APW Wyott | WK-1 | Operating instructions | APW Wyott WK-1 Operating instructions

INSTALLATION
AND
OPERATING
INSTRUCTIONS
Gas Griddles
MODELS: GGT-18i, -24i, -36i, -48i
&
MODELS: GGM-18i, -24i, -36i, 48i
(US & Canadian units are convertible and are assembled for Natural Gas)
(European units are not convertible and assembled for the appropriate gas)
IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain this manual for the life of the equipment. For Warranty
Service and/or Parts, this information is required.
Model Number
Serial Number
Date Purchased
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.
WARNING: Improper installation, operation, service or maintenance can cause property
damage, injury or death. Read and understand these instructions thoroughly before
positioning, installing, maintaining or servicing this equipment.
P/N 882203
APW WYOTT Foodservice Equipment Company
P.O. Box 1829
Cheyenne, WY 82003
+1 (307) 634-5801 Phone
+1 (307) 637-8071 Fax
+1 (800) 752-0863 Toll Free
www.apwwyott.com
1
CAUTION: These models are designed, built, and sold for commercial use. If these
models are positioned so the general public can use the equipment, make sure that
cautions, warnings, and operating instructions are clearly posted near each unit so that
anyone using the equipment will use it correctly and not injure themselves or harm the
equipment.
WARNING: Improper installation, adjustment, alteration, service or maintenance can
cause property damage, injury or death. Read the installation, operating and maintenance
instructions thoroughly before installing or servicing this equipment.
WARNING: Install per the spacing requirements listed in the installation section of this
manual. We strongly recommend having a competent professional install the equipment.
WARNING: For your safety do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance. Keep the area free and clear of
combustibles. (See ANZI Z83. 14B, 1991).
NOTICE: Instructions to be followed if anyone smells gas should be posted in a prominent
place. These may be obtained from the gas supplier.
GAS PRESSURE
The appliance and it’s individual shutoff valve (to be supplied by user) must be disconnected from the gas
supply piping system during any pressure testing of that system at test pressures in excess of ½ psi (3.45 kPa).
The appliance must be isolated from the gas supply piping system by closing it’s individual manual shut-off valve
during any pressure testing of the gas supply piping system at test pressures equal to or less than ½.
WARNING: A factory authorized agent should handle all maintenance and repair. Before
doing any maintenance or repair, contact APW Wyott.
Congratulations on your purchase of APW Wyott commercial cooking or refrigeration equipment. APW Wyott
takes pride in the design and quality of our products. When used as intended and with proper care and
maintenance, you will experience years of reliable operation from this equipment. To ensure best results, it is
important that you read and follow the instructions in this manual carefully.
TABLE OF CONTENTS
ITEM
PAGE
Safety Precautions ............................................. 3
Important Safety Instructions ............................. 4
General Information............................................ 4
Installation Instructions ....................................... 5
Location .............................................................. 6
Operation Instructions ........................................ 7
ITEM
PAGE
Service/Repair ......................................................... 7
Conversion ............................................................... 8
GGT Calibration Procedure/Probe Location............ 9
Troubleshooting ..................................................... 11
Replacement Parts Lists & Exploded Views ......... 12
Warranty................................................................. 16
LOCATION OF DATA PLATE
The data plate is located on the right side panel.
2
IMMEDIATELY INSPECT FOR SHIPPING DAMAGE
All containers should be examined for damage before and during unloading. The freight carrier has assumed
responsibility for its safe transit and delivery. If equipment is received damaged, either apparent or concealed, a
claim must be made with the delivering carrier.
A) Apparent damage or loss must be noted on the freight bill at the time of delivery. It must then be signed by
the carrier representative (Driver). If this is not done, the carrier may refuse the claim. The carrier can supply the
necessary forms.
B) Concealed damage or loss if not apparent until after equipment is uncrated, a request for inspection must be
made to the carrier within 15 days. The carrier should arrange an inspection. Be certain to hold all contents and
packaging material.
Installation and start-up should be performed by a qualified installer who thoroughly read, understands and
follows these instruction.
If you have questions concerning the installation, operation, maintenance or service of this product, write
Technical Service Department APW Wyott Foodservice Equipment Company, P.O. Box 1829, Cheyenne,
WY 82003.
SAFETY PRECAUTIONS
Before installing and operating this equipment be sure everyone involved in its operation is fully trained and is
aware of all precautions. Accidents & problems can result by a failure to follow fundamental rules and
precautions.
The following words and symbols, found in this manual, alert you to hazards to the operator, service personnel
or the equipment. The words are defined as follows:
DANGER: This symbol warns of imminent hazard which will result in serious injury or
death.
WARNING: This symbol refers to a potential hazard or unsafe practice, which could result
in serious injury or death.
CAUTION: This symbol refers to a potential hazard or unsafe practice, which may result in
minor or moderate injury or product or property damage.
NOTICE: This symbol refers to information that needs special attention or must be fully
understood even though not dangerous.
NOTICE: This product is intended for commercial use only. Not for household use.
CAUTION: These models are designed, built, and sold for commercial use. If these
models are positioned so the general public can use the equipment make sure that
cautions, warnings, and operating instructions are clearly posted near each unit so that
anyone using the equipment will use it correctly and not injure themselves or harm the
equipment.
WARNING: Improper installation, operation, service or maintenance can cause property
damage, injury or death. Read and understand these instructions thoroughly before
positioning, installing, maintaining or servicing this equipment.
3
WARNING: Keep the appliance free & clear of all combustible substances. If gas odor is
detected at any time, immediately shut unit down at the main shutoff valve. Do not permit
any open flames in the area of the appliance. Immediately contact an authorized Service
Agency or your local Gas Supplier for service.
WARNING: Do not obstruct either the air inlet (underneath unit) or the ventilation air (back
of unit). Provisions must be provided to provide an adequate air supply to the griddle.
NOTICE: Local codes regarding installation vary greatly from one area to another. The
National Fire Protection Association, Inc., states in its NFPA96 latest edition that local
codes are "Authority Having Jurisdiction" when it comes to requirement for installation of
equipment. Therefore, installation should comply with all local codes.
SPECIFICATIONS AND DIMENSIONS
MODEL
WIDTH
IN. (MM)
GGT-18i
GGT-24i
GGT-36i
GGT-48i
GGM-18i
GGM-24i
GGM-36i
GGM-48i
18 (457)
24 (610)
36 (915)
48 (1220)
18 (457)
24 (610)
36 (915)
48 (1220)
DEPTH
IN. (MM)
26 (661)
26 (661)
26 (661)
26 (661)
26 (661)
26 (661)
26 (661)
26 (661)
HEIGHT
IN. (MM)
# OF
BURNERS
BTU/kw
PER
BURNER
TOTAL
BTU/kW
HOUR
W.C.
IN.('Mbar')
17-3/4(451)
17-3/4(451)
17-3/4(451)
17-3/4(451)
17-3/4(451)
16-3/4(426)
16-3/4(426)
16-3/4(426)
1
2
3
4
1
2
3
4
37,500/11
25,000/7.3
25,000/7.3
25,000/7.3
37,500/11
25,000/7.3
25,000/7.3
25,000/7.3
37,500/11
50,000/14.6
75,000/22
100,000/29.3
37,500/11
50,000/14.6
75,000/22
100,000/29.3
6/10(15/25)
6/10(15/25)
6/10(15/25)
6/10(15/25)
6/10(15/25)
6/10(15/25)
6/10(15/25)
6/10(15/25)
Griddle Surface Dimensions
MODEL
GGT-18i and GGM-18i
GGT-24i and GGM-24i
GGT-36i and GGM-36i
GGT-48i and GGM-48i
WIDTH
IN. (MM)
17 13/16” / (452)
23 13/16” / (605)
35 13/16” / (910)
47 13/16” / (1215)
DEPTH
IN. (MM)
19 ½” / (496)
19 ½” / (496)
19 ½” / (496)
19 ½” / (496)
GENERAL INSTALLATION INSTRUCTIONS
Ensure gas supply and gas types, as shown on unit nameplate agrees with one another.
Unit installation must conform with the National Fuel Gas Code, ANSI Z223.1-1996, the National Gas Installation
Code, CAN/CGA-B149.1, or the Propane Installation Code, CAN/CGA-B149.2 as applicable and in accordance
with local codes.
Screw legs into the permanently fastened nuts on the four corners of the unit and tighten by hand. Level the unit
by turning the adjustment screw at the bottom of each leg. Do not slide unit with legs mounted, lift if necessary
to move unit.
Pipe threading compound must be resistant to the action of liquefied petroleum gases.
4
Caution: DO NOT use an open flame to check for leaks. Check all gas piping for leaks with a soap and water
solution before operating unit.
THESE UNITS ARE SUITABLE FOR INSTALLATION ON NON-COMBUSTIBLE SURFACES ONLY.
Noncombustible clearances:
0" sides (0 mm)
0" rear (0 mm)
4" floor (102mm)
Do not obstruct the flow of combustion and ventilation air, under the unit by the legs or behind the unit by the
flue.
Adequate clearance for air openings into the combustion chamber is required. Do not place objects between the
bottom of the unit and the counter top.
There must be adequate clearance for removal of the front panel. All major parts except the burners are
removable thru the front if the gas line is disconnected.
European Community Installation Instructions:
"THIS APPLIANCE MUST BE FITTED BY A COMPETENT PERSON. IN THE UK, CORGI REGISTERED
INSTALLERS (INCLUDING THE REGIONS OF BRITISH GAS) UNDERTAKE TO WORK TO SAFE AND
SATISFACTORY STANDARDS. THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE GAS
SAFETY (INSTALLATION AND USE) REGULATIONS AND THE RELEVANT BUILDING REGULATIONS / IEE.
REGULATIONS. DETAILED RECOMMENDATIONS ARE CONTAINED IN THE FOLLOWING BRITISH
STANDARD CODES OF PRACTICE -BS 6172, BS 5440 PART 2, BS 6891"
"THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE RULES IN FORCE"
"MUST BE INSTALLED IN A WELL VENTILATED AREA. Ventilation requirements ie. B.S. 5440."
LIGHTING INSTRUCTIONS
GGT and GGM Griddles are furnished with either a pilot safety valve or a standing pilot (not available in the
European Community). Please follow the instructions for your unit.
Pilot Safety Valve Lighting Instructions
1. Turn on main gas supply to unit, on-off valve located behind the unit (not supplied with unit).
2. Turn the burner control knobs to "OFF" position. Wait at least 5 minutes to allow any gas which may have
accumulated in the firebox compartment to escape.
3. Through the hole in the front panel, press red button on the pilot safety valve and light through observation
hole in firebox. Keep red button on pilot safety depressed for at least 1 minute after pilot has lit. If pilot does
not light, repeat this step.
Standing Pilot Lighting Instructions (Not Available in the European Community)
The pilot lights on the griddles have been set at the factory. A screwdriver maybe required for the first lighting to
adjust the flame for your elevation.
1. Turn off the manual shut off valve and wait 5 minutes to clear the gas.
2. Turn all knobs to the "OFF" position.
3. Turn the manual shut off valve on.
4. Hold an ignition source (match) at the pilot. When the flame is established, remove the ignition source.
5
5. Turn the burner knobs to "HI". If the burner does not ignite, promptly open the pilot valve more. If the pilot
flame appears larger than necessary, turn it down and reset burner ignition. The pilot flame should be as
small as possible but large enough to guarantee reliable ignition of the burners when the knobs are turned to
"HI".
Lighting main burner
To light burner, turn knob to “max.” Then back off to the desired flame level. The range of adjustment is virtually
infinite between high and off. (At small flame, there is a preset low).
Main burner air supply:
1. For efficient burner operation, a proper balance of gas volume and primary air supply must be maintained
which will result in complete combustion. Insufficient air supply results in a yellow streaming flame. Primary
air supply is controlled by an air shutter on the front of the burner.
2. Loosen the screws on the front of the burner and adjust the air shutter to just eliminate the yellow tips of the
burner flame. Lock the air shutter in place by tightening the screws.
European Community
If adjustment becomes necessary in the field, it should be done by a factory authorized and trained technician
who should seal the screw after the adjustment to safeguard against unauthorized tampering by the end user.
All burners are lit from constantly burning pilots. Turning the thermostat to the desired temperature is all that is
required to put the unit in service.
Do not permit fans to blow directly at the unit. Wherever possible, avoid open windows next to the units' sides or
back. Avoid wall type fans which create air cross-currents within a room.
It is also necessary that sufficient air should be allowed to enter the room to compensate for the amount of air
removed by any ventilating system. Otherwise, a subnormal atmospheric pressure will occur, which will effect
operation and cause undesirable working conditions.
A properly designed and installed hood will act as the heart of the ventilating system for the room or area in
which the unit is installed and will leave the unit independent of changing draft conditions.
All valves must be checked and lubricated periodically. This must be done by an authorized service
representative in your area.
OPERATING INSTRUCTIONS
Season Griddle:
Heat to low temperature (300 - 350 F/150-180C) and pour on a small amount of cooking oil, about one ounce
(30cc) per square foot of surface. Spread the oil over the entire griddle surface with a cloth to create a thin film.
Wipe off any excess oil with a cloth. Repeat this procedure 2 to 3 times until the griddle has a slick, mirror-like
surface.
Operation:
Turn the burners on about 15-20 minutes before cooking for preheating. Set the knobs to the desired flame
height or temperature. Each valve will control the gas flow to the burner to bring that area of the plate up to the
set temperature. If different temperature settings are to be used, adjoining areas should be set at progressively
higher temperatures using the lowest temperatures on the outside burners. A uniform and systematic approach
to the loading of the griddle will produce the most consistent product results.
6
CLEANING / MAINTENANCE
CAUTION: Use only non-abrasive cleaners. Abrasive cleaners could scratch the finish of
your unit, marring it’s appearance and making it susceptible to dirt accumulation. Do Not
use steel wool, other abrasive cleaners or cleaners/sanitizers containing chlorine, iodine,
ammonia or bromine chemicals as these will deteriorate the stainless steel and glass
material and shorten the life of the unit.
Initial Cleaning:
Prior to operating your new griddle, thoroughly wash the griddle surface and the exterior with a mild detergent or
soap solution. Do not use abrasive cleaners since this might damage the cabinet finish. If the stainless steel
surfaces become discolored, scrub by rubbing only in the direction of the finished grain.
Cleaning:
1. Always turn unit off and allow it to cool completely before cleaning. Clean thoroughly before first use.
2. After each use, clean the griddle with wire brush or flexible spatula.
3. Once a day, thoroughly clean splash back, sides and front. Remove the grease drawer, empty it and wash it
out.
4. Once a week, clean the griddle surface thoroughly. If necessary, use a griddle stone, wire brush or steel
wool on the surface. Rub with the grain of the metal while the griddle is still warm. A detergent may be used
on the plate surface to help clean it; but, care must be taken to be sure the detergent is thoroughly removed.
After removal of the detergent, the surface of the plate should then be covered with a thin film of oil to
prevent rusting. Clean stainless surfaces with a damp cloth and polish with a soft dry cloth. To remove
discoloration, use a nonabrasive cleaner. After each "weekly" cleaning, the griddle must be seasoned again.
If the griddle usage is very high, the "weekly" cleaning procedures may be done more often than once a
week.
CAUTION: Clean the regulator at least once a month. Make sure the vent opening is open
and not blocked in any way. Failure to do so will cause variations in pressure. Your unit
will not function as well and it could shorten the life of the product
Extended Shutdown:
Turn the manual shutoff valve to "OFF"; (field installed valve not supplied by the manufacturer); turn all control
knobs to the "OFF" position; and shut off the pilot flame by turning the adjustment on the pilot valve.
If the griddle is to be shut down for an extended period, put a heavy coat of grease over the griddle plate.
SERVICE / REPAIR
NOTE: THIS APPLIANCE MUST ONLY BE SERVICED BY AN AUTHORIZED AGENT.
NOTE: Parts protected by the manufacturer or his agent are not to be adjusted by the installer
unless the installer is an authorized service agent.
If you have any questions or problems contact your nearest APW/Wyott Service Representative.
7
CONVERSION
Instructions are for conversion from Natural Gas to Propane (L.P.) on all GGT & GGM models.
The conversion should be done before connecting the unit to the gas supply.
GGT Models
1. Remove the knobs and front panel.
GGM Models
Screw
2. Unscrew bolts and pilot valve, then
remove the manifold.
2. Remove the supply tubes that go
between the thermostats and the
orifice bracket.
3. Unscrew and remove the orifice
fittings from the valve. Change the
orifices to the size recommended
for propane (L.P.). For units with a
pilot safety valve you must also
change the pilot orifice to the other
pilot orifice supplied.
Note: Unit Number on Side of
Orifice Fittings
Plastic Insert
4. Replace the orifice fittings into the
valve.
5. Replace the front panel and knobs.
6. Before installing the regulator,
unscrew the octagonal cap. With
the brass portion of the cap up, you
can read(NAT) on the plastic insert.
Snap the insert out of the cap, flip it
over and snap back in place. You
can now read(L.P.)
Regulator with Brass Cap
7. Continue with installation.
8
L.P. Position of Insert
GGT CALIBRATION PROBE LOCATION
CALIBRATION PROCEDURE FOR GGT GRIDDLES
Locate the reading positions
Make sure the griddle surface is clean. Grease or food particles on the griddle will result in inaccurate
thermostat calibration.
Mark the locations where the temperature probe will be placed for testing. See the sketch provided. Starting
from the left side of the griddle, measure 8” to the right and 10-5/8” from the rear splash guard. With a felt tip
pen mark this location. This is the location directly over the center of the left thermostat bulb. From this point
measure right 10” remaining 10-5/8” from the rear splash guard. Mark this location with a felt tip pin. This is the
location over the next thermostat bulb. For a 36” GGT repeat this one more time 10” to the right and for the 48”
GGT repeat this twice more 10” to the right always remaining 10-5/8” from the splash guard. After all locations
are marked center the temperature probe on each marked location, and then trace a circle around the
probe.
This procedure will place the temperature probe over the center of each thermostat bulb, and this is the only
place temperature readings should be taken.
Set all thermostats to 350ºF and allow them to cycle three to four times, or allow the griddle to preheat for ½
hour before proceeding. This makes sure the griddle temperatures have saturated the surface.
Determine the differential
Note the temperature for each section of the griddle as the burners ignite.
Note the temperature for each section of the griddle as the flame extinguishes.
The flame extinguish temperature minus the ignition temperature equals the differential.
EXAMPLE:
Flame extinguished 367ºF
Flame ignition 341ºF
Difference 26º F = Differential
9
If the temperature differential is large than 75ºF, there is probably a problem with your system. It may not be the
thermostat. First make sure you thermostat probe is flat against the griddle plate and is making good contact.
Dirt under the probe will cause inaccurate readings. Next make sure the thermostat bulb is held tightly in its
holder. If you can pull the capillary tube and the bulb moves it is not held tight enough against the griddle plate.
This will cause variations in the temperature of the griddle surface. If both of these items have been checked
and you still have a differential over 75ºF then the thermostat is bad replace it.
Determine the average temperature
Note the temperature for each section of the griddle as the burners ignite.
Note the temperature for each section of the griddle as the flame extinguishes.
The flame extinguish temperature plus the flame ignition temperature divided by two equals the average
temperature.
EXAMPLE:
Flame extinguished 367ºF
Flame ignition 341ºF
708º / 2
Average temperature = 354ºF
If the average temperature is within 15ºF of the dial marking you probably leave the calibration where it is. If the
average temperature is outside of 15ºF of the dial setting you will want to calibrate the thermostat. To calibrate a
thermostat first remove the knob by pulling it straight off the shaft. Next take a small flat head screw drive and
turn the screw inside the shaft, clockwise to decrease, counterclockwise to increase. ¼ turn clockwise will
decrease the temperature approximately 24ºF. ¼ turn counterclockwise will increase the temperature
approximately 24ºF. Adjust and re-measure the average temperature until you get the temperature to your
desired point.
NOTE: avoid making more than ½ turn at a time. Calibration is not linear and you can get the thermostat
significantly out of calibration to a point where it is difficult to reset.
If after adjusting the thermostat three times and getting no change in calibration the thermostat is bad. Then
replace the thermostat.
NOTES: _________________________________________________________________________________
_________________________________________________________________________________________
________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
10
TROUBLESHOOTING GUIDE
PROBLEM
POSSIBLE CAUSE
Thermostat is bad.
Heat does not come on when
thermostat is turned on.
Pilot burner not lit.
Gas valve is bad.
Obstructed pilot orifice.
Pilot burner will not light.
Pilot gas turned off at automatic pilot.
Automatic pilot valve is bad.
Thermocouple is bad.
Thermocouple is not hot enough.
Pilot burner will not stay lit.
Obstructed or wrong size pilot orifice.
Gas supply is not purged of air.
Air is blowing pilot light out.
Automatic pilot valve is bad.
Heat is set too high.
Fat appears to smoke excessively.
Moisture in the food may be turning into steam.
Heat is set too high.
Food sticks to griddle.
Griddle surface needs cleaning and/or seasoning.
Surface under food may not have been covered with enough cooking
oil.
Heat is set too high.
Food burned around edges or
contains dark specks.
Griddle surface needs cleaning and/or seasoning.
Surface under food may not have been covered with enough cooking
oil.
Heat is set too high.
Food is undercooked inside.
Food may not have been cooked for long enough time.
Food itself may have off flavor.
Food tastes greasy or has
objectionable off-flavor.
Food may have been stored improperly before cooking.
Too much griddle fat used.
Heat is set too low.
Heat is set too high
Noticeable build-up of gum on griddle.
Griddle surface needs cleaning and/or seasoning.
Too much griddle fat used.
11
PARTS LISTS & EXPLODED VIEWS
GGM GRIDDLES (EXPLODED VIEW)
12
GGM – PARTS LIST
Item
P/N
Description
Quan
Item
Weldment, Griddle GGM-18
Weldment, Griddle GGM-24
Weldment, Griddle GGM-36
Weldment, Griddle GGM-48
Body, 18" Firebox GGM
Body, 24" Firebox GGM
Body, 36" Firebox GGM
Body, 48" Firebox GGM
Tube, Pilot Supply GGM-18
Tube, Pilot Supply GGM-24/36/48
Pilot, Top
Pilot, Broiler
Support, Leg-18
Support, Leg-24
Support, Leg-36
Support, Leg-48
Side, Grease Chute
Plug, 1/8 NPTM
Side Panel, RH
#8 X 3/8
Support, Burner-18
Support, Burner-24
Support, Burner-36
Support, Burner-48
Orfice, #44
Nut, Hex, KEPS 10-32
Valve, Pilot 90° 1/8NPT X 3/16CC GGM-18
Pilot Valve GGM-24/36/48
Burner, "S”
Burner, "U”
Valve, Gas, On-Off
1
1
1
1
1
1
1
1
1
Varies
1
Varies
2
2
2
2
Varies
Varies
1
4
2
2
2
2
Varies
Varies
Varies
Varies
1
Varies
Varies
24
15
218215-20
218216-20
218217-20
218218-20
218215-11
218216-11
218217-11
218218-11
21820728
21820727
2066154
2092800
22030005
22030010
22030015
22030020
218207-16
2092517
22031254
81546-00
218207-17
218208-17
218209-17
218210-17
2066844
8417100
2065643
2068001
21813075
21813175
2068200
16
8436200
Nut, Hex 5/16-18 S/S
17
18
8153100
218207-29
218208-25
21820715
22011199
21820815
21820830
21820915
21820930
21821015
21821030
#8-32 X 3/8 Type T
Bracket, Pilot GGM-18
Bracket, Pilot GGM-24/36/48
Manifold, 18" GCRB
Manifold, 18" GCRB Pilot Safety
Manifold, 24" GCRB
Manifold, 24" GCRB Pilot Safety
Manifold, 36" GCRB
Manifold, 36" GCRB Pilot Safety
Manifold, 48" GCRB
Manifold, 48" GCRB Pilot Safety
20
22031254
Side Panel, LH 1
21
22
23
8163100
21813085
22011191
218208-18
218209-18
218210-18
M/S Tr Hd Ph 10-32x1/4
Spacer
Baffle, 18" Front Heat
Baffle, 24" Front Heat
Baffle, 36" Front Heat
Baffle, 48" Front Heat
1
2
3
4
5
6
7
8
9
10
11
12
13
14
19
P/N
Description
Quan
33
36
37
38
39
40
41
42
43
44
45
46
2425400
2425500
8861000
218215-12
218216-12
218217-12
218218-12
8196601
22011193
22011253
22011373
22011493
30047501
8170700
8837120
22011195
22011255
22011375
22011495
81973-00
8353000
8633700
8706300
8837129
8832600
8837130
2067300
8809920
8825300
8822325
43813103
Varies
Varies
1
1
1
1
1
4
1
1
1
1
Varies
Varies
1
1
1
1
1
4
2
4
Varies
1
1
1
1
1
1
1
1
Varies
47
43813149
Varies
1
Varies
1
1
1
1
1
1
1
1
48
49
50
52*
53*
55*
56*
58*
59*
60*
61*
2092903
2066850
2092904
8899300
8838800
8837201
8837190
2065847
2092610
2092592
2092611
1
62*
2092613
Pan, Grease 18" Short Draw
Pan, Grease 24" Short Draw
Label, Spec
Panel, Back GGM-18
Panel, Back GGM-24
Panel, Back GGM-36
Panel, Back GGM-48
Nut, U-Type
Panel, Control
Panel, Control
Panel, Control
Panel, Control
Guide, Grease Slide
Screw, 10-32x1/2, Type AB
Label, Orifice Size
Baffle, Front Panel 18"
Baffle, Front Panel 24"
Baffle, Front Panel 36"
Baffle, Front Panel 48"
T/S #10 X ½ TPB Tr Hd
Pop Rivet
Leg, HD 2” Diameter W/Foot
Knob, Metal Cookline .375D shaft
Label, Instr.-location
Label, Service Hotline
Decal, Oper. Instr.
Regulator, Convertible 3/4 ½ PSIG
Decal, Improper Install
Decal, Leg
Decal, UL Sanitation, NSF Std. 4
Label, Warning, Hot Surface
Label, Warning, Hot Surface
(French)
Pilot Natural @ 6" W.C.
Orfice, #50
Orifice, Pilot L.P.
List Of Service Agencies
Manual, GGT-H/GGM-H Champion II
Bag, Cloth, 4"x6" W/drawstring
Tag, Orifice Location
Logo, APWWYOTT 2” Diam Foot
Coupling, 3/4" Pipe X 3" Long
Nipple, 3/4 X Close Schd 40 Black
Elbow, 3/4 Black Pipe
Pipe, Black 3/4" X 23" Long Thrd Both
25
26
27
28
29
30
31
32
Varies
Varies
1
1
1
1
Ends
*NOT SHOWN
13
1
Varies
Varies
Varies
1
1
1
1
1
1
1
1
1
GGT GRIDDLES (EXPLODED VIEW)
14
GGT – PARTS LIST
Item
P/N
Description
Quan
Item
218219-60
218220-60
218221-60
218222-60
2092614
81108-00
2065614
2068001
22030005
22030010
22030015
22030020
Weldment, Griddle, GGT -18
Weldment, Griddle, GGT -24
Weldment, Griddle, GGT -36
Weldment, Griddle, GGT -48
Elbow, 3/8CC X 3/8NPT, No Hood
M/S Tr Hd Ph 6-32 x 1"
Valve, Pilot GGT-18
Pilot Valve GGT-24/36/48
Support, Leg 18”, i-Line
Support, Leg 24”, i-Line
Support, Leg 36”, i-Line
Support, Leg 48”, i-Line
1
1
1
1
Varies
Varies
1
Varies
2
2
2
2
30*
32
33
34
35
36*
37
38
39
40
41
42
2300100
1018064
8509300
8436200
8417100
2300000
8170700
30047501
8353000
8163100
8825300
8153100
6
8400100
Nut, Hex Keps, #6-32
Varies
43*
8824518
7
8
9
10
11
12
Plug, 1/8 NPTM
Side Panel, LH
Side Panel, RH
Tube, T-Stat/Hood Orifice GGT-24/36/48
Bracket, Thermostat GGT
Firebox, GGT -18
Firebox, GGT -24
Firebox, GGT -36
Firebox, Ggt -48
Bracket, Manifold GGT
Tube, T-Stat/Hood Orifice
1
1
1
Varies
Varies
1
1
1
1
Varies
Varies
44
45*
46*
47*
48
13
14
2092517
22031254
22031254
21822047
21822034
21821911
21814020
21822121
21814022
21822035
21822046
50
51
52
8837190
8837201
8838800
8899300
2425400
2425500
2066154
2092800
8633700
8196601
81973-00
15
21821915
Manifold, GGT-18H
1
53
43813149
Manifold, GGT-24H
Manifold, GGT-36H
Manifold, GGT-48H
Manifold, GGT-18H Pilot Safety
Manifold, GGT-24H Pilot Safety
Manifold, GGT-36H Pilot Safety
Manifold, GGT-48H Pilot Safety
Side, Grease Chute
Elbow, 3/8C X 3/8 Ipt Male
Elbow, 1/8 Pipe To 3/8 Comp.
Burner, "S” GGT-18
Burner, "U” GGT-24/36/48
3/8 Comp X 3/8 NPT Male Straight
Varies
1
1
1
1
1
1
2
Varies
Varies
1
Varies
Varies
54
16
17
18
19
19
20
21822029
21822130
21822029
21821930
21822030
21822035
21822235
218207-16
2092506
2069020
2065855
2065850
2092623
60
61
21821920
21814036
8861000
43813103
22031193
22031253
22031373
22031493
8706315
2066850
2066854
2092904
218208-26
21
2092903
Pilot Nat @ 6" W.C. GGT-24/36/48
1
63
21821949
22
23
24
2067700
21814019
21821912
21822026
21822127
21822228
21822045
21822044
2067300
21723090
2066837
2066844
Thermostat, Gas Snap Action
Bracket, Orifice
Panel, Back GGT -18
Panel, Back GGT -24
Panel, Back GGT -36
Panel, Back GGT -48
Tube, Manifold/T-Stat
Tube, Manifold/T-Stat GGT-24/36/48
Regulator, Convertable 3/4 ½ PSIG
Cover, Thermostat Bulb
Orifice, #37 GGT-18
Orifice, #44 GGT-24/36/48
64
65
66
67
68
69
21822048
8837130
8822325
8809920
2092624
8837120
8832600
1
2
3
4
5
15*
25
26
27
28
29
49
55
56
57
58
59
Varies
2
1
1
1
1
Varies
1
1
Varies
1
Varies
15
P/N
Description
Bags, Poly 36x27x44
Insulation, Thermostat Bulb
Washer, Flat, SAE, 5/16
Nut, Hex 5/16-18 S/S
Nut, Hex, Keps 10-32
29x19x44 Poly
Screw, 10-32x1/2, Type AB
Guide, Grease Slide
Pop Rivet
M/S Pn Hd Ph 10-32 X 1/4"
Decal, Leg
#8-32 X 3/8 Type T
Decal, Dial Plate Thermostatic
Griddle
Tag, Orifice Location
Bag, Cloth, 4"x6" W/Drawstring
Manual, GGT-H/GGM-H Champion Ii
List Of Service Agencies
Pan, Grease 18"
Pan, Grease 24"
Pilot, Top GGT-18
Pilot, Broiler GGT-24/36/48
Leg, HD 2” Diameter W/Foot
Nut, U-Type
T/S #10 X ½ TPB Tr Hd
Label, Warning Hot Surface
(French)
Bracket, Pilot Top T-Pile GGT-18
Bracket, Pilot GGT-24/36/48
Label, Spec
Label, Warning, Hot Surface
Panel, Control GGT-18H
Panel, Control GGT-24H
Panel, Control GGT-36H
Panel, Control GGT-48H
Knob, GS-1A shaft metal set screw
Orifice, #50 GGT-18
Orifice, #54 GGT-24/36/48
Orifice, Pilot L.P. GGT-24/36/48
Logo, APWWYOTT Casted
Tube, Pilot Supply Standing GGT18
Tube, Pilot Supply GGT-24/36/48
Decal, Oper. Instr.
Decal, UL Sanitation, NSF Std. 4
Decal, Improper Install
3/8 Comp X 1/8 NPT Male Straight
Label, Orifice Size
Label, Service Hotline
*NOT SHOWN
Quan
1
2
4
8
6
1
20
2
2
2
1
4
1
1
1
1
1
Varies
Varies
1
1
4
4
4
1
1
1
1
1
1
1
1
1
Varies
Varies
Varies
Varies
1
1
Varies
1
1
1
Varies
1
1
APW WYOTT EQUIPMENT LIMITED WARRANTY
APW Wyott Foodservice Equipment Company warrants it's equipment against defects in materials and workmanship, subject to the
following conditions:
This warranty applies to the original owner only and is not assignable.
Should any product fail to function in its intended manner under normal use within the limits defined in this warranty, at the option of
APW Wyott such product will be repaired or replaced by APW Wyott or its Authorized Service Agency. APW Wyott will only be
responsible for charges incurred or service performed by its Authorized Service Agencies. The use of other than APW Wyott Authorized
Service Agencies will void this warranty and APW Wyott will not be responsible for such work or any charges associated with same. The
closest APW Wyott Authorized Service Agent must be used.
This warranty covers products shipped into the 48 contiguous United States, Hawaii, metropolitan areas of Alaska and Canada. There will
be no labor coverage for equipment located on any island not connected by roadway to the mainland.
Warranty coverage on products used outside the 48 contiguous United States, Hawaii, and metropolitan areas of Alaska and Canada may
vary. Contact the international APW Wyott distributor, dealer, or service agency for details.
Time Period
One year for parts and one year for labor, effective from the date of purchase by the original owner. The Authorized Service Agency may,
at their option, require proof of purchase. Parts replaced under this warranty are warranted for the un-expired portion of the original
product warranty only.
Exceptions
* Gas/Electric Cookline: Models GCB, GCRB, GF, GGM, GGT, CHP-H, EF, EG, EHP. Three (3) Year Warranty on all
component parts, except switches and thermostats. (2 additional years on parts only. No labor on second or third year.)
* Broiler Briquettes, Rock Grates, Cooking Grates, Burner Shields, Fireboxes: 90 Day Material Only. No Labor.
* Heat Strips: Models FD, FDL, FDD, FDDL. Two (2)Year Warranty on element only. No labor second year.
* Glass Windows, Doors, Seals, Rubber Seals, Light Bulbs: 90 Day Material Only. No Labor.
In all cases, parts covered by extended warranty will be shipped FOB the factory after the first year.
Portable Carry In Products
Equipment weighing over 70 pounds or permanently installed will be serviced on-site as per the terms of this warranty. Equipment
weighing 70 pounds or under, and which is not permanently installed, i.e. with cord and plug, is considered portable and is subject to the
following warranty handling limitations. If portable equipment fails to operate in its intended manner on the first day of connection, or
use, at APW Wyott's option or its Authorized Service Agency, it will be serviced on site or replaced.
From day two through the conclusion of this warranty period, portable units must be taken to or sent prepaid to the APW Wyott
Authorized Service Agency for in-warranty repairs. No mileage or travel charges are allowed on portable units after the first day of use. If
the customer wants on-site service, they may receive same by paying the travel and mileage charges. Exceptions to this rule: (1)
countertop warmers and cookers, which are covered under the Enhanced Warranty Program, and (2) toasters or rollergrills which have in
store service.
Exclusions
The following conditions are not covered by warranty:
* Equipment failure relating to improper installation, improper utility connection or supply and problems due to ventilation.
* Equipment that has not been properly maintained, calibration of controls, adjustments, damage from improper cleaning and
water damage to controls.
* Equipment that has not been used in an appropriate manner, or has been subject to misuse or misapplication, neglect, abuse,
accident, alteration, negligence, damage during transit, delivery or installation, fire, flood, riot or act of god.
* Equipment that has the model number or serial number removed or altered.
If the equipment has been changed, altered, modified or repaired by other than an Authorized Service Agency during or after the warranty
period, then the manufacturer shall not be liable for any damages to any person or to any property, which may result from the use of the
equipment thereafter.
This warranty does not cover services performed at overtime or premium labor rates. Should service be required at times which normally
involve overtime or premium labor rates, the owner shall be charged for the difference between normal service rates and such premium
rates. APW Wyott does not assume any liability for extended delays in replacing or repairing any items beyond its control.
In all cases, the use of other than APW Wyott Authorized OEM Replacement Parts will void this warranty.
This equipment is intended for commercial use only. Warranty is void if equipment is installed in other than commercial application.
Water Quality Requirements
Water supply intended for a unit that has in excess of 3.0 grains of hardness per gallon (GPG) must be treated or softened before being
used. Water containing over 3.0 GPG will decrease the efficiency and reduce the operation life of the unit.
Note: Product failure caused by liming or sediment buildup is not covered under warranty.
"THE FOREGOING WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSES AND
CONSTITUTES THE ENTIRE LIABILITY OF APW WYOTT. IN NO EVENT DOES THE LIMITED WARRANTY EXTEND
BEYOND THE TERMS STATED HEREIN."
9/05
16
Download PDF