Culligan | Gold Series | Specifications | Culligan Gold Series Specifications

Culligan
Gold Series™
Automatic
Water Filter
Owners Guide
THANK YOU
AND WELCOME TO YOUR NEW WORLD OF BETTER
LIVING WITH CULLIGAN WATER.
The Culligan Gold Series Cullar® filter has been tested and certified by
WQA against WQA S-200 for the effective reduction of chlorine taste and
odor up to 120,000 gallons for the 9” filter and 180,000 gallons for the 10”
filter.
The Culligan Gold Series Cullneu® filter has been tested and certified by WQA against WQA
S-200 for neutralization up to 14,500 gallons for the 9” Cullneu filter and 21,750 gallons for
the 10” Cullneu filter as verified and substantiated by test data.
The Culligan Gold series FiltrCleer 9” Model has been tested and certified by WQA against
WQA S-200 for Class IV (>5-15µm to <30µm) particulate reductions as verified and
substantiated by test data. The Culligan Gold Series FiltrCleer 10” has not been certified by
WQA.
Do not use with water that is microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system.
For installations in Massachusetts, the Commonwealth of Massachusetts Plumbing
Code 248 CMR shall be adhered to. Consult your licensed plumber for installation of
the system. This system and its installation must comply with state and local regulations.
If this is your first experience having filtered, conditioned water in your home, you’ll be
amazed at the marvelous difference it makes. We promise that you’ll never want to be
without it again.
Congratulations, too, on selecting one of the “first family” of water filters in the
prestigious Culligan Gold Series. With Culligan’s many years of knowledge and experience
in water treatment, you can be confident that the model you selected has been designed and
engineered to provide years of service with a minimum of care and attention.
i
Products manufactured and marketed by Culligan International Company (Culligan) and its affiliates are protected by
patents issued or pending in the United States and other countries. Culligan reserves the right to change the specifications
referred to in this literature at any time, without prior notice. Culligan, Culligan Gold Series, Cullar, Filtr-Cleer, Cullneu,
Accusoft, Culligan Man and www.culligan.com are trademarks of Culligan International Company or its affiliates.
Performance Data Sheets are included in this manual for the various Culligan Gold Series Filter
models. Refer to the Performance Data Sheet for your specific filter, as there are slight differences
between the models. The filter warranty is located on page 12 of this Owner’s Guide.
Culligan Gold Series 9” Cullar Filter & 10” Cullar Filter
Performance Data Sheet - Page 8
Culligan Gold Series 9” Cullneu Filter & 10” Cullneu Filter
Performance Data Sheet - Page 9
Culligan Gold Series 9” Filtr-Cleer Filter & 10” Filtr-Cleer Filter
Performance Data Sheet - Page 10
1
Specifications
2
9-INCH
10-INCH
GENERAL
Mineral Tank Size
Control
Timer
Temperature Limits
Water Pressure Limits
Water Pressure Limits (Canada)
Electrical Requirements
Electrical Power Consumption, Min./Max.
Overall Height
9x48 in. (229x1,219mm)
Hi-Flo Power Valve
Electronic
33-120°F (1-50°C)
20-120 psi (140-860kPa)
20-90 psi (140-620kPa)
24V/50-60 Hz
3 Watts/35 Watts
54 in. (1,372 mm)
10x54 in. (254x1,372mm)
Hi-Flo Power Valve
Electronic
33-120°F (1-50°C)
20-120 psi (140-860kPa)
20-90 psi (140-620kPa)
24V/50-60 Hz
3 Watts/35 Watts
60 in. (1,524 mm)
FILTR-CLEER5
Rated Service Flow @ Pressure Drop
Minimum Practical Filtration Size
Maximum Particulate Matter
Maximum Suspended Solids
Drain Flow, Maximum1
pH Limitation
Recharge Time2
Recharge Water Consumption, Av.3
Freeboard4
9.0 gpm @ 8 psi
15 microns
150 NTU
150 mg/L
4.5 gpm
6.0 - 9.5
30 min.
90 gal.
20 ± 1.5 inches
12.0 gpm @ 15 psi
15 microns
150 NTU
150 mg/L
7.0 gpm
6.0 - 9.5
30 min.
140 gal.
19 ± 1.5 inches
CULLAR
Rated Service Flow @ Pressure Drop
Drain Flow, Maximum1
pH Limitation
Recharge Time2
Recharge Water Consumption, Av.3
Cullar Media Volume
Cullsan® Underbedding Media Amount
Freeboard4
Rated Capacity
4.0 gpm @ 2.0 psi
3.5 gpm
5.0 - 11.0
30 min.
40 gal.
0.75 cu. ft.
10 lbs. (.1 ft3)
22 ± 1.5 inches
120,000 gallons
6.0 gpm @ 6.0 psi
5.5 gpm
5.0 - 11.0
30 min.
110 gal.
1.5 cu. ft.
20 lbs. (.2 ft3)
24 ± 1.5 inches
180,000 gallons
CULLNEU
Rated Service Flow @ Pressure Drop
Drain Flow, Maximum1
pH Limitation*
Recharge Time2
Recharge Water Consumption, Av.3
Cullneu Media Volume
Freeboard4
Rated Capacity
4.0 gpm @ 1.0 psi
3.5 gpm
5.2 to ³ 6.8
30 min.
70 gal.
1.1 cu. ft.
13 ± 1.5 inches
14,500 gallons
6.0 gpm @ 5.0 psi
5.5 gpm
5.2 to ³ 6.8
30 min.
110 gal.
1.6 cu. ft.
18 ± 1.5 inches
21,750 gallons
1
2
3
4
5
*
Backwash at 120 psi (830 kPa).
Factory Settings.
Factory Settings and 120 psi line pressure.
Measured from top of media surface to top surface of tank threads (backwashed and drained).
The Filtr-Cleer 10” filter data has not been certified by WQA.
NOTE: Under dynamic conditions, it may be necessary to mix five parts Cullneu with one part Cullneu C to effectively raise the pH.
Familiarization
Display
As shipped from the factory, the display of the board will turn off if there has been no
keyboard activity for a 1 minute period. To have the display constantly lit, press the STATUS button until
the number 10 icon is lit. Next, press the UP arrow. A “d” for disable will appear in the display. To have the
display blank again, press the UP arrow. An “E” will appear in the display.
Power Loss
The AccuSoft® circuit board is equipped with a Hi-Cap Capacitor and EEPROM memory chip. The
capacitor is capable of maintaining the time, for at least one day, in the event of a power outage. The
EEPROM ensures that the individual programming parameters of your filters are not lost.
If the power outage lasts long enough to drain the Hi-Cap Capacitor, the control will flash “12:00 PM”
when power is returned to the control. The unit will continue to keep time from the moment power is
restored, and will initiate a full regeneration at the preset regeneration time. The time of day will need to
be reset in order to return the regeneration to its preset time.
If you live in an area where power outages occur with a regular frequency, a battery backup option is
available for ensuring that the time of day is properly maintained. Contact your Culligan Dealer for more
information.
Regeneration
To initiate an immediate regeneration, press the “REGEN” button twice. The first time the
“REGEN” will light and the second time the motor will run and the “REGEN” will begin to
blink. An immediate regeneration will also occur if a power outage has lasted for more than
four hours and the Immediate Regeneration option is chosen. Ask your Culligan Dealer
about this feature.
Service
The Culligan Gold Series filters are equipped with a self diagnostic program to insure optimal operation
of your filter. Should service become necessary, a phone icon will appear in the display. If this condition
occurs, call your local Culligan Dealer for assistance. The phone icon will be the only item displayed when
service is required on the control.
3
Programming
The Culligan AccuSoft® circuit board controls all of the filter functions. These settings are
programmed at the time of installation. The following is a list of all the microprocessor functions, in the event that any of the settings need to be adjusted. If a small padlock icon appears in
the lower right corner of the display, the microprocessor settings are locked and only the Timeof-Day setting can be adjusted, call your Culligan Dealer if setting changes are required.
1. With a flashing or blank display, pressing the
status button twice will move to the Time-of-Day
adjustment. A number “1” will appear at the bottom
of the display while in this mode.
Press ▲ to increase or
▼ to decrease
2 . Press status again, this displays the Time-ofRegeneration. A number “2” will appear at the
bottom of the display while in this mode.
Press ▲ to increase or
▼ to decrease
3 . Press status again, the number at the bottom of
the display will skip to “4”. This setting is not
used.
4 . Press status again, this displays the Backwash
Time. The setting can be adjusted between 5
and 40 minutes. A number “5” will appear at the
bottom of the display while in this mode.
5 . Press status again to display the Pause Time.
This setting can be adjusted from 1-15 minutes.
A number “6” will appear at the bottom of the
display while in this mode.
Press ▲ to increase or
▼ to decrease
Press ▲ to increase or
▼ to decrease
6. Press status again to display the Fast Rinse Time. This
setting can be adjusted from 5-30 minutes. A number
“7” will appear at the bottom of the display while in
this mode.
P r e s s ▲ to increase or
▼ to decrease
4
7. Press status again will show the Regeneration Interval.
This setting can be adjusted from 1-42 days. A number
“8” will appear at the bottom of the display while in
this mode.
Press ▲ to increase or
▼ to decrease
8. Press status again, the number “9” will appear at the
bottom of the display. This setting is not used.
9. Pressing status again brings up the ability to Enable/
Disable the screen blanking. To have the display
constantly lit, press the up arrow, a “d” for disable will
appear in the display. Pressing the up arrow again
displays an “E”, signifying that display blanking is
enabled. A number “10” will appear at the bottom of
the display while in this mode.
Press ▲ to change
5
Things to Check Before You Call For Service
If you unexpectedly experience unfiltered water, make these simple checks before calling
your Culligan dealer. One of the following conditions may be the reason for your interruption
of service.
IMPORTANT
If any of the following conditions are found, the water filter should be manually recharged
according to instructions on page 3 after you have corrected the problem.
POWER SUPPLY
Check your power supply cord. Is it plugged fully into the electric outlet? Be certain that the outlet is not
controlled by a wall switch which has been turned off. Reset the filter to proper time of day.
BLOWN FUSE
Check the house fuse or circuit breaker panel. Replace a blown-out fuse or reset an open circuit breaker.
POWER FAILURE
Any interruption in your power supply or time changes - such as daylight savings - will disrupt your
conditioner’s recharge schedule by causing the timer to run off-schedule. Reset timer to proper time of
day.
BYPASS VALVES
Check to see if they are in the proper position. Cul-Flo-Valv® Bypass, if used, should be in the “Push for
Service” position. If hand valves are used, see that inlet and outlet valve are opened and that the bypass
valve is closed.
NO WATER
If you aren’t getting any water flow at all, make sure your water supply is working. Open a
tap ahead of the filter (outside tap) to see if you have any water pressure. If you have water
pressure, check the bypass valve. If it is in the Service position, put it into the bypass and
call your Culligan dealer for service.
INCREASED USAGE
Guests, family additions, new water-using appliances, etc., all will result in more water usage and will
require more capacity from your filter. You can reprogram your recharging schedule by
following the directions on pages 4 and 5. Call your Culligan dealer for advice and save a
service call.
6
When and How to Bypass Your Water Filter
Normally, all water except outside lines passes through the water filter. There are
times when the water filter should be bypassed, using the push-button Cul-Flo-Valv Bypass, or a
3-way bypass valve. You should bypass:
1 . If lines to outside faucets do not bypass the water filter, and you do not want
to waste filtered water on lawn sprinkling or other outside uses.
2 . If you are going away on vacation and want to save water by not having the unit
recharge while you are away.
PUSH-BUTTON BYPASS
In the back of Culligan water filter is a push-button Cul-Flo-Valv Bypass. To bypass unit, simply
push the red knob (marked “Push to Bypass”) against the bypass valve body. To return to filtered
water service, reverse the procedure - push the blue knob (marked “Push for Service”) against
the bypass valve body.
7
Performance Data Sheet
Culligan knows the more informed you are about your water treatment systems, the more
confident you will be about its performance. It’s because of this and more than sixty years
of commitment to customer satisfaction that Culligan is providing this Performance Data
Sheet to its customers.
IMPORTANT NOTICE: Read this Performance Data Sheet and compare the capabilities of
this unit with your actual water treatment needs. It is recommended that before purchasing
a water treatment unit, you have your water supply tested to determine your actual water
treatment needs.
MANUFACTURER:
Culligan International Company,
One Culligan Parkway, Northbrook, IL 60062-6209 USA
(847) 205-6000
PRODUCT: Culligan Gold Series 9” Cullar & 10” Cullar Filter
TESTING CONDITIONS & RESULTS:
Capacity:
120,000 gallons for the 9” Filter
Pressure: 60 psi
180,000 gallons for the 10” Filter
Temperature: 63°-73°F (17°-23°C)
pH: 7.6
Service Flow: 4.0 gpm @ 2.0 psi for the 9” Filter
6.0 gpm @ 6.0 psi for the 10” Filter
OPERATING CONDITIONS:
Operating Temperature Range: 33 - 120°F (1 - 50°C)
Water Pressure Range: 20 - 120 psi (140 - 860 kPa)
Water Pressure Range: (Canada): 20-90 psi (140-620 kPa)
Electrical Characteristics: 24V/50-60 Hz, 45 Watts
SUBSTANCE REDUCTION
While testing was performed under standard laboratory conditions, actual performance may vary.
Model
Substance
USEPA SDWA Average % Minimum %
Avg Test Influent
Avg Test Effluent
MCL
Reduction Reduction Concentration Level Concentration Level
9” Cullar
Chlorine Taste and Odor
N/A
98.7
98.1
2.66 mg/L
0.05 mg/L
10” Cullar
Chlorine Taste and Odor
N/A
98.9
98.6
2.11 mg/L
0.02 mg/L
The Culligan Gold Series Cullar filter has been tested and certified by WQA against WQA S-200 for the effective
aesthetic reduction of chlorine taste and odor up to 120,000 gallons for the 9” filter and 180,000 gallons for the
10” filter. The system has been tested according to NSF/ANSI 42 for the reduction of the substances listed. The
concentration of the indicated substances in water entering the system was reduced to a concentration less than
or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42.
Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be
backwashed. If conditions do not improve, contact your local Culligan Man™. He can determine if your filter
requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system. Refer to the specifications and warranty sections of this owners
guide for more specific product information.
8
To avoid contamination from improper handling and installation, your system should only be installed and
serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced
by this product are not necessarily in your water.
Performance Data Sheet
Culligan knows the more informed you are about your water treatment systems, the more
confident you will be about its performance. It’s because of this and more than sixty years
of commitment to customer satisfaction that Culligan is providing this Performance Data
Sheet to its customers.
IMPORTANT NOTICE: Read this Performance Data Sheet and compare the capabilities of
this unit with your actual water treatment needs. It is recommended that before purchasing
a water treatment unit, you have your water supply tested to determine your actual water
treatment needs.
MANUFACTURER:
Culligan International Company,
One Culligan Parkway, Northbrook, IL 60062-6209 USA
(847) 205-6000
PRODUCT: Culligan Gold Series 9” Cullneu & 10” Cullneu Filter
TESTING CONDITIONS & RESULTS:
Capacity:
Gallons 9” Filter:: 14,500
Gallons 10” Filter:: 21,750
Rated Service Flow:
4.0 gpm @ 1.0 psi (9” Filter)
Pressure: 60 psi
Temperature:: 76°-78°F (24°-25°C)
pH:: 4.9 - 5.5
6.0 gpm @ 5 psi (10” Filter)
OPERATING CONDITIONS:
Operating Temperature Range: 33 - 120°F (1 - 50°C)
Water Pressure Range: 20 - 120 psi (140 - 860 kPa)
Water Pressure Range: (Canada): 20-90 psi (140-620 kPa)
Electrical Characteristics: 24V/50-60 Hz, 45 Watts
SUBSTANCE REDUCTION
While testing was performed under standard laboratory conditions, actual performance may vary.
Model
Substance
USEPA SDWA Average % Minimum %
Avg Test Influent
Avg Test Effluent
MCL
Reduction Reduction Concentration Level Concentration Level
9” Cullneu
pH
6.5 - 8.5
N/A
N/A
5.24 mg/L
>6.8 mg/L
10” Cullneu
pH
6.5 - 8.5
N/A
N/A
4.6 mg/L
>7.1 mg/L
The Culligan Gold Series Cullar filter has been tested and certified by WQA against WQA S-200 for neutralization up to 14,500 gallons for the 9” filters and 21,750 gallons for the 10” filters as verified and substantiated by
test data. The system has been tested according to NSF/ANSI 42 for the reduction of the substances listed. The
concentration of the indicated substances in water entering the system was reduced to a concentration less than
or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42.
Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be
backwashed. If conditions do not improve, contact your local Culligan Man™. He can determine if your filter
requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system. Refer to the specifications and warranty sections of this owners
guide for more specific product information.
To avoid contamination from improper handling and installation, your system should only be installed and
serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced
by this product are not necessarily in your water.
9
Performance Data Sheet
Culligan knows the more informed you are about your water treatment systems, the more confident you
will be about its performance. It’s because of this and more than sixty years of commitment to customer
satisfaction that Culligan is providing this Performance Data Sheet to its customers.
IMPORTANT NOTICE: Read this Performance Data Sheet and compare the capabilities of
this unit with your actual water treatment needs. It is recommended that before purchasing
a water treatment unit, you have your water supply tested to determine your actual water treatment
needs.
MANUFACTURER:
Culligan International Company,
One Culligan Parkway, Northbrook, IL 60062-6209 USA
(847) 205-6000
PRODUCT: Culligan Gold Series 9” Filtr-Cleer & 10” Filtr-Cleer Filter
TESTING CONDITIONS & RESULTS:
Rated Service Flow:
9.0 gpm @ 8.0 psi for the 9” Filter
12.0 gpm @ 15.0 psi for the 10” Filter
Pressure: 60 psi
Temperature:: 76°-78°F (24°-25°C)
pH: 4.9-5.5
OPERATING CONDITIONS:
Operating Temperature Range: 33 - 120°F (1 - 50°C)
Water Pressure Range: 20 - 120 psi (140 - 860 kPa)
Water Pressure Range (Canada): 20-90 psi (140 - 620 kPa)
Electrical Characteristics: 24V/50-60 Hz, 45 Watts
SUBSTANCE REDUCTION
While testing was performed under standard laboratory conditions, actual performance may vary.
Model
Substance
9” Filtr-Cleer Class IV Particulate >15 um to <30 um
Avg Test Effluent
Reduction
Challenge Concentration Required
12,726 particles/mL
>85%
Average %
Reduction
Minimum %
Reduction
90%
85%
The Culligan Gold Series Filter-Cleer 9” filter has been tested and certified by WQA against WQA S-200 for Class
IV (>15um to < um) particulate reduction as verified and substantiated by test data. The Culligan Gold series
Filter-Cleer 10” filter has not been tested or certified by WQA. The 9” filter system has been tested according to
NSF/ANSI 42 for the reduction of the substances listed. The concentration of the indicated substances in water
entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving
the system, as specified in NSF/ANSI 42.
Performance Indicator: If water flow decreases or a noticeable taste change occurs, the filter should be
backwashed. If conditions do not improve, contact your local Culligan Man™. He can determine if your filter
requires servicing. Do not use with water that is microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system. Refer to the specifications and warranty sections of this owners
guide for more specific product information.
To avoid contamination from improper handling and installation, your system should only be installed and
serviced by your Culligan Man. Performance will vary based on local water conditions. The substances reduced
by this product are not necessarily in your water.
10
Records and Data
Important Data on Your Water Filter
It is advisable to have the salesperson or installer fill in the information below for your future
reference. If this has not been done, please ask for it, as it is necessary if you contact your dealer.
IDENTIFICATION
Model Name ________________________ Catalog No. ___________________________
Control Model No. ____________________ Control Serial No. ______________________
Date of Installation ___________________ Tank Serial No. ________________________
SETTINGS
Time of Recharge: ________ a.m. ________p.m.
Regeneration Interval ________ days
Number of people in household
____________________________________________________________
WATER ANALYSIS
Total Hardness ________ (gpg)
Total Iron ________ (ppm)
pH (acidity)__________
Other
________________________________________________________________________________
_____________________________________________________________________________________
11
Culligan Limited Warranty
CULLIGAN GOLD SERIES AUTOMATIC WATER FILTERS
You have just purchased one of the finest water filter made. As an expression of our confidence in
Culligan International Company products, your water filter is warranted to the original end-user, when
installed in accordance with Culligan specifications, against defects in material and workmanship
from the date of original installation, as follows:
For a period of ONE YEAR
For a period of FIVE YEARS
For a period of TEN YEARS
For the LIFETIME of the
original consumer purchaser
The entire filter
The control valve timer
The AccuSoft® circuit board
The control valve body, excluding internal parts
The Quadra-Hull® conditioner tank
If a part described above is found defective within the specified period, you should notify your independently operated Culligan dealer and arrange a time during normal business hours for the dealer to inspect
the water conditioner on your premises. Any part found defective within the terms of this warranty will be
repaired or replaced by the dealer. You pay only freight from our factory and local dealer charges.
We are not responsible for damage caused by accident, fire, flood, freezing, Act of God, misuse,
misapplication, neglect, oxidizing agents (such as chlorine, ozone, chloramines and other related components), alteration, installation or operation contrary to our printed instructions, or by the use of accessories
or components which do not meet Culligan specifications, is not covered by this warranty. Refer to the
specifications section in the Installation and Operating manual for application parameters.
Our product performance specifications are furnished with each water conditioning unit. TO THE EXTENT
PERMITTED BY LAW, CULLIGAN DISCLAIMS ALL IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE; TO
THE EXTENT REQUIRED BY LAW, ANY SUCH IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE ONE-YEAR PERIOD SPECIFIED ABOVE FOR THE ENTIRE CONDITIONER. As a manufacturer, we do not know the characteristics of your water supply or the purpose for which you are purchasing
a water conditioner. The quality of water supplies may vary seasonally or over a period of time, and your
water usage rate may vary as well. Water characteristics can also differ considerably if your water conditioner is moved to a new location. For these reasons, we assume no liability for the determination of the
proper equipment necessary to meet your requirements, and we do not authorize others to assume such
obligations for us. Further, we assume no liability and extend no warranties, express or implied, for the
use of this product with a non-potable water source. OUR OBLIGATIONS UNDER THIS WARRANTY ARE
LIMITED TO THE REPAIR OR REPLACEMENT OF THE FAILED PARTS OF THE WATER CONDITIONER,
AND WE ASSUME NO LIABILITY WHATSOEVER FOR DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, SPECIAL, GENERAL, OR OTHER DAMAGES.
Some states do not allow the exclusion of implied warranties or limitations on how long an implied
warranty lasts, so the above limitation may not apply to you. Similarly, some states do not allow the
exclusion of incidental or consequential damages, so the above limitation or exclusion may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state. Consult your telephone directory for your local independently
operated Culligan dealer, or write Culligan International Company for warranty and service
information.
CULLIGAN INTERNATIONAL COMPANY
One Culligan Parkway
Northbrook, Illinois 60062
12
With Culligan You Get More Than a Quality Product
You Get Your Water Expert, The Culligan Man
We’re here to provide you with fast, dependable service, making sure any problems you have are
taken care of. The Culligan Man has been around for over sixty years, delivering quality products
and dependable service all along. That’s why people say “Hey, Culligan Man!®” Because we’re the
water experts. And that’s who you want taking care of your water.
The Culligan Promise
At Culligan, we understand that a water quality improvement system is an investment in your
family’s well-being. That’s why our 1,350 independently operated dealers worldwide don’t just
sell products; they sell water quality you can count on. We stand behind our products with
written limited warranties and our unequaled Culligan service. No matter where you live, you
can depend on Culligan expertise to work for you — today and tomorrow.
01016686A
©2003 Culligan International Company
Printed in USA
13
Download PDF