INSTALLATION GUIDE CURRENT MONITORING TM H739 TM 739 Solid-Core Current Switch, Adjustable Trip Point With Command Relay, 120 VAC/DC Status Output Installer’s Specifications Amperage Range 1-135 A continuous Sensor Power Induced from monitored current Insulation Class 600 VAC RMS Frequency Range 50/60 Hz Temperature Range-15° to 60°C (5° to 140°F) Humidity Range 10-90% RH non-condensing Hysteresis 10% of setpoint, typical Terminal Block Maximum WIre Size 14 AWG Terminal Block Torque (nominal) 4 in-lbs (0.45 N-m) Status Output N.O. 0.2 [email protected] VAC/DC Relay Coil 24 VAC/DC, 10 mA Relay Contact Resistive: 10 [email protected] VAC, 30 VDC; Inductive: 5 [email protected] VAC, 30 VDC Agency Approvals UL508 E150462 Do not use the LED status indicators as evidence of applied voltage. The product design provides for basic insulation only. DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH • • • • • Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes. This equipment must only be installed and serviced by qualiﬁed electrical personnel. Read, understand and follow the instructions before installing this product. Turn oﬀ all power supplying equipment before working on or inside the equipment. Use a properly rated voltage sensing device to conﬁrm power is oﬀ. DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION • Only install this product on insulated conductors. Failure to follow these instructions will result in death or serious injury. NOTICE • • • • This product is not intended for life or safety applications. Do not install this product in hazardous or classiﬁed locations. The installer is responsible for conformance to all applicable codes. Mount this product inside a suitable ﬁre and electrical enclosure. WIRING EXAMPLE INSTALLATION Disconnect and lock out power to the enclosure containing the conductor to be monitored. 1. Locate a mounting surface for the removable mounting bracket that will allow the monitored conductor to pass through the center window when it is installed and that will keep the device at least 1/2” from any uninsulated conductors. Determine cable routing for the controller connection, allowing wiring to reach the mounting location. 2. Route the conductor through the sensor’s center window and slip the assembly into the mounting bracket. Terminate the conductor. See Notes (page 2) for currents under 1 Amp or above 135 Amps. 3. Wire the output connections to the DDC controller or switched load (solid state contact). 4. Secure enclosure and reconnect power. 5. Calibrate the sensor (see Calibration section). DIMENSIONS CONTROLLER Removable/Adjustable Mounting Bracket DI (Status) DO (Relay 0.9" (23 mm) 0 0.7" (19 mm) Coil) 3.0" (75 mm) 2.8" (68 mm) CONTACTOR Fan or Pump CONTROL POWER Motor Z201490-0A PAGE 1 1.1" (27 mm) 0.2” x 0.15” slot (2x) 3.8" (95 mm) 4.2" (106 mm) ©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 01121 Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries. INSTALLATION GUIDE H739 TM OPERATION CALIBRATION The H739 is a current-sensitive switching device that monitors current (amperage) in the conductor passing through it. A change in the conductor’s amperage that crosses the adjustable switch threshold plus the hysteresis value causes the resistance of the FET status output to change state, similar to the action of a mechanical switch. In this model, the setpoint is adjustable through the action of a twenty (20) turn potentiometer (see the CALIBRATION section). An integrated relay allows start/ stop control. The status output is suitable for connection to building controllers or other appropriate data acquisition equipment operating at up to 120 volts. The H739 requires no external power supply to generate its output. Before beginning calibration, establish normal load conditions. NOTES For load currents greater than sensor maximum rating: Use a 5 Amp (H68xx series) Current Transformer (CT) as shown. This technique can be combined with wrapping (see below) to add range for a low current load on a high current source. > 135 A (Sensor max.) 240A OK! OK! A Then choose either A or B below. A. To monitor under-current (belt loss, coupling shear, status) ! STATUS OK! OK! A Status Open Setpoint 1. Turn setpoint screw clockwise until Status OPEN LED turns ON. STOP 2. Slowly turn the screw counter‑clockwise until the Status CLOSED LED just turns ON. 3. Turn the screw an Setpoint Status Setpoint Closed additional 1/4 turn counter‑clockwise for 1/4 operational margin. + STOP 300A:5A H68xx-5A CT DANGER: 5A CTs can present hazardous voltages. Install CTs in accordance with manufacturer's instructions. Terminate the CT secondary before applying current. B. To monitor over-current (mechanical problems, seized impeller) STATUS ! OK! OK! A 1. Turn setpoint screw counter‑clockwise until Status CLOSED LED turns ON. CAUTION RISK OF EQUIPMENT DAMAGE Status Setpoint Closed • Derate the product’s maximum current for the number of turns through the sensing window using the following formula. Rated Max. Amps ÷ Number of Turns = Max. monitored Amps e.g. : 100A ÷ 4 Turns = 25 Amps max. in monitored conductor • Failure to follow these instructions can result in overheating and permanent equipment damage. STOP 2. Slowly turn the setpoint screw clockwise until the Status OPEN LED just turns ON. Status Open Setpoint For load currents less than sensor minimum rating: STOP Wrap the monitored conductor through the center window and around the sensor body to produce multiple turns. This increases the current measured by the transducer. < 1 A (Sensor Min.) 4x 0.5A Z201490-0A PAGE 2 + Setpoint 1/4 3. Turn the setpoint screw an additional 1/4 turn clockwise for operational margin. TROUBLESHOOTING Problem Solution No Reading at Controller • Check sensor calibration (see above) • Check for control voltage at sensor (<120 V) • Check for amperage in monitored conductor (>1 A) Setpoint screw has no stops The setpoint screw has a slip-clutch at both ends of its travel to avoid damage. Twenty turns CCW will reset the sensor to be most sensitive. Repeat calibration above. Both LEDs are lit Setpoint screw is too far clockwise. See solution above. ©2012 Veris Industries USA 800.354.8556 or +1.503.598.4564 / [email protected] 01121 Alta Labs, Enercept, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘V’ logo are trademarks or registered trademarks of Veris Industries, L.L.C. in the USA and/or other countries.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project