Manual 11656103

Manual 11656103
AFTERCARE INSTRUCTIONS
Your fitting has a high quality finish and should be treated with care to preserve the
visible surfaces.
All surface finishes will wear if not cleaned correctly, the only safe way to clean your
mixer is to wipe with a soft damp cloth. Stains can be removed using washing up
liquid. All bath cleaning powders and liquids will damage the surface of your fitting,
even the non-scratch cleaners.
GUARANTEE
All products are manufactured to the highest standards and a 5 year guarantee
covers any defect in manufacture.
As gold and special effect finishes are softer than chromium plate,
Special care must be taken when cleaning, a 3 year guarantee covers these
finishes.
NOTE: The 5-year guarantee on the cartridge is invalidated if damaged by any
waterborne debris.
In the interests of continuous product development we reserve the right to alter
specification as necessary
PRODUCT CODE: J 1HBF C / G / COM / SC
Java One Hole
Bath Filler
PRODUCT IDENTIFICATION CODE LASER ETCHED ON PRODUCT
Installer please fill in code here
.
TELEPHONE HELPLINE! +44 (0)844 701 6273
Bristan Group Limited
Birch Coppice Business Park
Dordon
Tamworth
Staffordshire
B78 1SG
UK
A Masco Company
Website: www.bristan.com
Telephone:+44 (0) 844 701 6274
Facsimile: +44 (0) 844 701 6275
Email: [email protected]
(FI J 1HBF C)
(Rev.D3)
Fitting Instructions
Please keep these instructions for future reference and request of
replacement part
WATER PRESSURE
INSTALLATION
This mixer is suitable for use at all supply pressures from 0.2 bar to 8 bar.
However for optimum use both the hot and cold supplies should be reasonably
balanced. If the fitting is installed at low pressure (tank fed), then the minimum
distance from the outlet of the nozzle to the underside of the cold tank should be
2 metres to ensure adequate performance.
1. Identify all components and check for completeness, particularly before
arranging fitting.
2. Fit the mixer body to the bath using the 'C' plate fixing kit. The full rubber
washer (1) goes between the fitting and the bath, and the 'C' shaped rubber
(2) and metal washers (3) on the underside of the bath, to be secured by the
nut (4) and threaded rod (5).
3. Fit the tail pipes (6) to the fitting and connect the hot and cold supplies.
4. Fully open the mixer in the mid position, letting it run for a few minutes to
check all joints and connections for leaks.
5. See over the page for aftercare instructions.
This mixer should be installed in compliance with Water Regulations. Where the
supplies are unbalanced, i.e. hot water from the cylinder tank / cold from the
mains, approved check valves must be fitted in the supply pipes. For further
details contact your Local Water Authority.
MAINTENANCE
If the fitting begins to drip:
1. Isolate water supplies.
2. Prise out handle cap, loosen grub screw and lift off the handle.
3. Unscrew the shroud and brass retaining plate and lift out the cartridge
complete with seal.
4. Clean or replace cartridge, clean and grease seal and refit.
'C' PLATE
FIXING KIT
1
2
3
4
5
6
Please Note: that there are locating pins on the bottom of the cartridge that fit in
holes inside the tap, to ensure it is fitted the right way round.
5. Refit the handle and tighten the grub screw. Replace the handle cap.
6. If problem persists contact our helpline quoting the product code.
Please Note: In the unlikely event you find a part missing please contact our
Customer Service Helpline on 0844 701 6273 or email [email protected] for
immediate despatch of part.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement