Agilent J6801B

Agilent J6801B
Agilent
Distributed Network Analyzer
Data Sheet
Technology to quickly solve problems in
today’s complex fixed and mobile
networks
1
Network Analysis and Troubleshooting Solutions Overview
Agilent’s scaleable Network Analysis and Troubleshooting Solutions provide the
foundation of advanced protocol analysis. Take advantage of extensive diagnostic
capabilities for troubleshooting and optimizing voice, video, data networks, as well as 2G,
2.5G and 3G mobile networks.
Combine your DNA platform hardware with Signaling Analyzer software for mobile network testing, with
Network Analyzer software for fixed wireline network testing, and with Triple Play Analyzer software to test next
generation services over IP
The DNA hardware platform brings greater power for collecting and analyzing real-time
data over multiple technologies such as Ethernet, ATM, POS, Frame Relay, IPv6, MPLS,
VoIP, IPTV, HSDPA, HSUPA, UMTS, CDMA 2000, GPRS, etc.
The scaleable DNA hardware platform provides the foundation of advanced protocol
analysis architecture for fixed and mobile network application. Couple the hardware with
the Network Analyzer software application and you have a powerful wireline solution for
LAN and WAN networks; couple the DNA platform with the Triple Play Analyzer software
for IPTV, VoD, VoIP QoE analysis. Similarly, use the hardware in conjunction with
Signaling Analyzer software to create an advanced mobile network analysis solution for
2G, 2.5G and 3G technologies.
2
DNA Components
Hardware
Mobile
J6801B
DNA
J6802B
DNA MX
J6803B
DNA PRO
J7830A
Signaling Analyzer Real-Time
J7832A
Signaling Analyzer Offline
J6840A
Network Analyzer Software
J6839A
Network Analyzer Software Professional Edition
Signaling Analyzer Free Decode Viewer
Applications
Wireline
Network Analyzer Software Standard Edition
Triple Play
Line Interface Modules
(LIMs)
J6900A
Triple Play Analyzer
J6810B
J6811A
J6813B
J6815B
J6816B
J6817B
J6818A
J6820B
J6821A
J6824A
J6830A
J6831A
J6832A
J6828A
J6756B
J6826A
J6827A
STM-4/OC-12/STM-1o/OC3 LIM
STM-1o/OC-3 LIM
E3/T3 (DS3) LIM
T1/E1 (RJ45/48C & Bantam connectors) LIM
E1/T1 (RJ45/48C & DB9 connectors) LIM
E1 (75 Ohm BNC connectors) LIM
ATM25 LIM
V-Series LIM for the Agilent Network Analyzer Family.
Network Analyzer HSSI LIM
Network Analyzer Eight-port E1/T1 LIM
10BaseT and 10/100 BaseTX Ethernet LIM
10/100BaseFX Ethernet LIM
1000BaseX Ethernet LIM
4-Port OC-3/STM-1 LIM Multiplexor.
Network Analyzer HSSI Tap
Eight-port T1/E1 Balanced Monitor Tap
Eight-port E1 BNC Monitor Tap
J7833A
Call Manager Database
J7831A
Multi-User
J6848A
Report Center
J5479A
Voice Quality Tester
J6782A
Network Troubleshooting Center
Instrument Manager
Additional Utilities
Select Network Analyzer LIM
Agent Config
J6835A
NDIS Server
NTP Time
File Translator
Time Sync Data File Merge Utility
3
DNA Hardware Platforms
Acquisition System
DNAs accept any LAN or WAN LIM
LIMs can be hot-swapped
Operates on two ports per LIM
Operates with the following link-layer technologies:
- ATM
- CiscoSLE
- Ethernet
- Frame Relay
- HDLC/SDLC
- LAPB
- LAPD
- Packet over SONET/SDH (IETF RFC 2615/1662, 1619/1662, Cisco HDLC)
- PPP (RFC 1662, 1663)
Capture buffer:
- Capture rate: Full line rate per port on any installed LIM up to half-duplex rates
up to 1 Gb/s and full-duplex rates up to 2 Gb/s
- Buffer memory size (used for user data and associated analyzer overhead):
- user adjustable up to 512MB for J6801B DNA and J6803B DNA PRO and 256
MB for J6802B DNA MX, shared equally between both ports
- Data time stamp resolution is 100 ns
Hardware real-time capture filters:
- 100% line rate filtering
- 32 filters
Auto-encapsulation discovery for LAN over WAN
Real time auto discovery and reassembly:
- ATM cell VPI:VCI for AAL5 and AAL2 to OC-12/STM-4
Traffic Generation:
- At 100% line rate for LAN and ATM (except for J6824A/J6828A)
- Scenario replay for LAN
4
DNA Platform Time Synchronization
GPS
Synchronize any number of
DNAs worldwide for timecorrelated measurements
Accuracy of ±1 µs for LAN
and ±5 µs for WAN/ATM
Control & Sync
Time-synchronize a daisy-chain
of up to 10 DNAs in a 20 meter
cable from a DNA PRO or DNA
MX
Accuracy of ± 500 ns for LAN,
and 5 µs for WAN/ATM
¥
¥
¥
DNA
DNA MX
DNA PRO
¥
¥
¥
Network Time Protocol (NTP)
Time-synchronize DNA MX and
DNA PRO to an external NTP
server
Accuracy of ± 20 ms
¥
¥
DNA Platform Telemetry
The DNA platform provides flexible options for telemetry.
10/100 Mbps Ethernet
Single-port 10/100/1000 Ethernet
Combo 10/100 Ethernet / 56k Modem
Dual-port 10/100/1000 Ethernet
J6801B DNA
Standard
NA
NA
NA
J6802B DNA MX
Standard
Option 001
Option 002
Option 003
802.11 a/b/g WLAN
NA
NA
J6803B DNA PRO
Standard
Option 001
Option 002
Option 003
Option 202 for Europe
Option 203 for Japan
Option 204 for rest of the world
Run-Time Store to Media
The DNA platform allows you to collect and analyzer data over long periods of time by
utilizing unique data streaming capabilities. In RTSM (run-time store to media) mode, the
instruments export processed information in run time through external ports.
The J6801B DNA, J6802B DNA MX and J6803B utilize the control & sync port to
stream data up to 55 Mbps.
The J6801B and J6803B, in addition, have an external gigabit Ethernet port with
capabilities of streaming media up to 400 Mbps when using the Signaling Analyzer MultiUser software.
5
J6801B DNA
J6801B Distributed Network Analyzer
The DNA consists of one acquisition system that supports any available LAN or WAN
LIM, plus a built-in power supply. It has its own IP address and is controlled via TCP/IP
over Ethernet from a standard PC running the Network Analyzer Software (included with
the analyzer for use with the controlling PC), from Signaling Analyzer software, or
directly from a DNA PRO or DNA MX.
DNAs are used for remote and distributed troubleshooting and can be used in standalone
mode connected to a PC, or daisy-chained together to create multi-port with timesynchronization test systems. Distributed remote operation is possible, allowing one or
more DNAs to be operated remotely over a LAN.
-
Built-in power supply for with AC or DC options
Rackmountable
Network Analyzer Software CD with a single-use license
Control: TCP/IP over 10/100Base-TX via RJ-45 Control & Sync In connector
from:
o Control & Sync Out connector of a DNA PRO, DNA MX or another
DNA
o A standard PC/laptop directly connected via Ethernet, or indirectly
connected via a LAN or an Internet
- Time Synchronization:
o Control & Sync: From an upstream a DNA PRO, DNA MX or DNA via
the Control & Sync In interface. Up to 10 daisy-chained, timesynchronization DNAs can be connected to a DNA PRO or DNA MX.
o GPS: via 10 MHz (75 Ohm), 1 pps (75 Ohm) & RS-232C from
external GPS receiver
o From external NTP server
- Run-Time Store to Media up to 400 Mbps
6
J6802B DNA MX
J6802B Distributed Network Analyzer MX
The DNA MX is a rack-mountable analyzer with a built-in acquisition system that supports
any available LAN or WAN LIM. It includes an embedded processor with removable hard
disk drive storage, CD-RW drive and a built-in AC or 48 Volt DC power supply. Should
testing with additional interfaces be necessary, the DNA MX supports multiple directly
attached J6801B DNAs with full time synchronization between the test interfaces.
Network Analyzer Software running on the embedded processor is used to control the
internal acquisition system and any directly attached DNAs. The DNA MX is accessed
and controlled from an external PC via a web browser (requiring no other software), from
Instrument Manager or from a PC that is running Network Troubleshooting Center
software.
Included with each DNA MX is a choice of 10/100/1000 Mbps PC card or combo 56
kbps modem and 10/100 Mbps PC Card for telemetry purposes.
- Built-in controller:
o 2.8 GHz Intel Pentium 4 CPU
o 1 GB DDR 333MHz memory
- Removable 120 GB hard disk drive
- CD RW drive
- Telemetry/Auxiliary ports:
o Single-port 10/100/1000 Ethernet (default)
o Dual-port 10/100/1000 Ethernet
o Combo 10/100 Ethernet/ 56kbps modem
- Two USB 2.0 ports
- Time Synchronization:
o GPS: via 10 MHz (75 Ohm), 1 pps (75 Ohm) & RS-232C from
external GPS receiver
o NTP: Network Time Protocol via 10/100 Ethernet telemetry port
o From external NTP server
- Network Analyzer Software pre-loaded on built-in controller
- Network Analyzer Instrument Manager (for downloading to controlling PC)
- System Recovery CD
- Run-Time Store to Media
- Optional –48 V DC Power Supply Available
7
J6803B DNA PRO
J6803B Distributed Network Analyzer PRO
The DNA PRO is a portable analyzer with a built-in acquisition system that supports any
available LAN or WAN LIM. It includes an embedded processor with removable hard disk
drive storage and a built-in power supply. Should testing with additional interfaces be
necessary, the DNA PRO also supports multiple directly attached DNAs with full time
synchronization between the test interfaces.
Network Analyzer Software running on the embedded processor is used to control the
internal acquisition system and attached DNAs. The DNA PRO is accessed and controlled
from an external PC via a Windows-based Web browser, Instrument Manager or
Network Troubleshooting Center software.
- Built-in controller:
o 1.6 GHz Intel Pentium M CPU
o 1 GB DDR 333MHz memory
- Removable 60 GB hard disk drive
- Telemetry ports:
o Single-port 10/100/1000 Ethernet (default)
o Combo 10/100 Ethernet/ 56kbps modem
o Dual-port 10/100/1000 Ethernet
o Optional 802.11a/b/g wireless LAN (region specific)
- Two USB 2.0 ports
- Time Synchronization:
o GPS: via 10 MHz (75 Ohm), 1 pps (75 Ohm) & RS-232C from
external GPS receiver
o NTP: Network Time Protocol via 10/100 Ethernet telemetry port
o From external NTP server
- Network Analyzer Software pre-loaded on built-in controller
- Network Analyzer Instrument Manager (for downloading to controlling PC)
- System Recovery CD
- Run-Time Store to Media
8
DNA Software Applications
The DNA platform is capable of running software applications for mobile or cellular
communications, as well as applications for wireline communication networks. For detail
explanation of these software applications, please consult the Signaling analyzer
Technical Overview and the Network Analyzer Technical Overview documents.
Signaling Analyzer Applications
J7830A Signaling Analyzer Real-Time
Signaling Analyzer Real-Time is a high-performance solution for 2, 2.5 and 3G system
verification, troubleshooting, and RAN optimization. Its intelligent call trace-centric
approach enables distributed call trace, performance measurements, and drill-down
problem isolation for calls on UMTS, GSM, and CDMA RANs, as well as the mobile core,
IMS, PSTN and Internet. Consult the signaling Analyzer Technical Overview document for
a detail description of the capabilities of this products and configuration options.
J7832A Signaling Analyzer Offline
Signaling Analyzer Offline is a perfect companion of the Signaling Analyzer Real-Time.
The Signaling Analyzer Offline allows you to do post capture analysis of 2, 2.5 and 3G
networks. Its intelligent call trace-centric approach enables distributed call trace,
performance measurements, and drill-down problem isolation for calls on UMTS, GSM,
and CDMA RANs, as well as the mobile core, IMS, PSTN and Internet.
Signaling Analyzer Free Decode Viewer
Signaling Analyzer Free Decode Viewer is an application that allows to decode capture
traces from Signaling analyzer Real-Time.
This application is free of charge and can be downloaded from
www.agilent.com/find/sart.
Network Analyzer Applications
J6840A Network Analyzer Software
A single-use license key of the Network Analyzer Software is included with the
Distributed Network Analyzer acquisition platform and is auto-licensed on the DNA MX
and DNA PRO platforms. Network Analyzer Software can also be purchased separately
as the J6840A product. This software performs the following functions:
- Control of the DNA hardware via TCP/IP and control of the DNA MX and DNA
PRO acquisition hardware.
- Network measurement and analysis for LAN and WAN environments.
- Support for network traffic acquisition and analysis using an NDIS network
interface card (NIC) for LAN technologies (10/100/1000 Ethernet, Token Ring,
FDDI) on the local PC.
- Control of the Network Analyzer NDIS Server (J6835A).
- Off-line Analysis, providing users with full protocol analysis capabilities on saved
capture data (display filtering, searching, decoding, etc.) without connecting to
acquisition hardware (e.g. DNA). Data files captured on an Agilent Advisor can
also be analyzed.
9
J6839A Network Analyzer Software Professional Edition
Network Analyzer Software Professional Edition performs the following functions:
- Real-time network measurement and analysis for LAN and off-line analysis for
LAN and WAN environments.
- Support for network traffic acquisition and analysis using an NDIS network
interface card (NIC) for LAN technologies (10/100/1000 Ethernet, Token Ring,
FDDI) on the local PC.
- Control of the Network Analyzer NDIS Server (J6835A).
- Off-line Analysis, providing users with full protocol analysis capabilities on saved
capture data (display filtering, searching, decoding, etc.) without connecting to
acquisition hardware (e.g. DNA). Data files captured on an Agilent Advisor can
also be analyzed.
Network Analyzer Software Standard Edition
Network Analyzer Software Standard Edition is free of charge network analysis software
suitable for evaluation purposes and for entry-level use.
- It can determine who is on your network, who is using bandwidth, and where
errors may be occurring on the network, identifying problems before they
become serious issues that impact productivity and performance.
- Expert analysis tools can be used to solve network problems quickly and
effectively by reducing thousands of IP and Novell frames into a handful of
significant events.
- It can capture and analyze network traffic in real-time using your PC’s local
NDIS Ethernet adapter.
- It can analyze LAN data offline and quickly pinpoint problems on your network.
Download the software and obtain a 6-month License Key at
www.agilent.com/comms/freenetworkanalyzer.
J6835A Network Analyzer NDIS Server
Network Analyzer NDIS Server is a remote software agent process that is able to connect
to an NDIS-based NIC and capture data in promiscuous mode, performing various
analysis tasks. Measurements on 10/100/1000 Mbps Ethernet, Token Ring or FDDI NICs
are supported. This server is accessed from the Network Analyzer Software client and
does not, itself, contain an analysis GUI.
Triple Play Applications
J6900A Triple Play Analyzer
The Agilent J6900A Triple Play Analyzer is the most complete in-service analysis and
troubleshooting tool in a single solution for network equipment manufacturers and
communication service providers, who develop, install and troubleshoot voice, data and
video applications. The analyzer provides accurate measurements of VoIP, IPTV and VoD
Quality of Experience as well as channel zapping analysis. The analyzer helps customers
realize faster time to market and decrease operational costs by passively testing any
technology, over any interface, from anywhere and by anyone.
10
Line Interface Module (LIM)- Specifications
General
Network Analyzer LIMs provide physical layer and link layer connectivity to the
embedded data acquisition and real-time systems in these products:
- J6801B DNA
- J6802B DNA MX
- J6803B DNA PRO
They also gather physical and link layer statistics. For example, LIMs handling ATM
provide real-time AAL-2 and AAL-5 reassembly on thousands of virtual channels
simultaneously, and provide ATM and AAL error statistics. All LIMs have the hardware
resources to generate traffic for their associated network technologies.
Connection Configurations
Depending on the type of LIM, they provide any of the following connection
configurations:
- WAN Terminated Mode – uses one input and one output of WAN LIMs
- WAN Bridged Monitor Mode – uses both inputs and outputs of WAN LIMs for
bi-directional monitoring at test access points; high input impedance should
normally be selected.
- WAN Jack Monitor Mode – uses both inputs of WAN LIMs only for bidirectional monitoring at protected monitor points.
- WAN Through Monitor Mode – uses both inputs and outputs of WAN LIMs
providing bi-directional repeater functionality plus bi-directional monitoring
functionality. Each receiver input is terminated.
- LAN Node Mode – uses an interface port of LAN LIMs to transmit and receive
- LAN Monitor Mode – uses both interface ports of LAN LIMs to monitor traffic
passively between two devices
The operation of the physical interface is often critical in determining the cause of
network problems. Therefore, the acquisition system tracks errors at the physical layer.
Signal events are recorded on the display for both the line (network) side as well as the
equipment (user/subscriber) side. The time of the last occurrence of a particular event is
recorded as well.
Advanced Statistics
LIMs provide advanced statistics for layer 1 and 2 measurements. Please refer to the
Network Analyzer Technical Overview for a detailed description of the following statistics
performed in LIMs:
- Physical Layer Status and Link Layer (VPI.VCI and DLCI) Statistics
- Common Statistics (cell mode ATM, frame mode ATM, and Frame Relay)
- ATM Statistics (cell mode)
- ATM Statistics (frame mode)
- Frame Relay Statistics
- Length Statistics (frame mode ATM, and Frame Relay)
- ATM Policing
- ATM Usage Expert (Traffic Contract Estimation)
- 1-Point CDV
- Traffic Generation
11
J6810B STM-4/OC-12/STM-1o/OC-3 LIM
(622.080/155.520 Mbps)
J6810B STM-4/OC-12/STM-1o/OC-3 LIM
General
The dual-rate LIM handles ATM, Packet over SONET/SDH and Frame Relay at 622 Mbps
and 155 Mbps, and performs ATM and WAN analysis on lower-rate submultiplexes/tributaries down to fractional E1/DS1 rates.
When analyzing ATM at any supported rate, real-time AAL-2 and AAL-5 reassembly is
performed simultaneously on up to 5120 virtual channels and the resulting frames are
passed from the LIM to the acquisition system for further analysis. Cell mode is also
available. ATM Policing can be performed on up to 1024 virtual circuits in frame mode or
cell mode simultaneously with other measurements.
The functionality of this LIM can be enhanced with the addition of the J6828A Dual 4Port STM-1/OC-3 External LIM.
The LIM has dual-rate optical interfaces and can be used in single-mode or multi-mode
environments; when used in multi-mode environments, 10 dB attenuators should be used
on the optical outputs (a pair of suitable attenuators is supplied with the LIM).
Note: Both SDH and SONET framing are fully supported in this LIM; the SDH terminology
is given first (that is, SDH/SONET); SONET terminology has recently changed and the
newer terminology is used here with older terms shown in parentheses, where
appropriate.
Common to Inputs and Outputs:
Framing:
SDH: STM-4, STM-4c and STM-1, ITU-T G.707
SONET: STS-12, STS-12c, STS-3 and STS-3c, GR-253
SDH / SONET Frame Scrambling (x7 + x6 + 1)
ATM Cell Scrambling: conforms to ITU-T I.432.1 (x43 + 1) and may be turned on
(default) or off
12
Inputs:
Two input ports (single-mode/multi-mode compatible)
Connectors: LC-PC
Monitor modes:
- Through monitor mode: uses both inputs and outputs; signal is terminated and
regenerated
- Test access point monitor mode; uses inputs only
Sensitivity:
- Typ. –32 dBm
- Min. –28 dBm
- Max. –8 dBm (receiver overload limit)
Loss of Signal Detect Level: -34 dBm (typical)
Receiver wavelength range: 1310/1550 nm
Real-Time Optical Power measurement for each LIM port:
- Dynamic Range: +0.5 dBm to –32 dBm
- Accuracy @ 1310 nm:
o ±1 dBm +0.5dBm down to –15dBm
o ±3 dBm –15dBm down to –32dBm
Physical Layer line status indications for each LIM port (SDH / SONET):
- Loss of Signal (LOS)
- Loss of Frame (LOF)
- Loss of Pointer (LOP)
- Loss of Cell Delineation (LCD)
- MS-RDI / RDI-L (Line FERF)
- RDI / RDI-P (Path FERF)
- MS-AIS / AIS-L (Line AIS)
- AIS / AIS-P (Path AIS)
Physical Layer line vital counts for each LIM port (SDH / SONET):
- MS-RDI / RDI-L (Line FERF)
- RDI / RDI-P (Path FERF)
- MS-AIS / AIS-L (Line AIS)
- AIS / AIS-P (Path AIS)
- MS-REI / REI-L (Line FEBE)
- REI / REI-P (Path FEBE)
- B1 BIP errors
- Loss of Cell Delineation (LCD) –performed at selected level of demultiplexing
Physical Layer Demultiplexing: see SDH and SONET Tributary Analysis diagrams
Demux for one tributary of T1/E1 without demux and channelization license
ATM Layer at any supported rate for each LIM port (network and equipment):
- Full rate cell processing
- Auto-discovery and notification of up to 5120 virtual channels (VPI-VCI)
- ATM policing, traffic contract estimation and 1-point CDV
ATM Adaptation Layer (AAL) – frame mode:
- Auto-discovery and notification of up to 5120 AAL-2 Channels (VPI-VCI-CID)
and/or AAL-5 virtual channels (VPI-VCI), any mix of AAL-2 and AAL-5
- Concurrent real-time reassembly of the first 4000 bytes of multiple AAL-2 SSCS
PDUs at all rates up to 622 Mbps (corner case: reassembly of long sequences of
shortest possible CPS packets at 622 Mbps is best effort)
- Count of total AAL-2 SSCS PDUs
- AAL-2 SSCS PDUs are reassembled to the SSSAR sub-layer
- Concurrent real-time reassembly of the first 4000 bytes of multiple AAL-5 SSCS
PDUs (guaranteed at all rates up to 622 Mbps)
- Count of total AAL-5 SSCS PDUs
- Reassembly of any mixture of up to 5120 AAL-2 and AAL-5 SSCS PDUs
- Reassembled AAL-5 SSCS PDUs with trailer CRC-32 errors
ATM and AAL statistics per VPI.VCI collected on multiple VCs
13
Packet over SONET/SDH analysis configurations supported:
- IETF PPP in HDLC: RFC 1662 and both current RFC 2615 (x43 + 1 scrambled
- SONET/SDH payload) and obsolete RFC 1619 (unscrambled SONET/SDH
payload) versions with version auto-detect based on POH C2 byte value
(default) and manual override for scrambling enable/disable
- Cisco HDLC over SONET/SDH
- FCS-16 and FCS-32 auto-detect and manual override
Frame Relay over SONET/SDH analysis configuration supported as per FRF.14
WAN analysis supported (at tributary rates shown in SDH and SONET Tributary Analysis
diagrams):
- Frame Relay, HDLC/SDLC, sync PPP
WAN Statistics for the selected configuration on each LIM port:
- Total frames
- Bridged frames
- Bridged broadcast frames
- Bridged multicast frames
- Total octets
- Throughput (kbps)
- Aborted frames
- Short frames
- FCS errors
Frame Relay statistics per DLCI collected on 1024 VCs
Capture rate
Full rate, full duplex, at all supported configurations up to 622 Mbps
Outputs:
Two output ports
Connectors:
LC-PC
1310nm Class 1 laser (single mode, but multi-mode fiber compatible with 10 dB
attenuator)
Output levels:
Min. –15 dBm
Max. –8 dBm
Clocking:
Recovered (loop)
Traffic Generation:
Full rate ATM traffic generation at 155 Mbps (over STM-1/OC-3) and 622 Mbps
(over STM-4/OC-12)
14
Tributary Analysis
The following two diagrams depict the multiplexing functionality of the STM-4/OC12/STM-1o/OC-3 LIMs. These interfaces allow connecting to a higher rate link, and
internally demultiplexing the packets to get into a specific tributary for in-depth
troubleshooting.
ST M-4
AU-4-4c
VC-4-4c
C-4-4c
Bulk Filled
AT M
P OS
C-4
Bulk Filled
AT M
P OS
C-3
Bulk Filled
AT M
P OS
AUG#
1 of 4
ST M-1
AUG
AU-4
VC-4
TUG-3#
1 of 3
TUG-3
TU-3
VC-3
AU-3#
1 of 3
AU-3
AT M
W AN
VC-3
DS3
TUG-2#
1 of 7
TUG-2#
1 of 7
DS2
DS1
NxDS0
DS2#
1 of 7
DS1#
1 of 4
Timeslot s
N of 24
E2
E1
Nx64k
E2#
1 of 4
E1#
1 of 4
Timeslot s
N of 31
DS1
NxDS0
AT M
W AN
Nx64k
AT M
W AN
AT M
W AN
TUG-2
E3
TU-11#
1 of 4
TU-11
C-11
VC-11
async
mapping
TU-12#
1 of 3
TU-12
VC-12
C-12
Timeslot s
N of 24
E1
async
mapping
Timeslot s
N of 31
J6810B LIM SDH Configurations
OC-12
ST S-12
ST S-12c
ST S-12c SPE
Bulk Filled
AT M
P OS
ST S-3c
ST S-3c SPE
Bulk Filled
AT M
P OS
Bulk Filled
AT M
P OS
ST S3#
1 of 4
OC-3
ST S-3
ST S1#
1 of 3
ST S-1
ST S-1 SPE
AT M
W AN
DS3
VT group#
1 of 7
DS2
DS1
NxDS0
DS2#
1 of 7
DS1#
1 of 4
Timeslot s
N of 24
E2
E1
Nx64k
E2#
1 of 4
E1#
1 of 4
Timeslot s
N of 31
DS1
NxDS0
AT M
W AN
VT group
E3
VT1.5#
1 of 4
VT1.5
VT1.5 SP E
async
mapping
Timeslot s
N of 24
VT2#
1 of 3
VT2
VT2 SP E
E1
async
mapping
AT M
W AN
Nx64k
AT M
W AN
Timeslot s
N of 31
J6810B LIM SONET Configurations
15
J6811A STM-1o/OC-3 LIM
(155.520 Mbps)
J6811A STM-1o/OC-3 LIM
General
This LIM handles ATM and Packet over SONET/SDH at 155 Mbps. When analyzing ATM,
real-time (full rate) AAL-2 and AAL-5 reassembly is performed simultaneously on more
than 5120 virtual channels and the resulting frames are passed from the LIM to the
acquisition system for further analysis. Cell mode is also available. ATM Policing can be
performed on up to 1024 virtual circuits in frame mode or cell mode simultaneously with
other measurements.
The LIM has optical interfaces and can be used in single-mode or multi-mode
environments; when used in multi-mode environments, 10 dB attenuators should be used
on the optical outputs. Both SDH and SONET framing are fully supported in this LIM.
Common to Inputs and Outputs:
Framing:
- SDH: STM-1, ITU-T G.707
- SONET: STS-3c, GR-253
SDH / SONET Frame Scrambling (x7 + x6 + 1)
ATM Cell Scrambling: conforms to ITU-T I.432.1 (x43 + 1) and may be turned on
(default) or off
Inputs:
Two input and output ports (single-mode/multi-mode compatible)
Connectors: SC-PC
Monitor modes:
- Through monitor mode: uses both inputs and outputs; signal is terminated and
regenerated
- Test access point monitor mode; uses inputs only
Sensitivity:
- Typ. –32 dBm
- Min. –28 dBm
Loss of Signal Detect Level:
–34 dBm
Receiver wavelength range: 1310/1550 nm
Optical power measurement for each LIM port:
+3 dBm to –42 dBm dynamic range in steps of 0.1 dBm
±0.5 dBm absolute accuracy at 1310 nm
(can also be used to measure power at 622Mbps)
16
Physical Layer line status indications for each LIM port (SDH / SONET):
- Loss of Signal (LOS)
- Loss of Frame (LOF)
- Loss of Pointer (LOP)
- Loss of Cell Delineation (LCD)
- MS-RDI / RDI-L (Line FERF)
- RDI / RDI-P (Path FERF)
- MS-AIS / AIS-L (Line AIS)
- AIS / AIS-P (Path AIS)
Physical Layer line vital counts for each LIM port (SDH / SONET):
- MS-RDI / RDI-L (Line FERF)
- RDI / RDI-P (Path FERF)
- MS-AIS / AIS-L (Line AIS)
- AIS / AIS-P (Path AIS)
- MS-REI / REI-L (Line FEBE)
- REI / REI-P (Path FEBE)
- B1 BIP errors
- Loss of Cell Delineation (LCD)
ATM Layer at any supported rate for each LIM port (network and equipment):
- Full rate cell processing
- Auto-discovery and notification of up to 5120 virtual channels (VPI-VCI)
- ATM policing, traffic contract estimation and 1-point CDV
ATM Adaptation Layer (AAL) – frame mode:
- Auto-discovery and notification of up to 5120 AAL-2 Channels (VPI-VCI-CID)
and/or AAL-5 virtual channels (VPI-VCI), any mix of AAL-2 and AAL-5
- Concurrent real-time reassembly of the first 4000 bytes of multiple AAL-2 SSCS
PDUs
- Count of total AAL-2 SSCS PDUs
- AAL-2 SSCS PDUs are reassembled to the SSSAR sub-layer
- Concurrent real-time reassembly of the first 4000 bytes of multiple AAL-5 SSCS
PDUs
- Count of total AAL-5 SSCS PDUs
- Reassembly of any mixture of up to 5120 AAL-2 and AAL-5 SSCS PDUs
- Reassembled AAL-5 SSCS PDUs with trailer CRC-32 errors
- ATM and AAL statistics per VPI.VCI collected on multiple VCs
Packet over SONET/SDH analysis configurations supported:
- IETF PPP in HDLC: RFC 1662 and both current RFC 2615 (x43 + 1 scrambled
- SONET/SDH payload) and obsolete RFC 1619 (unscrambled SONET/SDH
payload) versions with version auto-detect based on POH C2 byte value
(default) and manual override for scrambling enable/disable
- Cisco HDLC over SONET/SDH
- FCS-16 and FCS-32 auto-detect and manual override
Capture rate: Full line rate (full duplex)
Outputs:
1310nm Class 1 laser (multi-mode fiber compatible with 10 dB attenuator, available
separately as J2928A)
Output levels:
- Min. –12 dBm
- Max. –7 dBm
Clocking:
- Recovered (loop)
Traffic Generation: Full rate ATM traffic generation
17
J6813B E3/T3 (DS3) LIM
(34.368 / 44.736 Mbps)
J6813B E3/T3 (DS3) LIM
General
The J6813B LIM supports ATM, Frame Relay, HDLC, SDLC and PPP. When analyzing
ATM, real-time (full rate) AAL-2 and AAL-5 reassembly is performed simultaneously on
more than 5120 virtual channels and the resulting frames are passed from the LIM to the
acquisition system for further analysis. Cell mode is also available. ATM Policing can be
performed on up to 1024 virtual circuits in frame mode or cell mode simultaneously with
other measurements. The module can be configured for use as an E3 or T3 interface.
Common to Inputs and Outputs (E3 and T3):
Two input and output ports
Connectors: 75 Ohm BNC female
When E3 is selected:
Electrical: ITU-T G.703
Line Code: HDB3
Framing:
Frame Relay: ITU-T G.751
ATM: ITU-T G.832
ATM Cell Mapping:
Direct (ITU-T G.804)
ATM Cell Scrambling:
Conforms to ITU-T I.432.1 (x43 + 1) and may be turned on or off
When T3 is selected:
Electrical:
- ITU-T G.703
Line Code:
- B3ZS
Framing:
- C-bit and M13 (auto-select on input side)
Fractional DS3:
- any DS0 or combination of DS0s within any DS1 within DS3
ATM cell Mapping:
- Direct (normal mode, ITU-T G.804)
- PLCP (obsolescent mode, ITU-T G.804)
ATM Cell Scrambling:
- Conforms to ITU-T I.432.1 (x43 + 1) and may be turned on or off
18
Inputs (E3 and T3):
Received pulse amplitude measurement (mVpeak) on each port
Monitor modes:
- Terminated/Repeater (75 Ohm unbalanced)
- Bridged (high impedance)
When E3 is selected:
Levels:
- Auto gain control for high, low and monitor jack; all unbalanced 1.2Vpeak to
36mVpeak, 34 dB dynamic range
Physical Layer line status indications for each LIM port:
- Loss of Signal (LOS)
- Loss of Frame (LOF)
- Alarm Indication Signal (AIS)
- Remote Defect Indication (RDI), formerly known as FERF
- Loss of Cell Delineation (LCD)
Physical Layer line vital counts for each LIM port:
- Code violations
- Out of frame (OOF) events
- Remote Defect Indication (RDI), formerly known as FERF
- Remote Error Indication (REI), formerly known as FEBE
- Bit Interleave Parity (BIP-8)
- Payload type mismatch
- Loss of Cell Delineation (LCD)
When T3 is selected:
Levels:
- Auto gain control for high, DSX-3, low, and monitor jack (min. = DSX –23 dB);
all unbalanced 1.2 V peak to 36 mV, 34 dB dynamic range
Physical Layer line status indications for each LIM port:
- Loss of Signal (LOS)
- Loss of Frame (LOF)
- Alarm Indication Signal (AIS)
- Remote Defect Indication (RDI), formerly known as FERF
- Loss of Cell Delineation (LCD) – directly mapped ATM mode
- PLCP OOF (out of frame) – PLCP ATM mode
- PLCP RAI – PLCP ATM mode
Physical Layer line vital counts for each LIM port:
- Code violations
- Frame bit error
- P1/P2 parity errors
- C-bit parity errors
- Remote Error Indication (REI), formerly known as FEBE
- Loss of Cell Delineation (LCD) – directly mapped ATM mode
- PLCP OOF (out of frame) – PLCP ATM mode
- PLCP Frame Bit Error – PLCP ATM mode
- PLCP BIP Error – PLCP ATM mode
- PLCP REI (remote error indication, formerly FEBE) – PLCP ATM mode
When E3 or T3 is selected:
ATM Layer at any supported rate for each LIM port (network and equipment):
- Full rate cell processing
- Auto-discovery and notification of up to 5120 virtual channels (VPI-VCI)
- ATM policing, traffic contract estimation and 1-point CDV
ATM Adaptation Layer (AAL) – frame mode:
- Auto-discovery and notification of up to 5120 AAL-2 Channels (VPI-VCI-CID)
and/or AAL-5 virtual channels (VPI-VCI), any mix of AAL-2 and AAL-5
19
- Concurrent real-time reassembly of the first 4000 bytes of multiple
AAL2 SSCS PDUs
- Count of total AAL-2 SSCS PDUs
- AAL-2 SSCS PDUs are reassembled to the SSSAR sub-layer
- Concurrent real-time reassembly of the first 4000 bytes of multiple AAL-5 SSCS
PDUs
- Count of total AAL-5 SSCS PDUs
- Reassembly of any mixture of up to 5120 AAL-2 and AAL-5 SSCS PDUs
- Reassembled AAL-5 SSCS PDUs with trailer CRC-32 errors
ATM and AAL statistics per VPI.VCI collected on multiple VCs
Statistics for Frame Relay, HDLC/SDLC, sync PPP for each LIM port:
- Total frames
- Bridged frames
- Bridged broadcast frames
- Bridged multicast frames
- Total octets
- Throughput (kbps)
- Aborted frames
- Short frames
- FCS errors
HDLC FCS can be set to 16-bit (default) or 32-bit with two variants of each
Frame Relay statistics per DLCI collected on 1024 VCs
Capture rate: Full line rate (full duplex)
Outputs (E3 and T3):
Termination:
75 Ohm
Levels:
ITU-T G.703
Clocking:
Recovered (loop)
Traffic Generation
Full rate ATM traffic generation
20
J6815B T1/E1 LIM,
J6816B E1/T1 LIM,
J6817B E1 LIM
(1.544 / 2.048 Mbps)
J6815B T1/E1 LIM
J6816B E1/T1 LIM
J6817B E1 LIM
21
General
All three LIMs handle ATM, Frame Relay, HDLC, SDLC and PPP. When analyzing ATM,
real-time (full rate) AAL-2 and AAL-5 reassembly is performed simultaneously on more
than 5120 virtual channels and the resulting frames are passed from the LIM to the
acquisition system for further analysis. Cell mode is also available.
ATM Policing can be performed on up to 1024 virtual circuits in frame mode or cell mode
simultaneously with other measurements.
The J6815B LIM has four Bantam connectors and two 8-pin RJ connectors, which can
be switched between RJ-48C and RJ-45 pin wiring via the configuration menu. This
module can be configured as a T1 (100 Ohm, 1.544 Mbps, default) or E1 (120 Ohm
2.048 Mbps) interface.
The J6816B LIM has DB-9 and 8-pin RJ connectors which can be switched between
RJ45 and RJ48C wiring via the configuration menu. Converter cables are available to
connect the DB9 to 120 Ohm Siemens 3-pin connectors. This module can be configured
as an E1 (120 Ohm, 2.048 Mbps, default) or T1 (100 Ohm, 1.544 Mbps) interface.
The J6817B LIM has 75 Ohm BNC connectors. This module can be configured only as an
E1 (2.048 Mbps) interface. Third-party vendors make conversion cables from this ISO
BNC connector to the ‘small Siemens BNC (1.6/5.6 mm)’, ‘large Siemens BNC’, ‘British
Telecom BNC’, etc.
Common to Inputs and Outputs:
Two input and output ports
When E1 is selected:
Interface termination:
- 120 Ohm balanced (J6815B, J6816B); 75 Ohm unbalanced (J6817B)
Line Code:
- ATM: HDB3
- Other WAN: HDB3, AMI
Framing:
- ITU-T G.704 alternate framing with or without CRC-4
- Fractional (ATM and Frame Relay), any multiple of 64 kbps channel
- Unframed at 2.048 Mbps
ATM Cell Mapping:
- Direct (ITU-T G.804)
ATM Cell Scrambling:
- Conforms to ITU-T I.432.1 (x43 + 1) and may be turned on or off
When T1 is selected (not applicable with J6817B):
Interface termination:
- 100 Ohm balanced
Line Code:
- ATM: B8ZS
- Other WAN: B8ZS, AMI
Framing:
- Extended Super Frame (ESF) with CRC-6
- D4 (Super Frame)
- Fractional (ATM and Frame Relay), any multiple of 56 kbps or 64 kbps channels
- Unframed 1.544 Mbps
ATM Cell Mapping:
- Direct (ITU-T G.804)
ATM Cell Scrambling:
- Conforms to ITU-T I.432.1 (x43 + 1) and may be turned on or off
22
Inputs:
Received pulse amplitude measurement (dBdsx)
When E1 is selected:
Monitor modes:
- Terminated (120 Ohm)
- Bridged (High Impedance)
- Monitor Jack: -20 dB and -30 dB
Physical Layer line vital counts for each LIM port:
- Code violations
- Loss of frame (LOF) events
- Frame bit error
- CRC-4 error
- Loss of Cell Delineation (LCD)
Physical Layer line status indications for each LIM port:
- Loss of Signal (LOS)
- Loss of Frame (LOF)
- Alarm Indication Signal (AIS)
- Remote Alarm Indication (RAI), formerly known as FERF
- Loss of Cell Delineation (LCD)
When T1 is selected:
Monitor modes:
- Terminated (100 Ohm)
- Bridged (High Impedance)
- Monitor Jack (20dB)
Interface types (and input sensitivities):
- DSX-1 (+6 dB to –10 dB )
- Network Interface (+6 dB to -36 dB )
Physical Layer line status indications for each LIM port:
- Loss of Signal (LOS)
- Loss of Frame (LOF)
- Alarm Indication Signal (AIS)
- Remote Alarm Indication (RAI), formerly known as FERF
- Loss of Cell Delineation (LCD)
Physical Layer line vital counts for each LIM port:
- Code violations
- Loss of frame (LOF) events
- Frame bit error
- ESF CRC-6 error
- 1s density
- Excess 0s
- Loss of Cell Delineation (LCD)
When E1 or T1 is selected:
ATM Layer at any supported rate for each LIM port (network and equipment):
- Full rate cell processing
- Auto-discovery and notification of up to 5120 virtual channels (VPI-VCI)
- ATM policing, traffic contract estimation and 1-point CDV
ATM Adaptation Layer (AAL) – frame mode:
- Auto-discovery and notification of up to 5120 AAL-2 Channels (VPI-VCI-CID)
and/or AAL-5 virtual channels (VPI-VCI), any mix of AAL-2 and AAL-5
- Concurrent real-time reassembly of the first 4000 bytes of multiple AAL-2 SSCS
PDUs
- Count of total AAL-2 SSCS PDUs
- AAL-2 SSCS PDUs are reassembled to the SSSAR sub-layer
- Concurrent real-time reassembly of the first 4000 bytes of multiple
- AAL-5 SSCS PDUs
23
- Count of total AAL-5 SSCS PDUs
- Reassembly of any mixture of up to 5120 AAL-2 and AAL-5 SSCS PDUs
- Reassembled AAL-5 SSCS PDUs with trailer CRC-32 errors
ATM and AAL statistics per VPI.VCI collected on multiple VCs
Statistics for Frame Relay, HDLC/SDLC, sync PPP for each LIM port:
- Utilization in percent
- Total frames
- Bridged frames
- Bridged broadcast frames
- Bridged multicast frames
- Total octets
- Throughput (kbps)
- Aborted frames
- Short frames
- FCS errors
HDLC FCS can be set to 16-bit (default) or 32-bit with two variants of each
Frame Relay statistics per DLCI collected on 1024 VCs (see details on page 15)
Capture rate: Full line rate (full duplex)
Outputs:
Termination:
- 120 Ohm when E1 is selected
- 100 Ohm when T1 is selected
Levels:
- ITU-T G.703
Clocking:
- Recovered (loop)
Traffic Generation:
- Full rate ATM, traffic generation
24
J6818A ATM25 LIM
(25.6 Mbps)
J6818B ATM25 LIM
The J6818B LIM interface handle ATM at 25.6 Mbps. Real-time (full rate) AAL-2 and
AAL-5 reassembly is performed simultaneously on more than 5120 virtual channels and
the resulting frames are passed from the LIM to the acquisition system for further
analysis. Cell mode is also available. Policing can be performed on up to 1024 virtual
circuits in frame mode or cell mode simultaneously with other measurements.
Common to Inputs and Outputs:
Main Specifications: ATM Forum af-phy-0040.000, ITU-T I.432.5
Ports: Two bi-directional, one toward the equipment and the other toward the network:
100 Ohm (for UTP-3 cable) and 120 Ohm (for UTP-5 cable)
Test configuration modes:
- Terminal (toward network or equipment – available in a future software
upgrade);
- Monitor (both directions for protocol analysis with repeater functionality in each
direction)
Connectors: RJ-45 (UTP)
Line Code: NRZI
Symbol Coding: 4B5B
Line Symbol Rate: 32 Mbaud
Cell Mapping: Symbolic direct (i.e. no framing)
Cell Scrambling: Conforms to af-phy-0040.000 (x10 + x7 + 1)
Inputs:
Physical Layer Alarms and Statistics:
- Invalid symbol
- Short cell
- Loss of signal (LOS)
- Loss of Timing Synchronization
- Timing synchronization frequency
ATM Layer at any supported rate for each LIM port (network and equipment):
- Full rate cell processing
- Auto-discovery and notification of up to 5120 virtual channels (VPI-VCI)
- ATM policing, traffic contract estimation and 1-point CDV
ATM Adaptation Layer (AAL) – frame mode:
- Auto-discovery and notification of up to 5120 AAL-2 Channels (VPI-VCI-CID)
and/or AAL-5 virtual channels (VPI-VCI), any mix of AAL-2 and AAL-5
25
- Concurrent real-time reassembly of the first 4000 bytes of multiple AAL-2 SSCS
PDUs
- Count of total AAL-2 SSCS PDUs
- AAL-2 SSCS PDUs are reassembled to the SSSAR sub-layer
- Concurrent real-time reassembly of the first 4000 bytes of multiple AAL-5 SSCS
PDUs
- Count of total AAL-5 SSCS PDUs
- Reassembly of any mixture of up to 5120 AAL-2 and AAL-5 SSCS PDUs
- Reassembled AAL-5 SSCS PDUs with trailer CRC-32 errors
ATM and AAL statistics per VPI.VCI collected on multiple VCs
Capture rate: Full line rate (full duplex)
Outputs:
Clocking:
- Recovered from line (loop), recovered from X8 8 kHz time synchronization
source
26
J6820B V-Series LIM
(up to 10Mbps)
J6820B V-Series LIM
Connection to supported interfaces is by means of separately supplied external
monitor/simulate cables, each specific to a particular V-series interface.
Monitor/Simulate Cables (J6757A)
-
option #001: V.35
option #002: RS-449/V.36
option #003: V.10/V.11 (for X.21)
option #004: RS-232C
option #005: EIA-530
Detail:
Bit rates:
- 2400 b/s to 8.192 Mbps on V.35, Sync or Sync NRZI;
- 2400 b/s to 10 Mbps on V.36/RS-449/422/423/EIA-530 and X.21, Sync or
Sync NRZI
- 300 b/s to 256 kbps on V.24/V.28/RS-232C
Lead status:
- RTS, CTS, DTR, DSR, and CD (V.24/V.28/RS-232C and V.35)
- CS, RS, RR, TR, and DM (V.10/V.11 and V.36/RS-449/422/423)
Statistics for Frame Relay, HDLC/SDLC, sync PPP for each LIM port:
- Utilization in percent
- Total frames
- Bridged frames
- Bridged broadcast frames
- Bridged multicast frames
- Total octets
- Throughput (kbps)
- Aborted frames
- Short frames
- FCS errors
HDLC FCS can be set to 16-bit (default) or 32-bit with two variants of each
Frame Relay statistics per DLCI collected on 1024 VCs
Capture rate: Full line rate (full duplex)
27
J6821A HSSI LIM
(up to 52Mbps)
J6821A HSSI LIM
Connection to the ports DCE and DTE of this LIM is accomplished through a 25-twistedpair cable with male HSSI connectors. Cable impedance is specified at 100 ohms (cable
not supplied by Agilent). The LIM supports Frame Relay, HDLC, SDLC and Sync PPP.
J6821A HSSI LIM supports only monitor mode. Bridged and Transmit modes are not
supported directly out of the LIM. Bridged mode provided by the J6756B HSSI Tap.
Bit Rates
- 56 kbps to 51.850 Mbps
- Example: DS3 (44.736 Mbps), SONET STS-1 (51.84 Mbps)
Lead Status
- Data: SD and RD
- Clock: ST, TT, and RT
- Control: CA and TA
- Test: LA, LB, LC, and TM
Statistics for Frame Relay, HDLC, SDLC, and Sync PPP for each LIM port
- Utilization in %
- Total Frames
- Bridged Frames
- Bridged Broadcast Frames
- Bridged Multicast Frames
- Total Octets
- Throughput (Kbps)
- Abort Frames
- Short Frames
- FCS Errors
HDLC FCS can be set to 16-bit (default) or 32-bit with two variants of each
Frame Relay statistics per DLCI collected on 1024 VCs
Capture Rate: Full Line Rate (full duplex)
28
J6824A Multi-port E1/T1 LIM
J6824A Multi-port E1/T1 LIM
The Multi-port E1/T1 LIM has 8 ports, which are configurable for E1 or T1 framing. Each
port on the LIM uses an 8-pin Modular connector (wired as RJ-48C), suitable for
balanced 100 Ohm T1, or 120 Ohm E1 interfacing, or unbalanced 75 Ohm E1 interfacing.
Three cable options are available, each providing a set of eight cables terminated with
RJ-48C connectors at one end for plugging into the LIM and option-specific male
connectors on the other end:
- option #001:
RJ-48C to pairs of male Bantam connectors
- option #002:
RJ-48C to pairs of 75 Ohm BNC connectors
- option #003:
RJ-48C to RJ-45 wired 8-pin Modular connectors (swaps
cable pairs between RJ-48C pins [1,2]/[4,5] to RJ45 pins [5,4]/[6,3],
respectively).
This LIM can provide analysis of IMA (Inverse Multiplexing for ATM) traffic, multi-port
ATM, Multi Link PPP, Multi-Link Frame Relay, Multi-Link HDLC, channelization with HDLC
(SS7, Frame Relay and ISDN) or TRAU 16K framing for the Agilent Signaling Analyzer,
and multi-port ISDN decodes. The IMA analysis requires, additionally, the presence of the
J6825A Inverse Multiplexing for ATM (IMA) and Multi-Link WAN Technologies software
product. Real-time (full rate) AAL 2 and AAL 5 reassembly is performed simultaneously
on more than 5120 virtual channels on aggregated IMA traffic or on each port of multiport ATM and the resulting frames passed from the LIM to the acquisition system for
further analysis. Cell mode is also available.
Network Analyzer application:
-
Multi-port ATM
Inverse Multiplexing for ATM (IMA)
Multi Link PPP,
Multi-Link Frame Relay
Multi-Link HDLC
Multi-port ISDN PRI layer 2 statistics and layer 3 decodes
Signaling Analyzer Real-Time (SART) application:
- Multi-port ATM
- Inverse Multiplexing for ATM (IMA)
- Multi-port channelized with HDLC (SS7, Frame Relay, and ISDN) or TRAU 16
Kbps framing
29
Common features of all 8 Ports:
Receiver Modes:
- Bridged (High Impedance), Terminated, Monitor Jack, and Thru/Bridged.
- Bridged, Terminated and Monitor Jack modes use two receivers per port
connected to pins [1,2] and [4,5] of the 8-pin Modular connector providing full
duplex 8 port monitoring (also see below for details on the J6826A and
J6827A monitor taps)
- Thru/Bridged monitoring of signals uses pairs of ports (1&2, 3&4, 5&6, 7&8).
Signals on port 1 and port 2 (pins [1,2] and [4,5]) are connected together to
pass through the customer data which is monitored by two receivers set to
Bridged (High Impedance) mode. Ports 3 and 4, ports 5 and 6, and ports 7 and
8 are similarly set to Thru/Bridged mode providing 4 port Thru/Bridged full
duplex monitoring.
Received pulse amplitude measurement (dBdsx), displayed in 2.5 dB ranges
Hardware is compliant with the following standards (NOTE: some standards do not apply
to current run modes or features, but apply to features added in the future):
- ANSI: T1.403-1995, T1.231-1993, T1.408
- AT&T: TR54016, TR62411
- ITU-T: G.703, G.704, G.706, G.736, G.775, G.823, G.932, I.431, I.432, O.151,
O.161
- ETSI: ETS 300 011, ETS 300 166, ETS 300 233, CTR12, CTR4
- Japanese: JTG.703, JTI.431, JJ-20.11 (CMI Coding Only)
When E1 is selected:
Interface termination:
- 120 Ohms balanced
- 75 Ohms unbalanced
Line Code:
- HDB3, AMI
Framing:
- ITU-T G.704 alternate framing with or without CRC-4
- Fractional, any multiple of 64 kbps channel
Receiver Modes:
- Terminated (120 Ohm or 75 Ohm)
- Bridged (High Impedance)
- Monitor Jack (-20 dB, -26dB, and -32 dB)
- 4 Port Thru/Bridged
When T1 is selected:
Interface termination:
- 100 Ohms balanced (no converter cable required)
Line Code:
B8ZS, AMI
Framing:
- Extended Super Frame (ESF) with CRC-6
- D4 (Super Frame)
- J1-ESF (calculates CDC-6 per JT-G.704)
- J1 D4 (uses Fs bit 12 as the RAI bit), WAN only
- Fractional, any multiple of 56 kbps or 64 kbps channels
Receiver Modes:
- Terminated (100 Ohm)
- Bridged (High Impedance)
- Monitor Jack (-20 dB)
- 4 Port Thru/Bridged
30
Measurements and Statistics:
When E1 is selected:
Physical Layer line status indications for each LIM port:
- Loss of Signal (LOS)
- Loss of Frame (LOF)
- Alarm Indication Signal (AIS)
- Remote Alarm Indication (RAI), formerly known as FERF
- Loss of Cell Delineation (LCD)
Physical Layer line vital counts for each LIM port:
- Code violations
- Loss of frame (LOF) events
- Frame bit error
- CRC-4 error
When T1 is selected:
Interface types (and input sensitivities):
- DSX-1 (+6 dB to –10 dB )
- Network Interface (+6 dB to -36 dB )
Physical Layer line status indications for each LIM port:
- Loss of Signal (LOS)
- Loss of Frame (LOF)
- Alarm Indication Signal (AIS)
- Remote Alarm Indication (RAI), formerly known as FERF
- Loss of Cell Delineation (LCD)
Physical Layer line vital counts for each LIM port:
- Code violations
- Loss of frame (LOF) events
- Frame bit error
- ESF CRC-6 error
- 1s density
When E1 or T1 Eight-port ATM (including IMA) is selected:
Convergence Sub-Layer Vital counts for each LIM port:
- Single-bit HEC Error
- Multi-bit HEC Error
- Loss of Cell Delineation (LCD)
ATM policing (not available with IMA), traffic contract estimation and 1-point CDV
Inverse Multiplexing for ATM (IMA) – requires J6825A software:
IMA sub-layer:
- Conforms to ATM Forum af-phy-0086.001/ITU-T I.761
- Number of links in an IMA Group: 2 to 8
- Number of simultaneous IMA Groups: 1 (currently)
- Fractional E1/T1 links supported
- Auto-configuration of IMA Group with manual over-ride
- ICP (IMA Control Protocol) Cell decode (per link)
- Auto-detection of change in configuration (excluding link test mode byte 15,
and test data bytes 16 and 17) with protocol analysis capture trigger
- Optional capture of all ICP cells or changing ICP cells in protocol capture (cell
mode)
IMA Vital Counts for each LIM port:
- All ICP Cells
- Changed ICP Cells
- Filler Cells
ATM Vital Counts per IMA Group (frame mode)
- Utilization
- Idle Cells
- Busy Cells
31
- Congestion Experienced
- CLP (low priority)
- Total Frames (frame mode)
- Bridged Frames (frame mode)
- Bridged Broadcast Frames (frame mode)
- Bridged Multicast Frames (frame mode)
- AALx Bad CRC-32 (frame mode)
- OAM F1 Cells (cell mode)
- OAM F3 Cells (cell mode)
- Resource Management Cells (cell mode)
ATM Layer for each direction (network or equipment) of the IMA Group:
- Full rate cell processing
- Auto-discovery and notification of up to 5120 virtual channels (VPI-VCI)
ATM Adaptation Layer (AAL) – frame mode:
- Auto-discovery and notification of up to 5120 AAL-2 Channels (VPI-VCI-CID)
and/or AAL-5 virtual channels (VPI-VCI), any mix of AAL-2 and AAL-5
- Concurrent real-time reassembly of the first 4000 bytes of multiple AAL-2 SSCS
PDUs
- Count of total AAL-2 SSCS PDUs
- AAL-2 SSCS PDUs are reassembled to the SSSAR sub-layer
- Concurrent real-time reassembly of the first 4000 bytes of multiple AAL-5 SSCS
PDUs
- Count of total AAL-5 SSCS PDUs
- Reassembly of any mixture of up to 5120 AAL-2 and AAL-5 SSCS PDUs
- Reassembled AAL-5 SSCS PDUs with trailer CRC-32 errors
ATM and AAL statistics per VPI.VCI collected on multiple VCs
Channelization:
- Simultaneous 8-port receive for both Network and Equipment sides
- Up to 1024 channels and up to 512 timeslots supported, aggregated across all
8 ports per side
- 8, 16, 32, 56, 64, Nx56, and Nx64 Kbps data rates per channel supported
- HDLC, SS7 and standard 16 K TRAU framing formats supported
- WAN Multi-port ISDN Measurements:
- Simultaneous decoding of layer 3 Q.931 call activity on up to 8 ISDN PRI DChannels
- Statistics for each port:
o Utilization
o Total Frames
o Bridged Frames
o Bridged Broadcast Frames
o Bridged Multicast Frames
o Total Octets
o Throughput (Kbps)
o Aborted Frames
o Short Frames
o FCS Errors
Transmitter Outputs (future emulation):
Termination:
Levels:
Clocks:
-
100 Ohms (balanced) via LIM RJ-48C connectors
120 Ohms (balanced) via LIM RJ-48C connectors
75 Ohms (unbalanced) via LIM RJ-48C to BNC connectors with Cable Option 2
ITU-T G.703
Recovered (loop), Internal, and External (input on one LIM port)
Currently, only monitor modes are available with this LIM
32
J6826A Eight-Port T1/E1 Balanced
Monitor Tap (up to 2 Mbps)
J6826A Eight-Port T1/E1 Balanced Monitor Tap
General
Eight full-duplex T1/E1 links are passed through the Monitor Tap using pairs of Modular
8-pin (RJ45 type) connectors (all eight pins of each connector are passed through). The
two data signals on connector pins [1,2] and [4,5] of each connector pair are wired to
attenuator resistors to provide a 20 dB Monitor Jack circuit that can be directly
connected to the J6824A Eight-Port T1/E1 LIM. Eight 3-foot RJ48C to RJ48C cables are
supplied with the Monitor Tap for connection to the J6824A LIM.
Specifications
-
Insertion Loss: <0.5 dB
Attenuation: -20.7 dB nominal for T1
Attenuation: -19.3 dB nominal for E1
Maximum data rate: 2.048 Mbps
J6827A Eight-Port E1 BNC
Monitor Tap (up to 2 Mbps)
General
Eight full-duplex E1 75 Ohm BNC ports are passed through the Monitor Tap using pairs
of pass through BNC to BNC connections, and each of these links are wired to attenuator
resistors to provide a 20 dB Monitor Jack circuit. The monitor tap contains impedance
conversion transformers to change these signals from unbalanced 75 Ohm to balanced
120 Ohm outputs for direct connection to the J6824A Eight-Port T1/E1 LIM. Eight 3-foot
RJ48C to RJ48C cables are supplied with the Monitor Tap for connection to the J6824A
LIM.
Specifications
- Insertion Loss: <0.7 dB
- Attenuation: -22.4 dB nominal
- Maximum data rate: 2.048 Mbps
33
J6828A Four-Port STM-1/OC-3
LIM Multiplexer
J6828A Four-Port STM-1/OC-3 LIM Multiplexer
General
This standalone multiplexer has four pairs of STM-1/OC-3 optical input ports. It is
designed to be used with the J6810B STM-4/OC-12/STM-1/OC-3 LIM operating in a
special mode to expand the latter’s analysis capability to both directions of four STM1/OC-3 ATM cell streams for use with the Agilent Signaling Analyzer Real-Time product.
This external LIM is powered from a 5V DC supply with AC input (provided).
The J6828A LIM can monitor 4 ports of ATM clear channel as well as demux with the
demux channelization license (J7836A) up to 336 T1/VT1.5/VC11 and 252
E1/VT2/VC12 ATM tributaries.
Inputs
Eight input ports grouped as four input port pairs
Connectors: SC-PC
Sensitivity:
- Min. -34 dBm
Loss of Signal Detect Level:
- Max. -36 dBm
- Min. –45 dBm
Framing:
- SDH: STM-1, ITU-T G.707
- SONET: STS-3c, GR-253
SDH / SONET Frame Scrambling (x7 + x6 + 1)
Receiver wavelength range: 1200/1600 nm
Optical power measurement for each LIM port:
- 0 dBm to -50 dBm dynamic range in steps of 0.1 dBm
- +/-0.5 dBm absolute accuracy at 1310 nm
Physical Layer line status indications for each LIM port (SDH / SONET):
- Loss of Signal (LOS)
- Loss of Frame (LOF)
- Loss of Pointer (LOP)
- Loss of Cell Delineation (LCD)
- MS-RDI / RDI-L (Line FERF)
- RDI / RDI-P (Path FERF)
- MS-AIS / AIS-L (Line AIS)
- AIS / AIS-P (Path AIS)
Physical Layer line vital counts for each LIM port (SDH / SONET):
- MS-RDI / RDI-L (Line FERF)
- RDI / RDI-P (Path FERF)
34
-
MS-AIS / AIS-L (Line AIS)
AIS / AIS-P (Path AIS)
MS-REI / REI-L (Line FEBE)
B1 BIP errors
Loss of Cell Delineation (LCD)
Functionality Available with J6828A/J6810B Combination
When the multiplexer is connected to the J6810B STM-4/OC-12/STM-1/OC-3 LIM, the
combined functionality available for each pair of STM-1/OC-3 ports (using the Signaling
Analyzer Real-Time product) is as follows (note that this functionality is not supported
with the J6810A LIM).
ATM Layer for each LIM port (network and equipment):
- Full rate cell processing
- Auto-discovery and notification of up to 5120* virtual channels (cell mode)
ATM Adaptation Layer (AAL) – frame mode:
- Auto-discovery and notification of up to 5120* AAL-2 Channels (VPI-VCI-CID)
and/or AAL-5 virtual channels (VPI-VCI), any mix of AAL-2 and AAL-5
- Concurrent real-time reassembly of the first 4000 bytes of multiple AAL-2 SSCS
PDUs (corner case: reassembly of long sequences of shortest possible CPS
packets is best effort)
- Count of total AAL-2 SSCS PDUs
- AAL-2 SSCS PDUs are reassembled to the SSSAR sub-layer
- Concurrent real-time reassembly of the first 4000 bytes of multiple AAL-5 SSCS
PDUs
- Count of total AAL-5 SSCS PDUs
- Reassembly of any user defined mixture of up to 5120* AAL-2 and AAL-5 SSCS
PDUs
- Reassembled AAL-5 SSCS PDUs with trailer CRC-32 errors
ATM and AAL statistics per VPI.VCI collected
Capture rate: Full rate, full duplex, on all ports
*aggregated over all four ports
35
J6830A 10BaseT, 10/100BaseTX LIM,
J6831A 10/100BaseFX LIM,
J6832A 1000BaseX LIM
J6830A 10BaseT, 10/100BaseTX LIM
J6831A 10/100BaseFX LIM
J6832A 1000BaseX LIM
36
General
The J6830A 10BaseT, 10/100BaseTX LIM handles Ethernet and Fast Ethernet over
unshielded twisted pair (UTP) cable. The J6831A 10/100BaseFX LIM handles Fast
Ethernet over multi-mode optical cable. The J6832 1000BaseX LIM accommodates a
pair of GBIC interface adapters for handling Gigabit Ethernet over short reach (SX), long
reach (LX) optical fiber, UTP-5 cable, or any combination of these; a pair of SX GBICs
(Short range Gigabit Interface Connectors) is included with this LIM. All LIMs are capable
of analysis and simulation. Other types of conforming GBIC may be supported (though
not supplied by Agilent), such as CX.
J6830A 10BaseT, 10/100BaseTX specific:
Connectors: two RJ-45 (UTP)
Auto-sensing 10/100 Ethernet ports for 10BaseT and 100BaseTX
A second RJ-45 port allows testing of full duplex Ethernet between two network
elements.
J6831A 10/100BaseFX specific:
Connectors: two duplex SC multi-mode 1300nm
J6832A 1000BaseX specific:
GBIC interfaces supported (any combination of the following):
J5491A SX GBICs (850 nm multi-mode) – included with the J6832A LIM
J5492A LX GBICs (1310 nm mono-mode)
J5495A T GBICs (UTP copper)
Other GBIC Interfaces supported:
Cisco WS-G5487 1000Base ZX GBIC (WS-G5487)
All LIMs:
Line and MAC statistics:
- bytes transmitted (total and per second)
- bytes received (total and per second)
- errors (total and per second)
- broadcasts (total and per second)
- multicasts (total and per second)
- frames transmitted (total and per second)
- frames received (total and per second)
- % transmitted
- % received
- local collisions
- remote collisions
- late collisions
- remote late collisions
- runts
- frames with bad FCS
- misaligned frames
Dribbles
Runts (good FCS)
Jabbers
Jabbers (good FCS)
Full rate, full duplex capture
37
J6772A Rack Mount Kit for Agilent Distributed Network Analyzer and High
Density Interfaces
J6772A Rack Mount Kit for Agilent Distributed Network Analyzer and High Density Interfaces. This
graphic shows a J6801B DNA and a J6828A Four-Port STM-1/OC-3 LIM Multiplexer mounted in the
J6772A Rack Mount Kit
General
The J6772A rack mount kit is a 19 inch, 1U platform that can hold:
- Single J6801A/B DNA
- Single J6801A/B DNA and a J6828A Four-Port STM-1/OC-3 LIM Multiplexer
- Single J6801A/B DNA, a J6824A Multi-port E1/T1 LIM and a J6826/7A
monitor tap
DNA Mechanical Specifications
Physical
Specifications
Power
Requirements
Size
(depth x width x height):
Weight
J6801B DNA
J6802B DNA MX
J6803B DNA PRO
307 x 259 x 61 mm
(12.1 x 10.1 x 2.4 inches)
406 x 440 x 88 mm
(14.6 x 17.3 x 3.5 inches)
311 x 300 x 114 mm
(12.25 x 11.75 x 4.5 inches)
2.3 kg (5.3 lb.)
7.3 kg (16.5 lb.)
4.5 kg (9.7 lb.)
100 - 240 V ~, 50 - 60 Hz, 2.0A
External
Option 1AC
100 - 240 V ~, 50 - 60 Hz, 2.5A
Option 1DC
í40 - í56 VDC, 1.4A Type (JA18)
100 - 240 V ~, 50 - 60 Hz, 2.5A
Operating
+5° to +40° C
(+41° to +104° F)
+5° to +40° C
(+41° to +104° F)
+5° to +40° C
(+41° to +104° F)
Non-operating
-25° to +60° C
(-13° to +140° F)
-25° to +60° C
(-13° to +140° F)
-25° to +60° C
(-13° to +140° F)
Operating
20% to 80%
Non-condensing
20% to 80%
Non-condensing
20% to 80%
Non-condensing
Non-operating
10% to 90%
Non-condensing
10% to 90%
Non-condensing
10% to 90%
Non-condensing
Operating
4,570m (15,000 ft)
4,570m (15,000 ft)
4,570m (15,000 ft)
Non-operating
12,200m (40,000 ft)
12,200m (40,000 ft)
12,200m (40,000 ft)
Temperature
Humidity
Altitude
Regulatory
Compliances
for all DNAs
EMC
Europe:
Canada:
Australia/New Zealand:
Low Voltage and EMC Directives (CE marked) IEC 61326-1
ICES-001 (marked)
AS/NZS 2064.1 (C-Tick marked)
Safety
IEC 61010-1 (CE marked)
UL 3111
CSA C22.2 No.1010.1 (CSA-C/US marked)
38
On-Line Information
For more information on DNA platform, please visit:
www.agilent.com/find/dna
For more information on Network Analyzer Software applications, please visit
www.agilent.com/find/networkanalyzer
For more information on Triple Play Analyzer, please visit:
www.agilent.com/find/tpa
For more information on Signaling Analyzer Software applications, please visit:
www.agilent.com/find/sart
Related Literature
Network Analysis and Troubleshooting Solutions
Distributed Network Analyzer Platform
5989-5455EN
Signaling Analyzer Technical Overview
5989-0347EN
Network Analyzer Technical Overview
5988-4231EN
Triple Play Analyzer Technical Overview
5989-5783EN
DNA Brochure
5989-3956EN
Signaling Analyzer Brochure
5989-4484EN
Mobile GSM GPRS UMTS R5 Poster
5989-4490EN
Protocol Communications Poster
5989-5245EN
Technology to quickly solve problems in today’s complex fixed and mobile networks
39
www.agilent.com
Agilent Technologies’ Test and Measurement Support, Services, and Assistance
Agilent Technologies aims to maximize the value you receive, while minimizing your risk
and problems. We strive to ensure that you get the test and measurement capabilities
you paid for and obtain the support you need. Our extensive support resources and
services can help you choose the right Agilent products for your applications and apply
them successfully. Every instrument and system we sell has a global warranty. Two
concepts underlie Agilent’s overall support policy: “Our Promise” and “Your
Advantage.”
Our Promise
Our Promise means your Agilent test and measurement equipment will meet its
advertised performance and functionality. When you are choosing new equipment, we
will help you with product information, including realistic performance specifications
and practical recommendations from experienced test engineers. When you receive
your new Agilent equipment, we can help verify that it works properly and help with
initial product operation.
Your Advantage
Your Advantage means that Agilent offers a wide range of additional expert test and
measurement services, which you can purchase according to your unique technical and
business needs. Solve problems efficiently and gain a competitive edge by contracting
with us for calibration, extra-cost upgrades, out-of-warranty repairs, and on-site
education and training, as well as design, system integration, project management, and
other professional engineering services. Experienced Agilent engineers and technicians
worldwide can help you maximize your productivity, optimize the return on investment
of your Agilent instruments and systems, and obtain dependable measurement
accuracy for the life of those products.
Agilent Email Updates
www.agilent.com/find/emailupdates
Get the latest information on the products and applications you select.
Agilent Direct
www.agilent.com/find/agilentdirect
Quickly choose and use your test equipment solutions with confidence.
Agilent Open
www.agilent.com/find/open
Agilent Open simplifies the process of connecting and programming test systems to
help engineers design, validate and manufacture electronic products. Agilent offers
open connectivity for a broad range of system-ready instruments, open industry
software, PC-standard I/O and global support, which are combined to more easily
integrate test system development.
For more information on Agilent
Technologies’
products, applications or services,
please contact your local Agilent office.
The complete list is available at:
www.agilent.com/find/contactus
Phone or Fax
United States:
(tel) 800 829 4444
(fax) 800 829 4433
Canada:
(tel) 877 894 4414
(fax) 800 746 4866
China:
(tel) 800 810 0189
(fax) 800 820 2816
Europe:
(tel) 31 20 547 2111
Japan:
(tel) (81) 426 56 7832
(fax) (81) 426 56 7840
Korea:
(tel) (080) 769 0800
(fax) (080) 769 0900
Latin America:
(tel) (305) 269 7500
Taiwan:
(tel) 0800 047 866
(fax) 0800 286 331
Other Asia Pacific Countries:
(tel) (65) 6375 8100
(fax) (65) 6755 0042
Email: [email protected]
Contacts revised: 05/27/05
www.agilent.com/find/dna
www.agilent.com/find/networkanalyzer
www.agilent.com/find/tpa
www.agilent.com/find/sart
Product specifications and descriptions in this
document subject to change without notice.
© Agilent Technologies, Inc. 2006
Printed in USA, 6 November 2006
5988-4176EN
5988-4176EN
40
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement