Apex Digital | PD-650S | Sinamics G110 brochure (563.6 kB )

SINAMICS G110
SINAMICS G110, frame sizes A, B, C
SINAMICS G110, frame size A
with flat plate heatsink
Overview
SINAMICS G110 is a frequency inverter with basic functions
for a variety of industrial variable-speed drive applications.
The particularly compact SINAMICS G110 inverter operates
with voltage frequency control on single-phase supplies
(200 V to 240 V).
It is the ideal low-cost frequency inverter solution for the
lower power range of the SINAMICS family.
Page 1/12
SINAMICS G110
Benefits
Area of application
• Easy to install, parameterize and commission
SINAMICS G110 is especially suited for use with pumps
and fans, or as a drive in various industrial sectors, such as
the food, textile and packaging industries, as well as for
conveyor systems, factory gate and garage door drives, and
as a universal drive for moving billboards.
• rugged EMC design
• comprehensive range of parameters enabling
configuration for a wide range of applications
• simple cable connection
• scaleable functionality due to analog and USS variants
• high pulse frequencies for low-noise motor operation
• status information and alarm messages with the optional
Basic Operator Panel (BOP)
Design
• time saving parameter cloning with optional Basic
Operator Panel (BOP)
The inverters of the SINAMICS G110 family have been built
around the control unit and CPM 110 power module giving
them a compact and efficient design. The inverters use
latest IGBT technoloy and digital microprocessor control.
• external options for PC communications and Basic
Operator Panel (BOP)
The SINAMICS G110 inverter family consists of the
following variants and versions:
• careful handling of the machine mechanical system due to
a skip frequency band in case of resonance,
parameterizable ramp up/ramp down times up to 650 s,
ramp smoothing, as well as bringing the inverter into
circuit on turning motor (flying start)
• Analog variant available in the following versions:
- unfiltered, with heatsink
- integrated EMC Class A/B filter, with heatsink
- unfiltered, with flat plate heatsink (FS A only)
- integrated EMC Class B filter, with flat plate heatsink
(FS A only).
• increasing the installation availability by automatic restart
facility following power failure or fault
• fast current limit (FCL) for trip-free operation in case of
sudden load changes
• fast, repeatable digital input response time for fast
reaction applications
• fine speed adjustment using a high resolution 10-bit
analog input (analog variant only)
• LED for status information
• versions with internal EMC filters Class A or B
• DIP switch for easy setting of 50 Hz or 60 Hz applications
• DIP switch for easy bus termination on the RS485 USS
variant
• RS485 serial interface (USS variants only) facilitates
connection to a networked drive system.
Accessories (overview)
• Low leakage EMC Class B filter
• supplementary EMC Class B filter
• line reactors
• Basic Operator Panel BOP
• DIN rail mounting kit (FS A)
• PC to inverter connection kit
• software commissioning tool STARTER.
International standards
• Complies with the requirements of the EC
low-voltage directive
• CE marking
• UL and cUL listed
• c-tick.
Page 2/12
• USS variant (RS485) available in the following versions:
- unfiltered, with heatsink
- integrated EMC Class A/B filter, with heatsink
- unfiltered, with flat plate heatsink (FS A only)
- integrated EMC Class B filter, with flat plate heatsink
(FS A only).
Cooling is achieved on FS A by a heatsink and natural
convection. The FS A flat plate version offers space saving
and favourable thermal heat dissipation by putting an
additional heatsink outside the electrical cabinet enclosure.
On FS B and FS C an integrated fan is used to cool the
heatsink, this allows the compact design to be achieved.
The connections on all versions of the inverter are easily
accessible and conform to the standard layout. The mains
and motor connections are separated for optimum
electromagnetic compatibility and clear connection (as with
contactors). The control terminal strip has a screwless
design.
The optional Basic Operator Panel BOP can be fitted
without the need for tools.
SINAMICS G110
Technical data
Input voltage and power ranges
200 V to 240 V 1 AC ±10 %
Input frequency
47 Hz to 63 Hz
Output frequency
0 Hz to 650 Hz
0.12 kW to 3.0 kW
cos phi
≥ 0.95
Inverter efficiency
Inverters < 0.75 kW
90 % to 94 %
Inverters ≥ 0.75 kW
≥ 95 %
Overload capability
Overload current 1.5 x rated output current
(i.e. 150 % overload capability) for 60 s,
then 0.85 x rated output current for 240 s,
cycle time 300 s
Inrush current
less than rated input current
Control method
linear V/f characteristic (with programmable voltage boost);
quadratic V/f-characteristic;
multipoint characteristic (programmable V/f characteristic)
Pulse frequency
8 kHz (standard)
Fixed frequencies
3, programmable
Skip frequency band
1, programmable
Setpoint resolution
2 kHz to 16 kHz (in 2 kHz steps)
0.01 Hz digital
0.01 Hz serial
10 bit analog (motor potentiometer 0.1 Hz)
Digital inputs
3 programmable digital inputs, non isolated; PNP type,
SIMATIC compatible
Analog input (analog variant)
1, for setpoint
(0 V to 10 V, scaleable or for use as 4th digital input)
Digital output
1 isolated optocoupler output
(24 V DC, 50 mA, resistive, NPN type)
Serial interface (USS variant)
RS485, for operation with USS protocol
Motor cable length
max. 25 m (shielded)
max. 50 m (unshielded)
Electromagnetic compatibility
all devices with internal EMC filter for power drive systems in
category C2 installations (restricted availability),
limit complies with EN 55 011, Class A, Group 1
furthermore all filtered devices with shielded
cables with a max. length of 5 m comply with the
limits of EN 55 011, Class B
Braking
DC braking
Protection level
IP 20
Temperature range
-10 °C to +40 °C
Storage temperature
-40 °C to +70 °C
Humiditiy
95 % (non-condensing)
Operational altitude
up to 1000 m above sea level without derating
to +50 °C with derating
• Rated output current
at 4000 m above sea level: 90 %
• Mains voltage
up to 2000 m above sea level: 100 %
at 4000 m above sea level: 75 %
Protection features for
under-voltage, over-voltage, earth faults, short circuits, stall
prevention, I2t motor thermal protection, inverter overtemperature, motor over-temperature
Conformity with standards
UL, cUL, CE, c-tick
CE marking
conformity with EC low-voltage directive 73/23/EC
Dimensions and weights
Frame size
HxWxD
Weight, approx. (kg)
(without options)
(FS)
mm
without filter
with filter
A ≤ 0.37 kW
150 x 90 x 116
0.7
0.8
Page 3/12
A 0.55 kW and 0.75 kW
150 x 90 x 131
0.8
0.9
A ≤ 0.37 kW with flat plate
150 x 90 x 101
0.6
0.7
A 0.55 kW and 0.75 kW with flat plate
150 x 90 x 101
0.7
0.8
B 1.1 kW and 1.5 kW
160 x 140 x 142
1.4
1.5
C 2.2 kW
181 x 184 x 152
1.9
2.1
C 3.0 kW
181 x 184 x 152
2.0
2.2
SINAMICS G110
Derating data
Pulse frequency
Rated output
Rated output current in A
for a pulse frequency of
kW
2 kHz
4 kHz
6 kHz
8 kHz
10 kHz
12 kHz
14 kHz
16 kHz
0.12
0.9
0.9
0.9
0.9
u. p.
u. p.
u. p.
u. p.
0.25
1.7
1.7
1.7
1.7
u. p.
u. p.
u. p.
u. p.
0.37
2.3
2.3
2.3
2.3
u. p.
u. p.
u. p.
u. p.
0.55
3.2
3.2
3.2
3.2
u. p.
u. p.
u. p.
u. p.
0.75 (at 40 °C)
3.9
3.9
3.9
3.9
u. p.
u. p.
u. p.
u. p.
0.75
u. p.
u. p.
u. p.
u. p.
u. p.
u. p.
u. p.
u. p.
1.1
6.0
6.0
6.0
6.0
u. p.
u. p.
u. p.
u. p.
1.5 (at 40 °C)
7.8
7.8
7.8
7.8
u. p.
u. p.
u. p.
u. p.
1.5
u. p.
u. p.
u. p.
u. p.
u. p.
u. p.
u. p.
u. p.
2.2
11.0
11.0
11.0
11.0
u. p.
u. p.
u. p.
u. p.
3.0 (at 40 °C)
13.6
13.6
13.6
13.6
u. p.
u. p.
u. p.
u. p.
3.0
u. p.
u. p.
u. p.
u. p.
u. p.
u. p.
u. p.
u. p.
The current data apply to an ambient temperature of 50 °C
unless otherwise specified.
Page 4/12
u. p. = under preparation
SINAMICS G110
Conformity with standards
CE marking
The SINAMICS G110 inverters comply with the
requirements of the low-voltage directive, 73/23/EEC.
A certificate can be provided on request.
Low-voltage directive
The inverters comply with the following standards listed in
the official EU journal:
• EN 60 204
Safety of machinery, electrical equipment of machines
• EN 50 178
Electronic equipment in electrical power installations.
Machinery directive
The inverters are suitable for installation in machines.
Compliance with the machinery directive 89/392/EEC
requires a separate certificate of conformity. This must be
issued by the firm which constructs the plant or puts the
machine on the market.
EMC directive
• EN 61 800-3
Adjustable speed electrical power drive systems
Part 3: EMC product standard including specific test
methods.
The modified EMC product standard EN 61 800-3/A11 for
electrical power drive systems is valid since 01.01.2002.
The following comments apply to the SINAMICS G110
frequency inverters from Siemens:
• The EMC product standard EN 61 800-3/A11 does not
apply directly to a frequency inverter but to a PDS (Power
Drive System) which comprises the complete circuitry,
motor and cables in addition to the inverter.
• A frequency inverter must therefore only be considered as
a component which, on its own, is not subject to the EMC
product standard EN 61 800-3/A11. However, the
inverter’s Instruction Manual specifies the conditions on
how the product standard can be complied with if the
frequency inverter is completed into a PDS. The EMC
directive in the EC is complied with for a PDS by
observance of the product standard EN 61 800-3/A11 for
PDS. The frequency inverters on their own do not
generally require marking according to the EMC directive.
• The frequency inverters as components on their own are
only classified as “restricted availability” for persons and
users with the necessary EMC knowledge. They are not
envisaged for unlimited sale or as “general availability” for
users.
At this point it is necessary to exactly differentiate
between the frequency inverter and the PDS. A PDS can
certainly be envisaged by the machine manufacturer for
general availability, and the standard must be applied
accordingly. On the other hand, the components used in
the PDS may possibly not be for “general availability”.
Page 5/12
• Since 01.01.2002, the EMC product standard
EN 61 800-3/A11 also defines, for the first time, limits for
conducted interference and radiated interference for the
so-called “second environment” (= industrial power supply
systems which do not supply households). Although these
limits lie below those of filter Class A according to
EN 55 011, a PDS with an unfiltered frequency inverter of
SINAMICS G110 series nevertheless does not comply
with these values, and therefore does not meet the
standard EN 61 800-3/A11.
• Using internal or external filters and the installation
instructions included in the documentation, the PDS
designed using the frequency inverters complies with the
product standard EN 61 800-3/A11:
- with low leakage filters of Class B to EN 55 011 in
the first environment (residential, commercial and
light industry), general availability
- with filters of Class A to EN 55 011 in the first
environment plus warning label, restricted sale and
installation by EMC experts
- with filters of Class B to EN 55 011 in the first
environment, restricted sale
- with filters of Class A to EN 55 011 in the second
environment (industrial areas), where these filters
even significantly exceed the requirements of
EN 61 800-3/A11.
• A differentiation must be made between the product
standards for electrical power drive systems (PDS) of the
range of standards EN 61 800-3/ A11 (of which Part 3/
A11 covers EMC topics) and the product standards for the
devices/systems/machines etc. No changes will probably
result in the practical use of frequency inverters. Since
frequency inverters are always part of a PDS, and these
are part of a machine, the machine manufacturer must
observe various standards depending on the type and
environment, e.g. EN 61 000-3-2 for power supply
harmonics and EN 55 011 for radio interferences. The
product standard for PDS on its own is therefore either
insufficient there or irrelevant.
With respect to the compliance of limits for harmonic current
emissions, the EMC product standard EN 61 800-3/A11 for
PDS refers to compliance with the EN 61 000-3-2 and
EN 61 000-3-12 standards.
Electromagnetic compatibility
No inadmissible electromagnetic emissions occur if the
product-specific installation guidelines are correctly
observed.
The table below lists the measured results for emissions
and immunity to interference for inverters SINAMICS G110.
The inverters were installed according to the guidelines with
shielded motor cables and shielded control cables.
SINAMICS G110
EMC phenomenon
Standard/test
Emissions
EN 61 800-3
(1st environment 1))
Conducted via mains cable
Emitted by the drive
Relevant criteria
Limit value
150 kHz to 30 MHz
Unfiltered: not tested
30 MHz to 1 GHz
All devices with internal EMC filter for
power drive systems in category C2
installations (restricted availability 2)).
Limit complies with EN 55 011,
Class A, Group 1.
Furthermore all filtered devices with
shielded cables with a max. length of
5 m comply with the limits of
EN 55 011, Class B.
ESD immunity test
EN 61 000-4-2
ESD through air discharge
ESD through contact discharge
Test level 3
Test level 3
8 kV
6 kV
Electromagnetic fields immunity test
EN 61 000-4-3
Electrical field applied to unit
Test level 3
26 MHz to 1 GHz
10 V/m
Burst immunity test
EN 61 000-4-4
Applied to all cable terminations
Test level 4
4 kV
Surge immunity test
EN 61 000-4-5
Applied to mains cables
Test level 3
2 kV
Immunity to conducted disturbances,
induced by radio frequency fields
EN 61 000-4-6
Applied to mains, motor and control
cables
Test level 4
0.15 MHz to 80 MHz
80 % AM (1 kHz)
10 V
UL listing
UL and cUL listed power conversion equipment type 5B33
in accordance with UL508C.
For use in pollution degree 2 environment.
1) 1st environment
(residential, commercial and light industry): environment which
includes residential areas and, in addition, equipment which is
directly connected to a low-voltage supply without intermediate
transformer, which is used to supply residential buildings.
2) Restricted availability:
Sales channel for which the marketing/sale of the equipment is
limited to distributors, customers or users who - either individually or
together - have technical EMC knowledge.
Category C2:
Power Drive System (PDS) with rated voltage < 1000 V.
When used in 1st environment, installation and start-up only by
EMC experts.
Page 6/12
SINAMICS G110
Selection and ordering data
Rated output
Rated input
current 1)
Rated output
current
kW
hp
A
A
0.12
0.16
2.3
0.9
0.25
0.37
0.55
0.75
1.1
1.5
2.2
3.0
0.33
0.5
0.75
1.0
1.5
2.0
3.0
4.0
4.5
6.2
7.7
10.0
14.7
19.7
27.2
35.6
1.7
2.3
3.2
3.9 (at 40 °C)
6.0
7.8 (at 40 °C)
11.0
13.6 (at 40 °C)
Frame size
FS A
FS A
FS A
FS A
FS A
FS B
FS B
FS C
FS C
The current data applies for an ambient temperature of
50 °C unless otherwise specified.
All SINAMICS G110 inverters are supplied without a Basic
Operator Panel (BOP). Any Basic Operator Panel or other
options have to be ordered separately.
1) The value applies to the rated mains voltage of 230 V.
Page 7/12
Version
Order No.
SINAMICS G110
without filter
SINAMICS G110
with internal filter
Analog
6SL3211-0AB11-2UA0
6SL3211-0AB11-2BA0
USS
6SL3211-0AB11-2UB0
6SL3211-0AB11-2BB0
Analog
(with flat plate)
6SL3211-0KB11-2UA0
6SL3211-0KB11-2BA0
USS
(with flat plate)
6SL3211-0KB11-2UB0
6SL3211-0KB11-2BB0
Analog
6SL3211-0AB12-5UA0
6SL3211-0AB12-5BA0
USS
6SL3211-0AB12-5UB0
6SL3211-0AB12-5BB0
Analog
(with flat plate)
6SL3211-0KB12-5UA0
6SL3211-0KB12-5BA0
USS
(with flat plate)
6SL3211-0KB12-5UB0
6SL3211-0KB12-5BB0
Analog
6SL3211-0AB13-7UA0
6SL3211-0AB13-7BA0
USS
6SL3211-0AB13-7UB0
6SL3211-0AB13-7BB0
Analog
(with flat plate)
6SL3211-0KB13-7UA0
6SL3211-0KB13-7BA0
USS
(with flat plate)
6SL3211-0KB13-7UB0
6SL3211-0KB13-7BB0
Analog
6SL3211-0AB15-5UA0
6SL3211-0AB15-5BA0
USS
6SL3211-0AB15-5UB0
6SL3211-0AB15-5BB0
Analog
(with flat plate)
6SL3211-0KB15-5UA0
6SL3211-0KB15-5BA0
USS
(with flat plate)
6SL3211-0KB15-5UB0
6SL3211-0KB15-5BB0
Analog
6SL3211-0AB17-5UA0
6SL3211-0AB17-5BA0
USS
6SL3211-0AB17-5UB0
6SL3211-0AB17-5BB0
Analog
(with flat plate)
6SL3211-0KB17-5UA0
6SL3211-0KB17-5BA0
USS
(with flat plate)
6SL3211-0KB17-5UB0
6SL3211-0KB17-5BB0
Analog
6SL3211-0AB21-1UA0
6SL3211-0AB21-1AA0
USS
6SL3211-0AB21-1UB0
6SL3211-0AB21-1AB0
Analog
6SL3211-0AB21-5UA0
6SL3211-0AB21-5AA0
USS
6SL3211-0AB21-5UB0
6SL3211-0AB21-5AB0
Analog
6SL3211-0AB22-2UA0
6SL3211-0AB22-2AA0
USS
6SL3211-0AB22-2UB0
6SL3211-0AB22-2AB0
Analog
6SL3211-0AB23-0UA0
6SL3211-0AB23-0AA0
USS
6SL3211-0AB23-0UB0
6SL3211-0AB23-0AB0
SINAMICS G110
Dimension drawings
140 (5.51)
131 (5.16)
FS A inverter; 0.12 kW to 0.37 kW
150 (5.91)
140 (5.51)
150 (5.91)
79 (3.11)
G_D011_EN_00028
116 (4.57)
G_D011_EN_00029
90 (3.54)
90 (3.54)
79 (3.11)
FS A inverter; 0.55 kW to 0.75 kW
101 (4.01)
140 (5.51)
150 (5.91)
79 (3.11)
G_D011_EN_00030
90 (3.54)
FS A inverter with flat plate; 0.12 kW to 0.75 kW
152 (5.98)
140 (5.51)
170 (6.70)
181 (7.13)
135 (5.31)
160 (6.30)
G_D011_EN_00031
142 (5.59)
127 (5.0)
G_D011_EN_00032
184 (7.24)
140 (5.51)
FS B inverter; 1.1 kW to 1.5 kW
FS C inverter; 2.2 kW to 3.0 kW
With plugged Basic Operator Panel (BOP), the mounting
depth increases by 8 mm (0.31 inches).
All dimensions are in mm (values in brackets are in inches).
Page 8/12
SINAMICS G110
Circuit diagrams
General circuit diagram
Basic Operator Panel (option)
200 V to 240 V 1 AC
PE
FS1
PE
A n a lo g v a r ia n t
+10 V 8
Input voltage
0 V to + 10 V
AIN+
+
-
9
A
AIN+ 9
> 4.7 k
-
or
0V
L1, L2/N
10
D
0 V 10
U S S v a r ia n t
P+
8
A
9
B
AC
RS485
N-
DC
DC+
CPU
50 OFF
Hz
max. 30 V
max. 5 mA
DIN0
3
DIN0
3
DIN1
4
DIN1
4
DIN2
5
DIN2
5
or
DC -
60 Bus
Hz Termination
DC
AC
6
7
7
DOUT+
24 V DC 50 mA
DOUT-
+24 V (max. 50 mA)
0V
2
1
PE
U, V, W
M
3~
For an additional digital input (DIN 3)
external connections should be made:
DIN3
+
24 V
-
or
0V
Page 9/12
DIN3 9
9
7
24 V 6
G_D011_EN_00027
+
24 V
-
SINAMICS G110
Variant dependent options
Class B filter with low leakage currents
Overview
With this filter, the unfiltered inverter complies with the
emission standard EN 55 011, Class B. The leakage
currents are reduced to < 3.5 mA.
Internal EMC filter
Variants with internal EMC filter for both Class A and
Class B environments are available.
• Class A
For Class A the requirements are fulfilled using shielded
cables with a max. length of 10 m for FS A or 25 m for
FS B and FS C. The limits comply with EN 55 011
Class A.
• Class B
For Class B the requirements are fulfilled using shielded
cables with a maximum length of 5 m. The limit complies
with EN 55 011 Class B.
An inverter with an internal filter can be used with a 30 mA
residual-current circuit-breaker, and is only suitable for
hardwired installations.
A non-filtered inverter together with the optional filter “Filter
Class B with low leakage currents” has a leakage current
< 3.5 mA (shielded motor cable up to 5 m).
Additional EMC filter Class B
Obtainable for inverters with an internal EMC filter Class A.
With this filter, the inverter complies with the emission
standard EN 55 011, Class B.
The requirements are fulfilled using shielded cables with a
max. length of 25 m.
Unfiltered inverters with frame sizes A and B can be used
for power drive systems in category C1 installations (general
availability).
The requirements are fulfilled
• using shielded cables with a max. length of 5 m and
• installing the inverter in a metallic enclosure (e.g. control
panel).
Line reactor
Line reactors are used to smooth voltage peaks or to bridge
commutating dips.
In addition, line reactors reduce the effects of harmonics on
the inverter and the power supply.
If the ratio of inverter rated power to network short-circuit
power is less than 1 %, a line reactor must be used in order
to reduce the current peaks.
In line with the EN 61 000-3-2 regulations “Limits for
harmonic currents with device input current ≤ 16 A per
phase”, there are special aspects for drives with 250 W to
550 W and 230-V single-phase supplies which can be used
in non-industrial applications (1st environment).
For devices with 250 W and 370 W it is necessary either to
fit the recommended line reactors or to apply to the power
utility company for authorization to connect the devices to
the public power supply.
No limits are currently defined in the EN 61 000-3-2
standard for professionally used devices with a connected
load > 1 kW. This means that the inverters with an output
power ≥ 0.75 kW comply with the EN 61 000-3-2 standard.
Page 10/12
SINAMICS G110
Selection and ordering data
The options listed here (EMC filters, line reactors, fuses and
circuit-breakers) are inverter specific.
EMC filters and line reactors have to be mounted separately
as there are no footprint versions.
All variant dependent options and the Basic Operator
Panel BOP are certified to UL except fuses. The fuses of
type 3NA3 are recommended for Europe.
Use in America requires UL listed fuses, for example the
Class NON range from Bussmann.
The inverter and the associated options have the same
voltage ratings.
Rated output
Order No. of the options
kW
Filter Class B with low
leakage current
Line reactor
Supplementary Class B
EMC filter
Fuse
Circuit-breaker
Options for inverters without filter
0.12
6SE6400-2FL01-0AB0
6SE6400-3CC00-4AB0
-
3NA3803
3RV1021-1DA10
0.25
6SE6400-2FL01-0AB0
6SE6400-3CC00-4AB0
-
3NA3803
3RV1021-1FA10
0.37
6SE6400-2FL01-0AB0
6SE6400-3CC01-0AB0
-
3NA3803
3RV1021-1HA10
0.55
6SE6400-2FL01-0AB0
6SE6400-3CC01-0AB0
-
3NA3803
3RV1021-1JA10
0.75
6SE6400-2FL01-0AB0
6SE6400-3CC01-0AB0
-
3NA3805
3RV1021-1KA10
1.1
6SE6400-2FL02-6BB0
6SE6400-3CC02-6BB0
-
3NA3807
3RV1021-4BA10
1.5
6SE6400-2FL02-6BB0
6SE6400-3CC02-6BB0
-
3NA3810
3RV1021-4CA10
2.2
6SE6400-2FL02-6BB0
6SE6400-3CC02-6BB0
-
3NA3814
3RV1031-4EA10
3.0
-
6SE6400-3CC03-5CB0
-
3NA3820
3RV1031-4FA10
Options for inverters with internal filter Class A/B
0.12
-
6SE6400-3CC00-4AB0
6SE6400-2FS01-0AB0
3NA3803
3RV1021-1DA10
0.25
-
6SE6400-3CC00-4AB0
6SE6400-2FS01-0AB0
3NA3803
3RV1021-1FA10
0.37
-
6SE6400-3CC01-0AB0
6SE6400-2FS01-0AB0
3NA3803
3RV1021-1HA10
0.55
-
6SE6400-3CC01-0AB0
6SE6400-2FS01-0AB0
3NA3803
3RV1021-1JA10
0.75
-
6SE6400-3CC01-0AB0
6SE6400-2FS01-0AB0
3NA3805
3RV1021-1KA10
1.1
-
6SE6400-3CC02-6BB0
6SE6400-2FS02-6BB0
3NA3807
3RV1021-4BA10
1.5
-
6SE6400-3CC02-6BB0
6SE6400-2FS02-6BB0
3NA3810
3RV1021-4CA10
2.2
-
6SE6400-3CC02-6BB0
6SE6400-2FS02-6BB0
3NA3814
3RV1031-4EA10
3.0
-
6SE6400-3CC03-5CB0
6SE6400-2FS03-5CB0
3NA3820
3RV1031-4FA10
Page 11/12
SINAMICS G110
Variant independent options
Connection set for PC to inverter
Overview
For controlling and commissioning an inverter directly from a
PC if the appropriate software has been installed
(STARTER).
Basic Operator Panel (BOP)
With the BOP, individual parameter settings can be made.
Values and units are shown on a 5-digit display.
A BOP can be used for several inverters. It is directly
plugged into the inverter.
The BOP offers a parameter cloning function which allows
one parameter set to be stored from an inverter and then
downloaded into another inverter.
Isolated RS232 adapter board for reliable point to point
connection for a PC.
It offers a 9-pin Sub-D connector and an RS232 standard
cable (3 m).
Commissioning tool
STARTER is a graphic start-up software for guided
commissioning for SINAMICS G110 frequency inverters
under Windows NT/2000. Parameter lists can be read out,
altered, stored, entered and printed.
Selection and ordering data
The options listed here are suitable for all SINAMICS G110
inverters.
Options
Order No.
Basic Operator Panel (BOP)
6SL3255-0AA00-4BA0
Connection kit for PC to inverter
6SL3255-0AA00-2AA0
Adapter for mounting on DIN rail, Size 1 (FS A)
6SL3261-1BA00-0AA0
Commissioning tool STARTER on CD-ROM,
including: operating instructions, parameter list, getting started guide 1)
6SL3271-0CA00-0AG0
1) Documentation is also available on the Internet at
http://www.siemens.com/sinamics-g110
Documentation
Selection and ordering data
Type of documentation
Language
1
Operating instructions ) (paper version)
1
Parameter list ) (paper version)
1
Getting Started Guide )
German
6SL3298-0AA11-0AP0
English
6SL3298-0AA11-0BP0
French
6SL3298-0AA11-0DP0
Italian
6SL3298-0AA11-0CP0
Spanish
6SL3298-0AA11-0EP0
German
6SL3298-0BA11-0AP0
English
6SL3298-0BA11-0BP0
French
6SL3298-0BA11-0DP0
Italian
6SL3298-0BA11-0CP0
Spanish
6SL3298-0BA11-0EP0
Multilanguage
A paper version is supplied with each inverter.
1) Documentation is also available on the Internet at
http://www.siemens.com/sinamics-g110
Page 12/12
Order No.
Download PDF