EverFocus | EPN4122 | NVR Device Pack Release Note

NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v2.6.0 (2012/10/19)
Modules:
Device Pack
v 2.6.0
Supported Systems:
Mainconsole
v 3.5.0 above
NVRmini 2
v 1.5.0 above
Titan NVR
v 1.3.0 above
New Camera Supported:
Axis
M1014,M1034-W, M1143-L, M1144-L, M3004, M3005, M7010, M7014, P5544,
P7224, Q7406, Q7414 and Q7424-R
D-Link
DCS-2130 (Titan/Mini2 support and Mainconsole already support on v2.5) and
DCS-3716
Everfocus
EDN3160, EDN3260, EDN3340, EHN3160, EHN3260, EHN3340 and EPN4122
Forenix
ACD-3VM501 and NPB-720BM
Jetstor
JS-C1100, JS-C2100, JS-WGP-100-CB, JS-B0100, JS-B0100-W, JS-B0131,
JS-BB1100-R30, JS-B1100, JB-B1204-R25, JS-D0100, JS-D1100, JS-D1130,
JS-D1204, JS-ISD0200x18 and JS-OSD0200x20
Levelone
FCS-3071-V2
Samsung
SNP-6200, SNP-6200H, SNP-6200HP, SNP-6200P
Shany
SNC-21XX ( SNC-WD2112MDN, SNC-WD2122DN, SNC-WDL2132DN,
SNC-WDL2142DN)
SNC-22XX ( SNC-2212MDN, SNC-2222DN, SNC-L2232DN)
SNC-23XX (SNC-WD2312MDN, SNC-WD2322DN, SNC-WDL2132DN,
SNC-WDL2332DN)
Sunell
IPS54/70DN/Z18, IPS54/70DN/ZR18, IPS54/70DR/Z18, IPS54/70DR/ZR18,
SN-IPC54/11FDN, SN-IPC54/11DN, SN-IPC54/11EDN, SN-IPV54/11DN,
SN-IPV54/11DR, SN-IPD54/11VDN, SN-IPD54/11VDR, SN-IPV54/11UDN,
SN-IPV54/11UDR, SN-IPR54/11DN, SN-IPR54/11ANDN, SN-IPV54/11ZDR,
SN-IPR54/11ALDN, SN-IPR54/11AKDN, SN-IPD54/12VDN, SN-IPC54/12DN,
SN-IPC54/12EDN, SN-IPC54/12FDN, SN-IPV54/12DN, SN-IPV54/12DR,
SN-IPD54/12VDR, SN-IPV54/12UDN, SN-IPV54/12UDR, SN-IPR54/12DN,
SN-IPR54/12ANDN, SN-IPV54/12ZDR, SN-IPR54/12ALDN, SN-IPR54/12AKDN
and VSR54/01
Techson
TCIP-220MDN, TCIP-230WDRMDN, TCIP-213WDRMDN, TCIP-D213WDRDN
1 / 38
1
NVR Device Pack Release Note
NUUO version 2.6.0
TCIP-D220DN, TCIP-D230WDRDN, TCIP-LD213WDRMDN, TCIP-LD220MDN,
TCIP-LD230WDRMDN and TCIP-LPro213WDRMDN (Mini2 and Titan support,
Mainconsole already support on DP v2.5)
Zavio
D5113, D7111, F1100 and F1105
Digital WatchDog
DWC-MPA20M
Notice:
1.
Known issue:
a. Sunell
SN-IPD54/12VDN,
VSR54/01
autodetect
fail
due
to
camera
FW
issue.
IPS54/70DN/ZR18 VSR54/01 changing MJPEG resolution may get Fail message due to
camera FW issue. Can’t support G711 A-law(Onvif issue)
b. Axis P7224 can’t use second audio in (All). Support G.711 only (mini2/Titan).
c. Forenix NPB-720BM doesn’t support On-edge motion under TCP or UDP protocol.
d. Digital WatchDog DWC-MPA20M does not support On-edge motion detection.
e. Digital WatchDog DWC-MPA20M, if switching between profiles constantly(about 5~10
times), sometimes the camera is just disconnected and no longer connected again until
rebooting it
f.
2.5 and 12.5 framerate can’t be show at EPN4122.
Bug fixed:
Mainconsole:
-
Can’t connect over 3 Pelco IP110 devices.
-
Probe connection failed after several minute.
Icantek icanview240 can’t use PTZ.
EverFocus ONVIF camera responses LAN address in NAT environment.
NVRmini 2:
-
Panasonic WV-SW395 PTZ speed moving angle too much.
-
Vivotek some PTZ models can’t control PTZ when PTZ speed is 0 in the camera web interface.
Probe connection failed after several minute.
EverFocus ONVIF camera responses LAN address in NAT environment.
Titan NVR:
-
Panasonic WV-SW395 PTZ speed moving angle too much.
-
Vivotek some PTZ models can’t control PTZ when PTZ speed is 0 in the camera web interface.
Probe connection failed after several minute.
EverFocus ONVIF camera responses LAN address in NAT environment.
2 / 38
2
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v2.5.0 (2012/09/18)
Modules:
Device Pack
v 2.5.0
Supported Systems:
Mainconsole
v 3.5.0 above
NVRmini 2
v 1.5.0 above
Titan NVR
v 1.3.0 above
New Camera Supported:
ACTi
KCM5611 and KCM7911
Axis
Q1604 and Axis (for IP camera and video servers’ Video only)
Dahua
SD65XX-HN and SD69XX-HN
D-Link
DCS-2130 (Mainconsole only)
Ernitec
Mercury SX 302, Mercury SX 302IR, Mercury SX 302M, Orion SX 802IH, Orion SX
802OPH, SX 605, Vega SX 102 and Vega SX 102IH
Guardeon
GDN-V1300D, GDN-DV1300IR and GDN-D1300IR
Honeywell
HCD5MIH, HD3MDIH and HD4MDIH
JVC
VN-H257U, VN-H257VPU, VN-H37U, VN-V685U, VN-V686BU and
VN-V686WPBU(Mainconsole only)
LG
LNB3100, LNB5100, LND3100, LND5100, LNP2800, LNP2800I, LNP3700, LNP3700T,
LNV5100, LNV5110, LW130W, LW332, LW335, LW342, LW345, LW6324, LW6354,
LW6424, LW6454 and LW9422
Vivotek
FE8171V (Mainconsole only and Titan/Mini2 already support on v1.13) and FE8172V
3 / 38
3
NVR Device Pack Release Note
NUUO version 2.6.0
Notice:
2.
Known issue:
a. ACTi KCM5611 does not support RS-485 (not support Pan/Tilt).
b. Dahua SD65XX-HN, SD69XX-HN does not support motion detection at MJPEG.
MJPEG bitrate can’t set over 8192 kbps.
c. Axis Generic support video only.
d. Axis Q1604 does not support AAC at MJPEG and not support H264 CBR mode.
e. Guardeon does not support audio in with 16KHz sampling rate.
f. LG series can’t support dual-stream when video parameter is H264, 1920x1080(or above),
over 20fps.
g. LG Speed Dome models (LW9422, LNP3700T) PTZ will stop automatically when press bottom
over 10 sec. Focus near/far needs to setup the focus mode in camera’s OSD. Adjust zoom
speed is useless.
i. Vivotek FE8172V, not support CBR mode. Not support audio at MJPEG. Not support AAC
audio.When resolution is 1360x786, video stream would have a white line at the left-bottom
of the frame. If set to Full HD mode, the low profile video stream would have a color line at
the bottom of frame.
Bug fixed:
Mainconsole:
-
Fix Santec SNC-8322 PTZ “down-left “
Fix Dynacolor NV053, NV223 autofocus
Probe PIC-H2010 with wrong MAX framerate support.
Zavio B7210, F7210 with wrong resolution support.
NVRmini 2:
-
Panasonic WV-SC385 can’t get preset point.
Sunell SN-IPS54/60DN/Z18/WI Motion Detection failed after 60sec.
Titan NVR:
-
Panasonic WV-SC385 can’t get preset point.
Sunell SN-IPS54/60DN/Z18/WI Motion Detection failed after 60sec.
4 / 38
4
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v2.4.0 (2012/08/20)
Modules:
Device Pack
v 2.4.0
Supported Systems:
Mainconsole
v 3.5.0 above
NVRmini 2
v 1.5.0 above
Titan NVR
v 1.3.0 above
New Camera Supported:
ACTi
TCM1111, TCM3111, TCM4511, TCM5111 and TCM6630
Alphatech
AT-IMF5736 and AT-IMV5756
Brickcom
30xN
Grundig
GCI-K1526V and GCI-K1812W
Probe
PIC-2010T and PIN-H1310
Sunell
SN-IPS54/60DN/Z18/WI
Techson
TCIP-213WDRMDN, TCIP-220MDN, TCIP-230WDRMDN, TCIP-D213WDRDN,
TCIP-D220DN, TCIP-D230WDRDN, TCIP-LD213WDRMDN, TCIP-LD220MDN,
TCIP-LD230WDRMDN and TCIP-LPro213WDRMDN (Mainconsole only)
Videosec
ICS-20W, ID-20, IRD-20 and IRW-20W
Vivotek
BB5116, BB5315, BD5115 and FD8131
3Svision
N3071, N6072, N6073, N6074, N6075, N6076, N6077 and N9071
5 / 38
5
NVR Device Pack Release Note
NUUO version 2.6.0
Notice:
3.
Known issue:
a. ACTi TCM6630, DI/DO useless, FW issue.
b. AlphaTech models, 2nd profile's framerate will be limited to 15fps when 1st profile set
resolution to 1600x1200. Framerate only support 3~25fps.
c. Brickcom 30xN, Cover FB-300Np, WFB-300Np, MD-300Np. MD-300Np is no support DI/DO
and one way audio only.
d. Grundig models, camera become slow response (or not response) when set resolution,
compression and framerate near the maximum value, audio will not smooth at the same
time. Suggest modify GOV length to small value when video framerate lower than 5.
e. Probe series, will access failed when add more than 1 channel to the same camera.
f. Sunnell SN-IPS54/60DN/Z18/WI, dual-stream will connect failed when camera is too busy.
4.
Bug fixed:
Mainconsole:
- Brickcom VS-04A, can’t be selected in the camera support list.
NVRmini 2:
-
ACTi CAM6610, adjust PTZ speed to adequate speed.
-
Grundig C3075, increase the PTZ control latency.
-
Sunnell camera can’t disconnect automatically when press disconnect button.
Titan NVR:
-
ACTi CAM6610, adjust PTZ speed to adequate speed.
-
Grundig C3075, increase the PTZ control latency.
-
Sunnell camera can’t disconnect automatically when press disconnect button.
6 / 38
6
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v2.3.0 (2012/07/18)
Modules:
Device Pack
v 2.3.0
Supported Systems:
Mainconsole
v 3.5.0 above
NVRmini 2
v 1.5.0 above
Titan NVR
v 1.3.0 above
New Camera Supported:
Alphatech
AT-IMF5739 and AT-IMF5750
Basler
BIP2-D1920c-DN
Dynacolor
na063
Mobotix
M24M-Sec
Santec
SNC-3322 and SNC-8322I/HO
Telview
IPB612P-ICR, IPB630P-ICR, IPD612-VP-VF-IR, IPD630-VP-VF-IR, IPE600, IPW612,
IPW630, IPW630P, IPZ611, VIS611, VIS614 and VIT621
Vivotek
FD8335H, FD8372 and IP8361
7 / 38
7
NVR Device Pack Release Note
NUUO version 2.6.0
Notice:
5.
Known issue:
a.Alphatech AT-IMF5739, AT-IMF5750
2nd profile's framerate will be limited to 15fps when 1st profile set resolution to 1600x1200.
Framerate only support 3~25fps.
b.Basler BIP2-D1920c-DN
Not support Audio & Talk
c.Dynacolor na063
Video parameter can't sync with camera web interface, need to refresh the browser.
Talk quality is not clear.
Camera efficiency will done when set high resolution & quality stream.
d.Mobotix M24-Sec
Audio only support on MxPEG.
Motion event works abnormal until first time trigger.
Resolution of dual-stream can't bigger then main-stream.
e.Vivotek FD8372
Mpeg4 support first 2 maximum resolutions are 1920x1920 & 1920x1536.
6. Bug fixed:
Mainconsole:
- Etrovision EV8180U black video when set resolution to 1920x1080.
NVRmini 2:
-
CNB IDC4050IR, IDC4050F dualstream doesn’t work.
Titan NVR:
-
CNB IDC4050IR, IDC4050F dualstream doesn’t work.
8 / 38
8
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v2.2.1 (2012/07/05)
Modules:
Device Pack
v 2.2.1
Supported Systems:
Mainconsole
v 3.5.0 above
NVRmini 2
v 1.5.0 above
Titan NVR
v 1.3.0 above
Notice:
1. Bug fixed:
For Eneo GCD1710M-IR, please remove DP v2.2.0 first then install DP v2.2.1 and reset
Mainconsole:
a. Eneo camera model correct to GXD-1710M-IR
b. Axis P7210 can not view the correct video channels with Codec H264.
NVRmini 2:
a. Eneo camera model correct to GXD-1710M-IR
Titan NVR:
a. Eneo camera model correct to GXD-1710M-IR
9 / 38
9
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v2.2.0 (2012/06/19)
Modules:
Device Pack
v 2.2.0
Supported Systems:
Mainconsole
v 3.5.0 above
NVRmini 2
v 1.5.0 above
Titan NVR
v 1.3.0 above
New Camera Supported:
ACTi
KCM-3311 and KCM-7311
Arecont
AV2116 and AV3116
Axis
M7014, P3354, Q1604, Q7414 (NVRmini 2, Titan NVR only)
P3364
Brickcom
OB-100Ap, VS01A, PZ-040D and PZ040E
Eneo
GXB-1710M-IR, GXC-1710M and GCD-1710M-IR
Hikvision
DS-2CD7153-E
Mobotix
D-14D Sec
Samsung
SNB-1001, SND-1011, SND-1080, SNO-1080R, SNV-1080 and SNV-1080R
Vivotek
FD8372, FD8136, IP8133, PT8133, SD8362
10 / 38
10
NVR Device Pack Release Note
NUUO version 2.6.0
Notice:
1. Known issue:
a. Hikvision DS-2CD7513-E
this camera can not set framerate 15~22 when resolution is 1600x1200,1600x912.
sometimes camera can't set resolution 1600*1200、1600*912、1280*960.
2.
Bug fixed:
Mainconsole:
b. ACTi KCM-5211 PTZ function will be useless after 1 week. (Need upgrade FW V5.05.07 & ISP
V1.02.02)
c. Samsung SND-3080 can not get the parameter of the video stream.
NVRmini 2:
None
Titan NVR:
a.
Axis Q7406 can not support PTZ control.
b.
Axis P7210 can not view the correct video channels with Codec H264.
c.
UDP IPE3500M disconnect automatically after 24hours.
d.
Vivotek SD83x2, SD83x3 can not adjust the PTZ speed.
e.
Zavio B7201 video broken in LiveView.
11 / 38
11
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v2.1.0 (2012/05/21)
Modules:
Device Pack
v 2.1.0
Supported Systems:
Mainconsole
v 3.5.0 above
NVRmini 2
v 1.5.0 above
Titan NVR
v 1.3.0 above
New Camera Supported:
Axis
P3367, P7210, P7214, P8513, P8514, Q1602, Q1602-E, Q1922 and Q1922
Brickcom
130N series and 50xA series
CNB
IDC4000T
COP
15-WS01D-E
Guardliner
SPmicro-412
Hikvision
DS-2CD853F-E
Panasonic
WV-SC386, WV-SP508, WV-SP509, WV-ST162. WV-ST165, WV-SW172,
WV-SW174W, WV-SW175, WV-SW314, WV-SW316/L, WV-SW558 and WV-SW559
Samsung
SNP-3302/H
Santec
SNC-3342 and SNC-6332
Vision Hi-Tech
I series, Mi series, M3i series and NVS102
Vivotek
FD8134-SS, IP7160-SS, IP7161-SS, IP8151-SS, IP8161-SS, IP8162P-SS,
IP8332-SS, SD8121-SS, SD8362E, SD8362-SS, SD8323E-SS
3SVision
N3072, N5071 and N8072
12 / 38
12
NVR Device Pack Release Note
NUUO version 2.6.0
Notice:
3.
4.
Known issue:
a. Brickcom 130N series need waiting 15s to finish adjust the zoom/focus.
b. Brickcom 50xA series need waiting a period of time to reconnect stream success when switch
the video resolution higher than 1920x1080.
c. Hikvision DS-2CD853F-E can't set framerate 15~22 in Max resolution.
Bug fixed:
Mainconsole:
Fixed Sony SNT-V704 can’t connect failed.
Fixed UDP camera image gray out or break randomly when config different resolutions.
NVRmini 2:
Fixed Axis M7001 can’t use daulstream.
Titan NVR:
None
13 / 38
13
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v2.0.0 (2012/04/18)
Modules:
Device Pack
v 2.0.0
Supported Systems:
Mainconsole
v 3.5.0 above
NVRmini 2
v 1.5.0 above
Titan NVR
v 1.3.0 above
New Camera Supported:
ACTi
KCM-3211, KCM-3911
Arecont
AV20185CO, AV20365CO, D4F series
Axis
M3113-R, M3113-VE, Q6032
Bullwark
BLW-230MP-BS, BLW-230MP-DS, BLW-IN220X-S, BLW-IR230MP-DSM,
BLW-IR230MP-SM and BLW-OUT220X-S
Centrix
B13H, C10, C10-W, D13HD, W13H
Dynacolor
NH720-20N1, NH820-20N1, nv103, nv223, nv053 and nv063
Forenix
B0202
GE
TVC-MP2B-S
Hikvision
DS-2CD754F-EI, DS-2CD8254F-EIS, DS-2CD752MF-E, DS-2CD754F-E
DS-2CD854F-E and DS-2CD883F-E
IQinvision
IQeye863N, IQeye865N, IQM30N, IQM31N, IQM32N and IQD32S
Levelone
FCS-0071, FCS-1122, FCS-5061 and WCS-0050(Mainconsole only)
Panasonic
WV-SC384, WV-SC385, WV-SF332, WV-SF335E, WV-SW355(above add I/O),
WV-SW396
Rover
RV1WAD, RV01AD, RV01AT, RV04AD, RV1WAG, RV79AD, RV7RAD, RV7RAG,
RV81AD, RV81AG, RV84AD, RV84AM, RV84AV and RV87ZA
Samsung
SNB-3002, SNO-7080RP, SNP-3371, SNP-3371TH, SPE-400
SND-3082 (F) and SNV-3082
Vivotek
FD8135H, FD8335H, IP8335H, PT8133 and PT8133W
Zavio
B7210, D7110, F1100(Mainconsole only), F1105(Mainconsole only), F3101, F3106,
F3201, F3206 and F531E
14 / 38
14
NVR Device Pack Release Note
NUUO version 2.6.0
Notice:
5. From DP v2.0, Mainconsole/NVRmini 2 (from v1.5)/Titan NVR (from v1.3) share same
device pack.
6.
Known issue:
a.
ACTi : KCM3211's PTZ only support Zoom and Focus.
b. Arecont: AV20185 include AV20185DN, AV20185CO, AV20365 include AV20365DN,
AV20365CO
c.
Bullwark: BLW-IR230MP-SM 1920x1080 MJPEG Bit rate too high will affect camera
parameter can not sync to camera information
d. Forenix: not support search and auto detected (camera FW issue)
e. Hikvision: 1.DS-2CD8254F-EIS、DS-2CD854F-E、DS-2CD883F-E can't set framerate 15~22
in Max resolution, DS-2CD8254F-EIS、DS-2CD854F-E、DS-2CD883F-E image
broken when resolution over 1600x1200
f. IQinvision: IQM3xN series not support audio in M-JPEG
g. Panasonic: WV-SC385 and WV-396 support continuous PTZ
h. Samsung: SNP-3301, SNP-3370: H264 can't support QCIF resolution
7.
Bug fixed:
Mainconsole:
a. Fix Vivotek IP7361 motion detection works failed when set motion area more than 2.
b. Santec: SNC-4302
1080P and 800x600 don’t support flip and rotate, Model I/O revise and Quality setting fail
issue
NVRmini 2:
a. Fix AV8185DN can't get correct video framerate, quality & compression after setting video
parameter when adding the same model with a server over two times.
Titan NVR:
a. Fix Panasonic WV-SC385. The speed of PTZ is very slow in the Titan NVR.
15 / 38
15
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.19.0 (2012/02/29)
Modules:
Device Pack
v 1.19.0
Supported Systems:
MainConsole
v 3.3.0 above
New Camera Supported:
Dynacolor:
V2 series
iCANTEK:
iCanView322MP, iCanView340MP
Messoa:
NIC990PRO-HP
Micronet:
SP5523W, SP5563HTM, SP5581HDC, SP5582HTM, SP-5584HTM, SP5591HTM
SP5923,
Pelco:
IP110, SpectraIV-IP
Santec:
SNC-3302, SNC-4302, SNC-5312IR, SNC-6302, SNC-6312IRH, SVS-3001
Truen:
TCAM-5x10, TCS-2000
Notice:
c.
d.
Firmware Upgrade

iCANTEK: iCanView332MP, iCanView362MP

Truen: TCAM-570
Known issue:
i. Messoa: NIC990PRO-HP
Only support video and PTZ. Other parameters setting, audio and DI/DO are not available
due to firmware issue.
j. Pelco : IP110, SpectraIV-IP
Only support MPEG4 image, not support parameter setting. SpectraIV-IP only support
704x240. IP110 only support 704x480.
k. Micronet: SP5923
1080P and 800x600 don’t support flip and rotate.
l. Micronet: SP5581HDC
Not support talk.
m. Santec: SNC-4302
1080P and 800x600 don’t support flip and rotate.
n.
Truen: TCAM-570
16 / 38
16
NVR Device Pack Release Note
NUUO version 2.6.0
MJPEG not support audio.
o.
Truen: TCAM-2000

Not support below resolutions:
Composite NTSC 352x240, 720x240
HDMI 1080i60 352x240, 720x240, 640x360

e.
Echo would occur after stop talk function
Bug fixed:
a. ACTi: KCM-5211 Auto-Focus behavior did not sync with camera web.
b. Vivotek: VS8401 would connect with incorrect channels.
c. CNB: ISS2965x can’t Zoom In/Out by joystick.
d. Corumcctv: MainConsole would hang and stop after disconnecting the video stream.
17 / 38
17
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.18.0 (2012/01/03)
Modules:
Device Pack
v 1.18.0
Supported Systems:
MainConsole
v 3.3.0 above
New Camera Supported:
Hikvision:
DS-2CD783F-E, DS-2CD783F-EI, DS-2DF1-5702, DS-2DF1-570A,
DS-2DF1-5732, DS-2DF1-573A, DS-2DF1-57A
Lilin:
IPD2220ES, IPG1022ES, IPR320ESX, IPR722S, IPR7424/8ESX
Sony:
SNC-EP521, SNC-EP550, SNC-EP580, SNC-ER550
Vision Hi-Tech:
VISION i series, VISION M3i series, VISION NVS102
Vivotek:
IP8335H
Notice:
f.
Bug fixed
p.
PELCO: D5118 cannot operate PTZ feature by joystick.
q.
PELCO’s cameras: The video format does not sync with web’s setting.
r.
Fine: TCP-690 cannot be connected.
s.
AXIS: P5534-E cannot set PTZ preset positions.
t.
iCANTEK: iCanView362MP, iCanView332MP :
The audio stream would cause IP+ crash.
g.
Known issue:

Lilin: IPG1022ES, IPD2022ES and IPR7424/8ESX
The audio inputs only support HTTP protocol.

Hikvision: DS-2DF1-57xx series
The H.264 stream displays not smoothly.
18 / 38
18
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.17.0 (2011/12/01)
Modules:
Device Pack
v 1.17.0
Supported Systems:
MainConsole
v 3.3.0 above
New Camera Supported:
ACTi:
KCM-5211E, KCM-5311E
AMTK:
AM2110D, AM2231D, AM2590D
Etrovision:
EV8281U, EV8285Q, EV8286Q
Hikvision:
DS-2CD753F-E, DS-2CD753F-EI, DS-2CD754F-E, DS-2CD754F-EI,
DS-2CD754FWD-E, DS-2CD754FWD-EI, DS-2DF1-572
Panasonic:
WV-SF132, WV-SF135, WV-SW152/M, WV-SW155/M
UDP:
IPE1100M, IPE3100, IPE3500, IPE4100, IPE5500, IPE6500, IPE7500
Vision Hi-Tech:
Vision Mi series
Vivotek:
MD7560X
Zavio:
F3201, F7210
Notice:
h.
Bug fixed
u.
Mainconsole breakdown when closing and restarting Mainconsole after Onvif models operate
Start patrol.
v.
SAE-E588HDE18C can’t control Zoom In/Out by joystick.
w.
PELCO-D5118 doesn’t store the relative parameter of ptz speed after change it and restart
Mainconsole.
i.
Known issue:

Hikvision DS-2CD753-E, DS-2CD753-EI, DS-2CD754-E, DS-2CD754-EI,
DS-2CD754FWD-E, DS-2CD754FWD-EI do not support PTZ preset using RS-485.
j.
Firmware Upgrade:

Arecont: AV3135

Samsung: SNB-5000, SND-5080/F, SNP-5200H, SNV-5010, SNZ-5200
19 / 38
19
NVR Device Pack Release Note
NUUO version 2.6.0

UDP: NVC1000
Release Version v1.16.0 (2011/11/04)
Modules:
Device Pack
v 1.16.0
Supported Systems:
MainConsole
v 3.3.0 above
New Camera Supported:
Brickcom:
MD-100AP
CNB:
IDC4050F, IDC4050IR, IDC4050VF, IDC4050VR, IGC2050F, ISMC1063x,
IS1765x, ISS2965x, ISSM2063x, IVC5055VF, IVC5055VR, IXC2050IR,
Dahua:
HDB3300N, HDB3300P, HDBW3300N, HDBW3300P, HF3110N, HF3110P,
HF3211P, HF3300N, HF3300N-W, HF3300P, HF3300P-W
Etrovision:
EV3150A, EV3151, EV3151A, EV6150A-BI, EV6150A-CI, EV6151A, EV6153A,
EV6156A, EV6250A-EI/EO, EV6251A-FI/FO, EV6252A-GI/GO, EV6252A-GI/GO,
EV6353A-DO, EV6353A-EO, EV6353A-FO, EV6355A/AP-BO, EV6355A/AP-CO,
EV6551A/AP-BI, EV6551A/AP-CI, EV6551A/AP-DI, EV6552A/AP, EV6552R/RP,
EV6580A/AP-B/C, EV6581A/AP, EV6750, EV8150A, EV8180A, EV8180A-D,
EV8180F, EV8180Q, EV8180Q-D, EV8180U, EV8180U-D, EV8280U, EV8285U,
EV8383F, EV8580A-B, EV8580A-C, EV8580A-DB, EV8580A-DC, EV8580F,
EV8580Q-C, EV8580Q-DB, EV8580Q-DC, EV8580U-B, EV8580U-C, EV8580U-DB,
EV8580U-DC, EV8580U-DM, EV8580U-M, EV8581A-C, EV8581A-DB, EV8581A-DC,
EV8581Q-C, EV8581Q-DB, EV8581Q-DC, EV8581U-B, EV8581U-C, EV8581U-DB,
EV8581U-DC, EV8582A-D, EV8780A, EV8780U, EV8781A-C, EV8781A-DC,
EV8781F, EV8781Q-C, EV8781Q-DC, EV8781U-C, EV8781U-DC, EV8781U-DM,
EV8781U-M, EV8782A, EV8782A-DB, EV8782Q, EV8782Q-DB, EV8782U,
EV8782U-DB
Shany:
SNC-10XX, SNC-20XX, SNC-81XX, SNC-91XX, SNC-D1XX
USAG:
US-AVC4-2-600NR-I2
Vivotek:
IP8133W, IP8331, MD8562
Samsung:
SNV-7080, SNV-7080R
20 / 38
20
NVR Device Pack Release Note
NUUO version 2.6.0
Notice:
1. Bug fixed:

AXIS P1346: Support all of AAC audio codec setting.

Arecont AV2125: Fix the image would turn to green when using UDP connection

Shany: Fix 1080P resolution name.

Zavio D611E: Fix connection issue
2. Known issue:

CNB: 2M pixel models do not support UDP connection.

Dahua: All models only support Pan & Tilt feature using RS-485 to control the external
device.

Etrovision: xx8x/xx5x series do not support talk function, 8150A and related models do not
support VGA resolution.

USAG: Does not support PTZ feature using RS-485.

Samsung: 3120x, 3430H, 5xxx and 7xxx series only support TCP connection.
3. Firmware Upgrade:

Samsung: SND-7080, SNO-5080R, SNP-3120, SNP-3120V, SNP-3430H, SNV-3120,
SNV-5080R
21 / 38
21
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.15.0 (2011/10/03)
Modules:
Device Pack
v 1.15.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1 & 3.5.0 & 3.5.10 &
v 3.5.18
New Camera Supported:
Arecont:
AV20185DN, AV20365DN
Probe:
PIC-500, PIC-501, PIC-H1310T, PIC-H2010T, PID-500, PID-501, PID-H1000,
PID-H2010T, PIK-H2010T, PIN-H1310T, PIN-H2010T, PIP-H1000, PIS-400,
PK-H1310T, PMI-400, PMI-403, PMI-410, PMI-H2000, PTI-400, PTI-401, PTI-402,
PTI-403, PTI-500, PTI-501, PTI-502, PTI-503, PTI-H1302, PTI-H2100
Shany:
SNC-21X0, SNC-21XX, SNC-22XX, SNC-23XX, SNC-HD2XX, SNC-HD81X2,
SNC-HD91X2, SNC-HD91XX, SNC-RX01N
Vivotek:
SD83x1E, SD83x2E, SD83x3E, VS8401
Zavio:
F3106, F7110
Notice:
4. New feature:

Onvif 1.02 PTZ feature is supported.
5. Bug fixed:

LevelOne FCS-5041: login in with wrong password will cause system crash.
6. Known issue:
7. Probe series don’t support IO feature/audio in.
8. Shany series will show B/W image when set camera parameter very low quality in MJPEG codec.
22 / 38
22
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.14.0 (2011/09/02)
Modules:
Device Pack
v 1.14.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1 & 3.5.0
New Camera Supported:
ACTi:
KCM5211, KCM5311, KCM7211
Arecont:
AV1115, AV1125, AV2115, AV2125, AV3115, AV3125, AV5115, AV5125,
AV10115
AXIS:
M3114-VE, Q6035, Q6035-E
CORUM:
CS-190-IO, CS-190-IP, CS-190-IW, CS-265-IO, CS-265-IP, CS-265-IW,
CS-285-IP, CS-325-IO, CS-325-IP, CS-385-IO, CS-385-IP, CS-390-IO,
CS-390-IP, CS-410-IP, CS-410-IW, CS-415-IP, CS-415-IW
Forenix:
ACDV-3VM501, AEP-Q2018H-IP, AEP-Q2018HW-IP, AEP-Q2026H-IP,
AEP-Q2026HW-IP, AEP-Q2036H-IP, AEP-Q2036HW-IP, ASP-PTIR737-IP,
ASP-PTIR737-LA-IP, ATCP-IRH5030C, ATCP-IRH5040C, ATCP-MH802,
ATCP-MH802DN, ATCP-MH802DN/WI, ATCP-MH802WI, ATCP-VM501,
B0100, B1100, C1100, C1100-W, D0100, D1100, D2100
Messoa:
NIC910HPRO, NIC930HPRO, NIC950HPRO
SONY:
SNC-EP520, SNC-ER520, SNC-ER521, SNC-ER580
UDP:
IPE3500M, NVC4000, NVC4000-R12, NVC4000-R40
Vivotek:
IP8352, PZ81x1, PZ81x1W
Notice:
9. New feature:

Onvif 1.02 support is officially released on Device Pack 1.14.0 but non-support PTZ feature.

ACTi
TCD2500 supports PTZ feature.

Grandstream
GXV series supports talk and PTZ features
23 / 38
23
NVR Device Pack Release Note
NUUO version 2.6.0
10. Bug fixed:

PANASONIC WV-NM100 has probabilities cause system crash.

ACTi ACM1431 Audio disabled issue.
Release Version v1.13.0 (2011/08/02)
Modules:
Device Pack
v 1.13.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1 & 3.5.0
New Camera Supported:
ACTi:
KCM7111
AXIS:
M5013, M5014, P5512, P5512-E, P5522, P5522-E
Brickcom:
VS-04A
Everfocus:
EQN2200, EQN2201
Grandstream:
GXV-3501, GXV-3504, GXV-3601, GXV-3601HD, GXV-3601LL, GXV-3611HD,
GXV-3611LL, GXV-3615, GXV-3651, GXV-3662HD
Panasonic:
WV-SW352, WV-SW355
Pelco:
D-5118
Samsung:
SNP-3301, SNB-7000
Vivotek:
FE8171V
Notice:
11. New feature:

AXIS
P1346, P5534 support AAC codec

Vivotek
VS8102 supports continuous PTZ
12. Bug fixed:

Truen
Adjust TCAM-570 PTZ moving distance sync with web client.

SAE
DR-E588-HD18 can’t control PTZ by joystick.

AXIS
Supported Q7401 to 64 preset point.
24 / 38
24
NVR Device Pack Release Note
NUUO version 2.6.0

Fine
MainConsole will hang out when single TCP-VM501 setup four connections at the same time.
Release Version v1.12.0 (2011/07/01)
Modules:
Device Pack
v 1.12.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1 & 3.5.0
New Camera Supported:
Everfocus:
EAN3200, EHN3200, EDN3240, EZN3240
Samsung:
SNB-1000, SND-7080, SNO-5080R, SNP-3120V, SNP-3370, SNP-3430H,
SNP-5200, SNP-5200H, SNV-5010, SNV-5080R, SNZ-5200
VIVOTEK:
FD8162, FD8361L, FD8362, FD8362E, SD8362E
Notice:
13. Bug fixed:

Fix Sony preset name length issue.

Fix Panasonic WV-SP105 auto detect failure.
25 / 38
25
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.11.0 (2011/05/31)
Modules:
Device Pack
v 1.11.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1 & 3.5.0
New Camera Supported:
ACTi:
KCM5111, TCM4001
AXIS:
P3346, P3346-V, P3346-VE
CTCunion:
DVS-8501E, DVS-8504E
Panasonic:
DG-SF334, WV-SF342, WV-SF346
Samsung:
SNB-5000, SND-5080/F, SNV-3120, SNV-5080
Santec:
SNC-3903M, SNC-5321MIR, SNC-6163ID, SNC-6223MIR, SNC-6303M,
SNC-P3603M
Sony:
SNC-DH110/B, SNC-DH110/W, SNC-DH110T/B, SNC-DH110T/W
Videosec:
ICS-13, ICS-20F, ID-20
VIVOTEK:
IP8362, MD7530, VS8801
UDP:
NVC1000
Notice:
1. Bug fixed:

Fix Dallmeier preset function dump

ONVIF check startcode if using RTSP for H264 codec

Fix Vivotek IP 7133 can’t use AAC codec issue
Release Version v1.10.0 (2011/04/15)
Modules:
Device Pack
v 1.10.0
Supported Systems:
26 / 38
26
NVR Device Pack Release Note
NUUO version 2.6.0
MainConsole
v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1
New Camera Supported:
Arecont:
AV1325, AV2825, AV8185DN, AV8365DN
AXIS:
P1347, P1347-E, P5532, P5532-E, P5534-E, Q1921, Q1921-E
D-link:
DCS-6511, DCS-7410
Fine:
EDH-02H, SP-PTIR737-LA-IP, TCP-IR590-WD30, TCP-IR590-WD50,
TCP-IRH5030C, TCP-IRH5040C
IQinvision:
IQ732N
Panasonic:
WV-SC384, WV-SC385, WV-SW395
Sony:
SNC-DH210/B, SNC-DH210/W, SNC-DH220, SNC-DH220T
vForge:
VFA1
VIVOTEK:
FD8133V, FD8134V, IP8151P, IP8162, IP8162P, MD7560
Notice:
1. Bug fixed:

ACTi CAM7301: auto detection failure issue.

Arecont Camera: auto detection failure issue.

Axis Q7401 sync preset point issue.

Dynacolor NH061: broken image issue (H.264/1280x720).
2. Bosch speed dome V4G series supported by Axis video server (test by model Q7404).
27 / 38
27
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.9.0 (2011/02/28)
Modules:
Device Pack
v 1.9.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4 & 3.4.1
New Camera Supported:
Arecont:
AV1315, AV2815
AXIS:
212 PTZ-V, 215 PTZ-E, 240Q Blade, 241Q Blade, 241S Blade, 243Q Blade, P1343-E,
P1344-E, P1346-E, Q1755-E, Q6034-E
Lilin:
IPS025, IPS030, IPS035, IPS125, IPS130, IPS135, IPS203, IPS212
Panasonic:
WV-SP102, WV-SP105
Sony:
SNC-CH260, SNC-CH280, SNC-DH210T/B, SNC-DH210T/W, SNC-DH260,
SNC-DH280
Notice:
1. Dallmeier DDZ40SM-HD: Add TCP connection, DI/DO and two-way audio.
2. Bug fixed: Panasonic WV-NS202A auto detection failure.
28 / 38
28
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.8.0 (2010/12/31)
Modules:
Device Pack
v 1.8.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4
New Camera Supported:
ACTi:
TCM7811,
Hikvision:
DS-2CD7133-E, DS-2CD7153-E
Levelone:
FCS-0040, FCS-3081, FCS-5051, FCS-5041, WCS-0040
Lilin:
IPD112ESX, IPD552EX, IPR414ESX, IPR418ESX, IPR454, IPR458
Sony:
SNC-CH110/B, SNC-CH110/S, SNC-CH220
Notice:
1. Bug fixed: Users can adjust Arecont camera’s resolution by setting four video coordinate
values. (Not support Arecont 8000 series cameras.)
29 / 38
29
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.7.0 (2010/11/12)
Modules:
Device Pack
v 1.7.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2 & v 3.3.12 & v 3.4
New Camera Supported:
ACTi:
ACM5811, ACM7511, TCD2100, TCM3001, TCM3011, TCM3401, TCM3411,
TCM4201, TCM5001, TCM7011
ARM:
MP13DDNWD, MP13VPDN
Camtron:
IPH3611N, NVE1000A, NVE2000A, NVE4000A
CryptoTelecom: S-152
Dallmeier:
DDZ40SM-HD
Panasonic:
BL-C210, BL-C230, WJ-GXE500, WV-SF332, WV-SF335, WV-SF336, WV-SP302,
WV-SP305, WV-SP306
Samsung:
SNS-100
Sony:
SNC-CH120, SNC-CH160, SNC-CH210/B, SNC-CH210/S, SNC-DH120,
SNC-DH120T, SNC-DH140T, SNC-DH160, SNC-DH240T
Truen:
TCAM-570
VIVOTEK:
FD8133, FD8134, IP8132, IP8151, IP8330, IP8332, PZ7132, SD81X1
Notice:
1. Bug fixed: Panasonic WV-NP502 won't show error message when switching video codec to
H.264.
30 / 38
30
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.6.0 (2010/10/7)
Modules:
Device Pack
v 1.6.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2 & v 3.3.12
New Camera Supported:
Arecont:
AV2805
Camtron:
CMNC-130, CMNC-200, CTNC-5358D, HLC-81A D/P, HLC-83V, HLC-83V/W
HLC-84V, HLC-84V/W
Honeywell:
ACUIX, HCD554IP, HD3MDIP, HD4DIP, HD4MDIP, HNVE1
PELCO:
IX10
Pixord:
P600, P606, PB630, PD634, PL621, PV6901
SAE:
ANNA 200M, E588HDE18C, E688HDE10
Notice:
1. Bug fixed: Fine WB-8211SDU can use PTZ function.
31 / 38
31
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.5.0 (2010/8/31)
Modules:
Device Pack
v 1.5.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2 & v3.3.11
New Camera Supported:
Brickcom:
CB-100A, CB-100Ae, FB-100A, FB-100Ae, FD-100Ae, WCB-100Ae,
WFB-100Ae
Fine:
CDV-3VM301, CDV-3VM501, CDV-3VWD960, CDV-3VWD960H, EP-601HW,
EP-908HW, EP-936HW, EP-HTQ935, EP-Q2018H-IP, EP-Q2018HW-IP,
EP-Q2026H-IP, EP-Q2026HW-IP, EP-Q2036H-IP, EP-Q2036HW-IP,
MD-D1612, SP-PTIR737-IP, TCMA-99, TCMP-99, TCP-IPWD690,
TCP-IPWD700DN, TCP-IRV540, TCP-IRV560/50M, TCP-MH802, TCP-VM201,
TCP-VM501, WB-H811, WB-H814
Hikvision:
DS-2CD702NF-E, DS-2CD702PF-E, DS-2CD712NF-E, DS-2CD712PF-E,
DS-2CD732F-E, DS-2CD792NF-E, DS-2CD792PF-E, DS-2CD802N-IR1,
DS-2CD802N-IR3, DS-2CD802N-IR5, DS-2CD802P-IR1, DS-2CD802P-IR3,
DS-2CD802P-IR5, DS-2CD832F, DS-2CD832F-E, DS-2DF1-401H,
DS-2DF1-402H, DS-2DF1-601H, DS-2DF1-602H, DS-2DF1-603H,
DS-2DF1-604H, DS-2DF1-605H, DS-2DF1-606H, DS-2DF1-607H,
DS-2DF1-611H, DS-2DF1-612H, DS-2DF1-613H, DS-2DF1-614H,
DS-2DF1-615H, DS-2DF1-616H, DS-2DF1-617H, DS-2DM1-602H,
DS-2DM1-603H, DS-2DM1-604H, DS-2DM1-612H, DS-2DM1-613H,
DS-2DM1-614H, DS-6101HFI-SATA, DS-6104HCI, DS-6104HCI-SATA
NetworkCamera: GE-100-CB, GP-100-CB, WGE-100-CB, WGP-100-CB
PELCO:
ID10, ID30, IDE20, IDS0, IE10, IE30, IEE10, IEE20, IES0, IMS0, IX30,
IXE20, IXS0
Sony:
SNC-RS44N, SNC-RS44P, SNC-RS46N, SNC-RS84N, SNC-RS84P,
SNC-RS86N, SNC-RS86P, SNT-EP104, SNT-EX101
Videosec:
IBF-211, ID-209, IDA-210, IP-206M, IS-240
Notice:
32 / 38
32
NVR Device Pack Release Note
NUUO version 2.6.0
1. Bug fixed: SANYO-HD5600P can change resolution.
2. Onvif supported: AXIS_P3301, Bosch_NWC-0455
Release Version v1.4.0 (2010/8/9)
Modules:
Device Pack
v 1.4.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2 & v 3.3.11
New Camera Supported:
iCanTek:
iCanView362MP, iCanView332MP, iCanView350MP, iCanServer612
SANTEC:
SNC-3901MDN, SNC-P3601M
33 / 38
33
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.3.0 (2010/7/21)
Modules:
Device Pack
v 1.3.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2
New Camera Supported:
ACTi:
TCM-1511
Arecont:
AV10005
AXIS:
M1103, M1113, M1054, Q6034
Panasonic:
BB-HCM547A, BB-HCM701
SANTEC:
SNC-6201M, SNC-5211MIR
Sony:
SNT-EX154, SNT-EX101E, SNT-EP154, SNC-CH140, SNC-DH140, SNC-CH180,
SNC-CH240, SNC-DH240, SNC-RH164, SNC-RS46P
Notice:
1. Sony SNC-CH240, SNC-DH240 do not support resolution over 1920x1080
34 / 38
34
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.2.0 (2010/6/8)
Modules:
Device Pack
v 1.2.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2
New Features
1. Support Arecont I/O function
New Camera Supported:
ACTi:
ACM-3601, ACM-3603, ACM-3701, ACM-3703, ACM-4001
TCD-2500, TCM-4101, TCM-5312, TCM-1231, TCM-1232
TCM-5601, TCM-5611, TCM-3511, TCM-7411
Arecont:
AV3135, AV1310, AV2110, AV3110, AV5110
AXIS:
P1346, P5534, Q1910, Q1910-E, M1104, M1114
M3203, M3203-V, M3204, M3204-V, P3304, M7001
CNB:
IDC4000T, IVC4000T
IQeye:
IQ040S, IQ041S, IQ042S, IQD30S, IQD31S
IQD40S, IQD41S, IQD42S, IQ540S, IQ541S, IQ542S
Panasonic:
BB-HCM100, BB-HCM110, BB-HCM580, BL-C140A
Samsung:
SNB-2000, SNB-3000, SND-3080, SNV-3080
Sanyo:
VCC-HD2500, VCC-HD2500P
Sony:
SNT-EX104, SNC-DH180, SNC-RH124
StarDot:
SDH500BN, SDH500B, SDH300B, SDH130BN, SDH130B
SDH500VN, SDH500V, SDH300V, SDH130VN, SDH130V
Notice:
1. Bug Fixed: Fixed MainConsole unexpected crash issue with Mobotix Q24M-sec camera.
35 / 38
35
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.1.1 (2010/5/12)
Modules:
Device Pack
v 1.1.1
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2
New Camera Supported:
CNB:
IBE3815NVR, IBE3815PVR, IBE5810NCR, IBE5810PCR
IDP4000VD, IDP4000VR, IDP4030VR, IGP1000, IGP1030
IJB2000, INS2000, IPM3063N, IPM3063P, ISMC1063N, ISMC1063P
ISS2765NW, ISS2765PW, IVP4000VR, IVP4030VR
LevelOne:
FCS-7111
36 / 38
36
NVR Device Pack Release Note
NUUO version 2.6.0
Release Version v1.1.0 (2010/5/4)
Modules:
Device Pack
v 1.1.0
Supported Systems:
MainConsole
v 3.3.0 & v 3.3.2
New Camera Supported:
ACTi:
AMU-9401, AMU-9711, TMU-9811, TMU-9911
Bosch:
NW-455
Brickcom:
WCB-100A, WFB-100A, FD-100A
CISCO:
WVC210
Dynacolor:
nNH221, nNH061, V1, V6
Everfocus:
EAN-850A, EZN-850, EDN-800, EDN-850H, EAN900, EAN800AW, EAN800A
EVS200A, EVS200AW, EPN2700, EPN3100, EPN3600
LevelOne:
FCS-3031, FCS-3051, FCS-1131, FCS-1141, FCS-3071, FCS-0030, WCS-0030
FCS-1121, FCS-3061, FCS-4020, FCS-1040 v3.0, WCS-2040 v3.0, FCS-1151
MOBOTIX:
D24M-Basic, D24M-IT, D24M-Sec
Panasonic:
BB-HCM705A, BB-HCM715A, BB-HCM735A
Samsung:
SNP-3300A
SanTec:
SNC-390DN/W, SNC-521IR/W, SNC-565IR/W, SNC-620/W, SNC-670ID/W
Sanyo:
VCC-HD3500, VDC-HD3500, VDC-HD3500p, VCC-HD2100, VCC-HD2100P
VCC-HD2300, VCC-HD2300P, VDC-HD3100, VDC-HD3100P
VCC-HD3300, VDC-HD3300, VDC-HD3300P, VCC-HD4600, VCC-HD4600P
VCC-HD5400, VCC-HD5400P, VCC-HD5600, VCC-HD5600P
StarDot:
SD-130, SD-300, SD-500, SDEXP4, SDEXP2
VIVOTEK:
IP8161, VS8102, FD8161, FD8361
Notice:
1. Only compatible with NUUO MainConsole v3.3.0 above
2. Must install Main Console software before install device pack v1.1.0
37 / 38
37
NVR Device Pack Release Note
NUUO version 2.6.0
38 / 38
38
Download PDF