AlkaWay AlkaLina alkaline User manual

DISCLAIMER: Because this kit is not installed by Alkaway or its agents we cannot be held responsible for preformance as a result of installation. Use of the kit implies acceptance of this condition.

AlkaLina

Hydrogen

Rich

Water and

Alkaline

Water

System manual:

Reverse

Osmosis

Add-on.

KEEP IT

HANDY

DISCLAIMER: Because this kit is not installed by Alkaway or its agents we cannot be held responsible for preformance as a result of installation. Use of the kit implies acceptance of this condition.

DISCLAIMER: Because this kit is not installed by Alkaway or its agents we cannot be held responsible for preformance as a result of installation. Use of the kit implies acceptance of this condition.

AlkaLina

Hydrogen

Rich

Water and

Alkaline

Water

System manual:

Reverse

Osmosis

Add-on.

KEEP IT

HANDY

DISCLAIMER: Because this kit is not installed by Alkaway or its agents we cannot be held responsible for preformance as a result of installation. Use of the kit implies acceptance of this condition.

AlkaLina Installation: RO

Congratulations on choosing the AlkaLina alkaline and hydrogen generating water system to be added to your Reverse Osmosis water filter.

By following the steps in this instruction sheet we know you’ll be able to have the best of both worlds - pure water - and superb hydrogen rich alkaline water.

Here’s what we’re going to do.

We are going to install the two AlkaLine filters between your Reverse Osmosis system and your faucet. Because there are so many Reverse Osmosis systems on the market, we will try to reduce installation steps to the basic ones that apply to all

RO’s.

WHERE ARE WE PUTTING IT? See the blue circle below.

AlkaLina RO 13 Oct 2014

How To Cut Tubing forJohn Guest Fittings

1. Use a very sharp knife or razor blade to get a clean right angle cut.

2. Check to make sure you have a nice clean & even end.

P2

A Friendly Hint:

If it looks too hard, maybe it is. Sometimes your original system has been installed in a way that it takes up most of the room undersink. Find a handy friend or a good plumber familiar with Reverse Osmosis systems.

What You’ve Received:

1. AlkaLina Cartridge with Quickfit connectors top and bottom

2. H2 Diffuser with Quickfit connectors top and bottom.

3. Clips to mount filters

4. 1/4” Hose.

5. pH Reagent

6. Spanner

H2 DIFFUSER

ALKALINA

Turn off your mains water at the tap feeding the RO.

This will be under the sink on your cold water feed pipe. (See RED ‘1’ on diagram). Turn ON your benchtop faucet.

Determine where you want to install the two filters.

Make locating marks and mount the clamps for the filters.

Locate the hose from the RO to the faucet. To locate this go to the underside of the faucet and trace the hose back. Cut it close to the RO (or remove it from the

RO)(See RED ‘2’ on diagram)

Cut sufficient hose to attach the RO to the inlet of the

AlkaLina. (See RED ‘5’ on diagram)

Turn on your cold water tap to resupply water to your

RO. Check if there are any leaks in your connections.

If so, turn off the cold water supply, turn on the faucet to relieve pressure. Remove the leaking hose, recut hose end square as shown above, and re-insert.

Turn on your cold water again and allow the water to flow through your benchtop faucet. Let it run for 5-10 minutes then turn off.

Mount the filters in the clamps

Attach the faucet hose to the outlet point of the H2 filter. (See RED ‘3’ on diagram)

Cut sufficient hose to go from the AlkaLina to the H2 cartridge inlet. Push hoses in hard, then push again to secure properly.. That’s all you need to to make it watertight. (See RED ‘4’ on diagram)

YOUR ALKALINA MAY ‘SPUTTER’ FOR SOME

TIME WHEN TURNED ON. THIS DEMONSTRATES

THAT THE HYDROGEN ENRICHED WATER IS

BEING CREATED. TRY TO DRINK THIS

‘FIRST SHOT’.

REMEMBER TO REGISTER YOUR

ALKALINA FOR WARRANTY.

REPLACING YOUR ALKALINA

CARTRIDGES

Helpful hint: Order your replacements before your system needs it.

In that way you have a chance for a simpler changeover and no loss of precious AlkaLina water.

CHANGING YOUR FILTERS

Only the Alkalina - your first and biggest cartridge - has an internal filter. Only this cartridge needs to be removed, opened, and the inner alkalizer replaced.

Turn off your cold water inlet and turn on your faucet. This will reduce water pressure making your job easy.

Remove both hoses from the Alkalina cartridge.

To do so, push a fingernail against the collar close to the hose. Push first and pull the hose after. (Diagram top P2)

Remove the cartridge from its clamps. Using the large ring spanner provided, undo the top cap from the AlkaLina. (This may not be easy! Try wrapping a tea towel around the lower section while using the spanner on the top).

Thoroughly wash and dry the opened cartridge. Then insert the new alkaliser cartridge. Screw on the cap, and reattach it to the clamps.

Attach the hoses you removed earlier by pushing them hard into the connectors.

Repeat the removal process with the H2 Diffuser cartridge. You should now have all hoses reconnected.

Turn on the cold water inlet tap. Turn off the faucet. Check for leaks.

Turn on the faucet. Let the water run for a few minutes then turn off.

And now... Take another drink of hydrogen infused wonder water!

ORDER YOUR

NEXT

ALKALINA

CARTRIDGE

SET or

REGISTER

YOUR

WARRANTY

PAY FOR YOUR

NEW FILTER

BY HELPING A

FRIEND.

Send us your interested friend’s name and earn

AlkaWay credit!

USA www.alkaway.com

UK www.alkaway.co.uk

AUSTRALIA alkaway.com.au

ALKALINA OPENED

NEW CARTRIDGE