DBL Technology | VoIP FXS+PSTN Gateway | User manual | DBL Technology VoIP FXS+PSTN Gateway User manual

User Manual
VoIP FXS+PSTN Gateway
Model: HT-822P
For DC24V Only
Shenzhen HyberTone Technology Co.,Ltd.
Http://www.hybertone.com
Support@hybertone.com
Marketing@hybertone.com
Date: 2007-9-17
Version: A38HS-3.11-6
HT-822P VoIP FXS+PSTN Gateway
Http://www.hybertone.com
Contents
1 Product Introduction.......................................................................4
1.1 General Information............................................................................................................4
1.2 Protocol...............................................................................................................................4
1.3 Hardware Specification.......................................................................................................5
1.4 Software Specification ........................................................................................................5
1.5 List of the Package..............................................................................................................5
1.6 View of the Appearance ......................................................................................................6
2 Installation.........................................................................................6
2.1 Installation Steps .................................................................................................................6
2.2 Connection Diagram ...........................................................................................................7
3 Basic Operations .............................................................................7
3.1 Star Command ....................................................................................................................7
3.1.1 Star Commands for Phone Configuration.........................................................7
3.1.2 Star Commands for Phone Operation ...............................................................8
3.2 Set up ..................................................................................................................................8
3.3 Make Phone Calls ...............................................................................................................9
3.3.1 Using Star (*) Commands for Phone Operations ............................................9
3.3.1.1 Call-waiting/flash..........................................................................................9
3.3.1.2 Call Hold.......................................................................................................9
3.3.1.3 Call-transfer ................................................................................................10
3.3.1.4 Call-forward................................................................................................10
3.3.2 Placing a Call ......................................................................................................10
3.3.3 Send and Receive PSTN Calls ........................................................................10
3.3.4 Send and Receive VoIP Calls........................................................................... 11
3.3.5 Send by Phone Book ......................................................................................... 11
3.4 LED Light Pattern Indication............................................................................................ 11
4 Configuration Guide...................................................................... 13
4.1 Access the Web Configuration Menu................................................................................13
4.2 Status.................................................................................................................................15
4.2.1 Phone Information..............................................................................................15
4.2.2 Network Information...........................................................................................15
4.3 Configurations Options.....................................................................................................16
4.3.1 Language.............................................................................................................16
4.3.2 Time Zone and Time Server .............................................................................17
4.3.3 Auto-provision .....................................................................................................17
4.3.4 Remote Control...................................................................................................17
4.3.5 Pound(#)Key and Auto-dial Timeout................................................................18
4.3.6 Network Tone ......................................................................................................18
1
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
4.3.7 Default Connect ..................................................................................................20
4.4 Call Settings ......................................................................................................................20
4.4.1 H.323 Phone .......................................................................................................21
4.4.1.1 Single Configuration ...................................................................................21
4.4.1.2 Configuration by Line .................................................................................22
4.4.1.3 Configuration by Group ..............................................................................22
4.4.1.4 Advance Settings.........................................................................................23
4.4.1.5 H.323 Direct Mode .....................................................................................25
4.4.2 SIP Phone ...........................................................................................................25
4.4.2.1 Single Configuration ...................................................................................26
4.4.2.2 Configuration by Line .................................................................................28
4.4.2.3 SIP Advance Settings ..................................................................................28
4.4.3 Media Setting ......................................................................................................30
4.4.4 Codec Preference ..............................................................................................31
4.4.5 NAT Traversal .....................................................................................................32
4.4.5.1 Signaling NAT Traversal.............................................................................32
4.4.5.2 Media NAT Traversal..................................................................................33
4.4.6 Billing Support.....................................................................................................34
4.4.7 Dial Plan ..............................................................................................................34
4.4.7.1 Basic Dial Rule ...........................................................................................35
4.4.7.2 How to limit code bit ..................................................................................35
4. 5 User Command ................................................................................................................36
4.5.1 Start VoIP dial......................................................................................................37
4.5.2 Switch to PSTN...................................................................................................37
4.5.3 Hold Key ..............................................................................................................37
4.5.4 Transfer Key........................................................................................................37
4.5.5 Star Command Input Timeout...........................................................................37
4.6 Gain Setting… ..................................................................................................................37
4.7 PhoneBook........................................................................................................................38
4.8 About FAX ........................................................................................................................39
4.9 Network Configurations....................................................................................................39
4.8.1 LAN Port configurations ....................................................................................40
4.8.2 PC port configurations .......................................................................................41
4.8.3 Primary DNS .......................................................................................................43
4.8.4 Secondary DNS..................................................................................................43
4.9 Save Configuration ...........................................................................................................43
4.10 Discard Changes .............................................................................................................44
4.11 Tools Menu .....................................................................................................................44
4.11.1 Online Upgrade.................................................................................................44
4.11.2 Change Password ............................................................................................45
4.11.3 Reset Configuration .........................................................................................45
4.11.4 Reboot the Device............................................................................................46
5 Products Parameter ...................................................................... 46
2
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
6 Manufactory Parameter ................................................................ 47
3
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
1 Product Introduction
1.1 General Information
An Analogue Telephone Adaptor (ATA) is an analogue-to-digital adaptor that allows you to
use your standard telephone or telephone system. ATA is designed to realize voice
communication over a broadband IP network. It offers high voice quality with minimal
bandwidth requirement. No matter it could access to the public IP address or not, the
device has the advantage of easy installation in simple or complex network Multiple IP
phones can also be installed in the same network with only one public IP address. It
comes with enriched features for both network and phone applications, such as
broadband router, DHCP, LAN Phone System.
The HT-822P IP ADAPTOR is an all-in-one VoIP integrated device, which is designed to
be a total solution for network’s providing VoIP services. Its functions are available via a
regular analog telephone. The HT-822P IP ADAPTOR has two VoIP lines and one PSTN
port.
1.2 Protocol
TCP/IP V4 (IP V6 auto adapt)
ITU-T H.323 V4 Standard
H.2250 V4 Standard
H.245 V7 Standard
H.235 Standard(MD5,HMAC-SHA1)
ITU-T G.711 Alaw/ULaw, G.729A, G.729AB, and G.723.1 Voice Codec
RFC1889 Real Time Data Transmission
Proprietary Firewall-Pass-Through Technology
SIP V2.0 Standard
Simple Traversal of UDP over NAT (STUN)
Web-base Management
PPP over Ethernet (PPPoE)
PPP Authentication Protocol (PAP)
Internet Control Message Protocol (ICMP)
TFTP Client
Hyper Text Transfer Protocol (HTTP)
Dynamic Host Configuration Protocol (DHCP)
Domain Name System (DNS)
User account authentication using MD5
Out-band DTMF Relay: RFC 2833 and SIP Info
4
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
1.3 Hardware Specification
ARM9E Processor for high performance
DSP for voice codec and voice processing
Two 100M Based Ethernet ports in comply with IEEE 802.3 for both LAN and PC
connection.
LEDs for Ethernet port status
Two FXS ports
One PSTN port
Ethernet Bridge
1.4 Software Specification
LINUX OS
Built-in HTTP for accessing internal parameters
PPPoE dial-up
NAT Broadband Router functions
DHCP Client
DHCP Server
Firmware On-line upgrade
Phone Book
Memory Dial
Caller ID
Multiple Language Support
With Accounting Function
1.5 List of the Package
a)
b)
One HT-822P IP ADAPTOR
One universal power adaptor DC24V/500mA
Warning: The two different power adaptor is use in different kind’s HT-822P. Please
don’t mix up it.
c)
One Ethernet cable (3m)
5
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
1.6 View of the Appearance
1) Phone 1
It is connected with a standard touch-tone analog telephone.
2) Phone 2
It is connected with another standard touch-tone telephone.
3) LINE IN
It is connected with a standard telephone cable PSTN or VoIP.
4) LAN
It is used to connect the Ethernet cable.
5) PC
It is used to connect a computer or other terminal.
6) POWER DC24V/500mA
It is the power port, connected with the power adaptor.
Warning: The two type power adaptor are use by different kind’s HT-822P, Please
don’t mix up it.
7) Reset
It’s used to reboot the terminal.
2 Installation
2.1 Installation Steps
The HT-822P IP ADAPTOR has two PHONE ports(Phone1,Phone 2), one LINE IN port,
one NETWORK port and one PC port. The PHONE ports can register to the same SIP or
H.323 account or two different SIP or H.323 accounts.
Please follow the following steps to install an HT-822P IP ADAPTOR:
6
Http://www.hybertone.com
a)
b)
c)
d)
e)
HT-822P VoIP FXS+PSTN Gateway
Connect a standard touch-tone analog telephone to the PHONE port.
Insert a standard RJ11 telephone cable into the LINE IN port and connect the other
end of the telephone cable to a wall jack.
Insert the Ethernet cable into the LAN port of HT-822P IP ADAPTOR and connect the
other end of the Ethernet cable to an uplink port (a router or a modem, etc.)
Connect a PC to the PC port of HT-822P IP ADAPTOR.
Insert the power adapter into the HT-822P IP ADAPTOR and connect it to a wall
outlet.
2.2 Connection Diagram
The interconnection diagram is as follows:
3 Basic Operations
3.1 Star Command
There are two types of Star Commands. One is factory predefined star command for
phone setup and information purpose. The other is for phone operation. The first digit of a
command must be “*” and the rest must be the natural number from 0 to 9. There are also
some commands with operands.
3.1.1 Star Commands for Phone Configuration
The star commands for phone configuration generally contains three digits or more. This
7
HT-822P VoIP FXS+PSTN Gateway
Http://www.hybertone.com
kind of star command is shown in the table below.
Star(*) Command
Function
*01
Read LAN Port IP
*02
Read PC Port IP
*03
Set LAN Port IP. Pick up the handset, press
*03, and then follow the instruction of the
phone to set the IP address.
*04
Set PC Port IP. Pick up the handset, press
*04, and then follow the instruction of the
phone to set the IP address.
*20
Send a remote support request.
*09987456
Reset IP:
LAN Port IP:
192.168.0.1 (The new terminal are DHCP
default)
PC Port IP:
192.168.8.1(The new terminal are Fixed
Mode.)
*11983185922
Reset system configuration. Return to the
default configuration.
Note: These commands are factory preset and cannot be modified.
3.1.2 Star Commands for Phone Operation
The star commands for phone operation are 3-digit long at least and some contains
operands. These star commands are shown in the table below.
Star(*) Command
Function
*12
Switch to VOIP line
*21
Switch to PSTN line
*42
Hold the current call / Release the Hold call
*41
Call Transfer to another VoIP Number
*50
Phone book function key
3.2 Set up
The setup of the HT-822P IP ADAPTOR can be done via auto-provisioning if the service
provider supports this feature. Local setup is supported via built-in web pages. To access
the web pages, the LAN or PC port IP address is required. The HT-822P IP ADAPTOR is
equipped with voice prompts to read LAN port and PC port IP addresses via the Phone 1
8
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
or Phone 2 port.
Please refer to the table in section 3.1.1 for detailed information. While seting up, please
follow the instructions as follows :
a)
b)
c)
d)
e)
When the HT-822P IP ADAPTOR fails to set the LAN Port and PC Port IP addresses,
it reports 0 on *01 or *02 Star Commands.
When the PC port is configured into Bridge Mode, it also report zero.
*03 and *04 can be dialed to set the LAN Port IP address and PC Port IP address. For
example, if you want to set the PC Port’s IP address to 192.168.5.10, please press
the following keys orderly : “*04192.168.5.10#”. Note : enter Symbol “*” replace “.”
and end with “#”.
A special star (*) command (*09987456) can be dialed to reset both LAN port and PC
port to the factory default IP. By the new firmware, the default setting was the LAN
port is DHCP mode, the PC port is bridge mode.
The star command *11983185922 can be dialed to reset the system configuration or
return to the default configuration.
3.3 Make Phone Calls
3.3.1 Using Star (*) Commands for Phone Operations
Refer to the table in section 3.1.2 for detailed values of the star commands for phone
operation.
3.3.1.1 Call-waiting/flash
When you are talking on the phone and another call comes in on your phone extension, a
short tone sounds in your handset. You can give the waiting indications such as accepting
the call, or neglecting the call.
Note: This function only support by SIP protocol.
3.3.1.2 Call Hold
Call Hold lets you put a caller on hold for a certain period of time. There are two kinds of
call hold:
a) When you are in the conversation with a party, you can press “*42” on the phone
keypad to place the first party on hold. You will hear a dial tone. Enter a new phone
number to make another call. After finishing the second call, you can press the “*42”
again to return to the former call on hold.
b) When you are talking on the phone and another call comes in on your phone
9
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
extension. To temporarily put the present caller on hold and answer the new incoming
call, press *42 and you will hold the current call. And press *42 again, you will return
to the former call.
Note: This function only support by SIP protocol.
3.3.1.3 Call-transfer
If A and B are in the process of a call, A can transfer A-B call to B-C call. There are two
kinds of transfer, which are attended transfer and unattended transfer.
a) Attended Transfer
When a call is in progress and you agree with him/her to have a call transfer, press
“*41”, and when you hear dial tone, dial another phone number to announce a
transfer. If the third party agrees, you hang up your phone.
b) Unattended Transfer
When a call is in progress and you agree with him/her to have a call transfer, press
“*41”, and when you hear dial tone, dial another phone number. When you hear ring
tone, just hung up your phone without a conversation with the third party.
Note: This function only support by SIP protocol.
3.3.1.4 Call-forward
Call- forward is an arrangement whereby a call coming into an unanswered or busy line
will be FORWARDED to a predestinated line. Contact the Telephone Services office for
implementation of this feature.
Please refer to the “Call Settings” in section 4.2.3.3 for the configuration instructions.
Note: This function only support by SIP protocol.
3.3.2 Placing a Call
a) Dial the number and wait for 5 seconds. Or
b) Dial the number and press “#”
3.3.3 Send and Receive PSTN Calls
Users can send and receive calls from the PSTN.
A. To receive PSTN calls, just take the phone off hook when it rings.
B. To make a PSTN call:
a)
If the default connect of FXS MODE in the configuration web is VoIP, press *21 (or
10
HT-822P VoIP FXS+PSTN Gateway
Http://www.hybertone.com
b)
your own PSTN Access Code) at first. Wait for the PSTN dial tone and dial the PSTN
number.
If the default connect of FXS MODE in the configuration web is PSTN, dial the phone
number directly.
3.3.4 Send and Receive VoIP Calls
Users can send and receive calls from the VoIP.
A. To receive VoIP calls, just take the phone off hook when it rings.
B. To make a VoIP call:
a) If the default connects is VoIP, dial the number directly.
b) If the default connect is PSTN, press *12 at first and then dial number.
3.3.5 Send by Phone Book
Users can send a phone number in phone book.
Dial *50 and the phone book’s location number.
For example: you want call ‘tony’, then dial ‘*5003’,the terminal will auto dial number
‘008723245897’
3.4 LED Light Pattern Indication
The following table shows the LED light pattern indication.
LED
DESCRIPTION
RUN
1. When the device is booting up, the LED
will flash 100ms ON and 100ms OFF.
2. When the device is connected with the
server, the LED will flash 1s ON and 1s
OFF.
3. If the ATA does not boot up, the LED
will not flash.
LAN
1.
When the LAN receptacle is connecting
with the network, the LAN LED will light
11
HT-822P VoIP FXS+PSTN Gateway
Http://www.hybertone.com
2.
PC
1.
2.
L1
1.
2.
L2
1.
2.
up continuously. ( The LED will not light
up if the network connection is
unavailable )
If there is data transmitting through the
ATA, the LAN LED will blink. (Example:
During a VoIP call, the LED will keep
blinking.)
When the PC receptacle is connecting
with the network, the PC LED will light
up continuously. (The LED will not light
up if the network connection is
unavailable.)
If there is any data transmitting through
this receptacle, the PC LED will keep
blinking.
L1 LED will be off when the phone is on
hook.
L1 LED will be on when the phone is off
hook.
L2 LED will be off when the phone is on
hook.
L2 LED will be on when the phone is off
hook.
12
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
4 Configuration Guide
Before configuring the HT-822P IP ADAPTOR, first you should obtain the LAN or PC IP
address through voice prompt. Follow section 3.1 for detailed information to get the LAN
or PC IP Address.
HT-822P IP ADAPTOR has an embedded Web server that will respond to HTTP
GET/POST requests. It also has embedded HTML pages that allow users to configure the
HT-822P IP ADAPTOR through a Web browser.
4.1 Access the Web Configuration Menu
The HT-822P IP ADAPTOR HTML configuration menu can be accessed via LAN or PC
port:
With the LAN access is enabled, get the LAN IP address of the HT-822P IP ADAPTOR as
described in section 3.1.1. The HT-822P IP Adaptor’s Web Configuration page can then
be accessed by entering the URI into a web browser.
For example Use the LAN port IP address login the HT-822P WEB page. Hypothesis the
LAN port IP is 192.168.2.216, then run IE and input 192.168.2.216 or
http://192.168.2.216to IE’s address field:
http://192.168.2.216
Once this HTTP request is entered and sent from a Web browser, the HT-822P IP
ADAPTOR will respond with the following login screen:
13
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
To login the Administration Configuration page, please enter “admin” in the User Name
field and “admin” (default) in the Password field and then click on the OK button. The PC
Browser then shows the window below and you have successfully entered the HT-822P IP
ADAPTOR HTTP WEB Interface.
Administration configuration includes not only the end user configuration, but also
advanced configuration such as SIP configuration, and other miscellaneous
configurations. The default page is for Status settings as shown on the right hand side of
the window. To change to a different menu choice, just click on one of the choices on the
left hand menu column. The advanced configuration page is shown in the following
sections.
14
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
4.2 Status
As shown in the figure above, there are four main fields to be configured on the Status
page.
4.2.1 Phone Information
A. Serial Number
Each ATA has a unique serial number assigned by the factory such as
HT822POLDTEST09. This number is important for centralized configuration, technical
support, and warranty repair. This number is printed in the back of the ATA and is
associated with your software license. This field is read-only.
B. Firmware Version
Firmware version refers to the software version of the ATA such as A38HS-3.11-1,
which is used to identify the software version.
C. Hardware Revision
These fields show terminal’s hardware type.
D. Phone Status
This field shows the status of Line’s connection status. If the connection is successful,
this field displays LOGIN. Otherwise show LOGOUT.
4.2.2 Network Information
A.
LAN Port Configuration
This field shows the current IP address used by LAN port such as 192.168.100.119.
The ATA LAN port can be configured to obtain its IP address by DHCP or the IP
address can be set statically, used mainly while using the ATA with a DSL line.
B. PC Port Configuration
This field shows the current IP address used by PC port. In the Bridge Mode, the ATA
allows a PC connected to it to pass through to the network. No other PC Configuration
settings are set; the Advanced, Gateway, Primary and Secondary DNS field settings
are not required and can be ignored.
C. PPPoE
This field shows the status of your broad band connection with Dial-up networking in
the ATA has not been enabled. The ATA is designed to be used over the Internet with a
broadband connection.
D. Default Route
Default Route is the IP address of a router that is used when a device sends a packet
to another subnet or when a device sends a packet to an unknown destination.
E. DNS Server
Each zone is served by at least one Domain Name Server, which contains the
complete data for the zone. (To make the DNS tolerant of server and network failures,
15
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
most zones have two or more authoritative servers.) A name server retains the
address and routing information for IP users.
4.3 Configurations Options
Click on the “Configurations”, the web page will pop-up a subordinate options. Click on
“Preference” in the left menu of the configuration web, and the screen will be displayed as
follows:
4.3.1 Language
Select web provisioning language as English or Chinese. For example, if your present
language used is English, please click “English” in the “Language” menu, When the
terminal was reboot the web page will display all information in English.
You can choice the language use the quick link, the Web page’s language will change at
soon.
16
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
4.3.2 Time Zone and Time Server
This parameter controls how the date/time displayed, it will be adjusted according to the
specified time zone. The ATA uses Network Time Protocol (NTP) to retrieve date and time
information from an NTP server (Time Server). The time is in GMT ± offset. For example,
Pacific Standard Time is GMT-8, and Pacific Daylight Time is GMT-7.
Time Server is the Network Time Protocol server where the IP Phone retrieves date and
time information. This field shows the NTP server IP address such as timekeeper.isi.edu.
4.3.3 Auto-provision
Allow central provisioning of HT-822P. Auto-provision is the automatic configuration of
devices without manual intervention and without any need for software configuration
programs or jumpers. Ideally, auto-provision devices should just "Plug and Play".
Auto-provision has been made common because of the low cost of microprocessors and
other embedded controller devices. It includes Auto-provision Server and Auto-update.
This is the special service only. It must support by HyberTone’s Auto-provision Server.
4.3.4 Remote Control
This function is for remote login the HT-822P’s WEB page traverse the NAT, you not need
to make a DMZ or other Port mapping when you want login to a remote device.
This is the special service only. It must support by HyberTone’s Remote Control Server. It
was free software. If you want use this function, Please connect us.
17
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
The Remote Control star command is *20, this star command’s rule is:
*20 + Server IP + Server Port + #
For examples, if you want send a support request to the engineer and your SIP’s Remote Control
Server’s IP is 222.111.222.111, the Remote Server Port is 1920. You can dial the command like
this: *20222*111*222*111*1920#.
If you set this IP and Port on you device’s Web, you only dial *20#.
4.3.5 Pound(#)Key and Auto-dial Timeout
If you want the terminal send out your telephone number shortly, please click the Pound(#)Key
enable. If it was disable, the terminal will wait period of time after a telephone number is
entered
Set the wait time before auto dialing after a telephone number is entered. Auto dial time is
the period of time from dialing the end number to sending out your dial information, before
the called phone rings.
The range is: 3 to 15 second, the default setting is 5 second.
4.3.6 Network Tone
The Network Tone is the dial tone one hears when he or she picks up the handset to make
a call, and the ring back tone when he or she dial to a number. You can select the network
tones from the following tones as shown in the following screen, depending on the country
where the ATA is located.
18
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
You can configure the Network Tones as Customized option:
The parameters are fill-in as true digits as below format:
nc, rpt, c1on, c1off, c2on, c2off, c3on, c3off, f1, f2, f3, f4, p1, p2, p3, p4
Chapter Descriptor:
nc: number of cadences
rpt: repeat counter(0 - infinite, 1~n - repeat 1~n times)
c1on: cadence one on (in milliseconds)
c1off: cadence one off (in milliseconds)
c2on: cadence two on (in milliseconds)
c2off: cadence two off (in milliseconds)
c3on: cadence three on (in milliseconds)
c3off: cadence three off (in milliseconds)
f1: tone #1, 300-3000(Hz)
f2: tone #2, 300-3000(Hz)
f3: tone #3, 300-3000(Hz)
f4: tone 34, 300-3000(Hz)
p1: attenuation index #1, 0~31(0=3dB, -1dB increments)
p2: attenuation index #2, 0~31(0=3dB, -1dB increments)
p3: attenuation index #3, 0~31(0=3dB, -1dB increments)
p4: attenuation index #4, 0~31(0=3dB, -1dB increments)
For example, you want add a tone as 450Hz and it is run 700 milliseconds and off 1000
milliseconds. You only add below parameters in corresponding option:
1,0,700,1000,0,0,0,0,450,0,0,0,20,0,0,0
19
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
4.3.7 Default Connect
There are two kinds of default connect: VoIP and PSTN. You can switch between the two
connects.
a) Short for Voice over IP, VoIP is a category of hardware and software that enables
people to use the Internet as the transmission medium for telephone calls by sending
voice data in packets using IP. Select this field to set your default connects into VoIP. If
you make a VoIP call, please dial the called number directly. If you make a PSTN call,
press *21 first and then dial the called number.
b) PSTN stands for Public Switched Telephone Network, referring to the international
telephone system based on copper wires carrying analog voice data. Select this field
to set your default connects into PSTN. If you make a VoIP call, please press *12 first
and then press the called number. If you make a PSTN call, please dial the number
directly.
The user can change the switch command. But it must using “*” by front.
Note: By way of differentiate the connect kinds (VoIP or PSTN). HT-822P using a
different network tone. The VoIP estate network tones have a transitory
intermission. The PSTN estate network tone is consecutive.
4.4 Call Settings
This chapter is about the basic settings to set up the internet connection through the ATA,
concerning two endpoint types: H.323 and SIP. The configuration screen is shown as
follows.
20
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
4.4.1 H.323 Phone
H.323 is the international standard for multimedia communication over packet-switched
networks, including LANs, and the Internet. There are three kinds of FXS mode to
configure: 1) Single Configuration; 2) Configuration by line ; 3)Configuration by Group .
4.4.1.1 Single Configuration
In this configuration mode, you can give the two phones connected to the ATA the same
configurations in the following items.
A. H.323 Phone Number
H.323 phone number is a sequence of decimal digits that is used for identifying a
telephone line in a telephone network. For example, 5551234 is a valid phone number. On
the Call Settings screen, enter the phone number in the Phone Number field.
B. Display Name
This field shows the H.323 client display name. It is what the call party sees on his phone
LCD when you call them such as John Smith.
C. H.323 ID
H.323 ID is an alphanumeric string representing names, e-mail address, etc.. It may be a
user name, conference name, e-mail name, or other identifier.
D. Gatekeeper Address
Gatekeeper address is used for finding the correct gatekeeper. It maybe an IP address
such as 192.168.2.197 or a domain name like gk.yourisp.com. On the Call Settings
screen, enter the gatekeeper address in the Gatekeeper Address field. If your gatekeeper
used nonstandard signaling port(The default port is 1719), you can configure it with
gatekeeper address field such as 192.168.2.197:2000 or gk.your.com:2000 (the 2000 is
your gatekeeper’s signaling port).
21
Http://www.hybertone.com
F.
HT-822P VoIP FXS+PSTN Gateway
Enable Auth
If you click the “Enable Authentication” field, you will have to configure the Auth ID and
Password. A pair of authentication ID and password is usually needed to use the ATA.
4.4.1.2 Configuration by Line
In this mode, you will have more advance control over the two FXS ports. Firstly, phone 1
and phone 2 will refer to different service providers for related service. Secondly, you can
bind the phone numbers or the FXS ports with each phone. That is to say, one phone
terminal can be bound with one phone numbers. You will have to set the bellow items into
different values. The configuration page is shown as below. The option setting please
follows section “Single Configuration” for detailed information.
4.4.1.3 Configuration by Group
In this mode, each FXS port can be bound with two H.323 service providers; That is to say,
one phone terminal can be bound with two phone numbers. The configuration page is
shown as below. The option setting please follows section “Single Config” for detailed
information.
22
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
4.4.1.4 Advance Settings
Click on “Advance Settings” in the H.323 menu, the configuration screen of advance
settings will be displayed as follows. In this part, you will have more advance control over
the H.323 signaling.
A) RAS Port
RAS Port is connected to an unreliable channel, which is used to convey the registration,
admissions, bandwidth change, and status messages between two H.323 entities.
B) Q.931 Port ( Call Signaling Port )
23
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
Call Signaling Port is connected to a reliable channel used to convey the call setup and
teardown messages between two H.323 endpoints.
C) H.245 Port ( Media Control Ports )
Media control port is the port or port range used by the H.245 media control protocol. Note:
the H.245 media control protocol uses TCP.
D) Fast Start
Enable or disable the Fast Start procedure described in H.225.0. This option is mainly
used for testing and solving compatibility problems. If not sure, let this option unselected.
E) Register Mode
A: Register Multiple Numbers
In this register mode, devices will send all account’s register request in one
signaling when then use same one GK.
B: Register Multiple Times
In this register mode, devices will send the register request one by one.
F) DTMF Signaling
1) DTMF TYPE
DTMF TYPE is used for telephone signaling over the line in the voice frequency band
to the call switching center. DTMF means that two groups of tone with different
frequencies are united into 16 kinds of dial tone. The telecommunication station,
switch or the phone service such as 1860 identify these special tones through DSP
analysis to confirm the keys dialed by user. There are two DTMF types: Inband DTMF
type and Outband DTMF type.
Inband DTMF type transfers these special dial tones together with the speech tone
without doing any special processing to them. So there is not any type as to Inband
DTMF.
Outband DTMF type transfers these special dial tones by some special method to
confirm its correctness. The special method is the so called protocol such as
RFC2833 and SIP information.
2)DTMF Payload Type
24
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
DTMF Payload Type is used to carry telephony tones and telephony signals. By using
a distinct dynamic RTP payload type in the same RTP stream as the media, it is
possible to carry DTMF tones, fax-related tones, standard subscriber line tones,
country-specific tones and trunk events.
G) Signaling Qos
4.4.1.5 H.323 Direct Mode
This is the Point to Point mode.
4.4.2 SIP Phone
SIP (Session Initiation Protocol) is a relatively new Internet standard. It is a simple,
low-level protocol for initiating interactive communication sessions between users. These
sessions can involve two or more users. Such sessions include voice, video, chat,
interactive games, and virtual reality.
There are two configuration modes: 1) Single Configuration; 2) Configuration by Line
25
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
4.4.2.1 Single Configuration
In this FXS mode, you can give the two phones connected to the ATA the same
configurations in the following items.
A)Phone Number
This field use fill in the SIP client authentication ID. It is the telephone number (or
extension) you assigned to the VoIP SIP Phone such as 123456. enter the phone number
in the Phone Number field.
B)SIP Proxy
The SIP proxy server acts as the call manager of all the incoming or outgoing calls to and
from the SIP Phone. The proxy address is the IP address or domain name of your IP-PBX
or VoIP service switch. For example, gk.yourisp.com or 192.168.2.197 may be a proxy
address.
If your SIP proxy used nonstandard signaling port (the default port is 5060), you can
config it with SIP proxy address field such as 192.168.2.197:2000 or gk.your.com:2000
(the 2000 is your SIP proxy signaling port).
C)SIP Registrar Server
A registrar is a SIP server responsible for keeping track of where a user is contactable,
and providing information to callers. This field shows the SIP registrar server IP address.
If your SIP registrar server used nonstandard signaling port (the default port is 5060), you
26
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
can config it with SIP registrar server address field such as 192.168.2.197:2000 or
gk.your.com:2000 (the 2000 is your SIP registrar server signaling port).
D)Home Domain
This field use fill in the IP address of the home domain. Although the IP address is easy to
remember, the user still finds it hard to remember because it is long and has no
association with its geographical position or organizational relationship. In order to solve
the problem, Internet defines the Domain Name System (DNS) by using ASCII string.
E)Authentication ID
This field use fill in the SIP client authentication ID. Authentication mainly is the
identification of the user. The IP messages between two parties use an authentication
mechanism based on IDs and passwords. The authentication IDs and passwords are the
credentials to determine whether the IP Proxy should accept or reject a session invitation.
F) Password
This field use fill in the SIP client authentication password.
G) Call Forward
1) Forward Type
Select the forward method as follows: Not Forward, Unconditional Forward, Forward
on Busy.
1) Not Forward means you will not forward the incoming calls.
2) If you select Unconditional Forward, you will set the phone into forwarding any call
without any conditions.
3) When you are in the process of a call, a third call comes in. If you select Forward on
Busy in the configuration, the third call will be forwarded automatically. However, if
your phone is idle when a call comes in, the call will not be forwarded.
2) Forward Number
This field shows the SIP client forward number. Take an example to explain it. If user
A transfers A-B call to B-C call, the number of user C is the forward number.
H) Display Name
This field shows the SIP client display name. It is what the call party sees on his phone
LCD when you call them such as John Smith.
I) Backup Server
27
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
This is the spare VoIP system information, it offer a choice when the current system has
some problem.
4.4.2.2 Configuration by Line
In this mode, you will have more advance control over the two FXS ports. Firstly, phone 1
and phone 2 will refer to different service providers for related service. Secondly, you can
bind the phone numbers or the FXS ports with each phone. That is to say, one phone
terminal can be bound with two phone numbers. You will have to set the above items into
different values. The configuration page is shown as below.
4.4.2.3 SIP Advance Settings
Click on “Advance Settings” in the SIP menu, the configuration screen of advance settings
will be displayed as follows. In this part, you will have more advance control over the SIP
signaling.
28
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
A) Signaling Port (SIP Local port)
SIP local port is the local UDP port; the SIP proxy could have a conversation with SIP
proxy server or other SIP user.
B) Outbound Proxy
This field shows the SIP outbound proxy IP address. In most cases, the SIP outbound
proxy is placed alongside the firewall and is the way to let SIP traffic pass from the internal
network to the Internet. Please ask your network administrator for these parameters.
C) NAT Keep-alive
Send NAT Keep_alive message to SIP server.
D) P2P
Point to point mode.
E) Virtual Ringback
F) Advanced Timing
29
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
F) DTMF Signaling
1) DTMF TYPE
DTMF TYPE is used for telephone signaling over the line in the voice frequency band
to the call switching center. DTMF means that two groups of tone with different
frequencies are united into 16 kinds of dial tone. The telecommunication station,
switch or the phone service such as 1860 identify these special tones through DSP
analysis to confirm the keys dialed by user. There are two DTMF types: inband DTMF
type and outband DTMF type.
Inband DTMF type transfers these special dial tones together with the speech tone
without doing any special processing to them. So there is not any type as to inband
DTMF.
Outband DTMF type transfers these special dial tones by some special method to
confirm its correctness. The special method is the so called protocol such as
RFC2833 and SIP information.
2)DTMF Payload Type
DTMF Payload Type is used to carry telephony tones and telephony signals. By using
a distinct dynamic RTP payload type in the same RTP stream as the media, it is
possible to carry DTMF tones, fax-related tones, standard subscriber line tones,
country-specific tones and trunk events.
G) Signaling Qos
H) SIP Local Port
SIP Local Port is the local UDP port used by the SIP client to communicate with SIP proxy
and other SIP user agents.
I) Enable Call Wait
Select “Enable Call Wait”, you will enable your phone connected to the ATA to have the
function of call waiting.
4.4.3 Media Setting
Click on “Media Settings” in the “Call Setting” menu, the configuration screen of advance
settings will be displayed as follows. In this part, you will have more advance control over
the media.
30
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
A) RTP Ports
RTP (Real Time Protocol) Port is the target transport address for the RTP audio stream to
be sent to.
B) Packet Length
it means the time of single network packet sent out . The default time is 20ms.
C) Jitter Buffer
D) Media Qos
RTP TOS is a service field in UDP IP packets carrying a RTP data. Enter RTP TOS if your
network supports DiffServ and can prioritize the packets to maintain voice quality.
4.4.4 Codec Preference
The Codec Preference is inside the media setting menu. Click on “Codec Preference” in
31
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
the “Call Settings à Media Setting” configuration page, the “Codec Preference” screen
will be displayed as below.
Codec preference is the order of voice codec. The default one is up transmitting, which is
the set mode for common users.
4.4.5 NAT Traversal
4.4.5.1 Signaling NAT Traversal
Click on the “Signaling NAT Traversal” in the “Call Settings” configuration page’s “Advance
Settings”, the “NAT Traversal” screen will be displayed as follows.
Signaling NAT Traversal can make and receive calls through any type of NAT device.
There are three kinds of NAT traversal:
A) None
None means there is no traversal mechanism supported.
B) Port-forwarding Support
Port-forwarding is the action of forwarding network ports on the LAN interface to PCs or
servers in LAN network. Virtual servers use this technique to allow external users, in most
cases via internet, to reach services provided by internal servers such as FTP, HTTP,
Telnet, etc.
Port-forwarding support includes gateway address and echo server address. Gateway is a
communication device that connects two different networks. Echo server is a standard
service implementing the ECHO protocol.
C) STUN (RFC 3489 )
STUN stands for Simple Traversal of UDP over NAT. It is a protocol which enables the SIP
32
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
phone to detect the presence and type of NAT behind which the phone is placed. SIP Stun
Server refers the SIP address of the Stun Server.
D) Nat Citron
It only use by H.323 protocol.
E) Relay Proxy
Relay proxy is HyberTone's proprietary NAT traversal technology which enables
HyberTone's VoIP terminals to achieve successful deployment in most LAN environments.
It includes address, ports, user name, and password.
Note: This RELAY proxy is only compatible with the RELAY Server software developed by
HyberTone independently. It was free software; you can come down on us.
4.4.5.2 Media NAT Traversal
Click on the “Media NAT Traversal” in the “Call Settings” configuration page’s “Media
Settings”, the “NAT Traversal” screen will be displayed as follows.
Media NAT Traversal can make and receive calls through any type of NAT device. There
are four kinds of NAT traversal:
A) None
None means there is no traversal mechanism supported.
B) Port-forwarding Support
Port-forwarding is the action of forwarding network ports on the LAN interface to PCs or
servers in LAN network. Virtual servers use this technique to allow external users, in most
cases via internet, to reach services provided by internal servers such as FTP, HTTP,
Telnet, etc.
Port-forwarding support includes gateway address and echo server address. Gateway is a
communication device that connects two different networks. Echo server is a standard
service implementing the ECHO protocol.
C) STUN (RFC 3489 )
STUN stands for Simple Traversal of UDP over NAT. It is a protocol which enables the SIP
phones to detect the presence and type of NAT behind which the phone is placed. SIP
Stun Server refers the SIP address of the Stun Server.
D) Relay Proxy
Relay proxy is HyberTone's proprietary NAT traversal technology which enables
HyberTone's VoIP terminals to achieve successful deployment in most LAN environments.
It includes address, ports, user name, and password.
33
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
The RELAY can run in three modes:
Mode 1: The media use UDP packets and encrypt;
Mode 2: The media use UDP packets and encrypt; The UDP packets use single
UDP port;
Mode 3: The media use TCP packets and encrypt; The TCP packets can choice
single TCP port;
The mode 2 and mode 3 is the passiveness, the port was designation from RELAY
SERVER.
Note: This RELAY Proxy is only compatible with the RELAY Server software developed by
HyberTone independently. It was free software; you can come down on us.
4.4.6 Billing Support
HT-822P can support two kinds billing mode. First is using HyberTone’s billing software,
otherwise is using the Reverse Signal.
If you using the HyberTone’s billing software, click the “Billing Support” by the “Call
Setting” and select the Billing software’s version by the “Billing Version”.
The HyberTone’s billing software version2.0 was support fixed billing computer. If you
using the version2.0, you can appoint the billing computer’s IP, enter the IP into Billing
Server field.
The terminal can support billing by normal Reverse Signal. It was without config.
About the HyberTone’s billing software can download by http://www.hybertone.com, it was
free.
4.4.7 Dial Plan
HT-822P apply to the rule dialing out the telephone number ,user can set the rule in the
panel of Call Settings.
34
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
4.4.7.1 Basic Dial Rule
1. If there are many rules, it can be separated with symbol '|'. For example:
"00:-00|0:-0+86|:+86755"
2. System try to match the rule from left to right and stop match when meet the satisfied
rule, otherwise continue.
3. Rule grammar model is "AA:-aa+bb", For example: "0:-0+86". In front of ":","AA" is the
number to match, and what is operated is realized by the following. If it math the rule,
the system will delete the symbol of "aa",and add "bb"; or continue. There is nothing
after the symbol of ":", such as "00:", it means system do nothing and quit when match
the symbol. System will operate directly when no string before symbol of ":", such as
":+86755".
4. There is no limited range for the dialing out rule of the match definition, the language is
"[A-B]A:-aa+bb" or "A[A-B]:-aa+bb".
Template:
1. Rule: "0:|:+0755"
A. input "02083185711" , output "02083185711"
B. input "83185700"
, output "075583185700"
2. Rule: "00:-00|0"-0+86|:+86755"
A. input "008522343318", output "8522343318";
B. input "02083185711", output "862083185711";
C. input "83185700",
output "8675583185700".
3. Rule: "00:|0:-0+0086|:+0086755".
A. input "008522343318", output "008522343318";
B. input "02083185711", output "00862083185711";
C. input "83185700",
output "008675583185700".
4. Rule: "0:|1[3-9]:+0|[2-8]:+0755|:+0755".
A. input "076322343318", output "076322343318";
B. input "13044557766", output "013044557766";
or input "13644557766", output "013644557766"
C. input "23185700",
output "075523185700".
or input "73185700",
output "075573185700"
4.4.7.2 How to limit code bit
If you want to limit the bit of every telephone number in the HT-822P, you could set the dial
rule as follow: "AAXXXXXX:-aa+bb" , "AAXXXXXX" is the description for the matching
35
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
code and it's exact length.
Configuration:
If you set the rule of above example of 3 as follow:
Before: "00:|0:-0+0086|:+0086755".
Now:
"00:|0:-0+0086|[1-8]xxxxxxx:+0086755".
Now, the length of local telephone number is limited in 8 bit ,first bit is range from 1 to 8.
Then the gateway will add 0086755 in front of telephone number and dial out.
The second example:
Rule:
"0:|13:+0|:+0755"
This rule will automatically add "0" before cell phone, and add 0755 before local dial.
Set as follow:
"0:|13[0-9]xxxxxxxx:+0|[1-8]xxxxxxx:+0755"
This rule holds the same function while cell phone number will be limited in 11 bit and local
dial is 8 bit. In the rule, the string of "13[0-9]xxxxxxxx" means the number from
130xxxxxxxx to 139xxxxxxxx while "[1-8]xxxxxxx" means local telephone number from
1xxxxxxx to 8xxxxxxx .
Attention: Once the bit of the number is defined, it will be abandoned when the code is
longer than the definition length
The third example:
Rule:
"0:|13[0-9]xxxxxxxx:+0|[1-8]xxxxxxx:+0755"
We dial out the number "88990011" or "8899001133", and the really we dial is the same
one, which is "075588990011".
Attention:
This rule doesn’t support the gateway of the version before A34HS-3.09-18.
This rule doesn’t support the gateway of the version before A34HS-3.07-18.
4. 5 User Command
The HT-822P have four User Commands, in the “Phone Setting” Web like below screen:
You can change the VoIP and PSTN switch command.
The other two commands:
The Hold Key command:*42
The Transfer Key command;*41
Note: these values are preset by the factory and be cautious to revised.
36
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
4.5.1 Start VoIP dial
The default number is *12. If the line is default PSTN, press *12 and you will switch to
VoIP line.
4.5.2 Switch to PSTN
The default number is *21. If the line default is VoIP, press *21 and you will switch to PSTN
line.
4.5.3 Hold Key
The default number is *42. If you are in the process of a call, press *42 and you will put the
call on hold.
4.5.4 Transfer Key
The default number is *41. If you press *41 in the process of a call, you will transfer the
call to another terminal.
4.5.5 Star Command Input Timeout
While inputting a star command, after inputting “*”, please go on to input the number in a
certain time. If you exceed this time, the system will not wait for your input. The default
value is 60 seconds, these values are preset by the factory and can’t be revised.
4.6 Gain Setting…
The gain setting is cautious to using. It was a hidden web page. If you need to adjust the
phone volume. Please rewrite the URL to http://xxx.xxx.xxx.xxx/default/en_US/gain.html
and enter. The IE wills pop-up a GAIN SETTINGS screen.
You can adjust the volume of the two phones to different values. The range you can adjust
is from 5 to -5.
37
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
Note: The range of the Input Gain can induce the terminal can not dial the phone number. If you
meet this phenomenon and you adjusted it, Please resume or lessen the range of the Input
Gain.
4.7 PhoneBook
The HT-822P can storage 20 phone number. Click on the PhoneBook in the left menu the screen
will display as below.
38
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
User can edit the phonebook and dial up the phone number using the phone book function.
4.8 About FAX
HyberTone Technology Co.,Ltd. Declare the HT-822P nonsupport FAX function. But it was
build-in two type free FAX codes.
Note: HyberTone Technology Co.,Ltd. Declare the HT-822P Gateway are nonsupport FAX
function.
HyberTone Technology Co.,Ltd. don’t supply any FAX support for HT-822P Gateway.
4.9 Network Configurations
Click on Network Configurations in the left menu of the Configuration web and the network
configurations screen will be displayed as below.
39
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
The Network Configurations screen allows you to set up the IP addresses of the LAN and
PC port, Bridge or Router mode (by selecting or deselecting Bridge Mode), default
Gateway Address, and Primary and Secondary DNS server IP addresses. It includes LAN
port configurations and PC port configurations.
4.8.1 LAN Port configurations
The HT-822P LAN port can be configured to obtain its IP address by DHCP or the IP
address can be set statically (used mainly when using the ATA with a DSL line). There are
three modes to configure LAN port: 1) DHCP, 2) Static IP, 3) PPPoE.
1) DHCP
When you connect to the network through DHCP, the ATA is automatically assigned an IP
address by the router. So you can get the LAN port IP address from the DHCP server.
2) Static IP
40
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
In a typical geographically determined network, users input telephone numbers manually.
If you obtain a static IP address from your ISP, you can assign it to the ATA LAN port by
clicking the Static IP Address Manually, and then entering the IP Address, Subnet Mask,
and Default Route.
3) PPPoE
PPPoE, point-to-point protocol over Ethernet, is a network protocol for encapsulating PPP
frames in Ethernet frames. It is used mainly with cable modem and DSL (Digital
Subscriber Line) services. Click PPPOE, and you can set user name and user password.
4). Advance…
Click Advance and you will see the following two items: Hardware address and Broadcast
address.
Hardware Address is an address used to enter the MAC address in XX: XX: XX: XX: XX:
XX format.
Broadcast Address is an address used to communicate with the other computers
connected to the PC side of the ATA.
4.8.2 PC port configurations
PC port is configured to make a connection of the network and ATA. There two modes to
configure a PC port: Bridge Mode and Static IP.
41
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
1) Bridge Mode
In the Bridge Mode, the ATA allows a PC connected to it to pass through to the network.
No other PC Configuration settings are set; the Advanced Settings, Gateway, Primary and
Secondary DNS field settings are not required and will be ignored.
2) Specify an IP Address Manually
Click Static IP, and enter IP Address and Subnet Mask.
3) Enable DHCP Service
To Enable DHCP Service, you have to know the starting address, which is used to start
the service; and the ending address, which is used to end this service. The HT-822P’s
DHCP server must running by PC Port using Static IP mode.
4) Advance…
Click Advance and you will see the following two items: Hardware address and Broadcast
address.
42
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
Hardware Address is an address used to enter the MAC address in XX: XX: XX: XX: XX:
XX format.
Broadcast Address is an address used to communicate with the other computers
connected to the PC side of the ATA.
4.8.3 Primary DNS
DNS is the abbreviation for domain name server, domain name system. A database of
Internet names and addresses that translates the names to the official Internet Protocol
numbers and vice versa; the distributed name-and-address mechanism used in the
Internet. Primary DNS is the primary DNS server IP address. You can obtain this from
your ISP (For example: 202.67.156.221). If PPPoE Dialup Networking is used, the
Primary DNS will be obtained automatically from the ISP. This entry can be left blank.
4.8.4 Secondary DNS
It is the secondary DNS server IP address that will be used in the event that the primary
DNS server IP address fails or is not available. You can obtain this from your ISP (For
example: 202.67.156.222). If PPPoE Dialup Networking is used, the Secondary DNS will
be obtained automatically from the ISP. This entry can be left blank.
4.9 Save Configuration
Once a change is made, users should click on the “Save Configuration” button in the
Configuration page. Otherwise, your configuration will not take effect. The ATA will then
display the following screen to confirm that the changes have been saved.
43
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
4.10 Discard Changes
4.11 Tools Menu
Click on the “Tools”, the web page will pop-up a subordinate options and the screen will be
displayed as follows:
4.11.1 Online Upgrade
WARNING! Performing an online upgrade is for experienced users or administrators only!
Click Online Upgrade. Enter the IP address or domain name of the upgrade server and
package name: http://202.96.136.145/update/A34HS-3.07-18.pkg, And then click Start.
44
Http://www.hybertone.com
HT-822P VoIP FXS+PSTN Gateway
WARNING! When the terminal was updating , please don’t cut the power. It will
destroy the terminal.
4.11.2 Change Password
A) User Password
The ATA supports multiple levels of user administration. The user password is set to allow
you to configure the phonebook and other user administrative tasks. The default is 1234.
You can change it according to your own wish.
B)Administrator Password
The administrator password is set to allow you to modify all configuration items assigned
to the ATA. The default is admin. You can change it according to your own wish..
4.11.3 Reset Configuration
Click on this field to reset the configuration. When you choose this function, the terminal
will auto reboot and all the personal setting will lost. The terminal will restore to the
factory’s setting.
You can use the star command to achieve the function.
45
HT-822P VoIP FXS+PSTN Gateway
Http://www.hybertone.com
4.11.4 Reboot the Device
Click on this field to reboot the device.
5 Products Parameter
Characteristics of the
Parameter
hardware
Remarks
Type
HT-822P
Can be customized
Processor
ARM9E 133MHz
DSP
VPDSP101-2 100MHz
RAM
16M
FLASH
4M
Power
DC24V/500mA
Consumption
The maximum 5 W
LED
Operate, network , circuit
Network card
100/10BASE-T ×2
Weight
180 grams
Working temperature
0-42℃
Working humidity
40%-90% not congealed
Colour
White
FXS port
2
24V feed, 48V shaking bell
PSTN port
1
Relay switching
(WHITOUT AC ADAPTOR)
46
HT-822P VoIP FXS+PSTN Gateway
Http://www.hybertone.com
6 Manufactory Parameter
Parameter
Network
Password
Default
LAN
DHCP
PC
Fixed IP : 192.168.8.1
admin
user
Time Zone
dbl#admin
or admin
1234
GMT+8
The default star command please refer to the table in section 3.1.1 for detailed information.
This default parameter are unsuitability the customization’s products.
47
Download PDF