Advantech | EDG-6528 | Product specifications | Advantech EDG-6528 Product specifications

Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
eConnectivity Solutions
eConnectivity
11
Connect Your Devices to the eWorld
11-2
eConnectivity Solutions Selection Guide
11-4
EDG-4504
4-port RS-232/422/485 to Ethernet Data Gateway
11-6
EDG-4508+ /4516+
EDG-4508R+/4516R+
(new)
8/16-port RS-232/422/485 to Ethernet Data Gateway with front wiring
8/16-port RS-232/422/485 to Ethernet Data Gateway with rear wiring
11-7
ADAM-4577/4579
1/2-port Universal Serial Device Gateway
11-8
ADAM-4570/4571
2/1-port RS-232/422/485 to Ethernet Data Gateway
11-9
ADAM-4570L/4571L
2/1-port RS-232 to Ethernet Data Gateway
11-10
ADAM-4572
1-port Modbus to Ethernet Data Gateway Module
11-11
Embedded Data Gateway Module
EDG-4100/4110
1-port RS-232, 422/485 to Ethernet Data Gateway module
11-12
EDG-4100W/4110W (new)
1-port wireless RS-232, 422/485 to Ethernet Data Gateway module
11-13
Network Hub/Switch/Fiber Optical Converter
ADAM-6510/6520
4/5-port Ethernet Hub/Switch
11-14
ADAM-6521
5-port Industrial 10/100 Mbps Ethernet Switch with Fiber Port
11-15
ADAM-6541
Ethernet to Multi-mode Fiber Optic Converter
11-16
ADAM-6542
Ethernet to Single Strand WPM Fiber Optic Converter
11-17
EDG-6528 (new)
8-port Industrial 10/100 Mbps Ethernet Switch
11-18
EDG-6528I (new)
8-port Industrial 10/100 Mbps Ethernet Switch w/Wide Operating
Temperature
11-18
EDG-6528M (new)
Industrial Switch with 6 10/100 Mbps Ethernet Ports & 2 Multi-mode Fiber
Ports
11-19
EDG-6528S (new)
Industrial Switch with 6 10/100 Mbps Ethernet Ports & 2 Single-mode Fiber
11-19
Ports
Wireless Gateway and Application Module
ADAM-4570W/4571W
(new)
2/1 port RS-232/422/485 to WLAN Data Gateway
11-20
WiCOM-3910 (new)
Wireless Remote & Monitor Display Extender
11-21
Communication Controller/Converter/Repeater
ADAM-6500/6501
Ethernet-based Communication Controller
11-22
ADAM-4500
PC-based Communication Controller
11-23
ADAM-4510/4510S
Isolated RS-422/485 Repeater
11-24
ADAM-4520
Isolated RS-232 to RS-422/485 Converter
11-24
ADAM-4521
Addressable RS-422/485 to RS-232 Converter
11-24
ADAM-4522
Isolated RS-232 to RS-422/485 Converter
11-25
ADAM-4541
Multi-mode Fiber Optic to RS-232/422/485 Converter
11-25
ADAM-4542+
Single-mode Fiber Optic to RS-232/422/485 Converter
11-25
ADAM-4561
1-port Isolated USB to RS-232/422/485 Converter
11-26
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-2
Evolve to eConnectivity
Ethernet Data Gateways
The Ethernet data gateways enable RS-232/422/485 serial devices to be connected to a
host computer over an Ethernet network quickly and cost-effectively. No extra programming
effort is required at the host computer, so software development costs can be saved.
Ethernet data gateways are especially suitable for remotely controlling and monitoring
your serial devices via Ethernet.
RS-232/422/485 to Ethernet Universal Data Gateway
Universal Serial Device Gateways allow RS-232/422/485 serial devices to connect
to Ethernet networks and operate as Ethernet nodes. Through TCP, UDP, IP, Socket or
Winsock, Universal Serial Device Gateways can be used for different operating systems
ranging from Microsoft Windows to Linux. Moreover, serial devices can use peer-to-peer
communication without any intermediate host PCs and software programming to save
costs and effort.
Modbus to Ethernet Data Gateway
The ADAM-4572 Modbus gateway serves as an interface between Modbus serial devices
and computer hosts running Modbus/TCP on Ethernet networks. Fully compliant with
Modbus/TCP, the ADAM-4572 offers a convenient solution to connect existing devices
or controllers running Modbus serial protocol (Modbus/ASCII or Modbus/RTU) to an
Ethernet network.
Introduction
As the world becomes more and more wired, it becomes critical to manage and connect
devices. Advantech offers a comprehensive and cost-effective eConnectivity solution for
easy installation and operation in critical industrial environments. This solution fulfills all
requirements from worldwide enterprises that need supervisory control, operator interfaces,
and logging of events and alarms via serial communication over Ethernet networks.
Advantech’s eConnectivity solution is divided into five parts:
 Industrial-grade hubs and switches
 Ethernet media converters
 Ethernet data gateways
 Web-enabled communication controllers
 Serial media converters
EDG System Architecture
eConnectivity Solutions
The Transparent Ethernet Data Gateway Board
The EDG-4100 is a cost effective network-enabled board module. It enables nearly any
device to communicate over the Internet and shared networks, and it allows those devices
to be remotely monitored, managed, and controlled. Thus, it is especially suitable for
remote management and data accessibility for devices that normally can’t connect to
a network. This includes: factory machinery, security systems, heating and ventilation
systems, lighting control system and Point-of-Sale devices.
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Bring Your Devices to the eWorld
Industrial-Grade Hubs and Switches
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
The industrial-grade hubs and switches (ADAM-6510/6520/6521) are especially suitable
for industrial environments with Ethernet networking needs, such as semiconductor
factories, inventory control at warehouses, assembly lines and production. Use them
to expand your industrial network fast and cost-effectively. The rugged industrial-grade
design assures reliability and stability.
IPPC
TPC
FPM
ATM & AWS
Ethernet Media Converters
DA&C
The Ethernet media converters are designed to convert Ethernet network signals (10/
100Base-TX) to fiber network signals (100Base-FX). They transparently convert Ethernet
signals into optic signals. Fiber optic communication provides wide bandwidth and secure
long-distance transmission without electromagnetic interference.
cPCI
ADAM-3000
Motion Control
ICOM
Web-enabled Communication
Controllers
eConnectivity
The Web-enabled communication controllers provide ideal environments to develop
applications that handle RS-232/485 devices/equipment data for Ethernet/Internet.
Advantech’s web-enabled communication controllers: ADAM-6500 and ADAM-6501,
with built-in Windows® CE .NET operating system, let you run new programs in Microsoft
embedded VC++. The Windows environment also includes a web server to allow you
to develop web-enabled applications. The result is a powerful solution for industrial
automation and control.
UNO
ADAM-4000
ADAM-5000
Serial Media Converters
ADAM-6000
The Serial Media Converters provide conversion between serial networks and other
media. They can transparently convert RS-232 signals to RS-422/485 signals, as well
as wireless and fiber optic signals. The ADAM-4520 transparently converts RS-232
signals into RS-422 or RS-485 signals without changing a PC's hardware or software.
The ADAM-4510S enables extension of serial network transmission. The ADAM-4541
can be used as a RS-232/422/485 point-to-point or point-to-multipoint connection for
transmitting and converting full/half-duplex signals and their equivalents within a fiber
optic environment.
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
11-3
Ethernet Data Gateway Series
Universal Serial
Device Gateway
Ethernet Data Gateway
Model Name
Interface
Ports
Serial Type
Transmission Speed
Surge Protection
EDG-4100
10/100 Mbps Ethernet
1
RS-232
50 ~ 230 kbps
-
EDG-4110
10/100 Mbps Ethernet
1
RS-422/485
50 ~ 230 kbps
-
ADAM-4571
10/100 Mbps Ethernet
1
RS-232/422/485
50 ~ 230 kbps
15 K VESD
ADAM-4571L
10/100 Mbps Ethernet
1
RS-232
50 ~ 230 kbps
15 K VESD
ADAM-4571S
10/100 Mbps Ethernet
1
RS-422/485
50 ~ 230 kbps
15 K VESD
ADAM-4570
10/100 Mbps Ethernet
2
RS-232/422/485
50 ~ 230 kbps
15 K VESD
ADAM-4570L
10/100 Mbps Ethernet
2
RS-232
50 ~ 230 kbps
15 K VESD
ADAM-4570S
10/100 Mbps Ethernet
2
RS-422/485
50 ~ 230 kbps
15 K VESD
EDG-4504
10/100 Mbps Ethernet
4
RS-232/422/485
50 ~ 230 kbps
15 K VESD
EDG-4508+
10/100 Mbps Ethernet
8
RS-232/422/485
50 ~ 230 kbps
15 K VESD
EDG-4508R+
10/100 Mbps Ethernet
8
RS-232/422/485
50 ~ 230 kbps
15 K VESD
EDG-4516+
10/100 Mbps Ethernet
16
RS-232/422/485
50 ~ 230 kbps
15 K VESD
EDG-4516R+
10/100 Mbps Ethernet
16
RS-232/422/485
50 ~ 230 kbps
15 K VESD
ADAM-4572
10/100 Mbps Ethernet
1
RS-232/422/485
300 ~ 115.2 kbps
N/A
ADAM-4577
10 Mbps Ethernet
1
RS-232/422/485
30 ~ 230 kbps
N/A
ADAM-4579
10/100 Mbps Ethernet
2
RS-232/422/485
30 ~ 230 kbps
N/A
Parity Bit
odd, even, none, space,
mark
odd, even, none, space,
mark
odd, even, none, space,
mark
odd, even, none, space,
mark
odd, even, none, space,
mark
odd, even, none, space,
mark
odd, even, none, space,
mark
odd, even, none, space,
mark
odd, even, none, space,
mark
odd, even, none, space,
mark
odd, even, none, space,
mark
odd, even, none, space,
mark
odd, even, none, space,
mark
odd, even, none
odd, even, none, space,
mark
odd, even, none, space,
mark
Data Bit
5,6,7,8
5,6,7,8
5,6,7,8
5,6,7,8
5,6,7,8
5,6,7,8
5,6,7,8
5,6,7,8
5,6,7,8
5,6,7,8
5,6,7,8
5,6,7,8
5,6,7,8
7,8
5,6,7,8
5,6,7,8
Wireless Data Gateway
Wireless Data Gateway
Model Name
Interface
Ports
Serial Type
Speed
Surge Protection
Parity
EDG-4100W
802.11b
1
RS-232
50 bps ~ 230 kbps
-
odd, even, none, space, mark
EDG-4110W
802.11b
1
RS-422/485
50 bps ~ 230 kbps
-
odd, even, none, space, mark
ADAM-4570W
802.11b
2
RS-232/422/485
50 bps ~ 230 kbps
15 K VESD
odd, even, none, space, mark
ADAM-4571W
802.11b
1
RS-232/422/485
50 bps ~ 230 kbps
15 K VESD
odd, even, none, space, mark
Ethernet Media Converters & Ethernet Hub/Switchs
Etherent
Media
Converters
Model Name
Ethernet
Hub
Ethernet Switches
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-4
Selection Guide
ADAM-6541
ADAM-6542/W15
ADAM-6542/W13
Interface
10/100 Mbps
100 Mbps
10/100 Mbps
100 Mbps
Ports
1
1
ADAM-6510
10 Mbps
4
ADAM-6520
10/100 Mbps
10/100 Mbps
100 Mbps
10/100 Mbps
10/100 Mbps
10/100 Mbps
100 Mbps
5
ADAM-6521
EDG-6528
EDG-6528I
EDG-6528M
EDG-6528S
eConnectivity Solutions
5
8
8
8
Connectors
1 x RJ-45
1 x Fiber
1 x RJ-45
1 x Fiber WDM
4 x RJ-45
1 x RJ-45 (uplink)
5 xRJ-45
4 x RJ-45
1 x Fiber
8 x RJ-45
8 x RJ-45
6 x RJ-45
2 x Fiber
Surge
Protection
ESD Protection
Power
Requirement
Operating Temperature
3000 VDC
1500 VRMS
10 ~ 30 VDC
0 ~ 70 °C (32 ~ 158 °F)
3000 VDC
1500 VRMS
10 ~ 30 VDC
0 ~ 70 °C (32 ~ 158 °F)
3000 VDC
-
10 ~ 30 VDC
0 ~ 70 °C (32 ~ 158 °F)
3000 VDC
-
10 ~ 30 VDC
0 ~ 70 °C (32 ~ 158 °F)
3000 VDC
-
10 ~ 30 VDC
0 ~ 65 °C (32 ~ 149 °F)
3000 VDC
3000 VDC
4000 VDC
4000 VDC
12 ~ 48 VDC
12 ~ 48 VDC
0 ~ 70 °C (32 ~ 158 °F)
-40 ~ 85 °C ( -40 ~ 185 °F)
3000 VDC
4000 VDC
12 ~ 48 VDC
0 ~ 70 °C (32 ~ 158 °F)
Software Utility
Max @ 128 pcs serial-connection
Drivers
Power
Requirements
1,1.5,2
Configuration/ Port Mapping
Serial: 8 pin header
Windows 98/NT/2000/XP
+ 5 VDC ± 5%
1,1.5,2
Configuration/ Port Mapping
Serial: 8 pin header
Windows 98/NT/2000/XP
+ 5 VDC ± 5%
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45
Serial: RJ-48
Windows® 98/NT/2000/XP
+ 10 ~ + 30 VDC
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45
Serial: DB9
Windows® 98/NT/2000/XP
+ 10 ~ + 30 VDC
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45
Serial: RJ-48
Windows® NT/2000/XP
+ 10 ~ + 30 VDC
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45
Serial: RJ-48
Windows® 98/NT/2000/XP
+ 10 ~ + 30 VDC
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45
Serial: RJ-48
Windows® 98/NT/2000/XP
+ 10 ~ + 30 VDC
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45
Serial: RJ-48
Windows NT/2000/XP
+ 10 ~ + 30 VDC
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45
Serial: DB-9
Windows® 98/NT/2000/XP
+ 10 ~ + 30 VDC
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45
Serial: RJ-48
Windows 98/NT/2000/XP
90 ~ 260 VAC
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45
Serial: RJ-48
Windows® 98/NT/2000/XP
90 ~ 260 VAC
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45
Serial: RJ-48
Windows 98/NT/2000/XP
90 ~ 260 VAC
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45
Serial: RJ-48
Windows® 98/NT/2000/XP
90 ~ 260 VAC
Socket or WinSocket
+ 10 ~ + 30 VDC
Connectors
Network: RJ-45 or 4 pin
header
Network: RJ-45 or 6 pin
header
®
®
®
®
1,2
Configuration
Network: Modbus/TCP
Modbus/Serial: Modbus/
ASCII, Modbus/RTU
1,1.5,2
Configuration
Network:RJ-45
Serial: DB9
Socket or WinSocket
+ 10 ~ + 30 VDC
1,1.5,2
Configuration
Network: RJ-45
Serial: RJ-48
Socket or WinSocket
+ 10 ~ + 30 VDC
Operating
Temperature
0 ~ 60 °C
(32 ~ 140 °F)
0 ~ 60 °C
(32 ~ 140°F)
0 ~ 60 °C
(32 ~ 140 °F)
0 ~ 60 °C
(32 ~ 140°F)
0 ~ 60 °C
(32 ~ 140 °F)
0 ~ 60 °C
(32 ~ 140 °F)
0 ~ 60 °C
(32 ~ 140°F)
0 ~ 60 °C
(32 ~ 140°F)
0 ~ 55 °C
(32 ~ 131 °F)
0 ~ 55 °C
(32 ~ 131 °F)
0 ~ 55 °C
(32 ~ 131 °F)
0 ~ 55 °C
(32 ~ 131 °F)
0 ~ 55 °C
(32 ~ 131 °F)
0 ~ 60 °C
(32 ~ 140 °F)
0 ~ 60 °C
(32 ~ 140 °F)
0 ~ 60 °C
(32 ~ 140°F)
IPPC
TPC
FPM
ATM & AWS
DA&C
cPCI
ADAM-3000
Motion Control
ICOM
Data Bit
Stop Bit
Software Utility
Connector
Driver
Power Requirement
Operating Temperature
5,6,7,8
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45 or 7 pin header
Serial: 8 pin header
Windows® 98/NT/2000/XP
+ 5 VDC ± 5%
0 ~ 60 °C (32 ~ 140 °F)
5,6,7,8
1,1.5,2
Configuration/ Port Mapping
Network: RJ-45 or 8 pin header
Windows® 98/NT/2000/XP
+ 5 VDC ± 5%
0 ~ 60 °C (32 ~ 140 °F)
5,6,7,8
1,1.5,2
Configuration/ Port Mapping
Max @ 128 pcs serial-connection
Network: RJ-45
Serial: RJ-48
Windows® 98/NT/2000/XP
+ 10 ~ + 30 VDC
0 ~ 60 °C (32 ~ 140 °F)
5,6,7,8
1,1.5,2
Configuration/ Port Mapping
Max @ 128 pcs serial-connection
Network: RJ-45
Serial: RJ-48
Windows® 98/NT/2000/XP
+ 10 ~ + 30 VDC
0 ~ 60 °C (32 ~ 140 °F)
Model Name
Interface
Ports
Transmission Speeds
Connectors
Isolation
Surge
Power
Requirement
ADAM-4510
RS-422/485
1
1200 bps ~ 115.2 kbps
RS-422/485: Plug-in screw terminal
-
-
+ 10 ~ + 30 VDC
ADAM-4510S
RS-422/485
1
1200 bps ~ 115.2 kbps
RS-422/485: Plug-in screw terminal
3000 VDC
-
+ 10 ~ + 30 VDC
ADAM-4520
RS232 to 422/485
1
1200 bps ~ 115.2 kbps
3000 VDC
-
+ 10 ~ + 30 VDC
ADAM-4522
RS232 to 422/485
1
1200 bps ~ 115.2 kbps
-
-
+ 10 ~ + 30 VDC
ADAM-4521
RS-422/485 to RS-232
1
300 bps ~ 115.2 kbps
1000 VDC
-
+ 10 ~ + 30 VDC
ADAM-4541/
4542+
Fiber Optic RS-232/
422/485
1
up to 115.2 kbps
-
-
+ 10 ~ + 30 VDC
ADAM-4561
USB RS-232/422/485
1
50 bps ~ 115.2 kbps
3000 VDC
3000 VDC
-
RS-232: Female DB9,
RS-422/485: Plug-in screw terminal
RS-232: Female DB9,
RS-422/485: Plug-in screw terminal
RS-232: Female DB9,
RS-422/485: Plug-in screw terminal
Fiber: ST
RS-232/422/485: Plug-in screw terminal
Network: USB type A connctor
(Type A to Type B cable provided)
Serial: twist-wire
Operating
Temperature
0 ~ 70 °C
(32 ~ 158 °F)
0 ~ 70 °C
(32 ~ 158 °F)
0 ~ 70 °C
(32 ~ 158 °F)
0 ~ 70 °C
(32 ~ 158 °F)
0 ~ 70 °C
(32 ~ 158 °F)
0 ~ 70 °C
(32 ~ 158 °F)
UNO
ADAM-4000
ADAM-6000
ADAM-8000
BAS
0 ~ 70 °C
(32 ~ 158 °F)
Online Download www.advantech.com/products
All product specifications are subject to change without notice
eConnectivity
ADAM-5000
Serial Media Converters
Serial Media Converters
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
Stop
Bits
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
Last updated : January 2005
11-5
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-6
EDG-4504
4-port RS-232/422/485 to
Ethernet Data Gateway
Features
 Automatic network connection recovery
 Auto-detects 10/100 Mbps Ethernet interface
 Supports an advanced security mechanism to avoid unauthorized access
 Tx/Rx LEDs for all ports to monitor data transmission
 Convenient and simple installation wizard
 Simple setup and configuration
Introduction
The EDG-4504 is an industrial-grade, network-based, serial device server for connecting four RS-232/422/485 devices, such as CNCs, PLCs, scales, and scanners,
directly to a TCP/IP network (Ethernet or Internet). Compared to similar devices on the market, it has a lower cost, great performance, and the most advanced features.
Both 10 Mbps and 100 Mbps Ethernet connections are supported, providing higher bandwidth, lower traffic impact, and more layout flexibility.
Specifications
Ordering Information
Hardware
 EDG-4504
 I/O Controller
 Memory
 Connector Type
16C954 or compatible (auto hardware flow control)
4 MB (4 ports)
DB9
Interface
 Network
 Serial
 Signals
10/100Base-T (10/100 Mbps)
RS-232/422/485
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
Performance
 Speed
 Max. No. of Ports
50 bps ~ 230.4 kbps
256 (per Windows® NT)
4-port RS-232/422/485 to Ethernet Data Gateway
Applications








Industrial/Factory automation
SCADA systems
Telecommunications
Automatic warehouse control
Building automation
Wafer fabrication systems
Self-service banking systems
Large scale retail systems
Configuration
 Parity
 Data Bits
 Stop Bits
None, even, odd, space, mask
5, 6, 7, 8
1, 1.5, 2
OS supported
 EDG-4504
Windows® 98/NT/2000/XP
Power and Environment
 Power Requirements 10 ~ 30 VDC
 Operating Temperature 0 ~ 55° C (32 ~ 131° F)
 Surge Protection
15,000 VESD
eConnectivity Solutions
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
EDG-4508+/4508R+
EDG-4516+/4516R+
8-port RS-232/422/485 to Ethernet
Data Gateway with Front/Rear Wiring
16-port RS-232/422/485 to Ethernet
Data Gateway with Front/Rear Wiring
Features
NEW
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Support local console, utility and remote Web configuration
 Support 8 DI/O channels for alarm/event control
 Optional dual power supply mechanism (EDG-4508+/4516+ only)
 Support advanced security mechanism to avoid unauthorized access
 Automatic connection recovery
IPPC
TPC
 Auto-detect 10/100 Mbps Ethernet interface
 Status LEDs for all ports Tx/Rx, mode and power
 Windows native COM port compatible drivers
FPM
 Rear Wiring (EDG-4508R+ and EDG-4516R+)
ATM & AWS
EDG-4516R+
EDG-4516+
DA&C
Introduction
EDG-4508+ and EDG-4516+ are industrial-grade network-based serial device servers for connecting up to 8 or 16 RS-232/422/485 devices, such as CNCs, PLCs, scales and
scanners, directly to a TCP/IP network (Ethernet or Internet). Compared with similar products on the market, EDG-4508+ and EDG-4516+ has a low cost, but offer high performance
with dual CPUs.
EDG-4508+ and EDG-4516+ provides many advanced features for both local and remote configuration through a software utility, V.24 console and the Web. To allow extra control,
EDG-4508+ and EDG-4516+ have built-in 4 digital input and 4 digital output channels on their back side. To enhance their reliability as device servers, EDG-4508+ and EDG-4516+
supports a redundant power mechanism for future expansions.
Both EDG-4508+ and EDG-4516+ supports 10/100 Mbps Ethernet connections for higher bandwidth, lower traffic impact and more layout flexibility. With Tx/Rx LEDs for all ports
and LEDs for mode and power on the front panel; operation, administration and maintenance are simplified.
*In default, only one power supply is included.
Power and Environment
Hardware
16C954 or compatible (auto hardware flow control)
Network: RJ-45
Serial: RJ-48
 Network
 Serial
 Signals
10/100Base-T
RS-232/422/485
TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
Performance
 Speed
 Max. No. of Ports
 Power Requirements 90 ~ 260 VAC, 47 ~ 63 Hz(optional dual power supply)
 Operating Temperature 0 ~ 55° C (32 ~ 131° F)
 Surge Protection
15,000 VESD
Ordering Information
 EDG-4508+
Interface
 EDG-4516+
 EDG-4508R+
50 bps ~ 230.4 kbps
256
 EDG-4516R+
Configuration
 Data Bits
 Stop Bits
 Parity
5, 6, 7, 8
1, 1.5, 2
None, even, odd, space, mark
 OPT1A
 OPT1D
Dry contact
Logic level 0: close to GND
Logic level 1: open
Open collector to 30 V, 200 mA max. load
Windows® 98/NT/2000/XP







I/O Type: 4 DI & 4 DO
 Digital Input
 Digital Output
 OS
8-port RS-232/422/485 to Ethernet Data Gateway
(1 pc of 30 cm RJ-48 to male DB9 RS-232/422/485
cable included)
16-port RS-232/422/485 to Ethernet Data Gateway
(1 pc of 30 cm RJ-48 to male DB9 RS-232/422/485
cable included)
8-port RS-232/422/485 to Ethernet Data Gateway with
Rear Wiring (1 pc of 30 cm RJ-48 to male DB9
RS-232/422/485 cable included)
16-port RS-232/422/485 to Ethernet Data Gateway
with Rear Wiring (1 pc of 30 cm RJ-48 to male DB9
RS-232/422/485 cable included)
1m RJ-48 to male DB9 RS-232/422/485 cable
30cm RJ-48 to male DB9 RS-232/422/485 cable
Motion Control
eConnectivity
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Applications
Industrial/Factory automation
SCADA systems
Telecommunications
Automatic warehouse control
Building automation
Self-service banking systems
Large scale retail systems
Online Download www.advantech.com/products
All product specifications are subject to change without notice
ADAM-3000
ICOM
Specifications
 I/O Controller
 Connector Type
cPCI
Last updated : January 2005
11-7
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-8
ADAM-4577
ADAM-4579
1-port Universal Serial Device Gateway
2-port Universal Serial Device Gateway
Features
 Supports 10/100Base-T (ADAM-4579); 10Base-T (ADAM-4577)
 Supports standard networking API: WinSock, Socket
 Provides multiple networking architectures: polling, event handling, peer-topeer
 Supports several AT-style commands to control (ADAM-4579)
 Allows a maximum of 8 host PCs to access with command response mode
using UDP protocol
 Supports any operating system with TCP/IP protocol: Windows®, Linux® etc.
 Auto-searching Windows configuration utility
 Download and testing utility: Easy to download firmware and self-diagnostic
 Easy to locate specific EDG series
 Surge protection for RS-485 line and power supply
 Mounts on DIN rail, panel or piggyback easily
Introduction
ADAM-4577 and ADAM-4579 are universal serial device gateways that bring RS-232/422/485 to Ethernet. They allow nearly any device with serial ports to connect and share an
Ethernet network. ADAM-4577 and ADAM-4579 provide a quick, simple and cost-effective way to bring the advantages of remote management and data accessibility to thousands
of devices that cannot connect to a network.
With ADAM-4577 or ADAM-4579, your existing serial devices can be used with the most popular operating systems on the market. There is no need to write special drivers for
specific operating systems. Moreover, you can make serial devices communicate with other devices peer-to-peer, without any intermediate host PCs and software programming. That
saves a lot of cost and effort. In addition, you can actively request data or issue commands from the RS-232/422/485 side or Ethernet side. This data can be sent bilaterally. Thus, the
ADAM-4577 and ADAM-4579 are especially suitable for remote monitoring environments such as security systems, factory automaton, SCADA, transportation and more.
For fulfilling the different applications that need network connectivity, ADAM-4577 provides 4 types of network architectures: polling, event-handling, peer-to-peer, and multi-host
access (UDP protocol). ADAM-4579 also provides 4 types of network architectures: polling, event-handling, peer-to-peer, and controlling.
Specifications
 Protocol
 Standard Networking
API
 Network Type
 Network Port
 Interface
 Port
 Connector





Transmission Speed
Parity Bit
Data Bit
Stop Bit
Diagnostic LEDs
 Utility Software
TCP/IP (ADAM-4579)
TCP/IP, UDP (ADAM-4577)
WinSock, Socket
ADAM-4577: polling, event handling, peer-to-peer,
multi-host access
ADAM-4579: polling, event handling, peer-to-peer,
controlling
IEEE 802.3, IEEE 802.3u
Network: 10Base-T (ADAM-4577); 10/100Base-T
(ADAM-4579)
Serial: 3-wire RS-232, RS-422, RS-485
ADAM-4577: 1 independent RS-232/422/485 port
ADAM-4579: 2 independent RS-232/422/485 ports
Network: RJ-45
Serial: ADAM-4577: DB-9
ADAM-4579: RJ-48 (RJ-48 to DB-9 cable
provided)
30 bps to 230 kbps
Odd, even, none, space, mark
5, 6, 7, and 8
1, 1.5, and 2
Network: TX/RX, Link, Speed (10/100 Mbps), Power
Serial: TX/RX, Status
Auto-detecting configuration utility (up to 128 devices)
Easy-to-diagnose download & testing utility
UDP testing utility (ADAM-4577)
 Power Requirements
 Power Consumption
 Mounting
Unregulated 10 ~ 30 VDC with surge protection
2 W (ADAM-4577); 4 W (ADAM-4579)
DIN-rail, panel mounting, piggyback stack
Environmental Specifications




Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
0 ~ 60° C (32 ~ 140° F)
-20 ~ 80° C (-4 ~ 176° F)
20 ~ 95% (non-condensing)
0 ~ 95% (non-condensing)
Ordering Information
 ADAM-4577
 ADAM-4579
 OPT1A
 OPT1D
1-port Universal Serial Device Gateway
2-port Universal Serial Device Gateway
(2 pcs of 1 m RJ-48 to male DB9 RS-232/422/485
cable included)
1m RJ-48 to male DB9 RS-232/422/485 cable
30cm RJ-48 to male DB9 RS-232/422/485 cable
eConnectivity Solutions
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
ADAM-4570
ADAM-4571
2-port RS-232/422/485 to Ethernet
Data Gateway
1-port RS-232/422/485 to Ethernet
Data Gateway
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Supports 10/100Base-T Ethernet port
 Supports high transmission speeds up to 230 kbps
 Supports an advanced security mechanism to avoid unauthorized access
 Auto-reconnection
 Remote download firmware
IPPC
TPC
 Auto-detecting
 Easy-managing Port Mapping Utility
 Supports Windows® 98/NT/2000/XP driver
FPM
 Surge protection for RS-485 line and power supply
 Automatic RS-485 data flow control
ATM & AWS
DA&C
Introduction
ADAM-4570 and ADAM-4571 are lightning fast and cost effective data gateways between RS-232/422/485 and Ethernet interfaces. These units immediately upgrade your existing
device(s) to the Ethernet world. Functionally transparent and efficient, the ADAM-4570 and ADAM-4571 are specially designed for remotely controlling and monitoring devices via
the Internet.
cPCI
ADAM-3000
One or two RS-232/422/485 serial ports can each be easily configured for your needs. There is also support for transmission speeds up to 230 kbps, which meets the demand for
today’s high-speed data exchanges. You can use a Windows® utility to configure the units without need for further programming. ADAM-4570 and ADAM-4571 not only protect your
current hardware investment but also ensure future network expandability. Since the protocol conversion is transparent, all existing devices can be seamlessly integrated into the
Motion Control
Ethernet network. Therefore, ADAM-4570 and ADAM-4571 can be used in security systems, factory automation, SCADA, transportation and more.
The units integrate both your existing human-machine interface software (HMI) and RS-232/422/485 system architecture with an Ethernet network. The result helps save cabling
space and software development costs. ADAM-4570/ and ADAM-4571 also provide a high-performance RISC CPU and real-time operating system to reduce CPU load. These
components make the units more stable and reliable. Another benefit is the ability to remotely download programs to a designated device via Ethernet. This reduces the need for ICOM
on-site maintenance and diagnosis.
A Windows configuration and port-mapping utility is also included. This configuration tool can auto-detect all Ethernet Data Gateway devices on a local network, and helps users
to easily adjust all settings. The port mapping utility helps to set up COM ports for one Windows® 95/98/NT/2000/XP platform. This helps you configure all ports to meet your eConnectivity
requirements.
Specifications
Protocol
Network
Port
Connector
Ordering Information
TCP/IP
10/100Base-T Ethernet
1/2 Independent RS-232/422/485 ports
Network: RJ-45
Serial: RJ-48 (RJ-48 to DB9 cable provided)
 Transmission Speed
50 bps ~ 230 kbps
 Parity Bits
Odd, even, none, space, mark
 Data Bits
5, 6, 7, 8
 Stop Bits
1, 1.5, 2
 Diagnostic LEDs
Network: Tx/Rx, Link , Speed (10/100 Mbps), Power
Serial: Tx/Rx, Status
 Surge Protection
15 K VESD (RS-232/422/485)
 Utility Software
Auto-detecting configuration utility (up to 128 devices)
port mapping utility
 Drivers Supported
Windows® 98/NT/2000/XP
 Power Requirements Unregulated 10 to 30 VDC
 Power Consumption
4 watt
• Mounting
DIN-rail, panel mounting, piggyback stack
 Operating Temperature 0 ~ 60° C (32 ~ 140° F)
 Storage Temperature -20 ~ 80° C (-4 ~ 176° F)
 Operating Humidity
20 ~ 95% (non-condensing)
 Storage Humidity
0 ~ 95% (non-condensing)




 ADAM-4571
 ADAM-4570
 OPT1A
 OPT1D
UNO
1-port RS-232/422/485 to Ethernet Data Gateway
(1 pc of 1 m RJ-48 to male DB9 RS-232/422/485 cable
ADAM-4000
included)
2-port RS-232/422/485 to Ethernet Data Gateway
(2 pcs of 1 m RJ-48 to male DB9 RS-232/422/485
cable included)
ADAM-5000
1m RJ-48 to male DB9 RS-232/422/485 cable
30cm RJ-48 to male DB9 RS-232/422/485 cable
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
11-9
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-10
ADAM-4570L
ADAM-4571L
2-port RS-232 to Ethernet
Data Gateway
1-port RS-232 to Ethernet
Data Gateway
Features
 Supports 10/100Base-T Ethernet
 Supports high transmission speeds up to 230 kbps
 Supports an advanced security mechanism to avoid unauthorized access
 Auto-reconnect
 Remote download firmware
 Auto-detecting
 Easy-managing Port Mapping Utility
 Supports Windows® 98/NT/2000/XP driver
Introduction
ADAM-4570L and ADAM-4571L are cost-effective data gateways that connects RS-232 and Ethernet interfaces. It provides a quick and low-cost way to connect any RS-232 device
with an Ethernet network. Through networking transparency features, ADAM-4570L and ADAM-4571L make it possible to cut costs by using existing hardware and software. The
units also bring the advantages of remote management and data accessibility to RS-232 devices.
ADAM-4570L and ADAM-4571L provide one or two RS-232 serial ports. The transmission speed of the units is up to 230 kbps, meeting the demands for high-speed data exchanges. In
addition, you can use Windows® utilities to configure the ADAM-4570L and ADAM-4571L without further programming. The units not only protects your current hardware investment
but also ensures future network expandability. Since the protocol conversion is transparent, all your existing devices can be seamlessly integrated with an Ethernet network.Therefore,
ADAM-4570L and ADAM-4571L can be used in security systems, factory automation, SCADA, transportation and more.
ADAM-4570L and ADAM-4571L link both your existing human-machine interface (HMI) PC and your RS-232 devices with Ethernet cables. The result extends your access from
local RS-232 to global Ethernet/Internet. Another benefit is that the units allow users to remotely download programs to a designated device via Ethernet. This reduces the need for
on-site maintenance and diagnosis.
Lastly, ADAM-4570L and ADAM-4571L come with a Windows® configuration and port-mapping utility. The configuration tool can auto-detect all Ethernet Data Gateway devices
on the local network, and let you easily adjust all settings. The port mapping utility helps you to set up COM ports for one Windows® 95/98/NT/2000/XP platform. This helps you
configure all ports to meet your needs.
Specifications
Protocol
Network
Port
Connector
TCP/IP
10/100Base-T Ethernet
1/2 Independent RS-232 ports
Network: RJ-45
Serial: RJ-48 (ADAM-4570L)
DB9 (ADAM-4571L)
 Transmission speed
50 bps to 230 kbps
 Parity Bits
Odd, even, none, space, mark
 Data Bits
5, 6, 7, 8
 Stop Bits
1, 1.5, 2
 Diagnostic LEDs
Network: Tx/Rx, Link , Speed (10/100 Mbps),
Power Serial: Tx/Rx, Status
 Utility Software
Auto-detecting Configuration Utility (up to 128 devices)
Port mapping utility
 Drivers Supported
Windows® 98/NT/2000/XP
 Power Requirements Unregulated 10 to 30 VDC
 Power Consumption
1.5 watt (ADAM-4570L)
1.5 watt (ADAM-4571L)
 Mounting
DIN-rail, panel mounting, piggyback stack
 Operating Temperature 0 ~ 60° C (32 ~ 140° F)
 Storage Temperature -20 ~ 80° C (-4 ~ 176° F)
 Operating Humidity
20 ~ 95% (non-condensing)
 Storage Humidity
0 ~ 95% (non-condensing)




eConnectivity Solutions
Ordering Information
 ADAM-4571L
 ADAM-4570L
 OPT1A
 OPT1D
1-port RS-232 to Ethernet Data Gateway
2-port RS-232 to Ethernet Data Gateway
(2 pcs of 1 m RJ-48 to male DB9 RS-232/422/
485cable included)
1m RJ-48 to male DB9 RS-232/422/485 cable
30cm RJ-48 to male DB9 RS-232/422/485 cable
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
ADAM-4572
1-port Modbus® to Ethernet
Data Gateway
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Supports 10/100 Mbps communication speeds
 Allows up to 8 clients to access field data simultaneously
 Supports popular HMI software with Modbus/TCP driver or OPC server
 Up to 3 Independent serial ports capacity if configured to RS-485 serial mode
 Provides auto-searching device ID Windows utility
IPPC
TPC
 Surge protection for RS-485 and power line
 Automatic RS-485 data flow control
 Easy mounting on DIN-rail , panel piggyback
FPM
 Supports Modbus/ASCII, RTU Protocol to control devices
ATM & AWS
DA&C
Introduction
cPCI
ADAM-4572 serves as an interface between Modbus® serial devices and computer hosts running Modbus/TCP on an Ethernet network. Fully compliant with Modbus/TCP, it is ideal
for those who looking for an easy way to connect their existing devices or controllers running Modbus serial protocols (Modbus/ASCII or Modbus/RTU) to Ethernet networks. It works
like a bridge between Modbus® serial devices and controllers over TCP/IP Ethernet networks. Benefits are also abundant for customers who want to expand their Ethernet-based
ADAM-3000
Modbus® (Modbus/TCP) applications.
Networks have become increasingly vital for industrial automation applications, but many control devices today do not have a network port and can only communicate with a dedicated
local PC or control panel. Advantech’s revolutionary network-enabling technology is now allowing control devices with serial ports to connect to the Ethernet and share networks
quickly and cost-effectively. The ADAM-4572 Modbus to Ethernet Data Gateway allows users to integrate new and existing Modbus/RTU and Modbus/ASCII serial devices to newer Motion Control
TCP/IP network-based devices. Manufacturers, system integrators, and end users can now use the ADAM-4572 to create networked applications to remotely manage and access data
from control devices no matter where they are.
ADAM-4572 provides features such as: 10/100 Mbps data rate for Ethernet/Fast Ethernet connection, serial port speed up to 115.2 kbps, auto-searching device, Modbus® RTU, ICOM
Modbus/ASCII, Modbus/TCP protocol, diagnostic LEDs, RJ-45 connectors and surge protection on network. This represents a true communication Data Gateway between Ethernet
and Modbus, and an easy choice when your factory needs improved network integration and resource sharing.
eConnectivity
Specifications
 Protocols










Environmental Specifications
Ethernet: Modbus/TCP
Serial: Modbus/RTU, Modbus/ASCII
Network Port
10Base-T (IEEE 802.3) 100Base-TX (IEEE 802.3u)
RJ-45 connector
Serial Port
RS-232/422/485
plug-in screw terminal
Transmission speed: 300 bps to 115.2 kbps
Parity: odd, even, none
Data bit: 7, 8
Stop bit: 1, 2
Compatibility
Ethernet /IEEE 802.3, IEEE 802.3u
Modbus/Serial: Modbus/ASCII, Modbus/ RTU
Network: Modbus/TCP
Diagnostic LEDs
Network: Tx/Rx, Link, Speed (10/100 Mbps), Power
Serial: Status, Tx/Rx
Utility Software
Windows-based, device auto-searching (up to 128
devices)
Device Setting: name, description, serial port
Compatible with application software running on Modbus/TCP standard
Power Requirements Unregulated 10 ~ 30 VDC
Power Consumption
3W
Case
ABS with captive mounting hardware
Mounting
DIN-rail, Panel mounting, piggyback stack




Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
UNO
0 ~ 60° C
-20 ~ 80° C
20 ~ 95% (non-condensing)
0 ~ 95% (non-condensing)
ADAM-4000
Ordering Information
 ADAM-4572
1-port Modbus® to Ethernet Data Gateway
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
ADAM-5000
Last updated : January 2005
11-11
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-12
EDG-4100
EDG-4110
1-port RS-232 to Ethernet Data Gateway Module
1-port RS-422/485 to Ethernet Data Gateway Module
Features
 Supports 10/100Base-T Ethernet standard
 Supports high transmission speeds up to 230 kbps
 Supports LED indicators for easy diagnosis
 Provides RS-232 (EDG-4100), 422/485 (EDG-4110) interfaces
 Supports TCP/IP protocol
 Provides 8 universal digital inputs/outputs for emergent ON/OFF control
 Easy configuration via utility
 Supports Windows® 98/NT/2000/XP driver
 Automatic RS-485 data flow control (EDG-4110)
 Easy to mount through backside PIN connectors
Introdution
EDG-4100 and EDG-4110 are fast and cost-effective network-enabled board modules. EDG-4100 provides one RS-232 port, while EDG-4110 provides one RS-422/485 port. The
modules enable nearly any device to communicate over the Internet and shared networks, and they allow network devices to be remotely monitored, managed, and controlled. Functionally
transparent and efficient, EDG-4100 and EDG-4110 provide a complete software and hardware solutions. The modules effectively eliminate the need for OEMs and systems integrators
to invest engineering resources to develop Ethernet networking solutions, and reduce the time it takes to bring intelligent devices to market. Thus, the modules are especially suitable
for remote management and data accessibility to thousands of devices that cannot previously could not connect to the network such as: factory machinery, security systems, heating
and ventilation systems, lighting control systems and Point-of-Sale devices.
EDG-4100 and EDG-4110 are 54 x 59 mm Ethernet-enabled boards, so they can easily fit into almost any device. Pin headers are provided to connect LAN, DI/O, power and
RS-232/422/485 into your boards, for a quick and cost-effective method to connect the system to the Internet. There are also 8 DI/O, which provides additional flexibility.
EDG-4100 and EDG-4110 replace expensive dedicated PCs or lengthy serial cables with fast and reliable networking technology.
Specifications
Ordering Information
 Protocol
 Compatibility
 Interface
 EDG-4100
 EDG-4110
TCP/IP
IEEE 802.3, IEEE 802.3u
Network: 10/100 Base-T Ethernet
Serial: RS-232 (EDG-4100)
RS-422/485 (EDG-4110)
 Port
1 Independent RS-232 port (EDG-4100)
1 Independent RS-422/485 port (EDG-4110)
 Connector
Network: RJ-45 or 4-pin header
Serial: 8-pin header
 DI/DO
4DI, 4DO
 Transmission Speeds 50 bps ~ 230 kbps
 Parity Bits
Odd, even, none, space, mark
 Data Bits
5, 6, 7, 8
 Stop Bits
1, 1.5, 2
 Diagnostic LEDs
Network: Tx /Rx, Link, Speed
 Utility Software
Configuration utility
Port mapping utility
 Driver Support
Windows® 98/NT/2000/XP
 Power Requirement
5 VDC ± 5%
 Power Consumption
0.6 W @ 10 M, 0.9 W @ 100 M
 Operating Temperature 0 ~ 60° C (32 ~ 140° F)
 Storage Temperature -20 ~ 80° C (-4 ~ 176° F)
 Operating Humidity
20 ~ 95% (non-condensing)
 Storage Humidity
0 ~ 95% (non-condensing)
1-port RS-232 to Ethernet Data Gateway Module
1-port RS-422/485 to Ethernet Data Gateway Module
eConnectivity Solutions
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
EDG-4100W
EDG-4110W
NEW
1-port RS-232 to WLAN Data Gateway
Module
1-port RS-422/485 to WLAN Data
Gateway Module
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Supports 802.11b standard
 Supports high transmission speeds up to 230 kbps
IPPC
 Supports LED indicators for easy diagnosis
 Provides RS-232 (EDG-4100W), 422/485 (EDG-4110W) interfaces
 Supports TCP/IP protocol
TPC
 Provides 8 universal digital inputs/outputs for emergent ON/OFF control
 Easy configuration via utility
 Supports Windows® 98/NT/2000/XP driver
FPM
 Automatic RS-485 data flow control (EDG-4110W)
 Easy to mount through backside PIN connectors
ATM & AWS
DA&C
Introduction
cPCI
EDG-4100W and EDG-4110W are fast and cost-effective 802.11b wireless networking-enabled board modules. EDG-4100W provides one RS-232 port, while EDG-4110W provides
one RS422/485 port. The modules enable nearly any device to communicate with 802.11b wireless LAN and shared networks, and they allow those devices to be remotely monitored,
managed, and controlled. Functionally transparent and efficient, EDG-4100W and EDG-4110W provide a complete software and hardware solution. The modules effectively eliminates
ADAM-3000
the need for OEMs and systems integrators to invest engineering resources to develop 802.11b wireless Ethernet networking solutions, and reduces the time it takes to bring intelligent
devices to market. Thus, the modules are especially suitable to provide remote management and data accessibility to thousands of devices that cannot connect to the network such
as factory machinery, security systems, heating and ventilation systems, lighting control systems and Point-of-Sale devices.
EDG-4100W and EDG-4110W are 54 x 59 mm wireless networking-enabled boards, so they can easily fit into almost any device. A wireless antenna is provided to connect to the Motion Control
802.11b wireless LAN and pin headers are provided to connect DI/O, power and RS-232/422/485 into your boards. There are also 8 DI/O, which provides additional flexibility.
EDG-4100W and EDG-4110W replaces expensive dedicated PCs or lengthy serial cables with fast and reliable networking technology.
Specifications
Ordering Information
 Protocol
 Network
 Port
 EDG-4100W
 EDG-4110W
TCP/IP
802.11b
1 Independent RS-232 port (EDG-4100W)
1 Independent RS-422/485 port (EDG-4110W)
 Connector
WLAN: 802.11b antenna
Serial: 8 pin header
 DI/DO
4DI, 4DO
 Transmission Speeds 50 bps ~ 230 kbps
 Parity Bit
odd, even, none, space, mark
 Data Bit
5, 6, 7, 8
 Stop Bit
1, 1.5, 2
 Diagnostic LEDs
W-LAN: Active, Link
 Utility Software
Auto-detecting configuration utility
Port mapping utility
 Driver Support
Windows® 98/NT/2000/XP
 Power Requirement
5 VDC ± 5%
 Power Consumption
Max @ 3 Watt
 Operating Temperature 0 ~ 60° (32 ~ 140°)
 Storage Temperature -20 ~ 80° (-4 ~ 176°)
 Operating Humidity
20 ~ 95% (non-condensing)
 Storage Humidity
0 ~ 95% (non-condensing)
ICOM
1-port RS-232 to WLAN Data Gateway Module
1-port RS-422/485 to WLAN Data Gateway Module
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
eConnectivity
Last updated : January 2005
11-13
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-14
ADAM-6510
ADAM-6520
4-port Industrial 10 Mbps
Ethernet Hub
5-port Industrial 10/100
Mbps Ethernet Switch
Features
 Supports full/half duplex flow control (ADAM-6520)
 Supports Integrated Loop-up engine (ADAM-6520)
 Supports MDI/MDI-X auto crossover (ADAM-6520)
 Provides broadcast storm protection (ADAM-6520)
 Supports +10 ~ 30 VDC voltage power input
 Provides surge protection 3000VDC for power line
 Provides flexible mounting: DIN rail, panel, piggyback
 Supports operating temperatures from -10 ~ 70° C
Introduction
ADAM-6510 is a 4-port industrial-grade hub with Ethernet connectivity and 10 Mbps transfer rate. ADAM-6520 is a 5-port industrial-grade switch with Ethernet connectivity and from
10 to 100 Mbps transfer rates. (Auto-senses transfer rate).
Just like any other product in the ADAM® family, ADAM-6510 and ADAM-6520 can be mounted in three different ways: DIN rail, panel and piggyback. Solid industrial-grade design
assures reliable operation in common application areas like: semi-conductor factories, inventory control environments, assembly lines, manufacturing and many more.
Both modules support a wide voltage range of +10 ~ 30 V DC over the terminal block, and 3,000 V DC surge protection ensures that over-voltage is no concern. The wide operating
temperature of ADAM-6510 and ADAM-6520 goes from -10 to 70° C (14 to 158° F). This permits them to be functional in harsh operating environments.
The six inclusive LED indicators make troubleshooting of the modules easier. Each port has a pair of LEDs that indicate link status and port activities. This easily informs users of any
collisions, the link status, power failure and data receipts for immediate on-site diagnosis.
Specifications
ADAM-6510
Common










Compatibility
Surge Protection
LED
Power Requirements
Power Consumption
IEEE 802.3, IEEE 802.3u
3000 VDC (Power)
Power, 10/100 Mbps
Unregulated 10 ~ 30 VDC
2 Watt (ADAM-6510)
2.4 Watt (ADAM-6520)
Case
ABS/PC with captive mounting hardware
Mounting
DIN-rail, panel mounting, piggyback stack
Operating Temperature -10 ~ 70° C (14 ~ 158° F)
Storage Temperature -20 ~ 80° C (-4 ~ 176° F)
Operating Humidity
20 ~ 95 % (non-condensing)
 Storage Humidity
 Interface
 Port
 Connector
Network: 10Base-T Ethernet
4 x 10 Mbps , 1 x 10 Mbps uplink
RJ-45
ADAM-6520
 Interface
 Port
 Connector
Network: 10/100Base-T Ethernet
5 x 10/100 Mbps
RJ-45
Ordering Information
 ADAM-6510
 ADAM-6520
4-port Industrial 10 Mbps Ethernet Hub
5-port Industrial 10/100 Mbps Ethernet Switch
0 ~ 95 % (non-condensing)
eConnectivity Solutions
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
ADAM-6521
5-port Industrial 10/100 Mbps
Ethernet Switch with Fiber Port
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Supports 1 port 100 Mbps multimode Fiber duplex SC & 4-port 10/100
Mbps RJ-45 connectors
 Supports full/half duplex flow control
 Supports Integrated Loop-up engine
 Supports MDI/MDI-X auto crossover
IPPC
TPC
 Provides broadcast storm protection
 Supports +10~ 30 VDC voltage power input
 Provides surge protection 3000VDC for power line
FPM
 Provides flexible mounting: DIN rail, panel, piggyback
 Supports operating temperatures from -10 ~ 65° C
ATM & AWS
DA&C
Introduction
ADAM-6521 is an industrial-grade Ethernet switch with fiber optic ports that makes it possible to expand industrial networks fast and cost-effectively. ADAM-6521 consists of 1 fiber
port and 4 RJ-45 ports. With fiber optics, you can prevent noise interfering with your system and implement transmission distances up to 2 km.
cPCI
ADAM-6521 is especially suited for industrial environments with Ethernet networking needs such as: semi-conductor factories, inventory control environments, assembly line and ADAM-3000
production and more.
Like other products in the ADAM® family, ADAM-6521 can be mounted in three different ways: DIN rail, panel and piggyback, suitable for any industrial environment.
ADAM-6521 supports a wide voltage range of +10 ~ 30 VDC over the terminal block, and 3,000 V DC surge protection to protect it from being damaged by over-voltage. A wide operating Motion Control
temperature range from -10 to 65° C (14 ~ 149° F), makes it functional in harsh operating environments.
The six inclusive LED indicators make troubleshooting the ADAM-6521 easier. Each port has a pair of LEDs that indicate link status and port activities. This function conveniently
informs users of any collisions, the link status, power failure and data receipts for immediate on-site diagnostics.
ICOM
Specifications















Compatibility
Surge Protection
LEDs
Transmission Distance
Power Requirements
Power Consumption
Case
Mounting
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Interface
Port
Connector
Ordering Information
IEEE 802.3, IEEE 802.3u
3000 VDC (Power)
Power, 10/100 Mbps
2000 m (fiber)
Unregulated 10 to 30 VDC
3.5 W
ABS/PC with captive mounting hardware
DIN-rail, panel mounting, piggyback stack
-10 ~ 65° C (14 ~ 149° F)
-20 ~ 80° C (-4 ~ 176° F)
20 ~ 95 % (non-condensing)
0 ~ 95 % (non-condensing)
Network: 10/100Base-T & 100Base-FX Ethernet
4 x 10/100 Mbps (RJ-45), 1 x 100 Mbps (Fiber)
4 x RJ-45 & 1 x Fiber (SC type)
 ADAM-6521
eConnectivity
5-port Industrial 10/100 Mbps Ethernet Switch with
Fiber port
UNO
ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
11-15
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-16
ADAM-6541
Ethernet to Multi-Mode
Fiber Optic Converter
Features
 Supports 1-port 100 Mbps multimode fiber optics
 Supports 10 ~30 VDC power input
 Easily mounted on a DIN-rail, panel or piggyback
 Supports full/half-duplex flow control.
 Supports MDI/MDIX auto crossover.
 Embedded with a switch controller, supports auto-negotiation.
 Embedded with memory buffer, supports store and forward transmission.
Introduction
ADAM-6541 is an industrial-grade converter that is designed to convert Ethernet network signals (10/100Base-TX) to fiber networks (100Base-FX). It transparently converts Ethernet
signals into optic signals. The advantages of fiber optics are wide bandwidth, EMI immunity and its suitability for long-distance transmissions. Therefore, ADAM-6541 is an ideal
solution for “fiber to building” applications at central offices or local sites.
ADAM-6541 supports MDI/MDIXauto detection so no crossover wire is necessary. It also includes a switch controller that can sense transmission speed (10/100 Mbps) automatically.
Both the Ethernet port and fiber port have memory buffers that support store-and-forward mechanism, this assures that data can be transmitted properly.
ADAM-6541 is extremely compact and it can be mounted in three different ways. DIN rail, panel and piggyback. It works normally at -10 to 70°C and accepts wide unregulated voltage
range from +10 ~ 30 VDC. Besides, it also has 3,000 VDC surge protection against over-voltage so it is suitable for harsh operating environments.
The ADAM-6541 provides three LED indicators: Power, LNK/ACT, and 10/100Mbps, which let you troubleshoot easier.
Specifications
Interface
Port
Connector
Compatibility
Surge Protection
Isolation
LEDs
Transmission Distance
Network: 10/100Base-TX & 100Base-FX standard
1 x 10/100 Mbps (RJ-45), 1 x 100 Mbps (Fiber)
1 x RJ-45 & 1 x Fiber (SC type)
IEEE 802.3, IEEE 802.3u
3,000 VDC (Power)
1,500 Vrms (Ethernet port)
Power, LNK/ACT, 10/100Mbps
Multi mode fiber: 50/125, 62.5/125 or 100/140 µm
Multi mode fiber, 412 m for half duplex, 2 km for full
duplex.
 Power Requirement
Unregulated 10 ~ 30 VDC
 Power Consumption
3W
 Case
ABS/PC with captive mounting hardware.
 Mounting
DIN-rail, panel mounting, piggyback stack
 Operating Temperature -10 ~ 70 °C
 Storage Temperature -20 ~ 80 °C
 Operating Humidity
20 ~ 95% (non-condensing)
 Storage Humidity
0 ~ 95% (non-condensing)








Ordering Information
 ADAM-6541
Ethernet to Multi-Mode Fiber Optic Converter
eConnectivity Solutions
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
ADAM-6542
Ethernet to Single Strand
WDM Fiber Optic Converter
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Supports 1-port 100 Mbps single strand fiber optics
 Supports 10 ~30 VDC power input
IPPC
 Easily to mounted on a DIN-rail, panel or piggyback
 Provides 100Base-FX WDM single strand fiber
 Supports MDI/MDIX auto crossover.
TPC
 Embedded with a switch controller, supports auto-negotiation.
 Embedded with the memory buffer, supports store and forward transmission.
FPM
ATM & AWS
DA&C
Introduction
ADAM-6542 is an industrial-grade converter that is designed to convert Ethernet networks to fiber networks. It does so by transparently converting Ethernet signals to optic signals.
The advantages of fiber optics are wide bandwidth, EMI immunity and long-distance transmission capability. Therefore, ADAM-6542 is an ideal solution for “fiber to building”
applications at central offices or local sites.
cPCI
ADAM-3000
ADAM-6542 uses WDM (Wavelength Division Multiplexing) technology, which increases the information-carrying capacity of fiber by multiplex transmission and reception of signals
at different wavelengths on a single strand cable. WDM technology is implemented in couples. One site uses an ADAM-6542/W15 where the transmission channel is 1550nm and the
reception channel is 1310nm. The other site installs an ADAM6542/W13 where the transmission channel is 1310nm and the reception channel is 1550nm. Both the transmission and
reception channels of ADAM-6542/W15 and ADAM-6542/W13 are multiplexed to a single strand cable. This means that cabling costs are halved when you use ADAM-6542/W15 Motion Control
and ADAM-6542/W13 instead of a dual fiber converter.
ADAM-6542 supports MDI/MDIX auto detection, so you don’t need to use crossover wires. It also includes a switch controller that can sense the transmission speed (10/100 Mbps)
ICOM
automatically. Both the Ethernet port and the fiber port have memory buffers that support store-and-forward mechanisms. This assures data can be transmitted properly.
ADAM-6542 is extremely compact and can be mounted in three different ways. DIN rail, panel and piggyback. ADAM-6542 can work normally from -10 to 70°C and accepts a wide
unregulated voltage range from +10 ~ 30 VDC. Besides, it also provides 3,000 VDC surge protection against over-voltage so it is suitable for harsh operating environments.
ADAM-6542 provides three LED indicators: Power, LNK/ACT, and 10/100Mbps, which let you trouble shoot easier.
eConnectivity
Specifications
UNO
System Architecture
Interface: Network
Port
Connector
Compatibility
Surge Protection
Isolation
LED
Transmission Distance
10/100Base-TX & 100Base-FX standard
1 x 10/100 Mbps (RJ-45), 1 x 100 Mbps (Fiber)
1 x RJ-45 & 1 x Fiber (SC type)
IEEE 802.3, IEEE 802.3 u
3,000 VDC (Power)
1,500 Vrms (Ethernet Port)
Power, LNK/ACT, 10/100 Mbps
8.3/125, 8.7/125, 9/125 or 10/125 µm single
Mode fiber, 20 km for WDM (Wavelength Division
Multiplexing)
 Power Requirement
Unregulated 10 ~ 30 VDC
 Power Consumption
3W
 Case
ABS/PC with captive mounting hardware.
 Mounting
DIN-rail, panel mounting, piggyback stack
 Operating Temperature -10 ~ 70° C
 Storage Temperature -20 ~ 80° C
 Operating Humidity
20 ~ 95% (non-condensing)
 Storage Humidity
0 ~ 95% (non-condensing)








ADAM-4000
ADAM-5000
ADAM-6000
ADAM-8000
Ordering Information
 ADAM-6542/W15
 ADAM-6542/W13
10/100Base-TX Ethernet to 100Base-FX WDM Single
Strand Fiber Optic Converter (Tx: 1550nm; Rx: 1310
nm)
10/100Base-TX Ethernet to 100Base-FX WDM Single
Strand Fiber Optic Converter (Tx: 1310 nm; Rx: 1550
nm)
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
BAS
11-17
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-18
EDG-6528
EDG-6528I
8-Port Industrial 10/100 Mbps Ethernet
Switch
8-Port Industrial 10/100 Mbps Ethernet
Switch w/Wide Operating Temperature
Features
NEW
 Provides 8 x 10/100 Mbps Ethernet ports with RJ-45 connector
 Supports full/half duplex flow control
 Supports MDI/MDIX auto crossover
 Provides broadcast storm protection
 Embedded with a switch controller, supports auto-negotiation
 Embedded with the memory buffer, supports store-and-forward transmission
 Supports +12 ~ 48 VDC voltage
 Provides surge protection 3000 VDC for power line
 Supports 4000 VDC Ethernet ESD protection
 Provides flexible mounting: DIN rail and panel-mounting
 Supports wide-range operating temperature: -40 ~ 85° C (EDG-6528I)
 Supports two individual power sources
Introduction
EDG-6528 is an industrial-grade Ethernet switch that realizes fast and cost-effective expansion of industrial networks. EDG-6528 has eight 10/100 Mbps Ethernet ports for connection
with up to eight Ethernet devices. Moreover, EDG-6528 has industrial-grade design that assures high reliability and stability. Therefore, EDG-6528 is an excellent solution for industrial
environments with Ethernet networking, such as semi-conductor factories, inventory control environments, assembly lines and production.
EDG-6528 includes a switch controller that can automatically sense transmission speeds. (10/100 Mbps) The RJ-45 interface can also be auto-detected, so MDI or MDIX is
automatically selected and a cross-over cable is not required. All Ethernet ports have memory buffers that support the store-and-forward mechanism. This assures that data can be
transmitted properly.
The EDG-6528 is extremely compact and can be mounted on a DIN-rail or a panel, so it is suitable for any space-constrained environment. The power line of EDG-6528 supports up
to 3,000 VDC surge protection, which secure equipment against unregulated voltage and make systems safer and more reliable.
For extreme operating temperatures, the EDG-6528I covers a range between -40° and 85° C. With such a wide range you can use the EDG-6528I in some of the harshest industrial
environments that exist.
The LED indicators make troubleshooting quick and easy. Each port has a couple of LEDs that display the link status, power failure, and port activity for immediate on-site
diagnostics.
Specifications












Interfaces
Ports
Connectors
Compatibility
Surge Protection
ESD Protection
LEDs
Transmission Distance
Power Requirement
Case
Mounting
Operating Temperature
 Operating Humidity
Ordering Information
Network 10/100Base-Tx standard
8 x 10/100 Mbps (RJ-45)
8 x RJ-45
1EEE 802.3, IEEE 802.3u
3000 VDC (Power)
4000 VDC (Ethernet)
Power, LINK, 10/100Mbps
100 m (Ethernet)
Unregulated +12 ~ 48 VDC (2 individual power sources)
Aluminum with mounting hardware
DIN-rail, panel
EDG-6528: 0 ~ 70° C
EDG-6528I: -40 ~ 85° C
20~95% (non-condensing)
 EDG-6528
 EDG-6528I
8-Port Industrial 10/100 Mbps Ethernet Switch
8-Port Industrial 10/100 Mbps Ethernet Switch w/wideoperating temperature
eConnectivity Solutions
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
EDG-6528M
EDG-6528S
Industrial Switch with 6 10/100 Mbps
Ethernet Ports & 2 Multi-Mode Fiber Ports
Industrial Switch with 6 10/100 Mbps
Ethernet Ports & 2 Single-Mode Fiber Ports
Features
NEW
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Provides 6 x 10/100 Mbps Ethernet ports with RJ-45 connector
 Provides 2 x 100 Mbps multi-mode (EDG-6528M) / single-mode (EDG6528S) fiber ports
 Supports full/half duplex flow control
 Supports MDI/MDI-X auto crossover
IPPC
TPC
 Provides broadcast storm protection
 Embedded with a switch controller, supports auto-negotiation
 Embedded with the memory buffer, supports store-and-forward transmission
 Supports +12 ~ 48 VDC voltage
 Provides 3000 VDC surge protection for power line
 Supports 4000 VDC Ethernet ESD protection
FPM
ATM & AWS
 Provides flexible mounting: DIN rail and panel-mounting
 Supports two individual power sources
DA&C
Introduction
EDG-6528M and EDG-6528S are industrial-grade Ethernet switches that enable you to expand your industrial network fast and cost-effectively. The EDG-6528M/6528S have six
10/100 Mbps Ethernet ports to connect up to six Ethernet devices. EDG-6528M also provides two multi-mode fiber optic ports, while EDG-6528S provides two single-mode fiber
optic ports with SC-type connectors. Using fiber optics, you can prevent noise from interfering with your system and support high-speed (100 Mbps) and high-distance (up to 2 km)
transmissions. EDG-6528M and EDG-6528S have industrial-grade design that assures high reliability and stability in harsh industrial environments, which makes it a robust bridge
between enterprise fiber backbones and Ethernet devices.
EDG-6528M and EDG-6528S include a switch controller that can automatically sense transmission speeds. (10/100 Mbps) The RJ-45 interface can also be auto-detected, so MDI
or MDI-X is automatically selected and a cross-over cable is not required. All the Ethernet ports have memory buffers that support the store-and-forward mechanism. This assures
that data can be transmitted properly.
EDG-6528M and EDG-6528S are extremely compact and can be mounted on a DIN-rail or a panel. They are suitable for any space-constrained environment.
The power lines of EDG-6528M and EDG-6528S support up to 3,000 V DC surge protection, which secure equipment against unregulated voltage and make systems safer and more
reliable. The operating temperature of EDG-6528M and EDG-6528S is between 0 ~ 70° C. With such a wide range you can use the EDG-6528M and EDG-6528S in some of the
harshest industrial environments that exist.
The LED indicators make troubleshooting quick and easy. Each port has a couple of LEDs that display the link status, power failure, and port activity for immediate on-site
diagnostics.
Specifications
Ordering Information
 Interfaces
 EDG-6528M












Network 10/100Base-Tx standard
100Base-Fx multi-mode standard (EDG-6528M)
100Base-Fx single-mode standard (EDG-6528S)
Ports
6 x 10/100 Mbps (RJ-45)
2 x 100 Mbps (Fiber)
Connectors
6 x RJ-45
2 x Fiber with SC type connector
Compatibility
IEEE 802.3, IEEE 802.3u
Surge Protection
3000 VDC (Power)
ESD Protection
4000 VDC (Ethernet)
LEDs
Power, LINK, 10/100Mbps
Transmission Distance Ethernet
100 m
Multimode fiber
2 Km
Singlemode fiber
15 Km
Power Requirement
Unregulated +12 ~ 48 VDC (2 individual power sources)
Case
Aluminum with mounting hardware
Mounting
DIN-rail, panel
Operating Temperature 0 ~ 70° C (31 ~ 158° F)
Operating Humidity
20 ~ 95% (non-condensing)
 EDG-6528S
ADAM-3000
Motion Control
ICOM
eConnectivity
UNO
Industrial Switch with 6 10/100 Mbps Ethernet Ports &
2 Multi-Mode Fiber Ports
Industrial Switch with 6 10/100 Mbps Ethernet Ports & ADAM-4000
2 Single-Mode Fiber Ports
ADAM-5000
ADAM-6000
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
cPCI
Last updated : January 2005
11-19
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-20
ADAM-4570W
ADAM-4571W
2-port RS-232/422/485 to WLAN
Data Gateway
1-port RS-232/422/485 to WLAN
Data Gateway
Features
NEW
 Supports 802.11b standard
 Supports Wireless LAN Ad-Hoc and Infrastructure modes
 Supports high transmission speeds up to 230 kbps
 Supports an advanced security mechanism to avoid unauthorized access
 Auto-reconnection
 Remote download firmware
 Auto-detecting
 Easy-managing Port Mapping Utility
 Supports Windows® 98/NT/2000/XP driver
 Surge protection for RS-485 line and power supply
 Automatic RS-485 data flow control
Introduction
ADAM-4570W/4571W is a cost-effective data gateway between RS-232/422/485 and 802.11b Wireless LAN interfaces. It provides a quick and low-cost method to connect any RS232/422/485 device to 802.11b wireless LAN. Functionally transparent and efficient, ADAM-4570W and ADAM-4571W saves costs when existing H/W & S/W must continue to be used.
ADAM-4570W and ADAM-4571W bring the advantages of remote management and data accessibility to thousands of RS-232/422/485 devices that cannot connect to the network.
ADAM-4570W and ADAM-4571W provide one or two RS-232/422/485 serial ports, and the transmission speed is up to 230 kbps, meeting the demand for high-speed data exchange.
In addition, you can use a Windows® utility to configure ADAM-4570W and ADAM-4571W without further programming. This not only protects your current hardware investment
but also ensures future network expandability. Since the protocol conversion is transparent, all your existing devices can be seamlessly integrated with the 802.11b wireless LAN
network. Therefore, ADAM-4570W and ADAM-4571W can be used in security systems, factory automation, SCADA, transportation and more.
ADAM-4570W and ADAM-4571W integrate both your existing human-machine interface software (HMI) and the RS-232/422/485 system architecture with an 802.11b Wireless LAN
network. The result helps you save cabling and software development costs. Another benefit is that ADAM-4570W and ADAM-4571W makes it possible to remotely download programs
to a designated device via 802.11b wireless LAN. This reduces the need for on-site maintenance and diagnosis. In addition, ADAM-4570W and ADAM-4571W comes with a Windows
configuration and port-mapping utility. The configuration tool can auto-detect all 802.11b wireless LAN Data Gateway products on the local network. It also lets you adjust all settings
easily. The port mapping utility helps you to set up COM ports for one Windows® NT/2000/XP platform. This helps you configure all ports to meet your requirements.
Specifications
Protocol
Network
Port
Connector
Transmission Speeds
Parity Bits
Data Bits
Stop Bits
Diagnostic LEDs
TCP/IP
802.11b
1/2 Independent RS-232/422/485 ports
Serial: RJ-48 (RJ-48 to DB9 male cable provided)
50 bps ~ 230 kbps
Odd, even, none, space, mark
5, 6, 7, 8
1, 1.5, 2
WLAN: Active, Link
Serial: Tx/Rx
System: Status, Power
 Surge Protection
15 K VESD
 Utility Software
Auto-detecting configuration utility
Port mapping utility
 Driver Support
Windows® 98/NT/2000/XP
 Power Requirement
Unregulated 10 to 30 VDC
 Power Consumption
Max @ 4 Watt
 Mounting
DIN-rail, panel mounting, piggyback stack
 Operating Temperature 0 ~ 60° (32 ~ 140°)
 Storage Temperature -20 ~ 80° (-4 ~ 176°)
 Operating Humidity
20 ~ 95% (non-condensing)
 Storage Humidity
0 ~ 95% (non-condensing)









Ordering Information
 ADAM-4571W
 ADAM-4570W
 OPT1A
 OPT1D
1-port RS-232/422/485 to WLAN Data Gateway
(1 pc of 1 m RJ-48 to male DB9 RS-232/422/485 cable
included)
2-port RS-232/422/485 to WLAN Data Gateway
(2 pcs of 1 m RJ-48 to male DB9 RS-232/422/485
cable included)
1m RJ-48 to male DB9 RS-232/422/485 cable
30cm RJ-48 to male DB9 RS-232/422/485 cable
eConnectivity Solutions
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
WiCOM-3910
Wireless Remote & Monitor
Display Extender
Features
NEW
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Supports 802.11b, 802.11g standard
 Active alarm and record list
IPPC
 Automatic/manual WLAN mode configuring
 High speed wireless presentation
 Supports up to 32-bit color resolution
TPC
 WEP encryption security up to 128 bits
 Robust network security protection
FPM
ATM & AWS
DA&C
Introduction
cPCI
WiCOM-3910 replaces long stretches of VGA cables and KVM switches with its innovative transmission of computer displays over wireless networks.
WiCOM-3910 comes with firmware and a HTTP server to access its settings. It also comes with software that is installed on the computer(s) it will connect with. This software turns
VGA signals into compressed data packets that can be sent over a network, and then uncompressed to be displayed on the screen that is connected to WiCOM-3910. This means the ADAM-3000
refresh rate depends on what is showing on the screen, but in most cases WiCOM-3910 will be able to effectively reproduce a VGA signal at 1024x768.
With two USB V2.0 connectors, a mouse and keyboard can be connected to WiCOM-3910 and used to control remote computers. The USB ports also open up for remote control of
various equipment.
Motion Control
The most appealing application for WiCOM-3910 is probably control of multiple remote computers. With Windows® 2000 or XP installed on the remote computers, WiCOM-3910
can become the interface for several computers over a wireless network. This could for example make inaccessible embedded computers that are distributed in a factory, available
from a protected control room. VGA cables are expensive and cannot be stretched too far, and Cat5 network cables may not be convenient in hazardous environments. WiCOM-3910
ICOM
has WEP 128 bits encryption for security concerns.
Specifications
 Network










Processor System
Memory
Storage
I/O Interface
Miscellaneous
Indicator LEDs
Power Requirement
Dimensions
Support Resolution
Color Depth
eConnectivity
WLAN: 802.11b, 802.11g
LAN: 10/100M Ethernet
SoC Processor
64 MB SDRAM
Flash Memory 8 MB
VGA DB15 x 1, 10/100Base-Tx x 1, USB2.0 x 2
Reset Button, Power Switch, Indicator LEDs
WLAN, LAN, USB, Power
AC/DC power adapter, DC 12V input
180 x 34.5 x 119.3 mm
VGA, SVGA, XGA, SXGA
8/16/24/32 bits
Ordering Information
 WiCOM-3910
Wireless Remote & Monitor Display Extender
ADAM-4000
ADAM-5000
ADAM-6000
PC Requirements (Recommended)
 CPU
 RAM
 Operating Systems
UNO
Intel® Pentium® 500 MHz or above
128 MB recommended
Windows® 2000/XP
ADAM-8000
BAS
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
11-21
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-22
ADAM-6500
ADAM-6501
Web-enabled Communication Controller
Web-enabled Universal Communication
Controller
Features
 Powerful Ethernet-enabled communication controller in a small package
 Built-in Windows CE .NET to run embedded Ethernet applications
 Built-in web server
 Microsoft embedded VC++ development environment supported
 Built-in CompactFlash® slot
 Flash disk for WinCE and user's AP (ADAM-6500: 16 MB, ADAM-6501: 32
MB)
 Built-in real-time clock and watchdog timer
 Offers RS-232 and RS-485 series communication port (ADAM-6500: 3 x
RS-232, 2 x rs-485; ADAM-6501: 1 x RS-232, 1 x RS-485)
 Automatic data flow control in RS-485 mode
 Communication speed up to 115.2 kbps
 Easy to mount on a DIN-rail or panel
Introduction
ADAM-6500 and ADAM-6501 are fully functional Ethernet -enabled controllers for industrial automation and control. They provide an ideal environment to develop applications
converting RS-232/485 devices/equipment data to the Ethernet/Internet world with minimum effort. Their built-in Windows CE .NET operating system lets users run new programs
produced in Microsoft embedded VC++. The Windows environment also includes a web server to allow the designer to develop web-enabled applications.
Specifications
Feature Details
 CPU
















ADAM-6500: 32 bit Intel® StrongArm® 206 MHz
ADAM-6501: 32 bit Intel® XScale® 400 MHz
Flash Memory
16 MB flash memory for ADAM-6500
32MB flash memory for ADAM-6501
Memory
64 MB SDRAM
Operating System
Windows CE .NET
Ethernet Port
ADAM-6500: One 10Base-T
ADAM-6501: One 10/100Base-T
Serial Ports (isolated) ADAM-6500: 3 RS-232, 2 RS-485
ADAM-6501: 1 RS-232 (RJ-48), 1 RS-485
Speed: 115.2 kbps
Built-in Watchdog TimerYes
Real-time Clock
Yes
LED Indicators
Power, diagnostics, communication
Protocols Supported
TCP/IP, UDP
System Management Web-based remote configuration via standard browser
with Java® support.
Console mode command line configuration.
Mounting
DIN-rail, panel, wall, piggyback stack
Default Setting
Onboard
Recovery
Power Supply Voltage +24 VDC (Range: 10 ~ 30 VDC)
Max. Power
+24 VDC @ 0.25 A
Requirements
Operating Temperature 0 ~ 55° C
Storage Temperature -20~ 80° C
Ordering Information
 ADAM-6500
 ADAM-6501
Web-enabled Communication Controller
Web-enabled Communication Controller
Built-in Ethernet and RS-232/485 COM Ports
The ADAM-6500 has one Ethernet (10BASE-T), and four communication ports (3 x RS-232
and 2 x RS-485). The ADAM-6501 has one Ethernet (10/100BASE-T) , one RS-232 and
one RS-232/485 ports. These provide easy communication between the controller and
devices in your applications, and has been designed for program downloading, debugging
and linking serial devices with the Ethernet/Internet. Both ADAM-6500 and 6501 is
equipped with a COM1 port (RS-232) supporting full RS-232 signals for applications
such as modem connections, while the 3-pin RS-232 and RS-485 are designed as the
interface for traditional RS-232/485 devices/equipment. This design allows the controller
to be used in a variety of applications. For example, the user may download a data logging
application into the ADAM-6500/6501’s memory while the ADAM-6500/6501 is connected
to a RS-485 network, and then collect the data over the network.
Built-in Real-time Clock and Watchdog Timer
The real-time clock in the controller ensures accurate time recording when the system
operates. The watchdog timer is designed to automatically reset the CPU if the system
fails.
eConnectivity Solutions
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
ADAM-4500
PC-based Communication Controller
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Powerful communication controller in a small package
 Built-in Boot ROM DOS to run PC programs
IPPC
 Free ROM/RAM memory for user's applications
 2-wire, multi-drop RS-485 networking
 Communication speed up to 115.2 Kbps
TPC
 RS-232/RS-485 modes (jumper selectable)
 Automatic data flow control in RS-485 mode
 Built-in real-time clock and watchdog timer
FPM
 Easy mounting on a DIN-rail or panel
 Accepts unregulated power sources between 10 to 30 VDC
 Program download cable and utility included
ATM & AWS
DA&C
Introduction
The ADAM-4500 is a fully functional stand-alone controller for industrial automation and control. It provides an ideal environment for controlling PC hardware with a minimal amount
of development effort. Its built-in ROM-DOS lets users run standard PC programs or new programs produced by PC language development tools. ROM-DOS is an MS-DOS equivalent
operating system allowing you to run all standard PC software.
cPCI
ADAM-3000
Built-in RS-232/485 COM Ports
The ADAM-4500 has two communication ports (COM1 and COM2). These provide easy communication between the controller and other devices in your applications. COM1 can
be configured for RS-232 or RS-485 communication via a jumper setting, while COM 2 is dedicated as an RS-485 port. This design allows the controller to be used in a variety of Motion Control
applications. For example, a user can download an application into the ADAM-4500's on-board Flash memory while the ADAM-4500 is connected to an RS-485 network, then let it
control all the modules in the network.
Built-in Real-time Clock and Watchdog Timer
ICOM
The real-time clock in the controller ensures accurate time recording while the system operates. The watchdog timer is designed to automatically reset the CPU if the system fails.
Specifications
Board
















CPU
Flash ROM
Operating System
Timer BIOS
SRAM
Real-time Clock
Watchdog Timer
COM1
COM2
Program Download
Port(RS-232)
Power Requirement
Power Consumption
Operating Temperature
Case
Plug-in Screw
Terminal Block
Dimensions
eConnectivity
RS-232 Interface
80188-40
256 KB (170 KB free memory for users)
Boot ROM DOS
Yes
256 KB (234 KB free memory for users)
Yes
Yes
RS-232/485
RS-485
Tx, Rx, GND
Unregulated +10 to +30 VDC
2.0 W
-10 ~ 70° C (14 ~ 158° F)
ABS with captive mounting hardware
Accepts 0.5 mm to 2.5 mm
1-#12 or 2-#14 ~ #22 AWG
60 x 120 mm (2.36" x 4.72")




Signals
Mode
Transmission Speed
Max Transmission
Distance
TxD, RxD, RTS, CTS, DTR, DSR, DCD, RI, GND
asynchronous full duplex, point to point
Up to 115.2 kbps
15.2 meters (50 feet)
ADAM-4000
RS-485 interface




Signals
Mode
Transmission Speed
Max Transmission
Distance
UNO
DATA+, DATA-, GND
Half duplex, multi-drop
Up to 115.2 kbps
1200 meters (4000 feet)
ADAM-5000
ADAM-6000
Software
ADAM-8000
The ADAM-4500 module provides 170 KB ROM for your downloaded applications and
234 KB RAM for application operation. Its built-in ROM-DOS is an MS-DOS equivalent
operating system, which provides all of the basic functions of MS-DOS except BIOS.
Application programs written in high level languages such as C or C++ can run under BAS
ROM-DOS. Application programs should be converted into 80188 compatible code
before being downloaded into the ADAM-4500. The download utility is included with
the ADAM-4500.
Ordering Information
 ADAM-4500
PC-based communication controller
Online Download www.advantech.com/products
All product specifications are subject to change without notice
Last updated : January 2005
11-23
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-24
ADAM-4510/4510S
ADAM-4520/4522
ADAM-4521
Isolated RS-422/485 Repeater
Isolated RS-232 to 422/485 Converter
Addressable RS-422/485 to RS-232
Converter
Features









Automatic RS-485 data flow control
1000 VDC (ADAM-4521)/3000 VDC (ADAM-4510S/4520) isolation protection
Surge protection RS-485 data line
Transmission speed up to 115.2 Kbps
Networking up to 1200 meters (4000 feet)
Reserved space for termination resistors
Power and data flow indicator for troubleshooting
Power requirement: +10 to +30 VDC
Mounts easily on a DIN-rail, panel or piggyback
ADAM-4521 only
 RS-232 and RS-485 can be set to different baud rates
 Watchdog timer function
 Software configurable to either addressable or non-addressable mode
 All communication setups stored in EEPROM
Introduction
Most industrial computer systems come with standard RS-232 serial ports. Though widely accepted, RS-232 has limited transmission speed, range and networking capabilities. The
RS-422 and RS-485 standards overcome these limitations by using differential voltage lines for data and control signals. The ADAM-4520/4522 converter lets you take advantage of
RS-422 and RS-485 on systems originally equipped with RS-232. It transparently converts RS-232 signals into isolated RS-422 or RS-485 signals. You do not need to change your
PC's hardware or your software. The ADAM-4520/4522 lets you easily build an industrial grade, long distance communication system with standard PC hardware.
The ADAM-4521 is an intelligent RS-422/485 to RS-232 converter specifically designed to connect RS-422/485 devices to an RS-232 network. RS-232 is the most common
transmission standard. Although widely available on most computer systems, measurement equipment, PLCs, and industrial devices, its transmission speed, communication distance,
and especially networking capability are limited due to unbalanced transmission. The ADAM-4521 addressable converter solves this problem and lets you easily build up an RS-485
network with your RS-232 devices by assigning each one an address for easier communication.
The ADAM-4510/4510S repeater simply amplifies, or boosts, existing RS-422/485 signals to enable them to cover longer distances. It extends the communication distance by 1200
m (4000 ft.) or increases the maximum number of connected nodes by 32.
Built-in Intelligence
The ADAM-4521 is equipped with a built-in microprocessor, which uses two UARTs and automatically processes data before transmitting it to the RS-232 device. This allows the
ADAM-4521 to handle different baud rates between RS-232 devices and the RS-485 network. The microprocessor also verifies whether the data is transmitted with the appropriate
address, which enables each RS-232 device on the RS-485 network to communicate with your PC over long distances.
An RS-485 Network with Automatic Data Flow Control Using RS-232 Software
The RS-485 standard supports half-duplex communication. This means that a single pair of wires is used to both transmit and receive data. Handshaking signals such as RTS (Request
To Send) are normally used to control the direction of the data flow. A special I/O circuit in the ADAM-4510/4510S/4520/4521/4522 automatically senses the direction of the data flow
and switches the transmission direction. No handshaking signals are necessary—you can build an RS-485 network with just two wires. This RS-485 control is completely transparent
to the user. Software written for half-duplex RS-232 works without modification.
Specifications
ADAM-4520/4521/4522
 Transmission Speed
(bps)
Common
 Power Requirement





Uregulated +10 ~ +30 VDC . Module protected from
power reversals
Case
ABS with captive mounting hardware
Accessories (supplied) ABS DIN-rail mounting adapter,
Nylon DIN-rail mounting adapter (ADAM-4521 only)
SECC panel mounting bracket
Plug-in Screw
Accepts AWG 1- #12 or
2- #14 ~ #22 (0.5 to 2.5 mm2) wires
Terminal Wiring
Operating Temperature -10 ~ 70° C (14 ~ 158° F)
Dimensions
60 x 120 mm (2.36" x 4.41")
ADAM-4510/4510S
 Transmission Speeds
(bps)
 Isolation Voltage
 RS-422/RS-485
Interface Connector
 Power Consumption
1200, 2400, 4800, 9600,
19.2 k, 38.4 k, 57.6 k, 115.2 k (switchable)
3000 VDC (ADAM-4510S only)
Plug-in screw terminal
1.4 W @ 24 VDC
 Isolation Voltage
 RS-232 Interface
Connector
 RS-422/RS-485
Interface Connector
 Power Consumption
300, 600 (ADAM-4521 only), 1200, 2400, 4800, 9600,
19.2 k, 38.4 k, 57.6 k 115.2 k, RTS control and RS422 mode (switchable)
3000 VDC (ADAM-4520 only)
Female DB9
Plug-in screw terminal
1.2 W (ADAM-4520/4522)
1 W @ 24 VDC (ADAM-4521)
Ordering Information





ADAM-4510
ADAM-4510S
ADAM-4520
ADAM-4522
ADAM-4521
RS-422/RS-485 repeater
Isolated RS-422/RS-485 repeater
Isolated RS-232 to RS-422/485 converter
RS-232 to RS-422/485 converter
Addressable RS-422/485 to RS-232 Converter with
1000 VDC Isolation
eConnectivity Solutions
All product specifications are subject to change without notice
Last updated : January 2005
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
ADAM-4541
ADAM-4542+
Multi-Mode Fiber-Optic to RS-232/422/485
Converter
Single-Mode Fiber-Optic to RS-232/422/485
Converter
Features
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Software
 Easily mounted on a DIN-rail, panel or piggyback
 Transmission speeds of up to 115.2 kbps
 Optical fibers enable transmission of 2.5 km (measured with 62.5/125 mm) for
ADAM-4541
 Half/Full-duplex, bidirectional transmission mode
 Avoids lightning strikes and EMI/RFI interference
 Prevents damage from electrostatic discharge
 Stable and error-free data transmission
 Automatic internal RS-485 bus supervision
 No external flow control signals required for RS-485
 Transient suppression and over-current protection on RS-422/485 data lines
 Reserved space for termination resistors
 LED for power and data flow indication
 Power requirement: +10 to + 30 VDC
IPPC
TPC
FPM
ATM & AWS
DA&C
Introduction
Fiber-optic transmission offers the benefits of wide bandwidth, immunity to EMI/RFI interference, and secure data transmission. ADAM-4541 and ADAM-4542+ can be used as an
RS-232/422/485 point-to-point or point-to-multipoint connection for transmitting and converting full/half-duplex signals and their equivalents within a fiber optic environment. Fiber
optics is the perfect solution for applications where the transmission medium must be protected from electrical exposure, lightning, atmospheric conditions or chemical corrosion.
ADAM-4541 and ADAM-4542+ is specifically designed to link various machinery equipped with an RS-232/422/485 communication ports (such as computer systems or manufacturing
machines). Using standard ST connectors, the module's fiber-optic ports can accommodate a wide range of fiber-optic cable sizes, including 62.5/125, 250/125, and 100/140 mm.
cPCI
ADAM-3000
Motion Control
Specifications








Casing
Communication Mode
Connector
Transmission Mode
Transmission Rate
Operating Temperature
Operating Humidity
Accessories (included)
Ordering Information
ABS with captive mounting hardware
Asynchronous
Plug-in screw terminal
Full/half-duplex, bidirectional
Up to 115. 2 kbps
-10 ~ 70° C (14 ~ 158° F)
5 ~ 95% (non-condensing)
Nylon DIN-rail mounting adapter, SECC panel
mounting bracket
ADAM-4541
 Fiber Port
 Fiber-Optic Transfer
Mode
 Wavelength
 Transmission Distance
 Optical Power Budget
(attenuation)
 Power Consumption
ST
Multi-mode
820 nm
2.5 km
12.5 dB
1 W (typical)
1 W (max.)
 ADAM-4542+
Multi-Mode Fiber-Optic to RS-232/422/485
converter
Single-mode Fiber-Optic to RS-232/422/485 Converter
Advantages of Fiber Optics




SC
Single mode
1310 nm
15 km
9 dB
1 W (typical), 1.5 W (max)
Low signal radiation
Secure transmission
Lightning immunity
High-voltage insulation
eConnectivity
ADAM-4000
ADAM-5000
Compact
 Less duct space
 Fewer additional ducts installed
ADAM-6000
Low Attenuation
 Greater distance / fewer repeaters
 Less installation and maintenance
ADAM-8000
 No ground loops
 No spark hazard
 Operation in flammable areas
BAS
High Bandwidth
 Future signal capacity expansion
Online Download www.advantech.com/products
All product specifications are subject to change without notice
ICOM
UNO
All Dielectric
Optical Signals
ADAM-4542+
 Fiber Port
 Fiber-Optic Transfer
Mode
 Wavelength
 Transmission Distance
 Optical Power Budget
 Power Consumption
 ADAM-4541
Last updated : January 2005
11-25
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: (650) 588-9200-Outside Local Area: (800) 258-9200-www.stevenengineering.com
11-26
ADAM-4561
1-port Isolated USB to
RS-232/422/485 Converter
Features
 Full compliance with USB V1.1 specifications.
 RS-232/422/485 port supported
 Transmission speed up to 115.2 kbps
 Isolation protection 3000 VDC provided
 Automatic RS-485 data flow control
 No external power supply necessary; the hub derives its power from the USB
port.
 Plug & Play installation.
 No additional IRQs or I/O ports required.
 Hot attach & detach function supported
Introduction
ADAM-4561 allows PC users to connect a serial device to a system that use a USB interface. To attach the ADAM-4561 to a PC, you don’t need to open the chassis or power down
your PC. Instantly get one or two extra high-speed RS-232/422/485 ports. The power is derived from the USB port, so there are no power adapters to deal with. This makes the
ADAM-4561 especially suitable for modems, printers, POS systems and industrial control devices.
Compliant with USB V1.1, ADAM-4561 features several powerful functions such as high-speed 115.2 kbps transmission, support for various operating systems, independent RS232/422/485 ports and more. By simply plugging in a USB hub, ADAM-4561 eliminates the configuration issues associated with high-priced, older card solutions. You only have to
install the drivers, no need to set cards slots, IRQ addresses, DMA channels, or device addresses. This reduces programming effort.
USB, now standard on virtually all new PCs, offers significant advantages over earlier bus types. A single USB interface can connect up to 127 devices at data rates up to 12 Mbps.
That kind of easy and convenient connectivity means that your network can grow with your requirements.
Specifications
Ordering Information
 Compatibility
 Interface
 ADAM-4561
USB v1.1 standard
Network: USB
Serial: 3-wire RS-232, RS-422, RS-485
 Ports
1 x RS-232/422/485
 Connector
Network: USB type A connector (Type A to Type B
cable provided)
Serial: twist-wire
 Transmission Speed
50 bps to 115.2 kbps
 Parity Bits
Odd, even, none
 Data Bits
5, 6, 7, 8
 Stop Bits
1, 1.5, 2
 RS-232 Signals
Tx, Rx, GND
 Surge Protection
3000 VDC (RS-485)
 Isolation Protection
3000 VDC (RS-232/422/485)
 Driver Supported
Windows® 98/2000/ME/XP, Linux®
 Power Consumption
270 mA @ 5 V (Typical)
300 mA @ 5 V (Max.)
 Max. Distance
15 ft (4.6m)
 Case
ABS with captive mounting hardware
 Mounting
DIN-rail, panel mounting, piggyback stack
 Operating Temperature 0 ~ 70° C (32 ~ 158° F)
 Storage Temperature -25 ~ 80° C (-13 ~ 176° F)
 Operating Humidity
20 ~ 95% (non-condensing)
 Storage Humidity
0 ~ 95% (non-condensing)
1-port Isolated USB to RS-232/422/485 Converter
eConnectivity Solutions
All product specifications are subject to change without notice
Last updated : January 2005
Download PDF