Savaria | Omega | Omega Planning Guide 000822_31-m07-2014.fm

OMEGA
Curved Inclined Platform Lift
PLANNING GUIDE
Applicable Codes:
ASME A17.1
ASME A18.1
CAN/CSA B355
CAN/CSA B613
31-m07-2014
Part No. 000822
Copyright 2014
Savaria Corporation
All rights reserved.
Printed in Canada
Purpose of This Guide
This guide assists architects, contractors, and lift professionals to incorporate the
OMEGA Inclined Platform Lift into a residential or public building design.
The design and manufacture of the OMEGA Inclined Platform Lift meets the
requirements of the following codes and standards:
• ASME A18.1-2003 Section 3 (Public)
• ASME A18.1-2005 Section 3 (Public)
• ASME A18.1-2008 Section 3 (Public)
• ASME A18.1-2003 Sections 5 and 6 (Private)
• ASME A18.1-2005 Sections 5 and 6 (Private)
• ASME A18.1-2008 Sections 5 and 6 (Private)
• ASME A17.1-2000 Section 20
• ASME A17.1-2000 Section 21
• CAN/CSA B355 S1-02 (Public)
• CAN/CSA-B355-09 (Public)
• CAN/CSA B613-2000 (Private)
We recommend that you contact your local authority having jurisdiction to ensure
that you adhere to all local rules, regulations and fire regulations pertaining to inclined
platform lifts.
IMPORTANT: This Planning Guide provides nominal dimensions and specifications
useful for the initial planning of an inclined platform lift project. Dimensions and
specifications are subject to change without notice due to continually evolving
code and product applications.
Before beginning actual construction, please consult Savaria Corporation or the
authorized Savaria dealer in your area to ensure you receive your site-specific
installation drawings with the dimensions and specifications for your project.
Visit our website for the most recent drawings and dimensions.
How to Use This Guide
1
2
3
4
Determine your client’s intended use of the lift.
Determine the local code requirements.
Determine the site installation parameters.
Plan for electrical requirements.
History
February 6, 2012 – Initial release
February 14, 2012 – Corrected codes above
April 24, 2012 – Various updates throughout
June 28, 2012 – Revised pages 21, 22 and 23
September 5, 2012 – Added note regarding extra grabrail option to specifications
table on page 6 and added note to drawings on pages 18 and 20 regarding 1” space
requirement for folding/unfolding in tight spaces
December 13, 2012 – Revised speed and added minimum travel in specifications table
on page 6; Added support load diagram on page 16
January 10, 2013 - Revised NOTE on pages 18 and 20, revised tables on pages 21, 22
and 23
July 8, 2013 - Added Noise Level to specifications table on page 6
July 10, 2013 - Revised tables on page 21
May 13, 2014 - Revised drawing on page 21
May 14, 2014 - Revised text to indicate manual folding seat on pages 5, 6, and 7
July 31, 2014 - Revised Maximum Load in Specifications table on page 6
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
4
Contents
Description of the lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features and benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Specifications of the lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Lift components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Standard drive unit with remote controller box (top landing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Optional drive/controller cabinet (top landing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Overspeed governor (bottom landing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Lift controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Guide rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Guide rail mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
How the system works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Obstruction sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Safety arms and platform ramps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Safety brake (overspeed governor) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Limit switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Emergency stop button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
On-board alarm button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Platform key switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Landing light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Overspeed governor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Manual lowering device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Site verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Stairway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Minimum overhead clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Construction site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Electrical requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Main power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Structural requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Floor/support wall loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Support load diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Platform – 775 x 1250 mm (30.5 x 49.25”) Sheet 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Platform – 775 x 1250 mm (30.5 x 49.25”) Sheet 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Platform – 720 x 900 mm (28.3 x 35.4”) Sheet 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Platform – 720 x 900 mm (28.3 x 35.4”) Sheet 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lower level clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Turning clearances (90 degree curve) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Turning clearances (180 degree curve) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Standard drive unit clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Remote controller box dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Landing light box dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Optional drive/controller cabinet dimensions (sheet 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Optional drive/controller cabinet dimensions (sheet 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Call station dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Sample installation wiring layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
5
Description of the lift
The OMEGA Inclined Platform Lift is an accessibility device used to provide access over multiple
levels of straight stairs, stairs with intermediate landings, or stairs with turns.
The lift will transport a passenger either sitting in a wheelchair or on the manual folding seat.
The unit travels along the guide rails at a comfortable speed up to 14 feet per minute (0.07 metres
per second).
The unit is driven by a rope traction drive system. The standard drive unit is mounted on the rail
at the top of the stairs (for rail lengths under 20 metres) or in a optional drive cabinet (for rail
lengths over 20 metres).
The OMEGA is easy to operate using the on-board pendant control. When the lift is not in use, it
can be parked and folded up allowing access to the stairs.
The OMEGA is suitable for either indoor or outdoor use, and can be factory-built for left- or
right-side rail installations.
Features and benefits
• Major building renovations are usually not required as the OMEGA is installed on a modular
guide rail system that follows along an existing stairway. The rails will be securely fastened to a
supporting wall, the stairs, or both.
• The space-saving design of the platform and the rail system allows the platform to fit into
narrow staircases.
• The lift can be parked at the top or bottom of the staircase.
• A tight turning radius is possible.
• Inside or outside curve installations are accommodated.
• The lift platform is ADA-compliant.
• A compact standard drive is installed at the top of the rail system. An optional larger drive
cabinet can be used for longer runs (over 20 metres).
• The rope traction drive system allows for longer installation runs.
• A robust platform motor operates folding and unfolding of the platform, arms and ramps.
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
6
Specifications of the lift
Specification
Data
Maximum load
550 lb (250 kg) in Canada
660 lb (300 kg) in USA
Gradient
Variable up to 55°
Capacity
One person in wheelchair or sitting on the manual folding seat; seat capacity is 330 lb (150
kg)
Platform sizes
49.2” x 30.5” (1250 mm x 775 mm)
35.4” x 28.3” (900 mm x 720 mm)
Travel speed
12 feet/minute (0.06 metres/second)
Maximum travel
164 ft (50 m)
Minimum travel
8 in (20 cm)
Temperature
-31°F to +113 °F (-35°C to +45 °C)
Noise level (for typical
installation)
61.5 dBA (up direction); 60.8 dBA (down direction) 
Measured at a height of 1m, distance of 1m, in front of the motor with all panels on
Power supply
240 VAC (+/-5%)
Motor
1 hp (0.75 kW), 2.2 kW over 30 m
Pendant control buttons
Two constant-pressure directional buttons to move the lift up or down the stairway and an
emergency STOP button to stop the lift in an emergency
Remote call station buttons
Used to call/send the lift and fold/unfold the platform (call send only works with platform
folded up)
Platform control panel
Emergency STOP button to bring the lift to an immediate stop
Audible alarm button to signal for help
Key switch to enable use of the pendant control buttons
Standard features
Pendant control buttons (on platform)
Constant-pressure type buttons
Manual lowering capability (using handwheel)
Safety arms
Automatic folding platform
Limit switches
No machine room required
Emergency stop button
Audio visual alarm (running buzzer and light) to indicate the unit is in use
Manual folding seat (with seat belt)
Safety features
Edge sensors
Underpan sensors
Safety brake
Safety arms
Platform ramps
Emergency stop button
Limit switches
Manual operation (using handwheel)
Options
Outdoor package (requires outdoor rail)
Key switch for call station
Extra grabrail
90-degree ramp
NOTE: For the extra grabrail option to meet local code requirements, please confirm with the
factory if it is feasible depending on the stair angle and platform size before final approval.
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
7
Lift components
Landing
call station
Upper landing
stop position
Landing
call station
Intermediate landing
stop position
Carriage
Drive
Horizontal
rail
Upper rail
Landing
call station
Lower rail
Lower landing
stop position
Platform controls
Safety arms
Guide rails
On-board pendant
Seat belt
Carriage
Manual folding
seat
Overspeed governor
Platform
Access ramps
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
8
Standard drive unit with remote controller box (top landing)
Optional drive/controller cabinet (top landing)
Overspeed governor (bottom landing)
The overspeed governor is a safety
device located at the lower end of the
rail. It consists of an electrical switch and
a mechanical device that activate
together to stop the platform from
moving if it is descending down the
stairs too quickly.
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
9
Lift controls
The on-board, hand-held pendant has
constant-pressure UP/DOWN buttons
allowing you to move the platform up
or down the stairway. There is also a
red emergency STOP button.
PLATFORM PENDANT
Key switch Alarm button
(optional)
Emergency
stop button
PLATFORM CONTROL PANEL
Key switch – use to activate/de-activate
the platform pendant controls
Alarm button (if equipped) – use in an
emergency to sound an audible alarm
Emergency STOP button – use in an
emergency to stop the lift
UP
DOWN
FOLD
UNFOLD
UP/DOWN buttons – use to call the lift to the
required landing
FOLD/UNFOLD buttons – use to fold or unfold the
platform and raise or lower the ramps
KEY SWITCH (optional) – use to activate/de-activate
the call station controls
KEY SWITCH
(OPTIONAL)
CALL STATION
(for Automatic Platform)
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
10
Guide rails
The lift travels up and down the stairway along two guide rails – an upper rail and a lower rail. The
mounting location of the rails depends on the platform size and the angle of the stairs.
If the angle of the stairs is less than 20 degrees, a third rail (horizontal stabilizer rail) is required to
stabilize the platform. Horizontal rail sections may be required at half-landings or stop positions.
A sample horizontal rail installation is shown below.
Upper landing
stop position
Carriage
Horizontal
stabilizer
rail
Intermediate landing
stop position
Upper rail
Lower rail
Lower landing
stop position
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
11
Guide rail mounting
Wall
WALL MOUNTED
Step
Post
Railing
POST MOUNTED ON STEPS
Base plate
Step
Post
Railing
Spacers
POST MOUNTED ON SIDE OF STAIRS
Side of step
Post
POST MOUNTED TO WALL
Wall plates
Step
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
12
How the system works
The Omega carriage/platform assembly travels along a guide rail system that is custom designed
for each site. This railway consists of an upper tube and a lower tube that houses a continuous
loop of rope. The drive system moves the carriage/platform assembly up and down the stairs by
means of this rope.
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
13
Safety features
Obstruction sensors
During travel, the edges of the platform ramp and the carriage of the lift are protected by sensors
which stop the lift if it touches an obstacle.
There are also safety underpan sensors to detect an obstacle underneath the platform and
carriage and stop the lift.
Safety arms and platform ramps
While in motion, the platform is protected by two safety arms. The platform is also protected by
two side access ramps (and an optional front access ramp) which have the dual function of
facilitating access to the lift at the floors (open position) and of retaining the wheelchair while the
lift is in motion (safety position).
Before the lift leaves the floor, the safety arms must be down and the platform ramps must be up.
If the underpan or platform ramps encounter an obstacle as they move into position, a
microswitch is tripped, stopping the lift. You can drive away from the obstacle in the other
direction in order to remove the obstacle.
Limit switches
The upper and lower limit switches allow the lift to stop automatically in the correct landing
position at the upper or lower end of the staircase. If the upper or lower limit switch fails, the
additional final safety limit switch stops the unit.
Emergency stop button
There is a red emergency STOP button located on the platform control panel and on the handheld
pendant which can be pressed in an emergency to stop the lift.
On-board alarm button
The yellow alarm button is located on the platform control panel and can be pressed in an
emergency to sound an audible alarm indicating that assistance is required.
Platform key switch
The key switch is located on the platform control panel and is used to activate/de-activate the
platform pendant controls.
Landing light
The yellow landing light is mounted in view of each landing and the
travel of the lift, either at the middle landing or in the middle of travel
The landing light flashes to indicate that the unit is in use.
Overspeed governor (safety brake)
The overspeed governor is a safety device located at the lower end of
the rail. It will activate to quickly bring the lift to a stop if it is
descending down the stairs too quickly.
Manual lowering device
You can use the manual handwheel by inserting it on the motor shaft to bring the lift to the next
landing in the event of an emergency. You can also use an electric drill with the provided adapter
for faster lowering.
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
14
Site verification
Stairway
Due to close running clearances, the Owner/Agent must ensure that the stairs (where provided)
are level, plumb (+/-1/8” (3 mm)) and square and are in accordance with the dimensions specified
on the site-specific plan drawings.
Minimum overhead clearance
The Owner/Agent must ensure the minimum overhead clearance is in compliance with codes.
Construction site
The Owner/Agent is responsible for all masonry, carpentry and drywall work as required, and for
patching and finishing (including painting) all areas where walls/floors may need to be cut, drilled
or altered in any way to permit the proper installation of the lift.
Dimensions
The Contractor/Customer must verify all dimensions on the site-specific plan drawings and report
any discrepancies to the Agent or Distributor.
Installation
The equipment must be installed by a qualified technician in compliance with the codes
identified on the front cover of this manual.
The conformity for access to the platform is the distributor’s responsibility.
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
15
Electrical requirements
General
Electrical equipment and wiring must comply with Section 38 of CSA C22.1 (Canada) or
Section 620 of NEC ANSI/NFPA 70 (USA).
Main power supply
240 VAC (+/-5%), single-phase, 60 Hz, on a dedicated 15 amp circuit through a fused disconnect.
The disconnect should be installed close to the controller, if possible.
Contractor/customer to provide two 14 AWG conductors plus GND conductor between the fused
disconnect contact and the power supply box.
Lighting
Contractor/customer to provide lighting. Lighting must be a minimum of 100 Lux at the platform
and landings, and must have a switch and electrical GFCI outlet.
Contractor/customer to provide emergency lighting. Emergency lighting of 2 Lux must be
provided for a minimum of one hour on the platform along the travel route.
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
16
Structural requirements
Floor/support wall loads
A qualified professional must ensure that the building and stairway will safely support all loads
imposed by the lift equipment. Adequate structural support must be provided at the top landing,
bottom landing and throughout the supporting wall along the stairs.
The pull-out force on the supporting wall will vary depending on the type of rail mounting used
(wall brackets or support). Refer to the previous illustration of the guide rail mounting
configurations.
All wood studs in the supporting wall must be anchored in the ceiling and the floor to meet the
pull-out force requirements. Wood studs must be placed at 16” (404 mm) centres (minimum),
solidly anchored in the floor and ceiling.
The floor load will vary depending on the type of rail mounting used (wall brackets or support
posts on the steps).
Where required, the rail must be securely fastened to the structural support wall.
Support load diagram
POST-MOUNTED ON STEPS
WALL-MOUNTED
Lift rail
600 mm
(23.6”)
F
Note: As this
distance becomes
larger, the forces
become larger also.
Fh
Lift rail
83
Support post
Fh
Fh
600 mm
(23.6”)
Wall
bracket
F3
F2
z
Base plate
Fh
F = 3700 N (830 lbF)
Fh = 2770 N (625 lbF)
OMEGA Planning Guide
Fh = 2770 N (625 lbF)
F2 = 13120 N (2950 lbF)
F3 = 9420 N (2115 lbF)
z = 150 mm (6”)
Part No. 000822, 31-m07-2014
17
Platform – 775 x 1250 mm (30.5 x 49.25”), sheet 1
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
NOTES: An extra 1” of width is required to fold/unfold the platform in tight areas.
Post-mounted units need 3.5” more width.
18
Platform – 775 x 1250 mm (30.5 x 49.25”), sheet 2
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
19
Platform – 720 x 900 mm (28.3 x 35.4”), sheet 1
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
NOTES: An extra 1” of width is required to fold/unfold the platform in tight areas.
Post-mounted units need 3.5” more width.
20
Platform – 720 x 900 mm (28.3 x 35.4”), sheet 2
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
21
S
Lower level clearances
F
H = 180 mm (7”)
L
B
C
Refer to the charts below for clearance values.
NOTE: The values in the charts could change due to site conditions.
LEGEND
L = Platform length
B = End of rail at bottom landing
C = End of platform at bottom landing
F = Top rail distance at top landing
P = Angle
S = Overhead minimum (see local code for details/restrictions)
L = PLATFORM LENGTH 1250 mm (49.25")
ANGLE (P)
B
15°
20°
25°
30°
35°
40°
45°
1586/62.4
1412/55.6
1315/51.8
1246/49.1
1192/46.9
1146/45.1
1106/43.5
C
F
CAN. CODE
S
US CODE
S
2147/84.5
1974/77.7
1880/74.0
1815/71.5
1768/69.6
1731/68.1
1701/67
-255/-10
-220/-8.7
-205/-8.1
-210/-8.3
-25/-1
-235/-9.3
-260/-10.2
1772/69.75
1835/72.25
1899/74.75
1972/77.625
2054/80.875
2203/86.75
2438/96
1960.6/77.2
2084.4/82.1
2214.6/87.2
2355.85/92.8
2514.6/99
2692.4/106
2899/114.1
C
F
CAN. CODE
S
US CODE
S
1797/70.7
1624/64
1530/60.2
1465/57.7
1418/55.8
1381/54.5
1351/53.2
-63.2/-2.5
-33.8/-1.3
-51/-2
-21/-0.83
-150/-5.9
-123/-4.8
-176/-6.9
1721/67.75
1772/69.75
1813/71.375
1867/73.5
1930/76
1997/78.625
2076/81.75
1870/73.6
1959/77.1
2052.6/80.8
2158/85
2272/89.4
2402/94.6
2553/100.5
L = PLATFORM LENGTH 900 mm (35.5")
ANGLE (P)
B
15°
20°
25°
30°
35°
40°
45°
1411/55.6
1237/48.7
1140/44.9
1071/42.2
1017/40
971/38.2
931/36.7
Values in tables: mm/inches (unless otherwise specified)
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
22
Turning clearances (90 degree curve)
81 mm (3.2”) NOMINAL VALUE
81 mm (3.2”) NOMINAL VALUE
D
F
UNIT ACCESS/MOUNTING
INLINE ACCESS
ACCESS RAMPS
WALL MOUNTED
200/7.9
POST MOUNTED
200/7.9
90 DEGREE ACCESS
WALL MOUNTED
POST MOUNTED
200/7.9
200/7.9
PLATFORM WIDTH (B) x LENGTH (L)
720x900 (28.3X35.5) 775x1250 (30.5X49.25)
D
D
1095/43.1
1207/47.5
1295/51
1159/45.6
1188/46.8
1267/49.9
1321/52
1397/55
F
1300/51.2
1385/54.5
1650/65
1740/68.5
NOTE: The running clearance is 19 mm (0.75”)
and is not included in the above calculations.
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
23
D
81 mm (3.2”) NOMINAL VALUE
81 mm (3.2”) NOMINAL VALUE
81 mm (3.2”) NOMINAL VALUE
DISTANCE MIN. 60 mm (2.4”)
Turning clearances (180 degree curve)
F
D
UNIT ACCESS/MOUNTING
INLINE ACCESS
ACCESS RAMPS
WALL MOUNTED
200/7.9
POST MOUNTED
200/7.9
90 DEGREE ACCESS
WALL MOUNTED
POST MOUNTED
200/7.9
200/7.9
PLATFORM WIDTH (B) x LENGTH (L)
720x900 (28.3X35.5)
775x1250 (30.5X49.25)
D
D
1095/43.1
1207/47.5
1295/51
1159/45.6
1267/49.9
1321/52
1397/55
F
1300/51.2
1385/54.5
1650/65
1740/68.5
Values in table: mm/inches
NOTE: The running clearance is 19 mm (0.75”)
and is not included in the above calculations.
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
24
Standard drive unit clearances
DRIVE UNIT
E
85/3.3
85/3.3
85/3.3
E
L=900/35.5
-75/-3
-75/-3
-75/-3
E
L=1250/49.25
For reference only; dimensions may vary.
Values in table: mm/inches
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
25
Remote controller box dimensions
508 mm (20”)
508 mm (20”)
Thickness: 305 mm (12”)
Dimensions are for reference only and may vary.
Landing light box dimensions
76 mm (3”)
73 mm (2.875”)
Thickness: 114 mm (4.5”)
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
26
Optional drive/controller cabinet dimensions (sheet 1)
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
27
Optional drive/controller cabinet dimensions (sheet 2)
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
28
Call station dimensions
OMEGA Planning Guide
Part No. 000822, 31-m07-2014
29
Sample installation wiring layout
/$1',1*/,*+7
Part No. 000822, 31-m07-2014
OMEGA Planning Guide
OMEGA
Curved Inclined Platform Lift
PLANNING GUIDE
Part No. 000822
Copyright  2014
Savaria Corporation
Lifts and Elevators
www.savaria.com
Sales
2 Walker Drive
Brampton, Ontario, L6T 5E1, Canada
Tel: (905) 791-5555
Fax: (905) 791-2222
Toll Free: 1-800-661-5112
Download PDF