Yamaha | NS-120 | Owner's Manual | Yamaha NS-E120 Owner's manual

NS-E120
Thank you for selecting this Yamaha NS-E120
speaker system.
This model is designed mainly to be used as an effect
speaker system.
CONNECTION TO
YOUR AMPLIFIER
Natural Sound Bass-Reflex
Type Effect Speaker System
3 Remove your finger from the tab to allow it to lock
snugly on the cable’s wire end.
4 Test the security of the connection by tugging
lightly on the cable at the terminal.
BEFORE MAKING CONNECTIONS, MAKE SURE
THAT THE AMPLIFIER IS SWITCHED OFF.
PRECAUTIONS
Read these precautions carefully before operating
your speakers.
• When using an amplifier with a rated output power
higher than the music input of the speakers, care
should be taken never to exceed the speakers’
music input.
• Do not attempt to clean the speakers with chemical
solvents as this might damage the finish. To clean,
wipe with a dry, soft cloth.
• To prevent the enclosure from warping or
discoloring, do not place the speakers where they
will be exposed to direct sunlight or excessive
humidity.
• Do not place the speakers where they are liable to
be knocked over or struck by falling objects. Stable
placement will also ensure better sound
performance.
• Placing the speakers on the same shelf or rack as
the turntable can result in feedback.
• As these speakers contain strong magnets, avoid
placing watches, magnetic tapes, etc. near them.
Also, placing the speakers near a TV set may
impair picture color. If this happens, move the TV
set away from the speakers.
• Secure installing is the owner’s responsibility.
YAMAHA shall not be liable to any accident caused
by a failure in installing at a proper position and by
proper installation procedure.
m CONNECTIONS
• Connect the push-type input terminals at the rear of
the speakers to the speaker output terminals of your
amplifier with the supplied speaker cables.
• One side of the speaker cable is marked by a white
line. Connect the (+) terminals on both the amplifier
and the speakers using this white-marked side.
Connect the (–) terminals on both components
using the unmarked side of the cable.
• Connect the left speaker to the left (marked L)
terminals of your amplifier, and the right speaker to
the right (marked R) terminals, making sure not to
reverse the polarity (+, –). If one speaker is
connected with reversed polarity, the sound will be
unnatural and lack bass.
Procedures:
1 Press the tab on the terminal down, as shown in
the figure.
2 Insert the bare wire end properly into the terminal.
Press tab
Right speaker
White line
Left speaker
Speaker output
terminals of the
amplifier
White line
White line
SETTING UP THE SPEAKERS
Upright configuration
m Attaching the speakers to a wall
The speakers may be attached to a wall by using
the hooks provided on the speakers’ back panels.
Fasten wood screws into a firm wall or wall support
as shown in the diagram, and hang the speaker
hooks on the protruding screws.
SPECIFICATIONS
Type ......................................2-Way Bass-Reflex type
Speaker Unit ........12 cm paper cone woofer (JA1280)
2.5 cm semi-dome tweeter (JA05R8)
Crossover ..........................................6 kHz (6 dB/oct)
Input Terminal .............................................Push-type
Nominal Impedance .........................................6 ohms
Frequency Response ..........................70 Hz – 20 kHz
Nominal Input Power ............................................50W
Music Input Power ..............................................100W
Sensitivity ...................................................91 dB/Wzm
Dimensions (WxHxD)
.........................................220 mm x 297 mm x 89 mm
(8-5/8”x11-11/16”x3-1/2”)
Weight ....................................................1.8 kg (4 lbs.)
Accessories ..................2 speaker cables (10m each),
2 stands
100mm
∅4–5 mm
MIN.
12 mm
Side long configuration
Wall/
wall support
4 mm
Tapping
screw
(Available at the
market)
* Specifications subject to change without notice due
to product improvements.
80mm
WARNING:
* Each speaker weighs 1.8 kg (4 lbs.). Do not attach
them to thin plywoods or soft wall surface materials,
as the screws may tear free from flimsy surfaces,
causing the speakers to fall and be damaged, or
result in personal injury.
* Do not fasten the speakers to walls with nails,
adhesives, or other unsound hardware. Long-term
use and vibrations may cause them to pull free.
* To avoid accidents resulting from tripping over loose
speaker cables, fix these to the wall along with the
speakers.
m Setting the speakers on a shelf or rack
As shown in the figure, the speakers may be stood
in an upright or side-long configuration on either
shelves or racks, by attaching one of the supplied
stands to the back of each speaker.
NOTE:
The speakers can be hung on a wall in one of two
different configurations: vertically or horizontally.
The speaker hooks have been arranged so that the
speakers may be mounted in either of the two
configurations shown by the following figures.
Ex.) When setting
the speaker
upright
VP15950-0 BWWR,W Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising