Denon | AVR-4311 | AVR4311 - AWE Europe Ltd

DENON AVR control protocol
Ver.7.2.0
Application model : AVR-4311CI/AVR-4311
Application terminal: RS-232C
Ethernet
Rev 7.2.0
Connector specification
Ⅰ. RS-232C
Connector type: DB-9pin female type, slave straight connection (DCE type)
( 1pin : GND , 2pin : TxD , 3pin : RxD , 5pin : Common(GND) , 4,6,7,8,9pin : NC )
Communication format:
Synchronous system
: Tone step synchronization
Communication system
: A half duplex
Communication speed
: 9600bps
Character length
Parity control
Start bit
Stop bit
Communication procedure
Communication data length
Version
7.2.0
Date
Contents
10.Apr.’10
Original
:
:
:
:
:
:
8 bits
None
1 bit
1 bit
Non procedural
135 bytes (maximum)
Page
-1-
Ⅱ. Ethernet
Connector type
: RJ-45(10BASE-T/100BASE-TX)
Example ①
Ethernet
Cross cable
PC
Example ②
AVR
HUB
PC
AVR
Ethernet
Straight
cable
Communication format
Communication
Communication
Communication
Communication
:
system
speed
port
data length
:
:
:
:
Ethernet
Straight
cable
A half duplex
10Mbps/100Mbps
TCP port 23 (telnet)
135bytes (maximum)
-2-
NETWORK SETUP of AVR-4311
>Procedure of Network Setup mode.
(1)Press MENU button, then Menu appears on FL-display(and GUI)
(2)Select “Manual Setup > Network Setup > Network Connecting > Detail” .
(3)Set parameters described below.
<DHCP>
"ON"---Use this setting when DHCP server is on the local network.
"OFF"---Use this setting when DHCP server is not on the local network.
<IP Address> When <DHCP> sets "OFF”, please set IP address.
When <DHCP> sets "ON”, you can confirm the IP address that is set by server.
<Subnet Mask> When <DHCP> sets "OFF”, please set Subnet Mask.
When <DHCP> sets "ON”, you can confirm the Subnet Mask that is set by server.
<Gateway>
Set the address of Gateway when Gateway is on the local network.
Do not set this parameter when Gateway is not on the local network.
<Primary DNS> Do not set this parameter.
<Second DNS> Do not set this parameter.
<Proxy>
Set this parameter "OFF".
<Network Option: Network Standby Mode>
(1)Press MENU button, then Menu appears on FL-display (and GUI)
(2)Select “Manual Setup > Network Setup > Other > Network Standby”
(3)Set parameters described below.
“ON”---Use this setting when using the AVR-4311 Connected in a network.
“OFF”--- Use this setting when not using the AVR-4311 connected in a network.
This setting is reducing the power consumption in the standby mode.
-3-
Protocol specification
The following three data forms are defined.
COMMAND :
The message sent to a system(AVR) from a controller(Touch Panel etc.)
A command to a system is given from a controller.
EVENT
:
The message sent to a controller (Touch Panel etc.) from a system (AVR)
The result is sent, when a system is operated directly and a state changes.
*The form of EVENT presupposes that it is the same as that of COMMAND.
**Refer to the following table for the contents of COMMAND and EVENT.
RESPONSE :
The message sent to a controller (Touch Panel etc.) from a system (AVR)
if the ‘request command’ (COMMAND+?+CR(0x0D)) has came from a controller.
The RESPONSE should be sent within 200ms of receiving the COMMAND.
*The form of RESPONSE presupposes that it is the same as that of EVENT.
Basic specification: The command by ASCII CODE, parameter expression
*ASCII CODE which can be used is from 0x20 to 0x7F: the alphabet and the number of 0-9, and space (0x20), some signs,
AND carriage return (0x0D) --- It is used only as a pause sign.
Command structure: COMMAND + PARAMETER + CR (0x0D)
COMMAND: ASCII CODE of 2 characters
Ex.
SI : Select Input source
MS : surround Mode Setting
MV : Master Volume setting
PW : system PoWer setting
PARAMETER : ASCII CODE ( up to 25 characters)
ex.
DVD : function name
SUPER STADIUM : surround mode name
*Special Parameter--- ? : for request command
-4-
The example of a command
* <CR> is the meaning of 0x0D.
SIDVD<CR> : Select Input source DVD
MSSTEREO<CR> : surround Mode Set to STEREO
MVUP<CR> : Master Volume UP
PWON<CR> : system PoWer ON
PWSTANDBY<CR> : system PoWer STANDBY
SI?<CR> : Request command for now playing input source >> Return RESPONSE ‘SI***<CR>’
-5-
Others
A) COMMAND is receivable also during transmission of EVENT.
B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels
returns as EVENT.
C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case,
the data of an intact channel is set to "50".
D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel
volume of all channels , It described in B) ) returns as EVENT.
E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME
does NOT return.
F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.
G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned.
H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to
the another request commands(ex. SV command).
I) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME defines “99”.
J) If the MASTER VOLUME & CHANNEL VOLUME set with 0.5dB step, the PARAMETER (with COMMAND and RESPONSE, EVENT) defines three
ASCII characters as bellows.
Ex.
MASTER VOLUME = +1.0dB :
MV81<CR>
+0.5dB :
MV805<CR>
0dB :
MV80<CR>
-0.5dB :
MV795<CR>
-1.0dB :
MV79<CR>
|
|
-79.5dB :
MV005<CR>
-80.0dB :
MV00<CR>
-80.5dB :
MV995<CR>
--:
MV99<CR>
* At the **.0dB step, only uses two ASCII characters as PARAMETER, same as usual.
K) 1 seconds later, please transmit the next COMMAND after transmitting a power on COMMAND(PWON).
-6-
COMMAND and PARAMETER list
COMMAND
PW
PARAMETER
Function
example
ON
POWER ON/STANDBY change
PWON<CR>
STANDBY
PWSTANDBY<CR>
?
Return PW Status
PW?<CR>
MV
UP
MASTER VOLUME UP/DOWN , direct change to **dB
MVUP<CR>
DOWN
MVDOWN<CR>
**:00 to 99 by ASCII , 80=0dB, 99=---(MIN) 995=-80.5dB MV80<CR>
**
?
Return MV Status
MV?<CR>
CV
FL UP
CHANNEL VOLUME UP/DOWN , direct change to **dB
CVFL UP<CR>
FL DOWN
---FRONT L ch
CVFL DOWN<CR>
FL **
**:38 to 62 by ASCII , 50=0dB
CVFL 50<CR>
FR UP
CVFR UP<CR>
FR DOWN
---FRONT R ch
CVFR DOWN<CR>
FR **
**:38 to 62 by ASCII , 50=0dB
CVFR 50<CR>
C UP
CVC UP<CR>
C DOWN
---CENTER ch
CVC DOWN<CR>
C **
**:38 to 62 by ASCII , 50=0dB
CVC 50<CR>
SW UP
CVSW UP<CR>
SW DOWN
---SUBWOOFER(1) ch
CVSW DOWN<CR>
SW **
**:38 to 62 by ASCII , 50=0dB,00=OFF
CVSW 50<CR>
SW2 UP
CVSW2 UP<CR>
SW2 DOWN
CVSW2 DOWN<CR>
---SUBWOOFER(2) ch
SW2 **
CVSW2 50<CR>
**:38 to 62 by ASCII , 50=0dB,00=OFF
SL UP
CVSL UP<CR>
SL DOWN
---SURROUND L ch
CVSL DOWN<CR>
SL **
**:38 to 62 by ASCII , 50=0dB
CVSL 50<CR>
SR UP
CVSR UP<CR>
SR DOWN
---SURROUND R ch
CVSR DOWN<CR>
SR **
**:38 to 62 by ASCII , 50=0dB
CVSR 50<CR>
SBL UP
---SURROUND BACK L ch (SB ch 2SP)
CVSBL UP<CR>
SBL DOWN
CVSBL DOWN<CR>
SBL **
**:38 to 62 by ASCII , 50=0dB
CVSBL 50<CR>
MV, CV COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
-7-
COMMAND
CV
PARAMETER
function
example
SBR UP
---SURROUND BACK R ch (SB ch 2SP)
CVSBR UP<CR>
SBR DOWN
CVSBR DOWN<CR>
SBR **
**:38 to 62 by ASCII , 50=0dB
CVSBR 50<CR>
SB UP
---SURROUND BACK ch
(SB ch 1SP)
CVSB UP<CR>
SB DOWN
CVSB DOWN<CR>
SB **
**:38 to 62 by ASCII , 50=0dB
CVSB 50<CR>
FHL UP
CVFHL UP<CR>
FHL DOWN
---FRONT HEIGHT L ch
CVFHL DOWN<CR>
FHL **
**:38 to 62 by ASCII , 50=0dB
CVFHL 50<CR>
FHR UP
CVFHR UP<CR>
FHR DOWN
---FRONT HEIGHT R ch
CVFHR DOWN<CR>
FHR **
**:38 to 62 by ASCII , 50=0dB
CVFHR 50<CR>
FWL UP
CVFWL UP<CR>
FWL DOWN
---FRONT WIDE L ch
CVFWL DOWN<CR>
FWL **
**:38 to 62 by ASCII , 50=0dB
CVFWL 50<CR>
FWR UP
CVFWR UP<CR>
FWR DOWN
---FRONT WIDE R ch
CVFWR DOWN<CR>
FWR **
**:38 to 62 by ASCII , 50=0dB
CVFWR 50<CR>
?
Return CV Status
CV?<CR>
MU
ON
OUTPUT MUTE ON/OFF change
MUON<CR>
OFF
MUOFF<CR>
?
Return MU Status
MU?<CR>
SI
PHONO
Select INPUT source
SIPHONO<CR>
CD
SICD<CR>
TUNER
(Except AVR-4311CI model)
SITUNER<CR>
DVD
SIDVD<CR>
BD
SIBD<CR>
TV
SITV<CR>
SAT/CBL
SISAT/CBL<CR>
DVR
SIDVR<CR>
GAME
SIGAME<CR>
V.AUX
SIV.AUX<CR>
DOCK
SIDOCK<CR>
CV COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
-8-
COMMAND
SI
ZM
SR
PARAMETER
SIRIUS
HDRADIO
IPOD
NET/USB
RHAPSODY
NAPSTER
PANDORA
LASTFM
FLICKR
FAVORITES
IRADIO
SERVER
USB/IPOD
?
ON
OFF
?
PHONO
|
USB/IPOD
SOURCE
?
function
(North America model Only)
(AVR-4311CI model Only)
Select iPod (dock or USB) and PLAY
(North America model Only)
(North America & Europe model Only)
(North America model Only)
(Europe model Only)
Select USB or iPod Direct
Return SI Status
MAIN ZONE ON/OFF change
Return ZM Status
REC SELECT mode set , and select source
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
REC SELECT mode cancel
Return SR Status
-9-
example
SISIRIUS<CR>
SIHDRADIO<CR>
SIIPOD<CR>
SINET/USB<CR>
SIRHAPSODY<CR>
SINAPSTER<CR>
SIPANDORA<CR>
SILASTFM<CR>
SIFLICKR<CR>
SIFAVORITES<CR>
SIIRADIO<CR>
SISERVER<CR>
SIUSB/IPOD<CR>
SI?<CR>
ZMON<CR>
ZMOFF<CR>
ZM?<CR>
SRPHONO<CR>
|
SRUSB/IPOD<CR>
SRSOURCE<CR>
SR?<CR>
COMMAND
SD
DC
SV
SLP
PARAMETER
AUTO
HDMI
DIGITAL
ANALOG
EXT.IN
NO
?
AUTO
PCM
DTS
?
DVD
BD
TV
SAT/CBL
DVR
GAME
V.AUX
DOCK
SOURCE
?
OFF
***
?
function
Set AUTO mode (Priority:HDMI>>DIGITAL>>ANALOG)
Set force HDMI INPUT mode
Set force DIGITAL INPUT (Optical,Coaxial)mode
Set force ANALOG INPUT mode
Set EXT.IN mode
---When no input
Return SD Status
Set DIGITAL INPUT AUTO mode
Set DIGITAL INPUT force PCM mode
Set DIGITAL INPUT force DTS mode
Return DC Status
VIDEO SELECT mode set , and select source
VIDEO SELECT mode cancel
Return SV Status
MAIN ZONE SLEEP TIMER setting
***:001 to 120 by ASCII , 010=10min
Return SLP Status
- 10 -
example
SDAUTO<CR>
SDHDMI<CR>
SDDIGITAL<CR>
SDANALOG<CR>
SDEXT.IN<CR>
SDNO<CR>
SD?<CR>
DCAUTO<CR>
DCPCM<CR>
DCDTS<CR>
DC?<CR>
SVDVD<CR>
SVBD<CR>
SVTV<CR>
SVSAT/CBL<CR>
SVDVR<CR>
SVGAME<CR>
SVV.AUX<CR>
SVDOCK<CR>
SVSOURCE<CR>
SV?<CR>
SLPOFF<CR>
SLP120<CR>
SLP?<CR>
COMMAND
MS
PARAMETER
DIRECT
PURE DIRECT
STEREO
STANDARD
DOLBY DIGITAL
DTS SUROUND
MCH STEREO
WIDE SCREEN
SUPER STADIUM
ROCK ARENA
JAZZ CLUB
CLASSIC CONCERT
MONO MOVIE
MATRIX
VIDEO GAME
VIRTUAL
?
QUICK1
QUICK2
QUICK3
QUICK4
QUICK5
QUICK1 MEMORY
QUICK2 MEMORY
QUICK3 MEMORY
QUICK4 MEMORY
QUICK5 MEMORY
QUICK ?
function
Select SURROUND mode
---5/7/9/11CH STEREO mode
Return MS Status
QUICK SELECT 1-5 MODE SELECT
QUICK SELECT 1-5 MODE MEMORY
Return MSQUICK Status
- 11 -
example
MSDIRECT<CR>
MSPURE DIRECT<CR>
MSSTEREO<CR>
MSSTANDARD<CR>
MSDOLBY DIGITAL<CR>
MSDTS SURROUND<CR>
MSMCH STEREO<CR>
MSWIDE SCREEN<CR>
MSSUPER STADIUM<CR>
MSROCK ARENA<CR>
MSJAZZ CLUB<CR>
MSCLASSIC CONCERT<CR>
MSMONO MOVIE<CR>
MSMATRIX<CR>
MSVIDEO GAME<CR>
MSVIRTUAL<CR>
MS?<CR>
MSQUICK1<CR>
MSQUICK2<CR>
MSQUICK3<CR>
MSQUICK4<CR>
MSQUICK5<CR>
MSQUICK1 MEMORY<CR>
MSQUICK2 MEMORY<CR>
MSQUICK3 MEMORY<CR>
MSQUICK4 MEMORY<CR>
MSQUICK5 MEMORY<CR>
MSQUICK ?<CR>
COMMAND
VS
PARAMETER
MONIAUTO
MONI1
MONI2
MONI ?
ASPNRM
ASPFUL
ASP ?
SC48P
SC10I
SC72P
SC10P
SC10P24
SCAUTO
SC ?
SCH48P
SCH10I
SCH72P
SCH10P
SCH10P24
SCHAUTO
SCH ?
AUDIO AMP
AUDIO TV
AUDIO ?
VPMAUTO
VPMGAME
VPMMOVI
VPM ?
VST ON
VST OFF
VST ?
function
Set HDMI MONITOR automatic detection
Set HDMI MONITOR OUT-1
Set HDMI MONITOR OUT-2
Return VSMONI Status
Set Normal mode
Set FULL mode
Return VSASP Status
Set Resolution to 480p/576p
Set Resolution to 1080i
Set Resolution to 720p
Set Resolution to 1080p
Set Resolution to 1080p:24Hz
Set Resolution to AUTO
Return VSSC Status
Set Resolution to 480p/576p (HDMI)
Set Resolution to 1080i(HDMI)
Set Resolution to 720p(HDMI)
Set Resolution to 1080p(HDMI)
Set Resolution to 1080p:24Hz(HDMI)
Set Resolution to AUTO(HDMI)
Return VSSCH Status(HDMI)
Set HDMI AUDIO Output to AMP
Set HDMI AUDIO Output to TV
Return VSAUDIO Status
Set Video Processing Mode to AUTO
Set Video Processing Mode to GAME
Set Video Processing Mode to MOVIE
Return VSVPM Status
Set VERTICAL STRETCH to ON
Set VERTICAL STRETCH to OFF
Return VSVST Status
- 12 -
example
VSMONIAUTO<CR>
VSMONI1<CR>
VSMONI2<CR>
VSMONI ?<CR>
VSASPNRM<CR>
VSASPFUL<CR>
VSASP ?<CR>
VSSC48P<CR>
VSSC10I<CR>
VSSC72P<CR>
VSSC10P<CR>
VSSC10P24<CR>
VSSCAUTO<CR>
VSSC ?<CR>
VSSC48P<CR>
VSSC10I<CR>
VSSC72P<CR>
VSSC10P<CR>
VSSC10P24<CR>
VSSCAUTO<CR>
VSSCH ?<CR>
VSAUDIO AMP<CR>
VSAUDIO TV<CR>
VSAUDIO ?<CR>
VSVPMAUTO<CR>
VSVPMGAME<CR>
VSVPMMOVI<CR>
VSVPM ?<CR>
VSVST ON<CR>
VSVST OFF<CR>
VSVST ?<CR>
COMMAND
PS
PARAMETER
TONE CTRL OFF
TONE CTRL ON
TONE CTRL ?
SB:MTRX ON
SB:PL2X CINEMA
SB:PL2X MUSIC
SB:ON
SB:OFF
SB: ?
CINEMA EQ.ON
CINEMA EQ.OFF
CINEMA EQ. ?
MODE:MUSIC
MODE:CINEMA
MODE:GAME
MODE:PRO LOGIC
MODE: ?
DOLVOL ON
DOLVOL OFF
DOLVOL ?
VOLLEV LOW
VOLLEV MID
VOLLEV HI
VOLLEV ?
VOLMOD HLF
VOLMOD FUL
VOLMOD OFF
VOLMOD ?
FH:ON
FH:OFF
FH: ?
function
PARAMETER setting
TONE CONTROL ON/OFF
Return PSTONE CONTROL Status
SURROUND BACK SP MODE set
Return PSSB: Status
CINEMA EQ. ON/OFF
Return PSCINEMA EQ.Status
CINEMA / MUSIC / GAME / PL mode change
(This parameter can change DOLBY PL2,PL2x,NEO:6 mode.)
---SB=ON:PL2x mode / SB=OFF:PL2 mode
--- GAME can change DOLBY PL2 & PL2x mode
--- PL can change ONLY DOLBY PL2 mode
Return PSMODE: Status
Dolby Volume direct change
Return PSDOLVOL Status
Dolby Volume Leveler direct change
Return PSVOLLEV Status
Dolby Volume Modeler direct change
Return PSVOLMOD Status
FRONT HEIGHT ON/OFF
Return PSFH: Status
- 13 -
example
PSTONE CTRL OFF<CR>
PSTONE CTRL OFF<CR>
PSTONE CTRL ?<CR>
PSSB:MTRX ON<CR>
PSSB:PL2X CINEMA<CR>
PSSB:PL2X MUSIC<CR>
PSSB:ON<CR>
PSSB:OFF<CR>
PSSB: ?<CR>
PSCINEMA EQ.ON<CR>
PSCINEMA EQ.OFF<CR>
PSCINEMA EQ. ?<CR>
PSMODE:MUSIC<CR>
PSMODE:CINEMA<CR>
PSMODE:GAME<CR>
PSMODE:PRO LOGIC<CR>
PSMODE: ?<CR>
PSDOLVOL ON<CR>
PSDOLVOL OFF<CR>
PSDOLVOL ?<CR>
PSVOLLEV LOW<CR>
PSVOLLEV MID<CR>
PSVOLLEV HI<CR>
PSVOLLEV ?<CR>
PSVOLMOD HLF<CR>
PSVOLMOD FUL<CR>
PSVOLMOD OFF<CR>
PSVOLMOD ?<CR>
PSFH:ON<CR>
PSFH:OFF<CR>
PSFH: ?<CR>
COMMAND
PS
PARAMETER
PHG LOW
PHG MID
PHG HI
PHG ?
SP:FH
SP:FW
SP:HW
SP:OFF
SP: ?
MULTEQ:AUDYSSEY
MULTEQ:BYP.LR
MULTEQ:FLAT
MULTEQ:MANUAL
MULTEQ:OFF
MULTEQ: ?
DYNEQ ON
DYNEQ OFF
DYNEQ ?
REFLEV 0
REFLEV 5
REFLEV 10
REFLEV 15
REFREV ?
DYNVOL NGT
DYNVOL EVE
DYNVOL DAY
DYNVOL ?
DSX ONHW
DSX ONH
DSX ONW
DSX OFF
DSX ?
function
PLⅡz HEIGHT GAIN direct change
Return PSPHG Status
Speaker Output set(F.Height/F.Wide)
Return PSSP: Status
MultEQ XT 32 mode direct change
Return PSMULTEQ: Status
Dynamic EQ = ON
Dynamic EQ = OFF
Return PSDYNEQ Status
Reference Level Offset=0dB
Reference Level Offset=5dB
Reference Level Offset=10dB
Reference Level Offset=15dB
Return PSREFLEV Status
Dynamic Volume = Midnight
Dynamic Volume = Evening
Dynamic Volume = Day
Return PSDYNVOL Status
Audyssey DSX ON(Height/Wide)
Audyssey DSX ON(Height)
Audyssey DSX ON(Wide)
Audyssey DSX OFF
Return PSDSX Status
- 14 -
example
PSPHG LOW<CR>
PSPHG MID<CR>
PSPHG HI<CR>
PSPHG ?<CR>
PSSP:FH<CR>
PSSP:FW<CR>
PSSP:HW<CR>
PSSP:OFF<CR>
PSSP: ?<CR>
PSMULTEQ:AUDYSSEY<CR>
PSMULTEQ:BYP.LR<CR>
PSMULTEQ:FLAT<CR>
PSMULTEQ:MANUAL<CR>
PSMULTEQ:OFF<CR>
PSMULTEQ: ?<CR>
PSDYNEQ ON<CR>
PSDYNEQ OFF<CR>
PSDYNEQ ?<CR>
PSREFLEV 0<CR>
PSREFLEV 5<CR>
PSREFLEV 10<CR>
PSREFLEV 15<CR>
PSREFLEV ?<CR>
PSDYNVOL NGT<CR>
PSDYNVOL EVE<CR>
PSDYNVOL DAY<CR>
PSDYNVOL ?<CR>
PSDSX ONHW<CR>
PSDSX ONH<CR>
PSDSX ONW<CR>
PSDSX OFF<CR>
PSDSX ?<CR>
COMMAND
PS
PARAMETER
function
STW UP
STAGE WIDTH UP/DOWN , direct change to **
PSSTW
STW DOWN
**:40 to 60 by ASCII , 50=0dB
PSSTW
STW **
---AVR-4311 can be operated from -10 to +10
PSSTW
STW ?
Return PSSTW Status
PSSTW
STH UP
STAGE HEIGHT UP/DOWN , direct change to **
PSSTH
STH DOWN
**:40 to 60 by ASCII , 50=0dB
PSSTH
STH **
---AVR-4311 can be operated from -10 to +10
PSSTH
STH ?
Return PSSTH Status
PSSTH
BAS UP
BASS UP/DOWN , direct change to **
PSBAS
BAS DOWN
**:44 to 56 by ASCII , 50=0dB
PSBAS
BAS **
---AVR-4311 can be operated from -6 to +6
PSBAS
BAS ?
Return PSBAS Status
PSBAS
TRE UP
TREBLE UP/DOWN , direct change to **
PSTRE
TRE DOWN
**:44 to 56 by ASCII , 50=0dB
PSTRE
TRE **
---AVR-4311 can be operated from -6 to +6
PSTRE
TRE ?
Return PSTRE Status
PSTRE
DRC AUTO
DRC direct change
PSDRC
DRC LOW
PSDRC
DRC MID
PSDRC
DRC HI
PSDRC
DRC OFF
PSDRC
DRC ?
Return PSDRC Status
PSDRC
DCO OFF
D.COMP direct change
PSDCO
DCO LOW
PSDCO
DCO MID
PSDCO
DCO HIGH
PSDCO
DCO ?
Return PSDCO Status
PSDCO
LFE UP
LFE UP/DOWN , direct change to **
PSLEE
LFE DOWN
**:00 to 10 by ASCII , 00=0dB, 10=-10dB
PSLFE
LFE **
---AVR-4311 can be operated from 0 to -10
PSLFE
LFE ?
Return PSLFE Status
PSLFE
PS COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
- 15 -
example
UP<CR>
DOWN<CR>
50<CR>
?<CR>
UP<CR>
DOWN<CR>
50<CR>
?<CR>
UP<CR>
DOWN<CR>
50<CR>
?<CR>
UP<CR>
DOWN<CR>
50<CR>
?<CR>
AUTO<CR>
LOW<CR>
MID<CR>
HI<CR>
OFF<CR>
?<CR>
OFF<CR>
LOW<CR>
MID<CR>
HIGH<CR>
?<CR>
UP<CR>
DOWN<CR>
10<CR>
? <CR>
COMMAND
PS
PARAMETER
function
EFF ON
EFFECT ON/OFF direct change
PSEFF
EFF OFF
PSEFF
EFF UP
EFFECT UP/DOWN , EFFECT LEVEL direct change to **
PSEFF
EFF DOWN
**:00 to 15 by ASCII , 00=0dB, 10=10dB
PSEFF
EFF **
---AVR-4311 can be operated from 1 to 15
PSEFF
EFF ?
Return PSEFF Status
PSEFF
DEL UP
DELAY UP/DOWN , direct change to ***
PSDEL
DEL DOWN
***:000 to 300 by ASCII , 000=0ms, 300=300ms
PSDEL
DEL ***
---AVR-4311 can be operated from 0 to 300
PSDEL
DEL ?
Return PSDEL Status
PSDEL
AFD ON
AFDM ON/OFF
PSAFD
AFD OFF
PSAFD
AFD ?
Return PSAFD Status
PSAFD
PAN ON
PANORAMA ON/OFF
PSPAN
PAN OFF
PSPAN
PAN ?
Return PSPAN Status
PSPAN
DIM UP
DIMENSION UP/DOWN , direct change to **
PSDIM
DIM DOWN
**:00 to 06 by ASCII , 00=0,
PSDIM
DIM **
---AVR-4311 can be operated from 0 to 6
PSDIM
DIM ?
Return PSDIM Status
PSDIM
CEN UP
CENTER WIDTH UP/DOWN , direct change to **
PSCEN
CEN DOWN
**:00 to 07 by ASCII , 00=0
PSCEN
CEN **
---AVR-4311 can be operated from 0 to 7
PSCEN
CEN ?
Return PSCEN Status
PSCEN
CEI UP
CENTER IMAGE UP/DOWN , direct change to **
PSCEI
CEI DOWN
**:00 to 10 by ASCII , 00=0.0
PSCEI
CEI **
---AVR-4311 can be operated from 0.0 to 1.0
PSCEI
CEI?
Return PSCEI Status
OSCEI
ATT ON
SW ATT ON/OFF
PSATT
ATT OFF
PSATT
ATT ?
Return PSATT Status
PSATT
PS COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
- 16 -
example
ON<CR>
OFF<CR>
UP<CR>
DOWN<CR>
10<CR>
?<CR>
UP<CR>
DOWN<CR>
***<CR>
?<CR>
ON<CR>
OFF<CR>
?<CR>
ON<CR>
OFF<CR>
?<CR>
UP<CR>
DOWN<CR>
**<CR>
?<CR>
UP<CR>
DOWN<CR>
07<CR>
?<CR>
UP<CR>
DOWN<CR>
10<CR>
?<CR>
ON<CR>
OFF<CR>
?<CR>
COMMAND
PS
PARAMETER
function
example
SWR ON
SW ON/OFF
PSSWR ON<CR>
SWR OFF
PSSWR OFF<CR>
SWR ?
Return PSSWR Status
PSSWR ?<CR>
RSZ S
ROOM SIZE direct change
PSRSZ S<CR>
RSZ MS
PSRSZ MS<CR>
RSZ M
PSRSZ M<CR>
RSZ ML
PSRSZ ML<CR>
RSZ L
PSRSZ L<CR>
RSZ ?
Return PSRSZ Status
PSRSZ ?<CR>
DELAY UP
AUDIO DELAY UP/DOWN , direct change to ***dB
PSDELAY UP<CR>
DELAY DOWN
***:000 to 200 by ASCII , 000=0ms, 200=200ms
PSDELAY DOWN<CR>
DELAY ***
---AVR-4311 can be operated from 0 to 200
PSDELAY 200<CR>
DELAY ?
Return PSDELAY Status
PSDELAY ?<CR>
RSTR OFF
AUDIO RESTORER direct change
PSRSTR OFF<CR>
RSTR MODE1
PSRSTR MODE1<CR>
RSTR MODE2
PSRSTR MODE2<CR>
RSTR MODE3
PSRSTR MODE3<CR>
RSTR ?
Return PSRSTR Status
PSRSTR ?<CR>
PS COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
- 17 -
COMMAND
PV
PARAMETER
function
CN UP
CONTRAST UP/DOWN , direct change to **
CN DOWN
**:44 to 56 by ASCII , 50=0
CN **
---AVR-4311 can be operated from -6 to +6(44 to 56)
CN ?
Return PSCN Status
BR UP
BRIGHTNESS UP/DOWN , direct change to **
BR DOWN
**:00 to 12 by ASCII , 00=0
BR **
---AVR-4311 can be operated from 0 to 12
BR ?
Return PSBR Status
CM UP
CHROMA LEVEL UP/DOWN , direct change to **
CM DOWN
**:44 to 56 by ASCII , 50=0
CM **
---AVR-4311 can be operated from -6 to +6(44 to 56)
CM ?
Return PSCN Status
HUE UP
HUE UP/DOWN , direct change to **
HUE DOWN
**:44 to 56 by ASCII , 50=0
HUE **
---AVR-4311 can be operated from -6 to +6(44 to 56)
HUE ?
Return PSCN Status
DNR OFF
DNR direct change
DNR LOW
DNR MID
DNR HI
DNR ?
Return PVDNR Status
ENH UP
ENHANCER UP/DOWN, direct change to **
ENH DOWN
**:00 to 12 by ASCII, 00=0
ENH **
---AVR-4311 can be operated from 0 to 12
ENH ?
Return PVENH Status
PV COMMAND : "*" parameter uses two ASCII characters. (see page6 J) section)
- 18 -
example
PVCN UP<CR>
PVCN DOWN<CR>
PVCN 50<CR>
PVCN ?<CR>
PVBR UP<CR>
PVBR DOWN<CR>
PVBR 12<CR>
PVBR ?<CR>
PVCM UP<CR>
PVCM DOWN<CR>
PVCM 50<CR>
PVCM ?<CR>
PVHUE UP<CR>
PVHUE DOWN<CR>
PVHUE 50<CR>
PVHUE ?<CR>
PVDNR OFF<CR>
PVDNR LOW<CR>
PVDNR MID<CR>
PVDNR HI<CR>
PVDNR ?<CR>
PVENH UP<CR>
PVENH DOWN<CR>
PVENH 12<CR>
PVENH ?<CR>
COMMAND
Z2
PARAMETER
function
PHONO
ZONE2 mode set , and select source
|
---The name of PARAMETER is
USB/IPOD
the same as that of the time of SI COMMAND.
SOURCE
ZONE2 mode cancel
UP
ZONE2 VOLUME UP/DOWN , direct change to **dB
DOWN
**
**:00 to 99 by ASCII , 80=0dB, 99=---(MIN) 00=-80dB
ON
ZONE2 ON/OFF change
OFF
?
Return Z2 Status
Z2MU
ON
ZONE2 OUTPUT MUTE ON/OFF change
OFF
?
Return Z2MU Status
Z2CS
ST
ZONE2 Channel setting
MONO
?
Return Z2CS Status
Z2CV
FL UP
ZONE2 CHANNEL VOLUME UP/DOWN , direct change to **dB
FL DOWN
---FRONT Lch
FL **
**:38 to 62 by ASCII , 50=0dB
FR UP
ZONE2 CHANNEL VOLUME UP/DOWN , direct change to **dB
FR DOWN
---FRONT Rch
FR **
**:38 to 62 by ASCII , 50=0dB
?
Return Z2CV Status
Z2HPF
ON
ZONE2 HPF ON/OFF
OFF
?
Return Z2HPF Status
Z2、Z2CV COMMAND : "*" parameter uses two ASCII characters. (see page6 J) section)
- 19 -
example
Z2PHONO<CR>
|
Z2USB/IPOD<CR>
Z2SOURCE<CR>
Z2UP<CR>
Z2DOWN<CR>
Z280<CR>
Z2ON<CR>
Z2OFF<CR>
Z2?<CR>
Z2MUON<CR>
Z2MUOFF<CR>
Z2MU?<CR>
Z2CSST<CR>
Z2CSMONO<CR>
Z2CS?<CR>
Z2CVFL UP<CR>
Z2CVFL DOWN<CR>
Z2CVFL 50<CR>
Z2CVFR UP<CR>
Z2CVFR DOWN<CR>
Z2CVFR 50<CR>
Z2CV?<CR>
Z2HPFON<CR>
Z2HPFOFF<CR>
Z2HPF?<CR>
COMMAND
Z2PS
PARAMETER
function
example
BAS UP
ZONE2 BASS UP/DOWN , direct change to **dB
Z2PSBAS UP<CR>
BAS DOWN
**:40 to 60 by ASCII , 00=0dB
Z2PSBAS DOWN<CR>
BAS **
---AVR-4311 can be operated from -10 to +10
Z2PSBAS 50<CR>
BAS ?
Return Z2PSBAS Status
Z2PSBAS ?<CR>
TRE UP
ZONE2 TREBLE UP/DOWN , direct change to **dB
Z2PSTRE UP<CR>
TRE DOWN
**:40 to 60 by ASCII , 00=0dB
Z2PSTRE DOWN<CR>
TRE **
---AVR-4311 can be operated from -10 to +10
Z2PSTRE 50<CR>
TRE ?
Return Z2PSTRE Status
Z2PSTRE ?<CR>
Z2
QUICK1
ZONE2 QUICK SELECT 1-5 MODE SELECT
Z2QUICK1<CR>
QUICK2
Z2QUICK2<CR>
QUICK3
Z2QUICK3<CR>
QUICK4
Z2QUICK4<CR>
QUICK5
Z2QUICK5<CR>
QUICK1 MEMORY
ZONE2 QUICK SELECT 1-5 MODE MEMORY
Z2QUICK1 MEMORY<CR>
QUICK2 MEMORY
Z2QUICK2 MEMORY<CR>
QUICK3 MEMORY
Z2QUICK3 MEMORY<CR>
QUICK4 MEMORY
Z2QUICK4 MEMORY<CR>
QUICK5 MEMORY
Z2QUICK5 MEMORY<CR>
QUICK ?
Return Z2QUICK Status
Z2QUICK ?<CR>
Z2SLP
OFF
ZONE2 SLEEP TIMER setting
Z2SLPOFF<CR>
***
***:001 to 120 by ASCII , 010=10min
Z2SLP120<CR>
?
Return Z2SLP Status
Z2SLP?<CR>
Z2 COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
- 20 -
COMMAND
Z3
Z3MU
Z3CS
Z3CV
Z3HPF
PARAMETER
PHONO
|
USB/IPOD
SOURCE
UP
DOWN
**
ON
OFF
?
ON
OFF
?
ST
MONO
?
FL UP
FL DOWN
FL **
FR UP
FR DOWN
FR **
?
ON
OFF
?
function
ZONE3 mode set , and select source
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
ZONE3 mode cancel
ZONE3 VOLUME UP/DOWN , direct change to **dB
**:00 to 99 by ASCII , 80=0dB, 99=---(MIN) 00=-80dB
ZONE3 ON/OFF change at AVR-4311
Return Z3 Status
ZONE3 OUTPUT MUTE ON/OFF change
Return Z3MU Status
ZONE3 Channel setting
Return Z3CS Status
ZONE3 CHANNEL VOLUME
---FRONT Lch
**:38 to 62 by ASCII
ZONE3 CHANNEL VOLUME
---FRONT Rch
**:38 to 62 by ASCII
Return Z3CV Status
ZONE3 HPF ON/OFF
UP/DOWN , direct change to **dB
, 50=0dB
UP/DOWN , direct change to **dB
, 50=0dB
Return Z3HPF Status
Z3, Z3CV COMMAND : "*" parameter uses two ASCII characters. (see page6 J) section)
- 21 -
example
Z3PHONO<CR>
|
Z3USB/IPOD<CR>
Z3SOURCE<CR>
Z3UP<CR>
Z3DOWN<CR>
Z380<CR>
Z3ON<CR>
Z3OFF<CR>
Z3?<CR>
Z3MUON<CR>
Z3MUOFF<CR>
Z3MU?<CR>
Z3CSST<CR>
Z3CSMONO<CR>
Z3CS?<CR>
Z3CVFL UP<CR>
Z3CVFL DOWN<CR>
Z3CVFL 50<CR>
Z3CVFR UP<CR>
Z3CVFR DOWN<CR>
Z3CVFR 50<CR>
Z3CV?<CR>
Z3HPFON<CR>
Z3HPFOFF<CR>
Z3HPF?<CR>
COMMAND
Z3PS
Z3
Z3SLP
PARAMETER
BAS UP
BAS DOWN
BAS **
BAS ?
TRE UP
TRE DOWN
TRE **
TRE ?
QUICK1
QUICK2
QUICK3
QUICK4
QUICK5
QUICK1 MEMORY
QUICK2 MEMORY
QUICK3 MEMORY
QUICK4 MEMORY
QUICK5 MEMORY
QUICK ?
OFF
***
?
function
ZONE3 BASS UP/DOWN , direct change to **dB
**:00 to 99 by ASCII , 00=0dB
--- AVR-4311 can be operated from -10 to +10(40 to 60)
Return Z3PSBAS Status
ZONE3 TREBLE UP/DOWN , direct change to **dB
**:00 to 99 by ASCII , 00=0dB
--- AVR-4311 can be operated from -10 to +10(40 to 60)
Return Z3PSTRE Status
ZONE3 QUICK SELECT 1-5 MODE SELECT
ZONE3 QUICK SELECT 1-5 MODE MEMORY
Return Z3QUICK Status
ZONE3 SLEEP TIMER setting
***:001 to 120 by ASCII , 010=10min
Return Z3SLP Status
example
Z3PSBAS UP<CR>
Z3PSBAS DOWN<CR>
Z3PSBAS 50<CR>
Z3PSBAS ?<CR>
Z3PSTRE UP<CR>
Z3PSTRE DOWN<CR>
Z3PSTRE 50<CR>
Z3PSTRE ?<CR>
Z3QUICK1<CR>
Z3QUICK2<CR>
Z3QUICK3<CR>
Z3QUICK4<CR>
Z3QUICK5<CR>
Z3QUICK1 MEMORY<CR>
Z3QUICK2 MEMORY<CR>
Z3QUICK3 MEMORY<CR>
Z3QUICK4 MEMORY<CR>
Z3QUICK5 MEMORY<CR>
Z3QUICK ?<CR>
Z3SLPOFF<CR>
Z3SLP120<CR>
Z3SLP?<CR>
Z3PS COMMAND : "*" parameter uses two or three ASCII characters. (see page6 J) section)
- 22 -
※ANALOG TUNER Control (except AVR-4311CI model)
COMMAND
TF
TP
TM
PARAMETER
ANUP
ANDOWN
AN******
(6 digits)
AN?
ANUP
ANDOWN
AN**
(PRESET No.)
AN?
ANMEM
ANAM
ANFM
AN?
ANAUTO
ANMANUAL
function
TUNER Frequency UP/DOWN
--- ****.** kHz at AM band (>050000 is AM.)
****.** MHz at FM band (<050000 is FM.)
Return TF Status
TUNER PRESET CH UP/DOWN , direct change to No.**
Return TP Status
TUNER PRESET MEMORY
TUNER BAND , MODE Select
---Band set to AM
---Band set to FM
Return TM Status
---Tuning mode set to AUTO mode
---Tuning mode set to MANUAL mode
example
TFANUP<CR>
TFANDOWN<CR>
TFAN105000<CR>
(1050.00kHz at AM)
TFAN?<CR>
TPANUP<CR>
TPANDOWN<CR>
TPANA1<CR>
(PRESET No.”A1”)
TPAN?<CR>
TPANMEM<CR>
TMANAM<CR>
TMANFM<CR>
TMAN?<CR>
TMANAUTO<CR>
TMANMANUAL<CR>
TF, TP, TM COMMAND : '*' parameters can NOT operate when INPUT source isn’t TUNER.
- 23 -
※SIRIUS Control(North America model only)
COMMAND
TF
TP
ST
PARAMETER
STUP
STDOWN
ST***
(3 digits)
STPL****
(4 digits)
ST?
STUP
STDOWN
ST**(PRESET No.)
function
SIRIUS Channel UP/DOWN
ST?
STMEM
?
Return TPST Status
SIRIUS PRESET MEMORY
Return ST Status
- CHANNEL NAME, ARTIST, COMPOSER,TITLE, SIGNAL LEVEL
--- ***:ST CH No.
--- ***:Parental Lock Code Number
Return TFST Status
SIRIUS PRESET CH UP/DOWN , direct change to No.**
- 24 -
example
TFSTUP<CR>
TFSTDOWN<CR>
TFST001<CR>
(ST001 CH at SIRIUS TUNER)
TFSTPL1234<CR>
(Parental Lock code “1234”
TFST?<CR>
TPSTUP<CR>
TPSTDOWN<CR>
TPSTA1<CR>
(PRESET No.”A1”)
TPST?<CR>
TPSTMEM<CR>
ST?<CR>
※HD RADIO Control(AVR-4311CI North America model only)
COMMAND
TM
PARAMETER
HDUP
HDDOWN
HD******
(6 digits)
HDMC*
(1 digit)
HD?
HDUP
HDDOWN
HD**
(PRESET No.)
HD?
HDMEM
HDAM
HD
HDFM
HD?
HDAUTOHD
HDAUTO
HDMANUAL
?
TF
TP
function
HD Channel UP/DOWN , direct change
--- ****.** kHz at AM band (>050000 is AM.)
****.** MHz at FM band (<050000 is FM.)
---HD Multi Cast CH Select
(*:Multi Cast 1∼8, Analog 0)
Return TFHD Status
HD PRESET CH UP/DOWN , direct change to No.**
Return TPHD Status
HD PRESET MEMORY
HD RADIO BAND , MODE Select
---Band set to AM
---Band set to FM
Return TMHD Status
---Tuning mode set to AUTO-HD mode
---Tuning mode set to AUTO mode
---Tuning mode set to MANUAL mode
Return HD Status
---BAND, STATION NAME, MULTI CAST CURRENT,
MULTI CAST NUMBER, SIGNAL LEVEL,
ARTIST, TITLE,ALBUM, GENRE, PROGRAM TYPE, MODE
- 25 -
example
TFHDUP<CR>
TFHDDOWN<CR>
TFHD105000<CR>
(1050.00kHz at AM)
TFHDMC2<CR>
TFHD?<CR>
TPHDUP<CR>
TPHDDOWN<CR>
TPHDA1<CR>
(PRESET No.”A1”)
TPHD?<CR>
TPHDMEM<CR>
TMHDAM<CR>
TMHDFM<CR>
TMHD?<CR>
TMHDAUTOHD<CR>
TMHDAUTO<CR>
TMHDMANUAL<CR>
HD?<CR>
※Network Audio/USB /iPod DIRECT Extended Control
COMMAND
SI
Z2
Z3
SI
Z2
Z3
NS
PARAMETER
USB
USB
USB
IPD
IPD
IPD
90
91
92
93
94
9A
9B
9C
9D
9E
9H
9I
9J
9K
9M
9W
9X
9Y
PT
function
NET/USB and USB Start Playback
NET/USB and USB Start Playback
NET/USB and USB Start Playback
NET/USB and iPod Direct Start Playback
NET/USB and iPod Direct Start Playback
NET/USB and iPod Direct Start Playback
Select INPUT source
Select ZONE2 source
Select ZONE3 source
Select INPUT source
Select ZONE2 source
Select ZONE3 source
“Cursor Up” Control
“Cursor Down” Control
“Cursor Left” Control
“Cursor Right” Control
“Enter (Play/Pause)” Control
“Play” Control(iRadio/mServer/USB)
“Play/Pause” Control(iPod Direct)
“Pause” Control
“Play/Pause” Control(iPod Direct)
“Stop” Control
“Skip Plus” Control
“Skip Minus” Control
“Repeat One” (USB/iPod DIRECT/mServer/Rhapsody/Napster)
“Repeat All” (USB/iPod DIRECT/mServer/Rhapsody/Napster)
“Repeat Off” (USB/iPod DIRECT/mServer/Rhapsody/Napster)
“Random On/Repeat ALL” (USB/mServer/Rhapsody/Napster)
“Shuffle Songs” Control (iPod Direct Only)
“Random Off” (USB/mServer/Rhapsody/Napster)
“Shuffle Off” Control (iPod Direct Only)
Toggle Switch “Browse Mode/Remote Mode″Control
(iPod Direct Only)
“Page Next” Control
“Page Previous” Control
Enter/Exit PARTY MODE
- 26 -
example
SIUSB<CR>
Z2USB<CR>
Z3USB<CR>
SIIPD<CR>
Z2IPD<CR>
Z3IPD<CR>
NS90<CR>
NS91<CR>
NS92<CR>
NS93<CR>
NS94<CR>
NS9A<CR>
NS9B<CR>
NS9C<CR>
NS9D<CR>
NS9E<CR>
NS9H<CR>
NS9I<CR>
NS9J<CR>
NS9K<CR>
NS9M<CR>
NS9W<CR>
NS9X<CR>
NS9Y<CR>
NSPT<CR>
COMMAND
NSA
PARAMETER
NSE
NSB
**
NSC
**
NSD
*
function
Return Onscreen Display Information List
(ASCII CODE Character)
Request Onscreen Display Information List
(UTF-8 CODE Character)
“Direct Preset CH Play”
example
NSA<CR>
(Return NSA0-NSA8,Refer to Page 49)
NSE<CR>
(Return NSE0-NSE8,Refer to Page 50)
NSB00<CR>
(**:00-55,00=A1,01=A2,B1=08,G8=55)
“Direct Preset CH Memory”(iRadio/mServer only)
NSC00<CR>
(**:00-55,00=A1,01=A2,B1=08,G8=55)
“Direct Character Search”(iRadio/mServer/USB/Rhapsody only) NSD0<CR>
(*:0-9,A-Z)
- 27 -
※ iPod dock Extended Control
※iPod Dock which AVR-4311 can connect with is ASD-1R/11R.
COMMAND
PARAMETER
function
IP
90
“Cursor Up” Control
91
“Cursor Down” Control
92
“Cursor Left” Control
93
“Cursor Right” Control
94
“Enter (Play/Pause)” Control
9A
“Play/Pause” Control
9C
“Stop” Control
9D
“Skip Plus” Control
9E
“Skip Minus” Control
9F
“Manual Search Plus” Control
9G
“Manual Search Minus” Control
9H
“Repeat One” Control
9I
“Repeat All” Control
9J
“Repeat Off” Control
9K
“Shuffle Songs” Control
9L
“Shuffle Album” Control
9M
“Shuffle Off” Control
9N
“MENU” Control
9P
Switch the “Browse Mode” Control
9Q
Switch the “Remote Mode” Control
9X
“Page Next” Control
9Y
“Page Previous” Control
IPA
Return Onscreen Display Information List
(ASCII CODE Character)
IPE
Request Onscreen Display Information List(iPod)
(UTF-8 CODE Character)
- 28 -
example
IP90<CR>
IP91<CR>
IP92<CR>
IP93<CR>
IP94<CR>
IP9A<CR>
IP9C<CR>
IP9D<CR>
IP9E<CR>
IP9F<CR>
IP9G<CR>
IP9H<CR>
IP9I<CR>
IP9J<CR>
IP9K<CR>
IP9L<CR>
IP9M<CR>
IP9N<CR>
IP9P<CR>
IP9Q<CR>
IP9X<CR>
IP9Y<CR>
IPA<CR>
(Return IPA0-IPA9,Refer to Page 51-52)
IPE<CR>
(Return IPE0-IPE9,Refer to Page 53-54)
※Cursor/Enter/Menu(Setup)
COMMAND
MN
PARAMETER
CUP
CDN
CLT
CRT
ENT
RTN
MEN ON
MEN OFF
SRC ON
SRC OFF
function
“Cursor Up” Control
“Cursor Down” Control
“Cursor Left” Control
“Cursor Right” Control
“Enter” Control
“RETURN” Control
“GUI Menu ON” Control
“GUI Menu OFF” Control
“GUI Source Select Menu ON” Control
“GUI Source Select Menu OFF” Control
- 29 -
example
MNCUP<CR>
MNCDN<CR>
MNCLT<CR>
MNCRT<CR>
MNENT<CR>
MNRTN<CR>
MNMEN ON<CR>
MNMEN OFF<CR>
MNSRC ON<CR>
MNSRC OFF<CR>
※Remote Lock/Panel Lock
COMMAND
SY
PARAMETER
REMOTE LOCK ON
REMOTE LOCK OFF
PANEL LOCK ON
PANEL+V LOCK ON
PANEL LOCK OFF
※UPGRADE ID Display
COMMAND
PARAMETER
UG
IDN
function
REMOTE CONTROL LOCK ON/OFF
PANEL BUTTON (Except MASTER VOL.)CONTROL LOCK ON
PANEL BUTTON & MASTER VOL. CONTROL LOCK ON
PANEL BUTTUM & MASTER VOL. CONTROL LOCK OFF
example
SYREMOTE LOCK ON<CR>
SYREMOTE LOCK OFF<CR>
SYPANEL LOCK ON<CR>
SYPANEL+V LOCK ON<CR>
SYPANEL LOCK OFF<CR>
function
ID Number for UPGRADE is displayed on FL Display
UGIDN<CR>
- 30 -
example
EVENT(or RESPONSE) and PARAMETER list
EVENT
PW
MV
CV
PARAMETER
ON
STANDBY
**
function
POWER ON/STANDBY change
MASTER VOLUME change , **:00 to 99 by ASCII
98 = 18dB(MAX)
80 = 0dB
00 = -80dB
995 = -80.5dB
99 = ---(MIN)
CHANNEL VOLUME change , **:00,38 to 62 by ASCII
62 = +12dB(MAX)
50 = 0dB
38 = -12dB(MIN)
example
PWON<CR>
PWSTANDBY<CR>
MV80<CR>
FL **
CVFL 50<CR>
FR **
CVFR 50<CR>
C **
CVC 50<CR>
SW **
CVSW 50<CR>
SW2 **
CVSW2 50<CR>
SL **
CVSL 50<CR>
SR **
CVSR 50<CR>
SBL **
(at SBch 2SP)
CVSBL 50<CR>
SBR **
(at SBch 2SP)
CVSBR 50<CR>
SB **
(at SBch 1SP)
CVSB 50<CR>
FHL **
CVFHL 50<CR>
FHR **
CVFHR 50<CR>
FWL **
CVFWL 50<CR>
FWR **
CVFWR 50<CR>
MU
ON
OUTPUT MUTE ON/OFF change
MUON<CR>
OFF
MUOFF<CR>
SI
PHONO
INPUT source change
SIPHONO<CR>
CD
SICD<CR>
TUNER
(Except AVR-4311CI model)
SITUNER<CR>
DVD
SIDVD<CR>
BD
SIBD<CR>
TV
SITV<CR>
SAT/CBL
SISAT/CBL<CR>
DVR
SIDVR<CR>
The PARAMETER of MV, CV EVENT : Uses two or three ASCII characters. (see page6 J) section)
- 31 -
EVENT
SI
ZM
SR
SD
DC
PARAMETER
GAME
V.AUX
DOCK
SIRIUS
HDRADIO
IPOD
RHAPSODY
NAPSTER
FAVORITES
IRADIO
SERVER
USB DIRECT
IPOD DIRECT
USB
IPD
ON
OFF
PHONO
|
IPOD DIRECT
SOURCE
AUTO
HDMI
DIGITAL
ANALOG
EXT.IN
ARC
NO
AUTO
PCM
DTS
function
(North America model Only)
(AVR-4311CI model Only)
(North America model Only)
(North America & Europe model Only)
MAIN ZONE ON/OFF change
REC SELECT source change
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
REC SELECT mode cancel
INPUT mode change
ARC playing
No Input
DIGITAL INPUT mode change
- 32 -
example
SIGAME<CR>
SIV.AUX<CR>
SIDOCK<CR>
SISIRIUS<CR>
SIHDRADIO<CR>
SIIPOD<CR>
SIRHAPSODY<CR>
SINAPSTER<CR>
SIFAVORITES<CR>
SIIRADIO<CR>
SISERVER<CR>
SIUSB DIRECT<CR>
SIIPOD DIRECT<CR>
SIUSB<CR>
SIIPD<CR>
ZMON<CR>
ZMOFF<CR>
SRPHONO<CR>
SRSOURCE<CR>
SDAUTO<CR>
SDHDMI<CR>
SDDIGITAL<CR>
SDANALOG<CR>
SDEXT.IN<CR>
SDARC<CR>
SDNO<CR>
DCAUTO<CR>
DCPCM<CR>
DCDTS<CR>
EVENT
SV
SLP
PARAMETER
DVD
BD
TV
SAT/CBL
DVR
GAME
V.AUX
DOCK
SOURCE
OFF
***
function
VIDEO SELECT mode source change
MAIN ZONE SLEEP TIMER setting change
- 33 -
example
SVDVD<CR>
SVBD<CR>
SVTV<CR>
SVSAT/CBL<CR>
SVDVR<CR>
SVGAME<CR>
SVV.AUX<CR>
SVDOCKCR>
SVSOURCE<CR>
SLPOFF<CR>
SLP120<CR>
EVENT
MS
PARAMETER
DIRECT
DSD DIRECT
PURE DIRECT
STEREO
MULTI CH IN
M CH IN+PL2X C
M CH IN+PL2X M
M CH IN+PL2Z H
M CH IN
+DOLBY EX
MULTI CH IN 7.1
DOLBY PRO LOGIC
DOLBY PL2 C
DOLBY PL2 M
DOLBY PL2 G
DOLBY PL2X C
DOLBY PL2X M
DOLBY PL2X G
DOLBY PL2Z H
DOLBY DIGITAL
DOLBY D EX
DOLBY D
+PL2X C
DOLBY D
+PL2X M
DOLBY D
+PL2Z H
DTS NEO:6 C
DTS NEO:6 M
DTS SURROUND
DTS ES DSCRT6.1
DTS ES MTRX6.1
DTS+PL2X C
DTS+PL2X M
function
SURROUND mode change
example
MSDIRECT<CR>
MSDSD DIRECT<CR>
MSPURE DIRECT<CR>
MSSTEREO<CR>
MSMULTI CH IN<CR>
MSM CH IN+PL2X C<CR>
MSM CH IN+PL2X M<CR>
MSM CH IN+PL2Z H<CR>
MSM CH IN+DOLBY EX<CR>
MSMULTI
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
MSDOLBY
CH IN 7.1<CR>
PRO LOGIC<CR>
PL2 C<CR>
PL2 M<CR>
PL2 G<CR>
PL2X C<CR>
PL2X M<CR>
PL2X G<CR>
PL2Z H<CR>
DIGITAL<CR>
D EX<CR>
D+PL2X C<CR>
MSDOLBY D+PL2X M<CR>
MSDOLBY D+PL2Z H<CR>
MSDTS NEO:6 C<CR>
MSDTS NEO:6 M<CR>
MSDTS SURROUND<CR>
MSDTS ES DSCRT6.1<CR>
MSDTS ES MTRX6.1<CR>
MSDTS+PL2X C<CR>
MSDTS+PL2X M<CR>
- 34 -
EVENT
MS
PARAMETER
function
DTS+PL2Z H
DTS+NEO:6
DTS96/24
DTS96 ES MTRX
MCH STEREO
---5/7/9/11CH STEREO mode
WIDE SCREEN
SUPER STADIUM
ROCK ARENA
JAZZ CLUB
CLASSIC CONCERT
MONO MOVIE
MATRIX
VIDEO GAME
VIRTUAL
DOLBY D+
DOLBY D+ +EX
DOLBY D+ +PL2X C
DOLBY D+ +PL2X M
DOLBY D+ +PL2Z H
DOLBY TRUEHD
DOLBY HD
DOLBY HD+EX
DOLBY HD+PL2X C
DOLBY HD+PL2X M
DOLBY HD+PL2Z H
DTS HD
DTS HD MSTR
DTS HD+NEO:6
DTS HD+PL2X C
DTS HD+PL2X M
DTS HD+PL2Z H
DTS ES 8CH DSCRT
DTS EXPRESS
- 35 -
example
MSDTS+PL2Z H<CR>
MSDTS+NEO:6<CR>
MSDTS96/24<CR>
MSDTS96 ES MTRX<CR>
MSMCH STEREO<CR>
MSWIDE SCREEN<CR>
MSSUPER STADIUM<CR>
MSROCK ARENA<CR>
MSJAZZ CLUB<CR>
MSCLASSIC CONCERT<CR>
MSMONO MOVIE<CR>
MSMATRIX<CR>
MSVIDEO GAME<CR>
MSVIRTUAL<CR>
MSDOLBY D+<CR>
MSDOLBY D+ +EX<CR>
MSDOLBY D+ +PL2X C<CR>
MSDOLBY D+ +PL2X M<CR>
MSDOLBY D+ +PL2Z H<CR>
MSDOLBY HD<CR>
MSDOLBY HD<CR>
MSDOLBY HD+EX<CR>
MSDOLBY HD+PL2X C<CR>
MSDOLBY HD+PL2X M<CR>
MSDOLBY HD+PL2Z H<CR>
MSDTS HD<CR>
MSDTS HD MSTR<CR>
MSDTS HD+NEO:6<CR>
MSDTS HD+PL2X C<CR>
MSDTS HD+PL2X M<CR>
MSDTS HD+PL2Z H<CR>
MSDTS ES 8CH DSCRT<CR>
MSDTS EXPRESS<CR>
EVENT
MS
PARAMETER
MPEG2 AAC
AAC+DOLBY EX
AAC+PL2X C
AAC+PL2X M
AAC+PL2Z H
AUDYSSEY DSX
PL DSX
PL2 C DSX
PL2 M DSX
PL2 G DSX
PL2X C DSX
PL2X M DSX
PL2X G DSX
NEO:6 C DSX
NEO:6 M DSX
QUICK1
QUICK2
QUICK3
QUICK4
QUICK5
QUICK0
function
(JAPAN
(JAPAN
(JAPAN
(JAPAN
(JAPAN
model
model
model
model
model
Only)
Only)
Only)
Only)
Only)
QUICK SELECT mode change
---QUICK 1(or 2, 3, 4, 5) Change QUICK SELECT OFF
- 36 -
example
MSMPEG2 AAC<CR>
MSAAC+DOLBY EX<CR>
MSAAC+PL2X C<CR>
MSAAC+PL2X M<CR
MSAAC+PL2Z H<CR>
MSAUDYSSEY DSX<CR>
MSPL DSX<CR>
MSPL2 C DSX<CR>
MSPL2 M DSX<CR>
MSPL2 G DSX<CR>
MSPL2X C DSX<CR>
MSPL2X M DSX<CR>
MSPL2X G DSX<CR>
MSNEO:6 C DSX<CR>
MSNEO:6 M DSX<CR>
MSQUICK1<CR>
MSQUICK2<CR>
MSQUICK3<CR>
MSQUICK4<CR>
MSQUICK5<CR>
MSQUICK0<CR>
EVENT
VS
PARAMETER
MONIAUTO
MONI1
MONI2
ASPNRM
ASPFUL
SC48P
SC10I
SC72P
SC10P
SC10P24
SCAUTO
SCH48P
SCH10I
SCH72P
SCH10P
SCH10P24
SCHAUTO
AUDIO AMP
AUDIO TV
VPMAUTO
VPMGAME
VPMMOVI
VST ON
VST OFF
VST ?
function
HDMI MONITOR setting change
ASPECT setting change
Resolution(analog) setting change
Resolution(HDMI) setting change
HDMI AUDIO Output setting change
Video Mode setting change
- 37 -
example
VSMONIAUTO<CR>
VSMONI1<CR>
VSMONI2<CR>
VSASPNRM<CR>
VSASPFUL<CR>
VSSC48P<CR>
VSSC10I<CR>
VSSC72P<CR>
VSSC10P<CR>
VSSC10P24<CR>
VSSCAUTO<CR>
VSSCH48P<CR>
VSSCH10I<CR>
VSSCH72P<CR>
VSSCH10P<CR>
VSSCH10P24<CR>
VSSCHAUTO<CR>
VSAUDIO AMP<CR>
VSAUDIO TV<CR>
VSVPMAUTO<CR>
VSVPMGAME<CR>
VSVPMMOVI<CR>
VSVST ON<CR>
VSVST OFF<CR>
VSVST ? <CR>
EVENT
PS
PARAMETER
TONE CTRL OFF
TONE CTRL ON
SB:MTRX ON
SB:PL2X CINEMA
SB:PL2X MUSIC
SB:ON
SB:OFF
SB:ESDSCRT
SB:ESMTRX
SB:DSCRT ON
CINEMA EQ.ON
CINEMA EQ.OFF
MODE:CINEMA
MODE:MUSIC
MODE:GAME
MODE:PRO LOGIC
MODE:HEIGHT
DOLVOL ON
DOLVOL OFF
VOLLEV LOW
VOLLEV MID
VOLLEV HI
VOLMOD HLF
VOLMOD FUL
VOLMOD OFF
FH:ON
FH:OFF
PHG LOW
PHG MID
PHG HI
function
TONE CONTROL ON/OFF change
SURROUND BACK MODE change
CINEMA EQ. ON/OFF change
CINEMA / MUSIC / GAME / PL /HEIGHT mode change
Dolby Volume change
Dolby Volume Leveler change
Dolby Volume Modeler change
FRONT HEIGHT Output change
PLⅡz HEIGHT GAIN direct change
- 38 -
example
PSTONE CTRL OFF<CR>
PSTONE CTRL OFF<CR>
PSSB:MTRX ON<CR>
PSSB:PL2X CINEMA<CR>
PSSB:PL2X MUSIC<CR>
PSSB:ON<CR>
PSSB:OFF<CR>
PSSB:ESDSCRT<CR>
PSSB:ESMTRX<CR>
PSSB:DSCRT ON<CR>
PSCINEMA EQ.ON<CR>
PSCINEMA EQ.OFF<CR>
PSMODE:CINEMA<CR>
PSMODE:MUSIC<CR>
PSMODE:GAME<CR>
PSMODE:PRO LOGIC<CR>
PSMODE:HEIGHT<CR>
PSDOLVOL ON<CR>
PSDOLVOL OFF<CR>
PSVOLLEV LOW<CR>
PSVOLLEV MID<CR>
PSVOLLEV HI<CR>
PSVOLMOD HLF<CR>
PSVOLMOD FUL<CR>
PSVOLMOD OFF<CR>
PSFH:ON<CR>
PSFH:OFF<CR>
PSPHG LOW<CR>
PSPHG MID<CR>
PSPHG HI<CR>
EVENT
PS
PARAMETER
SP:FH
SP:FW
SP:HW
SP:OFF
MULTEQ:AUDYSSEY
MULTEQ:BYP.LR
MULTEQ:FLAT
MULTEQ:MANUAL
MULTEQ:OFF
DYNEQ ON
DYNEQ OFF
REFLEV 0
REFLEV 5
REFLEV 10
REFLEV 15
DYNVOL NGT
DYNVOL EVE
DYNVOL DAY
DSX ONHW
DSX ONH
DSX ONW
DSX OFF
STW **
STH **
BAS **
TRE **
DRC AUTO
DRC LOW
DRC MID
DRC HI
DRC OFF
function
Speaker Output set(F.Height/F.Wide)
MultEQ XT mode change
DYNAMIC EQ change
Reference Level Offset change
DYNAMIC VOLUME change
Audyssey DSX change
STAGE WIDTH change
STAGE HEIGHT change
BASS change
TREBLE change
DRC change
- 39 -
example
PSSP:FH<CR>
PSSP:FW<CR>
PSSP:HW<CR>
PSSP:OFF<CR>
PSMULTEQ:AUDYSSEY<CR>
PSMULTEQ:BYP.LR<CR>
PSMULTEQ:FLAT<CR>
PSMULTEQ:MANUAL<CR>
PSMULTEQ:OFF<CR>
PSDYNEQ ON<CR>
PSDYNEQ OFF<CR>
PSREFLEV 0<CR>
PSREFLEV 5<CR>
PSREFLEV 10<CR>
PSREFLEV 15<CR>
PSDYNVOL NGT<CR>
PSDYNVOL EVE<CR>
PSDYNVOL DAY<CR>
PSDSX ONHW<CR>
PSDSX ONH<CR>
PSDSX ONW<CR>
PSDSX OFF<CR>
PSSTW 50<CR>
PSSTH 50<CR>
PSBAS 50<CR>
PSTRE 50<CR>
PSDRC AUTO<CR>
PSDRC LOW<CR>
PSDRC MID<CR>
PSDRC HI<CR>
PSDRC OFF<CR>
EVENT
PS
PARAMETER
DCO OFF
DCO LOW
DCO MID
DCO HIGH
LFE **
EFF **
DEL ***
AFD ON
AFD OFF
PAN ON
PAN OFF
DIM **
CEN **
CEI **
ATT ON
ATT OFF
SWR ON
SWR OFF
RSZ S
RSZ MS
RSZ M
RSZ ML
RSZ L
DELAY ***
RSTR OFF
RSTR MODE1
RSTR MODE2
RSTR MODE3
function
D.COMP change
LFE change
EFFECT LEVEL change
DELAY change
AFDM change
PANORAMA change
DIMMENSION change
CENTER WIDTH change
CENTER IMAGE change
ATT ON/OFF change
SW ON/OFF change
ROOM SIZE change
AUDIO DELAY change
AUDIO RESTORER change
- 40 -
example
PSDCO OFF<CR>
PSDCO LOW<CR>
PSDCO MID<CR>
PSDCO HIGH<CR>
PSLFE 10<CR>
PSEFF 10<CR>
PSDEL ***<CR>
PSAFD ON<CR>
PSAFD OFF<CR>
PSPAN ON<CR>
PSPAN OFF<CR>
PSDIM **<CR>
PSCEN 07<CR>
PSCEI 10<CR>
PSATT ON
PSATT OFF
PSSWR ON<CR>
PSSWR OFF<CR>
PSRSZ S<CR>
PSRSZ MS<CR>
PSRSZ M<CR>
PSRSZ ML<CR>
PSRSZ L<CR>
PSDELAY 200<CR>
PSRSTR OFF<CR>
PSRSTR MODE1<CR>
PSRSTR MODE2<CR>
PSRSTR MODE3<CR>
EVENT
PV
PARAMETER
CN **
BR **
CM **
HUE **
DNR OFF
DNR LOW
DNR MID
DNR HI
ENH **
function
CONTRAST change
BRIGHTNESS Change
CROMA LEVEL change
Hue Change
DNR change
ENHANCER change
- 41 -
example
PVCN 50<CR>
PVBR 12<CR>
PVCM 50<CR>
PVHUE 50<CR>
PVDNR OFF<CR>
PVDNR LOW<CR>
PVDNR MID<CR>
PVDNR HI<CR>
PVENH 12<CR>
EVENT
Z2
PARAMETER
PHONO
|
USB DIRECT
IPOD DIRECT
SOURCE
QUICK1
QUICK2
QUICK3
QUICK4
QUICK5
QUICK0
**
function
ZONE2 source change
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
ZONE2 mode cancel
ZONE2 QUICK SELECT mode change
---Z2 QUICK SELECT 1(or 2, 3, 4, 5)
Change QUICK SELCT OFF
ZONE2 VOLUME change , **:00 to 99 by ASCII
98 = 18dB(MAX)
80 = 0dB
10 = -70dB
00 = -80dB
99 = ---(MIN)
ZONE2 ON/OFF change
example
Z2PHONO<CR>
|
Z2USB DIRECT<CR>
Z2IPOD DIRECT<CR>
Z2SOURCE<CR>
Z2QUICK1<CR>
Z2QUICK2<CR>
Z2QUICK3<CR>
Z2QUICK4<CR>
Z2QUICK5<CR>
Z2QUICK0<CR>
Z280<CR>
ON
Z2ON<CR>
OFF
Z2OFF<CR>
Z2MU
ON
ZONE2 OUTPUT MUTE ON/OFF change
Z2MUON<CR>
OFF
Z2MUOFF<CR>
Z2CS
ST
ZONE2 Channel setting
Z2CSST<CR>
MONO
Z2CSMONO<CR>
Z2CV
FL **
**:38 to 62 by ASCII , 50=0dB
Z2CVFL 50<CR>
FR **
**:38 to 62 by ASCII , 50=0dB
Z2CVFR 50<CR>
Z2HPF
ON
ZONE2 HPF ON/OFF change
Z2HPFON<CR>
OFF
Z2HPFOFF<CR>
Z2PS
BAS **
ZONE2 BASS change
Z2PSBAS 50<CR>
TRE **
ZONE2 TEBLE change
Z2PSTRE 50<CR>
Z2SLP
OFF
Z2SLPOFF<CR>
ZONE2 SLEEP TIMER setting change
***
Z2SLP120<CR>
The PARAMETER of Z2 EVENT : Uses two or three ASCII characters. (see page4 J) section)
- 42 -
EVENT
Z3
PARAMETER
PHONO
|
USB DIRECT
IPOD DIRECT
SOURCE
QUICK1
QUICK2
QUICK3
QUICK4
QUICK5
QUICK0
**
function
ZONE3 source change
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
ZONE3 mode cancel
ZONE3 QUICK SELECT mode change
---Z3 QUICK SELECT 1(or 2, 3, 4, 5)
Change QUICK SELCT OFF
ZONE3 VOLUME change , **:00 to 99 by ASCII
98 = 18dB(MAX)
80 = 0dB
10 = -70dB
00 = -80dB
99 = ---(MIN)
ZONE3 ON/OFF change
example
Z3PHONO<CR>
|
Z3USB DIRECT<CR>
Z3IPOD DIRECT<CR>
Z3SOURCE<CR>
Z3QUICK1<CR>
Z3QUICK2<CR>
Z3QUICK3<CR>
Z3QUICK4<CR>
Z3QUICK5<CR>
Z3QUICK0<CR>
Z380<CR>
ON
Z3ON<CR>
OFF
Z3OFF<CR>
Z3MU
ON
ZONE3 OUTPUT MUTE ON/OFF change
Z3MUON<CR>
OFF
Z3MUOFF<CR>
Z3CS
ST
ZONE3 Channel setting
Z3CSST<CR>
MONO
Z3CSMONO<CR>
Z3CV
FL **
**:38 to 62 by ASCII , 50=0dB
Z3CVFL 50<CR>
FR **
**:38 to 62 by ASCII , 50=0dB
Z3CVFR 50<CR>
Z3HPF
ON
ZONE3 HPF ON/OFF change
Z3HPFON<CR>
OFF
Z3HPFOFF<CR>
Z3PS
BAS **
Z3PSBAS 50<CR>
ZONE3 BASS change
TRE **
Z3PSTRE 50<CR>
ZONE3 TEBLE change
Z3SLP
OFF
Z3SLPOFF<CR>
ZONE3 SLEEP TIMER setting change
***
Z3SLP120<CR>
The PARAMETER of Z3 EVENT : Uses two or three ASCII characters. (see page4 J) section)
- 43 -
※ANALOG TUNER Control(except AVR-4311CI North America model)
EVENT
TF
PARAMETER
AN******
(6 digits)
TP
AN**(PRESET No.)
TM
ANOFF
ANAM
ANFM
ANAUTO
ANMANUAL
function
TUNER Frequency change
--- ****.** kHz at AM band
****.** MHz at FM band
TUNER PRESET change to No.**
Change Preset Channel select OFF
TUNER BAND , MODE change
---Band set to AM
---Band set to FM
---Tuning mode set to AUTO mode
---Tuning mode set to MANUAL mode
- 44 -
example
TFAN105000<CR>
(1050.00kHz at AM)
TPANA1<CR>
(PRESET No.”A1”)
TPANOFF<CR>
TMANAM<CR>
TMANFM<CR>
TMANAUTO<CR>
TMANMANUAL<CR>
※SIRIUS Control(North America model only)
TF
COMMAND
PARAMETER
ST*** (3 digits)
--- ***:ST CH No.
TP
STPL ON
STPL OFF
STUL OK
STUL NG
STCH SUB
STCH UNS
STMP VAL
STMP INV
ST CHECK ANT
ST** (PRESET No.)
Parental Lock Status “ON”
Parental Lock Status “OFF”
Unlocking is successful
Unlocking is failed
Subscribed channel
Unsubscribed channel
Valid Channel
Invalid Channel
SIRIUS TUNER is not connected
SIRIUS PRESET change to No.**
STOFF
CH NAME
*****************
***
(20 digits)
ARTIST
*****************
(36 digits)
TITLE
*****************
(36 digits)
COMPOSER
*****************
(36 digits)
ID ************
(12 digits)
SIGNAL EXCELLENT
SIGNAL GOOD
SIGNAL WEAK
SIGNAL NOSIGNAL
Change Preset Channel select OFF
SIRIUS CH NAME change
ST
function
example
TFST001<CR>
(ST001 CH at SIRIUS TUNER)
TFSTPL ON<CR>
TFSTPL OFF<CR>
TFSTUL OK<CR>
TFSTUL NG<CR>
TFSTCH SUB<CR>
TFSTCH UNS<CR>
TFSTMP VAL<CR>
TFSTMP INV<CR>
TFST CHECK ANT<CR>
TPSTA1<CR>
(PRESET No.”A1”)
TPSTOFF<CR>
STCH NAME LONG CHANNEL NAM<CR>
SIRIUS ARTIST NAME change
STARTIST High and mighty color
<CR>
SIRIUS TITLE NAME change
STTITLE Memory Crysis
<CR>
SIRIUS COMPOSER NAME change
STCOMPOSER High and mighty color
<CR>
SIRIUS ID(SR000 Selected)
STID 123456789012<CR>
SIRIUS ANTENNA SIGNAL STATUS change
STSIGNAL
STSIGNAL
STSIGNAL
STSIGNAL
- 45 -
EXCELLENT<CR>
GOOD<CR>
WEAK<CR>
NOSIGNAL<CR>
※HD RADIO Control(AVR-4311CI North America model only)
EVENT
TF
PARAMETER
HD******
(6 digits)
HDMC*(1 digit)
TP
HD**(PRESET No.)
TM
HD
HDAM
HDFM
HDAUTOHD
HDAUTO
HDMANUAL
ST NAME(8 digits)
STL NAME
(56 digits)
SIG LEV *
(1 digit)
MLT CURRCH *
(1 digit)
MLT CAST CH
(1 digits)
PTY(18 digits)
ARTIST(40 digits)
TITLE(40 digits)
ALBUM(40 digits)
GENRE(23 digits)
MODE
function
--- ****.** kHz at AM band (>050000 is AM.)
****.** MHz at FM band (<050000 is FM.)
---HD Multi Cast CH change
(*:Multi Cast 1∼8, Analog 0)
HD PRESET change to No.**
HD RADIO BAND , MODE change
---Band set to AM
---Band set to FM
---Tuning mode set to AUTO-HD mode
---Tuning mode set to AUTO mode
---Tuning mode set to MANUAL mode
HD STATION NAME change
HD STATION LONG NAME change
HD ANTENNA SIGNAL STATUS change
example
TPHD105000<CR>
(1050.00kHz at AM)
TFHDMC2<CR>
TPHDA1<CR>
(PRESET No.”A1”)
TMHDAM<CR>
TMHDFM<CR>
TMHDAUTOHD<CR>
TMHDAUTO<CR>
TMHDMANUAL<CR>
HDST NAME ********<CR>
HDSTL NAME (56 digits)<CR>
HD MULTI CAST CURRENT CH change
HDSIG
HDSIG
HDSIG
HDSIG
HDSIG
HDSIG
HDSIG
HDMLT
HD MULTI CAST CH NUMBER
HDMLT CAST CH *<CR>
HD
HD
HD
HD
HD
HD
HDPTY (18 digits)<CR>
HDARTIST (40 digits)<CR>
HDTITLE (40 digits)<CR>
HDALBUM (40 digits)<CR>
HDGENRE (23 digits)<CR>
HDMODE DIGITAL<CR>
HDMODE ANALOG<CR>
PROGRAM TYPE change
ARTIST NAME change
TITLE NAME change
ALBUM NAME change
GANRE change
MODE(ANALOG/DIGITAL)
- 46 -
LEV 0<CR>
LEV 1<CR>
LEV 2<CR>
LEV 3<CR>
LEV 4<CR>
LEV 5<CR>
LEV 6<CR>
CURRCH *<CR>
※Network Audio/USB /iPod DIRECT Extended Control
EVENT
PARAMETER
NSA
0
1
2
3
4
5
6
7
8
function
Onscreen Display Information is Answered
By the NSA Command.
Display Line1 Information
Display Line3 Information
Display Line4 Information
Display Line5 Information
Display Line6 Information
Display Line7 Information
Display Line8 Information
Display Line9 Information
Display Line10 Information
- 47 -
NSA0**************_?????<CR>
NSA1※************_?????<CR>
NSA2※************_?????<CR>
NSA3※************_?????<CR>
NSA4※************_?????<CR>
NSA5※************_?????<CR>
NSA6※************_?????<CR>
NSA7**************_?????<CR>
NSA8**************_?????<CR>
*:Character Length MAX96
_:Null
?:Exclusion(The character after Null
should be disregarded)
※:Cursor&Playable Music
Information Data(1Byte)
Bit1:Playable Music
Bit2:Directory
Bit4:CURSOR SELECT=1
Bit7:Picture
Bit3,5,6,8:Don't Care
NSA0Now Playing USB_????<CR>
NSA1※Come Away With Me_???<CR>
NSA2※Norah Jones_?????????<CR>
NSA3※_????????????????????<CR>
NSA4※_????????????????????<CR>
NSA5※00:11
100%_???????<CR>
NSA6※_????????????????????<CR>
NSA7_????????????????????<CR>
NSA8_????????????????????<CR>
EVENT
PARAMETER
NSE
0
1
2
3
4
5
6
7
8
function
Onscreen Display Information(mServer/iRadio) is
Answered By the NSE Command.
Display Line1 Information
Display Line3 Information
Display Line4 Information
Display Line5 Information
Display Line6 Information
Display Line7 Information
Display Line8 Information
Display Line9 Information
Display Line10 Information
- 48 -
NSE0**************_?????<CR>
NSE1※************_?????<CR>
NSE2※************_?????<CR>
NSE3※************_?????<CR>
NSE4※************_?????<CR>
NSE5※************_?????<CR>
NSE6※************_?????<CR>
NSE7**************_?????<CR>
NSE8**************_?????<CR>
*:UTF-8 CODE Character(MAX96byte)
_:Null
?: Don't Care (The character after Null
should be disregarded)
※:Cursor&Playable Music
Information Data(1Byte)
Bit1:Playable Music =1
Bit2:Directory
Bit4:CURSOR SELECT=1
Bit7:Picture
Bit5,6,8:Don't Care
************_?????:96byte Fixed
<example>
NSE0Now Playing USB_????<CR>
NSE1※Come Away With Me_???<CR>
NSE2※Norah Jones_?????????<CR>
NSE3※_????????????????????<CR>
NSE4※_????????????????????<CR>
NSE5※00:11
100%_???????<CR>
NSE6※_????????????????????<CR>
NSE7_????????????????????<CR>
NSE8_????????????????????<CR>
※ iPod Extended Control
iPod Dock which AVR-4311 can connect with is ASD-1R/11R.
EVENT
PARAMETER
function
IPA
Onscreen Display Information is Answered
By the IPA Command.
0
Display Line1 Information
1
Display Line3 Information
2
Display Line4 Information
3
Display Line5 Information
4
Display Line6 Information
5
Display Line7 Information
6
Display Line8 Information
7
Display Line9 Information
8
Display Line10 Information
9
Display Line11 Information
IPA0***************_???<CR>
IPA1※*************_???<CR>
IPA2※*************_???<CR>
IPA3※*************_???<CR>
IPA4※*************_???<CR>
IPA5※*************_???<CR>
IPA6※*************_???<CR>
IPA7※*************_???<CR>
IPA8#**************_???<CR>
IPA9***************_???<CR>
*:Character Length MAX96
_:Null
?:Exclusion(The character after Null
should be disregarded)
※:Cursor Information Data(1Byte)
Bit1:Playable Music/Video=1
Bit2:Directory=1
Bit3:Don't Care
Bit4:CURSOR SELECT=1
Bit5,6,7,8:Don't Care
#:Bit1-8:Don’t Care
- 49 -
EVENT
PARAMETER
function
IPA
<example1>
IPA0Artist??????????????????<CR>
IPA1※ Ana Caram_????????????<CR>
IPA2※ Badi Assad_???????????<CR>
IPA3※ Christy Baron_????????<CR>
IPA4※ Marta Gomez_??????????<CR>
IPA5※ Rebecca Pidgeon_??????<CR>
IPA6※ Sara K_???????????????<CR>
IPA7※ Valerie Joyce_????????<CR>
IPA8# SFL Songs RPT All_???<CR>
IPA9 [
2/
6]_?????????<CR>
<example2>
IPA0Now Playing iPod_???????<CR>
IPA1※ A HARD DAY'S NIGHT._??<CR>
IPA2※ /The Beatles_?????????<CR>
IPA3※_??????????????????????<CR>
IPA4※ A HARD DAY'S NIGHT_???<CR>
IPA5※ 00:04_??????????????<CR>
IPA6※_??????????????????????<CR>
IPA7※_??????????????????????<CR>
IPA8# SFL Songs RPT All_???<CR>
IPA9????????????????????????<CR>
- 50 -
EVENT
PARAMETER
IPE
0
1
2
3
4
5
6
7
8
9
function
Onscreen Display Information(iPod) is Answered
By the IPA Command.
Display Line1 Information
Display Line3 Information
Display Line4 Information
Display Line5 Information
Display Line6 Information
Display Line7 Information
Display Line8 Information
Display Line9 Information
Display Line10 Information
Display Line11 Information
IPE0***************_???<CR>
IPE1※*************_???<CR>
IPE2※*************_???<CR>
IPE3※*************_???<CR>
IPE4※*************_???<CR>
IPE5※*************_???<CR>
IPE6※*************_???<CR>
IPE7※*************_???<CR>
IPE8#**************_???<CR>
IPE9***************_???<CR>
*:UTF-8 CODE Character(MAX96byte)
_:Null
?:Exclusion(The character after Null
should be disregarded)
※:Cursor Information Data(1Byte)
Bit1:Playable Music/Video=1
Bit2:Directory=1
Bit3:Don't Care
Bit4:CURSOR SELECT=1
Bit5-8:Don't Care
#:Bit1-8:Don’t Care
- 51 -
EVENT
PARAMETER
function
IPE
<example1>
IPE0Artist??????????????????<CR>
IPE1※ Ana Caram_????????????<CR>
IPE2※ Badi Assad_???????????<CR>
IPE3※ Christy Baron_????????<CR>
IPE4※ Marta Gomez_??????????<CR>
IPE5※ Rebecca Pidgeon_??????<CR>
IPE6※ Sara K_???????????????<CR>
IPE7※ Valerie Joyce_????????<CR>
IPE8# SFL Songs RPT All_???<CR>
IPE9 [
2/
6]_?????????<CR>
<example2>
IPE0Now Playing iPod_???????<CR>
IPE1※ A HARD DAY'S NIGHT._??<CR>
IPE2※ /The Beatles_?????????<CR>
IPE3※_??????????????????????<CR>
IPE4※ A HARD DAY'S NIGHT_???<CR>
IPE5※ 00:04_??????????????<CR>
IPE6※_??????????????????????<CR>
IPE7※_??????????????????????<CR>
IPE8# SFL Songs RPT All_???<CR>
IPE9_??????????????????????<CR>
- 52 -
※Remote Lock/Panel Lock
EVENT
SY
PARAMETER
REMOTE LOCK ON
REMOTE LOCK OFF
PANEL LOCK ON
PANEL+V LOCK ON
PANEL LOCK OFF
※UPGRADE ID Display
COMMAND
PARAMETER
UG
IDN ************
IDN NG
function
REMOTE CONTROL LOCK ON/OFF
PANEL BUTTON(Except MASTER VOL.)CONTROL LOCK ON
PANEL BUTTON & MASTER VOL. CONTROL LOCK ON
PANEL BUTTUM & MASTER VOL. CONTROL LOCK OFF
function
ID Number for UPGRADE is displayed on FL Display
************:12-digit ID Number
Can’t get ID number from DPMS
- 53 -
example
SYREMOTE LOCK ON<CR>
SYREMOTE LOCK OFF<CR>
SYPANEL LOCK ON<CR>
SYPANEL+V LOCK ON<CR>
SYPANEL LOCK OFF<CR>
example
UGIDN ************<CR>
UGIDN NG<CR>
Download PDF