hold the Minute button until the
correct time shows on the display.
The Minute Timer will automatically start
when the Minute button is released.
3. When the set time has passed, the
display will show “0:OO” and the control will
beep continuously. Slide the Clock/Timer
Switch to the CLOCK position to cancel the
Minute Timer and return to the clock mode.
CLOCK
TIMER
11
Baking/roasting
NOTE: Do not attempt to light the oven
burner during a power failure. See “Important
Safety Instructions” on page 4 for more
information.
1. Position the rack(s) properly before
turning on the oven. To change rack
position, lift rack at front and pull out. For
further information, see “Positioning racks
and pans” on page 9.
2. Push in and turn the Oven Temperature
Control counterclockwise
to the baking/
roasting temperature you want. The oven
burner will automatically light in 50-60
seconds.
3. When baking, preheat the oven for 10
minutes. Put food in the oven.
NOTES:
l
l
Do not preheat when roasting or
cooking items such as casseroles
Do not place food directly on the oven
bottom.
4. During baking/roasting,
the oven burner
will turn on and off to maintain the temperature setting.
5. When baking/roasting
is done, turn the
Oven Temperature Control clockwise to
OFF.
12
Adjusting
the oven temperature
control
Oven temperature controls will gradually
shift after years of use. So, even though
your new oven is properly adjusted to
provide accurate temperatures, it may cook
faster or slower than your old oven.
If, after using the oven for a period of time,
you are not satisfied with the temperature
settings, you can adjust them by following
these steps:
1. Make sure the Oven Temperature
Control Knob is turned to the off position.
Pull knob straight off and flip it over.
2. Loosen the locking screws inside the
control knob. Note the position of the
notches.
3. To lower the temperature, hold knob
handle firmly and move the tooth a notch
clockwise. Each notch equals about
20°F (11°C).
4. To raise the temperature, hold knob
handle firmly and move the tooth a notch
counterclockwise.
Each notch equals
about 20°F (11%).
5. Tighten the locking screws and replace
the control knob.
Broiling
The broiler drawer is located below the oven
door. Always broil with the oven door
closed.
1. Pull the broiler drawer open and tilt the
door panel down.
2. Place broiler pan grid so grease can
drain down ribbing and through slots into
lower part of the broiler pan. See picture.
3. Before the broiler is turned on, place
food on broiler pan and position the
broiler pan at one of the three levels.
4. Close broiler drawer.
To lower
5. Push in and turn the Oven Temperature
Control counterclockwise
to BROIL.
The broiler will automatically light in
50-60 seconds.
6. When broiling is done, turn the Oven
Temperature Control clockwise to OFF.
NOTE: Do not preheat the broiler before
using. Completely close the broiler drawer
during broiling.
Energy
saving
tips
Although the energy used for cooking is
usually a very small percentage of the total
energy used in the home, cooking energy
can be used efficiently. Here are some tips
to help you save energy when using your
cooking product:
l Use pans with flat bottoms,
straight sides
and tight-fitting lids.
l Cook with a minimum
of liquid or fat to
help shorten cooking time.
l Preheat
pans only when recommended
and for the shortest time possible.
l
Start food on higher heat settings, then
set surface burner control on low to
finish cooking.
l
Use the more efficient surface burners
instead of the oven when possible.
l Turn
on the surface burner only after
placing filled pan on the burner grate.
14
l
l
l
l
l
l
“Oven peeking” may cause heat loss,
longer cooking times and unsatisfactory
baking results. Rely on your timer to keep
track of the cooking time.
Bake cakes, pies or cookies when oven is
warm. Best time to bake is right after a
meal has been cooked in oven.
Preheat the oven no longer than necessary.
Plan your meals for the most efficient use
of the range. When using the oven to cook
one food, try to cook the rest of the meal in
it also.
Do not preheat when broiling, roasting or
cooking items such as casseroles.
Keep reflector pans clean for best heat
reflection.
The oven vent
Hot air and moisture escape from the oven
through a vent located in lower part of
backguard. The vent is needed for air
circulation. Do not block the vent. Poor
baking/roasting will result.
NOTE: Never store plastics, paper or other
items that could melt or burn near the oven
vent, or any of the surface burners.
Burn Hazard
When the oven is ON, pans and pan
handles left near the oven vent could
become hot enough to burn the user
and to melt plastics. Use potholders to
move pans.
The anti-tip
bracket
The range will not tip during normal use. However, tipping can occur if you apply too much
force or weight to the open door without the anti-tip bracket properly secured.
Personal
Injury Hazard
*To reduce risk of range tipping over, secure range with a properly
installed anti-tip bracket supplied with range.
l If range is moved for cleaning
or service, check that anti-tip device
is engaged before using range.
Failure to follow the above precautions could result in personal injury.
To verify the anti-tip
is engaged:
l
l
bracket
Grasp rear of range and carefully try to tilt
forward. If anti-tip bracket is attached to
floor with screws and rear leveling legs are
positioned under bracket, range should not
tilt forward.
See Installation Instructions for further
details.
15
Caring For Your Range
In This
Section
Page
Surface burner grates and reflector
pans ..................................................
.16
Lift-up cooktop
................................
.17
Surface burners
...............................
.17
Removing
burner
grates
1. Make sure all surface burners are off and
the surrounding parts are cool.
2. Lift off the surface burner grates and
remove the reflector pans.
3. Wash the grates and reflector pans with
warm, soapy water or in a dishwasher.
Use a nonabrasive, plastic scrubbing pad
for cooked-on foods. Rinse and dry well.
4. Replace reflector pans and burner
grates.
16
the oven bottom
Page
............ .19
chart ...................................
20
The oven light ...................................
22
Cleaning
the oven door ................ .18
Your range is designed for ease of care.
You can do most cleaning with items found
around your home. Cleaning your range
whenever spills or soiling occurs will help to
keep it looking and operating like new.
Surface
Removing
Burn, Electrical Shock, Fire and
Explosion Hazard
l Make sure all controls
are OFF and the
range is cool before cleaning.
l Do not use oven cleaners,
bleach or
rust removers.
l Do not obstruct
the flow of combustion
and ventilation air.
l Keep appliance
area clear and free of
combustible materials, gasoline and
other flammable vapors and liquids.
Failure to follow these guidelines could
result in burns, electrical shock, fire or
explosion.
and reflector
pans
Lift-up
cooktop
1. Remove surface burner grates and reflector
pans.
2. Lift front of cooktop at both front corners until
the support rods lock into place.
-
.
I
Personal Injury Hazard
Be sure both support rods are fully
extended and in the locked position.
Failure to do so could result in personal injury from the cooktop accidentally falling.
Product Damage Hazard
Do not drop the cooktop.
Damage could result to the porcelain
and the cooktop frame.
3. Wipe with warm, soapy water. Use a soapy
steel-wool pad on heavily soiled areas.
4. To lower the cooktop, lift cooktop from both
sides while pressing the support rods back to
unlock them. Lower the cooktop into place.
Replace reflector pans and surface burner
grates.
Surface
burners
1. Lift up the cooktop, following the instructions
above.
2. Before cleaning, remove screws that
hold each of the burners in place. The
screws prevent the burners from moving
during shipment. Remove the shipping
screw with a Phillips screwdriver, lift the
burner up, tilt it to one side at the end
closest to the ignitor and move it toward
the back of the range. This separates the
burner from the gas valve at the front of
the range, so it can be easily removed.
3. Wipe off surface burners with warm, soapy
water and a sponge after each use. To
remove cooked-on food, soak the burners
in a vinegar and water solution for 20-30
minutes. Scrub with a plastic scrubbing pad.
17
4. If ports are clogged, clean with a straight
pin. DO NOT enlarge or distort the ports.
DO NOT use a toothpick to clean the ports.
5. Before putting the burners back, dry
them thoroughly by setting them in a
warm oven for 30 minutes.
6. Replace burners, making sure they are
properly seated and level. Replace
screws.
7. Occasionally
check the burner flames
for proper size and shape as shown. A
good flame is blue in color. If flames lift
off ports, are yellow, or are noisy when
turned off, you may need to clean the
burners (see above), or call a qualified
technician for adjustment.
Typical
Removing
the oven door
Removing the oven door will help make it
easier to clean the oven.
Burn and Electrical Shock Hazard
Make sure all controls are OFF and the
oven is cool before removing oven
door.
Failure to do so could result in burns or
electrical shock.
To remove:
1. Open the door as far as it will go.
2. Remove the screws on each side of the
oven door.
3. Close the door about %I of the way.
4. Lift the door up and off the hinges.
To replace:
1. Be sure the hinge arms are in the open
position. Be careful if pulling the hinges
open by hand. Hinges may snap back
against the oven frame and could pinch
fingers.
18
surface burner flame
at highest setting
2. Hold the door at the sides near the top.
Insert hinge arms into slots at the bottom
of the door. Insert arms evenly, as far as
they will go.
3. If the door is not in line with the oven
frame, remove it and repeat the above
steps.
4. Replace the screws on the oven door.
Removing
the oven bottom
The panel in the oven bottom can be
removed for cleaning.
Burn Hazard
Make sure all parts are cool before
removing.
Failure to do so could result in burns.
To remove:
1. Remove oven racks.
2. Remove the two hold-down screws at the
rear of the oven. If screws are too tight to
remove by hand, use a screwdriver.
3. Place fingers in slots in bottom panel and
lift rear of panel up and back until lip at
the front of panel is clear of front frame of
oven cavity.
4. Lift bottom up and out.
To replace:
1. Place oven bottom panel in oven with the
back raised about 6 inches or until you
can insert the hold-down lip at front of
panel under the front frame of oven
cavity.
2. Push back of oven bottom panel down
fully into place on metal flanges on rear
wall and insert the hold-down screws.
19
Cleaning
chart
Use the following table to help you clean all parts of your range.
PART
Control
knobs
HOW TO CLEAN
WHAT TO USE
Sponge and warm, soapy
water
l
l
l
l
Control
20
panels
Sponge and warm, soapy
water
OR
Paper towel and spray
glass cleaner
Exterior surfaces
(other than control
panels)
Sponge and warm, soapy
water
Surface burner
grates and
chrome reflector
pans
Warm, soapy water and a
nonabrasive, plastic
scrubbing pad
OR
Dishwasher
l
l
l
Turn knobs to OFF and pull straight
away from control panel.
Wash, rinse and dry thoroughly. Do
not soak.
Do not use steel wool or abrasive
cleansers. They may damage the
finish of the knobs.
Replace knobs. Make sure all knobs
point to OFF.
Wash, rinse and dry thoroughly.
Do not use steel wool or abrasive
cleansers. They may damage the
finish.
Do not spray cleaner directly on panel.
Apply cleaner to paper towel.
Wash, rinse and dry thoroughly.
Use nonabrasive, plastic scrubbing
pad on heavily soiled areas.
l
Do not use abrasive or harsh
cleansers. They may damage the
finish.
NOTE: Do not allow foods containing
acids (such as vinegar, tomato or lemon
juice) to remain on surface. Acids may
remove the glossy finish. Also wipe up
milk or egg spills when cooktop is cool.
l
l
l
l
l
In dishwasher, wash with other cooking
utensils.
Dry completely.
Do not use abrasive or harsh
cleansers.
PART
Surface burners
Sponge and warm,
soapy water
Warm, soapy water
and a nonabrasive,
plastic scrubbing pad
OR
Vinegar and water
solution
Broiler drawer,
pan and grid (clean
after each use)
Steel-wool pad and
warm, soapy water
Oven racks
Steel-wool pad and
warm, soapy water
Oven door glass
Paper towel and spray
glass cleaner
OR
Warm, soapy water and
a nonabrasive, plastic
scrubbing pad
Oven cavity
HOW TO CLEAN
WHAT TO USE
Lift up the cooktop. (See page 17.)
Wipe off spills immediately after burner
has cooled.
For cooked-on food:
l Remove
burner from manifold with
Phillips screwdriver.
l Wash with warm, soapy water and a
plastic scrubbing pad or soak in vinegar
and water solution.
l Rinse and dry well.
l If ports are clogged,
clean with a straight
pin. Do not enlarge or distort ports. Do
not use a wooden toothpick.
l Do not clean surface
burner in dishwasher.
l
l
Clean after each use.
Wash, rinse and dry thoroughly.
After broiler is cool, wipe interior with
warm, damp sponge. For heavily soiled
areas, use a soapy steel-wool pad.
l
l
l
Sponge and warm,
soapy water
Wash, rinse and dry thoroughly.
l
l
l
l
l
l
l
Soapy steel-wool pad
for heavily soiled areas
OR
Commercial oven
cleaner for heavily
soiled areas
l
l
l
l
l
Make sure oven is cool.
Follow directions provided with the
cleaner.
Wash, rinse and dry thoroughly.
Make sure oven is cool.
Remove door and oven bottom for
easier access. (See pages 18 and 19.)
Wash, rinse and dry well.
Remove door for easier access.
Rinse well with water.
Remove door and oven bottom for
easier access.
Place newspaper on floor to protect floor
surface.
Follow directions provided with the oven
cleaner.
l
l
Rinse well with clear water.
Use in well-ventilated room.
continued on next page
21
Oven cavity
(continued)
l
The oven light
The oven light will come on when you open
the oven door. To turn on the light without
opening the oven door, use the Oven Light
Switch on the control panel.
Electrical
Shock and Burn Hazard
Make sure oven and light bulb are cool
and power to the range has been
turned OFF before replacing the light
bulb.
Failure to do so could result in electrical shock or burns.
To replace
the oven
light:
1. Unplug appliance or disconnect
power supply.
at main
2. Remove the light bulb from its socket.
Replace the bulb with a 40-watt appliance bulb.
3. Plug in appliance or reconnect
main power supply.
22
HOW TO CLEAN
WHAT TO USE
PART
at the
Do not allow commercial oven cleaners to contact the heat seal, thermostat or exterior surfaces of the range.
Damage will occur.
If You Need Assistance
Or Service
This section is designed to help you save the cost of a service call. Part 1 of this section
outlines possible problems, their causes, and actions you can take to solve each problem.
Parts 2 and 3 tell you what to do if you still need assistance or service. When calling our tollfree telephone number for help or calling for service, please provide a detailed description of
the problem, your appliance’s complete model and serial numbers and the purchase date.
(See page 2.) This information will help us respond properly to your request.
1. Before
calling
for assistance
...
Performance problems often result from little things you can find and fix without tools of any
kind. Please check the chart below for problems you can fix. It could save you the cost of a
service call.
PROBLEM
POSSIBLE
CAUSE
SOLUTION
The power cord is not
plugged into a live circuit
with proper voltage.
Plug the power cord into a live circuit
with proper voltage. (See Installation
Instructions.)
Range is not properly connetted to gas supply.
Contact an authorized Roper service
technician to reconnect range to
gas supply. (See Installation Instructions.)
A household fuse has blown
or a circuit breaker has
tripped.
Replace household fuse or reset circuit
breaker.
Controls are not set correctly.
Reset controls, if needed.
The flow of combustion and/
or ventilation air to the range
is blocked.
Remove blockage to airflow to and
around range.
The oven will
not operate
The Oven Temperature
Control is not turned to a
temperature setting.
Push in and turn the Oven Temperature
Control to a temperature setting.
Burner fails to
light
The power cord is not
plugged into a live circuit
with proper voltage.
Plug the power cord into a live circuit
with proper voltage. (See Installation
Instructions.)
A household fuse has blown
or a circuit breaker has
tripped.
Replace household fuse or reset circuit
breaker. In case of prolonged power
failure, manually light burners (see
we 8).
Burner ports are clogged.
Clean with a straight pin (see pages 18
and 21).
Burner ports are clogged.
Clean with a straight pin (see pages 18
and 21). If this fails, call an authorized
Roper service technician for service.
Nothing
operate
will
Burner flames
are uneven
continued
on next page
23
PROBLEM
POSSIBLE
SOLUTION
CAUSE
Burner flames
Air/gas mixture is incorrect.
lift off ports, are
yellow, or are
noisy when
turned off
Contact an authorized Roper
service technician to check air/gas
mixture.
Burner makes
popping noise
when on
Burner is wet from washing.
Let dry.
Control knob(s)
will not turn
You are not pushing in before
turning.
Push control knob(s) in before turning
to a setting.
Cooking results
are not what
you expected
The range is not level.
Level range. (See Installation
Instructions.)
24
The oven temperature
too low or too high.
seems
Adjust the oven temperature control.
(See “Adjusting the oven temperature
control” on page 13.)
The oven was not preheated
as the recipe calls for.
Preheat oven if called for in recipe.
The recipe has never been
tested or is not from a reliable
source.
Use only tested recipes from a reliable
source.
The pans are not the type or
size recommended in the
recipe.
Refer to a reliable cookbook for recommended pan type and size.
There is not proper air circulation around pan when
baking.
Allow 1% to 2 inches (4-5 cm) on all
sides of the pans for air circulation.
There must be a minimum space of
1 inch (2.5 cm).
Flame size does not fit the
cooking utensil being used.
Adjust flame size to fit cooking utensil.
When broiling, you have not
completely closed the broiler
drawer.
Completely close broiler drawer.
2. If you need
assistance
...
Call our toll-free telephone number. Dial
toll-free from anywhere in the U.S.A.:
l-800-44-ROPER
(l-800-447-6737)
and talk with one of our trained consultants.
The consultant can instruct you in how to
obtain satisfactory operation from your
appliance or, if service is necessary, recommend a qualified service company in your
area.
For further information, write to:
Mr. William Clark
Consumer Assistance Representative
Roper Brand Appliances
2000 M-63
Benton Harbor, MI 49022
Please include a daytime phone number in
your correspondence.
3. If you need
service
4. If you need FSP@ replacement parts . . .
FSP is a registered trademark of Whirlpool
Corporation for quality parts. Look for this
symbol of quality whenever you need a
replacement part for your Roper@ appliance.
FSP replacement parts will fit right and work
right, because they are made to the same
exacting specifications used to build every
new Roper appliance.
To locate FSP replacement parts in your
area, refer to Step 3 above or call our tollfree telephone number in Step 2.
5. If you are not satisfied
how the problem
was
solved . . .
l
...
Contact the dealer from whom you purchased the appliance or the authorized
servicer in your area. For help finding an
authorized servicer in your area, call our
toll-free telephone number in Step 2.
l
l
with
Contact the Major Appliance Consumer
Action Panel (MACAP). MACAP is a group
of independent consumer experts that
voices consumer views at the highest
levels of the major appliance industry.
Contact MACAP only when the dealer,
authorized servicer and Roper Brand
Appliance warrantor have failed to resolve
your problem.
Major Appliance Consumer Action Panel
20 North Wacker Drive
Chicago, IL 60606
MACAP will in turn inform us of your
action.
25
ROPER”
Gas Range
Warranty
LENGTH OF WARRANTY
FULL ONE-YEAR
WARRANTY
(from date of purchase)
1 WE WILL PAY FOR
FSP@ replacement parts and repair labor to correct
defects in materials or workmanship. Service must be
provided by an authorized Roper service company.
WE WILL NOT PAY FOR
A. Service calls to:
1. Correct the installation
of your range.
2. Instruct you how to use your range.
3. Replace house fuses or correct house wiring or plumbing.
4. Replace owner accessible light bulbs.
B. Repairs when your range is used in other than normal, single-family
household
use.
C. Pickup and delivery. Your range is designed to be repaired in the home.
D. Damage to your range caused by accident, misuse, fire, flood, acts of God, or use of
products not approved by us.
E. Repairs to parts or systems caused by unauthorized
appliance.
modifications
made to the
5193
This Roper appliance is warranted by Whirlpool Corporation. Under no circumstances shall it
be liable under this warranty for incidental or consequential damages and all implied warranties are limited to the same time period stated in the express warranties for Roper Brand
Appliances. Some states do not allow the exclusion or limitation of incidental or consequential
damages, or limitation of implied warranties, so these limitations or exclusions may not apply
to you.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
Outside the United States, a different warranty may also apply. For details, please contact
your authorized Roper distributor or military exchange.
If you need service, first see the “Assistance or Service” section of this book. After checking
“Assistance or Service,” additional help can be found by calling our toll-free telephone number,l-800-44-ROPER
(l-800-447-6737),
from anywhere in the U.S.A.
PrInted on recycled paper10% post cO”s”mer
waste
50% recovered malerials
PART NO. 316000726/4372198
0 1993 WhIrlpool
Corporation
@ Rqslered
Trademark
of Whirlpool
Corporation
Printed
in U S.A
Caring For Your Range
In This
Section
Surface units and reflector
Lift-up
cooktop
Removing
Page
bowls . ..27
. . .. .. . .. .. .. . .. . .. .. .. . .. .. .. . ..29
oven door brackets
Page
Cleaning
The oven light .. .. .. . .. .. .. . .. .. . .. . .. .. .. .. .. . .. 32
. . .. . .. .29
Your range is designed for ease of care. You
can do most cleaning with items found
around your home. Cleaning your range
whenever spills or soiling occurs will help to
keep it looking and operating like new.
I
Surface
units
chart . .. .. .. . .. .. .. . .. . .. .. . .. .. .. .. . .. .30
Burn and Electrical Shock Hazard
Make sure all controls are OFF and the
range is cool before cleaning.
Failure to do so can result in burns or
electrical shock.
and reflector
I
bowls
Removing
1. Make sure all surface units are off and
cool before removing surface units and
reflector bowls.
2. Lift the edge of the unit, opposite the
receptacle, just enough to clear the
reflector bowl.
3. Pull the surface unit straight away from the
receptacle.
27
4. Lift out the reflector bowl. See ‘Cleaning
chart” on page 31 for cleaning instructions.
Replacing
1. Make sure all surface units are off before
replacing surface units and reflector
bowls.
2. Line up openings in the reflector bowl
with the surface unit receptacle.
3. Hold the surface unit as level as possible
with the terminal just started into the
receptacle. Push the surface unit terminal
into the receptacle.
4. When terminal is pushed into the receptacle
as far as it will go, push down the edge of
the surface unit opposite the receptacle.
Make sure surface unit is properly positioned and level.
NOTE: Reflector bowls reflect heat back to the
utensils on the surface units. They also help
catch spills. When they are kept clean, they
reflect heat better and look new longer.
If a reflector bowl gets discolored, some of
your utensils may not be flat enough, or some
may be too large for the surface unit. In either
case, some of the heat that’s meant to go into
or around a utensil goes down and heats the
reflector bowl. This extra heat can discolor it.
28
Cleaning
chart
Use the following table to help you clean your range.
PART
Control
knobs
HOW TO CLEAN
WHAT TO USE
Sponge and warm,
soapy water
l
l
l
Control
panel
Sponge and warm,
soapy water
OR
Paper towel and sPraY
glass cleaner
Exterior surfaces
(other than control
panel)
Sponge and warm,
soapy water
Stainless steel
cooktop surface
Sponge and warm,
soapy water
Water and mild
scouring powder
Stainless steel or
steel-wool sponge,
scouring powder and
water
30
l
l
Turn knobs to OFF and pull straight away
from control panel.
Wash, rinse and dry thoroughly. Do not
soak. Do not use steel wool or abrasive
cleansers. They may damage the finish
of the knobs.
Replace knobs. Make sure all knobs point
to OFF.
Wash, rinse and dry thoroughly. Do not
use steel wool or abrasive cleansers.
They may damage the finish.
Do not spray cleaner directly on panel.
Apply cleaner to paper towel.
Wash, rinse and dry thoroughly. Use
nonabrasive, plastic scrubbing pad on
heavily soiled areas.
l Do not use abrasive
or harsh cleansers,
They may damage the finish.
NOTE: Do not allow foods containing acids
(such as vinegar, tomato or lemon juice) to
remain on surface. Acids may remove the
glossy finish. Also wipe up milk or egg spills
when cooktop is cool.
l
l
l
l
Wash, rinse and dry thoroughly to
remove small stains and streaks.
Use a paste made of water and a mild
scouring powder on heavily soiled areas.
Be sure to rub in the direction of the
polish lines on the stainless steel to
preserve the finish.
Small dark spots may occur on your
stainless steel range cooktop. This is
caused by heat oxidation of the steel, and
is in no way harmful. To prevent spots,
never use more heat than is necessary.
To remove spots, scour vigorously with
a stainless steel or steel-wool sponge
and a paste made of scouring powder
and water. Rub in the direction of the
polish lines.
Lift-up
cooktop
1. Lift front of cooktop at the center and
swing the support rod up.
2. Carefully lower the cooktop onto the
support rod. Be sure the tip of the rod fits
securely in the cooktop.
Personal
Injury Hazard
Be sure the rod is held securely. The
cooktop could accidentally fall and
injure you.
I
Product Damage Hazard
Do not drop the cooktop. Damage can
result to the porcelain and the cooktop
frame.
3. Wipe with a sponge and warm, soapy
water. Use a soapy steel-wool pad on
heavily soiled areas.
4. To lower cooktop,
lift cooktop at the
center and swing support rod back and
down into the storage position. Lower the
cooktop.
Removing
oven door brackets
Your range has been shipped with two (2)
oven door retainer brackets. These brackets
do not have to be removed unless you want
to remove the oven door.
To remove
brackets:
1. Open oven door.
2. Remove the screw located at the top of
the bracket just above each door hinge.
(See illustration.)
Screw -
3. Remove brackets.
/
4. Replace screws in existing holes.
-
29
r
PART
HOW TO CLEAN
WHAT TO USE
NOTES:
Certain foods and seasonings containing
salt may in time cause stainless steel to
pit.
l You should wash all foods from your
stainless steel cooktop as soon as
possible.
l When cleaning
stainless steel with a
cleaner, use a cleaner specially designed
for stainless steel.
Stainless steel
cooktop surface
(continued)
Surface
units
l
No cleaning required
l
l
Chrome
bowls
reflector
Warm, soapy water
and a nonabrasive,
plastic scrubbing pad
l
l
l
l
Broiler pan and
grid (clean after
each use)
Steel-wool pad and
warm, soapy water
Oven racks
Steel-wool pad and
warm, soapy water
OR
The Self-Cleaning
cycle
Oven door glass
Oven cavity
Paper towel and spray
glass cleaner
OR
Warm, soapy water
and a nonabrasive,
plastic scrubbing pad
Self-Cleaning
cycle
l
l
Spatters or spills will burn off.
Do not immerse in water.
Wash, rinse and dry thoroughly.
Clean frequently.
Do not use abrasive or harsh cleansers.
Do not clean in Self-Cleaning
oven.
Wash, rinse and dry thoroughly.
Clean in Self-Cleaning cycle.
Wash, rinse and dry thoroughly.
OR
l Leave in oven during
Self-Cleaning cycle.
NOTE: Racks will permanently discolor and
become harder to slide if left in oven during
Self-Cleaning cycle. Apply a small amount
of vegetable oil to the side rungs to aid
sliding.
l
l
l
l
l
Make sure oven is cool.
Follow directions provided with the
cleaner.
Wash, rinse and dry thoroughly.
See “Using The Self-Cleaning
pages 23-26.
Cycle” on
31
The oven
light
- The oven light will come on when you open
the oven door. To turn the light on when the
oven door is closed, use the Oven Light
Switch on the control panel.
Electrical Shock and
Personal Injury Hazard
make sure oven and light bulb are
cool and power to the range has been
turned off before replacing the light
bulb. Failure to do so could result in
electrical shock or burns.
*The bulb cover must be in place when
using the oven. The cover protects
the bulb from breaking, and from high
oven temperatures. Because bulb
cover is made of glass, be careful not
to drop it. Broken glass could cause
injury.
To replace
the oven
light:
1. Disconnect
supply.
appliance at the main power
2. Remove the glass bulb cover in the back
of the oven by pushing the wire holder to
the side and pulling out bulb cover.
3. Remove the light bulb from its socket.
Replace the bulb with a 40-watt appliance bulb.
4. Replace the bulb cover and snap the
wire holder into place. Reconnect
appliance at the main power supply.
NOTE: Do not use the oven light during the
Self-Cleaning cycle. Use during the SelfCleaning cycle will shorten the life of the
bulb.
32
If You Need Assistance
Service
Or
This section is designed to help you save the cost of a service call. Part 1 of this section
outlines possible problems, their causes, and actions you can take to solve each problem.
Parts 2 and 3 tell you what to do if you still need assistance or service. When calling our
Consumer Assistance Center for help or calling for service, please provide a detailed description of the problem, your appliance’s complete model and serial numbers and the purchase
date. (See page 2.) This information will help us respond properly to your request.
1. Before
calling
for assistance
...
Performance problems often result from little things you can find and fix without tools of any
kind. Please check the chart below for problems you can fix. It could save you the cost of a
service call.
PROBLEM
Nothing
operate
will
POSSIBLE
CAUSE
SOLUTION
The unit is not wired into a live
circuit with proper voltage.
Wire the unit into a live circuit with
proper voltage. (See Installation Instructions.)
A household fuse has blown or a
circuit breaker has tripped.
Replace household fuse or reset circuit
breaker.
The oven
will not
operate
The electronic control has not
been set correctly.
Refer to pages 1 l-20 for setting the
electronic control.
A delayed start time has been
programmed.
Wait for the start time to be reached.
The surface
units will not
operate
A household fuse has blown or a
circuit breaker has tripped.
Replace household fuse or reset circuit
breaker.
Surface units are not plugged in
all the way.
Plug surface units in all the way. (See
“Replacing” on page 28.)
The control knob(s) are not
being set correctly.
Push control knob(s) in before turning to
a setting.
Control
knob(s) will
not turn
You are not pushing in before
turning.
Push control knob(s) in before turning to
a setting.
The SelfCleaning
cycle will
not operate
The range clock does not show
the correct time of day.
Reset clock to show the correct time of
day. (See page 12.)
A delayed start time has been
programmed.
Wait for the start time to be reached.
continued
on next page
33
PROBLEM
POSSIBLE
Cooking
results are not
what you
expected
The range is not level.
CAUSE
The oven temperature
too low or too high.
SOLUTION
Level range. (See Installation
tions.)
seems
Instruc-
Adjust the oven temperature control.
(See “Adjusting the oven temperature
control” on page 14.)
The oven was not preheated
before baking.
Preheat oven when called for in recipe.
The recipe has never been
tested or is not from a reliable
source.
Use only tested recipes from a reliable
source.
The pan used is not the type or Refer to a reliable cookbook for recomsize recommended in the
mended pan type and size.
recipe.
The display
flashing
“88:88”
is
Tones are
sounding and
the display is
flashing error
code
“F-1 ” _ “F-1 0”
34
There is not proper air circulation around pan when baking.
Allow 1% to 2 inches (4-5 cm) of air
space on all sides of pan. There must
be a minimum space of 1 inch
(2.5 cm).
Cooking utensil does not fit the
surface unit being used.
Pan should be the same size or slightly
larger than surface unit being used.
There has been a power
failure.
Reset the clock. (See page 12.)
Push CANCEL. Call for service. (See
Step 3 on page 35.)
2. If you need
assistance
...
Call Whirlpool Consumer Assistance
Center telephone number. Dial free from
anywhere in the U.S.:
1-800-253-l 301
and talk with one of our trained consultants.
The consultant can instruct you in how to
obtain satisfactory operation from your
appliance or, if service is necessary, recommend a qualified service company in your
area.
If you prefer, write to:
Mr. William Clark
Consumer Assistance Representative
Whirlpool Corporation
2000 M-63
Benton Harbor, Ml 49022
Please include a daytime phone number in
your correspondence.
3. If you need
service
...
Whirlpool has a nation01= wide network of author
SERV,CE
nzed WhrrlpoolSM service
companies. Whirlpool
-!!9
service technicians are
trained to fulfill the product warranty and
provide after-warranty service, anywhere in
the United States. To locate the authorized
Whirlpool sewice company in your area, call
our Consumer Assistance Center telephone
number (see Step 2) or look in your telephone directory Yellow Pages under:
ifl
‘APPLIANCE-HOUSEHOLDMAJOR, SERVICE h REPAIR
-See: Whwlpool Appliances or
Aulhormd
Whirlpool Sew~ce
(Example: XYZ Selvce Co.)
* WASHING
DRYERS,
4. If you need FSP@ replacement parts . . .
FSP is a registered trademark of Whirlpool
Corporation for quality parts. Look for this
symbol of quality whenever you need a
replacement part for your Whirlpool appliance. FSP replacement parts will fit right and
work right, because they are made to the
same exacting specifications used to build
every new Whirlpool appliance.
To locate FSP replacement parts in your
area, refer to Step 3 above or call the
Whirlpool Consumer Assistance Center
number in Step 2.
5. If you are not satisfied
how the problem
was
solved . . .
with
Contact the Major Appliance Consumer
Action Panel (MACAP). MACAP is a group
of independent consumer experts that
voices consumer views at the highest
levels of the major appliance industry.
Contact MACAP only when the dealer,
authorized servicer and Whirlpool have
failed to resolve your problem.
Major Appliance Consumer Action Panel
20 North Wacker Drive
Chicago, IL 60606
MACAP will in turn inform us of your
action.
MACHINES
8
SERVICE 8 REPAIR
-See: Whirlpool Applmces
or
Aulhormd
Whirlpool Sewice
(Example. XYZ Service Co.)
35
WHIRLPOOL”
Electric Cooking Product
Warranty
LENGTH OF WARRANTY
WHIRLPOOL
FULL ONE-YEAR
WARRANTY
From Date of Purchase
FSP@ replacement parts and repair labor to correct defects in
materials or workmanship. Service must be provided by an
authorized WhirlpoolSM service company.
WHIRLPOOL
WILL PAY FOR
WILL NOT PAY FOR
A. Service calls to:
1. Correct the installation
of the cooking product.
2. Instruct you how to use the cooking product.
3. Replace house fuses or correct house wiring.
4. Replace owner accessible light bulbs.
6. Repairs when the cooking product is used in other than normal, single-family
use.
household
C. Pickup and delivery. This product is designed to be repaired in the home.
D. Damage to the cooking product caused by accident, misuse, fire, flood, acts of God or
use of products not approved by Whirlpool.
E. Repairs to parts or systems caused by unauthorized
appliance.
modifications
made to the
8-92
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so this limitation or exclusion may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to
state.
Outside the United States, a different warranty may apply. For details, please contact your
authorized Whirlpool distributor or military exchange.
If you need service, first see the “Assistance or Service” section of this book. After checking
“Assistance or Service,” additional help can be found by calling our Consumer Assistance
Center telephone number, 1-800-253-l 301, from anywhere in the U.S.
Q Registered
TrademarmM
PART NO. 56001180143/816986
208136-1030 Rev. 1
Q 1993 Whirlpool
Corporation
Trademark&M
Serwe
Mark of Whirlpool
Corporation
Rev. B
Printed
in Canada
Download PDF