D-MAX | Pixim Seawolf DSP | Instruction manual | D-MAX Pixim Seawolf DSP Instruction manual

Super Wide Dynamic Range
Dome Color Camera
사용 설명서 MANUAL
용 서
Pixim Seawolf DSP
The lightning flash with an arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated
dangerous voltage within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
INFORMATION - This equipment has been tested and found to comply with limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform
to all local codes
■ Warning
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time,
fire may be caused.
Do not install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in fire or other hazards.
1. Features
Our WDR camera is a superb wide dynamic range camera which achieves 120dB
max(102dB typical) of dynamic range of the image by implementing PIXIM's Seawolf
digital imaging system.
With Seawolf digital imaging system,
- Delivers high-resolution, crystal clear images that accurately capture every aspect of
any scene
- Offers the highest resolution of 690TVL(horizontal)
- Ultra-wide dynamic range imaging accurately captures all of the critical details in a
scene including highlights, shadows and everything in between without compromising
image quality or color accuracy.
- Enhanced low-light performance makes Seawolf the natural choices for both indoor
and outdoor cameras for all lighting conditions.
With ICR mechanism,
- Enhances its sensitivity about 10x at night time
- Can accepts the infrared light
Main features are;
• 1/3" CMY Color DPS SENSOR (Pixim Seawolf D8800C series)
• Resolution of 690 Horizontal Lines
• 10x sensitivity enhancement by removing the optical filter
• Switches to B/W and able to accept the infrared spectrum at night mode
• Enhanced sharpness compensation
• Very low noise and superior picture quality
• 0.0008Lux Class sensitivity (0.002Lux@ 2x Sense-up)
• Automatically removable IR Cut Filter
• Automatic White Balance (ATW)
• Built-in 2.8~10mm DC auto iris lens
2. Cable Connection and OSD Control
1) Cable Connection
2) OSD Control
② SETUP button : Used for the menu display. This button can be used to confirm
settings after changing the value of the selected function or current conditions.
③ UP & DOWN buttons : Used for selecting items by moving the cursor up or down on
the menu screen.
④ LEFT & RIGHT buttons : Used when changing item values, by moving the cursor to
the left or right on the menu screen
3. Setup Menu Operation
1) In the menu
Use ▲, ▼ buttons to move menu, ◀, ▶ buttons to change the settings and press
button
shortly to select or enter.
button stands for MENU or ENTER button.
2) Entering menu
Press
button longer than 2 sec on the back of camera.
3) MAIN
Follow below chart for submenu setting.
MENU
Default
Descriptions
Sets COLOR ROLL COMP., AE PREFERENCE, WDR CONTROL and
EXPOSURE
SENSE-UP.
Sets OFF, AUTO or NIGHT
OFF – Day/Night is disabled and camera works as a normal color camera.
DAY/NIGHT
AUTO
AUTO – Camera switches DAY from/to NIGHT automatically.
N->D THRES, N<->D DELAY, BURST ON B/W can be set.
See DAY&NIGHT AUTO SETUP for detail.
NIGHT – Forced to remove IR cut filter and switch to B/W.
3D NR
LENS
SELELT
Sets DEPTH of 3D NR.
DC
Selects the lens type, DC or MANUAL.
In sub-menu, Accurate Focus can be set by function of FOCUS ADJ…
PICTURE
Sets WHITE BALANCE, COLOR SELECT, SHARPNESS, SATURATION,
CONTROL
GAMMA.
SPECIAL
D-EFFECT
EXIT
Sets MOTION, PRIVACY MASK, SYNC, LANGUAGE, VIDEO STANDARD,
RS485 CONTROL.
Sets FREEZE, FLIP or D-PTZ.
Choose EXIT, SAVE AND EXIT or FACTORY SET.
4) EXPOSURE
To enter EXPOSURE menu, press
EXPOSURE
EXPOSURE
button at MAIN>EXPOSURE.
<WDR MID>
Descriptions
Descriptions
In NTSC system, the entire color tone on the monitor may continuously
Medium level of
the reddish
dynamicand
range
control for each PRESETs.
move
greenish.
WDR
HIGH
COLOR
Increases the COLOR
dynamic ROLL
range COMP.
control. -Some
highlight
arearolling
may washed
out.fluorescent
Reduces
the color
under the
CUSTOM...
ROLL
Provides
flexible compensation
other than WDR MID, WDR LOW, WDR HIGH
OFF morelighting.(NTSC
system only)
COMP.
BLC...
Default
Compensates OFF
the brightness
main objectthe
against
bright back light.
– Does notof
compensate
color the
rolling.
A zone out of CTR
SPOT,
UPPER1/3, MIDDLE1/3,
LOWER1/3
be set.
MODE-M
- Compensates
the color rolling
when a can
manual
lens is used.
Dynamic range
control is
inoperative if EXPOSURE
is set
to BLC.
MODE-A
- Compensates
the color rolling
when
an auto iris lens is used.
WDR LOW
AE
PREFRENCE
Decreases theSets
dynamic
range control.
HIGHLIGHTS
or SHADOWS
HIGHLIGHTS - Provides the best detail in the brighter areas.
HIGHLIGHTS
The darker parts of the scene may under-expose.
SHADOWS - Provides the best detail in the darker areas.
It will reduce the dynamic range and the brighter parts may overexpose.
LOW - Produces an image that has better contrast but less dynamic
range and is suitable for indoor or low-contrast outdoor scenes.
NORMAL - Produces an image that has average contrast and is suitable
for indoor or low-contrast outdoor scenes.
MEDIUM - Produces an image that has better dynamic range and is
WDR
CONTROL
MEDIUM
suitable for a lobby or high-contrast outdoor scenes.
HIGH - Produces an image that has best dynamic range but less
contrast and is suitable for high-contrast outdoor scenes.
CUSTOM - Provides more flexible compensation by ZONE, RANGE and
BIAS.
When COLOR ROLLCOMP. is set to MODE-A, WDR CONTROL will be
fixed as LOW.
If SENSE-UP is set to AUTO, the maximum sense-up
rate can be
limited to 2X-30FPS, 4X15FPS, 8X-18FPS, 16X-4FPS, 32X-2FPS or
64X-2FPS in SENSE-UP SETUP.
SENSE-UP
AUTO
The integration frames vary automatically within the max. rate according
to the light level when light becomes low and DSS is operating. The
higher sense-up rate, the higher sensitivity but the slower refresh rate.
Some white dots may appear by sense-up due to the image sensor’s
long accumulation by a long shutter period.
5) DAY/NIGHT
To enter EXPOSURE menu, press
button at MAIN>DAY/NIGHT>AUTO...
IMPORTANT!!!
IMPORTANT!!!
DAY->NIGHT and NIGHT->DAY operations must be examined and verified at the final step
of the installation.
Block the lens for a few seconds for NIGHT mode and release and let it return to DAY mode.
If camera stays at NIGHT mode more than 10sec, increase N-->D THRES a little and repeat
the fore-mentioned
steps.
DAY/NIGHT
Default
Descriptions
If the scene is too dim orN-->D
lens iris
was adjusted
too low(near
mayNIGHT
not return
to DAY.
THRES
is a threshold
level toclose),
switch itfrom
to DAY.
Due to the nature of WDR the image level of the scene is controlled down
N-->D
THRES.
and camera would not switch to DAY even though the ambient is bright
3
enough.
Increase the value if it stays in B/W and is required to switch to DAY.
Too high value may make ICR repeating between NIGHT<-->DAY.
In that case, reduce the value a little and try all of the above mentioned.
N<-->D DELAY is time in second while camera maintains its status before
N<-->D
DELAY
3
D<-->N switches.
DELAY can avoid the unwanted/frivolous switching by a short term lights
such like the light from the passing car.
BURST ON B/W determines whether a color burst signal keeps output or
eliminated when camera switches to B/W.
If set to ON, B/W video signal contains color burst signal and is more
BURST
ON
B/W
OFF
compatible with the color equipment but shows the same resolution as color
video.
If set OFF, the color burst signal is removed from B/W video and shows better
resolution.
Rarely the compatibility problem may occur with the color equipment.
6) 3D NR
To enter EXPOSURE menu, press
3D NR
button at MAIN>3D NR
Default
Descriptions
Determines the depth of Three Dimensional Noise Reduction.
DEPTH
47
High value reduces the noise strongly but the comet effect may occur
for the fast moving object and vice versa.
7) LENS SELECT
To enter EXPOSURE menu, press
DC/
MANUAL
button at MAIN>LENS SELECT>DC... or MANUAL...
Default
Descriptions
Lower value opens the lens iris and increases the brightness and vice
AI LEVEL
24
versa. Too high value reduces the amount of incoming light and may result
in a problem which camera does not return to DAY form NIGHT.
FOCUS ADJUST helps the Accurate focus adjustment regardless of DAY
FOCUS
ADJ...
-
or NIGHT. Sometimes the focus looks fine tuned at day time but out of
focus at night time. This function can eliminate the wrong adjustment of
focus in any case.
8) PICTURE CONTROL
To enter EXPOSURE menu, press
button at MAIN>PICTURE CONTROL.
PICTURE
PICTURE
Factory
Factory
CONTROL
PICTURE
CONTROL
Default
Factory
Default
CONTROL
Default
Descriptions
Descriptions
Descriptions
Sets
Sets ATW
ATW Normal,
Normal, ATW
ATW Desat,
Desat, ATW
ATW Xtnd
Xtnd or
or MANUAL.
MANUAL.
ATW
NORMAL
–– Compensates
automatically
in
Sets
Normal,
ATW Desat, ATW
Xtnd or MANUAL.
ATWATW
NORMAL
Compensates
automatically
in range
range of
of 2800K-7500K.
2800K-7500K.
WHITE
WHITE
ATW
DESAT
automatically
in
range
of
2000K-11000K.
ATW
– Compensates
automatically
range
2800K-7500K.
ATWNORMAL
DESAT –– Compensates
Compensates
automatically
inin
range
ofof
2000K-11000K.
ATW
ATW
BALANCE
WHITE
BALANCE
NORMAL
ATW
NORMAL
BALANCE
NORMAL
In
the
of
and
balance
ATW
– Compensates
automatically
in rangewhite
of 2000K-11000K.
InDESAT
the range
range
of 2000-2800K
2000-2800K
and 7500-11000K,
7500-11000K,
white
balance is
is
gradually
compensated.
In
the range
of 2000-2800K and 7500-11000K, white balance is
gradually
compensated.
ATW
Xtnd
gradually
compensated.automatically
ATW
Xtnd –– Compensates
Compensates
automatically in
in range
range of
of 2000K-11000K.
2000K-11000K.
MANUAL
balance
by
KELVIN
ATW
Xtnd –– White
Compensates
automatically
in range
of 2000K-11000K.
MANUAL
White
balance can
can be
be adjusted
adjusted
by either
either
KELVIN or
or R/B
R/B
COLOR
COLOR
SELECT
COLOR
SELECT
SELECT
MANUAL – White balance can be adjusted by either KELVIN or R/B
COLOR1
COLOR1 Provides
Provides three
three color
color tones.
tones.
COLOR1
Provides three color tones.
BRIGHTNESS
BRIGHTNESS level
level is
is aa kind
kind of
of video
video output
output gain
gain and
and is
is different
different from
from the
the
iris
ItIt can
be
to
MIDDLE,
HIGH
BRIGHTNESS
level
is
a kind
of video
output gain
and is MID-HIGH,
different
from
the
iris level
level control.
control.
can
be set
set
to MID-LOW,
MID-LOW,
MIDDLE,
MID-HIGH,
HIGH
BRIGHTNESS
BRIGHTNESS
and
LOW.
iris
control. It can be set to MID-LOW, MIDDLE, MID-HIGH, HIGH
andlevel
LOW.
BRIGHTNESS
IfIf itit is
set
and
LOW.
is
set too
too high,
high, the
the dynamic
dynamic range
range is
is decreased.
decreased.
or
sharpness
picture.
IfIncrease
it is set too
high, the the
dynamic
rangeof
isthe
decreased.
Increase
or decrease
decrease
the
sharpness
of
the
picture.
SHARPNESS
SHARPNESS
22
Too
can
make
harsh
and
Increase
orsharpness
decrease the
of the
picture.
Too much
much
sharpness
cansharpness
make image
image
harsh
and show
show more
more noise
noise
SHARPNESS
2
as
as
line
edge
of
in
Too
much
can
make
harsh
and
show more noise
as well
well
assharpness
line flicker
flicker at
at the
the
edgeimage
of object
object
in the
the picture.
picture.
SATURATION
SATURATION
11
as
well
as line
flicker
at the
of
object
in the picture.
High
value
makes
color
rich
and
versa.
High
value
makes
color
richedge
and vice
vice
versa.
SATURATION
1
High
value
makes
colorthe
richgain
andof
Lower
value
improves
the
dark
Lower
value
improves
the
gain
ofvice
theversa.
dark area
area but
but the
the image
image has
has less
less
GAMMA
GAMMA
45
45
GAMMA
45
9) SPECIAL
SPECIAL
contrast..
Lower
value improves the gain of the dark area but the image has less
contrast..
Higher
contrast..
Higher value
value reduces
reduces the
the gain
gain of
of the
the dark
dark area
area and
and makes
makes the
the image
image more
more
dark
contrastive.
image
will
loose
the
for
Higher
value
reduces The
the
of the
and
makes
the
image
more
dark and
and
contrastive.
Thegain
image
will dark
loosearea
the linearity
linearity
for too
too high
high value.
value.
dark and contrastive. The image will loose the linearity for too high value.
Default
MOTION
OFF
PRIVACY MASK
OFF
SYNC
INT1
LANGUAGE
VIDEO STANDARD
ENGLISH
NTSC
Descriptions
If it is set to ON and motion is detected, MOTION message will
appear on the monitor. See ‘7.9.1 MOTION ’ for settings.
If set to ON, it is available up to 6 privacy masks.
See ‘7.9.2 PRIVACY menu’ for settings.
Sync is fixed to INT1.
English is available only.
Able to switch NTSC or PAL.
① MOTION
Up to 4 motion areas and the sensitivity can be set. The sensitivity is applied for all zones equally.
In adjusting each zone, the zone border line changes color when pressing
button. Green enables
enlarging, red enables reducing and white enables moving the zone by ▼, ▲, ▲, ▼buttons.
To exit MOTION ZONE SETUP, press
button for 2 seconds.
② PRIVACY AREA
Up to 6privacy area can be programmed in size, position and mask color.
Use joystick to change size, position and mask color.
Right after pressing
button at ,ON..>, the
Right after one more pressing
button, the
1st zone appears on top-left corner in orange.
1st zone changes to blue.
The orange colored zone can be relocated in its
Blue colored zone can be resized with . ▼, ▲,
location with ▼, ▲, ▲, ▼ buttons.
▲, ▼ buttons
An example of mask when resizing by . ▼, ▲,
An example of mask when relocating.
▲, ▼ buttons
Press
button longer than 2 sec. to return to previous menu.
10) D-EFFECT
D-EFFECT
Default
FREEZE
OFF
Descriptions
Image freezes and shows the still image at the moment when set to ON..
OFF(Normal display), H-FLIP(left & right flipped), V-FLIP(upside down
FLIP
OFF
flipped), H/V-FLIP(left & right flipped and upside down flipped.)
Direction of joystick control should be flipped if V-flip is flipped to H/V-flip.
D-PTZ
Able to set digital zoom up to x12 and digital PAN/TILT if zoom ratio >1.
D-PTZ
Default
Descriptions
ZOOM
1
Digital zoom can set up to x12. x1 stands for ZOOM OFF.
PAN
0
Digital PAN can be set if ZOOM is set to >1.
TILT
0
Digital TILT can be set if ZOOM is set to >1.
11) EXIT
MENU-2
Descriptions
EXIT
Exits menu with discarding any changes.
SAVE AND EXIT
Exits menu after saving the parameters.
FACTORY SET
Restores and saves all parameters of factory settings.
Camera resets and restarts automatically.
If there are problems in operation, please refer to the items below. If the problem persists,
4. Troubleshooting
please contact the agent you purchased this product from.
Problems
Nothing appears on the screen.
Troubleshooting
• Please check the power connection.
• Please check the video signal line connection.
• Please check and make sure that the auto lens switch is
set to DC (VIDEO) when using a VIDEO(DC) lens.
The video image is not clear.
• Please check if the lens is clean.
Please clean the lens with a clean cloth or brush.
• Please adjust the contrast feature of the monitor.
• Please readjust the back focus of the camera.
The screen is dark.
• Please adjust the contrast feature of the monitor.
• If you have an intermediate device, set the 75 / Hi-z
properly, and check the terminals.
• Please check if an auto iris lens is being used and adjust
the brightness level.
There is a problem with the
camera operation.
• Please check if an appropriate power source to the
camera complies with the manufacturer's
standard requirement, or if the voltage keeps changing.
The MOTION DETECTION function
• Please check if 'MOTION DETECTION' mode is turned
is not working.
on.
• Please check if the MD LEVEL is too low.
• Please check the setting of the MD AREA.
Colors are not quite right.
• Please check the 'WHITE BAL' setting
The screen is flickering.
• Please check if the camera is facing directly into sunlight
or fluorescent light.
• Please check if an auto iris lens is being used.
• Please check the connection of the lens connector cable.
COLOR mode is not working.
• Please check if the AGC menu is set to the OFF
position.
SENS-UP function is not
• Please check if the AGC menu is set to the OFF
working.
position.
• Please check if the SHUTTER menu is set to
MANUAL mode.
5. Dimensions
6. Specifications
▪ GENERAL
Model name
NTSC
PAL
Image Device
1/3" CMY Color DPS SENSOR (Pixim Seawolf D8800C series)
Effective Pixels
768(H) x 540(V)
TV system
NTSC, 525lines / 2:1interlace
PAL, 625lines / 2:1interlace
Scan frequency.
59.94Hz(V), 15.734Khz(H)
50Hz(V), 15.625Khz(H)
Synchronization
Internal/Line lock (Default: Internal)
H. Resolution
690TV Lines
Sensitivity
0.0008Lux Class sensitivity (0.002Lux@ 2x Sense-up)
S/N Ratio
52dB with AGC OFF at 50IRE
White Balance
2000~11000ºK Automatic tracking
WDR Mode
(Low/Middle/High/Custom(User adjustment))
Auto Iris Control
DC drive iris control. Level control is fixed internally.
SENSE-UP
2X, 4X, 8X, 16X, 32X, 64X ESS
Motion Detection
On/Off(4 Programmable Zone)
D-PTZ
Up to X12 digital zoom
FLIP
OFF / H-FLIP / V-FLIP / H/V-FLIP
Privacy Zone
On/Off (6 Programmable Zone)
Auto Iris Control
DC Drive Iris Control
Flicker reduction
Yes (NTSC Japanese version only)
OSD
Yes (Setup menu only)
Video Output
VBS 1Vpp +/-10%, 75ohm
2.8-10mm DC auto iris lens □
Lens
2.8-12mm DC auto iris lens □
mm □,
Operating Power
mm DC auto iris lens □
DC 12V (10.2-14.5V)
Dual Voltage(DC12V/AC24V):Optional
Power consumption
230mA
Operating condition
-10ºC~+50ºC, 30~90% RH
▪ DOME CASE
Dome Type
Install Type
Dimension(mm)
3 Axis
Material
Weight
Indoor
Outdoor(IP66)
Outdoor(IP66)
100(Bubble) x 139.5(H)
100(Bubble) x 103(H)
100(Bubble)x 107.5(H)
3 Axis
3 Axis
3 Axis
Plastic Body,
PC Bubble,
PC Bubble,
PC Bubble
Aluminum Body
Aluminum Body
560g
1.1Kg
1.1Kg
19
Download PDF