NIC910 930 950HPRO QG A2

NIC910 930 950HPRO QG A2

Network WDR Speed Dome Camera

Quick Installation Guide

ZEIM-4000606G A.2

NIC910HPRO_NIC930HPRO_NIC950HPRO

Instruction ...............................................................

3

Major Components ...............................................................

5

Preparation Before Set Up ...............................................................

7

Configuring the IP Device ...............................................................

13

Video Display ...............................................................

14

Host Setting ...............................................................

15

Wan Setting ................................................................

18

Date Setting ................................................................

19

Video Setting ................................................................

20

Event Setting ................................................................

Video Adjustment ................................................................

24

25

User Account Management ................................................................

26

System Info ................................................................

Firmware Upgrade ................................................................

27

28

Factory Default ................................................................

30

Save Reboot ................................................................

31

Before attempting to connect or operate this product,please read these instructions carefully and keep this manual for future use.

2

PRECAUTIONS

&$87,21ODEHOLVDOVRVWXFNRQWKH

FDPHUD

7KHOLJKWHQLQJÀDVKZLWK

DUURZKHDGV\PEROZLWKLQ

DQHTXLODWHUDOWULDQJOHLV

LQWHQGHGWRDOHUWWKHXVHUWR

WKHSUHVHQFHRIXQLQVXODWHG

GDQJHURXVYROWDJHZLWKLQ

WKHSURGXFWVHQFORVXUH

WKDWPD\EHRIVXI¿FLHQW

PDJQLWXGHWRFRQVWLWXWHD

ULVNRIHOHFWULFVKRFNWR

SHUVRQV

7KHH[FODPDWLRQSRLQWZLWKLQ

DQHTXLODWHUDOWULDQJOHLV

LQWHQGHGWRDOHUWWKHXVHUWR

WKHSUHVHQFHRILPSRUWDQW

RSHUDWLQJDQGPDLQWHQDQFH

VHUYLFLQJLQVWUXFWLRQVLQ

WKHOLWHUDWXUHDFFRPSDQ\LQJ

WKHDSSOLDQFH

127(7KLVHTXLSPHQWKDVEHHQWHVWHGDQGIRXQG

WRFRPSO\ZLWKWKHOLPLWVIRUD&ODVV$GLJLWDO

GHYLFHSXUVXDQWWR3DUWRIWKH)&&5XOHV

7KHVHOLPLWVDUHGHVLJQHGWRSURYLGHUHDVRQDEOH

SURWHFWLRQDJDLQVWKDUPIXOLQWHUIHUHQFHZKHQ

WKHHTXLSPHQWLVRSHUDWHGLQDFRPPHUFLDO

HQYLURQPHQW7KLVHTXLSPHQWJHQHUDWHVXVHV

DQGFDQUDGLDWHUDGLRIUHTXHQF\HQHUJ\DQG

LIQRWLQVWDOOHGDQGXVHGLQDFFRUGDQFHZLWK

WKHLQVWUXFWLRQPDQXDOPD\FDXVHKDUPIXO

LQWHUIHUHQFHWRUDGLRFRPPXQLFDWLRQV

2SHUDWLRQRIWKLVHTXLSPHQWLQDUHVLGHQWLDODUHDLV

OLNHO\WRFDXVHKDUPIXOLQWHUIHUHQFHLQZKLFKFDVH

WKHXVHUZLOOEHUHTXLUHGWRFRUUHFWWKHLQWHUIHUHQFH

DWKLVRZQH[SHQVH

)&&&DXWLRQ7RDVVXUHFRQWLQXHGFRPSOLDQFH

H[DPSOH±XVHRQO\VKLHOGHGLQWHUIDFHFDEOHV

ZKHQFRQQHFWLQJWRFRPSXWHURUSHULSKHUDO

GHYLFHV$Q\FKDQJHVRUPRGL¿FDWLRQVQRW

H[SUHVVO\DSSURYHGE\WKHSDUW\UHVSRQVLEOHIRU

FRPSOLDQFHFRXOGYRLGWKHXVHU¶VDXWKRULW\WR

RSHUDWHWKLVHTXLSPHQW

7KHVHULDOQXPEHURIWKLVSURGXFWPD\EHIRXQG

RQWKHWRSRIWKHXQLW<RXVKRXOGQRWHWKHVHULDO

QXPEHURIWKLVXQLWLQWKHVSDFHSURYLGHGDQG

UHWDLQWKLVERRNDVDSHUPDQHQWUHFRUGRI\RXU

SXUFKDVHWRDLGLGHQWL¿FDWLRQLQWKHHYHQWRIWKHIW

0RGHO1R

6HULDO1R

&DXWLRQ

(QVXUHWKDW6DIHW\:LUHORFDWHGLQGRPHEDVHLVHQJDJHG

$OLJQQRWFKZLWK³23(1´DUURZDQGWXUQGRPHXQWLOQRWFKPHHWVDUURZLQ³/2&.('´SRVLWLRQ

&KHFNDVVHPEO\E\SXOOLQJRQGRPH$VVHPEO\VKRXOGQRWFRPHDSDUW

3

Installation Instructions

1) Read these instructions

All the safety and operating instructions should be read before the product is operated.

2) Keep these instructions

The safety instructions and instruction manual should be retained for future reference.

3) Heed all warnings

All warnings on the product and in the instruction manual should be adhered to.

4) Follow all instructions

All operating and use instructions should be followed.

5) Cleaning

Disconnect this video product from the power supply before cleaning.

6) Attachments

Do not use attachments not recommended by the video product manufacturer as they may cause hazards.

7) Water and Moisture

Do not use this video product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundary tub, in a wet basement, or near a swimming pool and the like.

8) Accessories

Do not place this video product on an unstable cart, stand, tripod, bracket or table. The video product may fall causing serious injury to a child or adult, and serious damage to the product. Use only with stand, tripod, bracket,or table recommended by the manufacturer, or sold with the video product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manu-facturer.

9) Ventilation

This video product should never be placed near or over a radiator or heat register. This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.

10) Power Source

This video product should be operated only from the type of power source in dicated on the marking label. If you are not sure the type of power supply to your location, consult your product dealer.

11) Power-Cord Protection

Power-Supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them. paying particular attention to cords at plugs, screws and the point where they exit from the product.

12) Lighting

For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the power supply and cable system. This will prevent damage to the video product due to lightning and power-line surges.

13) Overloading

Do not overload power supply and extension cords as this can result in a risk of fire or electric shock.

14) Object and Liquid Entry

Never push objects of any kind into this video product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electrical shock. Never spill liquid of any kind on the video product.

15) Servicing

Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

16) Damage Requiring service

Disconnect this video product from the power supply and refer servicing to qualified service personnel under the following conditions.

a.When the power-supply cord or plug is damaged.

b.If liquid has been spilled, or objects have fallen into the video product.

c.If the video product has been exposed to rain or water directly.

d.If the video product does not operate normally by following the operating instructions in this manual. Adjust only those controls that are covered by the -instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video prodcut to its normal operation.

17) Replacement Parts

When replacement parts are required, be sure the service technicaian has used replacement parts specified by the manufacturer have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

18) Safety Check

4

Instructions

Important Notice:

(1) The cable gland shall not be externally exposed and must be hidden inside the mount bracket/mount bracket with power box to prevent water from leaking in.

(2) If using power box (not provided) in the outdoors, it shall be UL certified Type 3R or better (Type 3, 3S, 4, 4X, 6, 6P) product.

Package Contents

Major Components

respective apparatus. connector for installation instruction.

Connects to the AC 24V power.

5) RS485 port

connecting to the WAN.

Connect this port directly to the LAN.

9) Connecting Ring

10) Lower Lid

11) Main Unit

12) Optical Dome

13) Safety Cord

5

Major Components

Alarm 1 and Alarm 2 support

IP speed dome

Power Cable

Black-AC24V

White-AC24V

Green-GND

*Please contact your supplier for adequate control panel. Improper control panel might cause damage for speed dome.

Junction Box Layout

6

Preparation Before Getting Start

PREFACE

MESSOA introduces the REAL TIME IP speed dome cameras excellent for both conventional surveillance system and digital networks. Outstanding camera performance with 18x,28x,36x zoom lens, highly accurate pan-tilt mechanism, the most forefront compressing technology and the best streaming technology makes it ideal for retail shops, schools, traffic control, airports, docks, factories, labs, buildings, warehouses and etc,.

FEATURES

Resolution of 720 x 480(NTSC) at 30 fps or 720 x 586 (PAL) at 25 fps(D1 resolution)

MPEG-4 ASP compliant hardware compression

Multi-cast: unlimited users access and remote monitor simultaneously

DoS, DDNS Embedded

Hareware motion Detection

Real day/night with ICR(switch optical filters to enhance sensitivity in poor lighting

conditions technology(*NIC930/950 ONLY)

4 pattern tours memorizing up to 6 mins of manual control

24 privacy zones masking

Pan range:360 continuous, tilt range:92

Pan speed:430 o

256 preset points

Alarm-in x6, Alarm-out x1 o

/sec preset, tilt speed:200 o

/sec preset

Bundled AP can remote manage and record up to 16 IP speed dome/video server at

a time

SDK support to develop your own AP

IP Software AP Application

The NVR software bundle 16 channels free. When you need to access the PTZ control, you must set the setting as follow:

Baud rate: 9600 (default)

Protocol: MESSOA D (default)

Minimum System Requirements

CPU Pentinum 4 2.4GHz and above

Hard Disk 40 GB or above

Memory 256 MB or above

Operating System Windows XP with SP2 or above / Windows 2000 with SP4 or above

Video Resolution SVGA or XGA with 1024x768 resolution

TRADEMARKS

*Microsoft, Windows, Windows NT, and Windows XP are regi-stered trademarks of

Microsoft Corporation in the U.S. and/or other countries.

*Ethernet is a registered trademark of Xerox Corporation.

*Other names of companies and products contained in thes-e operating instructions

may be trademarks or registered trademarks of their respective owners.

7

Preparation before setup

To configure your IP device, you have to use the Internet Explorer to login the IP device. Before that, your PC’s networks settings and the IP device’s IP address must be setup. Make sure all the connections are connected correctly, and then follow the procedures below to setup.

1. Setup your PC network

You have to match your PC’s TCP/IP setting with the IP device’s default settings before you can use IE browser to login it. This section tells you how to setup your PC’s

TCP/IP settings.

2.Setup IP device’s IP address

This IP device’s IP address can be setup manually or automatically by network service

(DHCP).

1.2.1 Setup your PC network

To set up the network of IP device via a PC, you have to change the TCP/IP settings of the PC.

The following are the default network settings of IP device.

IP Address: 192.168.0.100

Subnet Mask: 255.255.255.0

To access the IP device, the IP address of the PC should match the address below.

IP Address: 192.168.0.xxx

Subnet Mask: 255.255.255.0

NOTE: xxx should be a number from 1 to 254, but 100 is excepted.

The procedures below is the setup procedure of a PC using Windows XP as its OS.

When running an OS other than Windows XP, please refer to the manual included with the OS.

STEP1 Start up your PC.

STEP2 Click the [Start] and select the "Control Panel"

8

Preparation before setup

OPERATION/SETUP COMPARISON

■Function Comparison (Control via Network vs. Control via Camera Site)

Viewing Images

Pan/Tilt YES YES

Zoom/Focus

Iris Control

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES

YES YES

Network Address setup

User Authority

YES

YES

YES

Streaming Transmission Setup

Network Interface Setup YES

YES

YES

YES

NA

NA

NA

NA

NA

NA

Y: Yes

NA: Not Available yet

NOTE:

*1: The setup menus are operated from a control device such as a control panel or a system device such as a video multiplexer, a DVR or a system controller.

*2: Only authentication of network access user.

*3: Only authentication of camera site access.

9

Preparation before setup

STEP3 Double-click the "Network and Internet connections" icon.

STEP4 Double-click the "Network connections" icon

10

Preparation before setup

STEP5 Click “Local Area Connections”, and then click “Change settings of this connection” in the network Task menu.

STEP6 Click “Internet Protocol (TCP/IP)”, and then click the [Properties] button.

11

Preparation before setup

STEP7 Click the “Use the following IP address” radio button and enter the IP address and the subnet mask.

Please set the settings as below.

IP address: 192.168. 0.xxx

Subnet mask: 255.255.255. 0

(NOTE: xxx should be a number from 1 to 254, but 100 is excepted.)

STEP8 Click the [OK] button and the window dialog box closes

12

Configuring the IP device

This section describes how to configure the IP device. The product administrator has unlimited access to all setup windows and normal users can only watch the live image.

The IP device is configured under a standard browser (Microsoft Internet Explorer 6.0 or above).

Follow the procedures below to configure the IP device.

STEP1: Open a browser

STEP2: Enter the IP address of the IP device.

The default IP address is “192.168.0.100”

The “Login Page” is now displayed as below.

NOTE: Internet Explorer of 6.0 or above is highly recommended. If you don’t have the it, please download it from http://www.microsoft.com/windows/ie/downloads/default.

mspx

STEP3: Enter the Account name (factory default: Admin) and the Password (factory default: 123456).

STEP4: Select the language of the IP device user interface. You can select from

English, Traditional Chinese, Simplified Chinese, Japanese and Spanish. This user interface setting will disappear once you log out, if you want to change the default user interface language, please change the setting of [Host setting] after login successed.

STEP5: Click the button to login or click the button to re-enter again.

Once successfully login, the “Main Setup page” will be displayed as below.

13

Video Display

1.3.1 Video Display

This section tells you how to view live images via Internet Explorer.

STEP1: Click the [Video Display] on the “Main Setup page”.

The “Video Display page” is displayed as below.

STEP2: Check the

1

STEP3: Click the

2

[Mute] checkbox to select mute enable/disable

Audio Out] checkbox to enable/disable audio output from control

PC to IP device.

STEP4: Click the

3

STEP5:Click the

4 if you cannot see the video, and follow the instructions.

[Quit] to exit the live view and return to “Main Setup page”.

NOTE: If the streaming is disabled, you cannot see the live images here.

Be sure to set the Network Connections Type to Auto Negotiation to respective apparatus connected to this IP device via network. Otherwise, the maximum transmission performance might not be achieved. This is because the IP device follows MII standard.

14

Host Setting

1.3.2 Host Setting

This section tells you how to setup IP device’s host settings and LAN settings.

STEP1: Click the [Host Setting] on the “Main Setup page”.

The “Host setting page” is displayed as below.

STEP2:Configure these settings with reference to the table below. If you are still unsure what to set, contact your system administrator.

15

Host Setting

STEP3: Click the [Apply] button of each setting to confirm the settings or click the

4

[Reset] button to re-enter the parameters.

16

Host Setting

NOTE:

1.Once finished all settings, be sure to click the [Save Reboot] button, otherwise, some settings won’t take effect.

2.Check with your system administrator, if Client PC and IP device are setting in different

VLANs, please connect to WAN port.

3.Be sure to set the Network Connections Type to Auto Negotiation to respective apparatus connected to this IP device via network. Otherwise, the maximum transmission performance might not be achieved. This is because the IP device follows MII standard.

1.3.3 WAN Setting

This section tells you how to setup IP device’s WAN, DNS server and DDNS server settings.

STEP1: Click the [WAN Setting] on the “Main Setup page”.

The “WAN setting page” is displayed as below

17

WAN Setting

STEP2: Configure these settings with reference to the table below. If you are still unsure what to set, contact your system administrator.

STEP3: Click the

17

18

[Apply] button of each setting to confirm the settings or click the

[Reset] button to re-enter the parameters.

NOTE:

1. Check with your system administrator, if Client PC and IP device are setting in different VLANs, please connect to WAN port.

2 Once finished all settings, be sure to click the [Save Reboot] button, otherwise, some settings won’t take effect.

3. Be sure to set the Network Connections Type to Auto Negotiation to respective apparatus connected to this IP device via network. Otherwise, the maximum transmission performance might not be achieved. This is because the IP device follows MII standard.

18

Date Setting

1.3.4 Date Setting

This section tells you how to setup IP device’s date and time settings.

STEP1:Click the [Date Setting] on the “Main Setup page”. The “Date setting page” is displayed as below

STEP2:Configure these settings with reference to the table below. If you are still unsure what to set, contact your system administrator.

STEP3:Click the [Apply] button of each setting to confirm the settings or click the

[Reset] button to re-enter the parameters.

NOTE:Once finished all settings, be sure to click the [Save Reboot] button, otherwise, some settings won’t take effect.

Manually set date and time will be gone, if power off.

19

Video Setting

1.3.5 Video Setting

This section tells you how to setup IP device’s video and streaming settings.

STEP1:Click the [Video Setting] on the “Main Setup page”. The “Video setting page” is displayed as below

STEP2:Select streaming protocol [Version V1.0] (without audio function) or [Version

V2.0] (with audio function), and click [Setting] button to config settings, or [Reset] button to re-enter the parameters. Configure these settings with reference to the table below. If you are still unsure what to set, contact your system administrator.

Video setting of Version V1.0

20

Video Setting

Video setting of Version V2.0

Parameters Description

Camera name

LAN streaming

WAN streaming

The camera name is reserved for customer use.

Select the streaming mode in the LAN.

You can select TCP (TCP/IP) mode or Multicast mode to send video streaming.

You can also select Disable to disable the streaming via LAN.

Select the streaming mode in the WAN.

You can select TCP mode to send streaming or select Disable to disable the video streaming.

Select the multicast IP. Default settings is 228.5.6.1 Multicast IP

Multicast TTL

IGMP

Select the multicast TTL. Defualt setting is 255.

Enable or diable IGMP snooping. You may find a support package for helping you IGMP knowledge. Please visit our web site, and get the support document TS-00038.

Select video type connected to the video-in of this IP device. If you use an incorrect video type, some images might be lost.

Analog video

Resolution

Bitrate

Frame rate mode

Select the video resolution of the IP device.

Select the bit rate of the video streaming. You can select from 28Kbps to

3Mbps.

Note

: Lower bit rate consumes less bandwidth but delivers lower quality images.

High bit rate consumes more bandwidth but delivers higher quality images.

Select the frame rate mode.

Constant

: The streaming’s frame rate remains constant at all conditions.

Variant

:: The streaming’s frame rate will variants according to the images variability to keep the image quality good.

Frame rate Select the frame rate of the video streaming.

Click the “Apply” while setting to variable bitrate, then an estimate bitrate

Estimate Bitrate

Video register port

Video control port will show after item

Frame Integration

Low Pass Filter

Select the deinterlance mode.

Enable to reduce colour noise, and prevent data burst

Serial Port Baud Rate Select the Baud Rate setting of serial port.

Serial Port Control Select the Control setting of serial port.

Select the port for this IP device to support video registration function of the application program.

Select the port for this IP device to support video control function of the application program.

Video multicast port the application program.

Select the port for this IP device to support video multicast function of the application program.

STEP3:Click the [Apply] button of each setting to confirm the settings or click the

[Reset] button to re-enter the parameters.

NOTE:Once finished all settings, be sure to click the [Save Reboot] button, otherwise, some settings won’t take effect.

Manually set date and time will be gone, if power off.

21

Video Setting

Video setting of Version V2.0

22

Video Setting

Video setting of Version V2.0

Parameters Description

Camera name

Streaming Method

The camera name is reserved for customer use.

Select the streaming mode.

1.

TCP only

2.

Multicast only

3.

TCP & Multicast

4.

RTP over UDP

5.

RTP over Multicast

6.

RTP over UDP & Multicast

Select enable or disable the audio function. Audio

Multicast IP

Multicast TTL

Multicast Interface

IGMP

Analog video

Resolution

Select the multicast IP. Default settings is 228.5.6.1

Select the multicast TTL. Defualt setting is 255.

Select multicast interface

Select video type connected to the video-in of this IP device. If you use an incorrect video type, some images might be lost.

Select video type connected to the video-in of this IP device. If you use an incorrect video type, some images might be lost.

Bitrate

Frame rate mode

Select the video resolution of the IP device.

Select the bit rate of the video streaming. You can select from 28Kbps to

3Mbps.

Note

: Lower bit rate consumes less bandwidth but delivers lower quality images.

High bit rate consumes more bandwidth but delivers higher quality images.

Select the frame rate mode.

Constant

: The streaming’s frame rate remains constant at all conditions.

Variant

:: The streaming’s frame rate will variants according to the images variability to keep the image quality good.

Frame rate Select the frame rate of the video streaming.

Click the “Apply” while setting to variable bitrate, then an estimate bitrate

Estimate Bitrate will show after item

Frame Integration

LowPass Filter

Select the deinterlance mode.

Enable to reduce colour noise, and prevent data burst

Serial Port Baud Rate Select the Baud Rate setting of serial port.

Serial Port Control Select the Control setting of serial port.

RTSP port

Video RTP Over

Multicast

Audio RTPOver

Multicast

Video control port

Select the port for this IP device to support RTSP

Enable/disable the multicast video streaming via RTP protocol

Enable/disable the multicast audio streaming via RTP protocol

Select the port for this IP device to support video control function of the application program.

Video multicast port

Select the port for this IP device to support video multicast function of the application program.

STEP3:Click the [Apply] button of each setting to confirm the settings or click the

NOTE:

1.If you change Search Server Port1 & Search Server Port2, then you need to change ports in IP management software when searching for this IP device. Otherwise, you might not find this IP device in the network.

2.Once finished all settings, be sure to click the [Save Reboot] button, otherwise, some settings won’t take effect.

23

Event Setting

1.3.6 Event Setting

This section tells you the related setting of event triggering.

■ Event setting

Parameters Description

FTP Server Setting Set settings of FTP site

SMTP Setting

Event

Trigger

Action

Set settings of SMTP

Select event number

Select the trigger mode

Select the action mode

Status Window Windows to show event settings

STEP3:Click the [Apply] button of each setting to confirm the settings or click the

8

7

[Reset] button to re-enter the parameters.

24

Video Adjustment

1.3.7 Video Adjustment

This section tells you how to adjust the streaming video.

STEP1: Click the [Video Adjust] on the “Main Setup page”. The “Video adjust page” is displayed as below.

STEP2: Set the sensitivity of motion detection windows.

STEP3: Adjust the video by changing the value of “Hue”, “Brightness”, “Saturation”

6

3

7

4 5 and “Contrast”. See the images displayed above for the effect of the current setting.

STEP4: When satisfied with the video settings, click the [Apply] button of each setting to confirm the settings or click the [Reset] button to re-enter the parameters.

STEP5: Click the if you cannot see the video, and follow the instructions.

NOTE:

1.Once finished all settings, be sure to click the [Save Reboot] button, otherwise, some settings won’t take effect.

2.You may find a support package for helping you on better video quality adjustment.

Please visit our web site, and get the support document TS-00103.

25

User Account Management

1.3.8 User Account Management

This section tells you how to setup the accounts.

STEP1: Click the [User account] on the “Main Setup page”. The “Account management page” is displayed as below

STEP2: Setup the account names and their respective passwords. There are 1 root

(administrator) account and 10 common user accounts. Administrator account allows the user to watch the live view and setup everything; but common user account allows user only to watch the live image.

STEP3: Click the [Apply] button of each setting to confirm the settings or click the

[Reset] button to re-enter the parameters.

NOTE:

1.Once finished all settings, be sure to click the [Save Reboot] button, otherwise, some settings won’t take effect.

26

S

ystem Info

1.3.9 System Info

This section tells you how to see the system information of this IP device including system information, WAN status and system log.

STEP1: Click the [System info] on the “Main Setup page”. The “System information page” is displayed as below

STEP2: View the information at the 3 columns. This information is very useful to understand the IP device status and to resolve any problem that might occur.

■ System info

Column Description

System info

WAN status

It shows the firmware version, MAC address, production ID, and factory default type of IP device.

It shows the WAN port’s IP address, netmask, gateway, DNS server, DDNS host and connection status.

System log It shows the system event. This column is very useful to as a diagnostic tool.

STEP3:Click [Parameter List] where you may see all configurations of the IP device.

STEP4:Click [Server Report] to export related information of the IP device while reporting a support to your support channel.

27

Firmware Upgrade

1.3.10 Firmware Upgrade

This section tells you how to see update IP device’s firmware. You can always visit our web site for the latest firmware.

STEP1: Click the [Firmware] on the “Main Setup page”.

The “Firmware upgrade page-1” is displayed as below

STEP2: Click [Apply] button. The ‘’firmware upgrade page-2” will be displayed as below.

1

■ Date Setting

Parameters

Firmware images file

MD5 file

Description

You can upload the firmware images here.

Click the [browse] to select the image file and click the [enter].

You can always get the latest version at our website.

You can upload the MD5 file here.

Click the [browse] to select an MD5 file and click the [enter].

You can always get the latest version at our website.

28

Firmware Upgrade

NOTE: The version of the firmware image and the MD5 file to be uploaded must be the same, otherwise, the firmware upgrading will fail and the IP device will continue using previous firmware version.

STEP3: Click the [Upload] button to start upgrading or click the [Reset] to re-select the files.

5

STEP4: The upgrade process window shows a progress bar indicating upgrade status.

STEP5: The progress bar shows the upgrading is completed, and system is rebooting.

29

Factory Default

1.3.11 Factory Default

This section tells you how to see load IP device’s factory default setting.

STEP1: Click the [Factory Default] on the “Main Setup page”.

The “Factory default setting page” is displayed as below

STEP2: Click the [Apply] button to go to loading confirmation page or click the [Reset] button to exit to previous page.

STEP3: A confirmation page will be displayed. Click the [Save Reboot] button to start loading factory default settings.

30

Save Reboot

1.3.12 Save Reboot

This section tells you how to save all the settings and reboot this IP device. This is critical because some settings might not take effect before save and reboot.

STEP1: Click the [Save and reboot] on the “Main Setup page”.

The “Save and reboot page” is displayed as below.

STEP2: The Action LED indicator will light down to indicate that the IP device is rebooting. After around 30 seconds, the Action LED will light up again to indicate that the reboot is completed.

1.3.13 Logout

This section tells you how to logout the IP device. Be sure to logout this IP device once your setting is completed.

STEP1: Click the [Logout] on the “Main Setup page”.

You will logout and return to the “Login Page” displayed as below.

31

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement