Bose | Soundlink AM323699 | Technical information | Bose Soundlink AM323699 Technical information

Bose SoundLink
­Bluetooth speaker III
®
®
®
Owner’s Guide
Safety
Please read this guide
Please take the time to follow the instructions in this owner’s guide carefully. It will help you set up and operate your
system properly and enjoy its advanced features. Please save this guide for future reference.
The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the presence of
uninsulated, dangerous voltage within the system enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral triangle, as marked on the system, is intended to alert the user
to the presence of important operating and maintenance instructions in this owner’s guide.
WARNINGS:
•To reduce the risk of fire or electrical shock, do not expose the product to rain or moisture.
•Do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such
as vases, on or near the apparatus. As with any electronic products, use care not to spill liquids into any
part of the system. Liquids can cause a failure and/or a fire hazard.
•Do not place any naked flame sources, such as lighted candles, on or near the apparatus.
•Do not use any charger other than that specifically provided for use with the equipment.
•The battery needs to be charged before use. Always use the correct charger and refer to the
­manufacturer’s instructions or equipment manual for proper charging instructions.
•After extended periods of storage, it may be necessary to charge and discharge the battery pack several
times to obtain maximum performance.
•The battery pack gives its best performance when it is operated at normal room temperature
(68°F +/- 23°F or 20°C +/- 5°C).
•Do not leave a battery on prolonged charge when not in use.
•The battery pack shall not be exposed to excessive heat such as sunshine, fire or the like.
•Do not subject battery pack to mechanical shock.
•In the event of fluid from the battery leaks from the equipment, do not allow the liquid to come in contact
with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water
and seek medical advice.
•Do not use any battery pack which is not designed for use with the equipment.
•Keep battery pack clean and dry.
•For battery replacement, please contact Bose Customer Service.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Bose
Corporation is under license.
Wi-Fi is a registered mark of the Wi-Fi Alliance.
©2013 Bose Corporation. No part of this work may be reproduced, modified, distributed, or otherwise used without prior written permission.
2 - English
Safety
WARNING: This product contains magnetic material. Please contact your physician if you have any
questions on whether this might affect the operation of your implantable medical device.
CAUTION: Make no modifications to the system or accessories. ­Unauthorized alterations may
compromise safety, ­regulatory compliance, and system performance.
NOTES:
•The product label is located on the bottom of the product.
•Where the mains plug or appliance coupler is used as the disconnect device, such disconnect device shall remain
readily operable.
•The AC power supply provided with this product must be used indoors. It is neither designed nor tested for use
outdoors, in recreation vehicles, or on boats.
•This product is intended to be used only with the AC power supply provided, or a Bose® AC power supply or
charger designed for use with this product.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9.Only use attachments/accessories specified by the ­manufacturer.
10.Unplug this apparatus during lightning storms or when unused for long periods of time.
11.Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
Information about products that ­generate electrical noise
This device complies with FCC and Industry Canada RF radiation exposure limits set forth for general population.
It must not be co-located or operating in conjunction with any other antennas or transmitters.
This device complies with Part 15 of the FCC Rules. ­Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
English - 3
Safety
U.S.A. only
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Bose ­Corporation could void the user’s authority to operate
this ­equipment.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) This device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Output power: 7 mW @ 2400-2483.5 MHz
Bose Corporation hereby declares that this product is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC and to all applicable EU directive requirements.
The complete declaration of conformity can be found at www.Bose.com/compliance
Names and Contents of Toxic or Hazardous Substances or Elements
Toxic or Hazardous Substances and Elements
Lead
Mercury
Cadmium
Hexavalent
Polybrominated
Polybrominated Diphenyl
(Hg)
(Cd)
(CR(VI))
Biphenyl (PBB)
Ether (PBDE)
Part Name (Pb)
PCBs
X
0
0
0
0
0
Metal
X
0
0
0
0
0
parts
Plastic
0
0
0
0
0
0
parts
Speakers
X
0
0
0
0
0
Cables
X
0
0
0
0
0
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is
below the limit requirement in SJ/T 11363-2006.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used
for this part is above the limit requirement in SJ/T 11363-2006.
Please complete and retain for your records.
The serial and model number can be found on the bottom of the speaker.
Serial number: ____________________________________________________________________
Model number: ___________________________________________________________________
Purchase date: ___________________________________________________________________
We suggest you keep your receipt with this owner’s guide.
4 - English
Contents
Introduction
Overview...............................................................................................................6
Unpacking............................................................................................................6
Operation
Connecting to AC power....................................................................................7
Pairing and connecting a device to the speaker...........................................9
First-time setup...........................................................................................9
Adding another device to the speaker....................................................10
Speaker memory.........................................................................................10
Reconnecting a device...............................................................................10
Switching to a different device.................................................................10
Control buttons...................................................................................................11
System status indicators..................................................................................12
Connecting a device using the AUX connector.............................................13
Operating on battery power.............................................................................14
Checking the battery..................................................................................14
Charging the battery..................................................................................14
Battery protection mode...........................................................................14
Tips on placing the speaker..............................................................................15
Maintenance and Care
Troubleshooting.................................................................................................16
Replacing the battery........................................................................................18
Cleaning the speaker.........................................................................................18
Contacting customer service...........................................................................18
Technical information.......................................................................................18
English - 5
Introduction
Overview
Thank you for purchasing the Bose® SoundLink® Bluetooth® speaker III. Enjoy
music wirelessly from your smartphone, tablet, laptop, or other Bluetooth device
anywhere you choose.
Features
• Wireless Bluetooth link eliminates the need to physically connect your
Bluetooth device.
• Rechargeable lithium-ion battery provides hours of Bose performance.
• AUX connector lets you connect any music device directly to your speaker.
• Pair up to six Bluetooth devices.
• Easy grab-and-go mobility.
Unpacking
Open the carton and remove the speaker and AC power supply. Depending on
your region, the carton may also contain AC power adapters for the AC power
­supply. Be sure to save all of the packing materials. These provide the safest
means for any ­necessary shipping or transporting of the system.
If any part of the product appears to be ­damaged, do not attempt to use it.
Contact your authorized Bose dealer immediately or call Bose Customer Service.
For ­contact information, refer to the contact list at the end of this guide or visit
http://global.Bose.com.
SoundLink® Bluetooth® speaker III
6 - English
AC power supply
AC power supply
adapters
Operation
Connecting to AC power
The first time using your SoundLink® Bluetooth® speaker III, connect it to AC
(mains) power and charge the battery for three hours. While the battery is charging,
you can begin using the speaker.
1. Depending on your AC power supply type:
a. Extend the prongs from the AC power supply.
Or,
b. Slide the AC power adapter for your region onto the AC power supply.
English - 7
Operation
2. Plug the power cord on the AC power supply into the DC connector on the
back of the speaker.
3. Plug the AC power supply into a live AC (mains) outlet.
The speaker emits a tone to confirm connection to AC power, and ­charging
begins. On the front of the speaker, the battery status indicator
­blinks
­yellow to show the battery is charging.
8 - English
Operation
Pairing and connecting a device to the speaker
Before listening to music from your Bose® Soundlink® Bluetooth® speaker III, you
must pair and connect your Bluetooth device to the speaker.
First-time setup
The first time you turn on your speaker, it is ready to pair and connect your
first device.
1. Press Power
to turn the speaker on.
The ­Bluetooth status indicator
speaker is discoverable.
on the speaker blinks blue to show the
2. On your device, turn Bluetooth on, locate the Bluetooth device list, and select
the ­device named “Bose SLIII.” If your device prompts you for a passcode,
enter “0000” (four zeros).
Settings
Bluetooth
Bluetooth
ON
Devices
Bose SLIII
Connected
When pairing is complete and your device is connected to the speaker, the
­Bluetooth status indicator on the speaker changes from blinking blue to
solid white and the speaker emits a tone.
Note: If the speaker turns off after five minutes, it has not paired or connected with
your device. Turn the speaker off and back on, and try pairing your device
again. See “Troubleshooting” on page 16.
English - 9
Operation
Adding another device to the speaker
Pair another device to the speaker by making the speaker discoverable.
1. Press Bluetooth®
blinks blue.
on the speaker, so the Bluetooth status indicator
2. On your device, turn Bluetooth on, locate the Bluetooth device list, and select
the ­device named “Bose SLIII.” If your device prompts you for a passcode,
enter “0000” (four zeros).
When the device connects to the speaker, the ­Bluetooth status indicator turns
to solid white.
Note: You can switch between connecting/connected and discoverable by
­pressing ­Bluetooth on the speaker.
Speaker memory
The speaker can remember up to six paired devices. If you pair the speaker with
an additional device, the device least recently connected is no longer paired with
the speaker.
Note: To clear the speaker memory of all devices, press and hold Bluetooth
(about 10 seconds) until you hear a tone. All devices are cleared and the
speaker becomes discoverable.
Reconnecting a device
When turned on, the speaker attempts to reconnect with a device in memory
­starting with the last connected device. If the last connected device is not
­available, the speaker connects to the next to last connected device, and so forth.
The speaker searches for a paired device for approximately 30 seconds.
Switching to a different device
You can switch the speaker from your connected device to another previously
paired ­device. The device you are switching to must be in the speaker memory.
1. On your previously paired device, make sure Bluetooth is turned on.
2. Press Bluetooth
on the speaker to make the speaker discoverable.
The Bluetooth status indicator
is discoverable.
speaker blinks blue to show the speaker
3. On your device, select “Bose SLIII” from the Bluetooth device list.
The Bluetooth status indicator blinks white, while the speaker attempts to connect to the device.
When the speaker and Bluetooth device have ­successfully connected, the
­ luetooth status indicator changes from blinking to solid white and the
B
speaker emits a tone.
10 - English
Operation
Control buttons
Control buttons are located on the top of the speaker.
Control
button
Description
Press to turn the speaker on or off.
• When Bluetooth® is the selected source, the speaker attempts to
­reconnect to the last connected device. If there are no paired devices,
the speaker becomes ­discoverable. See “Pairing and connecting a device
to the speaker” on page 9.
• If operating on battery power, press and hold to observe the battery
status indicator. See “Checking the battery” on page 14.
• If the speaker is not used within 30 ­minutes, the speaker automatically
turns off to preserve battery power.
Press to select the Bluetooth source.
• The speaker attempts to connect to the last paired device. If there are no
paired devices, the speaker becomes discoverable.
• If Bluetooth is connecting/connected, press to set the speaker to
­discoverable to allow pairing with another Bluetooth device. Press again to
go back to ­connecting mode.
Press to listen to a device plugged into the AUX connector. See “Connecting
a device using the AUX connector” on page 13.
Press to mute/unmute sound from the speaker.
Press to decrease the speaker volume incrementally. Press and hold to
­decrease the volume continuously.
Press to increase the speaker volume incrementally. Press and hold to
­increase the volume continuously.
English - 11
Operation
System status indicators
Status indicators illuminate to show when an audio source or speaker state is
­activated. Status indicators are located on the front of the speaker.
Status
indicator
System status
Indicates the Bluetooth® state of the speaker when the Bluetooth source
is ­selected. See “Pairing and connecting a device to the speaker” on
page 9.
•
•
•
•
Blinking blue light – Discoverable and ready to pair with a device.
Blinking white light – Attempting to connect to a paired device.
Solid white light – Connected to a paired device.
Blinks as the volume of the speaker increases or decreases when
­Bluetooth is the source. When the indicator blinks twice, the maximum or
minimum volume has been reached.
• The speaker is playing the source connected to the AUX IN
connector.
• Blinks as the volume of the speaker increases or decreases when AUX is
the source. When the indicator blinks twice, the maximum or minimum
volume has been reached.
Blinks when the sound is muted.
Indicates the battery power level or the battery charging state. See “Checking
the battery” on page 14.
12 - English
Operation
Connecting a device using the AUX connector
You can use your speaker with any device that ­features a headphone or audio
­output. This feature requires using a stereo audio cable with a 3.5 mm plug on
one end to­connect to the AUX IN input
on the speaker. This type of cable is
­available for ­purchase at electronics stores.
To use the AUX IN connector:
1. Plug the cable from your audio device into the AUX IN connector
back of the speaker.
2. Press Power
on the
on the speaker.
3. Press AUX on the speaker.
4. Adjust the volume on the connected device to near maximum, then use
the speaker volume buttons to adjust the volume level.
Notes:
• If the connected device stops playing audio for 30 minutes, the speaker
­automatically turns off to conserve battery power.
• The SERVICE connector on the back of the speaker is only for software updates.
It cannot be used to connect an audio device.
English - 13
Operation
Operating on battery power
Battery performance varies with the content played and the loudness at which
it is played. In typical usage, the speaker battery lasts up to 14 hours.
Checking the battery
When the speaker is turned on, the battery status indicator briefly illuminates, then
turns off to conserve battery power. However, if the battery requires charging, the
battery status indicator illuminates and continuously blink red until the speaker the
speaker is connected to AC power and the battery begins charging.
To check the battery charge level, press and hold Power
observe the battery status indicator.
Solid green
Full charge
Solid yellow
Medium charge
Blinking red
Charging is needed
on the speaker and
Charging the battery
The battery status indicator on the ­speaker blinks red when the battery needs
charging.
To charge the battery, connect the speaker to AC power (see “Connecting to AC
power” on page 7). The speaker emits a tone to confirm the power connection.
Recommended charging time is three hours to fully charge the battery. The b
­ attery
status indicator indicates the charging status. You can use the speaker while
charging the battery.
Blinking yellow
Battery is charging
Solid green
Battery is fully charged
Battery protection mode
When the speaker is unplugged and unused for more than 24 days, it enters
­battery protection mode to preserve battery power. To reactivate the speaker,
­connect it to AC power (see “Connecting to AC power” on page 7).
14 - English
Operation
Tips on placing the speaker
When using your speaker indoors, the tonal quality can vary depending on where
the speaker is placed in a room.
When using your speaker outdoors, you should ­expect the tonal quality to change
as you move farther away from the speaker.
Follow these guidelines when placing your speaker:
• The speaker is designed to sound best when placed on a surface that is 24 to 48
inches high.
• For best bass response, the back of the speaker should be placed near a wall,
but not directly against a wall. Bass response decreases as the speaker is
moved away from a wall. Do not lay the speaker on its back. Sound is emitted
from both the front and the rear of the speaker.
• Do not place the speaker in small areas where the speaker is enclosed on all
sides except the front, as this will adversely affect sound quality.
• Do not place the speaker on wet or dirty surfaces.
English - 15
Maintenance and Care
Troubleshooting
Problem
What to do
Speaker will
not turn on
If using AC power, ensure:
•Your system is connected to a working AC (mains) outlet.
•You are using the Bose® AC power supply shipped with your speaker or a Bose
accessory charger designed for the speaker.
If using battery power, the battery may be in protection mode or discharged. Connect
to a working AC outlet to restore the battery to ­operational mode and charge the
battery.
Cannot pair
the speaker
with my
­Bluetooth®
device
•Ensure your speaker is discoverable (Bluetooth status indicator blinks blue).
See “Pairing and connecting a device to the speaker” on page 9.
•Ensure Bluetooth is enabled on your device.
•Ensure you have selected “Bose SLIII” in the Bluetooth device list on your device
and the connection has been confirmed by your device.
•Your Bluetooth device may be out of range. Try moving it closer to the speaker.
•If possible, turn off all other nearby Bluetooth devices or disable their Bluetooth
functionality.
•Ensure your device supports the A2DP (stereo Bluetooth) profile.
•When pairing and connecting to a PC or Mac computer, ensure you have selected
the SoundLink® Bluetooth® speaker III as the audio output device within the audio
settings menu of the computer. You may need to play an audio track to finalize the
connection (see the computer manufacturer for detailed instructions).
•Refer to the owner’s guide, help system, or technical support for your Bluetooth
device to learn how it pairs with other Bluetooth devices.
•Turn the speaker off and back on, and pair and connect your device.
See “First-time setup” on page 9 and “Adding another device” on page <?>.
•Reset the speaker. Press and hold Mute on the speaker for ten ­seconds until all
status ­indicators briefly illuminate and the speaker turns off. Turn the speaker on
again, and pair your device.
•Check for updated software for your Bluetooth device, or go to owners.Bose.com
for updates to the SoundLink® Bluetooth® speaker III.
Paired
•Ensure your speaker is discoverable (Bluetooth status indicator blinks blue).
­ luetooth
B
See “Pairing and connecting a device to the speaker” on page 9.
­device will not •Ensure Bluetooth is enabled on your device.
­connect to
•Your device may be out of range. Try moving it closer to the speaker.
the speaker
•Turn your device off and back on, and connect it to the speaker.
See “Reconnecting a device” on page <OV>.
•If possible, turn off all other nearby Bluetooth devices or disable their Bluetooth
functionality.
•Reset the speaker. Press and hold Mute on the speaker for ten ­seconds until all
status ­indicators briefly illuminate and the speaker turns off. Turn the speaker on
again, and connect your device.
•Clear the speaker memory. Pair and connect the device to the speaker again.
See “Speaker memory” on page 10 and “First-time setup” on page 9.
16 - English
Maintenance and Care
Problem
What to do
The speaker
indicates a
connection,
but is not
playing music
•Ensure the device you want to hear is connected to the speaker and playing audio.
•Ensure the speaker is not muted and the speaker volume is turned up.
•Turn up the volume on your device.
•Your Bluetooth® device may be out of range. Try moving it closer to the speaker.
•Move your device away from any device that generates ­electromagnetic
­interference, such as another Bluetooth device, cordless phone,microwave
oven, or wireless router.
•If possible, turn off all other nearby Bluetooth devices or disable their Bluetooth
functionality and reconnect the device you want to hear.
•Refer to the owner’s guide, help system, or technical support for your Bluetooth
device to learn how it pairs with other Bluetooth devices.
•Turn the speaker off and back on.
•Reset the speaker. Press and hold Mute on the speaker for ten ­seconds until all
status ­indicators briefly illuminate and the speaker turns off. Turn the speaker on
again, and connect your device.
Poor sound
quality from
a Bluetooth
device
Connect your Bluetooth device to the speaker using the AUX connection. If sound
quality improves using the AUX connection, try these solutions:
•Your Bluetooth device may be out of range. Try moving it closer to the speaker.
•Move your device away from any device that generates ­electromagnetic
­interference, such as another Bluetooth device, cordless phone,microwave
oven, or wireless router.
•Reduce the number of applications running on your device. Running multiple
­applications can reduce the amount of internal ­resources ­available to transmit
audio. Closing non-essential ­applications may improve audio quality.
®
•Try turning off Wi-Fi on your device to improve audio quality.
•Try clearing your device from the speaker by disabling ­Bluetooth on your device.
Pair your device and the speaker again.
•If your device is in your pocket, try placing it in open air, without your body between
the device and the speaker.
•Turn the speaker off and back on.
•Reset the speaker. Press and hold Mute on the speaker for ten ­seconds until all
status ­indicators briefly illuminate and the speaker turns off. Turn the speaker on
again, and pair and connect your device.
•Check for updated software for your Bluetooth device, or go to owners.Bose.com
for updates to the SoundLink® Bluetooth® speaker III.
No audio or
poor sound
quality from
an AUX
device
•Ensure your connected device is on and playing audio.
•Ensure the 3.5 mm plug of the stereo cable is fully inserted into the speaker and
the other end into the AUX device.
•Press AUX on the speaker and ensure the AUX status indicator is on.
•Ensure the speaker is not muted and the speaker volume is up.
•If there is no sound, increase the volume level on the AUX device.
•If sound quality is poor, reduce the volume level on the AUX device.
•Try using a different AUX cable.
English - 17
Maintenance and Care
Replacing the battery
The battery should be replaced when:
• The battery status indicator continues blinking yellow after ten hours of charging.
• The period of battery operation noticeably decreases.
Only Bose can replace the battery in your speaker. If you need a new battery,
please contact the Bose organization in your country/region. For contact
information, refer to the contact list at the end of this guide or visit
http://global.Bose.com.
Cleaning the speaker
To clean the exterior surface of your product, wipe it using a soft, dry cloth.
• Do not use solvents, chemicals, or sprays.
• Do not allow liquids to spill or objects to drop into any openings.
Contacting customer service
For questions about the Bose® SoundLink® Bluetooth® speaker III, contact your
local Bose dealer. For ­contact information, refer to the contact list at the end of this
guide or visit http://global.Bose.com.
Limited warranty
Your Bose® SoundLink® Bluetooth® speaker III is covered by a limited warranty.
­ etails of the limited warranty are provided on the product registration card
D
­included in the carton. Refer to the card for instructions on how to register.
Failure to register will not affect your limited warranty rights.
Technical information
AC power supply rating
Input: 100 - 240V , 50/60 Hz, 600 mA
Output: 17 VDC, 1A Max
Input power rating
Input: 17 - 20 VDC, 1A Max
Dimensions
5.2" H x 10" W x 1.9" D (13.5 cm x 25.6 cm x 4.8 cm)
Weight
3.03 lb (1.37 kg)
Temperature range for use
32° to 113°F (0° to +45°C)
18 - English
Bose Corporation
USA
Bose Corporation, The Mountain
Framingham, MA 01701-9168
1-800-901-0472
Phone hours - ET (Eastern Time):
Weekdays 8:30 a.m. to 8 p.m.
Saturdays 9 a.m. to 3 p.m.
owners.Bose.com
Canada
Bose Limited
280 Hillmount Road, Unit 5
Markham, Ontario
Canada L6C 3A1
1-800-465-2673
Phone hours - ET (Eastern Time):
Weekdays 9 a.m. to 5 p.m.
www.Bose.ca
Australia
Bose Pty Limited, Unit 3/2 Holker Street
Newington NSW 2127
TEL 1 800 061 046 (AU)
TEL 008 501 511 (NZ)
FAX 612 8737 9924
www.Bose.com.au
www.Bose.com.nz
Belgique/België
Bose N.V., Limesweg 2
B-3700 Tongeren
TEL 012-259960
FAX 012-390840
www.Bosebelgium.be
China
Bose Greater China Operations
1st Floor, EYON Building, No. 118
East Dong Baoxing Road
Shanghai 200080 P.R.C.
People’s Republic of China
TEL 400-880-2266
FAX 021-65105380
Danmark
Bose A/S, Industrivej 7
2605 Brøndby
TEL 04343-7777
FAX 04343-7818
www.Bose.dk
Deutschland
Bose GmbH
Kundenbetreuung
Neuenhauser Str. 73
D-48527 Nordhorn
TEL 0800 2673444
www.Bose.de
Finland
Bose Finland
Kornetintie 6B
00380 Helsinki
TEL 10 778 69 00
FAX 10 778 69 09
www.Bose.fi
France
Bose S.A.S.
12 rue de Témara
78100 Saint Germain en Laye
TEL 01 30 61 63 63
FAX 01 30 61 63 60
www.Bosefrance.fr
Hong Kong
Nederland
Bose B.V.
Nijverheidstraat 8
1135 GE Edam
TEL 0299-390290
FAX 0299-390109
consumenteninfo@Bose.com
www.Bose.nl
Suite 1203, Midas Plaza, 1 Iai
Yau Street, San Po Kong
Kowloon, Hong Kong
TEL 852 2123 9000
New Zealand
India
Bose A/S
Kongsvinger Festning
2213 Kongsvinger
TEL +47 62 82 75 00
FAX +47 62 82 15 69
Bose Corporation India Private Limited
The Bose Service Centre
C13, Ground Floor
SDA Commercial Complex
Community Centre
New Delhi, India 110016
TEL 1 800 102 2673
FAX +91 11 47168650
Ireland
Bose SMS Ltd.
Castleblayney Road
Carrickmacross, Co Monaghan
TEL 1-800-932-436
FAX (042) 9671502
www.Bose.ie
Italia
Bose S.p.A. con socio unico
Via Spadolini 5
20141 Milano
TEL 06 60 292 292
www.Bose.it
Japan
Bose K.K.
Sumitomo Fudosan Shibuya
Garden Tower 5F,
16-17 Nampeidai-cho
Shibuya-ku, Tokyo 150-0036
TEL 0570-080-021
FAX 03-5489-1041
www.Bose.co.jp
Luxemburg
Bose N.V.
Limesweg 2
B-3700 Tongeren
TEL +32 12 259 960
FAX +32 12 390840
www.Bosebelgium.be
Mexico
Bose de Mexico S. de R.L. de C.V.
Paseo de las Palmas # 405
Despacho 204
Lomas de Chapultepec
C.P. 11000, Mexico D.F., Mexico
TEL +52 (55) 52 02 35 45
TEL +52 (55) 52 02 41 95
FAX +52 (55) 52 02 37 28
www.Bose.com.mx
TEL 0800 501 511
www.Bose.co.nz
Norge
Poland
Bose sp. z o.o.
ul. Woloska 12
02-675 Warszawa
TEL 22-852-2928
FAX 22-852-2927
www.Bose.pl
Österreich
Bose Ges.m.b.H.
Vienna Business Park
Wienerbergstrasse 7 (10.OG)
A-1100 Vienna
TEL 01-60404340
FAX 01-604043423
www.Bose.at
Schweiz
Bose AG
Hauptstrasse 134
4450 Sissach
TEL 061-9757733
FAX 061-9757744
www.Bose.ch
Sverige
Bose A/S
Johannefredsgatan 4
S-43153 Mölndal
TEL +46 774 - 450 450
FAX +46 31 - 274 89 15
United Kingdom
Bose Limited
1 Ambley Green
Gillingham Business Park
Gillingham, Kent ME8 ONJ
TEL 0800 081 3569
FAX 0870-741-4545
www.Bose.co.uk
World Wide Web
www.Bose.com
www.Bose.eu
global.Bose.com
English - 19
©2013 Bose Corporation, The Mountain,
Framingham, MA 01701-9168 USA
AM373985 Rev. 00
Download PDF