PIXCI EL1DB
PIXCI EL1DB
®
Dual Base Camera Link Frame Grabber
In One PCI Express x1 Expansion Slot
The PIXCI® EL1DB frame grabber provides two interfaces for
any two Base camera link cameras. The PIXCI EL1DB is
handled by EPIX’ software as if two PIXCI EL1 boards are
installed. The EL1DB will accept two trigger signals — one for
each camera; or allows a single trigger to control capture from
both cameras.
A strobe output signal is generated for each trigger. The PIXCI
EL1DB frame grabber supports two cameras with a combined
sustained bandwidth up to 191 MB/second. Compatible with the
PCI Express x1 bus, the PIXCI EL1DB frame grabber interfaces
to more than 100 of the newest, most advanced, highest
bandwidth machine vision cameras available.
The PIXCI® EL1DB and XCAP offers:
• 191 MB/sec burst data transfer rate.
Up to 191 MB/sec sustained data transfer from cameras to
x1 PCI Express bus.
• Two Camera Control Dialogs - independent or shared
– exposure, bit depth, gain, frame rate, etc.
• Cameras in free-run mode for maximum frame rate
sequence capture.
• Cameras in control mode for triggered image capture.
• $995.00 with XCAP-Lite imaging program.
The PIXCI® EL1DB is a plug-n-play frame grabber requiring no
hardware setup or adjustment. Load the software, install the
board, connect the cameras, and begin to capture images.
Supports One or Two Base Configuration
Camera Link Cameras
PCI Express x1 Bus Compatible
250 MB/sec Burst Data Transfers
191 MB/sec Sustained Data Transfer
Line Scan or Area Scan
Camera Frame Rate Sequence Capture
Triggered Image Sequence Capture
64-Bit Memory Addressing
Camera Integration & Async Reset Control
Integration From Microseconds to Minutes
Images Stored in Motherboard Memory or
RAID Array
Compatible with Windows XP, 2000, & Linux
RoHS Compliant
EPIX, Incorporated
381 Lexington Drive
Buffalo Grove, IL 60089 USA
Tel - 847 465 1818
Fax - 847 465 1919
Web: http://www.epixinc.com
E-mail: [email protected]
Specifications subject to change without notice. EPIX and
PIXCI are registered trademarks of EPIX, Inc. XCAP is a
trademark of EPIX, Inc. EPIX ® imaging products are
made in the USA.
© 2008 EPIX, Inc. All Rights Reserved. 13 JUNE 2008
The XCAP imaging program supports up to 4 PIXCI EL1DB
frame grabbers allowing use of eight Base configuration
Camera Link cameras in the same computer. The XCAP-Std
program allows simultaneous use of the PIXCI EL1DB with
other EPIX® frame grabbers supporting different camera
models, either Camera Link compatible or not. XCAP-Std also
offers video-to-disk capture, subject to the performance of the
host computer’s RAID array.
Programmer’s libraries and image processing subroutines are
available from EPIX for solving the most difficult particle
tracking, machine vision measurement, inspection, image
sequence analysis, and flow analysis tasks. Third party
software is also available.
Solutions and Support: EPIX, Inc. has been providing imaging
solutions and support for OEM machine vision manufacturers
and engineers since 1984. EPIX, Inc. assembles complete
imaging systems with cameras, frame grabbers, highperformance PCI Express buses, and with RAID arrays for
video-to-disk capture. EPIX imaging systems, custom-built to
your specifications, feature Intel motherboards and processors.
Contact EPIX, Inc., or an authorized EPIX, Inc. distributor, for
help selecting cameras, frame grabbers, imaging software,
optics, and computer systems.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement