UFH-70DDA Operation manual [PDF:346.9KB]

UFH-70DDA Operation manual [PDF:346.9KB]
OPERATION
MANUAL
UFH-70DDA
Digital Distribution Amplifier
1st Edition
Precautions
Important Safety Warnings
[Power]
Stop
Do not place or drop heavy or sharp-edged objects on power cord. A damaged cord
can cause fire or electrical shock hazards. Regularly check power cord for
excessive wear or damage to avoid possible fire / electrical hazards.
[Circuitry Access]
Stop
Do not touch any parts / circuitry with a high heat factor.
Capacitors can retain enough electric charge to cause mild to serious shock, even
after power is disconnected. Capacitors associated with the power supply are
especially hazardous. Avoid contact with any capacitors.
Hazard
Unit should not be operated or stored with cover, panels, and / or casing removed.
Operating unit with circuitry exposed could result in electric shock / fire hazards or
unit malfunction.
[Potential Hazards]
Caution
If abnormal smells or noises are noticed coming from the unit, turn power off
immediately and disconnect power cord to avoid potentially hazardous conditions. If
problems similar to above occur, contact authorized service representative before
attempting to again operate unit.
[Consumables]
Caution
The consumables used in unit must be replaced periodically. For further details on
which parts are consumables and when they should be replaced, refer to the
specifications at the end of the Operation Manual. Since the service life of the
consumables varies greatly depending on the environment in which they are used,
they should be replaced at an early date. For details on replacing the consumables,
contact your dealer.
Upon Receipt
Unpacking
UFH-70DDA units and their accessories are fully inspected and adjusted prior to shipment.
Operation can be performed immediately upon completing all required connections and
operational settings.
Check your received items against the packing lists below.
ITEM
UFH-70DDA
Operation Manual
QTY
1
1
REMARKS
(This manual)
Check
Check to ensure no damage has occurred during shipment. If damage has occurred, or items
are missing, inform your supplier immediately.
Table of Contents
1. Prior to Starting ...........................................................................................................................1
1-1. Welcome .............................................................................................................................1
1-2. Features..............................................................................................................................1
1-3. About This Manual ..............................................................................................................1
2. Panel Descriptions ......................................................................................................................2
2-1. Front Panel .........................................................................................................................2
2-2. Rear Panel..........................................................................................................................2
2-3. Mode Setting.......................................................................................................................3
3. Connection..................................................................................................................................4
3-1. Connection Example...........................................................................................................4
4. Operation ....................................................................................................................................5
4-1. Power ON ...........................................................................................................................5
5. Specifications and Dimensions ...................................................................................................6
5-1. Unit Specifications...............................................................................................................6
5-2. External Dimensions ...........................................................................................................7
1. Prior to Starting
1-1. Welcome
Congratulations! By purchasing UFH-70DDA Digital Distribution Amplifier you have entered the
world of FOR-A and its many innovative products. Thank you for your patronage and we hope
you will turn to FOR-A products again and again to satisfy your video and audio needs.
FOR-A provides a wide range of products, from basic support units to complex system
controllers, which have been increasingly joined by products for computer video based systems.
Whatever your needs, talk to your FOR-A representative. We will do our best to be of continuing
service to you.
1-2. Features
The UFH-70DDA System Frame module is a signal distribution amplifier for FOR-A System
Frames with 1-input/7-output distribution of serial digital component signals in both SD and HD.
Installable to FOR-A System Frames (UFH-108/108A or UFH-112/112A)
Accepts and distributes digital component signals in both SD and HD. (Auto switching)
Cable compensation function allows the input-side cable length to be as long as 200 meters
when BNC 5C-2V, RG-11A/U or equivalent cable used for SD SDI, and 100 meters when
BNC 5C-FB, RG-59B/U or equivalent cable used for HD SDI.
Reclock function to minimize signal jitters.
HD and SD Input Signal Auto Detection / Auto Switching
Supports DVB-ASI signals by changing internal setting.
1-3. About This Manual
This manual is intended to help the user easily operate this product and make full use of its
functions during operations. Before connecting or operating your unit, read this operation
manual thoroughly to ensure you understand the product. After reading, it is important to keep
this manual in a safe place and available for reference.
1
2. Panel Descriptions
2-1. Front Panel
(5)
POWER
INPUT
A
HD
DVB-ASI
INPUT
B (OPTION)
HD
(OPTION)
INTERFACE
DVB-ASI
UFH-70DDA
UFH-70DDA
(1)
(1)
POWER Indicator
(2)
(3)
(4)
(5)
(6)
(2) (3)
INPUT
A
HD
DVB-ASI
B (OPTION)
INTERFACE
(4)
(6)
Power indicator lights green whenever power is applied to the
unit.
Indicator lights whenever an HD or SD serial digital signal is
inputted to the unit.
Indicator lights whenever an HD serial digital signal is inputted to
the unit.
Indicator lights whenever the system operates in DVB-ASI mode.
Not used.
Not used.
2-2. Rear Panel
HD/SD
HD/SD 1
HD/SD 2
HD/SD 3
VIDEO IN
VIDEO OUT
(1)
(1)
VIDEO IN
(2)
VIDEO OUT
HD/SD 4
HD/SD 5
HD/SD 6
HD/SD 7
UFH-70DDA
(2)
Used for serial digital component video (HD/SD SDI) input
connection.
Used for serial digital component video (HD/SD SDI) output
connection. The unit distributes the input signal to seven
identical outputs.
2
2-3. Mode Setting
The unit has two operation modes: SD/HD SDI mode and DVB-ASI mode. The SD/HD SDI
mode is set at the factory shipping. To switch the operation mode of the unit, change the mode
switch on the rear module board as shown in the figure below.
UFH-70DDA rear module
VIDEO
Switch Setting
VIDEO side
DVB side
Operation Mode
SD/HD SDI (default)
DVB-ASI
DVB
The mode setting must be done before installing the rear module to the System Frame and
inputting DVB-ASI signal. The DVB-ASI indicator on the front panel will glow when switching to
DVB-ASI mode.
3
3. Connection
Note that before installing UFH-70DDA into the System Frame you should thoroughly read the
operation manual for the System Frame you will be installing to.
IMPORTANT
When installing module boards, keep boards in their insulated packet until just prior to
installation to avoid static electricity problems. Also, do not touch board components
for the same reason.
3-1. Connection Example
Connect the unit to other equipment in the total system as shown in the figure below.
UFH-112A
HD SDI signal
or
SD SDI signal
HD/SD SDI
IN
HD/SD
OUT 1
HD/SD
OUT 2
HD/SD
OUT 3
UFH-70DDA
HD/SD
OUT 4
HD/SD
OUT 5
HD/SD
OUT 6
HD/SD
OUT 7
4
HD SDI signal
or
SD SDI signal
4. Operation
4-1. Power ON
1) Loosen the two knob screws on the front panel face of the System Frame, and then grasp the
knob screws to pull them out.
POWER
1
GENLOCK
1
2
FAN
ALARM
TEMP DC POW
UFH-112
SYSTEM FRAME
POWER
2
GENLOCK
1
2
FAN
ALARM
TEMP DC POW
2) Turn the power switch(es) ON.
5
5. Specifications and Dimensions
5-1. Unit Specifications
Video Input
HD SDI 1.485/1.001Gbps,
SD SDI 143Mbps - 270Mbps, or
DVB-ASI 270Mbps,
75Ω BNC 1 input
Video Output
HD SDI 1.485/1.001Gbps,
SD SDI 143Mbps to 270Mbps, or
DVB-ASI 270Mbps,
75Ω BNC 7 outputs
Cable Length
Compensation
0m to 100m when 5C-FB, RG-59B/U or equivalent cable used for HD SDI.
0m to 200m when 5C-2V, RG-11A/U or equivqlent cable used for SD SDI.
Temperature
10°C - 40°C
Humidity
30% - 90% (no condensation)
Power
+ 24VDC (supplied from System Frame)
Power
Consumption
4.6VA (4.6W)
Dimensions
Front module:138.5 (W) x 400 (D) mm
Rear module:141 (W) x 101 (D) mm
Weight
1.0 kg
Required Slot
1 slot
6
5-2. External Dimensions
(All dimensions in mm.)
141
VIDEO IN
U FH -7 0D D A
VIDEO OUT
20
HD/S D
87.8
(101)
379.5
(400)
HD/S D 1
HD/SD 2
HD/SD 3
HD/S D 4
HD/SD 5
HD/SD 6
HD/SD 7
EXTENTION CARD(Option)
I/F CARD (Option)
POWER
A
IN PU T
HD
B (OPTION)
DV B-ASI
INPU T
HD
DV B-ASI
( OP TION)
IN TE RFAC E
UFH- 70DD A
UF H-70 DDA
7
Warning
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in
which case the user will be required to correct the interference at his own
expense.
09/29/2009 Printed in Japan
FOR-A COMPANY LIMITED
Head Office
Overseas Division
Japan Branch Offices
R&D/Production
: 3-8-1 Ebisu, Shibuya-ku, Tokyo 150-0013, Japan
Phone: +81 (0)3-3446-3936, Fax: +81 (0)3-3446-1470
: Osaka/Okinawa/Fukuoka/Hiroshima/Nagoya/Sendai/Sapporo
: Sakura Center/Sapporo Center
FOR-A America Corporate Office
11125 Knott Ave., Suite #A, Cypress, CA 90630, USA
Phone: +1 714-894-3311 Fax: +1 714-894-5399
FOR-A America East Coast Office
Two Executive Drive, Suite 670, Fort Lee Executive Park, Fort Lee NJ 07024, USA
Phone: +1 (201) 944-1120 Fax : +1 (201) 944-1132
FOR-A America Distribution & Service Center
2400 N.E. Waldo Road, Gainesville, FL 32609, USA
Phone: +1 352-371-1505 Fax: +1 352-378-5320
FOR-A Corporation of Canada
346A Queen Street West, Toronto, Ontario M5V 2A2, Canada
Phone: +1 416-977-0343 Fax: +1 416-977-0657
FOR-A Latin America & the Caribbean
5200 Blue lagoon Drive,
Suite 760, Miami, FL 33126, USA
Phone: +1-305-931-1700 Fax: +1-305-264-7890
FOR-A UK Limited
UNIT C71, Barwell Business Park, Leatherhead Road, Chessington Surrey, KT9 2NY, UK
Phone: +44 (0)20-8391-7979 Fax: +44 (0)20-8391-7978
FOR-A Italia S.r.l.
Viale Europa 50 20093, Cologno Monzese (MI), Milan, Italy
Phone: +39 02-254-3635/6 Fax: +39 02-254-0477
FOR-A Corporation of Korea
801 Dangsan Bld., 53-1 Dangsan-Dong, Youngdeungpo-Gu, Seoul 150-800, Korea
Phone: +82 (0)2-2637-0761 Fax: +82 (0)2-2637-0760
FOR-A China Limited
708B Huateng Building, No. 302, 3 District, Jinsong, Chaoyang, Beijing 100021, China
Phone: +86 (0)10-8721-6023 Fax: +86 (0)10-8721-6033
*The contents of this manual are subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement