Dimplex | SF3003 | Owner`s manual | Dimplex SF3003 Owner`s manual

Owner’s Manual
Model Numbers:
DF3003
DFB6016
Quality checked by:
Serial Number
Model Number
Part Number
Valued Customer,
Thank you and congratulations for purchasing a Dimplex
electric fireplace. Over the years, valuable memories
will occur around the warmth and comfort of your
fireplace. Thank you for allowing our product to be the
backdrop for those special moments.
7205450200R10
QUICK REFERENCE GUIDE
1. Prior to the first use of the fireplace verify the
following:
• Are the circuit breakers for the unit on?
• Are the light bulbs in your fireplace loose? (to
check, follow the instructions for replacing
the light bulbs under the Maintenance
section of this manual)
2. The heater on your fireplace may emit a slight,
harmless odor when first used. This odor is a
normal condition caused by the initial heating of
internal heater parts and will not occur again.
3. The information regarding the model of your
fireplace can be found on the rating plate
located on the top of the unit.
4. If you have any technical questions or concerns
regarding the operation of your fireplace, or
require service contact Dimplex North America
customer service at 1-888-DIMPLEX
(1-888-346-7539) before returning the product
to the point of purchase.
2
CONTENTS
PAGE 4 Important Instructions
PAGE 6 Model and Serial Number
Information PAGE 7
Site Selection and Preparation
PAGE 10 Fireplace Insert Installation
PAGE 11 Operation
PAGE 14
Maintenance
PAGE 17
Warranty
3
IMPORTANT INSTRUCTIONS
Please Retain This User’s Guide For Future Reference
When using electrical appliances, basic precautions should always be followed
to reduce the risk of fire, electric shock, and injury to persons, including the
following:
1. Read all instructions before using the electric fireplace.
2.
The heater is hot when in use. To avoid burns, do not let bare skin touch
hot surfaces. The trim around the heater outlet becomes hot during heater
operation. Keep combustible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at least three (3) feet (0.9 m) from
the front of the unit.
3. Extreme caution is necessary when any heater is used by or near children
or invalids and whenever the unit is left operating and unattended.
4. Always unplug the electric fireplace when not in use.
5.
Do not operate any unit with a damaged cord or plug, or if the heater has
malfunctioned, or if the electric fireplace has been dropped or damaged in
any manner. Return heater to authorized service facility for examination,
electrical or mechanical adjustment, or repair. 6. Do not use outdoors.
7. The electric fireplace is not intended for use in bathrooms, laundry areas
and similar indoor locations. Never locate heater where it may fall into a
bathtub or other water container.
8. Do not run the cord under carpeting. Do not cover cord with throw rugs,
runners, or the like. Arrange cord away from traffic area and where it will
not be tripped over.
9. To disconnect the unit, turn the controls off, then remove the plug from the
outlet.
10.Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage to the
heater.
11.To prevent a possible fire, do not block air intake or exhaust in any
manner. Do not use on soft surfaces, like a bed, where openings may
become blocked.
12.All electrical heaters have hot and arcing or sparking parts inside. Do not
use in areas where gasoline, paint, or flammable liquids are used or stored
or where the unit will be exposed to flammable vapors.
13.Do not modify the electric fireplace. Use it only as described in this
manual. Any other use not recommended by the manufacturer may cause
fire, electric shock or injury to persons.
4
14.Avoid the use of an extension cord. Extension cords may overheat and
cause a risk of fire. If you must use an extension cord, the cord must be
No. 14 AWG minimum size and rated no less than 1875 Watts.
15.Do not burn wood or other materials in the electric fireplace.
16.Do not strike the fireplace glass.
17.Always use a certified electrician should new circuits or outlets be required.
18.Always use properly grounded, fused and polarized outlets.
19.Disconnect all power supply before performing any cleaning, maintenance
or relocation of the unit.
20.When transporting or storing the unit and cord, keep in a dry place, free
from excessive vibration and store so as to avoid damage.
21.WARNING: To prevent overheating, do not cover heater.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
SAVE THESE INSTRUCTIONS
! NOTE: Procedures and techniques that are considered important enough
to emphasize.
CAUTION: Procedures and techniques which, if not carefully followed, will
result in damage to the equipment.
WARNING: Procedures and techniques which, if not carefully followed, will
expose the user to the risk of fire, serious injury, illness or death.
! NOTE: This equipment has been tested and found to comply with the
limits for Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and the receiver.
· Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
5
· Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions: (1) this device may not
cause interference and; (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Model and Serial Number Information
If you have any questions about our products please have the product
model and serial numbers available upon calling Dimplex customer
service. To locate the model and serial number labels see below
(figure 1).
Figure 1
Model Number
Serial Number
Model
Number
Label
Model
Number
Label
Serial
Number
Label
Serial
Number
Label
Firebox
Carton
6
Site Selection and Preparation
This section provides easy step by step instructions for selecting a
location and preparing the site to install the fireplace into:
• Existing fireplace
• New wall construction
• Dimplex mantel surround kit or custom made mantel surround
! NOTE: A 15 Amp, 120 Volt circuit is required. A dedicated circuit
is preferred but not essential in all cases. A dedicated circuit will
be required if, after installation, the circuit breaker trips or fuse
blows on a regular basis when the heater is operating. Additional
appliances on the same circuit may exceed the current rating of the
circuit breaker.
WARNING: Ensure the power cord is not installed so that it is
pinched or against a sharp edge and ensure that the power cord is
stored or secured to avoid tripping or snagging to reduce the risk of
fire, electric shock or injury to persons.
Construction and electrical outlet wiring must comply with local
building codes and other applicable regulations to reduce the risk of
fire, electric shock and injury to persons.
Do not attempt to wire your own new outlets or circuits. To reduce
the risk of fire, electric shock or injury to persons, always use a
licensed electrician.
! NOTE: The fireplace insert comes completely assembled and
wired. Some tools may be required to prepare the site and
assembly/install the trim.
The dimensions of the fireplace insert are 30 1/4 inch (76.8 cm)
wide X 25 1/2 inch (64.8 cm) high X 11 1/2 inch (29.2 cm) deep
(Figure 2). You should allow 1/4 inch (6.4 cm) around the fireplace insert for
ease of installation. This fireplace does not require any venting.
CAUTION: Clearance for air circulation beneath the fireplace insert
is provided by four (4) rubber feet (Figure 2). Do not install the
fireplace insert directly on carpet or similar surfaces which
7
Figure 2
30 1/4” (76.8 cm)
25 1/2”
(64.8 cm)
Rubber
Feet
11 1/2”
(29.2 cm)
Air Circulation Areas
may restrict air circulation. If installing the fireplace in a carpeted
area, place a one-piece, solid, flat surface under the fireplace insert. Ensure that all four of the insert’s feet rest securely on this surface.
Existing Fireplace Installation
1. Seal all drafts and vents with non-fibrous insulation materials to
prevent chimney debris from falling into the fireplace insert. Do not
install into an existing fireplace that is prone to leaks or dampness.
2. Cap the top of the chimney flue to prevent rain from entering.
3. Plan your electrical power supply (refer to NOTE 1).
4. The power cord can run along the front of the hearth to an outlet
near the fireplace.
! NOTE 1: A 15 Amp, 120 Volt circuit is required. A dedicated circuit
is preferred but not essential in all cases. A dedicated circuit will
be required if, after installation, the circuit breaker trips or fuse
blows on a regular basis when the heater is operating. Additional
appliances on the same circuit may exceed the current rating of the
circuit breaker.
8
WARNING: To prevent personal injury you should hire a
professional to cap the chimney flue or cut a hole in the existing
fireplace for wiring. If you return your existing fireplace to its
original use (example: wood burning), it should be inspected by the
local building department prior to use to reduce the risk of fire and
personal injury.
New Wall Construction
1. Select a suitable location that is not susceptible to moisture and is
away from drapes, furniture and high traffic.
2. Place the fireplace in the desired location to see how it will look in
the room.
3. Mark the desired location on the floor and store the fireplace in a
safe, dry and dust free location.
4. Use studs to frame an opening of 30 3/4 inch (78.1 cm) wide X 25
3/4 inch (65.4 cm) high X 11 3/4 inch (29.8 cm) deep (Figure 3).
5. Plan your electrical power supply (refer to NOTE 1).
Figure 3
25 3/4”
(65.4 cm)
30 3/4”
(78.1 cm)
11 3/4”
(29.8 cm)
9
Option #1 - The power cord can be lead from behind the trim and along the wall to an outlet near the fireplace.
Option #2 - A new outlet can be installed inside the new frame
construction.
Dimplex Mantel Surround Kit or Custom Made Mantel
Surround
1. Select a suitable location that is not susceptible to moisture and is
away from drapes, furniture and high traffic.
2. Place the fireplace in the desired location to see how it will look in
the room.
3. For ease of electrical hook up you may wish to locate the fireplace
near an existing outlet (refer to NOTE 1).
4. Store the fireplace in a safe dry and dust free location.
5. Assemble the mantel surround kit (refer to the mantel assembly
instructions) or construct the custom surround with an opening of
30 3/4 inch (78.1 cm) wide X 25 3/4 inch (65.4 cm) high X 11 3/4
inch (29.8 cm) deep (Figure 3).
WARNING: Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always
use a licensed electrician.
Fireplace Insert Installation
1. Make sure the unit’s Main ON/OFF switch is switched OFF (refer to
operating instruction section).
2. Plug the unit into a 15 Amp/120 Volt outlet. If the cord does not
reach, you may use an extension cord rated for a minimum of 1875
Watts.
3. Push the fireplace into the opening being careful not to damage the
base of the mantel or cabinet so that the fireplace is flush with the
mantel or cabinet.
4. Level the unit with shims if necessary (not provided).
5. Install the trim onto the fireplace (refer to trim installation
instructions).
10
WARNING: Ensure the power cord is not installed so that it is
pinched or against a sharp edge and ensure that the power cord is
stored or secured to avoid tripping or snagging to reduce the risk of
fire, electric shock or injury to persons.
Operation
Electric Fireplace Manual Controls (Figure 4)
Figure 4
D
B
C
A
A. Manual on/off Switch
The fireplace has a manual power ON/OFF switch located on the
control panel of the fireplace. To operate press the switch once, to turn
the unit on. Press the switch again to turn the unit off.
B. Light Dimmer
Turn the flame brightness control knob to increase or decrease the
brightness of the flame and embers.
C. Flame Action Control
Turn the flame action control knob to adjust the flame speed control to
the desired level.
D. Manual Selection Switch (Figure 4, 5)
Operates the electric fireplace manually. Pressing the switch up
(“
“ position) once turns on the electric fireplace and activates Level
1, twice activates Level 2, three times activates Level 3. Pressing the switch down (“
“ position) turns the electric fireplace
OFF.
11
Figure 5
Level 1 Indicator
Level 2 Indicator
Level 3 Indicator
Level 1: The flame effect is turned on and the first red indicator light
illuminates.
Level 2: The flame effect remains on, the heater is activated to
the low heat setting, and the first and second red indicator lights
illuminate.
Level 3: The flame effect remains on, the heater is set to the high heat
setting, and all three red indicators illuminate.
Resetting the Temperature Cutoff Switch
Should the heater overheat, an automatic cut out will turn the heater
off and it will not come back on without being reset. It can be reset by
switching the Main ON/OFF Switch to OFF and waiting five (5) minutes
before switching the unit back on.
CAUTION: If you need to continuously reset the heater, unplug the
unit and call Dimplex North America Limited at 1-888-346-7539.
Remote Control
The fireplace is supplied with a radio frequency remote control. This
remote control has a range of approximately 50 feet (15.25 m), it
does not have to be pointed at the fireplace and can pass through
most obstacles (including walls). It is supplied with one of 2,178
independent frequencies to prevent interference with other units. The
frequency designation is indicated on the back of the transmitter.
Remote Control Initialization
Follow steps 1 through 6 to initialize your fireplace for the first time. This procedure is also required every time there is a loss of power to
the remote control in the fireplace (I.E. power failure, breaker tripped,
main power switch is turned off).
12
1. Ensure that power is supplied through the
main service panel.
2. Access the manual controls, (remove glass
doors or pull grill down if applicable) pull the
right side steel curtain to the outside of the
unit (if applicable).
3. Locate manual controls.
4. Activate main power switch.
5. Press and hold the ON switch marked “
”
for five (5) seconds (red indicator light will
flash).
6. Press the ON button located on the remote
control transmitter. Figure 6
OFF
Button
ON
Button
This will synchronize the remote control
transmitter and receiver.
Remote Control Usage
The remote control operates the fireplace levels
sequentially. The level is increased every time
the ON button on the transmitter is pressed. The fireplace can be turned off at any point by
pressing the OFF button on the remote control
transmitter.
Level 1: The flame effect is turned on and the
Battery
first red indicator light illuminates.
Cover
Level 2: The flame effect remains on, the
heater is activated to the low heat setting,
and the first and second red indicator lights
illuminate.
Level 3: The flame effect remains on, the heater is set to the high heat
setting, and all three red indicators illuminate.
Battery Replacement (Figure 6)
To replace the battery:
1. Slide battery cover open on the hand held transmitter. 13
2. Correctly install one 12 Volt (A23) battery in the battery holder.
3. Close the battery cover.
Maintenance
WARNING: Disconnect power before attempting any maintenance
or cleaning to reduce the risk of fire, electric shock or damage to
persons.
Required tools: Phillips #2 screw driver, Slot screw driver
Approximate time: 15 minutes to change upper and lower light bulbs.
Light Bulb Replacement
Allow at least five (5) minutes for light bulbs to cool off before touching
bulbs to avoid accidental burning of skin. Light bulbs need to be
replaced when you notice a dark section of the flame or when the
clarity and detail of the log exterior disappears. There are four (4)
bulbs under the log set which generate the flames and embers and
two (2) bulbs up, in behind the grill that illuminate the interior of the
fireplace.
To open the light bulb area:
1. Remove the trim by turning the retaining
fasteners counterclockwise 1/4 turn until
the trim releases from the firebox using a
slotted screwdriver (Figure 7).
2. Hold the glass in place while removing the
retaining clip from the upper center of the
firebox (Figure 8A, B).
3. Lift glass out and store in a safe place.
Figure 7
Lower Light Bulb Requirements
Quantity of four (4) clear chandelier or candelabra bulbs with an E-12
(small) socket base, 60 Watt rating.
To replace the bottom light bulbs:
1. Lift up the front edge of the log until it clears the front tabs. Pull out
14
Figure 8
A
2.
3.
4.
5.
Removing
Glass
B
Holding
Glass
Retaining
Clip
until the rear tab clears the back ledge, then lift out (Figure 9).
Examine the bulbs to determine which bulbs require replacement.
Hold the socket while unscrewing the bulb.
Hold the socket while screwing in the new bulb.
Replace the log ember bed by placing the back lip of the log ember
bed under the mirror then push the front of the log ember bed down
into the recess (Figure 9).
Upper Light Bulb Requirements
Quantity of two (2) clear chandelier or candelabra bulbs with an E-12
(small) socket base, 15 Watt rating.
Figure 9
Figure 10
Back
Ledge
Rear
Tab
Log
Ember
bed
Side Section
To replace the top light bulbs:
1. Locate the two upper bulbs inside the firebox at the top (Figure 10).
2. Examine the bulbs to determine which bulbs require replacement.
15
3. Hold the socket while unscrewing the bulb.
4. Hold the socket while screwing in the new bulb.
Helpful Hints
It is a good idea to replace all light bulbs at one time if they are close to
the end of their rated life. Group replacement will reduce the number
of times you need to open the unit to replace light bulbs.
Glass Cleaning
The glass is cleaned in the factory during the assembly operation. During shipment, installation, handling, etc., the clear door may collect
dust particles, these can be removed by dusting lightly with a clean dry
cloth.
To remove fingerprints or other marks, the clear door can be cleaned
with a damp cloth. The clear door should be completely dried with a
lint free cloth to prevent water spots. To prevent scratching, do not use
abrasive cleaners or spray liquids on the clear door surface.
Fireplace Surface Cleaning
Use a cloth dampened with warm water only to clean painted surfaces
of the electric fireplace. Do not use abrasive cleaners.
16
Five Year Limited Warranty
Products to which this limited warranty applies
This limited warranty applies to the following applicable models of your newly purchased
Dimplex electric fireplace SF3003, EF3003, DF3003, DFB6016 and to newly purchased
Dimplex fireplace surrounds (mantels) and trims. This limited warranty applies only to
purchases made in any province of Canada except for Yukon Territory, Nunavut, or
Northwest Territories or in any of the 50 States of the USA (and the District of Columbia)
except for Hawaii and Alaska. This limited warranty applies to the original purchaser of
the product only and is not transferable.
Products excluded from this limited warranty
Light bulbs are not covered by this limited warranty and are the sole responsibility of the
owner/purchaser. Products purchased in Yukon Territory, Nunavut, Northwest Territories,
Hawaii, or Alaska are not covered by this limited warranty. Products purchased in these
States, provinces, or territories are sold AS IS without warranty or condition of any kind
(including, without limitation, any implied warranties or conditions of merchantability or
fitness for a particular purpose) and the entire risk of as to the quality and performance
of the products is with the purchaser, and in the event of a defect the purchaser assumes
the entire cost of all necessary servicing or repair.
What this limited warranty covers and for how long
Products, other than fireplace surrounds (mantels) and trims, covered by this limited
warranty have been tested and inspected prior to shipment. Subject to the provisions
of this warranty, Dimplex warrants such products to be free from defects in material and
workmanship for a period of 5 years from the date of the first purchase of such products
as follows: (a) a repair or replacement warranty on defective products or parts, including
in-home services, for the first two years following the date of first purchase; and (b)
thereafter, a replacement of parts warranty on defective products and parts (with no
in-home services) for the 3 year period commencing on the second anniversary of first
purchase and ending on the fifth anniversary of the date of first purchase.
Dimplex fireplace surrounds (mantels) and trims covered by this limited warranty
have been tested and inspected prior to shipment and, subject to the provisions of
this warranty, Dimplex warrants such products to be free from defects in material and
workmanship for a period of 1 year from the date of first purchase of such products. Warranty services do not include in-home services. The above section is a summary only of your warranty rights. Please review the
remaining provisions of this warranty for your specific rights.
The limited 5 year warranty period for products other than fireplace surrounds (mantels)
and trims and the limited 1 year warranty period for fireplace surrounds (mantels) and
trims also applies to any implied warranties that may exist under applicable law. Some
jurisdictions do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to the purchaser.
What this limited warranty does not cover
This limited warranty does not apply to products that have been repaired (except by
17
Dimplex or its authorized service representatives) or otherwise altered. This limited
warranty does further not apply to defects resulting from misuse, abuse, accident,
neglect, incorrect installation, improper maintenance or handling, or operation with an
incorrect power source.
What you must do to get service under this limited warranty
Defects must be brought to the attention of Dimplex Technical Service by contacting
Dimplex at 1-888-DIMPLEX (1-888-346-7539), or 1367 Industrial Road, Cambridge
Ontario, Canada N1R 7G8. Please have proof of purchase, catalogue/model and serial
numbers available when calling. Limited warranty service requires a proof of purchase
of the product.
What Dimplex will do in the event of a defect
In the event a product or part covered by this limited warranty is proven to be defective in
material or workmanship during (i) the 5 year limited warranty period for products other
than fireplace surrounds (mantels) and trims, and (ii) the 1 year limited warranty period
for surrounds (mantels) and trims, you have the following rights: • Limited warranty service will be performed solely by dealers or service agents of
Dimplex authorized to provide limited warranty services.
• For products (other than surrounds (mantels) and trims) for the period ending
at midnight on the second anniversary of the date of first purchase, Dimplex will
in its sole discretion either repair or replace such defective product or part without
charge. If Dimplex is unable to repair or replace such product or part, or if repair or
replacement is not commercially practicable or cannot be timely made, Dimplex may,
in lieu of repair or replacement, choose to refund the purchase price for such product
or part. This limited warranty entitles the purchaser to on-site or in-home warranty
services. Accordingly, Dimplex will be responsible for all labour and transportation
costs associated with the repair or replacement of the product or part, except as
follows: (i) charges may be levied for travel costs incurred to travel to the purchaser’s
site where the product is located if the purchaser’s site is beyond 30 miles (48 km)
from the closest service depot of Dimplex’s dealer or service agent; and (ii) the
purchaser is solely responsible for providing clear access to all serviceable parts of
the product.
• For products (other than surrounds (mantels) and trims) for the period
commencing at 12:01 a.m. on the day after the second anniversary of the
first purchase and ending at midnight on the fifth anniversary of the date of
first purchase, this limited warranty entitles the purchaser to replacement parts
only without charge. If Dimplex is unable to replace such part, or if replacement
is not commercially practicable or cannot be timely made, Dimplex may, in lieu of
replacement, choose to refund the purchase price for such part. The purchaser
shall not be entitled to on-site or in-home warranty services. The purchaser shall be
responsible for all expenses incurred for the removal of the part and installation of the
replacement part including, without limitation, all shipping costs and transportation
costs to and from the authorized dealer’s or service agent’s place of business and all
labour costs. Such costs shall not be the responsibility of Dimplex.
• For surrounds (mantels) and trims for the period ending at midnight on the first
anniversary of the date of first purchase, Dimplex will in its sole discretion either
18
repair or replace such defective surrounds (mantels) and trims or part thereof without
charge. If Dimplex is unable to repair or replace such product or part, or if repair or
replacement is not commercially practicable or cannot be timely made, Dimplex may,
in lieu of repair or replacement, choose to refund the purchase price for such product
or part. The purchaser shall not be entitled to on-site or in-house services. The
purchaser is responsible for all expenses incurred for repair or replacement of such
product or part including, without limitation, all shipping costs and transportation costs
to and from the authorized dealer’s or service agent’s business and all labour costs. Such costs shall not be the responsibility of Dimplex.
• On-site or in-home services not provided under this warranty may be performed at
the purchaser’s specific request and expense at Dimplex’s then-current rates for such
services.
What Dimplex and its dealers and service agents are also not responsible for
IN NO EVENT WILL DIMPLEX, OR ITS DIRECTORS, OFFICERS, OR AGENTS, BE
LIABLE TO THE PURCHASER OR ANY THIRD PARTY, WHETHER IN CONTRACT,
IN TORT, OR ON ANY OTHER BASIS, FOR ANY INDIRECT, SPECIAL, PUNITIVE,
EXEMPLARY, CONSEQUENTIAL, OR INCIDENTAL LOSS, COST, OR DAMAGE
ARISING OUT OF OR IN CONNECTION WITH THE SALE, MAINTENANCE, USE,
OR INABILITY TO USE THE PRODUCT, EVEN IF DIMPLEX OR ITS DIRECTORS,
OFFICERS, OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
LOSSES, COSTS OR DAMAGES, OR IF SUCH LOSSES, COSTS, OR DAMAGES ARE
FORESEEABLE. IN NO EVENT WILL DIMPLEX, OR ITS OFFICERS, DIRECTORS,
OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES, COSTS, OR DAMAGES THAT
EXCEED THE PURCHASE PRICE OF THE PRODUCT.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO THE PURCHASER.
How State and Provincial law apply
This limited warranty gives you specific legal rights, and you may also have other
rights which vary from jurisdiction to jurisdiction. The provisions of the United Nations
Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or
the sale of products covered by this limited warranty.
Dimplex North America Limited
1367 Industrial Road Cambridge ON
Canada N1R 7G8
© 2009 Dimplex North America Limited
1-888-346-7539 www.dimplex.com
19
Download PDF