Vertical | FX Series | Specifications | Vertical FX Series Specifications

98/99™
Series
Exit devices
Introduction
Exit devices are a critical part of the fire and life safety egress system and will provide safe and
reliable service when properly applied and maintained. Von Duprin designs and manufactures
exit devices in accordance to ISO 9001 Quality Management System and meets or exceeds
accepted U.S. domestic and International standards. All 98 and 99 Series exit devices are UL
listed for panic hardware or fire hardware, and are certified to ANSI A156.3, 2001, Grade 1. Many
models are also certified for Hurricane Resistant Applications. Consult your local Security &
Safety consultant (SSC) or the Von Duprin factory for current listings.
It is intended that the information included in this publication, when properly used, will provide
clear and reliable guidelines to the proper general selection and application. However, the
scope of the information is necessarily limited.
98 Series features smooth mechanism case.
99 Series features grooved mechanism case.
Von Duprin exit devices are available in two external surface styles, designated 98 and 99 Series.
The Quiet One®
A fluid damper decelerates the
pushpad on its return stroke and
eliminates most noise associated
with exit device operations.
Furnished on all 98/99™ Series
exit devices.
VON DUPRIN
Administrative Offices
2720 Tobey Dr.
Indianapolis, IN 46219
2 • Von Duprin 98/99 Series
Customer Service
877-671-7011
800-999-0328 - Fax
Latch bolt
Deadlocking latchbolt provides security and
improved performance at standard device cost.
Technical Support
877-671-7011
Table of contents
Exit hardware
Fire exit hardware
Rim devices
Rim devices
98/99E
8
98-F/99E-F
10
Trim
9
Trim
11
Mortise lock devices
Mortise lock devices
875/9975
12
9875-F/9975-F
14
Trim
13
Trim
15
Surface mounted
Vertical rod devices
Surface mounted
Vertical rod devices
9827/9927
16
9827-F/9927-F
18
Trim
17
Trim
19
Three-point latching devices
Three-point latching devices
9857/9957
20
9857-F/9957-F
22
Trim
21
Trim
23
Concealed vertical
rod devices
Concealed vertical
rod devices
9847/9947
24
9847-F/9947-F
26
Trim
25
Trim
27
9848/9948
28
9848-F/9948-F
30
Trim
29
Trim
31
Concealed vertical
cable devices
Concealed vertical
cable devices
9849/9949
32
9849-F/9949-F
34
Trim
33
Trim
35
Wood door concealed
vertical rod devices
Wood door concealed
vertical rod devices
9847WDC/9947WDC
36
9847WDC-F/9947WDC-F
38
Trim
37
Trim
39
Wood door concealed
vertical cable devices
Wood door concealed
vertical cable devices
9849WDC/9949WDC
40
9849WDC-F/9949WDC-F
42
Trim
41
Trim
43
9850WDC/9950WDC
44
9850WDC-F/9950WDC-F
46
Trim
45
Trim
47
Be sure to ask your SSC representative to tell you about Custom Solutions
by Ingersoll Rand Security Technologies. To learn more visit securitytechnologies.allegion.com.
Von Duprin 98/99 Series • 3
Options and accessories
Applications
& trim
operation
Single & double door applications
Door handing
outside trim operation
Lever styles
Trim
options
Knob
Thumbpiece
Lever
Electrified outside lever trim (E996L)
Breakaway lever
Thumbturn control
Hospital pull
Offset pull
Vandal resistant pull
AD-Series adaptable electronic trim
Strike
options
Strike/Stile information
Strikes
Dogging
options
Cylinder dogging
Hex key dogging
Less dogging
Dogging keys
Special center case dogging
Double cylinder
Electrical
options
RX Request to exit
LX Latchbolt monitoring
SS Signal switch
CX Chexit®
ALK Alarm kit
Electric mortise lock device
EL Electric latch retraction
QEL Quiet electric latch retraction
CON Allegion Connect
Electrical
accessories
Power supplies
Electric power transfer
Mechanical
options
XP98/99 rim exit device
WS Surface vertical rod exit device
Less bottom rod
AX Accessible device
Pullman latch
Dummy push pad
Braille, embossed, knurled and safety glow
(Luminescent) touchpads
Pneumatic
options
Pneumatic controlled exit devices
Pneumatic power transfer
Device
accessories
Glass bead kit
Vertical rod and latch guard
Cover plate kits
Cylinders
Mullions
Sex bolts
Additional
information
ANSI Function, grade & type
Ul fire labeling and opening size
Finishes
Standard & special finishes
Symbols
Indicates fire rated application
Indicates ADA products
C o n t i n u i n g c o m m i t m e n t t o q u a l i t y.
4 • Von Duprin 98/99 Series
Nomenclature – how to order
EL
None
SD
CD
CX
E
QEL
EL
LX
RX
RX2
SS
AX
Standard
Special dogging R/VR - panic only
Cylinder dogging - panic only
Chexit
Electric locking mortise/lever
Quiet electric latch retraction
Electric latch retraction
Latch bolt monitoring
Request to exit
Double request to exit
Signal switch
Accessible device
PL
PN
WS
XP
Pullman latch
Pneumatic latch retraction
Surface vertical rod exit device
Heavy protection - rim
WS
Tornado & hurricane tested
98
99
Series 98-smooth
Series 99-grooved
None
27
47
47WDC
48
49
49WDC
57
75
Rim device
Surface mounted vertical rod device
Concealed vertical rod device
Concealed vertical rod wood door device
Concealed vertical rod device
Concealed vertical cable device
Concealed vertical cable wood door device
Three-point latch device
Mortise lock device
XX
DT
EO
HL
K
K-BE
K-DT
K-NL
L
L-BE
L-DT
L-NL
NL
NL-OP
TL
TL-BE
TP
TP-BE
AD Trim (to come from client)
Dummy trim
Exit only
Hospital pull trim
Knob
Knob - blank escutcheon
Knob, rigid - dummy trim
Knob, rigid - night latch
Lever (classroom)
Lever - blank escutcheon
Lever, rigid - dummy trim
Lever, rigid - night latch
Night latch
Night latch cylinder assembly, optional pull
Turn lever
Turn lever - blank escutcheon
Thumbpiece
Thumbpiece - blank escutcheon
XX
Lever style 06 standard
Optional 01, 02, 03, 05, 07, 12 (Handed),
16 (Omega), 17, 18, Accent, Asti, Merano, St. Annes
F
Fire exit device
-2
Double cylinder (rim & mortise only)
LBR
LBL
SG
ALK
ALK-AR1
ALK-AR3
ALK-AR6
CON
Less bottom rod
Less bottom latch
Safety glow (luminescent) touchpad
Alarm kit
Auto-reset 1 1 /2 minute alarm kit
Auto-reset 3 minute alarm kit
Auto-reset 4 1 /2 minute alarm kit
Allegion Connect
2'
3'
4'
2' Device (2' door size) 27, 47 or 49 only
3' Device (2' 4"– 3' door size)
4' Device (2' 10"– 4' door size)
Finishes
US3, US4, US10, US26, US26D, US28, 313, 315
US32D – 98 ONLY
-AM Antimicrobial (available US26D and US32D)
-LHR
-RHR
Left hand reverse
Right hand reverse
99
27
-L
-16
-F
LBR
3'
US3 RHR
Von Duprin 98/99 Series • 5
Popular double door applications
Single door applications
Double door applications
Mortise lock and surface mounted or
concealed vertical cable/rod device
combination—same direction
Single rim device
Single mortise
lock device
Two rim devices with mullion—
same direction
Two vertical rods—double egress
Door handing
Left hand-reverse
Left Hand-Reverse
orientation
Right hand-reverse
Right Hand-Reverse
orientation
Orientation
Orientation
LHR
RHR
hand reverse)
(Left(Left
hand-reverse)
(Right
hand reverse)
(Right
hand-reverse)
Outside
Two surface mounted vertical rod
devices—same direction (do not use
with overlapping astragal)
Outside
Two fire exit hardware vertical
cables/rods with auxilary fire
latch-LBR option
Two concealed vertical cables/rods
Outside trim operation
Trim operation lever or knob
Standard
Night latch
Blank escutcheon
Dummy
Key locks and unlocks lever or knob. e.g.,
996L (Classroom)
Key retracts latch bolt. Lever or knob
is rigid. Use NL suffix, e.g. 996LNL.
(Storeroom)
Lever or knob always active. Use BE
suffix, e.g., 996L-BE. (Passage)
Lever or knob rigid for pull
operation. Use DT suffix, e.g.,
996L-DT.
996L Breakaway™ lever
The 996L Breakaway trim has become the
standard lever trim offering on the
98L/99L Series devices. The Breakaway
design is especially effective in areas
where vandalism to door hardware is a
problem. The design intent is to discourage
costly repairs from becoming necessary.
The Breakaway feature is not available on
the NL (night-latch) or DT (dummy trim)
versions.
6 • Von Duprin 98/99 Series
374T/376T Series thumbturn control
Standard operation, key locks and
unlocks thumbturn. Optional operation,
key unlocks thumbturn, re-locks when
key is removed. This operation is
created by changing the cylinder plate
included with control. Use 1 1/4" mortise
cylinder with a straight cam. Schlage
cam reference B502-191. Use with a pull
trim (990DT pictured).
Lever styles
Decorative levers
M51
Knurling available
M52
Knurling available
M53
M54
M55
M56
M57 ••
M61
(Handed)
M62 ••
(Handed)
M63
(Handed)
M81
Knurling available
M82
M83
M84
M85
(Handed)
•• Available in Stainless Steel substrate ONLY.
Standard Levers
01
02
Knurling available
03*
Knurling available
05
06*
Default lever
Knurling available
07
12
(Handed)
16
(Omega)
17*
Knurling available
18
ACC
(Accent)
(Handed)
AST
(Asti)
(Handed)
MER
(Merano)
(Handed)
STA
(St. Annes)
(Handed)
LAT*
Latitude
LON*
Longitude
*Available in Stainless Steel - specify SS when ordering
Von Duprin 98/99 Series • 7
98/99 Rim exit device
The 299 Strike ships
standard, optional strikes
available
98 and 99 Rim exit devices for all types of single and double doors with mullion, UL listed for panic
exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 98 device has a smooth mechanism case
and the 99 device has a grooved case. The rim device is non-handed except when the following
device options are used: SD (special dogging), -2 (double cylinder) or SS (signal switch). See
Opposite page for available outside trim and device functions. Covers stock hollow metal doors with
86 or 161 cutouts on single doors (may cover cutouts on pairs – consult template).
Hex key dogging comes standard
on 98/99 Rim exit devices
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
98/99 Rim exit device
Specifications
Device functions
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
Device lengths
3'
4'
Device centerline
from finished floor
39 13/16" (1011 mm)
39 11/16" (1008 mm) with mullion
Center case
dimensions
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
Mechanism case
dimensions
2 1/4" x 2 1/4" (57mm x 57mm)
Projection
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Latch bolt
Deadlocking, 3/4" (19mm) throw
Fasteners & sex
bolts (SNB)
Includes screw pack for 1 3/4" (44mm) and 2 1/4" (57mm) thick
metal or wood doors. Optional 425 SNB available,
see page 9 for quantities.
Electric options
LX
RX
RX2
E
EL
QEL
SS
CX
ALK
WP-RX
CON
Latchbolt monitor switch Pushpad monitor switch
Double pushpad monitor switch
Electric locking & unlocking trim Electric latch retraction
Quiet electric latch retraction
Signal switch
Chexit delayed exit
Alarm exit kit
Waterproof request to exit
Allegion Connect
-2
AX
GBK PN
XP
SNB
SEC
Double cylinder
Accessible device
Glass bead kit
Pneumatic latch retraction
Extra protection
Sex bolts
Security screws
Mechanical
options
2'4' to 3' (711mm to 914 mm) Door size
2'10" to 4' (864 mm to 1219 mm) Door size
Dogging feature
Hex key dogging standard
Dogging options
CD
SD
LD
DI
CI
Strikes
299 – Dull black
8 • Von Duprin 98/99 Series
Cylinder dogging
Special center case dogging
Less dogging
Dogging indicator
Cylinder dogging indicator
XP
CD
Extra protection
• 90˚ latch-tostrike contact
• Force resistance
of 2,000+ lbs.
Cylinder dogging
• Replaces hex key
dogging
• Requires
standard 1 1/4"
mortise cylinder
QEL
RX
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
CX
AX
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Accessible device
• UL certified to
meet new 5 lb.
maximum
operating force
requirement
• Exceeds ANSI/
BHMA
requirements
EL
ALK
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
PN
CON
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
Standard trim
EO
DT
NL
NL-OP
No outside trim
Exit only
Dummy trim
Pull when dogged
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
98EO
99EO
98DT
99DT
98NL
99NL
98NL-OP
99NL-OP
—
990DT
990NL-R/V
110NL-MD
110NL-WD
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
(76x360x2mm)
—
Pull center to center —
5 /2" (140mm)
5 /2" (140mm)
—
Projection
2" (51mm)
2" (51mm)
—
Product description
Trim description
Escutcheon plate
size
—
1
1
ANSI function
01
02
03
03
Cylinder type
—
—
Rim
Rim
—
—
—
—
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
6
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
98L
99L
98L-NL
99L-NL
98L-BE
99L-BE
98L-DT
99L-DT
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Optional #425 SNB
quantity for device
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
98/99 Rim exit device
Handing
Optional trim
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 9
98-F/99-F Rim exit device
The 299F Strike ships standard,
optional strikes available
98-F and 99-F Rim fire exit devices for all types of single doors up to 4' x 10' (1219mm x 3048mm)
or 8' x 10' (2438mm x 3048mm) double doors with 9954 or 9854 mullion, UL listed for fire exit
hardware. See page 72 for detailed information on UL listed fire exit hardware label and door opening
size information. Devices are ANSI A156.3 – 2001 Grade 1. The 98-F device has a smooth mechanism
case and the 99-F device has a grooved case. The rim device is non-handed except when the
following device options are used: -2 (double cylinder) or SS (signal switch). See opposite page for
available outside trim and device functions.
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
98-F/99-F Rim exit device
Specifications
Device functions
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
Device lengths
3'
4'
Device centerline
from finished floor
39 13/16" (1011 mm)
39 11/16" (1008 mm) with mullion
Center case
dimensions
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
Mechanism case
dimensions
2 /4" x 2 /4" (57mm x 57mm)
Projection
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Latch bolt
Deadlocking, 3/4" (19mm) throw
Fasteners & sex
bolts (SNB)
Includes screw pack for 1 3/4" (44mm) and 2 1/4" (57mm) thick
metal or wood doors. Optional 425 SNB available for metal
doors. 425 & 825 SNB required on wood doors without SLM
blocking. See page 11 for quantities.
Electric options
LX
RX
RX2
E
EL
QEL
SS
CX
ALK
WP-RX
CON
Latchbolt monitor switch Pushpad monitor switch
Double pushpad monitor switch
Electric locking & unlocking trim Electric latch retraction
Quiet electric latch retraction
Signal switch
Chexit delayed exit
Alarm exit kit
Waterproof request to exit
Allegion Connect
-2
AX
GBK PN
XP
SNB
SEC
SLM
Double cylinder
Accessible device
Glass bead kit
Pneumatic latch retraction
Extra protection
Sex bolts
Security screws
Special Laminate Material Blocking
Mechanical
options
1
2'4' to 3' (711mm to 914 mm) Door size
2'10" to 4' (864 mm to 1219 mm) Door size
1
Dogging option
No mechanical dogging. EL and QEL option available
Strikes
299F – Dull black, 499F with mullions
10 • Von Duprin 98/99 Series
499F Strike with
9854/9954 mullion
XP
RX
Extra protection
• 90˚ latch-tostrike contact
• Force resistance
of 2,000+ lbs.
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
EL
ALK
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
QEL
CX
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
AX
SG
Accessible device
• UL certified to
meet new 5 lb.
maximum
operating force
requirement
• Exceeds ANSI/
BHMA
requirements
Safety glow
• Shows exit door
location in
darkness or
smoke
• Developed to
meet MEA
standards
PN
CON
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
Standard trim
EO
DT
NL
NL-OP
No outside trim
Exit only
Dummy trim
Pull when dogged
(not recommended for fire device)
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
98EO-F
99EO-F
98DT-F
99DT-F
98NL-F
99NL-F
98NL-OP-F
99NL-OP-F
—
990DT
990NL-R/V
110NL-MD
110NL-WD
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
(76x360x2mm)
—
Pull center to center —
5 /2" (140mm)
5 /2" (140mm)
—
Projection
2" (51mm)
2" (51mm)
—
Product description
Trim description
Escutcheon plate
size
—
1
1
ANSI function
01
02
03
03
Cylinder type
—
—
Rim
Rim
—
—
—
—
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
#425 SNB optional
- HMD req. WD w/o
SLM pkg.
2
2
2
2
#825 SNB req. WD
w/o SLM pkg.
2 (if using trim)
2
2
2
#425 SNB req.
w/ 499F
2
2
2
2
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
(not recommended for fire device)
98L-F
99L-F
98L-NL-F
99L-NL-F
98L-BE-F
99L-BE-F
98L-DT-F
99L-DT-F
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Product description
98-F/99-F Rim exit device
Handing
Optional trim
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
#425 SNB optional
- HMD req. WD w/o
SLM pkg.
2
2
2
2
#825 SNB req. WD
w/o SLM pkg.
2 (if using trim)
2
2
2
#425 SNB req.
w/ 499F
2
2
2
2
* Electrified lever operation available
Von Duprin 98/99 Series • 11
9875/9975 Mortise lock device
7500 Mortise
Lock
9875/9975 Mortise lock device for all types of single or double doors, UL listed for Panic exit
hardware. Devices are ANSI A156.3 – 2001 Grade 1. Fits stock hollow metal doors with 86 cutout and
door stiles as narrow as 4 3/4" (121mm). The 9875 device has a smooth mechanism case and the
9975 device has a grooved case. The mortise lock device is non-handed except when the following
device options are used: -2 (double cylinder) or SS (signal switch). See opposite page for available
outside trim and device functions.
575 Strike
Hex key dogging comes standard on
9875/9975 Mortise Lock Devices
9875/9975 Mortise lock device
The 7500 Mortise lock is equipped with a 3/4" (19mm) anti-friction latch bolt which is field reversible
without removing the lock from the door. It has a non-handed auxiliary bolt for deadlocking and a
faceplate with an adjustable bevel.
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
Device lengths
3'
4'
Device centerline
from finished floor
39 13/16" (1011 mm)
39 11/16" (1008 mm) with mullion
Center case
dimensions
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
Mechanism case
dimensions
2 1/4" x 2 1/4" (57mm x 57mm)
Projection
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Fasteners & sex
bolts (SNB)
Includes screw pack for 1 3/4" (44mm) and 2 1/4" (57mm) thick
metal or wood doors. Optional 425 SNB available, see page 13
for quantities.
Electric options
RX
RX2
E
EL
QEL
SS
CX
ALK
WP-RX
CON
Pushpad monitor switch
Double pushpad monitor switch
Electric locking & unlocking trim Electric latch retraction
Quiet electric latch retraction
Signal switch
Chexit delayed exit
Alarm exit kit
Waterproof request to exit
Allegion Connect
Mechanical
options
-2
GBK PN
SNB
SEC
Double cylinder
Glass bead kit
Pneumatic latch retraction
Sex bolts
Security screws
Dogging feature
Hex key dogging standard
Dogging option
CD
SD
LD
DI
CI
Strikes
575 – Dull Black
12 • Von Duprin 98/99 Series
2'4' to 3' (711mm to 914 mm) Door size
2'10" to 4' (864 mm to 1219 mm) Door size
Cylinder dogging
Special center case dogging
Less dogging
Dogging indicator
Cylinder dogging indicator
QEL
CD
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Cylinder dogging
• Replaces hex key
dogging
• Requires
standard 1 1/4"
mortise cylinder
CX
RX
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
EL
ALK
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
E (E7500)
CON
Electric mortise
lock device
• Remains latched
while unlocked
• Remote electrical
control
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
PN
SS 7500
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Signal switch
• Signals
unauthorized use
of an opening
• Switch makes
latch bolt
tamper-resistant
Standard trim
EO
DT
NL
HL
No outside trim
Exit only
Dummy trim
Pull when dogged
(not recommended for fire device)
Night latch
Key retracts latchbolt
Hospital latch
Key locks & unlocks
Product description
9875EO
9975EO
9875DT
9975DT
9975NL
9875NL
9875HL
Trim description
—
990DT
990NL-M
HL6M
—
3" x 14 3/16" x 3/32"
(76x360x2mm)
3" x 14 3/16" x 3/32"
(76x360x2mm)
2 9/16" x 5 1/2" x 2 5/8"
(65x140x67mm)
Pull center to center —
5 1/2" (140mm)
5 1/2" (140mm)
–
Projection
2" (51mm)
2" (51mm)
2 5/8" (67mm)
Escutcheon plate
size
—
9975HL
01
02
03
—
—
—
1 1/4" Mortise
1 1/4" Mortise
x990EO
x996EO
x996K-DT
x996L-DT)
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
2
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
9875L
9975L
9875L-NL
9975L-NL
9875L-BE
9975L-BE
9875L-DT
9975L-DT
Trim description
996L-M*
996L-NL-M
996L-BE-M*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Handing
Optional trim
Optional #425 SNB
quantity for device
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
1 1/4" Mortise
1 1/4" Mortise
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
9875/9975 Mortise lock device
ANSI function
Cylinder type
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 13
9875-F/9975-F Mortise lock fire exit device
9875-F/9975-F Mortise lock fire exit device
9875-F/9975-F Fire exit mortise lock devices for all types of single doors up to 4' x 10' (1219mm x
3048mm) or 8' x 10' (2438mm x 3048mm) double doors installations, UL listed for fire exit
hardware; See page 72 for detailed information on UL listed fire exit hardware label and door opening
size information. Devices are ANSI A156.3 – 2001 Grade 1. Fits door stiles as narrow as 4 3/4" (121mm).
The 9875-F device has a smooth mechanism case and the 9975-F device has a grooved case. The
mortise lock device is non-handed except when the following device options are used: -2 (double
cylinder) or SS (signal switch) devices. See opposite page for available outside trim and functions.
7500 Mortise
Lock
575 Strike
The 7500 Mortise lock is equipped with 3/4" (19mm) anti-friction latch bolt which is field reversible
without removing the lock from the door. It has a non-handed auxiliary bolt for deadlocking and a
faceplate with an adjustable bevel.
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw.
Device lengths
3'
4'
Device centerline
from finished floor
39 13/16" (1011 mm)
39 11/16" (1008 mm) with mullion
Center case
dimensions
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
Mechanism case
dimensions
2 1/4" x 2 1/4" (57mm x 57mm)
Projection
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Fasteners & sex
bolts (SNB)
Includes screw pack for 1 3/4" (44mm) and 2 1/4" (57mm) thick
metal or wood doors. Optional 425 SNB available for metal
doors. 425 & 825 SNB required on wood doors without SLM
blocking. See page 11 for quantities.
2'4' to 3' (711mm to 914 mm) Door size
2'10" to 4' (864 mm to 1219 mm) Door size
RX
RX2
E
EL
QEL
SS
CX
ALK
WP-RX
CON
Pushpad monitor switch
Double pushpad monitor switch
Electric locking & unlocking trim Electric latch retraction
Quiet electric latch retraction
Signal switch
Chexit delayed exit
Alarm exit kit
Waterproof request to exit
Allegion Connect
Mechanical
options
-2
GBK PN
SNB
SEC
SLM
Double cylinder
Glass bead kit
Pneumatic latch retraction
Sex bolts
Security screws
Special Laminate Material Blocking
Dogging option
No Mechanical Dogging. EL and QEL option available
Strikes
575 – Dull Black
Electric options
14 • Von Duprin 98/99 Series
QEL
RX
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
CX
ALK
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
EL
SG
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Safety glow
• Shows exit door
location in
darkness or
smoke
• Developed to
meet MEA
standards
E (E7500)
SS 7500
Electric mortise
lock device
• Remains latched
while unlocked
• Remote electrical
control
Signal switch
• Signals
unauthorized use
of an opening
• Switch makes
latch bolt
tamper-resistant
PN
CON
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
Standard trim
DT
NL
HL
No outside trim
Exit only
Dummy trim
Pull when dogged
(not recommended for fire device)
Night latch
Key retracts latchbolt
Hospital latch
Key locks & unlocks
Product description
9875EO-F
9975EO-F
—
—
9875NL-F
9975NL-F
9875HL-F
9975HL-F
Trim description
—
990DT
990NL-M
HL6M
—
3" x 14 3/16" x 3/32"
(76x360x2mm)
3" x 14 3/16" x 3/32"
(76x360x2mm)
2 9/16" x 5 1/2" x 2 5/8"
(65x140x67mm)
Pull center to center —
5 1/2" (140mm)
5 1/2" (140mm)
–
Projection
2" (51mm)
2" (51mm)
2 5/8" (67mm)
Escutcheon plate
size
—
ANSI function
01
02
03
—
Cylinder type
—
—
1 1/4" Mortise
1 1/4" Mortise
x990EO
x996EO
x996K-DT
x996L-DT)
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
2
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
(not recommended for fire device)
9875L-F
9975L-F
9875L-NL-F
9975L-NL-F
9875L-BE-F
9975L-BE-F
—
—
Trim description
996L-M*
996L-NL-M
996L-BE-M*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Handing
Optional trim
Optional #425 SNB
quantity for device
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
1 1/4" Mortise
1 1/4" Mortise
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
9875-F/9975-F Mortise lock fire exit device
EO
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 15
9827/9927 Surface mounted vertical rod device
Top latch
299 Top strike
9827/9927 Surface mounted vertical rod device
9827/9927 Surface mounted vertical rod device for all types of single or double doors, UL listed for
panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. Covers stock hollow metal doors with
86 or 161 cutouts. The 9827 device has a smooth mechanism case and the 9927 device has a grooved
case. The surface vertical rod device is non-handed except when the following device options are
used: SD (special dogging), or SS (signal switch). See opposite page for available outside trim and
functions.Vertical rod and latch guards are available to protect the bottom rod of the exit device from
damage by impacts of carts or gurneys passing through doors.
248L4 Bottom
Strike for use with
flat threshold
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Center case
dimensions
Mechanism case
dimensions
Projection
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm)
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
2 1/4" x 2 1/4" (57mm x 57mm)
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Latch bolt
Deadlocking anti-friction top & bottom bolt, 5/8" (16mm) throw
Door undercut
1
Top & bottom
Latch case
Vertical rods
4 /2" x 2 /8" x 1 /2" (114mm x 54mm x 38mm)
Fasteners & sex
bolts (SNB)
Electric options
Mechanical
options
Dogging feature
Dogging option
Strikes
16 • Von Duprin 98/99 Series
/4" (7mm) recommended
1
1
1
/2" square tubing, standard rods accommodate 7' (2134mm)
doors. Top rod length: 34 15/16" (887mm); Bottom rod length:
31 1/2" (794mm) Extension rods available in 1' (205mm) or 3'
(914mm) for doors over 7'. One piece top rod is available for 8'
(2438mm) and 10' (3048mm) doors.
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
metal or wood doors, and 325 SNB for top and bottom latch.
Optional 425 SNB available.
LX
Latchbolt monitor switch
RX
Pushpad monitor switch
RX2
Double pushpad monitor switch
EL
Electric latch retraction
QEL
Quiet electric latch retraction
SS
Signal switch
CX
Chexit delayed exit
ALK
Alarm exit kit
PN
Pneumatic latch retraction
LBR
Less bottom rod
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
PL
Pullman latch
WS
Tornado and hurricane tested
SNB
Sex bolts
SEC
Security screws
Hex key dogging standard
CD
Cylinder dogging
SD
Special center case dogging
LD
Less dogging
DI
Dogging indicator
CI
Cylinder dogging indicator
Top - 299 – Dull black, Bottom – 248L4 & 304L - Unfinished
1
304L
Bottom strike
Bottom latch
Hex key dogging comes
standard on 9827/9927
WS
RX
Windstorm
• Severe weather
certified/tested
• FEMA and ICC
compliant
• Tornado &
hurricane tested
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
QEL
CON
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
EL
ALK
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
E (E996L)
CX
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
PN
SS
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Signal switch
• Signals
unauthorized use
of an opening
• Switch makes
latch bolt
tamper-resistant
Standard trim
EO
DT
NL
NL-OP
TL
TL-BE
Dummy trim
Pull when dogged
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Thumbturn
Key locks & unlocks
(use with DT trim)
9827EO
9927EO
9827DT
9927DT
9827NL
9927NL
9827NL-OP
9927NL-OP
9827TL
9927TL
9827TL-BE
9927TL-BE
—
990DT
990NL-R/V
110NL-MD
110NL-WD
374T X 990DT
374T-BE X
990DT
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
(76x360x2mm)
—
1 11/16" x 7 1/2" x 7/8"
(43x191x22mm)
1 11/16" x 7 1/2" x 7/8"
(43x191x22mm)
Pull center to center —
5 1/2" (140mm)
5 1/2" (140mm)
—
—
—
Projection
—
2" (51mm)
2" (51mm)
—
3 1/4" (83mm)
3 1/4" (83mm)
ANSI function
01
02
03
03
11 or 12
16
Cylinder type
—
—
Rim
Rim
1 1/4" Mortise
—
Handing
—
—
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
6
2
2
Product description
Trim description
Escutcheon plate
size
Optional #425 SNB
quantity for device
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
9827L
9927L
9827L-NL
9927L-NL
9827L-BE
9927L-BE
9827L-DT
9927L-DT
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
9827/9927 Surface mounted vertical rod device
No outside trim
Exit only
Thumbturn
Blank escutcheon
always operable
(no cylinder)
(use with DT trim)
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 17
9827-F/9927-F Surface Mounted Vertical Rod Fire Device
Top latch
9827/9927 Surface mounted vertical rod device
299 Top strike
9827-F/9927-F Fire exit surface mounted vertical rod device pairs of doors up to 8' x 10'
(2438mm x 3048mm) , UL listed for fire exit hardware. See page 72 for detailed information on
UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 –
2001 Grade 1. The 9827-F device has a smooth mechanism case and the 9927-F device has a
grooved case. The surface vertical rod device is non-handed except when the following device
options are used: SS (signal switch). See opposite page for available outside trim and device
functions. Vertical rod and latch guards are available to protect the bottom rod of the exit device
from damage by impacts of carts or gurneys passing through doors. Rod and latch guards can be
used on hollow metal or tin clad composite fire doors.
Finishes – US3, US4, US10, US26, US26D, US28 & 313. US15 and US32D available with 98
Series only.
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Center case
dimensions
Mechanism case
dimensions
Projection
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm)
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
2 1/4" x 2 1/4" (57mm x 57mm)
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Latch bolt
Deadlocking anti-friction top & bottom bolt, 5/8" (16mm) throw
Door undercut
1
Top & bottom
Latch case
Vertical rods
4 1/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm)
Fasteners & sex
bolts (SNB)
Electric options
Mechanical
options
Dogging option
Strikes
18 • Von Duprin 98/99 Series
/4" (7mm) recommended
/2" square tubing, standard rods accommodate 7' (2134mm)
doors. Top rod length: 34 15/16" (887mm); Bottom rod length:
31 1/2" (794mm) Extension rods available in 1' (205mm) or 3'
(914mm) for doors over 7'. One piece top rod is available for 8'
(2438mm) and 10' (3048mm) doors.
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
metal or wood doors, and 325 SNB for top and bottom latch.
Optional 425 SNB available.
LX
Latchbolt monitor switch
RX
Pushpad monitor switch
RX2
Double pushpad monitor switch
E
Electric unlocking and locking trim
EL
Electric latch retraction
QEL
Quiet electric latch retraction
SS
Signal switch
CX
Chexit delayed exit
ALK
Alarm exit kit
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
PN
Pneumatic latch retraction
LBR
Less bottom rod
PL
Pullman latch
WS
Tornado and hurricane tested
SNB
Sex bolts
SEC
Security screws
SLM
Special laminate material blocking
No mechanical dogging. EL and QEL option available
Top – 299F (499F LBR) Dull black, Bottom – 304L - Unfinished
1
499F
Top strike - LBR
304L
Bottom strike
Bottom latch
WS
RX
Windstorm
• Severe weather
certified/tested
• FEMA and ICC
compliant
• Tornado &
hurricane tested
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
QEL
ALK
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
EL
CX
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
E (E996L)
LBR
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Less bottom rod
• Available with UL
Fire Label
• For pairs of
vertical rod
devices
PN
CON
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
Standard trim
TL-BE
Night latch
Key retracts latchbolt
optional pull required
Thumbturn
Key locks & unlocks
(use with DT trim)
Thumbturn
Blank escutcheon
always operable
(no cylinder)
(use with DT trim)
9827NL-F
9927NL-F
9827NL-OP-F
9927NL-OP-F
9827TL-F
9927TL-F
9827TL-BE-F
9927TL-BE-F
990DT
990NL-R/V
110NL-MD
110NL-WD
374T X 990DT
374T-BE X
990DT
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
(76x360x2mm)
—
1 11/16" x 7 1/2" x 7/8"
(43x191x22mm)
1 11/16" x 7 1/2" x 7/8"
(43x191x22mm)
Pull center to center —
5 1/2" (140mm)
5 1/2" (140mm)
—
—
—
Projection
—
2" (51mm)
2" (51mm)
—
2" (51mm)
2" (51mm)
ANSI function
01
02
03
03
11 or 12
16
Cylinder type
—
—
Rim
Rim
1 1/4" Mortise
—
Handing
—
—
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
6
2
2
Trim description
Escutcheon plate
size
Optional #425 SNB
quantity for device
DT
NL
No outside trim
Exit only
Dummy trim
Pull when dogged
(not recommended for
fire device)
Night latch
Key retracts latchbolt
9827EO-F
9927EO-F
—
—
—
—
NL-OP
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
(not recommended for fire device)
9827L-F
9927L-F
9827L-NL-F
9927L-NL-F
9827L-BE-F
9927L-BE-F
—
—
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
9827/9927 Surface mounted vertical rod device
TL
Product description
EO
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 19
9857/9957 Three-point latching device
Top latch
299 Top & middle
strike
9857/9957 Three-point latching device for all types of single or double doors, UL listed for panic
exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. Covers stock hollow metal doors with 86 or
161 cutouts. The 9857 device has a smooth mechanism case and the 9957 device has a grooved case.
The three-point latching device is non-handed except when the following device options are used:
SD (special dogging), or SS (signal switch). See opposite page for available outside trim and
functions. Vertical rod and latch guards are available to protect the bottom rod of the exit device
from damage by impacts of carts or gurneys passing through doors.
248L4 Bottom
Strike for use with
flat threshold
9857/9957 Three-point latching device
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Center case
dimensions
Mechanism case
dimensions
Projection
Latch bolt
Door undercut
Top & bottom
Latch case
Vertical rods
Fasteners & sex
bolts (SNB)
Electric options
Mechanical
options
Dogging feature
Dogging option
Strikes
20 • Von Duprin 98/99 Series
304L
Bottom strike
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
3913/16" (1011 mm)
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
2 1/4" x 2 1/4" (57mm x 57mm)
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Deadlocking anti-friction top & bottom bolt, 5/8" (16mm) throw
Deadlocking rim bolt, 3/4" (19mm) throw
1
/4" (7mm) recommended
4 1/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm)
/2" square tubing, standard rods accommodate 7' (2134mm)
doors. Top rod length: 34 15/16" (887mm); Bottom rod length:
31 1/2" (794mm) Extension rods available in 1' (205mm) or 3'
(914mm) for doors over 7'. One piece top rod is available for 8'
(2438mm) and 10' (3048mm) doors.
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
metal or wood doors, and 325 SNB for top and bottom latch.
Optional 425 SNB available.
LX
Latchbolt monitor switch
RX
Pushpad monitor switch
RX2
Double pushpad monitor switch
E
Electric unlocking and locking trim
EL
Electric latch retraction
QEL
Quiet electric latch retraction
SS
Signal switch
CX
Chexit delayed exit
ALK
Alarm exit kit
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
PN
Pneumatic latch retraction
PL
Pullman latch
WS
Tornado and hurricane tested
SNB
Sex bolts
SEC
Security screws
Hex key dogging standard
CD
Cylinder dogging
SD
Special center case dogging
LD
Less dogging
DI
Dogging indicator
CI
Cylinder dogging indicator
Top & middle – 299 - Dull black
Bottom – 248L4 & 304L - Unfinished
1
Bottom latch
Hex key dogging comes
standard on 9857/9957
Three-point latching
devices
WS
CON
Windstorm
• Severe weather
certified/tested
• FEMA and ICC
compliant
• Tornado &
hurricane tested
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
PN
ALK
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
EL
RX
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
E (E996L)
LX
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Latchbolt monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor latch bolt
QEL
SS
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Signal switch
• Signals
unauthorized use
of an opening
• Switch makes
latch bolt
tamper-resistant
Standard trim
EO
DT
NL
NL-OP
TL
TL-BE
No outside trim
Exit only
Dummy trim
Pull when dogged
(not recommended for
fire device)
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Thumbturn
Key locks & unlocks
(use with DT trim)
Thumbturn
Blank escutcheon
always operable
(no cylinder)
(use with DT trim)
9857EO
9957EO
9857DT
9957DT
9857NL
9957NL
9857NL-OP
9957NL-OP
9857TL
9957TL
9857TL-BE
9957TL-BE
—
990DT
990NL-R/V
110NL-MD
110NL-WD
374T X 990DT
374T-BE X 990DT
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
—
(76x360x2mm)
Pull center to center —
5 1/2" (140mm)
5 1/2" (140mm)
—
—
—
Projection
2" (51mm)
2" (51mm)
—
2" (51mm)
2" (51mm)
Product description
Trim description
Escutcheon plate
size
ANSI function
01
02
03
03
11 or 12
16
Cylinder type
—
—
Rim
Rim
1 1/4" Mortise
—
Handing
—
—
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
6
2
2
Optional #425 SNB
quantity for device
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
9857L
9957LF
9857L-NL
9957L-NL
9857L-BE
9957L-BE
—
—
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
9857/9957 Three-point latching device
—
2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
(70x273x21mm)
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 21
9857-F/9957-F Three-point latching fire exit device
Top latch
9857-F/9957-F Three-point latching fire exit device
299 Top & middle
strike
9857-F/9957-F Fire exit three-point latching device for all types of single doors up to 4' x 8'
(1219mm x 2438mm) or up to 8' x 8'(2438mm x 2438mm) double doors with 9954 or 9854
mullion, UL listed for fire exit hardware. See page 72 for detailed information on UL listed fire exit
hardware label and door opening size information. Devices are ANSI A156.3 – 2001 Grade 1. The
9857-F device has a smooth mechanism case and the 9957-F device has a grooved case. The
three-point latch device is non-handed except when the following device option is used:
SS (signal switch). See opposite page for available outside trim and device functions. Vertical
rod and latch guards are available to protect the bottom rod of the exit device from damage by
impacts of carts or gurneys passing through doors.
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313,
315 & 643E. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Center case
dimensions
Mechanism case
dimensions
Projection
Latch bolt
Door undercut
Top & bottom
Latch case
Vertical rods
Fasteners & sex
bolts (SNB)
Electric options
Mechanical
options
Dogging option
Strikes
22 • Von Duprin 98/99 Series
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
3913/16" (1011 mm)
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
2 1/4" x 2 1/4" (57mm x 57mm)
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Deadlocking anti-friction top & bottom bolt, 5/8" (16mm) throw
Deadlocking rim bolt, 3/4" (19mm) throw
1
/4" (7mm) recommended
4 1/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm)
/2" square tubing, standard rods accommodate 7' (2134mm)
doors. Top rod length: 34 15/16" (887mm); Bottom rod length:
31 1/2" (794mm) Extension rods available in 1' (205mm) or 3'
(914mm) for doors over 7'. One piece top rod is available for 8'
(2438mm) and 10' (3048mm) doors.
Includes screw pack for 13/4" (44mm) and 2 1/4" (57mm) thick
metal or wood doors, and 325 SNB for top and bottom latch.
Optional 425 SNB available for metal doors. 425 SNB required
on wood doors without SLM blocking.
LX
Latchbolt monitor switch
RX
Pushpad monitor switch
RX2
Double pushpad monitor switch
E
Electric unlocking and locking trim
EL
Electric latch retraction
QEL
Quiet electric latch retraction
SS
Signal switch
CX
Chexit delayed exit
ALK
Alarm exit kit
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
PN
Pneumatic latch retraction
SNB
Sex bolts
SEC
Security screws
SLM
Special laminate material blocking
No mechanical dogging. EL and QEL option available
Top & middle – 299 - Dull black
Bottom – 304L - Unfinished
304L
Bottom strike
499F Rim Strike
for Mullion
Applications
Bottom latch
PN
RG
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Rod guard
• Protection from
carts/gurneys
• Eases wheelchair
access
EL
QEL
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
E (E996L)
LX
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Latchbolt monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor latch bolt
RX
CX
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
ALK
CON
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
1
Standard trim
EO
DT
NL
NL-OP
TL
TL-BE
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Thumbturn
Key locks & unlocks
(use with DT trim)
Thumbturn
Blank escutcheon
always operable
(no cylinder)
(use with DT trim)
9857EO-F
9957EO-F
9857DT-F
9957DT-F
9857NL-F
9957NL-F
9857NL-OP-F
9957NL-OP-F
9857TL-F
9957TL-F
9857TL-BE-F
9957TL-BE-F
—
990DT
990NL-R/V
110NL-MD
110NL-WD
374T X 990DT
374T-BE X 990DT
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
—
(76x360x2mm)
Pull center to center —
5 1/2" (140mm)
5 1/2" (140mm)
—
—
—
Projection
2" (51mm)
2" (51mm)
—
2" (51mm)
2" (51mm)
Product description
Trim description
Escutcheon plate
size
—
2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
(70x273x21mm)
ANSI function
01
02
03
03
11 or 12
16
Cylinder type
—
—
Rim
Rim
1 1/4" Mortise
—
Handing
—
—
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
#425 SNB optional
- HMD req. WD
w/o SLM pkg.
6
2
2
6
2
2
#425 SNB req.
w/ 499F
2
2
2
2
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
9857L-F
9957L-F
9857L-NL-F
9957L-NL-F
9857L-BE-F
9957L-BE-F
—
—
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
#425 SNB optional
- HMD req. WD
w/o SLM pkg.
2
2
2
2
#425 SNB req.
w/ 499F
2
2
2
2
9857-F/9957-F Three-point latching fire exit device
No outside trim
Exit only
Dummy trim
Pull when dogged
(not recommended for
fire device)
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 23
9847/9947 Concealed vertical rod device
Top Latch
338
Top Strike
9847/9947 Concealed vertical rod device for use on single or double metal doors, UL listed for
panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9847 device has a smooth
mechanism case and the 9947 device has a grooved case. The concealed vertical rod device is
non-handed except when the following device options are used: SD (special dogging), or SS (signal
switch). See opposite page for available outside trim and device functions.
9847/9947 Concealed vertical rod device
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
385A
Bottom Strike
Bottom Latch
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Center case
dimensions
Mechanism case
dimensions
Projection
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm) Standard
Adjustable from 355/8" (905mm) to 495/8" (1260mm)
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
2 1/4" x 2 1/4" (57mm x 57mm)
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Latch bolt
Deadlocking top & bottom bolt, 5/8" (16mm) throw
Door undercut
1
Top & bottom
Latch case
Vertical rods
4 1/2" x 2 1/8" x 1 1/2" (114mm x 54mm x 38mm)
Fasteners & sex
bolts (SNB)
Electric options
Mechanical
options
Dogging feature
Dogging option
Strikes
24 • Von Duprin 98/99 Series
/4" (7mm) recommended
Round 2-piece adjustable rods – Top rod adjustable from 6'8"
(2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5/8"
(905 mm) to 49 5/8" (1260 mm). Extension rod kits available for
doors over 8'4" (2533mm).
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
metal doors. Optional 425 SNB available.
LX
Latchbolt monitor switch
RX
Pushpad monitor switch
RX2
Double pushpad monitor switch
E
Electric unlocking and locking trim
EL
Electric latch retraction
QEL
Quiet electric latch retraction
SS
Signal switch
CX
Chexit delayed exit
ALK
Alarm exit kit
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
PN
Pneumatic latch retraction
LBR
Less bottom rod
PL
Pullman latch
SNB
Sex bolts
SEC
Security screws
Hex key dogging standard
CD
Cylinder dogging
SD
Special center case dogging
LD
Less dogging
DI
Dogging indicator
CI
Cylinder dogging indicator
Top – 338 - Unfinished, Bottom – 385A - Unfinished
Hex key dogging comes
standard on 9847/9947
Concealed vertical rod
devices
QEL
RX
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
CX
CON
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
EL
ALK
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
E (E996L)
LX
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Latchbolt monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor latch bolt
PN
DI
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Dogging indicator
• Monitor dogging
status without a
control panel
• Red indicator
light shows
visibility to
dogging from
over 75 feet
Standard trim
EO
DT
NL
NL-OP
TL
TL-BE
No outside trim
Exit only
Dummy trim
Pull when dogged
(not recommended for
fire device)
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Thumbturn
Key locks & unlocks
(use with DT trim)
Thumbturn
Blank escutcheon
always operable
(no cylinder)
(use with DT trim)
Product description
9847EO
9947EO
9847DT
9947DT
9847NL
9947NL
9847NL-OP
9947NL-OP
9847TL
9947TL
9847TL-BE
9947TL-BE
Trim description
—
990DT
990NL-R/V
110NL-MD
374T X 990DT
374T-BE X 990DT
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
—
(76x360x2mm)
2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
(70x273x21mm)
5 1/2" (140mm)
5 1/2" (140mm)
—
—
Escutcheon plate
size
Pull center to center —
—
—
2" (51mm)
2" (51mm)
—
2" (51mm)
2" (51mm)
ANSI function
01
02
03
03
11 or 12
16
Cylinder type
—
—
Rim
Rim
1 1/4" Mortise
—
Handing
—
—
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
6
2
2
Optional #425 SNB
quantity for device
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
9847L
9947LF
9847L-NL
9947L-NL
9847L-BE
9947L-BE
9847L-DT
9947L-DT
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
9847/9947 Concealed vertical rod device
Projection
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 25
9847-F/9947-F Concealed vertical rod fire exit device
Top Latch
9847-F/9947-F Concealed vertical rod fire exit device
338
Top Strike
9847-F/9947-F Fire exit concealed vertical rod device for use on pairs of doors up to 8' x 10'
(2438mm x 3048mm) , UL listed for fire exit hardware. See page 72 for detailed information on
UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3
– 2001 Grade 1. The 9847-F device has a smooth mechanism case and the 9947-F device has a
grooved case. The concealed vertical rod device is non-handed except when the following device
option is used: SS (signal switch) devices. See opposite page for available outside trim and
functions.
385A
Bottom Strike
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313,
315 & 643E. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm) Standard
Adjustable from 355/8" (905mm) to 495/8" (1260mm)
Center case
dimensions
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
Mechanism case
dimensions
2 1/4" x 2 1/4" (57mm x 57mm)
Projection
Pushbar neutral – 3 /16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
13
Latch bolt
Deadlocking top & bottom bolt, 5/8" (16mm) throw
/4" (7mm) recommended
Door undercut
1
Top & bottom
Latch case
3 3/4" x 1 1/2" x 1" (95mm x 38mm x 25mm)
Vertical rods
Round 2-piece adjustable rods – Top rod adjustable from 6'8"
(2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5/8"
(905 mm) to 49 5/8" (1260 mm). Extension rod kits available for
doors over 8'4" (2533mm).
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
metal doors. Optional 425 SNB available.
Fasteners & sex
bolts (SNB)
Electric options
Mechanical
options
Dogging option
Strikes
26 • Von Duprin 98/99 Series
LX
Latchbolt monitor switch
RX
Pushpad monitor switch
RX2
Double pushpad monitor switch
E
Electric unlocking and locking trim
EL
Electric latch retraction
QEL
Quiet electric latch retraction
SS
Signal switch
CX
Chexit delayed exit
ALK
Alarm exit kit
WP-RX Waterproof request to exit
CON
Allegion Connect
LBR
Less bottom rod
PN
Pneumatic latch retraction
GBK Glass bead kit
SNB
Sex bolts
SEC
Security screws
SLM
Special laminate material blocking
No mechanical dogging. EL and QEL option available
Top – 338 - Unfinished, Bottom – 385A - Unfinished
Bottom Latch
PN
RG
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Rod guard
• Protection from
carts/gurneys
• Eases wheelchair
access
EL
QEL
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
E (E996L)
LX
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Latchbolt monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor latch bolt
RX
CX
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
ALK
CON
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
Standard trim
EO
DT
NL
NL-OP
TL
TL-BE
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Thumbturn
Key locks & unlocks
(use with DT trim)
Thumbturn
Blank escutcheon
always operable
(no cylinder)
(use with DT trim)
Product description
9847EO-F
9947EO-F
—
—
9847NL-F
9947NL-F
9847NL-OP-F
9947NL-OP-F
9847TL-F
9947TL-F
9847TL-BE-F
9947TL-BE-F
Trim description
—
990DT
990NL-R/V
110NL-MD
374T X 990DT
374T-BE X 990DT
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
—
(76x360x2mm)
2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
(70x273x21mm)
5 1/2" (140mm)
5 1/2" (140mm)
—
—
Escutcheon plate
size
Pull center to center —
—
Projection
—
2" (51mm)
2" (51mm)
—
2" (51mm)
2" (51mm)
ANSI function
01
02
03
03
11 or 12
16
Cylinder type
—
—
Rim
Rim
1 1/4" Mortise
—
Handing
—
—
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
6
2
2
#425 SNB optional
- HMD req. WD
w/o SLM pkg.
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
9847L-F
9947L-F
9847L-NL-F
9947L-NL-F
9847L-BE-F
9947L-BE-F
—
—
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
#425 SNB optional
- HMD req. WD
w/o SLM pkg.
2
2
2
2
9847-F/9947-F Concealed vertical rod fire exit device
No outside trim
Exit only
Dummy trim
Pull when dogged
(not recommended for
fire device)
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 27
9848/9948 Concealed vertical rod device
Top Latch
338
Top Strike
9848/9948 Concealed vertical rod device for use on single or double metal doors, UL listed for
panic exit hardware. Covers stock hollow metal doors with 86 or 161 cutouts. Devices are ANSI A156.3
– 2001 Grade 1. The 9848 device has a smooth mechanism case and the 9948 device has a grooved
case. The concealed vertical rod device is non-handed except when the following device options are
used:SD (special dogging), or SS (signal switch). See opposite page for available outside trim and
functions.
385A
Bottom Strike
9848/9948 Concealed vertical rod device
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Bottom Latch
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm) Standard
Adjustable from 355/8" (905mm) to 495/8" (1260mm)
Center case
dimensions
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
Mechanism case
dimensions
2 1/4" x 2 1/4" (57mm x 57mm)
Projection
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Latch bolt
Deadlocking top bolt, 3/4" (19mm) throw
Deadlocking bottom bolt, 1 1/2" (38mm) throw
3
/4" (19mm) maximum, more than 1/4" minimum
Door undercut
Top & bottom
Latch case
4 1/4" x 1 1/2" x 1 1/8" (107mm x 38mm x 28mm)
Vertical rods
Round 2-piece adjustable rods – Top rod adjustable from 6'8"
(2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5/8"
(905 mm) to 49 5/8" (1260 mm). Extension rod kits available for
doors over 8'4" (2533mm).
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
metal doors. Optional 425 SNB available.
Fasteners & sex
bolts (SNB)
Electric options
Mechanical
options
Dogging feature
Dogging option
Strikes
28 • Von Duprin 98/99 Series
LX
Latchbolt monitor switch
RX
Pushpad monitor switch
RX2
Double pushpad monitor switch
E
Electric unlocking and locking trim
EL
Electric latch retraction
QEL
Quiet electric latch retraction
SS
Signal switch
CX
Chexit delayed exit
ALK
Alarm exit kit
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
PN
Pneumatic latch retraction
SNB
Sex bolts
SEC
Security screws
Hex key dogging standard
CD
Cylinder dogging
SD
Special center case dogging
LD
Less dogging
DI
Dogging indicator
CI
Cylinder dogging indicator
Top – 338 - Unfinished, Bottom – 385A - Unfinished
Hex key dogging comes
standard on 9848/9948
Concealed vertical rod
devices
CX
ALK
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
EL
SS
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Signal switch
• Signals
unauthorized use
of an opening
• Switch makes
latch bolt
tamper-resistant
QEL
LX
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Latchbolt monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor latch bolt
E (E996L)
SG
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Safety glow
• Shows exit door
location in
darkness or
smoke
• Developed to
meet MEA
standards
PN
CON
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
Standard trim
EO
DT
NL
NL-OP
TL
TL-BE
No outside trim
Exit only
Dummy trim
Pull when dogged
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Thumbturn
Key locks & unlocks
(use with DT trim)
Thumbturn
Blank escutcheon
always operable
(no cylinder)
(use with DT trim)
Product description
9848EO
9948EO
9848DT
9948DT
9848NL
9948NL
9848NL-OP
9948NL-OP
9848TL
9948TL
9848TL-BE
9948TL-BE
Trim description
—
990DT
990NL-R/V
110NL-MD
374T X 990DT
374T-BE X 990DT
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
—
(76x360x2mm)
2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
(70x273x21mm)
Escutcheon plate
size
5 1/2" (140mm)
5 1/2" (140mm)
—
—
—
—
2" (51mm)
2" (51mm)
—
3 /4" (83mm)
3 1/4" (83mm)
ANSI function
01
02
03
03
11
—
Cylinder type
—
—
Rim
Rim
1 1/4" Mortise
—
Handing
—
—
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
6
2
2
Optional #425 SNB
quantity for device
1
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
9848L
9948LF
9848L-NL
9948L-NL
9848L-BE
9948L-BE
9848L-DT
9948L-DT
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
9848/9948 Concealed vertical rod device
Pull center to center —
Projection
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 29
9848-F/9948-F Concealed vertical rod fire exit device
Top Latch
9848-F/9948-F Concealed vertical rod fire exit device
338
Top Strike
9848-F/9948-F Concealed vertical rod device for use on pairs of doors up to 8' x 10'
(2438mm x 3048mm), UL listed for fire exit hardware. See page 72 for detailed information on
UL listed fire exit hardware label and door opening size information. Devices are ANSI A156.3 –
2001 Grade 1. The 9848-F device has a smooth mechanism case and the 9948-F device has a
grooved case. The concealed vertical rod device is non-handed except when the following device
option is used: SS (signal switch). See opposite page for available outside trim and functions.
385A
Bottom Strike
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313,
315 & 643E. US15 and US32D available with 98 Series only.
Bottom Latch
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm) Standard
Adjustable from 355/8" (905mm) to 495/8" (1260mm)
Center case
dimensions
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
Mechanism case
dimensions
2 1/4" x 2 1/4" (57mm x 57mm)
Projection
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Latch bolt
Deadlocking top bolt, 3/4" (19mm) throw
Deadlocking bottom bolt, 1 1/2" (38mm) throw
3
/4" (19mm) maximum, more than 1/4" minimum
Door undercut
Top & bottom
Latch case
4 1/4" x 1 1/2" x 1 1/8" (107mm x 38mm x 28mm)
Vertical rods
Round 2-piece adjustable rods – Top rod adjustable from 6'8"
(2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5/8"
(905 mm) to 49 5/8" (1260 mm). Extension rod kits available for
doors over 8'4" (2533mm).
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
metal doors. Optional 425 SNB available.
Fasteners & sex
bolts (SNB)
Electric options
Mechanical
options
Dogging option
Strikes
30 • Von Duprin 98/99 Series
LX
Latchbolt monitor switch
RX
Pushpad monitor switch
RX2
Double pushpad monitor switch
E
Electric unlocking and locking trim
EL
Electric latch retraction
QEL
Quiet electric latch retraction
SS
Signal switch
CX
Chexit delayed exit
ALK
Alarm exit kit
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
PN
Pneumatic latch retraction
SNB
Sex bolts
SEC
Security screws
SLM
Special laminate material blocking
No mechanical dogging. EL and QEL option available
Top – 338 - Unfinished, Bottom – 385A - Unfinished
CX
ALK
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
EL
SS
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Signal switch
• Signals
unauthorized use
of an opening
• Switch makes
latch bolt
tamper-resistant
QEL
LX
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Latchbolt monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor latch bolt
E (E996L)
RX
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
PN
CON
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
Standard trim
EO
DT
NL
NL-OP
TL
TL-BE
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Thumbturn
Key locks & unlocks
(use with DT trim)
Thumbturn
Blank escutcheon
always operable
(no cylinder)
(use with DT trim)
Product description
9848EO-F
9948EO-F
—
—
9848NL-F
9948NL-F
9848NL-OP-F
9948NL-OP-F
9848TL-F
9948TL-F
9848TL-BE-F
9948TL-BE-F
Trim description
—
990DT
990NL-R/V
110NL-MD
374T X 990DT
374T-BE X 990DT
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
—
(76x360x2mm)
2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
(70x273x21mm)
Escutcheon plate
size
Pull center to center —
5 1/2" (140mm)
5 1/2" (140mm)
—
—
—
Projection
—
2" (51mm)
2" (51mm)
—
3 /4" (83mm)
3 1/4" (83mm)
ANSI function
01
02
03
03
11
—
Cylinder type
—
—
Rim
Rim
1 1/4" Mortise
—
Handing
—
—
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
6
2
2
#425 SNB optional
- HMD req. WD
w/o SLM pkg.
1
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
(not recommended for fire device)
9848L-F
9948L-F
9848L-NL-F
9948L-NL-F
9848L-BE-F
9948L-BE-F
—
—
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
#425 SNB optional
- HMD req. WD
w/o SLM pkg.
2
2
2
2
9848-F/9948-F Concealed vertical rod fire exit device
No outside trim
Exit only
Dummy trim
Pull when dogged
(not recommended for
fire device)
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 31
9849/9949 Concealed vertical cable device
Top latch
338
Top strike
retrofit bracket
9849/9949 Concealed vertical cable device for use on single or double metal doors, UL listed for
panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9849 device has a smooth
mechanism case and the 9949 device has a grooved case. The concealed vertical cable device is
non-handed except when the following device options are used: SD (special dogging), or SS (signal
switch). See opposite page for available outside trim and device functions.
Center
slide
249
Top strike
9849/9949 Concealed vertical cable device
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Center case
dimensions
Mechanism case
dimensions
Projection
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm)
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
2 1/4" x 2 1/4" (57mm x 57mm)
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Latch bolt
Deadlocking top & bottom bolt, 1/2" (13mm) throw
Door undercut
/4" (19mm) maximum
(24231516 spacer block kit needed for 3/4" undercut)
5 13/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm)
Top & bottom
latch case
Vertical cable
Fasteners & sex
bolts (SNB)
Electric options
Mechanical
options
Dogging feature
Dogging option
Strikes
3
/32" (6mm) Diameter stainless steel cables
7
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
metal doors. Optional 425 SNB available.
ALK
Alarm exit kit
CX
Chexit delayed exit
E
Electric unlocking and locking trim
EL
Electric latch retraction
HD-EL Electric latch retraction w/ hex dogging
QEL
Quiet electric latch retraction
*
LX
Latchbolt monitor switch
RX2
Double pushpad monitor switch
RX996L Trim monitor switch
RX
Pushpad monitor switch
RXLC
Pushpad monitor switch - low current
SS
Signal switch
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
LBL Less bottom latch
AX Accessible device (LBL only)
PN Pneumatic latch retraction
SEC
Security screws
SG
Safety glow
SNB
Sex bolts
Hex key dogging standard
CD
Cylinder dogging
SD
Special center case dogging
LD
Less dogging
DI
Dogging indicator
CI
Cylinder dogging indicator
Top - 249 – Unfinished, Bottom – 349 - Unfinished
*For 98/9949 devices, LX switch monitors trim input or electric dogging of EL/QEL devices. LX switch does not monitor
latchbolt condition.
32 • Von Duprin 98/99 Series
349
Bottom strike
Bottom latch
Hex key dogging comes
standard on 9849/9949
concealed vertical cable
devices
CX
RX
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
EL
ALK
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
AX
CON
Accessible device
• UL certified to
meet new 5 lb.
maximum
operating force
requirement
• Exceeds ANSI/
BHMA
requirements
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
PN
DI
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Dogging indicator
• Monitor dogging
status without a
control panel
• Red indicator
light shows
visibility to
dogging from
over 75 feet
CD
QEL
Cylinder dogging
• Replaces hex key
dogging
• Requires
standard 1 1/4"
mortise cylinder
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Standard trim
EO
DT
NL
NL-OP
No outside trim
Exit only
Dummy trim
Pull when dogged
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Product description
9849EO
9949EO
9849DT
9949DT
9849NL
9949NL
9849NL-OP
9949NL-OP
Trim description
—
990DT
990NL-R/V
110NL-MD
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
(76x360x2mm)
—
5 1/2" (140mm)
5 1/2" (140mm)
—
Escutcheon plate
size
Pull center to center —
—
2" (51mm)
2" (51mm)
—
ANSI function
01
02
03
03
Cylinder type
—
—
Rim
Rim
Handing
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
6
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
9849L
9949L
9849L-NL
9949L-NL
9849L-BE
9949L-BE
9849L-DT
9949L-DT
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Optional #425 SNB
quantity for device
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
9849/9949 Concealed vertical cable device
Projection
* Electrified lever operation available
Standard door opening height
Feet
Inches
6'8"
80"
7'
84"
8'
96"
9'
108"
10'
120"
Door opening height
is measured from finished floor
to frame rabbet on door side.
See table on left for standard offering.
Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011.
Von Duprin 98/99 Series • 33
9849-F/9949-F Concealed vertical cable fire exit device
Top latch
9848-F/9948-F Concealed vertical rod fire exit device
338
Top strike
retrofit bracket
9849/9949 Concealed vertical cable device for use on single or double metal doors, UL listed for
panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9849 device has a smooth
mechanism case and the 9949 device has a grooved case. The concealed vertical cable device is
non-handed except when the following device options are used: SD (special dogging), or SS (signal
switch). See opposite page for available outside trim and device functions.
Center
slide
249
Top strike
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
349
Bottom strike
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm) Standard
Center case
dimensions
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
Mechanism case
dimensions
2 1/4" x 2 1/4" (57mm x 57mm)
Projection
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Bottom latch
CX
SS
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Signal switch
• Signals
unauthorized use
of an opening
• Switch makes
latch bolt
tamper-resistant
EL
RX
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
Latch bolt
Deadlocking anti-friction top & bottom bolt, 5/8" (16mm) throw
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Door undercut
/4" (19mm) maximum
(24231516 spacer block kit needed for 3/4" undercut)
5 13/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm)
QEL
E (E996L)
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
AX
CON
Accessible device
• UL certified to
meet new 5 lb.
maximum
operating force
requirement
• Exceeds ANSI/
BHMA
requirements
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
Top & bottom
Latch case
3
/32" (6mm) Diameter stainless steel cables
Vertical cable
7
Fasteners & sex
bolts (SNB)
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
metal doors. Optional 425 SNB available.
Electric options
ALK
Alarm exit kit
CX
Chexit delayed exit
E
Electric unlocking and locking trim
EL
Electric latch retraction
HD-EL Electric latch retraction w/ hex dogging
QEL
Quiet electric latch retraction
*
LX
Latchbolt monitor switch
RX2
Double pushpad monitor switch
RX996L Trim monitor switch
RX
Pushpad monitor switch
RXLC
Pushpad monitor switch - low current
SS
Signal switch
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
LBL Less bottom latch
AX Accessible device (LBL only)
PN
Pneumatic latch retraction
SEC
Security screws
SG
Safety glow
SNB
Sex bolts
No mechanical dogging. EL and QEL option available
Top – 249 - Unfinished, Bottom – 349 - Unfinished
Mechanical
options
Dogging option
Strikes
34 • Von Duprin 98/99 Series
PN
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
*For 98/9949 devices, LX switch monitors trim input or
electric dogging of EL/QEL devices. LX switch does not
monitor latchbolt condition.
Standard trim
DT
NL
NL-OP
No outside trim
Exit only
Dummy trim
Pull when dogged
(not recommended for fire device)
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Product description
9849EO-F
9949EO-F
—
—
9849NL-F
9949NL-F
9849NL-OP-F
9949NL-OP-F
Trim description
—
990DT
990NL-R/V
110NL-MD
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
(76x360x2mm)
—
5 1/2" (140mm)
5 1/2" (140mm)
—
Escutcheon plate
size
Pull center to center —
Projection
—
2" (51mm)
2" (51mm)
—
ANSI function
01
02
03
03
Cylinder type
—
—
Rim
Rim
Handing
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
6
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
(not recommended for fire device)
9849L-F
9949L-F
9849L-NL-F
9949L-NL-F
9849L-BE-F
9949L-BE-F
—
—
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Optional #425 SNB
quantity for device
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
9848-F/9948-F Concealed vertical rod fire exit device
EO
* Electrified lever operation available
Standard door opening height
Feet
Inches
6'8"
80"
7'
84"
8'
96"
9'
108"
10'
120"
Door opening height
is measured from finished floor
to frame rabbet on door side.
See table on left for standard offering.
Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011.
Von Duprin 98/99 Series • 35
9847WDC/9947WDC Wood door concealed vertical rod device
Top Latch
9847WDC/9947WDC Wood door concealed vertical rod device
338
Top Strike
9847WDC/9947WDC Concealed vertical rod device for use on single or double wood doors, UL listed
for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9847WDC device has a smooth
mechanism case and the 9947WDC device has a grooved case. The concealed vertical rod device is
non-handed except when the following device options are used: SD (special dogging), or SS (signal
switch). See opposite page for available outside trim and functions.
Scalp plate – Device is furnished standard with an 8" (203mm) long scalp plate for easy access to
rods.
385A
Bottom Strike
Note: Do not use on pair of doors with 9875/9975.
Finishes – US3, US4, US10, US26, US26D, US28 & 313. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm) Standard
Adjustable from 355/8" (905mm) to 495/8" (1260mm)
Center case
dimensions
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
Mechanism case
dimensions
2 1/4" x 2 1/4" (57mm x 57mm)
Projection
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Latch bolt
Deadlocking top bolt, 5/8" (16mm) throw
Door undercut
1
Top & bottom
Latch case
3 /4" x 1 /2" x 1" (95mm x 38mm x 25mm)
Vertical rods
Round 2-piece adjustable rods – Top rod adjustable from 6'8"
(2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5/8"
(905 mm) to 49 5/8" (1260 mm). Extension rod kits available for
doors over 8'4" (2533mm).
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
wood doors. 425 SNB required on wood doors without SLM
blocking.
LX
Latchbolt monitor switch
RX
Pushpad monitor switch
RX2
Double pushpad monitor switch
E
Electric unlocking and locking trim
EL
Electric latch retraction
QEL
Quiet electric latch retraction
SS
Signal switch
CX
Chexit delayed exit
ALK
Alarm exit kit
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
PN
Pneumatic latch retraction
PL
Pullman latch
LBR
Less bottom rod
SNB
Sex bolts
SEC
Security screws
Hex key dogging standard
Fasteners & sex
bolts (SNB)
Electric options
Mechanical
options
Dogging feature
Dogging option
Strikes
36 • Von Duprin 98/99 Series
/4" (7mm) maximum
3
1
CD
Cylinder dogging
LD
Less dogging
DI
Dogging indicator
CI
Cylinder dogging indicator
Top – 338 - Unfinished, Bottom – 385A - Unfinished
283 Top Strike
for use with wood
frames
Bottom Latch
Hex key dogging comes
standard on 9847/9947
Wood door concealed
vertical rod devices
CX
ALK
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
EL
PL
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Pullman latch
• Not for use with
Fire Exit
Hardware
QEL
LX
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Latchbolt monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor latch bolt
E (E996L)
RX
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
PN
CON
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
Standard trim
EO
DT
NL
NL-OP
TL
TL-BE
Dummy trim
Pull when dogged
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Thumbturn
Key locks & unlocks
(use with DT trim)
9847WDC-EO
9947WDC-EO
9847WDC-DT
9947WDC-DT
9847WDC-NL
9947WDC-NL
9847WDCNL-OP
9947WDCNL-OP
9847WDC-TL
9947WDC-TL
9847WDC-TL-BE
9947WDC-TL-BE
—
990DT
990NL-R/V
110NL-WD
376TWDC x
990DT
376TWDC-BE x
990DT
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
—
(76x360x2mm)
Pull center to center —
5 1/2" (140mm)
5 1/2" (140mm)
—
—
Projection
—
2" (51mm)
2" (51mm)
—
2" (51mm)
2" (51mm)
ANSI function
01
02
03
03
11 or 12
16
Cylinder type
—
—
Rim
Rim
1 1/4" Mortise
—
—
—
—
6
2
2
Product description
Trim description
Escutcheon plate
size
Handing
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
Optional #425 SNB
quantity for device
2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
(70x273x21mm)
—
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
9847WDC-L
9947WDC-L
9847WDC-L-NL
9947WDC-L-NL
9847WDC-L-BE
9947WDC-L-BE
9847WDC-L-DT
9947WDC-L-DT
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
9847WDC/9947WDC Wood door concealed vertical rod device
No outside trim
Exit only
Thumbturn
Blank escutcheon
always operable
(no cylinder)
(use with DT trim)
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 37
9847WDC-F/9947WDC-F Wood door concealed vertical rod fire device
Top Latch
9847WDC-F/9947WDC-F Wood door concealed vertical rod fire device
338
Top Strike
9847WDC-F/9947WDC-F Fire exit concealed vertical rod device for use on pairs of doors up to 8' x
9' 3" (2438mm x 2819mm) double wood doors, UL listed for fire exit hardware. See page 72 for
detailed information on UL listed fire exit hardware label and door opening size information. Devices
are ANSI A156.3 – 2001 Grade 1. The 9847WDC-F device has a smooth mechanism case and the
9947WDC-F device has a grooved case. The concealed vertical rod device is non-handed except
when the following device options are used: SS (signal switch). See Opposite page for available
outside trim and functions.
Scalp Plate – Device is furnished standard with an 8" (203mm) long scalp plate for easy access to
rods. Note: Do not use on pair of doors with 9875-F/9975-F.
Finishes – US3, US4, US10, US26, US26D, US28 & 313. US15 and US32D available with 98 Series
only.
Specifications
Device functions
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
Device lengths
2'
3'
4'
Device centerline
from finished floor
395/8" (1006 mm) Standard
Center case
dimensions
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
Mechanism case
dimensions
2 1/4" x 2 1/4" (57mm x 57mm)
Projection
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
2" (610 mm) Door size (shipped less UL label)
2'4' to 3' (711mm to 914 mm) Door size
2'10" to 4' (864 mm to 1219 mm) Door size
Latch bolt
Deadlocking top & bottom bolt, 5/8" (16mm) throw
385A
Bottom Strike
283 Top Strike
for use with wood
frames
Bottom Latch
CX
ALK
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
EL
LX
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Latchbolt monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor latch bolt
Door undercut
1
Top & bottom
Latch case
3 3/4" x 1 1/2" x 1" (95mm x 38mm x 25mm)
QEL
RX
Vertical rods
Round 2-piece adjustable rods – Top rod adjustable from 6'8"
(2027mm) to 8'4"(2533mm). Bottom rod adjustable 35 5/8"
(905 mm) to 49 5/8" (1260 mm). Extension rod kits available for
doors over 8'4" (2533mm).
Fasteners & sex
bolts (SNB)
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
wood doors. 425 SNB required on wood doors without SLM
blocking.
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
Electric options
LX
RX
RX2
E
EL
QEL
SS
CX
ALK
WP-RX
CON
Latchbolt monitor switch
Pushpad monitor switch
Double pushpad monitor switch
Electric unlocking and locking trim
Electric latch retraction
Quiet electric latch retraction
Signal switch
Chexit delayed exit
Alarm exit kit
Waterproof request to exit
Allegion Connect
E (E996L)
CON
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
Mechanical
options
GBK PN
PL
LBR
SNB
SEC
Glass bead kit
Pneumatic latch retraction
Pullman latch
Less bottom rod
Sex bolts
Security screws
Dogging option
No mechanical dogging. EL and QEL option available
Strikes
Top – 338 - Unfinished, Bottom – 385A - Unfinished
38 • Von Duprin 98/99 Series
/4" (7mm) maximum
PN
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
Standard trim
EO
Trim description
NL
NL-OP
TL
TL-BE
No outside trim
Exit only
Dummy trim
Pull when dogged
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Thumbturn
Key locks & unlocks
(use with DT trim)
Thumbturn
Blank escutcheon
always operable
(no cylinder)
(use with DT trim)
9847WDC-EO-F
9847WDC-DT-F
9847WDC-NL-F
9847WDCNL-OP-F
9847WDC-TL-F
9847WDC-TL-BE-F
9947WDC-EO-F
9947WDC-DT-F
9947WDC-NL-F
9947WDCNL-OP-F
9947WDC-TL-F
9947WDC-TL-BE-F
110NL-WD
376TWDC x
990DT
376TWDC-BE x
990DT
—
990DT
990NL-R/V
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
—
(76x360x2mm)
Pull center to center —
5 1/2" (140mm)
5 1/2" (140mm)
—
—
Projection
—
2" (51mm)
2" (51mm)
—
2" (51mm)
2" (51mm)
ANSI function
01
02
03
03
11
—
Cylinder type
—
—
Rim
Rim
1 1/4" Mortise
—
Handing
—
—
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x996L-NL
x696NL
x697NL
6
2
2
6
2
2
Escutcheon plate
size
#425 SNB optional
- HMD req. WD
w/o SLM pkg.
2 3/4" x 10 3/4" x 27/32" 2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
(70x273x21mm)
—
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
9847WDC-L-F
9947WDC-L-F
9847WDC-L-NL-F
9947WDC-L-NL-F
9847WDC-L-BE-F
9947WDC-L-BE-F
9847WDC-L-DT-F
9947WDC-L-DT-F
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
#425 SNB optional
- HMD req. WD
w/o SLM pkg.
2
2
2
2
9847WDC-F/9947WDC-F Wood door concealed vertical rod fire device
Product description
DT
* Electrified lever operation available
Notes
Von Duprin 98/99 Series • 39
9849WDC/9949WDC Wood door concealed vertical cable device
Top latch
9849WDC/9949WDC Wood door concealed vertical cable device
338
Top strike
retrofit bracket
9849WDC/9949WDC Concealed vertical cable device for use on single or double wood doors, UL
listed for panic exit hardware. Devices are ANSI A156.3 – 2001 Grade 1. The 9847WDC device has a
smooth mechanism case and the 9947WDC device has a grooved case. The concealed vertical cable
device is non-handed except when the following device options are used: SD (special dogging), or SS
(signal switch). See Opposite page for available outside trim and functions.
Scalp Plate – Device is furnished standard with an 8" (203mm) long scalp plate for easy access to
cables.
Center
slide
249
Top strike
Note: Do not use on pair of doors with 9975 devices.
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Center case
dimensions
Mechanism case
dimensions
Projection
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
2 1/4" x 2 1/4" (57mm x 57mm)
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Latch bolt
Deadlocking top & bottom bolt. 1 1/2" (38mm) throw
Door undercut
/4" (19mm) maximum
(24231516 spacer block kit needed for 3/4" undercut)
5 13/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm)
Top & bottom
Latch case
Vertical cables
Fasteners & sex
bolts (SNB)
Electric options
Mechanical
options
Dogging feature
Dogging option
Strikes
40 • Von Duprin 98/99 Series
349
Bottom strike
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm) Standard
3
/32" (6mm) Diameter stainless steel cables
7
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
wood doors. 425 SNB required on wood doors without SLM
blocking.
ALK
Alarm exit kit
CX
Chexit delayed exit
E
Electric unlocking and locking trim
EL
Electric latch retraction
HD-EL Electric latch retraction w/ hex dogging
QEL
Quiet electric latch retraction
*
LX
Latchbolt monitor switch
RX2
Double pushpad monitor switch
RX996L Trim monitor switch
RX
Pushpad monitor switch
RXLC
Pushpad monitor switch - low current
SS
Signal switch
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
LBL Less bottom latch
PN
Pneumatic latch retraction
SEC
Security screws
SG
Safety glow
SNB
Sex bolts
Hex key dogging standard
CD
Cylinder dogging
SD
Special center case dogging
LD
Less dogging
DI
Dogging indicator
CI
Cylinder dogging indicator
Top - 249 – Unfinished, Bottom – 349 - Unfinished
Bottom latch
Hex key dogging comes
standard on 9849/9949
Wood door concealed
vertical cable devices
CX
ALK
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
EL
RX
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
QEL
LX
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Latchbolt monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor latch bolt
E (E996L)
CON
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
PN
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
*For 98/9949 devices, LX switch
monitors trim input or electric
dogging of EL/QEL devices. LX
switch does not monitor
latchbolt condition.
Standard trim
DT
NL
NL-OP
No outside trim
Exit only
Dummy trim
Pull when dogged
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Product description
9849WDC-EO
9949WDC-EO
9849WDC-DT
9949WDC-DT
9849WDC-NL
9949WDC-NL
9849WDC-NL-OP
9949WDC-NL-OP
Trim description
—
990DT
990NL-R/V
110NL-WD
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
(76x360x2mm)
—
5 1/2" (140mm)
5 1/2" (140mm)
—
Escutcheon plate
size
Pull center to center —
Projection
—
2" (51mm)
2" (51mm)
—
ANSI function
01
02
03
03
Cylinder type
—
—
Rim
Rim
Handing
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
6
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
9849WDC-L
9949WDC-L
9849WDC-L-NL
9949WDC-L-NL
9849WDC-L-BE
9949WDC-L-BE
9849WDC-L-DT
9949WDC-L-DT
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Optional #425 SNB
quantity for device
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
* Electrified lever operation available
9849WDC/9949WDC Wood door concealed vertical cable device
EO
Standard door opening height
Feet
Inches
6'8"
80"
7'
84"
8'
96"
9'
108"
10'
120"
Door opening height
is measured from finished floor
to frame rabbet on door side.
See table on left for standard offering.
Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011.
Von Duprin 98/99 Series • 41
9849WDC-F/9949WDC-F Wood door concealed vertical cable fire device
Top latch
9847WDC-F/9947WDC-F Wood door concealed vertical rod fire device
338
Top strike
retrofit bracket
9849WDC-F/9949WDC-F Fire exit concealed vertical cable device for use on pairs of doors up to 8'
x 9' 3" (2438mm x 2819mm) double wood doors, UL listed for fire exit hardware. See page 72 for
detailed information on UL listed fire exit hardware label and door opening size information. Devices are
ANSI A156.3 – 2001 Grade 1. The 9849WDC-F device has a smooth mechanism case and the
9949WDC-F device has a grooved case. The concealed vertical cable device is non-handed except
when the following device options are used: SS (signal switch). See opposite page for available outside
trim and functions.
Center
slide
249
Top strike
Scalp Plate – Device is furnished standard with an 8" (203mm) long scalp plate for easy access to
cables.
Note: Do not use on pair of doors with 9975 devices.
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Center case
dimensions
Mechanism case
dimensions
Projection
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm) Standard
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
2 1/4" x 2 1/4" (57mm x 57mm)
Pushbar neutral – 3 /16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
13
Latch bolt
Deadlocking top & bottom bolt, 1 1/2" (38mm) throw
Door undercut
/4" (19mm) maximum
(24231516 spacer block kit needed for 3/4" undercut)
5 13/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm)
Top & bottom
Latch case
Vertical cables
Fasteners & sex
bolts (SNB)
Electric options
Mechanical
options
Dogging option
Strikes
42 • Von Duprin 98/99 Series
3
/32" (6mm) Diameter stainless steel cables
7
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
wood doors. 425 SNB required on wood doors without SLM
blocking.
ALK
Alarm exit kit
CX
Chexit delayed exit
E
Electric unlocking and locking trim
EL
Electric latch retraction
HD-EL Electric latch retraction w/ hex dogging
QEL
Quiet electric latch retraction
*
LX
Latchbolt monitor switch
RX2
Double pushpad monitor switch
RX996L Trim monitor switch
RX
Pushpad monitor switch
RXLC
Pushpad monitor switch - low current
SS
Signal switch
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
LBL Less bottom latch
PN
Pneumatic latch retraction
SEC
Security screws
SG
Safety glow
SNB
Sex bolts
SLM
Special laminate material blocking
No mechanical dogging. EL and QEL option available
Top – 249 - Unfinished, Bottom – 349 - Unfinished
349
Bottom strike
Bottom latch
CX
ALK
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
EL
LX
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Latchbolt monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor latch bolt
QEL
RX
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
E (E996L)
CON
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
PN
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
*For 98/9949 devices, LX switch monitors trim input or
electric dogging of EL/QEL devices. LX switch does not
monitor latchbolt condition.
Standard trim
EO
DT
NL
NL-OP
No outside trim
Exit only
Dummy trim
Pull when dogged
(not recommended for fire device)
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Product description
9849WDC-EO-F
9949WDC-EO-F
—
—
9849WDC-NL-F
9949WDC-NL-F
9849WDC-NL-OP-F
9949WDC-NL-OP-F
Trim description
—
990DT
990NL-R/V
110NL-WD
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
(76x360x2mm)
—
5 1/2" (140mm)
5 1/2" (140mm)
—
Escutcheon plate
size
Pull center to center —
Projection
—
2" (51mm)
2" (51mm)
—
ANSI function
01
02
03
03
Cylinder type
—
—
Rim
Rim
Handing
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x996L-NL
x696NL
x697NL
6
2
2
6
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
(not recommended for fire device)
9849WDC-L-F
9949WDC-L-F
9849WDC-L-NL-F
9949WDC-L-NL-F
9849WDC-L-BE-F
9949WDC-L-BE-F
—
—
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Optional #425 SNB
quantity for device
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
* Electrified lever operation available
Standard door opening height
Feet
Inches
6'8"
80"
7'
84"
8'
96"
9'
108"
10'
120"
Door opening height
is measured from finished floor
to frame rabbet on door side.
See table on left for standard offering.
Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011.
Von Duprin 98/99 Series • 43
9850WDC/9950WDC Wood door concealed vertical cable device
Top latch
9850WDC/9950WDC Wood door concealed vertical cable device
338
Top strike
retrofit bracket
9850WDC/9950WDC Concealed vertical cable device for use on single or double wood doors,
UL listed for panic exit hardware. Devices are ANSI A156.3 – 2008 Grade 1. The 9850WDC device has
a smooth mechanism case and the 9950WDC device has a grooved case. The concealed vertical cable
device is non-handed except when the following device options are used: SD (special dogging),
or SS (signal switch). See Opposite page for available outside trim and functions.
Scalp Plate – Device is furnished standard with an 15" (381 mm) long scalp plate for easy access
to cables.
Center
slide
249
Top strike
Note: Do not use on pair of doors with 9975 devices.
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315
& 643E. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Center case
dimensions
Mechanism case
dimensions
Projection
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
2 1/4" x 2 1/4" (57mm x 57mm)
Pushbar neutral – 3 13/16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
Latch bolt
Deadlocking top & bottom bolt. 1 1/2" (38mm) throw
Door undercut
3
Top & bottom
Latch case
Vertical cables
5 13/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm)
Fasteners & sex
bolts (SNB)
Electric options
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
wood doors.
ALK
Alarm exit kit
CX
Chexit delayed exit
E
Electric unlocking and locking trim
EL
Electric latch retraction
HD-EL Electric latch retraction w/ hex dogging
QEL
Quiet electric latch retraction
*
LX
Latchbolt monitor switch
RX2
Double pushpad monitor switch
RX996L Trim monitor switch
RX
Pushpad monitor switch
RXLC
Pushpad monitor switch - low current
SS
Signal switch
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
LBL Less bottom latch
PN
Pneumatic latch retraction
SEC
Security screws
SG
Safety glow
SNB
Sex bolts
Hex key dogging standard
CD
Cylinder dogging
SD
Special center case dogging
LD
Less dogging
DI
Dogging indicator
CI
Cylinder dogging indicator
Top - 249 – Unfinished, Bottom – 450 - Unfinished
Mechanical
options
Dogging feature
Dogging option
Strikes
44 • Von Duprin 98/99 Series
450
Bottom strike
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm) Standard
/4" (19mm) maximum
/32" (6mm) Diameter stainless steel cables
7
Bottom latch
Hex key dogging comes
standard on 9850/9950
Wood door concealed
vertical cable devices
CX
ALK
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
EL
RX
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
QEL
LX
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Latchbolt monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor latch bolt
E (E996L)
CON
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
PN
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
*For 98/9950WDC devices, LX
switch monitors trim input or
electric dogging of EL/QEL
devices. LX switch does not
monitor latchbolt condition.
Standard trim
DT
NL
NL-OP
No outside trim
Exit only
Dummy trim
Pull when dogged
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Product description
9850WDC-EO
9950WDC-EO
9850WDC-DT
9950WDC-DT
9850WDC-NL
9950WDC-NL
9850WDC-NL-OP
9950WDC-NL-OP
Trim description
—
990DT
990NL-R/V
110NL-WD
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
(76x360x2mm)
—
5 1/2" (140mm)
5 1/2" (140mm)
—
Escutcheon plate
size
Pull center to center —
Projection
—
2" (51mm)
2" (51mm)
—
ANSI function
01
02
03
03
Cylinder type
—
—
Rim
Rim
Handing
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x696NL
x697NL
6
2
2
6
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
9850WDC-L
9950WDC-L
9850WDC-L-NL
9950WDC-L-NL
9850WDC-L-BE
9950WDC-L-BE
9850WDC-L-DT
9950WDC-L-DT
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Optional #425 SNB
quantity for device
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
* Electrified lever operation available
9850WDC/9950WDC Wood door concealed vertical cable device
EO
Standard door opening height
Feet
Cable tolerance
6'8" - 7'
72" - 84"
7'1" - 8'
85" - 96"
8'1" - 9'
97" - 108"
9'1" - 10'
109" - 120"
Door opening height
is measured from finished floor
to frame rabbet on door side.
See table on left for standard offering.
Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011.
Von Duprin 98/99 Series • 45
9850WDC-F/9950WDC-F Wood door concealed vertical cable fire device
Top latch
9850WDC-F/9950WDC-F Wood door concealed vertical rod fire device
338
Top strike
retrofit bracket
9850WDC-F/9950WDC-F Fire exit concealed vertical cable device for use on pairs of doors up to 8'
x 9' 3" (2438mm x 2819mm) double wood doors, UL listed for fire exit hardware. See page 72 for
detailed information on UL listed fire exit hardware label and door opening size information. Devices are
ANSI A156.3 – 2001 Grade 1. The 9850WDC-F device has a smooth mechanism case and the
9950WDC-F device has a grooved case. The concealed vertical cable device is non-handed except
when the following device options are used: SS (signal switch). See opposite page for available outside
trim and functions.
Center
slide
249
Top strike
Scalp Plate – Device is furnished standard with an 15" (381 mm) long scalp plate for easy access to
cables.
Note: Do not use on pair of doors with 9975 devices.
Finishes – US3, US3A, US4, US4A, US10, US26, US26D, US26D-AM Antimicrobial, US28, 313, 315 &
643E. US15 and US32D available with 98 Series only.
Specifications
Device functions
Device lengths
Device centerline
from finished floor
Center case
dimensions
Mechanism case
dimensions
Projection
Device ships EO/DT/NL. Field selectable. For TP, K or L remove
NL drive screw from device.
2'
2" (610 mm) Door size (shipped less UL label)
3'
2'4' to 3' (711mm to 914 mm) Door size
4'
2'10" to 4' (864 mm to 1219 mm) Door size
395/8" (1006 mm) Standard
8" x 2 3/4" x2 3/8" (203mm x 70mm x 60mm)
2 1/4" x 2 1/4" (57mm x 57mm)
Pushbar neutral – 3 /16" (97 mm)
Pushbar depressed – 3 1/16" (78 mm)
13
Latch bolt
Deadlocking top & bottom bolt, 1 1/2" (38mm) throw
Door undercut
3
Top & bottom
Latch case
Vertical cables
5 13/16" x 1 1/4" x 1 7/16" (147mm x 32mm x 37mm)
Fasteners & sex
bolts (SNB)
Electric options
Includes screw pack for 1 3/4" (44mm) to 2 1/4" (57mm) thick
wood doors.
ALK
Alarm exit kit
CX
Chexit delayed exit
E
Electric unlocking and locking trim
EL
Electric latch retraction
HD-EL Electric latch retraction w/ hex dogging
QEL
Quiet electric latch retraction
*
LX
Latchbolt monitor switch
RX2
Double pushpad monitor switch
RX996L Trim monitor switch
RX
Pushpad monitor switch
RXLC
Pushpad monitor switch - low current
SS
Signal switch
WP-RX Waterproof request to exit
CON
Allegion Connect
GBK Glass bead kit
LBL Less bottom latch
PN
Pneumatic latch retraction
SEC
Security screws
SG
Safety glow
SNB
Sex bolts
SLM
Special laminate material blocking
No mechanical dogging. EL and QEL option available
Top – 249 - Unfinished, Bottom – 450 - Unfinished
Mechanical
options
Dogging option
Strikes
46 • Von Duprin 98/99 Series
/4" (19mm) maximum
/32" (6mm) Diameter stainless steel cables
7
450
Bottom strike
Bottom latch
CX
ALK
Chexit delayed
exit
• Meets NFPA 101
requirements
• Self-contained
controls, locking,
alarm
Alarm exit kit
• Unauthorized
opening triggers
85-decibel horn
• Set in armed or
disarmed mode
by key
EL
LX
Electric latch
retraction
• Enables remote
unlatching
• Alternative to
manual dogging
Latchbolt monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor latch bolt
QEL
RX
Quiet electric
latch retraction
• Bolt retraction via
switch
• Converts exit
door to push-pull
operation
Pushpad monitor
switch
• Signals use of an
opening
• SPDT switch to
monitor pushpad
E (E996L)
CON
Electrified
breakaway lever
• Electrified remote
locking/unlocking
• Standard in fail
safe condition
Allegion
Connectors
• Common
connectors to
connect various
door hardware all
the way to the
power supply
PN
Pneumatic latch
retraction
• For areas where
electrical devices
banned
• Special linkage
for mechanical or
pneumatic
dogging
*For 98/9950 devices, LX switch monitors trim input or
electric dogging of EL/QEL devices. LX switch does not
monitor latchbolt condition.
Standard trim
EO
DT
NL
NL-OP
No outside trim
Exit only
Dummy trim
Pull when dogged
(not recommended for fire device)
Night latch
Key retracts latchbolt
Night latch
Key retracts latchbolt
optional pull required
Product description
9850WDC-EO-F
9950WDC-EO-F
—
—
9850WDC-NL-F
9950WDC-NL-F
9850WDC-NL-OP-F
9950WDC-NL-OP-F
Trim description
—
990DT
990NL-R/V
110NL-WD
—
3" x 14 13/16" x 3/32"
(76x360x2mm)
3" x 14 13/16" x 3/32"
(76x360x2mm)
—
5 1/2" (140mm)
5 1/2" (140mm)
—
Escutcheon plate
size
Pull center to center —
Projection
—
2" (51mm)
2" (51mm)
—
ANSI function
01
02
03
03
Cylinder type
—
—
Rim
Rim
Handing
—
—
—
—
Optional trim
x990EO
x996EO
x996K-DT
x996L-DT
x996L-DT
x696DT
x697DT
x996K-NL
x996L-NL
x996L-NL
x696NL
x697NL
6
2
2
6
L
L-NL
L-BE
L-DT
Lever
Key locks & unlocks
Lever – night latch
Key retracts latchbolt
Lever – blank escutcheon
Always operable (no cylinder)
Lever dummy trim
pull when dogged
(not recommended for fire device)
9850WDC-L-F
9950WDC-L-F
9850WDC-L-NL-F
9950WDC-L-NL-F
9850WDC-L-BE-F
9950WDC-L-BE-F
—
—
Trim description
996L-R/V*
996L-NL-R/V
996L-BE-R/V*
996L-DT
Escutcheon plate
size
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
2 3/4" x 10 3/4" x 27/32"
(70x273x21mm)
Optional #425 SNB
quantity for device
Product description
Pull center to center —
—
—
—
Projection
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
2 7/8" (73mm)
ANSI function
08
03
14
02
Cylinder type
Rim
Rim
—
—
Handing
Handed/Reversible
Handed/Reversible
Handed/Reversible
Handed/Reversible
Optional #425 SNB
quantity for device
2
2
2
2
* Electrified lever operation available
Standard door opening height
Feet
Cable tolerance
6'8" - 7'
72" - 84"
7'1" - 8'
85" - 96"
8'1" - 9'
97" - 108"
9'1" - 10'
109" - 120"
Door opening height
is measured from finished floor
to frame rabbet on door side.
See table on left for standard offering.
Note: Non-standard sizes available with extended lead time. Consult Customer Care for more information 1-877-671-7011.
Von Duprin 98/99 Series • 47
98/99 Optional trim
Knob, exit only and thumbpiece trim – 990 & 996K
K-NL
K
Knob
Key locks & unlocks
Trim
996K
description
Knob – night latch
Key retracts
latchbolt
996K-NL
K-BE
Knob – blank
escutcheon
Always operable
(no cylinder)
996K-BE
K-DT
Knob – dummy
trim
Pull when dogged
996K-DT
EO
Exit only plate
996EO
TP
Thumbpiece
Key locks &
unlocks
990TP
TP-BE
EO
Thumbpiece
blank
escutcheon
Always operable
(no cylinder)
Exit only plate
990TP-BE
990EO
Escutcheon 23/4" x 103/4" x 27/32" 23/4" x 103/4" x 27/32" 23/4" x 103/4" x 27/32" 23/4" x 103/4" x 27/32" 3" x 143/16" x 3/32" 3" x 143/16" x 3/32" 3" x 143/16" x 3/32" 3" x 143/16" x 3/32"
plate size
(70x273x21mm) (70x273x21mm) (70x273x21mm) (70x273x21mm) (76x360x2mm) (76x360x2mm) (76x360x2mm) (76x360x2mm)
Pull center
to center
—
—
—
—
—
51/2" (140mm)
51/2" (140mm)
51/2" (140mm)
Projection
31/4" (83mm)
31/4" (83mm)
31/4" (83mm)
31/4" (83mm)
—
2" (51mm)
2" (51mm)
Z
ANSI
function
08
09
14
02
01
05
14
14
Rim or
vertical rod Rim
device
Rim
—
—
—
Rim
—
—
Mortise lock 1
1 /4" Mortise
device
11/4" Mortise
—
11/4" Mortise
—
—
Handing
—
—
—
—
—
—
—
—
#425 SNB
optionalHMD req.
WD w/o
SLM pkg.
2
2
2
2
2
2
2
2
#825 SNB
req. WD w/o
SLM pkg F 2
Rim device
ONLY
2
2
2
2
2
2
2
#425 SNB
2
req. w/499F
2
2
2
2
2
2
2
Trim options
Cylinder
type
48 • Von Duprin 98/99 Series
98/99 Optional trim
Optional trims – 696
DT
NL
TP
TP-BE
Dummy trim
Pull when dogged
(not recomended for fire device)
Night latch
Key retracts latchbolt
Thumbpiece
Key locks & unlocks
Trim description
696DT
696NL
696TP
696TP-BE
Escutcheon plate size
23/4" x 103/4" x 27/32"
(70x273x21mm)
23/4" x 103/4" x 27/32"
(70x273x21mm)
15/8" x 131/2" x 3/16"
(41x343x5mm)
15/8" x 131/2" x 3/16"
(41x343x5mm)
Pull center to center
51/2" (140mm)
51/2" (140mm)
51/2" (140mm)
51/2" (140mm)
Projection
2 /6" (52mm)
2 /6" (52mm)
2 /6" (52mm)
2 1/6" (52mm)
ANSI function
02
03
05
15
Rim or vertical
rod device
—
Rim
Rim
—
1
1
1
Thumbpiece – blank
escutcheon
Always operable (no cylinder)
Cylinder type
—
11/4" Mortise
11/4" Mortise
—
—
—
—
—
#425 SNB optional-HMD req.
WD w/o SLM pkg.
2
2
2
2
#825 SNB req. WD w/o SLM
pkg F Rim device ONLY
2
2
2
2
#425 SNB req. w/499F
2
2
2
2
Trim options
Mortise lock device
Handing
Optional trims – 697
DT
NL
TP
TP-BE
(3/4"
diameter
pull) (19mm)
(3/4"
diameter
pull) (19mm)
Dummy trim
Pull when dogged
(not recomended for fire device)
Night latch
Key retracts latchbolt
Thumbpiece
Key locks & unlocks
Trim description
697DT
697NL
697TP
697TP-BE
Escutcheon plate size
23/4" x 103/4" x 27/32"
(70x273x21mm)
23/4" x 103/4" x 27/32"
(70x273x21mm)
15/8" x 131/2" x 3/16"
(41x343x5mm)
23/4" x 103/4" x 27/32"
(70x273x21mm)
Pull center to center
51/2" (140mm)
51/2" (140mm)
51/2" (140mm)
51/2" (140mm)
Projection
3" (76mm)
3" (76mm)
3" (76mm)
3" (76mm)
ANSI function
02
03
05
15
—
Rim
Rim
—
Thumbpiece –
blank escutcheon
Always operable (no cylinder)
Cylinder type
Rim or vertical
rod device
Mortise lock device
—
11/4" Mortise
11/4" Mortise
—
Handing
—
—
—
—
#425 SNB optional-HMD req.
WD w/o SLM pkg.
2
2
2
2
#825 SNB req. WD w/o SLM
pkg F Rim device ONLY
2
2
2
2
#425 SNB req. w/499F
2
2
2
2
Von Duprin 98/99 Series • 49
98/99 Optional trim
E996L Electrified breakaway lever
392-7 Offset pull
The 392-7 Offset pull is 3/4₄" round stainless
steel, with a 7" center to center which matches
the 98/99 center case. Often used with a night
latch operation. 3 1/2" (89mm) offset with 1 1/2₂"
(38mm) clearance.
E996L Electrified lever trim provides
remote locking and unlocking.
Furnished standard in fail safe (FS)
condition, can be field converted to
fail secure (FSE) where allowed.
E996L is furnished standard with
cylinder operation for nightlatch (NL)
function, or with blank
escutcheon (BE).
Specification:
solenoid –
continuous duty 24VDC
Solenoid draw –
0.22 amp.
Vandal resistant trim: IVES VR910 & VR914 Series
VR910 grip coated in black plastisol for softer
touch and resilience to temperature extremes.
Grip designed for comfortable operation.
VR914 grip in all stainless steel.
Features:
•Stainless steel construction, 11 gauge
(0.120" thick)
To order, specify:
1. Use “E” prefix, example
E996L. When ordering with the exit device specify trim
series with prefix “E”, example 9927L-BE 3' US26D E996.
Trim options
2. Device type, R/V (rim/surface vertical rod/concealed
vertical rod) or M (mortise).
3. RHR furnished standard if not specified, field reversible.
4. Lever style (06 lever furnished standard).
Other levers, no extra charge.
•Finish: US32D, only
•Thru-bolts and rugged mounting screws for
maximum fastening strength.
•Built-in lock protector prevents vandalism to
mortise latchbolt (available on certain models).
•Extra-tough stainless steel cylinder collar prevents pipe wrench
or similar tool from damaging cylinder. Tapered design
prevents side impacts from transferring directly to cylinder.
Collar spins freely.
•Furnished with mounting screws for door thicknesses
of 1 3/4" to 2 1/4"
HL6 Hospital pull
Von Duprin and Glynn-Johnson have collaborated on
an exit device trim that answers the problem of
accessibility and performance. Using the Von Duprin
98/9975 mortise lock exit device along with the
Glynn-Johnson HL6 push/pull latch, Allegion has
created an exit device with mortise lock durability
that utilizes a fully ADA compliant Pull paddle trim.
The 98/9975HL device is available in all standard
architectural finishes. Consult the Glynn-Johnson
catalog for complete product information.
Model
For use with
VR910DT & VR914DT
98/99 Rim or
51/2" (133mm) w
vertical rod device x 11" (279mm) h
VR910NL & VR914NL
98/99 Rim or
51/2" (133mm) w
vertical rod device x 11" (279mm) h
VR910M-DT & VR914M-DT
9875/9975
Mortise device
7 1/4" (184mm) w
x 11" (279mm) h
VR910M-NL & VR914M-NL
Handing required
9875/9975
Mortise device
7 1/4" (184mm) w
x 11" (279mm) h
Size
•Meets ANSI/BHMA 156.13, Trim security test and
California State Accessibility Standards Title 24.
•1 1/2" (38mm) clearence from grip to door,
total projection 1 7/8" (48mm)
•Consult the IVES catalog for complete product information.
50 • Von Duprin 98/99 Series
98/99 Optional trim
This page intentionally left blank
Trim options
Von Duprin 98/99 Series • 51
Schlage AD-Series
AD-Series adaptable electronic locks
Standalone locks are a cost-effective solution for doors that do
not require real-time monitoring. The AD-Series standalone
solution provides:
There are a variety of options that allow you
to select the AD-Series electronic lock that’s
right for you, and a wide selection of
features that can be configured in the field
to further customize each opening. When
your needs change in the future, the
innovative modular design of the AD-Series
allows you to easily upgrade the credential
reader or networking option, and adapt to
emerging technologies using your existing
chassis – all without taking the lock off the door. This means
that you can be confident that your choice of the AD-Series is
right for today, and that your investment will be protected into
the future.
•Upgradability
•Improved credential management
•Audit trail reports
Schlage offers two AD-Series standalone solutions to fit your
environment:
AD-200 Access rights are stored on the lock
AD-250 Access rights are stored on the magnetic stripe credential
Chassis
•Cylindrical
•Mortise
•Mortise deadbolt
•Exit trim*
•Classroom/Storeroom
AD-Series electronic locks are compatible with many different
brands and technologies of credentials.
•Office
•Apartment
•Multi-technology
(reads 125 kHz prox and 1
3.56 MHz smart)
Locking functions
Credential reader options
Trim options
Standalone
The AD-Series was designed to be the right choice for today,
and is ready to adapt to whatever the future
holds.
+ KEYPAD
•Privacy
Lever styles
• Magnetic stripe
(insertion)
+ KEYPAD
Sparta Rhodes
Athens
Tubular
Warm Tone Finishes
•Magnetic stripe
(swipe)
+ KEYPAD
605
Bright brass
606 Satin brass
612
Satin bronze
643e
Aged bronze
Cool Tone Finishes
•Keypad
Communications options
Networked
In facilities where increased monitoring and control are needed,
a networked solution is essential. The AD-Series networked
options feature:
619 625 626626AM
Satin nickel
Bright
Satin chrome
Satin chrome
chromewith antimicrobial
Certifications
•ANSI/BMHA A156.25
•ADA
•ANSI/BHMA Grade 1
•FCC part 15
•Open architecture platform
•UL 294 Listed
•RoHS
•Acceptable reader technology
•UL 10C
•FIPS 201-1 (AD-301 and AD-401)
•Real-time monitoring
The AD-Series networked lock is available in either a wireless or
hardwired configuration to fit your application needs.
AD-300 Networked hardwired locks
AD-301 Networked hardwired FIPS 201-1 compliant locks
AD-400 Networked wireless locks
AD-401 Networked wireless FIPS 201-1 compliant locks
52 • Von Duprin 98/99 Series
Complete your system
Complete your AD-Series system with readers and credentials,
biometric hand geometry readers, system components, HHD
programming device and other wireless accessories.
*See AD-Series exit trim compatibility Datasheet for complete list of compatability by
manufacturer.
Schlage CO-Series
CO-Series electronic locks from Schlage
In the world of standalone electronic locks, nothing compares to
the CO-Series from Schlage. And because CO-Series
locks offer a wide variety of options, it’s easy to find
the right solution for any facility. For openings with a
relatively small number of users, we recommend the
C0-100. It’s an offline keypad programmable lock. For
larger applications try the CO-200 or CO-250. They’re
computer programmable locks that can provide audit
trails. They also offer dual credential options
(card+PIN) that provide an even greater level of
security.
Compatible
The CO-Series was designed to easily integrate into
your facility. It can work in conjunction with Schlage and
Locknetics electronic locks and offers expanded cylinder, exit
device, and credential compatibility.
Class
CO-100
•Manually programmable • User rights stored on the lock
•Keypad only
CO-200 (shown)
•Computer or manually programmable
•User rights stored on the lock
CO-250
•Computer programmable• User rights stored on the card
Readers
•Keypad
•Magnetic stripe (swipe)
•Proximity
•Magnetic stripe plus keypad (swipe)
•Proximity plus keypad
Lever styles
Exit device compatibility
*
Rim
SVR
CVR/CVC
Mortise
Von Duprin 98/99 &
98/99 XP
4
4
4
4
Von Duprin 22/22F
4
4
Falcon 25
4
Sparta *See AD-Series Exit trim compatibility datasheet for complete list of compatability by
manufacturer.
Rhodes
Athens
Tubular
Chassis
Trim options
•Cylindrical
•Mortise
•Mortise deadbolt
Cylinder compatibility
•Exit Trim
Full size
Full size
FSIC
key-in-lever key-in-lever 6 & 7 pin
6 pin
7 pin
SFIC
6 & 7 pin
Schlage
l
l
l
Falcon
s
Sargent®
(10L + 11L full size)
s
s
s
Corbin Russwin®
s
s
Yale® (includes
Medeco 31*0100
FSIC)
s
s
•4 standard off the shelf (AA) batteries
Functions
Q
Best®
l =
with cylinder or less cylinder options
s =
less cylinder only
Q =
less cylinder, only with Sparta and Rhodes levers
Power
•Classroom/storeroom
•Privacy
•Office
Warm tone finishes
s
Note: See price book for specific configurations
605
606 612
643e
Bright brass
Satin brass
Satin bronze
Aged bronze
Cool tone finishes
Credential compatibility
The CO-Series is compatible with many different brands
and credential technologies.
For customers with an installed base of iButtons®, a combo
proximity keyfob with iButton option is available to make an easy
transition to proximity technology.
619 625 626626AM
Satin nickel
Bright
Satin chrome
Satin chrome
chrome
with antimicrobial
Reliable
When it comes to securing your facility, you can’t afford to take
chances. CO-Series locks are tested to the highest quality and
reliability standards in the industry, including:
•NSI/BHMA A156.25 & ANSI/BHMA Grade 1
•UL 294
•UL 10C
•ADA
Von Duprin 98/99 Series • 53
98/99 Strike/Stile information
Device type
Standard
single door
Strike
Trim/Stile
990/996
98/99
XP 98/99
98-F/99-F
XP98-F/XP99-F
Strike options / Dogging options
9875
9975
4 3/8"
(111mm)
Strike
Strike
w/mullion* Trim/Stile
299 x
4954
299F
909
Strike
Application
PL9827/PL9927
Pullman latch
299 (Top)
304L/248-L-4
(Bottom)
9827-F
9927-F
299 (Top)
304L (Bottom)
9847
9947
9848
9948
338 (Top)
385A (Bottom)
338 (Top)
385A (Bottom)
338 (Top)
385A (Bottom)
299F
499F x
9954
304L
4 7/8"
(124mm)
4 3/4"
(121mm)
Trim/Stile
—
—
—
—
—
—
—
—
—
—
576A-576B
4 3/4"
(121mm)
4 3/4"
(121mm)
—
—
576A-576B
4 3/4"
(121mm)
4 3/4"
(121mm)
1439 or
1410
3 13/16"
(97mm)
3 13/16"
(97mm)
299 x 5654
4 7/16"
(113mm)
4 1/4"
(108mm)
1408 x 5754
3 13/16"
(97mm)
3 13/16"
(97mm)
1606
3 15/16"
4 1/16"
4 3/8"
1606 x 1654
(103mm) (100mm)
(112mm)
4 1/4"
(108mm)
—
—
—
—
4 3/8"
(111mm)
—
—
—
4 1/2"
(114mm)
—
—
—
299 (Top)
299F (Middle)
304L (Bottom)
—
499F x 9854
—
KR9954
575-2
4 3/4"
(121mm)
3 13/16"
(97mm)
—
—
4 7/8"
(124mm)
3 13/16"
(97mm)
—
—
299 x
4954
1408 x 5754
4 1/4"
(108mm)
—
4 3/8"
(111mm)
4 1/4"
(108mm)
3 15/16"
4 1/16"
4 3/8"
1606 x 1654
(103mm) (100mm)
(112mm)
—
4 1/2"
(114mm)
4 7/16"
(113mm)
1606
575-2
9857
9957
299 x 5654
3 13/16"
(97mm)
4 3/4"
(121mm)
299 (Top)
299 (Middle)
304L/284-L
(Bottom)
4 3/4"
(121mm)
3 13/16"
(97mm)
990/996 696/697
1439 or
1410
4 3/4"
(121mm)
954 x
9954-XP
4 7/8"
(124mm)
4 3/4"
(121mm)
990/996 696/697
4 3/8"
(111mm)
575
299 (Top)
304L/248-L-4
(Bottom)
4 7/8"
(124mm)
696/697
Trim/stile
4 1/2"
(114mm)
4 3/4"
(121mm)
9827
9927
Latch retraction
Trim/Stile
990/996
499F x
9954
575
9847WDC
9947WDC
Strike
w/
mullion*
909 x
4954-XP
9875-F
9975-F
9847-F
9947-F
9848-F
9948-F
Optional
double door
909
4 3/4"
(121mm)
9857-F
9957-F
Optional
single door
696/697
299
4 1/2"
(114mm)
Standard
double door
Optional strike
—
—
—
Application Trim/Stile
990/996
696/697
Single door
3 11/16"
(94mm)
3 5/8"
(92mm)
990/996 696/697
Two vertical rod devices
3 11/16"
(94mm)
3 5/8"
(92mm)
Vertical rod with
Mortise lock device
4 3/4"
(121mm)
4 3/4"
(121mm)
Two vertical rods
4 1/4"
(108mm)
4 1/8"
(105mm)
Vertical rod with
Mortise lock device
4 3/4"
(121mm)
4 3/4"
(121mm)
Single door
4 1/4"
(108mm)
4 1/4"
(108mm)
Single door
Two vertical rod devices
4 1/4"
(108mm)
4 1/4"
(108mm) 304L
Two vertical 4 1/4"
4 1/4"
rod devices (108mm) (108mm)
Vertical rod with
Mortise lock device
4 3/4"
(121mm)
4 3/4"
(121mm)
Vertical rod
with
4 3/4"
Mortise lock (121mm)
device
260U (Top)
385A (Bottom)
260U (Stainless)
385A (Bottom)
304L (Bottom)
3 11/16"
(94mm)
3 5/8"
(92mm)
Two vertical 3 11/16"
rod devices (94mm)
3 5/8"
(92mm)
Vertical rod
with
4 3/4"
Mortise lock (121mm)
device
4 3/4"
(121mm)
Single door
4 1/8"
Two vertical 4 1/4"
(108mm) (105mm)
rods
304L (Bottom)
Vertical rod
with
4 3/4"
Mortise lock (121mm)
device
4 3/4"
(121mm)
4 1/4"
4 1/4"
(108mm) (108mm)
4 3/4"
(121mm)
9847WDC-F
9947WDC-F
338 (Top)
385A (Bottom)
Two vertical rod devices
4 1/4"
(108mm)
4 1/4"
304L
(108mm)
4 1/4"
Two vertical 4 1/4"
rod devices (108mm) (108mm)
9849
9949
9849
9949
249 (Top)
349 (Bottom)
Vertical cable with
Mortise lock device
4 3/4"
(121mm)
4 3/4"
(121mm)
Vertical
cable with
4 3/4"
Mortise lock (121mm)
device
Two vertical cables
4 1/4"
(108mm)
4 1/4"
(108mm)
Vertical cable with
Mortise lock device
4 3/4"
(121mm)
4 3/4"
(121mm)
Single door
4 1/4"
(108mm)
4 1/4"
(108mm)
Two vertical cable devices
4 1/4"
(108mm)
4 1/4"
(108mm) —
Two vertical
4 1/4"
4 1/4"
Cable
(108mm) (108mm)
devices
Vertical cable with
Mortise lock device
4 1/4"
(108mm)
4 1/4"
(108mm)
Vertical
cable with
4 3/4"
Mortise lock (121mm)
device
Two vertical cable devices
4 1/4"
(108mm)
4 1/4"
—
(108mm)
Two Vertical
4 1/4"
4 1/4"
Cable
(108mm) (108mm)
Devices
9849-F
9949-F
9849-F
9949-F
9849WDC
9949WDC
9849WDC-F
9949WDC-F
54• Von Duprin 98/99 Series
54
249 (Top)
349 (Bottom)
249 (Top)
349 (Bottom)
249 (Top)
349 (Bottom)
—
4 3/4"
(121mm)
4 1/8"
Two vertical 4 1/4"
(108mm) (105mm)
cable
—
Vertical
cable with
4 3/4"
Mortise lock (121mm)
device
Single door
4 3/4"
(121mm)
4 1/4"
4 1/4"
(108mm) (108mm)
4 3/4"
(121mm)
98/99 Strike information
Strikes for rim devices
264
299
299F
499F
1408
Projection 9/16" (14mm)
Projection 13/16" (21mm)
Projection 13/16" (21mm)
Projection 15/16" (24mm)
One per pair of doors
1439–Blade stop
1410–Integral stop
1606
1609
Projection 1/2" (13mm)
Projection 1/2" (13mm)
Projection 3/8" (10mm)
Panic devices only
– Requires coordinator
– For panic exit application only, not fire rated
Strikes for vertical cable devices
909
249 - Top249
strike
954
1"
(25 mm)
349
349 - Bottom strike
1¹⁹⁄₃₂"
(40 mm)
1¹⁄₂"
(38 mm)
2³⁄₄"
(70 mm)
Projection 13/16" (21mm)
⁹⁄₁₆"
(14 mm)
Projection 7/8" (22mm)
- For fire rated double door
applications
¹⁄₈"
(3 mm)
Projection 9/16" (14mm)
¹⁄₈"
(3 mm)
Projection 1/8" (3mm)
Strikes for vertical rod devices
248L-4
260U-Flush transom panic only
260U-F-Flush transom fire only
299
299F
Projection 3/8" (10mm)
Projection 3/8" (10mm)
Projection 13/16" (21mm)
Projection 13/16" (21mm)
304L
338
385A
283
Projection 13/16" (21mm)
Mortise 5/8" (16mm)
Mortise 2 1/2" (64mm)
For use with WDC devices
when used with wood frames
576A
576B
Strike options / Dogging options
XP Strikes for rim devices
Strikes for mortise rod devices
575
575-2
.
– Not for use with astragals
–For use on wood doors,
contact door manufacturer
–Acceptable for 90 minute
pair of hollow metal doors
55
Von Duprin 98/99 Series • 55
98/99 Dogging options
CD Cylinder dogging
SD Special center case dogging
Cylinder dogging is available on all 98/99™ Panic exit devices
to replace the standard hex key dogging. Unit requires a standard
1 3/4" (32mm) mortise cylinder with an inverted straight cam
(Schlage Cam B502-191 reference).
Special cylinder dogging in the center case is available for Chexit,
EL, QEL, ALK panic devices to allow for mechanical push/pull
operation. With this option, the latchbolt is held retracted and
pushbar is still operable. Specify handing—RHR or LHR.
To order, specify:
•Use prefix, CD, example CD99L
CDK Cylinder dogging kit*
For field conversion, a cylinder dogging conversion kit is
available.
Note: Available on Rim and Vertical Rod Panic Exit Devices only.
Order: 99CDK or 98CDK, specify finish.
To Order, Specify:
*Cannot be added to fire exit hardware.
•Use prefix SD, example SD99L and Handing
HDK Hex key dogging kit*
For field conversion, a hex key dogging conversion kit is available.
Strike options / Dogging options
SD requires 1 3/4" (32mm) mortise cylinder with an inverted
straight cam. (Schlage cam reference B502-191.)
•Not for 98/9975 Devices
Double cylinder
Double cylinder features an inside key cylinder which locks or
unlocks the outside trim and an outside key cylinder which
retracts the latch bolt only (Night latch function). Available on
rim or mortise lock device.
Order: 99HDK or 98HDK, specify finish.
*Cannot be added to fire exit hardware.
LD Less dogging
Less dogging is available in all 98/99™ Panic exit devices to
remove the dogging option.
To order, specify:
•Use prefix LD, example LD99L
Dog keys
Dog key (old style)
Dog key (standard)
2 3/16" (56mm)
2 3/4" (70mm)
Rim requires two rim type cylinders. Mortise device requires 1 rim
cylinder and 1 mortise cylinder 11/4" with a straight cam. (Schlage
cam reference B502-191.)
Available functions are thumbpiece, knob or lever.
To order, specify:
1. Suffix-2 with device/trim number, example 99TP-2.
/32" (6mm) hex
7
5
/32" (4mm) hex
2. Handing required, LHR or RHR.
-2SI Double cylinder with security indicator
The Von Duprin Classroom Security Indicator provides an at-aglance verification of the locked/unlocked status of the door
from inside of the room. This option can be ordered as a new
product or as a retrofit conversion kit to an existing 98/99 device.
Indicator in Unlocked state presents a 1/2" x 1/2" metal flag (white
background with black icon) at top of device head. Indicator in
Locked state has no flag present.
To order, specify:
1. S
uffix-2SI with device/trim number, example
99L-2SI.
2. Handing required, LHR or RHR.
56• Von Duprin 98/99 Series
56
98/99 Electrical options
RX Request to exit
The RX (2xit) feature is used to signal the use of an opening.
This device is equipped with one internal SPDT switch which
monitors the pushpad.
The device can be connected to a security console, or may be
used as a single door alarm when used with a horn and power
supply.
The RX switch option should not be used to control a load, but
as a signalling switch (0.5 amps. resisitive maximum).
The RX switch is available in a low current (LC) switch. Most
commonly used in computer operated monitoring systems.
To order, specify:
•
•
Standard – use prefix RX, example RX99EO
Low Current – use prefix RX-LC, example RX-LC98EO
RX2 Double request to exit
The RX2 feature uses two RX switches.
•
Standard – Use prefix RX2, example RX299EO
WP-RX Waterproof request to exit
LX Latchbolt monitoring
Monitors pushpad and latch bolt
The SS feature is used to signal the unauthorized use of an
opening. This device is equipped with two internal SPDT
switches. One switch monitors both the pushpad and the latch
bolt assembly, making the latch bolt tamper resistant, for
positive security. An additional SPDT switch is connected to the
1 1/4" (32mm) mortise cylinder with straight cam for alarm
“bypass.” (Schlage cam reference B502-191). The device can be
connected to a security console, or may be used as a single door
alarm when used with a horn and power supply.
Pushpad reads: “Emergency Exit ONLY – Push To Open And
Sound Alarm.” Pushpad is only available in US32D finish with red
silk-screened lettering.
The SS mortise lock device is furnished with both the signal
switch device and the SS7500 mortise lock. The SS7500 mortise
lock has the versatility and advantages of the 7500 lock with the
addition of signalling functions to monitor latch bolt operation
and the trim locking function. The SS7500 mortise lock is
supplied standard with the SS mortise lock device.
To order, specify:
1. Prefix SS, example SS99L.
2. Handing required, LHR or RHR.
Electrical ratings:
Up to 2.0 AMPS @ 24VDC
The LX feature is used to signal the use of an opening. This
device is equipped with one internal SPDT switch which
monitors the latch bolt.
The device can be connected to a security console, or may be
used as a single door alarm when used with a horn and power
supply.
The LX switch option should not be used to control a load, but
as a signalling switch (0.5 amps. resistive maximum).
Popular SS application
Unauthorized use of this opening will activate the local horn. The
key switch permits inhibiting this ­system for authorized entry.
Electrical options & accessories
To order, specify:
SS Signal switch
The LX switch is available in a low current (LC) switch. Most
commonly used in computer operated monitoring systems.
To order, specify:
•
Standard – Use prefix LX, example LX99EO
•Low Current – Use prefix LX-LC, example LX-LC98EO
Electrical rating for all switches:
•
Standard – 2 Amp maximum @ 24VDC
•
Low Current (LC) - below 50 Milliamps @ 24VDC
Note: All switches can be either factory or field installed
57
Von Duprin 98/99 Series • 57
98/99 Electrical options
CX The Chexit®
Internal horn: Whenever the device is in alarm or the push pad is
pressed the internal horn will sound. The volume level of this
horn exceeds 85 db at 6 feet.
Door position input: An external door position switch can be
connected to the Chexit.
Designed for use on delayed exit applications, the Chexit ­system is
ideal for controlled areas.
All controls, auxiliary locking, local alarm, and remote signalling are
self-contained in the Chexit, providing safe, secure, easy to install
and simple to operate door control and exit hardware.
Chexit controlled exit device for use on panic or fire exit hardware
applications.
This concept in delayed exit systems combines life safety with the
needs of security and meets all requirements of NFPA 101 for
“special locking arrangement.”
Electrical options & accessories
The Chexit device includes a 6" x 20" decal for application on door.
“PUSH UNTIL ALARM SOUNDS.
DOOR CAN BE OPENED IN 15 SECONDS”
Minimum width door opening:
•3' Device 34" opening
•4' Device 40" opening
Consult factory for other size requirements.
Power supply requirements
Solenoid specifications:
•Continuous duty – 24VDC
•Current inrush – 16 amperes
•Current holding – .3 amperes
Requires PS914 Power Supply
Request to exit switch: Built into the device to detect when
someone attempts to exit. Pushing the push pad when the device
is armed will cause this switch to start an irreversible alarm cycle.
Nuisance alarm: When a Chexit is located in a public area, it can be
desireable to limit false alarms. If the Nuisance Delay options are
set to off, the device will go into alarm as soon as the push pad is
touched (when armed). Turning the Nuisance Delay on will require
the push pad to be pressed for 1 second before the Chexit goes into
alarm. If the Nuisance Audible and Nuisance Delay are both on, the
alarm will sound as soon as the push pad is pressed, but the alarm
sequence will stop unless the push pad is held for 1 second or more.
Remote alarm: A relay contact is provided to give external alarm
indication. This contact close when the device is in an irreversible
alarm condition. This contact can be used to drive a horn, lamp, or
other indicative device.
Key switch: The Key switch provides the means to arm, disarm or
reset the Chexit. The key can be removed in either the Arm or
Disarm position.
Indicator lamp: The status of the Chexit can be determined by the
indicator lamp. When the lamp is off, this indicates the device is
disarmed and is functioning as a normal exit device (no delay). A
continuously on lamp indicates the device has just been armed and
as soon as the selectable rearm timer expires, the device will arm.
A slow flashing lamp indicates the device is armed. A fast flashing
indicator lamp indicates the device is in alarm.
58• Von Duprin 98/99 Series
58
Using the door position input ensures that the door is in the
closed and latched position before the device rearms.
External inhibit input: This optional input is provided to allow
authorized egress of the Chexit in the armed condition. It also
allows remote reset of the Chexit in an alarmed condition.
Fire alarm input: This input disables the Chexit immediately
upon a fire alarm.
Internal auxiliary lock: The Auxiliary Lock is engaged when the
Chexit is armed. The locking mechanism is specifically designed
to hold securely even when the exit device is struck with forceful
blows.
User defineable rearm time: The Rearm time is the amount of
time after the device is activated before it arms. It is designed to
give someone time to pass through the door before rearming
oocurs. Timing can be changed by the user for any time between
2 and 28 seconds in two second increments. There is also an
infinite rearm setting that requires the use of an external door
position switch. In this setting the door remains in the rearm
mode until the door is closed. This can be useful on jet way doors
in an airport.
Factory defineable delay time: Most jurisdictions allow 15
seconds of delay before allowing egress. In those cases where 15
seconds is not appropriate, Von Duprin can set the Chexit for any
delay time between 0 and 60 seconds on 2 second increments.
For delays greater than 15 seconds a letter from the local
authority is required.
98/99 Electrical options
Chexit typical application
Chexit single door with options – The Chexit is used as an access
control device. The card reader allows access. Also shown in this
application is an external horn and door position switch. The
auxiliary horn is used for increased volume in remote locations.
Using a door position switch gives added security to the opening
in case the door is not reclosed.
With the Chexit disarmed, the opening functions as a normal exit
device. If card readers are required on both sides of the door, the
normally closed contacts of the readers should be weird in series.
120 VAC 3 x 14 ga.
2 x 12 ga.
Power Supply
To Fire Alarm 2 x 18 ga.
2 x 18 ga.
2 x 18 ga.
2 x 12 ga.
6 x 18 ga.
Horn
2 x 18 ga.
(new)
EPT
KPT-10
Chexit
Gnd
+24
PS914
Power Supply
+24
Red
Gnd
Black
SC
White
FA
Yellow
DPS
Orange
Fire Alarm
Door Position
Switch
Card Reader
+
–
III
Green
CM+
Gray
CM-
Violet
NO
Blue
C
For Hardware Applications
The assembly includes both a 24VDC Input and External Inhibit
standard. The External Inhibit provides remote arming and
dis-arming.
The key switch uses a standard 1 1/4" (32mm) mortise cylinder
with a straight cam (Schlage 20-001, B502-191 cam). The unit
operates on one standard 9-volt alkaline battery. When the
battery is weak, the horn will emit an intermittent low battery
alert signal.
The alarm can automaticaly re-arm with a 1 1/2, 3 or 6 minute time
delay upon request.
Alarm kits are available with a choice of two switch kits, RX or
LX. RX monitors the touchpad and is furnished standard. LX
optional latch bolt monitoring is recommended for use with
surface vertical rod exit devices or when alarm needs to sound
from both the exit device and trim side of the door. Specify
ALK-LX.
Brown
Chexit
Cable
Note: For latch bolt monitoring on a 98/9975 with ALK, specify a SS7500 lock. LX switch
not available for 98/9975 devices.
Horn
The ALK is available in two styles, 99ALK, grooved cover and
98ALK, smooth cover.
Door width reference for CX devices
Device
ALK Alarm kit is a simple yet effective way to deter unauthorized
use of an opening. While the exit device is still a means of egress,
the ALK kit contains an internal horn. When the touch bar is
depressed, the horn sounds to provide an audible means of
signaling that the opening has been violated. The alarm kit can
be armed or disarmed by key thus allowing the exit device to be
set in an armed or disarmed mode. The horn is rated at 85
decibels.
3' (914mm)
Length
4' (1219mm)
Length
The ALK includes a 6" x 20" decal for application on door
“EMERGENCY EXIT ONLY. ALARM WILL SOUND. ”SS push bar
trim can be used instead of the door decal, specify SS push bar
trim when ordering the device.
CX98/98-F/99/99-F
2'10 1/2" (864mm)
3'4 1/2" (1016mm)
CX9875/9875-F/9975/9975-F
2'10" (864mm)
3'4" (1016mm)
CX9827/9827-F/9927/9927-F
2'10" (864mm)
3'4" (1016mm)
CX9857/9857-F/9957/9957-F
2'10" (864mm)
3'4" (1016mm)
CX9847/9847-F/9947/9947-F
2'10" (864mm)
3'4" (1016mm)
CX9848/9848-F/9948/9948-F
2'10" (864mm)
3'4" (1016mm)
CX9849/9849-F/9949/9949-F
2'10" (864mm)
3'4" (1016mm)
CX9849/9849-F/9949/9949-F
2'10" (864mm)
3'4" (1016mm)
To Order, Specify:
CX-R 98/9927
2'4" (838mm)
2'10" (1041mm)
1. Standard, 98 ALK
CX-R 98/9947
2'4" (838mm)
2'10" (1041mm)
2. Cylinder Dogging, CD98 ALK
CX-R 98/9947-F
2'5" (864mm)
2'11" (1016mm)
3. Special center case dogging, SD98 ALK
CX-R 98/9947WDC
2'5" (864mm)
2'11" (1016mm)
4. If AR desired, specify AR 1.5, 3 or 6
CX-R 98/9975
2'5" (864mm)
2'11" (1016mm)
Electrical options & accessories
Chexit mortise lock device
the outside trim works
independently from the
Chexit device.
Cable
Card
Reader
(Inside or
Outside)
Note: Chexit rim or vertical
rod/cable devices lock any
outside trim input when the
device is in the armed
condition. If access is
needed from the trim side
of the door, some type of
electric switch would need
to be tied into the external
inhibit input of the device.
ALK Alarm kit
When the ALK is used, standard dogging is removed. If cylinder
dogging is required there are two choices. Special center case
dogging is available or for 3' or 4' doors. The ALK can be moved
to the hinge side of the device and standard cylinder dogging can
be added.
Minimum door opening sizes on ALK applications
Device
3' (914mm)
Length
4' (1219mm)
Length
98/98-F/99/99-F
2'10" (864mm)
3'4" (1016mm)
9875/9875-F/9975/9975-F
2'10" (864mm)
3'4" (1016mm)
9827/9827-F/9927/9927-F
2'10" (864mm)
3'4" (1016mm)
9857/9857-F/9957/9957-F
2'10" (864mm)
3'4" (1016mm)
9847/9847-F/9947/9947-F
2'9" (838mm)
3'3" (991mm)
9848/9848-F/9948/9948-F
2'9" (838mm)
3'3" (991mm)
59
Von Duprin 98/99 Series • 59
98/99 Electrical options
E Electric mortise lock device
Electrical options & accessories
The electric mortise lock device has all the versatility and
advantages of the standard mortise lock device, plus the
advantage of being electrically controlled by a remote switching
device, an access control system or an automatic fire alarm
system. The device features the E7500 mortise lock. The E7500
controls the locking of the outside trim. When unlocked, the door
remains latched, preserving the fire rating of the door and making
it particularly useful where codes permit locking but require
unlocking during a fire emergency. The outside trim cylinder
retracts the latch bolt for mechanical override, night latch
function. Only available with TP, K or L functions.
The E7500 lock contains a SPDT signal to monitor the outside
trim condition (locked or unlocked) and a second SPDT signal
switch to monitor the latch bolt.
Standard features:
•
Field reversible handing
•
24 VDC continuous duty solenoid
Optional features:
•Fail safe (locked when energized, unlocked when deenergized or during power failure). Specify with suffix “FS.”
•Fail secure (unlocked when energized, locked when deenergized or during power failure). Specify with suffix “FSE”
•24 VAC (with SO option)
•12 VDC
•12 VAC (with SO option)
Note: Some Fire codes will require “Fail Safe” (FS) operation for stairwell doors.Be sure to
specify the correct operation for your application.
Electrical specifications:
•Solenoid — .60 AMPS @ 12VDC
.30 AMPS @ 24VDC
•Each switch — Up to 2.0 AMPS @ 24VDC Maximum
The E option does not include the power transfer from door to
frame, the power supply or the control operator. (Refer to EPT-10
and PS902 or PS914 power supply)
To order, specify:
1. Use prefix “E,” example E9975.
2. FS or FSE
3. Voltage and current.
Allegion Connect
Allegion’s cross-category Connect features common interconnect
components to our electrified options. Allegion Connect is a quick
and easy way to connect power sources; all the way from your
power supply to locking device. There is no wire cutting; reducing
installation and maintenance time ultimately cutting cost. After
installation, Allegion’s Connect continues to provide benefits
throughout the lifetime of the opening by offering a service kit
for repairs or modifications in the future.
Features and benefits
•
Quick: common connections reducing installation time
•Perfect Connections: these factory installed connectors
ensure the right wires match up every time
•Protective: the connectors protect the connection points
throughout the installation process and lifetime of the opening
•Interchangeable: all Allegion Connect products utilize the
same connectors
•Maintenance: you no longer need to cut away wire to
disconnect Allegion products, also available is a service kit
specifically for Connect products.
Harness length
6 Inches
12 Inches
26 Inches
32 Inches
38 Inches
44 Inches
50 Inches
192 Inches
Connectors
on both ends
CON-6
CON-12
CON-26
CON-32
CON-38
CON-44
CON-50
CON-192
Connectors on one end,
crimped pins on the other end
CON-6P
CON-12P
CON-26P
CON-32P
CON-38P
CON-44P
CON-50P
CON-192P
Power Supply Wire Harness = Connectors on one end, stripped leads on the other end,
offering a direct connection to the power supply
6 Inches
CON-6W - wire extension to power supply
Consult door manufacturer for harness length requirements.
Note: You will need to purchase a separate wiring harness to go from exit device to hinge/
EPT and an additional harness to go from hinge/EPT to power supply or access control
system. Harness part numbers with ordering information can be located in the Schlage,
Von Duprin and Falcon pricebooks. A service kit is available for order in the Schlage, Von
Duprin and Falcon pricebooks. Included in this kit are male end plugs, female end plugs
and pins to customize harnesses to your application.
Note: Must be ordered with exit devices and locks
How to order
1.Specify CON for Connect electronic options
Example: EL-99-EO-CON (99 Series Electrified Latching exit only
with Connect connectors)
2.Specify harness length; Consult door manufacturer for harness length
Electric mortise lock device
Adaptable for openings where ­continuous latching is required
while the trim may be electrically locked or unlocked from a
remote location—stairwells, exterior doors, etc.
Minimum system requirements:
•PS902
•EPT-10
60 • Von Duprin 98/99 Series
60
3.Specify Von Duprin EPT10-CON or Ives 7200 power transfer hinge
Wire run options
98/99 Electrical options
EL Electric latch retraction
QEL Quiet electric latch retraction
If manual hex-key dogging is required, specify HD-EL. If cylinder
dogging is required, the standard cylinder dogging is not
available, but special center case dogging is available, specify
SD-EL. SD-EL is not available on the 9875 or 9975 devices.
If cylinder dogging is required, the standard cylinder dogging is
not available, but special center case dogging is available,
specify
The EL feature allows for the remote unlatching of exit devices. A
control station operator can flip a switch to retract the latch bolt
and immediately change an exit door to push-pull operation. A
powerful, continuous duty solenoid retracts the latch bolt, either
for momentary unlatching, or for extended periods of time. The
EL feature is an alternative to manual dogging.
EL devices are also useful with automatic door operators, and
may be applied to fire-rated applications when under the control
of an automatic fire alarm system.
UL approved for Class II circuit applications.
The EL option does not include the power transfer from door to
frame, the power supply, or the control operator. Refer to EPT-2
power transfer and the PS914 power supply.
Solenoid specifications:
Continuous duty – 24 VDC
Current inrush – 16 Amps
Current holding – 0.3 Amps
Solenoid resistance:
-grn-yel 1.2 – 2.2 OHMS
-grn-org 100 – 150 OHMS
PS872 Wiring
To order, specify:
Standard – use prefix EL, example EL99L.
Hex Key dogging – Use prefix HD-EL, example HD-EL99L
special center case dogging – Use prefix SD-EL, example
SD-EL99L
Popular EL application
Power supply PS914-2RS
Electric power transfer EPT-2 or EPT-10
SD-QEL. SD-QEL is not available on the 9875 or 9975 devices.
QEL devices are also useful with automatic door operators, and
may be applied to fire-rated applications when under the control
of an automatic fire alarm system.
UL approved for Class II circuit applications.
The QEL option does not include the power transfer from door to
frame, the power supply, or the control operator. Refer to EPT-2
power transfer and the PS902 or 914 power supply.
The PS902/914 with the 2RS, 4RL or 4R board is the minimum
required. Other option boards available for other functions, see
PS902/914 power supply for additional information.
QEL Electrical load
Voltage
24VDC
Current
1.4 A Inrush (0.5 sec.)
0.14 A Holding
2.0 A Calibrate (3 sec. one time)
PS872 Wiring
To order, specify:
Standard — use prefix QEL, example QEL99L.
Special center case dogging — use prefix SD-QEL,
example SD-QEL99L
Popular application
Power supply PS902-2RS
Electric power transfer EPT-2 or EPT-10
120/240
VAC
SC I1 O1 I2 O2 GND
EPT-2
120/240
VAC
EL #2
a*
SC I1 O1 I2 O2 GND
Input #2
(Required for
independent
operation only).
b*
EPT-2
QEL #2
a*
EPT-2
Von Duprin
exit device
a*
b
*
All other 98/99EL
device types
Control Switch
(Required for
independent
operation only).
EPT-2
QEL #1
Input #1
a*
b*
EL 98/99 Rim
Input #2
b*
EL #1
a*
Electrical options & accessories
The PS914 with the 9002RS option card is the minimum option
card required. Other option cards available for other functions,
see PS914 power supply for additional information.
The QEL feature allows for the remote unlatching of exit devices.
A control station operator can flip a switch to retract the latch
bolt and immediately change an exit door to push-pull operation.
Different than the popular EL, the QEL quiet operation is
achieved using an electric drive motor which retracts the latch
bolt either momentary unlatching or for extended periods of
time. This feature is an alternative to manual dogging.
EL Wire
length (feet)1
Wire gauge
(AWG)
0-500
12
0-300
14
0-200
0-250
16
12
0-150
14
0-100
16
0-1200
18
1. Wire lengths include an EPT, Door loop, electric hinge or pivot and are
measured one way between the PS914/option board and the device.
2. Table is applicable to devices that have shipped after August 2012.
Input #1
b*
a*
b*
Distance (one-way)
200´
Wire gauge
18 AWG
320´
16 AWG
500´
14 AWG
800´
12 AWG
Wire selection
1200 ft. Max.
Switch wire size
18 gauge standard
61
Von Duprin 98/99 Series • 61
98/99 Electrical options
Power Supplies
Series PS902/914
PS902 PS904 PS906 PS914
Number of connectors on
power supply for the
following:
2 amps 4 amps 6 amps 4 amps
Distribution boards
1
2
3
2
Battery back-up board
1
1
1
1
Note: One fire alarm board can be connected directly to the PS902. If a fire alarm board is
desired for the PS904, PS906 or PS914 it can be connected to
a distribution board.
Electrical options & accessories
Overview:
The PS900 Series is a consolidated line of power supplies and
accessories that offer enhanced flexibility and functionality
specific to the changing needs of the access control market. The
PS900 Series can be used in a variety of applications to convert
high voltage AC power into the low voltage DC outputs required
by most access control devices. The PS900 Series protects
devices downstream by providing Class 2*, filtered and regulated
power. The full line is UL294 certified.
Note: PS906 can provide Class 2 rated outputs when used with 900-8P distribution
board.
Features:
•Constant output rating at both 12 VDC and 24 VDC provides
superior performance ; includes field selectable jumper
•Polarized connectors for option boards eliminate need for
racks and side connectors
•Flat mounting of option boards provides easier access to
terminal blocks for connection of electrified devices
•High voltage protective cover
•Battery back-up board auto-selects voltage
•Fire alarm relay can be configured to provide either switched
or un-switched outputs from a power supply
•PS914 designed with high in rush current for powering
electrified panic devices
Applications:
The PS900 Series of power supplies works with many electrified
devices including Schlage electromagnetic locks, Schlage
AD-Series hardwired locks, Schlage electrified mechanical locks,
Von Duprin electrified strikes , Von Duprin exit devices, and many
other brands.
Accessories:
The Schlage PS900 Series features seven option boards for use
in a variety of applications. All Schlage PS900 Series power
supplies option boards are UL 294 certified.
Option boards:
900-4R: 4 relay controlled output board to power multiple
devices
900-4RL: 4 relay distribution board with logic is field
configurable for time delay function, auto operator, security
interlock
900-8F: Provides 8 individually fuse-protected outputs, giving
the flexibility to power multiple devices and provide another layer
of protection
900-FA: Emergency interface relay integrates with fire alarm and
is used to cut power in case of emergency
900-BB: Battery backup
•Universal 120-240 VAC input
900-2RS: 2 relay EL panic device control board (PS914 only)
•Low voltage DC, regulated and filtered
900-BBK: Battery backup kit includes two 7A/hr batteries and
provides up to four hours of backup power when cycled every 5
minutes at full load
•Electronic power limiting foldback circuit for AC current
overload protection
•Fused primary input
•AC status monitor- isolated SPDT contacts
•AC input and DC output LED status indicators
•Cover mounted AC input indication
•Hinged cover with lock down screws
Certifications:
•UL 294 certified—the standard for access control
•Class 2 rated*
* Except PS906, output rating exceeds Class 2 power limits
Once power is converted to low voltage DC, the PS900 Series
offers a variety of distribution options, including basic fuse
protection, simple relay, and advanced logic providing complex
sequencing and timing functions.
* PS906 can provide Class 2 rated outputs when used with 900-8P distribution board.
62• Von Duprin 98/99 Series
62
98/99 Electrical options
EPT Electrical power transfer
PNT Pneumatic transfer
Electric Power Transfer provides a means
of transferring electrical power from a
door frame to the edge of a swinging
door. The units are completely concealed
when the door is in the closed position,
and are ideal for installations involving
abuse or heavy traffic.
Two models are available; EPT-2, two 18
gauge wires and EPT-10, ten 24 gauge wires. The EPT-2 and
EPT-10 are U/L listed as “miscellaneous door accessory”.
UL Listed for use on firedoors
Door applications:
up to 5" butt hinges – 180˚ swing,
5 1/2" butt hinges – 130˚ swing,
6" butt hinges – 110˚ swing,
/4" butt offset pivots 180˚ swing.
3
Finishes
SP28 (sprayed aluminum)
SP313 (sprayed duranodic).
Dimensions
Housing
9" x 1¹|₄" x 1⁵|₈" (229mm x 32mm x 38mm)
EPT-2
Two 18 gauge wires, Up to 2 AMPS @ 24VDC, with
a 16 AMPS Maximum Surge
EPT-10
Ten 24 gauge wires, Up to 1 AMPS @ 24VDC, with a
16 AMPS Maximum Surge
PNT-1
⁵|₃₂" Tubing
To order, specify:
1. EPT-2 ,EPT-10 or PNT-1.
2. Finish, SP28 or SP313.
Electrical options & accessories
Not for use with swing clear hinges or center-hung pivots.
E996L Electrified breakaway lever
E996L electrified lever trim provides
remote locking and unlocking. Furnished
standard in fail safe (FS) condition, can be
field converted to fail secure (FSE) where
allowed. E996L is furnished standard with
cylinder operation for nightlatch (NL)
function, or with blank escutcheon (BE).
63
Von Duprin 98/99 Series • 63
98/99 Mechanical options
AX Accessible device
The AX device is a UL certified exit device designed to meet the
progressive requirements of the California Building Code for
accessible openings. This device meets the 5 lbs of operating
force requirement called for in chapter 11B-309.4. The AX device
also exceeds ANSI/BHMA requirements. Available devices
include: AX98/99, AX98/99-F, AX98/9949LBL, AX98/9949-F
LBL, AX98/9949-F LBLAFL. Additionally, all AX devices will be
shipped with a new UL label clearly stating “Meets California
building Code (2013) Sec. 11B-309.4” and an “AX” identifier label
on device center case. See images below for reference.
WS Surface vertical rod one-point
and three-point exit devices
WS Multi-point exit devices for tornado application devices
WS98/9927 (one- point) and WS98/9957 (three-point) surface
vertical rod exit devices are designed, tested and certified to
comply with the Federal Emergency Management Agency's
publication FEMA 361- Design and Construction Guidance for
Community Safe Rooms.
UL Listing – panic hardware UL 305; and fire exit hardware UL 10C:
WS98/9927:
3 hour pairs of doors double egress, 90 minutes
swinging same direction, 8'0" x 8'0" BHMA Grade 1,
ANSI A156.3-2001
Mechanical options & accessories
WS98/9957:
3 hours single doors, 4'0" x 8'0" BHMA Grade 1,
ANSI A156.3-2001
Windstorm ratings:
WS98/9927:
Miami-Dade County/FBC compliance to TAS 201, TAS 202, TAS 203; design load rating +150/-150 PSF
(245 MPH wind zone); Enhanced Hurricane Protection
(EHPA) ASTM E1996, ANSI/ICC 500 (245 MPH wind
zone).
XP Extra performance
For increased security the
XP98/99 Rim exit device has
a static load force resistance
of more than 2,000 pounds,
twice that of standard rim exit
devices. The two-piece latch
bolt forms a 90° latch-tostrike contact. The “smart” latch changes shape when subjected
to external forces. This design enables the exit door to withstand
an external attack and remain secure. Additionally, the patented
latch bolt design provides a greater, longer-lasting latch bolt to
strike contact which is not easily affected by the twisting motion
of a weakened frame, resulting in an opening that will remain
strong.
With a door loaded to 250 pounds, XP98/99 requires less than
40 pounds of pressure to open, 25% less than the safety code
requires.
XP98/99 is available for panic or fire exit hardware applications.
Dimensions, finishes and trim options are equal to the standard
98/99 series rim exit device.
Note: The 909 strike is to be used for all applications.
The exception occurs with the use of fire rated double door applications, in this instance
the 954 strike is required.
UL-FEMA 361 certified 8'0" x 8'0" pairs, swinging same direction and 4'0" x 8'0" single non-fire rated flush hollow metal. UL-ANSI/ICC 500 certified for F5 tornado
applications.
WS98/9957:
UL-FEMA 361 certified 4'0" x 8'0" single flush hollow
metal (fire-rated and panic). UL-ANSI/ICC 500 certified
for F5 tornado applications.
These devices are listed with Steelcraft Paladin™ PW-Series doors
for tornados, and Steelcraft H-Series doors hurricane applications.
To order, specify: WS prefix, example WS9927-F
LBR Less bottom rod, panic and fire rated
LBR option is available, using a spring loaded auxiliary latch bolt
installed in the lower door edge. When exposed to heat the
auxiliary latch bolt releases, keeping the doors in alignment and
closed during a fire. UL listed 3 hours on hollow metal doors double
egress, 90 minute swinging same direction, and 20 minutes wood
doors (consult wood door manufacturer). Fits door stiles as narrow
as 3 5/8".
LBR devices must be ordered in pairs or must be used in
conjunction with an approved automatic or constant latching
flush bolt.
PL Pullman latch
When PL is specified the standard latches are replaced with
pullman style latches. Pullman latches are always extended and
are most commonly used in conjunction with electric strikes and
LBR-less bottom rod application. Not available with Fire rated
devices.
Not recommended where security is of the utmost importance since latches do not
deadlock.
64 • Von Duprin 98/99 Series
64
98/99 Mechanical options
Dummy pushpad
The 330 dummy pushpad is designed as a companion unit for all
99 devices. The 350 dummy pushpad is a companion unit for all
98 devices. The pushpad is rigid or nonfunctioning. A push/pull
operation can be accomplished by using 990DT, 996DT trim or
any Ives Pull.
The 330/350 can be equipped with a functional pushpad and
will accommodate an RX or WP-RX switch. Specify RX-330.
May also be equipped with the RX2, double RX switch. Specify
RX2-330
To order, specify:
1. 330 or 350.
RSS Red Silk Screen
Red silkscreen lettering on touchpad trim. - "Emergency Exit
Only, Push To Open And Sound Alarm". This comes standard on
SS devices.
To order, specify: Suffix RSS, 9927L-RSS RHR
2. Size 3' or 4' (914mm or 1219mm)
3.Finish, US3, US4, US10, US26, US26D, US28, 313 & 315.
US32D – 350 only.
4. Specifiy RX, WP-RX or RX-2 if desired.
SG Safety glow
To order, specify: Suffix SG, EL 9927L-SG
Braille, embossed and knurled touchpads
* Image shown is a special order.
Mechanical options & accessories
Self-illuminating touchpad defines the location of the exit door
in dark or smoke-filled area. The safety glow coating is a special
powder coat finish that glows brightly during low or no light
conditions. This coating was developed to meet MEA standards
where luminescent exit door markings are required in
commercial facilities. There are no batteries or electronics, the
coating is charged when exposed to light.
Braille touchpad embossed with the standard message
“CAUTION ­STAIRWELL” in braille and raised letters provides
assistance to persons with impaired vision. Letters are 1/2"
(13mm) high and braille is #2, raised height is 3/32" (2mm). Other
messages are available on special order, limited to 20 ­characters
per line.* To order, specify: Suffix BR, EL9927L-BR
Embossed touchpad is embossed with the word “PUSH”.
To order, specify: Suffix EMB, EL9927L-EMB
Knurled touchpad is to provide warning to persons with impaired
vision. To order, specify: Suffix PBKN, EL9927L-PBKN
Consult factory for availability.
65
Von Duprin 98/99 Series • 65
98/99 Mechanical options
PN Pneumatic controlled exit devices
Mechanical options & accessories
The PN feature provides remote latch bolt ­retraction in
hazardous areas where electrically operated devices would not
be permitted. The pneumatic solenoid will retract the latch bolt
for momentary or prolonged periods. PN exit devices are
particularly suited for use with automatic door operators. The PN
feature is available on both Panic and fire exit hardware devices.
The PN feature includes a special actuating linkage that gives
building owners the option of mechanically or pneumatically
dogging the exit device. If manual hex-key dogging is required,
specify HD-PN (Dogging the device, whether mechanically or
pneumatically, makes the device function as a push/pull unit and
reduces the wear on its moving parts.) If cylinder dogging is
required, the standard cylinder dogging is not available, but
special center case dogging is available, specify SD-PN. SD-PN is
not available on the 9875 or 9975 devices.
When activated pneumatically, the latch bolt(s) of the exit
device retract in 1/2₂ to 11/2 seconds. This pneumatic operation
uses air pressure ranging from 50 to 100 pounds per square inch.
This product will function only when it is part of a pneumatic
system (air compressor, air lines, pneumatic system, etc.).
Contact LCN for correct control boxes.
To order, specify:
•Standard — Use prefix PN, example PN99NL
•Hex Key Dogging — Use prefix HD-PN, example HD-PN99NL
•Special Center Case Dogging (handing is required, specify
RHR or LHR) — Use prefix SD-PN, example SD-PN99NL
PNT pneumatic transfer
Pneumatic controls
PNT-1 is available for pneumatic latch retraction exit devices.
Appearance and dimensions are identical to EPT models.
66 • Von Duprin 98/99 Series
66
98/99 Device options & accessories
RG-27 Vertical rod and latch guard
Series RG-27 Vertical rod and latch guards protect the
bottom rods of exit devices from the damaging
impacts of carts or gurneys passing through doors. (If
bottom rods become damaged, the exit device will
not function as intended and can jeopardize the
ability to exit safely during an emergency.)
36"
In addition to protecting the vertical rod, the guard
provides a smooth, unobstructed surface so the door
can be pushed open easily with the bumpers of a
wheelchair. The latch guard portion is 10" high. The
standard latch guard features a 45° ramp. The
extended latch guard offers a continuous ramp in 3'
or 4' widths.
All stainless steel construction in US32D finish.
Latch guards can cover latches as large as
1 1/4"W x 10"H x 1 7/8" projection.
997 Cover plate kit
For 98/99 rim device, kit
contains inside and outside
plates for hinge stile cutouts,
an inside plate for the lock stile,
and necessary screws. Plates
are designed to cover cutouts
required by most existing exit
device installations.
Specify finish.
13/4" (44mm)
9"
(229mm)
WDA Cover plate kit
For wood door applications, used to cover up
door preparations for control, also prevents the
control from boring into the wood door. Finished
to match control.
#10WDA Cover plate kit for 370
series controls
Extended latch guard
Latch guard
7 7/8"
7 7/8"
10"
12"
3' or 4'
4 3/8"
#33A-WDA Cover plate kit for 360
series controls
2 1/4"
2 1/16"
2 1/16"
Models
RGO
Rod guard only (projection 1 3/16")
RG-27
Rod and latch guard
RG-27-3 3' (914mm) Rod guard and extended latch guard
RG-27-4 4' (1219mm) Rod guard and extended latch guard
LGO
Latch guard only
LGO-3
3' (914mm) Extended latch guard only
LGO-4
4' (1219mm) Extended latch guard only
When using on wood fire doors, high density block is required.
To order, specify:
1. Model number.
2. Handing (except on RGO).
GBK Glass bead kit
Glass bead conversion kits are available for all 98/99™ Series
devices for use on doors with raised glass beads. Each kit
consists of 1/4" (6mm) shim sets. GBK for surface vertical rod
ships with 1/8" shims for rod guides.
Device options & accessories
Rod guard
To order, specify:
1.99GBK
2.Device type (rim, mortise, surface vertical rod, concealed
vertical rod)
3. Wood door, when used with concealed vertical Rod
4. W
hen used with 330/350 Dummy pusher, order two hinge
stile shims.
3. Door material if other than hollow metal.
4. Optional sex bolt mounting available.
67
Von Duprin 98/99 Series • 67
98/99 Device options & accessories
Cylinders
Cylinders are not furnished with device or trim and must be specified when ordering. Refer to trim pages for cylinder type.
Device options & accessories
Mortise — 3215 (Schlage 20-001, B502-191 cam)
Dogged (inverted) cam
Undogged cam (standard operations)
For cylinder dogging
or 360L
For standard trim functions
or 360L-NL
68 • Von Duprin 98/99 Series
68
Rim — 3216 (Schlage 20-022 cam)
98/99 Device options & accessories
Mullions
Removable steel mullions provide single door
performance in double door openings with rim devices.
Mullions are easily removed by loosening bottom set screw
and removing top fitting cover. The top mullion fitting is
attached to the frame and is concealed by the fitting cover.
Steel mullions are 2" (51mm) wide and 3" (76mm) deep, with
a wall thickness of 1/8" (3mm).
Mullions are shipped with mounting screws and prepared for
strikes. Strikes are not included except where indicated.
Steel mullions are available in SP28 and SP313 finishes.
Consult factory for other powder coat finish options.
KR – Keyed removable steel mullions make removal faster
and easier by a single operation of the mortise cylinder. Once
mullion is removed, large equipment or furniture can freely
pass through the opening. The unit will self lock when reinstalled, without the use of the cylinder key. Uses a 1 1/4"
mortise cylinder with a straight cam (Schlage cam reference
B502-191). Cylinders are sold separately. Prefix mullion model
with “KR”.
Aluminum mullions are available in US4, US10, US28, 313 and
315 finishes. Consult factory for other powder coat finish
options. Aluminum mullion are not available keyed removable.
Stock hollow metal applications for devices mounted to cover
ANSI 161 cutouts are higher than the standard mullion strike
location. Consult the factory for special strike preparation or
order a blank mullion. See below.
Blank mullions are furnished without strike preparation. They
are used to mount devices at a strike height different from the
standard mullion preparation.
To order, specify:
1.For keyed Removable option on steel mullions, prefix
model number with “KR”
2.Model number
3.Height of opening
4.Finish
5. Handing if required
6.Centerline deviation (refer to device template for standard
centerline)
7.Strikes, when required, should be ordered with device
Keyed removable steel mullions
Steel mullions
1654Prepared for two 1606 strikes. If 1606 strikes are not
specified on the order, two per mullion will be added.
Additional charges apply.
4954Prepared for 264 or 299 strikes. For use with all Von
Duprin Panic rim devices.
9954Prepared for and must be used with two 268 strikes
(88-F device), or two 499F (22-F, 98-F, 99F devices).
UL fire labeled mullion for
up to 3 hour opening using
Von Duprin fire exit rim
devices. This mullion is not
easily removed due to
special fittings.
98-F and 99-F devices are
rated up to 10'0" (3048
mm).
Note: If 268 or 499F strikes are not specified on the
order, two per mullion will be added. Additional
charges apply.
4754Prepared for two 4263
monitor strikes.
4854Prepared for one 299 and
one 6111 electric strike.
Indicate handing for electric
strike.
Device options & accessories
Removable aluminum mullions are 1 1/16" (27mm) wide on face
closest to the door and 23/8" (60mm) at the widest point. The
depth is 3 1/8" (79mm) with a wall thickness of 1/8" (3mm).
Removable mullions
9854Prepared for one 268 or
499F strike and one 6111
electric strike. Indicate
handing for electric strike. UL fire labelled mullion for up
to 3 hour openings up to 8' x 8' (2438mm x 2438mm)
using Von Duprin fire exit rim devices
69
Von Duprin 98/99 Series • 69
98/99 Device options & accessories
Sex bolts
325 sex bolts used on surface Vertical Latches.
Sex bolts when ordered with devices
may be furnished with screw lengths
different than shown in Column B.
Below, Column B indicates popular
sizes. Sex Bolts ordered separately
are not furnished with screws. If
screws are required refer to chart
below and order screws by
description as a separate item. Other screw lengths may be used
based on minimum and maximum allowable thread
engagement, shown in column “C.” Quantity required — refer to
device section, quantities differ depending on outside trim.
425 sex bolts are required for 98/99 Series fire rated devices
when used on wood door applications. When wood doors are
specified for these devices, sex bolts will be added to the device
application unless SLM blocking package is specified.
825 sex bolts are required with 98-F/99-F rim
devices on wood door applications using NL,
TP, K and L outside trims. Two 825 sex bolts
will be added to the device application unless
SLM blocking package is specified.
To order, specify:
1.Model number
325
425
2.Quantity (2 per package)
3.Finish
Device options & accessories
4. Door thickness other than 1 3/4" (44mm)
825
Rim, mortise and concealed vertical
Center case
Device
type
Door
thickness
Sex bolt
Hinge case
B
/32" – 1 /16"
425
1 /16"
10-24 x 1" PPHMS
9
/32" – 1 9/16"
425
1 9/16"
10-24 x 11/2" PPHMS
9
/32" – 1 9/16"
425
1 9/16"
10-24 x 3/4" PPHMS
⁹9/32" – 1 9/16"
/32" – 1 9/16"
425
1 9/16"
10-24 x 11/4" PPHMS
9
425
1 /16"
10-24 x 1" PPHMS
9
425
1 9/16"
10-24 x 1 1/2" PPHMS
9
1 3/4" (44mm)
425
825A*
1 9/16"
1 13/16"
10-24 x 1" PPHMS
10-24 x 3/4" PPHMS
2 1/4" (57mm)
425
825B*
1 9/16"
25/16"
10-24 x 1 1/2" PPHMS
10-24 x 3/4" PPHMS
9
Surface vertical rod - latches only
Latch case
Door
thickness
Sex bolt
B
no.
A
Screw
1 /4" (44mm)
325
1 9/16"
1
2 1/4" (57mm)
325
1 9/16"
1
3
PPHMS – Pan phillips head machine screw
UFPHMS – Undercut flat phillips head machine screw
* For use with outside trims.
70• Von Duprin 98/99 Series
70
Screw
Screw
* For use with outside trims, see page XX for details
9827/9927/9827F,
9927F
A
A
98-F, 99-F*
Device
type
no.
no.
98, 9827, 9827-F,
1 3/4" (44mm)
9875, 9875-F, 9847,
9847-F, 9847WDC,
9849, 9849-F
99, 9927, 9927-F,
9975, 9975-F,
2 1/4" (57mm)
9947, 9947-F,
9949, 9949F,
98/9949WDC,
98/9949WDC-F
/4 - 20 x 3/4" FPHMS
/4 - 20 x 1/4" FPHMS
C
Thread
engagement
min. – max
C
Thread
engagement
min. – max
9
9
9
Sex bolt
B
9
/32" – 1 9/16"
/32" – 1 9/16"
/32" – 1 9/16"
98/99 Function, grade, type options
ANSI Function, grade & type
Function Grade 1,
type 1
Grade 1,
type 2
Grade 1,
type 3
Grade 1,
type 7
Grade 1,
type 7
Grade 1,
type 8
Grade 1,
type 8
Grade 1,
type 8
Grade 1,
type 9
1
98EO & F
99EO & F
9827EO & F
9927EO & F
9875EO & F
9975EO & F
9847WDCEO & F
9947WDCEO & F
9849WDCEO & F
9949WDCEO & F
9847EO & F
9947EO & F
9848EO & F
9948EO & F
9849EO & F
9949EO & F
9857EO & F
9957EO & F
2
98DT
99DT
9827DT
9927DT
9875DT
9975DT
9847WDCDT
9947WDCDT
9849WDCDT
9949WDCDT
9847DT
9947DT
9848DT
9948DT
9849DT
9949DT
9857DT
9957DT
3
98NL & F
99NL & F
9827NL & F
9927NL & F
9875NL & F
9975NL & F
9847WDCNL & F
9947WDCNL & F
9849WDCNL & F
9949WDCNL & F
9847NL & F
9947NL & F
9848NL & F
9948NL & F
9849NL & F
9949NL & F
9857NL & F
9957NL & F
3
98K-NL & F 9827K-NL & F 9875K-NL & F 9847WDCK-NL & F 9849WDCK-NL & F 9847K-NL & F
99K-NL & F 9927K-NL & F 9975K-NL & F 9947WDCK-NL & F 9949WDCK-NL & F 9947K-NL & F
9848K-NL & F 9849K-NL & F 9857K-NL & F
9948K-NL & F 9949K-NL & F 9957K-NL & F
3
98L-NL & F 9827L-NL & F
99L-NL & F 9927L-NL & F
9875L-NL & F 9847WDCL-NL & F 9849WDCL-NL & F 9847L-NL & F
9975L-NL & F 9947WDCL-NL & F 9949WDCL-NL & F 9947L-NL & F
9848L-NL & F 9849L-NL & F 9857L-NL & F
9948L-NL & F 9949L-NL & F 9957L-NL & F
5
98TP & F
99TP & F
9875TP & F
9975TP & F
7
98TP-2 & F
99TP-2 & F
8
98K & F
99K & F
9827K & F
9927K & F
8
98L & F
99L & F
9827L & F
9927L & F
10
98K-2 & F
99K-2 & F
9875K-2 & F
9975K-2 & F
10
98L-2 & F
99L-2 & F
9875L-2 & F
9975L-2 & F
9847WDCTP & F
9947WDCTP & F
9849WDCTP & F
9949WDCTP & F
9847TP & F
9947TP & F
9848TP & F
9948TP & F
9849TP & F
9949TP & F
9857TP & F
9957TP & F
9875K & F
9975K & F
9847WDCK & F
9947WDCK & F
9849WDCK & F
9949WDCK & F
9847K & F
9947K & F
9848K & F
9948K & F
9849K & F
9949K & F
9857K & F
9957K & F
9875L & F
9975L & F
9847WDCL & F
9947WDCL & F
9849WDCL & F
9949WDCL & F
9847L & F
9947L & F
9848L & F
9948L & F
9849L & F
9949L & F
9857L & F
9957L & F
9847WDC & F
9947WDC & F
9849WDC & F
9949WDC & F
9847TL & F
9947TL & F
9848 & F
9948& F
9849 & F
9949& F
9857TL & F
9957TL & F
9875TP-2 & F
9975TP-2 & F
9827TL & F
9927TL & F
14
98K-BE & F 9827K-BE & F
99K-BE & F 9927K-BE & F
9875K-BE & F 9847WDCK-BE & F 9849WDCK-BE & F 9847K-BE & F
9975K-BE & F 9947WDCK-BE & F 9949WDCK-BE & F 9947K-BE & F
9848K-BE & F 9849K-BE & F 9857K-BE & F
9948K-BE & F 9949K-BE & F 9957K-BE & F
14
98L-BE & F 9827L-BE & F
99L-BE & F 9927L-BE & F
9875L-BE & F 9847WDCL-BE & F 9849WDCL-BE & F 9847L-BE & F
9975L-BE & F 9947WDCL-BE & F 9949WDCL-BE & F 9947L-BE & F
9848L-BE &F 9849L-BE &F 9857L-BE & F
9948L-BE & F 9949L-BE & F 9957L-BE & F
16
9827TL-BE & F
9927TL-BE & F
9847WDC & F
9947WDC & F
9849WDC & F
9949WDC & F
9847TL-BE & F 9848 & F
9947TL-BE & F 9948 & F
9849 & F
9949 & F
9857TL-BE & F
9957TL-BE & F
Additional information
11 12
9827TP & F
9927TP & F
Dimensions
71
Von Duprin 98/99 Series • 71
UL Listing for fire exit hardware
UL Listed fire exit hardware label and opening size
Double door
Door
material
With 9954
Single door mullion
With 9854
mullion
With kr9954
mullion
With kr9854
mullion
Vxv
V x mortise
Vxv
same direction same direction double egress
98-F
99-F
Metal
3 Hour
4' x 10'
3 Hour
8' x 10'
3 Hour
8' x 10'
3 Hour
8' x 8'
3 Hour
8' x 8'
—
—
—
9875-F
9975-F
Metal
3 Hour
4' x 10'
—
—
—
—
—
3 Hour
8' x 10'
—
3 Hour
8' x 10'
3 Hour
8' x 10'
Additional information
Exit device
9827-F
9927-F
Metal
—
—
—
—
—
90 Minute
8' x 10'
9827LBR-F
9927LBR-F
Metal
—
—
—
—
—
90 Minute*
8' x 10'
—
3 Hour
8' x 10'
9857-F
9957-F
Metal
3 Hour
4' x 8'
3 Hour
8' x 8'
3 Hour
8' x 8'
3 Hour
8' x 8'
3 Hour
8' x 8'
—
—
—
3 Hour
8' x 10'
3 Hour
8' x 10'
*
9847-F
9947-F
Metal
—
—
—
—
—
90 Minute
8' x 10'
9847LBR-F
9947LBR-F
Metal
—
—
—
—
—
90 Minute*
8' x 10'
—
3 Hour
8' x 10'
9848-F
9948-F
Metal
—
—
—
—
—
90 Minute*
8' x 10'
3 Hour
8' x 10'
3 Hour
8' x 10'
9849-F
9949-F
Metal
—
—
—
—
—
90 Minute*
8' x 10'
3 Hour
8' x 10'
3 Hour
8' x 10'
9849LBL-F
9949LBL-F
Metal
—
—
—
—
—
90 Minute*
8' x 10'
—
3 Hour
8' x 10'
* Currently, no door manufacturers offer a listing over 90 minutes with doors swinging same direction.
Consult wood door manufacturers for current UL listings.
72• Von Duprin 98/99 Series
72
*
98/99 Finishes
A. Center case cover
B. Touch bar end cap
C. Touch bar trim
D. Cover plate
E. Mechanism end cap
F. Mechanism case
Finishes
US
number
BHMA
number
A, B, E
C
D&F
Bright brass
US3
605
Bright brass
Bright brass US3, 605
Buffed anodized
Satin brass
US4
606
Bright brass
Satin brass US4, 606
Anodized
Satin bronze
US10
612
Plated
Satin bronze US10, 612
Anodized
Bright chrome
US26
625
Plated
Bright stainless steel US32, 629
Buffed anodized
Satin chrome
US26D
626
Plated
Satin stainless steel US32D, 630
Anodized
Satin stainless steel*
US32D
630
Stainless steel
Satin stainless steel US32D, 630
Anodized
Aluminum, anodized
US28
628
Powder coat
Satin stainless steel US32D, 630
Anodized
Duranodic dark bronze
313
710
Powder coat
Powder coat
Powder coat
Black
315
622
Powder coat
Powder coat
Powder coat
Special Finishes
Color
US
number
BHMA
number
A, B, E
C
D&F
Satin bronze, oil-rubbed
US10B
613
Oil-rubbed, US10B
Oil-rubbed, US10B
Powder coat
Powder coat**
RAL #
–
Powder coat
Satin stainless steel US32D, 630
Powder coat
(unless specified to match device)
Bright bronze
US9
611
Plated
Bright bronze US9, 611
Buffed anodized
Satin nickel *
US15
619
Plated, clear powder
Satin stainless steel US32D
Anodized
Aged bronze 643E
–
–
Relieved aged bronze
Relieved aged bronze
Aged bronze, no
relief
Satin chrome
(antimicrobial)
U26D-AM
626-AM
AM Clear over chrome
AM Clear over satin stainless steel
US32D, 630
AM Clear over
anodized
Satin stainless steel
(antimicrobial)
US32D-AM
630-AM
AM Clear over stainless
steel
AM Clear over Satin Stainless Steel AM Clear over
US32D, 630
anodized
Finishes
Color
Touch bar trim options — Knurled
Embossed “Push”
Braille (Caution-Stairwell), satin stainless steel only
RSS, US32D only, red silk screen lettered “EMERGENCY EXIT ONLY – PUSH TO OPEN AND SOUND ALARM.”
* US32D and US15—available on 98 Series only
** Other custom logo touchbar trim and RAL color combinations available - consult factory
73
Von Duprin 98/99 Series • 73
98/99 Finishes
Finishes*
US
number
BHMA
number
Color
US
number
BHMA
number
Chromium,
polished
US26
625
Bronze, dull
US10
612
Anodized,
aluminum
US28
628
US15
619
Chromium, dull
US26D
626
Satin stainless
steel
US32D
630
Brass, polished
US3
605
Duranodic
dark bronze
313
710
Brass, dull
US4
606
Black
315
711
Finishes
Color
Satin nickel
Available for
35A ONLY
Special finishes
Color
US
number
BHMA
number
Satin chrome,
Antimicrobial
US26DAM
626-AM
Satin stainless
steel,
antimicrobial
US32DAM
630-AM
Aged bronze
643e
–
–
Pushpad options — Knurled
Embossed “Push”
Braille (Caution-Stairwell), satin stainless steel only
RSS – (Emergency Exit – Push to open and sound alarm) – Red Silkscreen lettering on US32D
* Note: Durable powder coated finishes available at specific special request. PLEASE CONTACT FACTORY.
74• Von Duprin 98/99 Series
74
About Allegion
Allegion (NYSE: ALLE) creates peace of mind by pioneering safety and security.
As a $2 billion provider of security solutions for homes and businesses, Allegion
employs more than 7,800 people and sells products in more than 120 countries
across the world. Allegion comprises 23 global brands, including strategic
brands CISA®, Interflex®, LCN®, Schlage® and Von Duprin®.
For more, visit www.allegion.com
© 2014 Allegion
006590, Rev. 04/14
www.allegion.com/us
Download PDF