APC | CP16 | User manual | APC CP16 User manual

Broadband PowerShield®
Models: CP16 and CP27
User Manual
990-2366 11/2005
Chapter 1: General Information
The PowerShield® provides a power source for broadband telephony,
Fiber-to-the-Home/Premise (FTTH/P), and other direct current (DC) equipment/applications.
Safety
This manual contains important instructions that should be followed during installation and
maintenance of the APC equipment and batteries. It is intended for APC customers that set up,
install, relocate, or maintain APC equipment.
Changes and modifications to this unit not expressly approved by APC could void the
warranty. Failure to observe this warning may result in serious injury, death, or damage to the
equipment.
Electrical Warnings
Do not work alone under hazardous conditions.
Servicing the PowerShield may require the removal of protective covers, as well as connected utility
power. Use extreme caution during these procedures.
Check that the power cord(s), plug(s), and sockets are in good condition.
Replacement of fuses or other parts must be with identical types and ratings. Substitution of
nonidentical parts may cause safety and fire hazards.
Battery Warning
Danger of explosion if the battery is incorrectly connected or replaced. Use only APC replacement
batteries.
Unpacking
Inspect the unit upon receipt. Notify the shipping carrier or product supplier if there is damage.
The packaging is recyclable; save it for reuse or dispose of it properly.
Check the package contents. The package contains the enclosure, the battery (to be installed), one
power cord, and the product documentation.
1
Specifications
General
Model Number
Input
Output
Maximum
Signal
Voltage
Maximum
Signal
Current
Battery
Type
CP16U48
100-240 V 50/60 Hz 1.0 A
48 V
16 W
30 V
5 mA
CP27U13
100-240 V 50/60 Hz 1.0 A
13 V
27 W
30 V
5 mA
12 V 7.2 AHr
Spill-Proof,
MaintenanceFree,
Sealed Lead
Acid
Environmental
Operating Temperature
-4º F to 122º F (-20º C to 50º C)
Operating Humidity
5 to 95% noncondensing within enclosure
Maximum Operating Elevation
10,000 ft (3,000 m)
Maximum Storage Elevation
50,000 ft (15,000 m)
Storage Temperature
-4º F to 122º F (-20º C to 50º C)
*Battery lifetime is reduced with prolonged storage in
high temperature (>25º C).
Physical
Height x Width x Depth
PowerShield
7.5 x 9.5 x 3 in (19 x 24 x 7.6 cm)
PowerShield carton
13.5 x 13.5 x 4.5 in (34 x 34 x 11 cm)
Weight
PowerShield
7.15 lbs (3.25 kg)
PowerShield with package materials
9 lbs (4 kg)
2
Chapter 2: Installation
Enclosure Installation
Install the enclosure in a protected area that is free of
excessive dust and has adequate airflow.
Do not operate the PowerShield where the temperature
and humidity are outside the specified limits. See
Specifications.
Indoor Use Only
!
"
#
Battery Cover Release Tabs
$ Use screws that are
appropriate for the weight of
this unit and the mounting
surface material. See
Specifications.
3
Battery Installation
!
"
#
Red
Cable
Positive
Terminal
Battery Cover Release Tabs
$
%
4
Black
Cable
Negative
Terminal
Connect Equipment and Power
The PowerShield battery charges when it is connected to utility power. The battery
charges fully during the first eight hours of normal operation. Do not expect full battery
run capability during this initial charge period.
Utility Power
Cord Inlet
Output Power and
Communication
Signals
Optimal Runtime
Extension Connector
1.
Connect the PowerShield to the application equipment (example: FTTH/P Optical Network
Terminal) via the seven-pin output connector, using the appropriate cable (must be ordered
separately). See www.apc.com for a list of available output cables.
2.
Plug the PowerShield power cord into the utility power cord inlet and then into the wall outlet.
Do not overload the wall outlet or circuit.
Cold Start Feature: Upon installation of a charged battery, power will immediately be applied to
the unit even when utility power is not present.
Optional Runtime Extension
The runtime may be extended by adding the external battery CP20B12BP.
5
Chapter 3: Operation
Status Indicators and Features
Front Panel
Status
Indicators
Indicator
Description
Utility
Solid green indicates the unit is on utility power.
Solid yellow indicates that utility power is not present and the unit is on battery
power.
Flashing green LED indicates the unit is fast-charging.
Output
Green indicates the unit is working properly and DC output power is provided
by the battery or the utility power.
Replace Battery/
Alarm Silence
Red indicates that the battery must be replaced or that the battery is
disconnected. See Battery Replacement.
Pressing this button will silence the audible alarm. See Alarm Silence Button.
/
Automatic Self-Test
The unit automatically performs a self-test 31 hours after initial installation. Following this, a battery
self-test will occur every 30 days. See Alarm Silence Button for manual self-test information.
Audible Alarm
Explanation
Description
On
Battery
Four beeps in four seconds will be emitted one time only. This alarm will sound
when the utility power is lost and the unit goes on battery power.
Low
Battery
Voltage
Every five minutes, four beeps in four seconds will be emitted. This alarm will
sound when operating on battery and the battery voltage has dropped below
threshold, indicating that less than 20% of available runtime remains.
Replace Battery
Every fifteen minutes, there will be a quarter-second beep when the battery fails
the automatic self-test.
6
Alarm Silence Button
The audible alarms may be silenced by utilizing the dual function Replace Battery/Alarm Silence
LED/button
/
.
Function
Button Operation
(Press and hold for:)
Description
Replace BatteryTemporarily
Enable/Disable
<4 seconds
If the alarm has been silenced, the unit will
emit one quick beep. If the alarm has been
enabled, two quick beeps will be emitted.
Replace BatteryPermanently
Enable/Disable
8-12 seconds
If the alarm has been silenced, the unit will
emit one quick beep. If the alarm has been
enabled, two quick beeps will be emitted.
Battery Self-TestEnable/Disable
4-8 seconds
A manual self-test can be initiated at any time.
If the self-test has been enabled, three beeps
will be emitted. If the battery self-test has
been canceled, the unit will emit four beeps.
Output Power and Communication Signals
The PowerShield communication signals are isolated from its internal circuitry via open collector
opto-coupled transistors. The connection labeled “Signal Return” is a common return point for all
communication signals. In the typical application, the attached equipment digital ground connects to
Signal Return, and pull-up resistors turn the open collector signals into logic levels.
+Voltage output
 Voltage output
Signal return.
Low when operating from utility line. Open when operating from
battery.
Low when battery is charged. Open when battery fails the Self-Test.
Low when battery is present. Open when battery is missing.
Low when battery is near full charge capacity. Open when operating
from a battery with less than 20% of available runtime remaining.
7
Chapter 4: Maintenance, Service, Approvals, and Warranty
Battery Replacement
This unit has an easy to replace, hot-swappable battery. Replacement is a safe procedure, isolated
from electrical hazards. You may leave the unit and connected equipment on for this procedure.
During the self-test, battery removal and replacement are not recommended. For self-test disabling,
see Alarm Silence Button.
Replace the spent battery with APC replacement battery RBC2. See your dealer or refer to the APC
Web site, www.apc.com, for information on replacement batteries.
For battery replacement, see Battery Installation.
Once the battery is disconnected, the connected equipment is not protected
from power outages.
Be sure to deliver spent batteries to a recycling facility found on the Used
Battery Return Facilities list included with RBC2.
Service
APC makes every effort to ensure parts and equipment arrive in working condition. Occasionally, it
may be necessary to return parts and equipment that are not in working condition.
If the PowerShield requires service, follow these steps:
1.
Contact APC Customer Support through the APC Web site at www.apc.com.
Note the product model number, the serial number, and the date purchased. If you call APC
Customer Support, a technician will ask you to describe the problem and try to solve it over the
phone. If this is not possible, the technician will issue a Returned Material Authorization
Number (RMA#).
If the product is under warranty, repairs are free. If not, there is a repair charge.
Procedures for servicing or returning products may vary internationally. Refer to the APC Web
site. Select the appropriate country from the country selection field. Select Support from the tab
at the top of the web page.
2.
Pack the product in its original packaging.
Pack the unit properly to avoid damage in transit. Never use Styrofoam beads for packaging.
Damage sustained in transit is not covered under warranty.
3.
Mark the RMA# on the outside of the package.
8
4.
Return the unit by insured, prepaid carrier to the address given to you by Customer Support.
Always DISCONNECT THE BATTERY before shipping in compliance with U.S.
Department of Transportation (DOT) regulations.
Contact Information
Refer to the APC Web site, www.apc.com.
Regulatory Approvals
9
Limited Warranty
American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship
for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or
replacing, at its own sole option, any such defective products. To obtain service under warranty you must obtain
a Returned Material Authorization (RMA) number from customer support. Products must be returned with
transportation charges prepaid and must be accompanied by a brief description of the problem encountered and
proof of date and place of purchase. This warranty does not apply to equipment that has been damaged by
accident, negligence, or misapplication or has been altered or modified in any way. This warranty applies only
to the original purchaser who must have properly registered the product within 10 days of purchase.
EXCEPT AS PROVIDED HEREIN, AMERICAN POWER CONVERSION MAKES NO WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties;
therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL APC BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS
PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, APC is not
liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software,
loss of data, costs of substitutes, claims by third parties, or otherwise.
Entire contents copyright 2005 by American Power Conversion Corporation. All rights reserved. Reproduction
in whole or in part without permission is prohibited.
APC, the APC logo and PowerShield are registered trademarks of American Power Conversion Corporation. All
other trademarks are the property of their respective owners.
10
Download PDF