Macrovision Corporation | Dual Screen Portable DVD Player | Owner`s manual | Macrovision Corporation Dual Screen Portable DVD Player Owner`s manual

TM
PVS10921
Portable DVD Player with LCD Display
R
D I G I TAL
PHOTO
OWNER'S MANUAL
1
SAFETY PRECAUTIONS
The lightning flash with an arrowhead symbol, within
the equilateral triangle, is intended to alert the user to
the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient
magnitude to cause an electric shock.
CAUTION
WARNING: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
DANGER OF EXPLOSION IF BATTERY
IS INCORRECTLY REPLACED. REPLACE
ONLY WITH THE SAME OR EQUIVALENT
TYPE.
The exclamation point within the equilateral triangle
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions
in this owner manual.
* SEE BOTTOM OF UNIT FOR GRAPHIC SYMBOLS *
CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
AVOID EXPOSURE TO BEAM
This
product
contains a low
power laser device.
The symbol for Class II
(Double lnsulation)
On Placement
• Do not use the unit in places which are extremely hot, cold, dusty, or humid.
• Place the unit on a flat and even surface.
• Do not restrict the air flow of this unit by placing it somewhere poor air flow, by covering it with a cloth, or by
placing it on bedding or carpeting.
FCC Information
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesirable
operation.
“Warnings: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the equipment.”
On Safety
• When connecting or disconnecting the AC cord, grip the plug and not the cord itself. Pulling the cord may
damage it and create a hazard.
• When you are not going to use the unit for a long period of time, disconnect the AC power cord.
On Condensation
• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the
unit. When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1
to 2 hours before turning the power on, or gradually heat the room and let the unit dry before use.
Rating Plate Location
• The rating plate is located on the bottom of unit.
WARNING:
• Should any problems occur, disconnect the AC power cord and refer servicing to a qualified technician.
Notes on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, rent copyrighted material
without permission.
Apparatus Claims of U.S. Patent Nos. 4,631,603; 4,577,216; 4,819,098 and 4,907,093 licensed for limited
viewing uses only.
DVD video discs are copy protected, and any recordings made from these discs will be distorted. This product
incorporates copyright protection technology that is protected by method claims of certain U.S. patents and
other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and
other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
E - 1
P1-4_v6.PMD
1
10/18/2005, 11:54 AM
IMPORTANT SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
Read Instructions - All the safety and operating instructions should be read before you use the unit
Keep the Instructions - The safety and operating instructions should be kept for future reference.
Pay Attention to Warnings - All warnings on the unit and in this user's manual should be followed.
Follow Instructions - All operating and use instructions should be followed.
Water and Moisture - This unit should not be used near water or liquids- for example, near a bathtub,
sink, wet basement, swimming pool, lake or ocean, beach, or similar places where there is a chance
that the unit may come into contact with water or liquid.
6. Carts and Stands - This unit should only be used with a cart or stand that is
recommended by the manufacturer.
6A. If this unit is placed on a cart, it should be moved with care. Quick stops, excessive
force, and uneven surfaces may cause the cart to overturn.
7. Wall or Ceiling Mounting - This unit is not designed to be mounted to a wall or ceiling.
8. Ventilation - This unit should be situated so that its location or position does not
interfere with its proper ventilation. For example, the unit should not be used on a bed, sofa, rug, or
similar soft surface which may block the ventilation openings. The unit should also not be built-in to
a book case or cabinet, as that may impede the flow of air through the ventilation openings.
9. Heat - This unit should be situated away from heat sources such as radiators, heat registers, stoves,
or other items (including amplifiers) that produce heat.
10. Power Sources - The appliance should be connected to a power supply only of the type described in
these instructions or as marked on the unit.
11. Grounding or Polarization - Do not try to defeat the grounding or polarization safeguards built into
the unit.
12. Power-Cord Protection - Power-supply cords should be routed so that they are not likely to be walked
on or pinched by items placed on or against them. Pay particular attention to cords at plugs, power
outlets, and the point where the cord exits the unit.
13. Cleaning - This unit should be cleaned only as recommended by the manufacturer.
14. Nonuse Periods - The power cord should be unplugged from the wall outlet when the unit will not be
used for a long period of time.
15. Drops and Spills - Care should be taken so that objects do not fall on this unit, and liquids are not spilled
on or in the unit through openings in its enclosure.
16. Damage Requiring Service - This unit should be serviced by qualified personnel when:
A. The power-supply cord or the plug has been damaged; or
B. Objects have fallen on, or liquid has been spilled into the unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or there is a noticeable change in its performance; or
E. The unit has been dropped, and / or the enclosure damaged.
17. Servicing - The user should not attempt to service this unit beyond what is described in these
instructions. All other servicing should be referred to qualified personnel.
E - 2
P1-4_v6.PMD
2
10/18/2005, 11:54 AM
TABLE OF CONTENTS
Repeat Playback ................................... 18
Safety Precautions ..................................1
Important Safety Instruction ................. 2
Table Of Contents .................................... 3
Disc Formats ............................................ 4
Accessories ............................................... 5
Remote Control ........................................ 5
Control Reference Guide .................... 6-7
Power Supply ................................... 8-10
Repeating a title/chapter (DVD) ............................ 18
Repeating a single track/whole disc (CD) ........... 18
Repeating a specific section (DVD/CD) .............. 18
Playing MP3/Digital Picture Files ........... 19
Playing a MP3 / Picture file disc ........................ 19
Customizing the Function
Settings .............................................. 20-21
LANGUAGE setting .................................................. 20
Using the AC adaptor ...................................... 8
VIDEO setting .......................................................... 20
Using the rechargeable battery Pack ............... 9-10
RATING setting ....................................................... 21
Turning on the unit .............................................. 10
Language Code List for
Disc Language ...................................... 22
Maintenance .......................................... 23
Connecting other Equipment ......... 11-12
Connecting your TV .............................................11
Connecting to a stereo receiver ..........................11
Cleaning Disc .......................................................... 23
Using headphone/earphones .............................. 12
Cleaning the Unit ................................................... 23
Adjusting the Sound ............................ 12
Playing a Disc ................................... 13-15
Important Note ....................................................... 23
Trouble Shooting Guide ...................... 24
Playing Disc .......................................................... 13
Pausing playback (still mode) ............................... 13
Stopping playback ................................................. 13
To skip to a different track ...................................... 13
Fast Foward/Fast Reverse ..................................... 14
Skip (Forward/Reverse) .......................................... 14
Audio selection ....................................................... 14
Subtitle selection .................................................... 15
Angle selection ..................................................... 15
Special Functions ................................. 16
Display function .......... ........................................ 16
GOTO function ........ .............................................. 16
Locating a specific title ......................................... 16
Locating a specific chapter/track .......................... 16
Locating a specific time ......................................... 16
CD / DVD programmable memory ....... 17
DVD programmable memory ................................. 17
CD programmable memory .................................. 17
E - 3
P1-4_v6.PMD
3
10/18/2005, 11:54 AM
DISC FORMATS
The unit can playback.
DVDs
[8cm/12cm disc]
Compatible
Audio CDs
[8cm/12cm disc]
Region Management Information
Region Management Information: This unit is designed and manufactured to respond to the Region Management
Information that is encoded on DVDs. If the Region number printed on the DVD does not correspond to the
Region number of this unit, it cannot play that disc.
The region number of this unit is 1.
1
Disc Function or Operation that is Not Available
When the
symbol appears on the screen, it indicates that the function or operation you have selected is
not available at that time. This occurs because the DVD manufacturer sets the specific functions of DVDs.
Certain functions may not be available on some DVDs. For more information, refer to the documentation
provided with the DVD.
Icons Used on DVDs
Sample lcons
2
2
1. English
2. French
Language selections for audio
1. English
2. French
Language selections for subtitles
Screen aspect ratio
Multiple camera angles
2
Region code indicator
Notes:
• This Unit supports 2-channel (L/R) audio and 5.1ch (Multi-channel) MPEG Audio 1/2. It does not support 7.1
channel MPEG Audio Version 2.0.
• When playing back a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic
images will not be shown.
Title, Chapter and Tracks
• DVDs are divided into “titles” and “chapters”. If the
DVD has more than one movie on it, each movieis a
separate “title”. Titles are divided into smaller sections
called chapters.
T
Chapter 1
Chapter 2
Chapter 3
Chapter 1
Chapter 2
Track 4
Track 5
• Audio CDs are divided into “tracks”. Each song is
usually one track.
Track 1
Track 2
Track 3
Note :
• Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on them,
but some do not.
Notes on Unauthorized Discs
You may not be able to play some DVDs on this unit, particularly if they were purchased from outside your
geographic area (refer to Region Management Information above), or made for business purposes.
E - 4
P1-4_v6.PMD
4
10/18/2005, 11:54 AM
ACCESSORIES
Please locate the included accessories:
Remote control (with battery) ........................................................................................... x 1
AC adaptor .......................................................................................................................... x 1
AC power cord ................................................................................................................... x 1
Audio/V ideo cable .............................................................................................................. x 1
Earphones ........................................................................................................................... x 1
Rechargeable battery pack ................................................................................................ x 1
REMOTE CONTROL
Using the Remote Control
• Point the Remote Control at the REMOTE SENSOR located on the unit.
• When using this unit in very bright light, the infrared REMOTE CONTROL SENSOR may not work properly.
• The recommended effective distance for using the remote control is about 16 feet (5 meters).
Remove the plastic sheet before using the Remote Control.
TO CHANGE THE REMOTE CONTROL BATTERY
1. Open the battery door.
2. Insert one CR2025 (3V) size battery.
BATTERY REPLACEMENT
When the battery becomes weak, the operating distance of the Remote Control will be greatly reduced
and you will need to replace the battery.
Notes:
• If the Remote Control is not going to be used for a long time, remove the battery.
WARNING:
•Do not dispose of the battery in a fire or it may leak and/or explode.
E - 5
P5-8R_v6.PMD
5
10/18/2005, 11:59 AM
CONTROL REFERENCE GUIDE
Remote Control
1
2
3
4
5
6
TV MODE
STOP
PLAY
PREV
PAUSE
SEARCH
MEM
ANGLE
M
8
15
GOTO
14
NEXT
13
12
11
10
DISPLAY
AUDIO
ENTER
2
7
MENU
3
SUBTITLE/RETURN
4
5
6
7
8
9
9
0
SETUP
A-B
DISC
REPEAT
REPEAT A-B / DISC buttons
Perform point-to-point repeat playback on a DVD or
CD.
Repeat a DVD chapter or title.
Repeat a CD track or the entire disc.
/ RETURN button
9) SUBTITLE
Select one of the subtitle languages programmed on
a DVD (if available).
Return to the normal operation after using the SETUP
menu of a DVD.
10)AUDIO button
Select one of the audio sound tracks on a DVD (if
more than one is available) or select the audio
output mode on a CD.
11)ANGLE button
Switch between multiple camera angles when the
DVD you are playing has been programmed with
multiple camera angles.
12)DISPLAY button
Show status information on the screen.
NEXT button
13)
Move forward through titles, chapters or tracks on a
disc.
14)GOTO button
Skip directly to a location on a DVD.
15)MENU button
Enter and exit the main DVD menu.
1) TV MODE button
In stop mode, select whether to output the video
signal in PAL or NTSC. When the TV shows “AUTO”
this means the output signal depends on the DVD If
the TV shows “PAL” or “NTSC” the signal is fixed to
either “PAL” or “NTSC”.
2) STOP button
Stop playing a disc.
PLAY button
Press to start or resume playback a disc.
PAUSE button
Press once to pause playback. Press subsequently
to advance the DVD one frame at a time.
PREV button
3)
Move back through titles, chapters or tracks on a disc.
/
SEARCH buttons
4)
SEARCH: Fast reverse playback.
SEARCH: Fast forward playback.
5) MEMORY button
When the STOP button has been pressed, this feature
is used to enter the number of a chapter or track which
you wish to save in memory.
6) Cursor ( , , , ) buttons
Use to move between selections on a menu screen
and adjust certain settings.
ENTER button
Confirm selections on a menu screen.
7) Number (0 - 9) buttons
Use when creating programmes, and entering a
password. Also use to select a CD track directly.
8) SETUP button
When a DVD is stopped, brings up the unit's SETUP
menu.
... ..
E - 6
P5-8R_v6.PMD
6
10/18/2005, 11:59 AM
CONTROL REFERENCE GUIDE
Unit
14
12
11
13
DC IN 9V
CAR PLUG 12V
10
1
9
1)
8 7
6)
- VOLUME + button
Adjusts the volume up (+) and down (-).
MENU button
Open and close DVD's menu.
2)
3)
4)
5)
7)
8)
PAUSE button
Press to pause playback of disc. Each time you
subsequently press the PAUSE button the picture
advances one frame at a time. Press the PLAY
button to resume playback at normal speed.
AUDIO & VIDEO OUT jacks
Headphone jacks
Cursor ( ,
, , ) button
Use to move between selections on a menu screen
and adjust certain settings.
ENTER button
Confirm selections on a menu screen.
PREV button
Press
PREV button to go back to previous chapters
/tracks. Press and hold
PREV button to begin fast
scan.
NEXT button
Press
NEXT button to advance chapters / tracks.
Press and hold
NEXT button to begin fast forward
scan.
9)
10)
11)
12)
13)
14)
4
6
3 2
5
STOP button
Stop playing a disc.
PLAY button
Press to start or resume playback a disc.
BATTERY LOW indicator
Power ON indicator
When the Power ON/OFF switch is in the ON position,
the light will illuminate.
Remote sensor
Receives the remote control unit signals
Disc Door
Close door by gently pushing down.
DC IN 9V jack
POWER ON/OFF switch
SCREEN switch
Wide screen
Normal screen
button
Adjust the relative lightness or darkness of the colour.
E - 7
P5-8R_v6.PMD
7
10/18/2005, 11:59 AM
POWER SUPPLY
A. Using the AC adaptor
This AC adaptor operates on AC power between 110V and 240V, but
• In the USA and Canada, the AC power supply cord must be connected to a 120V AC power supply only.
• When connecting to an AC supply outside of the USA and Canada, use a plug adaptor to suit the AC outlet
configuration.
Power indicator
AC adaptor
AC power cord
2
To AC adaptor
1
To DC IN 9V jack
3
To AC outlet
DC IN 9V
CAR PLUG 12 V
Left side of unit
Caution:
• The included AC power supply cord and AC adaptor are for use with this unit only. Do not use them with other
equipment.
• If you are not going to be use the unit for a long time, disconnect the power cord from the outlet.
• Whenever the AC power supply cord and AC adaptor are plugged in to a power outlet, electricity is running
through the unit, even when the power switch is turned off.
E - 8
P5-8R_v6.PMD
8
10/18/2005, 11:59 AM
POWER SUPPLY
C. Using the rechargeable battery pack
• Charge the battery for at least 4-5 hours before using
it for the first time. The charging light will go out when the
battery is fully charged.
When recharging the battery, disconnect it from the unit.
RECHARGEABLE
BATTERY
PACK
PO WER
POWER indicator
FOR BATTERY
CHARGE
Use the supplied AC adaptor.
Never dispose of in fire or heat up.
Do not use in high temperature or near heat sources.
Never connect the positive and negative poles with metal.
Do not open the cover, refer servicing only to qualified ser vice personnel.
CHARGING indicator
BAT T.
DC IN 9V
C HARG ING
OUT
1 To "DC IN 9V" jack
3
AC ADAPTOR
(DC
9V 2.2A)
2
To wall outlet
To AC ADAPTOR
Caution:
• The included AC power supply cord and AC adaptor are for use with this unit only. Do not use them with other
equipment.
• To prevent electrical shock, match wide blade of plug to wide slot on electrical outlet and fully insert.
• If you are not going to use the unit for a long time, disconnect the AC power supply cord from the AC outlet.
• Recharging is complete when charging indicator goes out. Unplug the AC power supply cord from the AC
adaptor, then unplug the rechargeable battery pack.
• Do not short-circuit the terminals on the battery.
To attach rechargeable battery pack, slide it in to the corresponding positions on the back of the unit.
RECHARGEABLE BATTERY PACK
Rear of unit
Left side of unit
DIGITAL
OUT
DC IN 9V
CAR PLUG 12V
5
To "DC IN 9V" jack
4
ATTACH
RECHARGEABLE
BATTERY PACK
TO UNIT
RECHARGEABLE
BATTERY PACK
E - 9
P9-12.PMD
9
10/18/2005, 12:01 PM
POWER SUPPLY
Disconnecting rechargeable Battery Pack from the unit.
Push the button to disconnect the
RECHARGEABLE BATTERY PACK
FOR BATTERY
CHARGE
Use the suppli ed AC adaptor.
Never dispose of in fire or heat up.
Do not use in hi gh temperature or near heat sources.
Never c onnect t he pos iti ve and negativ e poles with metal.
Do not open the cover, ref er servicing only to qual ifi ed servi ce personnel.
BAT T.
DC IN 9V
RECHARGEABLE BATTERY PACK
OU T
PUSH DOWN KNOB AND SLIDE
BATTERY PACK TO RELEASE.
bottom of the unit
•
•
•
•
•
•
•
•
•
•
•
Important Notes:
The battery can only be recharged using the AC adaptor. The battery cannot be recharged using the 12V car
power adaptor.
During playback, if the rechargeable battery is low, the BATTERY LOW indicator on the front will turn red and
blink. When this occurs, you should recharge the battery.
Use only the supplied AC ADAPTOR and BATTERY CHARGER to rechargeable battery pack.
Detach rechargeable battery pack when not in use. (Even if the unit is off, it still uses some power. This can
completely discharge the rechargeable battery and cause it to malfunction.)
When the battery power is low, the unit will stop playing. Rechargeable battery pack when you are ready
to use it again.
If the rechargeable battery pack is not to be used for a long period of time, discharge it and store it in a place
that is cool, dry and dark.
While using the rechargeable battery pack, the air temperature should be between 41°F (5°C) to 95°F (35°C).
To get the longest battery life, charge the battery at indoor temperatures.
Never dispose of the rechargeable battery pack in fire or water.
Never heat up the rechargeable battery pack.
Do not open the rechargeable battery pack, refer servicing to qualified personnel.
Turning on the unit
1. Slide the POWER ON/OFF switch to the "ON" position.
• The DVD logo (start-up picture) will appear on the screen.
E - 10
P9-12.PMD
10
10/18/2005, 12:01 PM
CONNECTING OTHER EQUIPMENT
A. Connecting the unit to a TV
• If your TV has Audio/Video inputs, you can connect the unit to your TV using the included Audio/Video cable.
Right side of unit
AUDIO
VIDEO
OUT
OUT
TV
To AV OUT
Jacks
(Yellow)
VIDEO
IN
(Red)
AUDIO/VIDEO
CABLE
(included)
AUDIO/VIDEO
CABLE
AUDIO
IN
(White)
Watching a DVD on your TV
1. Turn on the unit.
2. Turn on the TV and follow the instructions provided with it to play the DVD.
Note: Please use the correct Audio/Video cable.
B. Connecting to an amplifier or stereo receiver
This unit can play Dolby Digital, but only in two channels.
Analog connection
Right side of unit
AUDIO
VIDEO
OUT
OUT
(No need to connect the Yellow video plug)
Amplifier or stereo receiver
(Red)
AUDIO/VIDEO
CABLE
(included)
AUDIO
IN
AUDIO/VIDEO (White)
CABLE
Listening to another audio equipment
1. Turn on the Unit.
2. Turn on your audio equipment and follow the instructions included with it to select the AUDIO IN function.
Notes:
• You may experience interference if the radio tuner function is selected while the television is working.
• Make sure to use the correct Audio/Video cable, connecting the plugs incorrectly may cause a weak signal.
• If you have a stereo VCR, make sure you set it to stereo mode.
• Due to copyright protection, DVD movies cannot be copied. If you copy a DVD movie onto a videotape, the
resulting copy will be unclear, with poor sound quality. This is NOT caused by a defective DVD system.
E - 11
P9-12.PMD
11
(continued on next page)
10/18/2005, 12:01 PM
CONNECTING OTHER EQUIPMENT
Using Headphones/Earphones
• Turn down the volume before connecting, and
then adjust the volume level.
• When headphones/earphones are connected,
no sound will be output from the unit's speakers.
Right side of unit
AUDIO
VIDEO
OUT
OUT
Caution:
• Avoid listening to sound at levels which may be
harmful to your ears.
Note:
• When headphones are connected to the unit,
the speakers are automatically disabled.
HEADPHONES / EARPHONES
(3.5mm diameter plug)
ADJUSTING THE SOUND
Dolby Digital (for DVD)
Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can
reproduce from one to 5.1 discrete channels of excellent quality audio.
The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for two-channel
listening. An additional Dolby Digital decoder is required for reproduction of the discrete multi-channel
soundtracks available on many DVDs.
Manufactured under license from Dolby Laboratories.
'Dolby' and the double-D symbol are trademarks of Dolby Laboratories.
E - 12
P9-12.PMD
12
10/18/2005, 12:01 PM
DVD
CD
PLAYING A DISC
Basic playback
This owner’s manual explains the basic instructions for operating this unit. Some DVDs are
produced in a manner that allows specific or limited operation during playback. Therefore, this
unit may not respond to all operating commands. THIS IS NOT A DEFECT. Please refer to the
instructions accompanying the specific DVD in question for more information about the options
available on that DVD.
“
” may appear on the screen during operation. The “
” symbol means that the desired
operation is not permitted by the unit or disc.
Playing a Disc
1. Slide the POWER ON/OFF switch on the left side of the unit to the ON position.
2. Push the OPEN switch to open the disc door.
3. Hold the disc by its sides and carefully place it onto the spindle with the label side facing up; press the disc down
until you hear a “click”.
4. Push the door to close.
It takes a short while for your unit to load the disc. After loading, the unit will automatically either bring you to the
main menu of the DVD, or start playing the DVD.
5. If the unit does not automatically start playing the DVD, press the PLAY button from the main menu.
Pausing playback (still mode)
Press the II PAUSE button. To resume normal playback, press the
PLAY button.
Each time you press the II PAUSE button, the picture advances one frame.
Stopping playback
Press the ■ STOP button at the location where you want to interrupt playback. To resume playback at the position
where the disc was stopped, press the PLAY button.
If you press the ■ STOP button twice, the unit’s memory will be cleared and pressing the PLAY button will reset
the disc to the beginning.
Skipping to a different track
• Press the
PREV button to skip to the start of the current track.
NEXT button to skip to the next track.
• Press the
• For audio CDs, use the number buttons on the remote control to jump immediately to the desired track number.
E - 13
P13_v6.pmd
13
(continued on next page)
10/18/2005, 12:06 PM
DVD
CD
PLAYING A DISC
Basic playback
Fast Forward/Fast Reverse
1. Press the SEARCH
or
SEARCH button of the remote unit when a disc is playing.
• The disc begins a fast scan at two times normal (x2) speed.
• Four speeds are available. Each time the SEARCH
or
SEARCH button is pressed, the speed of the fast
scan changes.
Note :
You also can press and hold
2. Press the
/
(PREV/NEXT) buttons on unit repeatedly to select different fast scan speeds.
PLAY button when you reach the desired point to resume playback at normal speed.
SKIP (Forward / Reverse)
While you are playing a disc, press the
NEXT button to move to the beginning of the next chapter or track. Press
the
PREV button to move to the previous chapter or track and playback will automatically begin.
Audio selection
DVD
On some discs, the sound is recorded in two or more formats. Follow the directions below to select the type of
playback.
1. While a disc is playing, press the AUDIO button to show the current audio format number.
2. Press the AUDIO button repeatedly to select the desired audio format.
2/4
D 6 Ch Eng
Notes :
• If only one audio format is recorded, the number does not change.
• About two seconds after a selection is made, playback continues in the new audio format.
E - 14
P14-18.pmd
14
(continued on next page)
10/18/2005, 12:07 PM
DVD
PLAYING A DISC
Basic playback
Subtitle selection
1. While a DVD is playing, press the SUBTITLE / RETURN button to display the current language setting, as shown
in the diagram.
2. Press the SUBTITLE / RETURN button repeatedly to select the desired subtitle language.
1/3 Eng
Notes :
• If only one language is recorded, the language does not change.
• About two seconds after selecting the subtitle language, playback continues with the new subtitle you selected.
• The number of languages recorded differs depending on the disc.
• If no button is pressed within a few seconds, playback continues without changing the current subtitle.
• This function can only be used for discs on which subtitles have been recorded in multiple languages.
• On some DVDs, subtitles are activated from the main menu of the DVD. Press the MENU button to activate the
main menu.
Angle selection
Some DVDs contain scenes which have been shot from a number of different angles. For these discs, the same
scene can be viewed from each of these different angles.
1. While you are playing a DVD with different angles recorded, press the ANGLE button to view the number of
current angles available.
2. Press the ANGLE button repeatedly to change the scene to the next recorded angle.
• After approx. two seconds, playback will continue from the new angle you selected.
• If no button is pressed within 10 seconds, playback continues without changing the current angle.
Sequence of angle shots (Example)
1/2
Angle
1/3
BitRate
Angle
2/3
BitRate
Angle
3/3
BitRate
Notes:
• This function can only be used for discs on which scenes shot from multiple angles have been recorded.
• If only one angle is recorded, “
1/1
” is displayed.
E - 15
P14-18.pmd
15
10/18/2005, 12:07 PM
DVD
CD
SPECIAL FUNCTIONS
Basic playback
DISPLAY function
DVD
Using DISPLAY, you can check the current settings of the following items: ANGLE, AUDIO and SUBTITLE.
• While the disc is playing, press the DISPLAY button of the remote unit to display the screen as shown in diagram.
Elapsed time: Elapsed time from the beginning of the chapter which is currently playing.
Remaining time: Remaining time of the title which is currently playing.
GOTO function
This function allows you to skip directly to any part of the disc while a disc is playing.
Locating a specific title
DVD
If a DVD contains title numbers, you can locate a specific title by directly selecting its title number.
1.In stop mode, press the GOTO button.
or
button to highlight a specific field and press the corresponding
2.Press
number button(s) for the title you want.
3.Press the ENTER button to confirm. The unit will start playback about 3 seconds later.
Locating a specific title /chapter / track
If you know the title / chapter / track number for the title / chapter / track that you want to play, you can locate it by
directly selecting that number.
1. Press the GOTO button to search for your desired title / chapter / track.
2. Press or button to highlight a title / chapter / track and press the corresponding
number button(s) for the chapter you want.
3. Press the ENTER button to confirm. The unit will start playback about 3 seconds
later.
Locating a specific time
You can move to a specific location by entering its corresponding time (hours, minutes, seconds)
1. Press the GOTO button.
2. Press or button to highlight time.
3. Press the corresponding number buttons for the setting point you want.
4. Press the ENTER button to confirm. The unit will start playback about 3 seconds
later.
Notes :
• Some discs may not respond to this process.
• Some scenes may not be located as precisely as you specified.
• This method for accessing specific locations is available only within the current title of the DVD disc.
E - 16
P14-18.pmd
16
10/18/2005, 12:07 PM
DVD
CD / DVD PROGRAMMABLE MEMORY
Programmable memory
The two types of programmed playback provided by this unit are title/chapter programmed playback and track
programmed playback.
Title / Chapter programmed playback
1. Press the MEMORY button while the disc is stopped.
2. Enter the title numbers in
in - - .
--
. Use
or
button to highlight your desired chapter and enter the chapter numbers
3. Use , , or button to move to another field.
4. Repeat steps 2 to 3.
5. Press the PLAY button to start the programmed playback.
Title
Programmable memory
Chapter
CD
Track programmed playback
1. Press the MEMORY button while the disc is stopped.
2. Enter the track numbers in
---
.
Track
3. Use , , or button to select other field.
4. Repeat steps 2 to 3.
5. Press the PLAY button to start the programmed playback.
E - 17
P14-18.pmd
17
10/18/2005, 12:07 PM
DVD
REPEAT PLAYBACK
You can play a specific title or chapter repeatedly.
(Title repeat, chapter repeat, A-B repeat)
REPEATING A DVD CHAPTER
While the disc is playing, press the REPEAT DISC button until the “ Repeat Chapter ” indicator displays on the screen.
The current chapter is played repeatedly.
REPEATING A DVD TITLE
While the disc is playing, press the REPEAT DISC button until the “ Repeat Title ” indicator displays on the screen.
The current title is played repeatedly.
RESUMING NORMAL DVD PLAYABCK
While the disc is playing, press the REPEAT DISC button until the “
Off
” indicator displays on the screen.
You can play a single track or the whole DVD repeatedly.
REPEATING A SINGLE CD TRACK
While the disc is playing, press the REPEAT DISC button until the “ Repeat Single ” indicator displays on the screen.
The current track is played repeatedly.
REPEATING A WHOLE CD
While the CD is playing, press the REPEAT DISC button until the “ Repeat All ” indicator displays on the screen. The
whole disc is played repeatedly.
RESUMING NORMAL CD PLAYBACK
Press the REPEAT DISC button until the “ Off ” indicator displays on the screen.
Repeating a specific section
You can play a specific section repeatedly.
1. While the disc is playing, press the REPEAT A-B button at the beginning of the section ((
you want to play repeatedly.
2. Press the REPEAT A-B button again at the end of the section (( Rep A-B ) is displayed).
3. The unit will immediately begin replaying your selection.
Rep A-
) is displayed)
To resume normal playback
4. While the disc is playing, press the REPEAT A-B button until the “ Off ” indicator displays on the screen.
Notes :
• A-B repeat can only be used within the same title. If the start and end of the section to be repeated are in different titles,
A-B repeat is cancelled.
• The A-B repeat function does not operate in scenes where different camera angles are recorded.
E - 18
P14-18.pmd
18
10/18/2005, 12:07 PM
PLAYING MP3 AND PICTURE FILES
This unit can play MP3 and Picture files recorded on CD-R and CD-RW discs.
Playing a MP3 /Picture file disc
1. Insert the MP3/Picture file disc.
2. Close the disc door.
3. The unit will load the disc and automatically display the contents of
the disc on the screen, while also beginning to play the first MP3 file
or Picture files. Each file will be played one after another.
4. Press the , , or CURSOR button to view and select the file(s) that
you want to play, then press the ENTER button to confirm the selected
file
CD-ROM
1/117
00:00:35
(Root)
1
Folk
6
Single
2
Rock
7
Car
3
Flower
8
Calender
4
Map
5
Modern
Notes:
• You can press the
PAUSE button to interrupt playback, and
press the
PLAY button to resume playback.
• You also can use GOTO function or use the numbered buttons to enter a photo number and quickly select
any image.
• Press the ANGLE button on the remote control to rotate the picture orientation by 90°.
Playable files
The ability of this unit to read MP3 discs is dependent on the following:
• The Bit Rate must be within 64 - 256 kbps.
• The total number of files on the disc should not exceed 254.
• The maximum number of directories should not exceed 32.
• The maximum depth level of directories should not exceed 4.
• File names should be named using 7 or fewer letters and/or numbers, and must incorporate the “MP3” file
extension. EXAMPLE: *******.MP3 where each * is a letter or number.
• Use only letters and / or numbers in file names. If you use special characters, the file and/or folder names
may not be displayed correctly on the on-screen display.
• When recording on CD-R discs, use 74-minute (650MB) discs.
• The CD-R or CD-RW discs should be “finalized” on the computer using “single session format” with
recording speed less than "8x".
• See your CD/MP3 creation software for more information.
E - 19
P19_V6.pmd
19
10/18/2005, 12:09 PM
CUSTOMIZING THE FUNCTION SETTINGS
LANGUAGE setting
Language
1. Press the SETUP button in stop mode.
2. Use or button to select a language, then press the ENTER button.
The screen will change to your selected language immediately.
English
Deutsch
3. To exit the SETUP MENU and return to the normal screen, press the
RETURN or SETUP button.
Français
Video
Español
Italiano
Svenska
Português
VIDEO setting
1. Press the SETUP button in stop mode.
2. Use or button to select Video, then press the ENTER button.
or
button to select the options (TV Shape, Brightness or
3. Use
or button, then press the ENTER
Edges) to be adjusted by press
button. (The screen will change to your desired setting).
4. Repeats step 2 and 3 above to adjust other options.
5. To exit the FUNCTION SETUP MENU and return to the normal screen,
press the RETURN or SETUP button.
Language
TV Shape
Brightness
Edges
Video
Letter Box
Off
Off
Cut off when a wide-screen
video image is played.
Pan Scan
• When wide-screen video is played, this mode clips the right and left
sides of the image so that it can be viewed on a conventional screen.
• Some wide-screen DVDs that do not permit Pan Scan playback are
automatically played in letterbox mode (black bands at top and bottom
of screen).
Pan Scan
Letter Box
• When wide-screen video is played in this mode on a conventional
screen, black bands appear at the top and bottom of the screen.
Letter Box
Wide-screen
• This is the correct mode for playing wide-screen videos on a
wide-screen.
Wide-screen
Notes :
• The displayable picture size is preset on the DVD disc. Therefore the playback picture of some DVDs may not
conform to the picture size you select.
• When you play DVDs recorded in the 4:3 aspect ratio, the playback picture will always appear in the 4:3 aspect
ratio regardless of the TV shape setting.
E - 20
P20-21_V6.pmd
20
(continued to next page)
10/18/2005, 12:18 PM
CUSTOMIZING THE FUNCTION SETTINGS
RATING
Some DVDs are equipped with a password function and are rated according to their content. The contents allowed
by parental lock levels and the way a DVD is controlled may vary from disc to disc. For example, if the disc allows,
you could lock-out violent scenes unsuitable for children or you could lock out playback of the disc altogether.
1. Press the SETUP button in stop mode.
2. Use
or
button to select the Rating, press the ENTER button.
3. Use
or
button to select parental lock and then press the
ENTER button repeatedly to set the parental lock level.
4. Use or button to shift and select Password, enter your 4-digit
security code and then press the ENTER button.
Rating
Password
Pare nta l lock
Fac tory Se t
---8. A dult
No
You cannot play DVDs rated higher than the level you selected unless you cancel the parental lock
function.
The parental lock levels are equivalent to the following ratings.
Level 1 : Kid Safe
Level 2 : G
Level 3 : PG
Level 4 : PG_13
Level 5 : PG_R
Level 6 : R
Level 7 : NC_17
Level 8 : Adult
Indicates Parental lock is NOT active.
The Parental lock is active.
If you forget the password, you can erase your current password by pressing
number button 8 on the remote four times, then press the ENTER button to
confirm the setting.
PASSWORD : 8 8 8 8
Note:
It takes 3-5 seconds to reset the unit to the factory default.
E - 21
P20-21_V6.pmd
21
10/18/2005, 12:18 PM
LANGUAGE CODE LIST FOR DISC LANGUAGE
Code Language Name Code Language Name Code Language Name Code Language Name
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DE
DZ
EL
EN
EO
ES
ET
EU
FA
FI
FJ
FO
FR
Afar
Abkhazian
Afrikaans
Ameharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byerlorussian
Bulgarian
Bihari
Bislama
Bengali
Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
German
Bhutani
Greek
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Faroese
French
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian, Lettish
FY
GA
GB
GL
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IT
IW
JA
JI
JW
KA
KK
KL
KM
KN
KO
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MS
MT
MY
NA
NE
NL
NO
OC
OM
OR
PA
PL
PS
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
Portuguese
Quechua
RhaetoRomance
Kirundi
Romanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
SerboCroatian
Singhalese
Slovak
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZH
ZU
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswat
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Chinese
Zulu
E - 22
P22-24_V6.pmd
22
10/18/2005, 12:21 PM
MAINTENANCE
Cleaning Disc
A defective or dirty disc inserted into the unit can cause sound to drop out during playback.
Handle the disc by holding its inner and outer edges.
• Do NOT touch the surface of the unlabeled side of the disc.
• Do NOT stick paper or tape on the surface of the disc.
• Do NOT expose the disc to direct sunlight or excessive heat.
• Clean the disc before playback. Wipe the disc from the center outward with a
cleaning cloth.
• NEVER use solvents such as benzine or alcohol to clean the disc.
• Do NOT use irregular shaped discs (example : heart shaped, octagonal, etc.). They may cause malfunctions.
Cleaning the unit
• Be sure to turn the unit off and disconnect the AC power cord before cleaning the unit.
• Wipe the unit with a dry soft cloth.
If the surfaces are extremely dirty, wipe clean with a cloth which has been dipped in a weak soap-and-water solution
and wrung out thoroughly, then wipe it with a dry cloth.
• Never use alcohol, benzine, paint-thinner, cleaning fluid or other chemicals. Do NOT use compressed air to remove
dust.
Important Note
Before shipping the unit, remove any disc from the disc compartment.
E - 23
P22-24_V6.pmd
23
10/18/2005, 12:21 PM
TROUBLE SHOOTING GUIDE
SYMPTOM
CAUSE (AND REMEDY)
No power.
• Make sure that the AC adapter is connected.
• Make sure that the unit is turned on.
The remote control
does not function.
• Make sure the infrared remote sensor is not blocked.
• Make sure the plastic sheet has been removed from the remote.
• Point the remote directly at the infrared remote sensor on the unit.
• Replace the battery in the remote with a new one.
DVD
Very little or no sound is
coming from a DVD
• Make sure the unit is in DVD mode.
• Make sure the unit is not paused. Press the
PLAY button.
• Make sure the unit is not in fast-forward or fast-reverse mode. Press the
button.
PLAY
• Make sure that AUDIO/VIDEO output and AV IN input connections are correct.
• Make sure you have not selected the "DTS" audio track on the DVD. This unit does not
decode "DTS" audio.
• The unit have overheated, shut it off for 30 minutes to allow it to cool down.
No picture
• The region number of the disc does not match the region number of the unit.
• DVD mode is not selected, select DVD on AV IN/DVD switch.
The picture is not clear
• The DVD is dirty. Gently clean the disc.
• The DVD is scratched.
Loud hum or noise is
heard.
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol.
The disc does not play.
• There is no disc inside the unit ("No Disc" appears on the screen).
• Clean the disc.
• Insert the disc correctly with the graphics facing up.
• Clean the disc.
• A non-NTSC disc has been inserted, or the disc region number does not match the
region number of the unit.
• Condensation may have formed inside the unit due to a sudden change in temperature.
Wait about an hour for it to clear and try again.
NOTICE: Kawasaki is trademark licensed by Kawasaki Motors Corp., U.S.A. However, this
product is neither manufactured nor distributed by Kawasaki Motors Corp., USA.
Consumer inquiries should be directed to Alco Electronics at www.1800customersupport.com
811-109291-012
Printed in China
E - 24
P22-24_V6.pmd
24
10/18/2005, 12:21 PM
Download PDF