CiA | TVCD606 | Technical data | CiA TVCD606 Technical data

Installation and Operation Manual
for
TVCD606
Please read the operation manual carefully
before installing and using this unit
2
I. Points for Attention
1. Before installing the omni bearing intelligent unit, please read the operation
manual carefully.
2. The camera takes power supply of DC12V/1.2A. You should assure that the power
supply of the product has an input voltage with load about 12V rather than a
unload voltage of 12V, otherwise the camera couldn’t work normally.
3. During the process of transportation, storage and installation, the dome should be
avoided of incorrect operations such as heavy pressing, strong vibration etc. which
can cause damage of product as there are sophisticated optical and electronic
devices inside the machine.
4. Do not attempt to disassemble the camera. In order to prevent electric shock, do
not remove screws or covers. There are no user serviceable parts inside and only
qualified personnel are to service the unit
5.
Always follow all electrical standards for safety when it is in operation. Adopt the
particular power supply, which is provided with the dome. RS-485 and video
signal should keep enough distance with high voltage equipments and cables
when they are in transmission. Precautions for anti-lightning and anti-surging
should be taken if necessary.
6. The product should be indoor installed and operated to avoid rain and moisture. Do not use it
in wet places. If outdoor installation is needed, the closed protect cover should be used and it
is absolutely prohibited to use it in open air independently.
7.
Do not operate it in case temperature, humidity and power supply are beyond the
limited stipulations.
8.Do not let the video camera aim at the sun or the object with extreme light
whatsoever it is switched on or not. Do not let the video camera aim at or monitor
bright and standstill object for a long time.
9. Do not use aggressive detergent to clean the main body of the video camera.
Wipe dirt with dry cloth. If needed, mild detergent can be used suitably.
10. Operate the intelligent high-speed spherical video camera with great care to
avoid shock or vibration. It operate incorrectly, machine could be damaged.
11. Install the video camera in the place where endurance should be enough large.
12. Should be dust on the lens, you should wipe it with special lens tissue.
1
II. Description of Functions
The dome camera is a hi-tech CCTV product, which incorporates color TV, omni
bearing dome P/T and multifunctional decoder into a whole. It can largely reduce
connection and installation processes of components in the system, rise up reliability
of the system and facilitate installation and maintenance. Therefore it has advantages
of beautiful appearance, compact structure and easy operation.
1. Integrated Multi-Protocol Decoder
a. With built-up decoder and integrated multi-protocol, it can integrate 16 kinds
of communication protocols in maximum. As its baud rate of communication
can be adjusted, it is compatible with main domestic and foreign systems by
easy setting inside the spherical camera, so it has stronger versatility.
b. RS485 serial control: addresses of the dome camera 1-1023.
2. Integrated Omni bearing dome P/T
a. Turning 360º horizontally and continuously with unlimited positions. PAN
speed range:0~15rad/s (constant speed dome PAN: 15rad/s); turning 0~90º
vertically with a speed 0~15rad /s(constant speed dome TILT: 15rad/s).
b. Running stably at low speed with super lower noise. Pictures have no
shaking.
c. the location precision up to ±0.2°.
3. High Intelligent Degree
a.
Support the dome camera to scan horizontally between two points and scan
speed can be modified.
b. Data can be stored with powerless memory.
4. Newly-Added Functions
a.
5.
Flexible and Convenient Application: there are many communication
protocols integrated inside the spherical camera and the baud rates can be
selected from 24000 bps to 19200 bps.
Selectable Optical Zoom Range of Camera
Times of Optical
Zooming
Focus Range
Lowest Illuminance
16x
f3.9-f6.3 mm
1 Lux (F1.4)
18x
f4.1-f73.8 mm
1 Lux (common type) / 0.01 Lux(day & night type)
22x
f4-f88 mm
0.2 Lux(F1.6 1/3s)
23x
f3.6-f82.8 mm
1 Lux (Common type) / 0.01 Lux(day & night type)
25x
f3.6-f90 mm
1 Lux (Common type) / 0.01 Lux(day & night type)
2
III. Settings of Special Camera
Before installing the spherical camera, please confirm the communication protocol
and baud rate the master controler in the system uses, then set the coding switches on
the back of the camera to be identical with that of the system in which SW1 is for
address of the spherical camera and SW2 is for communication protocol and baud rate
(see attached tables 1,2 and 3).
SW1
SW2
ON
ON
1
2
3
4
5
6
Pr ot ocol Sel ect
1
2
3
4
5
6 7
8
9 10
Speed Dome Addr ess Sel ect
1 2 3
I D- CODE Set
JP
120Ω terminal resistor is opened for RS485 bus
1 2 3
Syst em
cont r ol wi r e
JP
120Ω terminal resistor is connected on RS485 Bus
JP1 is jumper for the terminal resistor
JP1 is the 120 Ω terminal resistor for RS485 Bus. When short-circuit terminal is set between
“1-2”, the 120 Ω terminal resistor is opened while it is set between “2-3”, the resistor is
connected. Take care that on RS 485 Bus only one farthest spherical camera has the terminal
resistor connected while other devices should have their terminal resistors opened.
z Settings of Addresses of dome Cameras
Dome
Addres
s
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
…
1023
3
States of Coding Switches
DIP1
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
…
ON
DIP2
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
…
ON
DIP3
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
…
ON
DIP4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
…
ON
DIP5
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
…
ON
DIP6
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
…
ON
DIP7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
…
ON
DIP8
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
…
ON
DIP9
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
…
ON
DIP-1
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
…
ON
Table 1
For Example:
ON
ON
1
2
3
4
5
6 7
8
9 10
ON
1
2
3
4
5
6 7
8
9 10
1
2
3
4
5
6 7
8
9 10
Speed Dome Addr ess=1
Speed Dome Addr ess=2
Speed Dome Addr ess=3
ON
ON
ON
1
2
3
4
5
6 7
8
9 10
Speed Dome Addr ess=4
1
2
3
4
5
6 7
8
9 10
1
Speed Dome Addr ess=18
2
3
4
5
6 7
8
9 10
Speed Dome Addr ess=1023
Notes:
1. Addresses of the dome cameras are denoted by binary code system. ON means
“1” while OFF means “0”.
2. Above coded addresses are only from no.1 to no.20. The codes of addresses from
no.21 to no.1023 can be deduced by analogue.
3. The range of addresses of the spherical cameras is from 1 to 1023.
z
Settings of communication protocol of the dome camera (DIP1-DIP4 of SW2)
and its default baud rate (DIP5-DIP6 of SW2). In case the default baud rate of the
dome camera is not in accordance with that of the controller, please reset it as per
the Table 3 (● means the protocol has been done).
Type of Protocols
Minking A01
Minking B01
Santachi
PELCO-D
PELCO-P/4800
PELCO-P/9600
PANASONIC
Longcomity
HUNDA600
LILIN
VICON
MOLYNX
KALATEL
VCL
DAIWA
ALEC
Utralk
Selection of Protocols
Normal Baud Rate
DIP-1
OFF
ON
OFF
ON
DIP-2
OFF
OFF
ON
ON
DIP-3
OFF
OFF
OFF
OFF
DIP-4
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
DIP-5
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
DIP-6
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
ON
Integrated
Protocol
●
●
●
●
●
○
●
●
○
○
○
○
○
○
○
○
Table 2
Protocols mentioned above are suitable for the dome camera. Among them “Santachi”,
“ PELCO-D” and “PELCO-P” have no corresponding orders for some special
functions in the protocols. In order to control some special functions of the spherical
camera, we make some functional transformation upon some common orders.
Normally we take “Call Preset Position / Set Preset position” to transform, and
contents of order transformation are listed below.
4
Number
Control Object
of N
Value
51
Supplementary Control of
52
dome
53
Power Supply of Camera
54
Definition of Keypad Operation
Call No. N Preset Point
Start Scan (low Speed)
Start Scan (middle Speed)
Start Scan (high Speed)
Power Supply On
Set No. N Preset Point
Start Patrol
Set Start Position of Scan
Set End Position of Scan
Power Supply Off
55
56
BLC
On
Off
Zero Illuminance
On
Off
57
Screen Display *
On
Off
58
D-Zoom
On
Off
59
Focus
Automatic
Manual
60
Iris
Automatic
Manual
Automatic
Manual
Interior
Exterior
ATW
One Push WB
61
62
Mode of White Balance *
63
64
Notes:
1. Those Items with “*” have memory function even the dome is switched off.
2. For those cameras with “menu”, you can use “Screen Display ON” to control the
Menu ON/OFF, and use “Screen Display OFF” to control Screen Display
ON/OFF.
3. For those cameras which have no “Zero Illuminance” or the function of “Zero
Illuminance” is automatically switched without control, then above “Zero
Illuminance” is invalid.
4. Notes to “Patrol” Function of the dome camera:
① Automatically scan from no.1 to no.16 preset points one by one. If some
points do not have been preset or are cleared out after presetting, they will be
bypassed when patrol is carrying out.
② The dwelling time between to preset points is 4 seconds.
③ The “Patrol” function of the dome camera can be carried out by presetting
no.51 position.
5. Notes to “Scan(auto pan)” Function of the dome camera:
① The dome camera makes automatic scan between two specified positions.
② The speeds of scan are divided into three levels. You can call no. 51, 52 and
53 preset position to start scan at speed of 1.5°/ sec, 5°/ sec and 10°/ sec
separately.
③ The dwelling time between the “Start Point” and “End Point” of scan is 3
seconds.
6. All notes mentioned above are supplementary descriptions under high speed. All original
operations of the control system are unchanged.
z
5
Settings of Communication Baud Rate of the dome Camera
Coding Switch
Baud Rate
2400 bps
4800 bps
9600 bps
19200 bps
1
2
3
4
5
OFF
ON
OFF
ON
6
OFF
OFF
ON
ON
IV. Steps of Installation
1. Mounting Base
2.
3.
4.
5.
6.
Outer Tube
Shading Cover
Outer Cover
Camera
Connecting Cable
Dimension Drawing
1. Carefully read the operation manual and the points for attention.
2. Carefully set the communication code, baud rate and address of the dome camera
and make confirmation they are correct.
3. Take out the plug of the dome camera and connect external power supply, RS485
and video wires as per marks on the plug. Take care that the power supply of the
dome camera is DC12V/1.2A and adopt the particular power supply which is
provided with the dome camera.
Red : DC12V+
Black : GND
Orange : RS485+
Yellow: RS485VIDEO
.
4.
Take out the mounting base from the spherical camera, thread the connecting
wire from behind through the central hole of the base. Fix the base by three
screws on the ceiling as per the drawing, and connect the wire with the ball. Aim
the latch in the ball with the notch on the base as per the drawing, and mount the
ball upward to the position and turn it clockwise until the spring sheet on the
base takes effect. In case the wire could not come out from behind the ceiling,
you can open a hole on the edge of the casing for running of the wire.
6
Installation Drawing
V.
Main Technical Data
Specifications
Camera Function
Lens Data
7
Image
Inductor
Effective
Pixels
Synchronous
System
VF Output
White Balance
Power Supply
Power
Consumption
Weight
Mounting
Style
Relative
humidity
Operation
Temperature
Scan System
Horizontal
Resolution
Signal / Noise
ratio
Electronic
Shutter
Lowest
Temperature
Zooming
Range
1/4″Color CCD
752H×582V(440000pixels)
Internal Synchronization
Compound Signal 1.0Vp-p/75Ω
Automatic/Manual
DC12V±10% 1.2A
12VA
2Kg
Ceiling or ceiling hanging style
10-75%(under no condensing)
0℃~40℃
15.625KHz(H) 50Hz (V)
480 TV lines
Larger than 48 db
1/3~1/10000 seconds
1Lux,AGC ON
18×Optical and 12×Digital
PAL
Basic Functions
of Spherical
Camera
Iris
Focus
Horizontal
Turning
Vertical
Turning
Preset
Positions
Patrol
Function
Automatic/Manual
Automatic/Manual
0--15°/s (constant P/T: 15°/s fixed)
0--15°/s (constant P/T: 15°/s fixed)
64 presets (max)
At best 6 cruises
VI. Analysis of Normal Troubles
Problems
No action and images when
power is switched on
Abnormal self-inspection.
Images with roaring sound of
the motor
Normal self-inspection but no
images
Successful self-inspection but
out of control
Possible Causes
Power supply damaged or
insufficient power
Wrong connection of power
supply
Faults in engineering circuits
Mechanical fault
Tilting camera
Insufficient electrical power
Wrong connection of VF
circuit
Bad connection of VF circuit
Camera damaged
Wrong connection of control
signal wire
Mismatched address of
spherical camera
Mismatched protocol
Images unstable
Bad connection of VF circuit
Insufficient electrical power
Abnormal self-inspection
Bad connection of control wire
Problems on main frame
Dome Camera out of control
Too heavy load or longer
distance of communication
Remedies
Replace
Correct
Remove
Repair
Place uprightly
Replace with qualified power
supply and let it close to the
spherical camera
Correct
Remove
Replace
Correct
Reselect
Adjust protocol to match with
the controller and switch on
again
Remove
Replace
Switch on again
Remove
Switch on the main frame
1. Connect 120Ω resistor to
the farthest camera and let
other cameras to be
broken;
2. Increase code distributor.
Normal problems and their causes and remedies mentioned above are only for
reference. Should you meet other special problems, you can ask for technical
support from your dealer directly.
8
Download PDF