APC | Network Management Card | Installation manual | APC Network Management Card Installation manual

Installation
Manual
Network
Management
Card
AP9635
Dieses Handbuch ist in Deutsch auf der APC Webseite (www.apc.com)
verfügbar.
Deze handleiding is beschikbaar in het Nederlands op de APC Website
(www.apc.com).
Este manual está disponible en español en la página web de APC
(www.apc.com).
Ce manuel est disponible en français sur le site internet d’APC
(www.apc.com).
Questo manuale è disponibile in italiano sul sito web di APC
(www.apc.com).
本マニュアル<各国の言語に対応する>は APC ウェブサイト
(www.apc.com) からダウンロードできます。
Este manual está disponível em português no site da APC
(www.apc.com).
Данное руководство на русском языке доступно на сайте APC
(www.apc.com )
在 APC 公司的网站上 (www.apc.com) 有本手册的中文版。
Contents
Preliminary Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Related documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Please recycle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
Installation in a Symmetra PX UPS. . . . . . . . . . . . . . . . . . . . . . . . 3
Quick Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TCP/IP configuration methods . . . . . . . . . . . . . . . . . . . . . 4
APC Device IP Configuration Wizard . . . . . . . . . . . . . . .
5
.ini file utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
BOOTP and DHCP configuration . . . . . . . . . . . . . . . . . .
5
Local access to the command line interface . . . . . . . . . .
8
Remote access to the command line interface . . . . . . . .
8
Command line interface . . . . . . . . . . . . . . . . . . . . . . . . .
9
User interface display (Symmetra PX 250
or Symmetra PX 500 UPS) . . . . . . . . . . . . . . . . . . . . . . 10
How to Recover from a Lost Password . . . . . . . . . . . . . . . . . . . 11
How to Access a Configured Network Management Card . . . . 12
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
Web interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
Telnet and SSH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Simple Network Management Protocol (SNMP)
. . . . . . 13
FTP and SCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
Manage the security of your system . . . . . . . . . . . . . . .
15
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Installation Manual
i
Preliminary Information
Features
The American Power Conversion (APC®) Network Management Card has
standard features that do the following:
• Detect 10/100 Mbps connection speeds
• Provide a data log accessible by File Transfer Protocol (FTP), Secure
CoPy (SCP), or a Web browser
• Provide an event log that is accessible by Telnet, Secure SHell (SSH),
FTP, SCP, or a Web browser
• Generate system log (Syslog) messages
• Enable you to configure a BOOTstrap Protocol (BOOTP) or Dynamic
Host Configuration Protocol (DHCP) server to provide the TCP/IP
values a Network Management Card needs for network communication
• Generate e-mail notifications for UPS or system events
• Limit SNMP traps, e-mail notification, and event logging based on
severity and categories of events
• Enable you to configure multiple Network Management Cards
simultaneously over the network
• Provide enhanced security by supporting SSH, Secure Sockets Layer
(SSL) and Secure CoPy (SCP)
Related documents
The APC Network Management Card Utility CD contains the following
documentation:
• Network Management Card User’s Guide
• Network Management Card Upgrade Utilities
• Security Handbook
• PowerNet® Management Information Base (MIB) Reference Guide
Installation Manual
1
Inventory
The Network Management Card package includes the following items:
• This Installation Manual
• Network Management Card
• APC Network Management Card Utility CD
• Serial configuration cable (940-0299)
• Network Management Card quality assurance test slip
• Declaration of Conformity
• Warranty registration form
Save the quality assurance test slip. The slip contains the MAC
address that you may need when performing the procedures in
“TCP/IP configuration methods” on page 4.
Disclaimer
American Power Conversion is not responsible for damage sustained during
reshipment of this product.
The Network Management Card is sensitive to static electricity.
When handling the Management Card, touch only the end plate
while using one or more of these electrostatic-discharge devices
(ESDs): wrist straps, heel straps, toe straps, or conductive shoes.
Please recycle
The shipping materials are recyclable. Save them for later use, or
dispose of them appropriately.
APC management products, including the Network Management
Card, contain removable, lithium coin-cell batteries. When
discarding these batteries, you must follow local rules for
recycling.
2
Installation Manual
Installation in a Symmetra PX UPS
You do not need to turn off the power for a Symmetra PX 250 or Symmetra PX
500 UPS before you remove or install the Management Card.
The Network Management Card is sensitive to static electricity.
When handling the Management Card, touch only the end plate
while using one or more of these electrostatic-discharge devices
(ESDs): wrist straps, heel straps, toe straps, or conductive shoes.
For the location of the UPS card slot, see the UPS documentation.
1.
Locate the UPS card slot.
2. Use the same screws that hold the slot cover in place to secure the
Management Card in the UPS card slot.
3. Connect a network interface cable to the 10/100Base-T network
connector  on the Management Card.
Config
Universal I/O Modem
Smart Slot
Modbus
TXD
1
Ch
Gnd
0
1
RXD
Com
0
Netw or k
Reset
10/100
AP9635 Network Manage ment Card 2
Installation Manual
dmp0096a
USB
3
Quick Configuration
Overview
Note: Disregard the procedures described in this chapter if you
have APC InfraStruXure® Central as part of your system. See the
documentation for your InfraStruXure device for more information.
You must configure the following TCP/IP settings before the Network
Management Card can operate on a network:
• IP address of the Network Management Card
• Subnet mask
• Default gateway
Note: If a default gateway is unavailable, use the IP address of a
computer that is located on the same subnet as the Network
Management Card and that is usually running. The Network
Management Card uses the default gateway to test the network
when traffic is very light.
Caution: Do not use the loopback address (127.0.0.1) as the
default gateway address for the Network Management Card. It
disables the card and requires you to reset TCP/IP settings to their
defaults using a local serial login.
See “Watchdog Features” in the “Introduction” of the Network
Management Card User’s Guide for more information about the
watchdog role of the default gateway.
TCP/IP configuration methods
Use one of the following methods to define the TCP/IP settings needed by the
Network Management Card:
• APC Device IP Configuration Wizard (See “APC Device IP
Configuration Wizard” on page 5.)
• BOOTP or DHCP server (See “BOOTP and DHCP configuration” on
page 5.)
• Networked computer (See “Local access to the command line interface”
on page 8 or “Remote access to the command line interface” on page 8.)
• Symmetra PX 250 or Symmetra PX 500 user interface display (See
“User interface display (Symmetra PX 250 or Symmetra PX 500 UPS)”
on page 10.)
4
Installation Manual
APC Device IP Configuration Wizard
You can use the APC Device IP Configuration Wizard at a computer running
Microsoft® Windows® 2000, Windows Server® 2003, or Windows XP to
discover unconfigured Network Management Cards and configure their basic
TCP/IP settings, one card at a time, over the network.
Note: Most software firewalls must be temporarily disabled for the
Wizard to discover unconfigured Network Management Cards.
1. If autorun is enabled, the user interface of the CD starts when you
insert the APC Network Management Card Utility CD into a computer
on your network. Otherwise, open the file contents.htm on the CD.
2.
Select the Device IP Configuration Wizard from the main menu.
3. When the Wizard discovers the unconfigured Network Management
Card, follow the on-screen instructions.
Note: If you leave the option Start a Web browser when finished
enabled, you can access the Network Management Card through
your browser by using apc (the default) for both the user name and
password.
.ini file utility
You can use the .ini file export utility to export .ini file settings from configured
Network Management Cards to one or more unconfigured Network
Management Cards. The utility and documentation are included on the APC
Network Management Card Utility CD.
BOOTP and DHCP configuration
The default TCP/IP configuration setting, BOOTP & DHCP, assumes that a
properly configured BOOTP or DHCP server is available to provide TCP/IP
settings to Network Management Cards. The Network Management Card first
attempts to discover a properly configured BOOTP server, and then a DHCP
server. It repeats this pattern until it discovers a BOOTP or DHCP server.
A user configuration (.ini) file can function as a BOOTP or DHCP
boot file. For more information, see the TCP/IP configuration
section of the Network Management Card User’s Guide, available
from the Utility CD or the APC Web site, www.apc.com.
Installation Manual
5
If neither of these servers is available, see one of these sections to
configure the needed TCP/IP settings:
• “APC Device IP Configuration Wizard” on page 5
• “Local access to the command line interface” on page 8
• “Remote access to the command line interface” on page 8
• “User interface display (Symmetra PX 250 or Symmetra PX 500
UPS)” on page 10.
BOOTP. For the Network Management Card to use a BOOTP server to
configure its TCP/IP settings, it must find a properly configured
RFC951-compliant BOOTP server.
In the BOOTPTAB file of the BOOTP server, enter the Network Management
Card’s MAC address, IP address, subnet mask, and default gateway, and,
optionally, a bootup file name. Look for the MAC address on the bottom of the
Network Management Card or on the Quality Assurance slip included in the
package.
When the Network Management Card reboots, the BOOTP server provides it
with the TCP/IP settings.
• If you specified a bootup file name, the Network Management Card
attempts to transfer that file from the BOOTP server using TFTP or FTP.
The Network Management Card assumes all settings specified in the
bootup file.
• If you did not specify a bootup file name, you can configure the other
settings of the Network Management Card remotely through its Web
interface or command line interface; the user name and password are
both apc, by default.
To create a bootup file, see your BOOTP server documentation.
6
Installation Manual
DHCP. You can use an RFC2131/RFC2132-compliant DHCP server to
configure the TCP/IP settings for the Network Management Card.
This section summarizes the Network Management Card’s
communication with a DHCP server. For more detail about how a
DHCP server can configure the network settings for a Network
Management Card, see “DHCP Configuration” in the Network
Management Card User’s Guide on the Utility CD.
1. The Network Management Card sends out a DHCP request that uses
the following to identify itself:
– A Vendor Class Identifier (APC by default)
– A Client Identifier (by default, the MAC address of the Network
Management Card)
– A User Class Identifier (by default, the identification of the
application firmware installed on the Network Management Card)
2. A properly configured DHCP server responds with a DHCP offer that
includes all the settings that the Network Management Card needs for
network communication. The DHCP offer also includes the Vendor
Specific Information option (DHCP option 43). By default, the
Network Management Card ignores DHCP offers that do not
encapsulate the APC cookie in DHCP option 43 using the following
hexadecimal format:
Option 43 = 01 04 31 41 50 43
where
– the first byte (01) is the code
– the second byte (04) is the length
– the remaining bytes (31 41 50 43) are the APC cookie.
See your DHCP server documentation to add code to the Vendor
Specific Information option.
Note: To disable the requirement that a DHCP offer include the
APC cookie, clear the check box Require vendor specific cookie to
accept DHCP Address in the Web interface: Administration >
Network>TCP/IP>DHCP.
Alternately, at the command line interface, use this command to
disable the DHCP cookie requirement : boot -c disable
Installation Manual
7
Local access to the command line interface
You can use a computer connected to the serial port on the front of the Network
Management Card to access the command line interface.
1. Select a serial port at the local computer, and disable any service that
uses that port.
2. Use the provided serial cable (APC part number 940-0299) to connect
the selected port to the serial port on the front panel of the Network
Management Card.
3. Run a terminal program (such as HyperTerminal) and configure the
selected port for 9600 bps, 8 data bits, no parity, 1 stop bit, and no flow
control. Save the changes.
4. Press ENTER, repeatedly if necessary, to display the User Name
prompt.
5.
Use apc for the user name and password.
See “Command line interface” on page 9 to finish the
configuration.
Remote access to the command line interface
From any computer on the same network as the Network Management Card,
you can use ARP and Ping to assign an IP address to the Network Management
Card, and then use Telnet to access its command line interface and configure
the other TCP/IP settings.
Note: After the Network Management Card has its IP address
configured, you can use Telnet, without first using ARP and Ping, to
access that Network Management Card.
1. Use the MAC address of the Network Management Card in the ARP
command to define the IP address.
Note: Look for the MAC address on the bottom of the
Network Management Card or on the Quality Assurance
slip included in the package.
For example, to define 156.205.14.141 as the IP address of a Network
Management Card with 00 c0 b7 63 9f 67 as its MAC address, use one
of the following commands:
– Windows command format:
arp -s 156.205.14.141 00-c0-b7-63-9f-67
– LINUX command format:
arp -s 156.205.14.141 00:c0:b7:63:9f:67
8
Installation Manual
2. Use Ping with a size of 113 bytes to assign the IP address defined by
the ARP command. For the IP address defined in step 1, use one of the
following commands:
– Windows command format:
ping 156.205.14.141 -l 113
– LINUX command format:
ping 156.205.14.141 -s 113
3. Use Telnet to access the Network Management Card at its newly
assigned IP address. For example:
telnet 156.205.14.141
4.
Use apc for both user name and password.
See “Command line interface” on this page to finish the
configuration.
Command line interface
After you log on at the command line interface, as described in “Local access to
the command line interface” on page 8 or “Remote access to the command line
interface” on page 8, you can manually configure network settings.
1. Contact your network administrator to obtain the IP address, subnet
mask, and default gateway for the Network Management Card.
2. Use these three commands to configure network settings. (Text in
italics indicates a variable.)
a. tcpip -i yourIPaddress
b. tcpip -s yourSubnetMask
c. tcpip -g yourDefaultGateway
For each variable, type a numeric value that has the format
xxx.xxx.xxx.xxx.
For example, to set a system IP address of 156.205.14.141, type
the following command and press ENTER:
tcpip -i 156.205.14.141
3. Type exit. The Network Management Card restarts to apply the
changes.
Installation Manual
9
User interface display (Symmetra PX 250 or Symmetra PX 500 UPS)
To configure the IP address of a Network Management Card at the user
interface display of the Symmetra PX UPS:
1. If you plan to manually assign the network settings, contact your
system administrator to obtain a valid IP address, subnet mask, and
default gateway for the Network Management Card.
2. At the user interface display, press the UPS System icon.
3. Select Configuration, then User Configuration.
4. At the prompt, enter the user password for your UPS (apc, by default),
then select NMC Settings.
5. For the Network Management Card you are configuring, select
Configure NMC Settings.
6. In the Network settings mode drop-down list, select the network
configuration option for your system: Manual, BootP, DHCP, or
DHCP & BootP.
– If you select Manual, enter the IP address, subnet mask, and default
gateway you obtained in step 1.
– If you select BootP, DHCP, or DHCP & BootP, a DHCP or BOOTP
server will assign the IP address, subnet mask, and default gateway
for the Network Management Card.
7.
10
Press Apply to save your changes.
Installation Manual
How to Recover from a Lost Password
You can use a local computer that connects to the Management Card through
the serial port to access the command line interface.
1.
Select a serial port at the local computer, and disable any service that
uses that port.
2. Connect the provided serial cable (APC part number 940-0299) to the
selected port on the computer and to the configuration port at the
Management Card.
3. Run a terminal program (such as HyperTerminal®) and configure the
selected port for 9600 bps, 8 data bits, no parity, 1 stop bit, and no flow
control.
4. Press ENTER, repeatedly if necessary, to display the User Name
prompt. If you are unable to display the User Name prompt, verify the
following:
– The serial port is not in use by another application.
– The terminal settings are correct as specified in step 3.
– The correct cable is being used as specified in step 2.
5. Press the Reset button. The Status LED will flash alternately orange
and green. Press the Reset button a second time immediately while the
LED is flashing to reset the user name and password to their defaults
temporarily.
6. Press ENTER, repeatedly if necessary, to display the User Name prompt
again, then use the default, apc, for the user name and password. (If
you take longer than 30 seconds to log on after the User Name prompt
is redisplayed, you must repeat step 5 and log on again.)
7. At the command line interface, use the following commands to change
the User Name and Password settings, both of which are now apc:
user -an yourAdministratorName
user -ap yourAdministratorPassword
For example, to change the Administrator user name to Admin,
type:
user -an Admin
8. Type quit or exit to log off, reconnect any serial cable you
disconnected, and restart any service you disabled.
Installation Manual
11
How to Access a Configured Network Management Card
Overview
After the Network Management Card is running on your network, you can use
the interfaces summarized here: Web interface, Telnet and SSH, SNMP, FTP,
and SCP.
For more information about the interfaces, see the User’s Guide.
Web interface
Use Microsoft Internet Explorer® (IE) 7.x or higher (on Windows operating
systems only) or Mozilla® Firefox® 3.0.6 or higher (on all operating systems)
to access the Web interface of the Network Management Card. Other
commonly available browsers may work but have not been fully tested by APC.
You can use either of the following protocols when you use the Web interface:
• The HTTP protocol (enabled by default), which provides authentication
by user name and password but no encryption.
• The HTTPS protocol, which provides extra security through Secure
Socket Layer (SSL); encrypts user names, passwords, and data being
transmitted; and authenticates Network Management Cards by means of
digital certificates.
To access the Web interface and configure the security of your device on the
network:
1. Address the Network Management Card by its IP address (or its DNS
name, if a DNS name is configured).
2. Enter the user name and password (by default, apc and apc for an
Administrator).
3. To enable or disable the HTTP or HTTPS protocol, use the Network
menu on the Administration tab, and select the access option under
the Web heading on the left navigation menu.
See the Security Handbook, available on the APC Network
Management Card Utility CD or from the APC Web site,
www.apc.com, for more information on selecting and configuring
network security.
12
Installation Manual
Telnet and SSH
You can access the command line interface through Telnet or Secure SHell
(SSH), depending on which is enabled. To enable these access methods, select
the Administration tab, the Network menu on the top menu bar, and the
access option under Console on the left navigation menu. By default, Telnet is
enabled. Enabling SSH automatically disables Telnet.
Telnet for basic access. Telnet provides the basic security of authentication
by user name and password, but not the high-security benefits of encryption. To
use Telnet to access the command line interface of the Network Management
Card from any computer on the same subnet:
1. At a command prompt, use the following command line, and press
ENTER:
telnet address
As address, use the Network Management Card’s IP address
(or DNS name, if configured).
2. Enter the user name and password (by default, apc and apc for an
Administrator, or device and apc for a Device User).
SSH for high-security access. If you use the high security of SSL for the
Web interface, use Secure SHell (SSH) for access to the command line
interface. SSH encrypts user names, passwords, and transmitted data.
The interface, user accounts, and user access rights are the same whether you
access the command line interface through SSH or Telnet, but to use SSH, you
must first configure SSH and have an SSH client program installed on your
computer.
See the User’s Guide for more information on configuring and
using SSH.
Simple Network Management Protocol (SNMP)
SNMPv1 only. After you add the PowerNet® MIB to a standard SNMP MIB
browser, you can use that browser to access the Network Management Card.
All user names, passwords, and community names for SNMP are transferred
over the network as plain text. The default read community name is public; the
default read/write community name is private.
Installation Manual
13
SNMPv3 only. For SNMP GETs, SETs, and trap receivers, SNMPv3 uses a
system of user profiles to identify users. An SNMPv3 user must have a user
profile assigned in the MIB software program to perform GETs and SETs,
browse the MIB, and receive traps. The default settings are no authentication
and no privacy.
Note: To use SNMPv3, you must have a MIB program that
supports SNMPv3.
The Network Management Card supports SHA or MD5
authentication and AES or DES encryption.
SNMPv1 and SNMPv3. To use InfraStruXure Central to manage the
Network Management Card on the public network of an InfraStruXure system,
you must have SNMPv1 enabled in the unit interface. Read access allows
InfraStruXure Central to receive traps from the Network Management Card.
Write access is required while you set InfraStruXure Central as a trap receiver.
To enable or disable SNMP access, you must be an Administrator. Select the
Administration tab, select the Network menu on the top menu bar, and use the
access option under SNMPv1 or SNMPv3 on the left navigation menu.
FTP and SCP
You can use FTP (enabled by default) or SCP to transfer downloaded firmware
to the Network Management Card, or to access a copy of the Network
Management Card’s event or data logs.
To use InfraStruXure Central to manage the UPS, you must have the FTP
Server option enabled in the Network Management Card interface.
To enable or disable FTP server access, you must be an Administrator. Select
the Administration tab, select the Network menu on the top menu bar, and use
the FTP Server option on the left navigation menu.
To transfer firmware, see the “File Transfers” chapter of the User’s
Guide.
To retrieve a copy of the event or data log, see the procedure “How
to use FTP or SCP to retrieve log files” in the “Logs” chapter of the
User’s Guide.
14
Installation Manual
Manage the security of your system
For detailed information on enhancing the security of your system
after installation and initial configuration, see the Security
Handbook, available on the APC Network Management Card
Utility CD and on the APC Web site, www.apc.com.
Installation Manual
15
Specifications
Physical
Size (H x W x D)
38.1 x 120.7 x 108 mm (1.50 x 4.75 x 4.25 in)
Weight
0.14 kg (0.30 lb)
Shipping weight
0.91 kg (2 lb)
Environmental
Elevation (above MSL)
Operating
Storage
0 to 3000 m (0 to 10,000 ft)
0 to 15 000 m (0 to 50,000 ft)
Temperature
Operating
Storage
-5 to 45°C (23 to 113°F)
-15 to 65°C (5 to 149°F)
Operating humidity
0 to 95%, non-condensing
Regulatory compliance
16
Radiated emissions
FCC Class A, VCCI Class A, ICES-003 Class
A, EN 55022 Class A, AS/NZS CISPR 22,
GOST-R 51318.22
Radiated immunity
GOST-R 51318.24, EN 55024
Installation Manual
Radio Frequency Interference
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.
USA —FCC
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with this
user manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference. The user
will bear sole responsibility for correcting such interference.
Canada—ICES
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.
Japan—VCCI
This is a Class A product based on the standard of the Voluntary Control Council for
Interference by Information Technology Equipment (VCCI). If this equipment is
used in a domestic environment, radio disturbance may occur, in which case, the
user may be required to take corrective actions.
この装置は、情報処理装置等電波障害自主規制協議会(VCCI)の基準
に基づくクラス A 情報技術装置です。この装置を家庭環境で使用すると、電波
妨害を引き起こすことがあります。この場合には、使用者が適切な対策を講ず
るように要求されることがあります。
Taiwan—BSMI
警告使用者 :
這是甲類的資訊產品 , 在居住的
環境中使用時 , 可能會造成射頻
干擾 , 在這種情況下 , 使用者會
被要求採取某些適當的對策。
Australia and New Zealand
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
European Union
This product is in conformity with the protection requirements of EU Council
Directive 2004/108/EC on the approximation of the laws of the Member States
relating to electromagnetic compatibility. APC cannot accept responsibility for any
failure to satisfy the protection requirements resulting from an unapproved
modification of the product.
This product has been tested and found to comply with the limits for Class A
Information Technology Equipment according to CISPR 22/European Standard EN
55022. The limits for Class A equipment were derived for commercial and industrial
environments to provide a reasonable protection against interference with licensed
communication equipment.
Attention: This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
Korean 한국
A 급 기기 ( 업무용 방송통신기기 )
이 기기는 업무용 (A 급 ) 으로 전자파적합등록을 한 기기이오니판매자
또는 사용자는 이 점을 주의하시기 바라며 , 가정외의지역에서 사용하
는 것을 목적으로 합니다 .
APC Worldwide Customer Support
Customer support for this or any other APC product is available at no charge in any of
the following ways:
•
Visit the APC Web site to access documents in the APC Knowledge Base and to
submit customer support requests.
– www.apc.com (Corporate Headquarters)
Connect to localized APC Web sites for specific countries, each of which
provides customer support information.
– www.apc.com/support/
Global support searching APC Knowledge Base and using e-support.
•
Contact the APC Customer Support Center by telephone or e-mail.
– Local, country-specific centers: go to www.apc.com/support/contact for
contact information.
For information on how to obtain local customer support, contact the APC
representative or other distributors from whom you purchased your APC product.
© 2009 APC by Schneider Electric. APC, the APC logo, InfraStruXure, Symmetra, and PowerNet are
owned by Schneider Electric Industries S.A.S., American Power Conversion Corporation, or their
affiliated companies. All other trademarks are property of their respective owners.
990-3194A-001
990-3194A-001*
4/2009
Download PDF