ADEMCO | VISTA-50PEN | Setup guide | ADEMCO VISTA-50PEN Setup guide

$'(0&29,67$6(5,(6
9,67$39,67$38/
&RPPHUFLDO%XUJODU\
3DUWLWLRQHG6HFXULW\6\VWHP
:LWK6FKHGXOLQJ
3URJUDPPLQJ*XLGH
VISTA50P-PRV2 5/04 Rev A
Table of Contents
Relay Programming ................................................ 25
Relay Voice Descriptors ......................................... 28
Relay Voice Descriptors and Custom Word
Substitutes Vocabulary........................................ 29
Custom Word Substitutes for VIP Module
Annunciation........................................................ 30
System Layout Worksheets.................................... 31
Relay Devices Worksheets..................................... 39
Scheduling Menu Prompts ..................................... 41
Scheduling Worksheets .......................................... 42
VISTA-50P/VISTA-50PUL Summary of
Connections Diagram.......................................... 47
Recommended Programming Procedure................. 3
Program Field Index ................................................. 4
VISTA-50P/VISTA-50PUL Programming Form........ 5
Partition-Specific Fields .......................................... 10
Programming With #93 Menu Mode....................... 12
Zone Programming................................................. 13
5800 Series Transmitters Loop Designations ........ 15
Expert Mode Zone Programming ........................... 16
Alpha Descriptors Programming ............................ 20
Alpha Descriptor Vocabulary.................................. 23
Device Programming .............................................. 24
The purpose of this document is to provide a quick and easy way to program your entire system. A
recommended programming procedure is included, followed by a list of program fields with the corresponding
program group they belong to (system-wide, partition-specific, scheduling, etc.). Two program forms are
included. One contains all the programming fields, and the other contains the partition-specific fields. If you are
setting up a single-partition system, the partition-specific fields become system-wide fields.
Following the program forms are system layout worksheets. We recommend that you use these sheets to plan
your system before programming is performed. If you need further information about specific programming
options, see the ADEMCO VISTA-50P/VISTA-50PUL Installation and Setup Guide.
Make sure that one two-line alpha keypad is connected to the control and is set to device address "00."
Single-Partition System
The system default is for a single-partition system. Use the VISTA-50P/VISTA-50PUL SINGLE PARTITION
PROGRAMMING FORM when programming for single-partition usage. Follow the steps outlined in
RECOMMENDED PROGRAMMING PROCEDURE of this document for proper programming procedure.
Multiple-Partition System
You must enter the number of partitions you are using in data field 2*00 to set the system for multiple
partitions. Use the VISTA-50P/VISTA-50PUL SINGLE PARTITION and the PARTITION-SPECIFIC
PROGRAM FORMS when programming the system for multiple partitions. Follow the steps outlined in
RECOMMENDED PROGRAMMING PROCEDURE of this document for proper programming procedure.
•
•
•
•
•
•
•
•
•
SUMMARY OF PROGRAMMING COMMANDS
To enter program mode, enter installer code + [8] + [0] + [0]
To set standard defaults, press ✱97
To change to next page of program fields, press ✱94
To return to previous set of fields, press ✱99
To erase account and phone number field entries, press [✱] + field number + [✱]
To assign zone descriptors, press #93 + follow menu prompts
To add custom words, press #93 + follow menu prompts
To enter Installer's Message, press #93 + follow menu prompts
To exit program mode, enter ✱99 OR ✱98: ✱99 allows re-access to programming mode by installer code.
✱98 prevents re-access to programming mode by installer code.
Standard default (✱97) values are shown in brackets [ ], otherwise default = 0.
–2–
Recommended Programming Procedure
The following is a step-by-step procedure recommended for programming your VISTA-50P/VISTA-50PUL system.
1. Set the keypads (and other peripheral devices) to the appropriate addresses.
2. Set factory defaults by pressing ✱97.
This will automatically enable keypad addresses 00-03, so be sure at least one keypad is set to one of these
addresses.
3. Program system-wide (global) data fields.
Using the programming form as a guide, enter program mode and program all system-wide programming
fields. These options affect the entire system, regardless of partitions. They include control options,
downloader and dialer options, RF options, event logging options, etc. Refer to the Program Field Index for a
listing of the program fields and their function.
Note that field 2✱00 (number of partitions) must be programmed before continuing.
4. Program partition-specific fields.
When the system-wide fields have been programmed, program all partition-specific programming fields by
first pressing ✱91 to select a partition (while still in data field program mode). Then enter the first partitionspecific field number ✱09. When you are finished, the next partition-specific field is automatically displayed.
Partition-specific fields can have different values for each partition. To program the fields for the next partition,
press ✱91, enter the desired partition number, then enter field ✱09. Refer to the PROGRAMMING section in
the ADEMCO VISTA-50P/VISTA-50PUL Installation and Setup Guide for detailed instructions.
5. Use #93 Menu Mode for device programming.
Refer to Device Programming in this guide to assign keypad ID numbers and default partitions for each
keypad, and to selectively suppress certain keypad sounding options. Also use this mode to assign RF
receivers, relay modules, the VIP module, the ECP Long Range Radio, and the VISTA Gateway Module.
6. Use #93 Menu Mode for zone programming.
Refer to Zone Programming in this guide to program zone response types, assign right loop zones and
wireless zones, assign zones to partitions, and to program alarm report codes.
7. Use #93 Menu Mode for programming outputs.
Refer to Output Programming in this guide to program desired output operation.
8. Program Communication options.
Refer to System Communication section in the ADEMCO VISTA-50P/VISTA-50PUL Installation and Setup
Guide for detailed instructions. Then use #93 menu mode to program report codes.
9. Use #93 Menu Mode for programming alpha descriptors.
Refer to Alpha Programming in this guide to enter zone and partition descriptors and a custom installer’s
message.
10. Use #93 Menu Mode for relay voice descriptors and custom word substitutes.
Refer to Relay Voice Descriptors in this guide for further instructions for programming relay descriptors to be
annunciated by the VIP module, as well as the Custom Index section for custom word substitutes.
11. Use #80 Mode for programming schedules.
Refer to the Scheduling Menu Prompts in the ADEMCO VISTA-50P/VISTA-50PUL Installation and Setup
Guide to program open/close schedules, temporary and holiday schedules, limitation of access schedules,
and time-driven events.
12. Define user access codes.
Refer to User Access Codes in the ADEMCO VISTA-50P/VISTA-50PUL Installation and Setup Guide to
program authority level, O/C reporting option, partition assignments, and RF key assignments for each user.
13. Exit Programming Mode.
Exit programming mode by pressing either ✱98 or ✱99. Additional entries of ✱99 are required if the exit is
being done from fields 1✱00 and above.
To prevent re-access to programming mode using the Installer’s code, use ✱98. The only way to re-access
programming mode is by depressing both the [✱] and [#] keys at the same time within 30 seconds of powerup.
Exiting by using ✱99 always allows reentry into programming mode using the Installer code. Either way of
exiting allows access via downloading. Note that if local programming lockout is set via downloading,
programming mode cannot be entered at the keypad.
–3–
Program Field Index
On the following pages, the programming fields have been arranged in numerical order. Use this index to cross-reference the
fields on the programming form.
Field
Group
Field Group
Field Group
1*28
System-Wide
*57
Communications
*00
System-Wide
1*29
System-Wide
*58
Communications
*02
# 93 Menu Mode
1*30
System-Wide
*59
Communications
*03
# 93 Menu Mode
1*31
System-Wide
*60
Communications
*04
# 93 Menu Mode
1*33
Communications
*61
Communications
*05
# 93 Menu Mode
1*34
Communications
*62
Communications
*09
Partition-Specific
1*35
Communications
*63
Communications
*10
Partition-Specific
1*36
Communications
*64
Communications
*11
Partition-Specific
1*37
Communications
*65
Communications
*12
Partition-Specific
1*38
Communications
*66
Communications
*13
Partition-Specific
1*39
Communications
*67
Communications
*14
System-Wide
1*40
Communications
*68
Communications
*15
System-Wide
1*41
Communications
*69
Communications
*16
Partition-Specific
1*42
Communications
*70
Communications
*17
System-Wide
1*43
Partition-Specific
*71
Communications
*19
System-Wide
1*44
System-Wide
*72
Communications
*20
System-Wide
1*45
Partition-Specific
*73
Communications
*21
System-Wide
1*46
System-Wide
*74
Communications
*22
Partition-Specific
1*47
Partition-Specific
*75
Communications
*23
Partition-Specific
1*48
System-Wide
*76
Communications
*24
System-Wide
1*49
System-Wide
*77
Communications
*25
System-Wide
1*52
Partition-Specific
*78
Communications
*26
Communications
1*53
System-Wide
*79
Communications
*27
Communications
1*57
System-Wide
*80
Communications
*28
System-Wide
1*58
System-Wide
*81
Communications
*29
Partition-Specific
1*60
System-Wide
*82
Communications
*30
Communications
1*70
System-Wide
*83
Communications
*31
Communications
1*71
System-Wide
*84
Partition-Specific
*32
Partition-Specific
1*72
System-Wide
*85
Partition-Specific
*33
Communications
1*73
System-Wide
*87
Partition-Specific
*34
Communications
1*74
System-Wide
*88
Partition-Specific
*35
System-Wide
1*75
System-Wide
*89
Communications
*36
System-Wide
1*76
Partition-Specific
*90
Partition-Specific
*37
System-Wide
2*00
System-Wide
1*01
# 93 Menu Mode
*38
Partition-Specific
2*01
System-Wide
1*02
# 93 Menu Mode
*39
Partition-Specific
2*02
System-Wide
1*03
# 93 Menu Mode
*40
Communications
2*05
Partition-Specific
1*04
# 93 Menu Mode
*41
System-Wide
2*06
Partition-Specific
1*05
# 93 Menu Mode
*42
Communications
2*07
Partition-Specific
1*06
# 93 Menu Mode
*43
Communications
2*08
Partition-Specific
1*07
# 93 Menu Mode
*44
Communications
2*09
Partition-Specific
1*08
# 93 Menu Mode
*45
Communications
2*10
Partition-Specific
1*09
# 93 Menu Mode
*46
Communications
2*11
System-Wide
1*17
System-Wide
*47
Communications
2*13
Communications
1*18
Partition-Specific
*48
Communications
2*14
Communications
1*19
Partition-Specific
*49
Communications
2*18
Partition-Specific
1*20
System-Wide
*50
Communications
2*19
System-Wide
1*21
System-Wide
*51
Communications
2*20
Partition-Specific
1*22
System-Wide
*52
Communications
2*21
System-Wide
1*23
System-Wide
*53
Communications
1*24
System-Wide
*54
System-Wide
1*25
System-Wide
*56
Communications
–4–
VISTA-50P/VISTA-50PUL Programming Form
Some fields are programmed for each partition (shown as shaded fields). If you are programming a multiple-partition system,
see the Partition-Specific Fields section for programming these fields. Standard default (*97) values are shown in brackets [ ].
| | |
*00 INSTALLER CODE
*25 BURG.TRIGGER FOR RESPONSE TYPE 8
Enter 4 digits, 0-9 [4140]
*02
*05
[1]
1=enable; 0=disable
RESPONSE TYPES FOR ZONES
*26 INTELLIGENT TEST REPORTING
Skip these fields. Use #93 Menu Mode, Zone
Programming to program the response types.
*09 ENTRY DELAY #1
|
[02]
00, 02-15 times 15 seconds
Maximum "03" for UL.
[024]
*27 TEST REPORT INTERVAL
*10 EXIT DELAY #1
00, 03-15 times 15 seconds
Maximum "04" for UL installations.
| | |
Enter interval in hours, 001-999; 0000=no report;
Max. 024 for UL installations.
|
[03]
[0]
1=yes (no report sent if any other report was recently sent);
0=no (send report at programmed interval, field *27)
Must be 0 for UL installations.
*28 POWER UP IN PREVIOUS STATE
*11 ENTRY DELAY #2
|
[06]
00, 02-15 times 15 seconds (must be longer than Entry Delay
#1). Maximum "03" for UL installations.
*12 EXIT DELAY #2
|
[08]
00, 03-15 times 15 seconds (must be longer than Exit Delay
#1). Maximum "04" for UL installations.
*13 ALARM SOUNDER DURATION
01-15 times 2 minutes. Must be minimum 16 minutes for UL
installations.
*14 ZONE 9 RESPONSE TIME
1=yes; 0=no; "1" for UL installations.
*29 QUICK ARM
[1]
1=yes; 0=no
*30 TOUCHTONE OR ROTARY DIAL
[0]
1=TouchTone; 0=rotary
*31 PABX ACCESS CODE
|
[04]
[1]
|
|
|
|
|
|
|
|
00-09; B-F (11-15)
*32 PRIM. SUBS. ACCT #
Enter 00-09; B-F (11-15) [15 15 15 15]
[0]
*33 PRIMARY PHONE NUMBER
Enter 1 for fast response time 10ms
Enter 0 for normal response time 350ms.
Must be 0 for UL installations.
*15 KEYSWITCH ASSIGNMENT
[0]
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
Enter partition in which keyswitch used,
1-8; 0=disable
*34 SECONDARY PHONE NUMBER
*16 CONFIRMATION OF ARMING DING
[0]
1=enable; 0=disable.
Must be "1" for UL Installations.
*17 AC LOSS KEYPAD SOUNDING
[0]
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
1=yes; 0=no
*35 DOWNLOAD PHONE NO.
*19 RANDOMIZE AC LOSS REPORT
[0]
1=10-40 min; 0=normal report (about 2 min. after AC loss).
|
*20 VIP MODULE PHONE CODE
Enter 01 - 09 for the first digit; enter
11 for “*” or 12 for “#” for the second digit.
Must be set to "0" for UL installations.
|
[00],
Enter 0-9 for each digit. Enter #11 for *, #12 for #,
#13 for 2 second pause
[11]
*36 DOWNLOAD ID NO.
*21 PREVENT FIRE TIMEOUT
|
[0]
1=enable; 0=disable
|
|
|
|
|
|
Enter 00-09; A-F (10-15) [15 15 15 15 15 15 15 15]
1=No timeout; 0=Timeout.
*22 KEYPAD PANIC ENABLES
|
*37 DOWNLOAD COMMAND ENABLES
[001]
995
996
0
999
Dlr ShtdwnSys ShtdwnNot UsedRmt BypRmt DisarmRmt ArmUpld PgmDwnld Pgm
*23 MULTIPLE ALARMS
See field 1*53 for Callback disable option; [1=enable];
0=disable. For UL installations, all entries must be "0."
[1]
1=yes; 0=no
*24 IGNORE EXPANSION ZONE TAMPER
[0]
*38 PREVENT ZONE XX BYPASS
[00]
|
01-86; 00 if all zones (except fire zones) can be bypassed
1=Ignore; 0=Enable tamper for RF and RPMs.
Must be "0" for UL installations if using these devices.
–5–
*39 ENABLE OPEN/CLOSE REPORT FOR
*58 SUPERVISORY AND RESTORE CODES FOR ZONES
[0]
01-16. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]
INSTALLER CODE 1=enable; 0=disable
*40 OPEN/CLOSE REPORT FOR KEYSWITCH
[0]
*59
1=enable; 0=disable
*41 NORMALLY CLOSED or EOLR (Zones 2-8)
*62
[1]
|
|
|
Trbl Rst
Byp
Byp Rst
ALARM REPORT CODES & ID DIGITS FOR
ZONES 17-32.
*63 SUPERVISORY AND RESTORE CODES FOR ZONES
*42 DIAL TONE PAUSE
17-32. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]
[0]
0=5 seconds; 1=11 seconds; 2=30 seconds.
Must be "0" UL Installations.
*43 DIAL TONE DETECTION
*64
[1]
*67
1=wait for true dial tone; 0=pause, then dial
*44 RING DETECTION COUNT
*45 PRIMARY FORMAT
*69
*72
[0]
[0]
*74
0= ADEMCO Low Speed; 1=Sescoa/Radionics
Prim
Sec
|
|
|
|
Trbl
Trbl Rst
Byp
Byp Rst
ALARM REPORT CODES & ID DIGITS FOR
ZONES 49-64.
*77
|
|
|
|
|
Alarm Rst
Trbl
Trbl Rst
Byp
Byp Rst
ALARM REPORT CODES & ID DIGITS FOR
ZONES 81-99.
*78 SUPERVISORY AND RESTORE CODES FOR ZONES
81-99. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]
[0]
1=Sescoa; 0=Radionics
*51 DUAL REPORTING
|
Alarm Rst
Skip these fields. Use #93 Menu Mode, Zone
Programming to program the report codes.
[0] [0]
*50 SESCOA/RADIONICS SELECT
ALARM REPORT CODES & ID DIGITS FOR
ZONES 33-48.
49-64. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]
0=Low Speed; 1=Contact ID; 2= ADEMCO High Speed;
3= ADEMCO Express
1=yes; 0=no
|
Byp Rst
*73 SUPERVISORY AND RESTORE CODES FOR ZONES
[1]
*49 CHECKSUM VERIFICATION
|
Byp
Skip these fields. Use #93 Menu Mode, Zone
Programming to program the report codes.
0= ADEMCO Low Speed; 1=Sescoa/Radionics
*48 LOW SPEED FORMAT (Sec.)
|
Trbl Rst
33-48. Enter 00-09; B-F (11-15). Default = [00 00 00 00 00]
0=Low Speed; 1=Contact ID; 2=ADEMCO High Speed;
3= ADEMCO Express
*47 SECONDARY FORMAT
|
Trbl
*68 SUPERVISORY AND RESTORE CODES FOR ZONES
[1]
*46 LOW SPEED FORMAT (Primary)
|
Alarm Rst
Skip these fields. Use #93 Menu Mode, Zone
Programming to program the report codes.
|
[00]
01-14; 15=answering machine; 00=no detection.
Must be "00" for UL Burglary.
[0]
1=yes; 0=no If used with Spilt Reporting "1" option (1*34),
alarms and alarm restores go to both primary & secondary
numbers, while all other reports go to secondary only. If used
with Split Reporting "2" option, alarms and alarm restores go to
both, open/close and test messages go to secondary only,
while all other reports go to primary.
|
|
|
|
|
Alarm Rst
Trbl
Trbl Rst
Byp
Byp Rst
ZONE TYPE RESTORE ENABLES
*79 FOR ZONE TYPES 1-8
1
2
3
4
5
1=enable; [0=disable]
*52 STANDARD/EXPANDED REPORT FOR PRIMARY
6
7
8
*80 FOR TYPES 9, and 10
[0 0 0 0 0 0]
Alarm Rstr
Byp
Trbl
9
O/C LoBat
1=enable; [0=disable]
0=standard; 1=expanded;
Note: Expanded overrides 4+2 format.
*53 STANDARD/EXPANDED REPORT FOR SECONDARY
[0 0 0 0 0 0]
Alarm Rstr
Byp
Trbl
O/C LoBat
0=standard; 1=expanded;
*57
|
Trbl
Skip these fields. Use #93 Menu Mode, Zone
Programming to program the report codes.
1=N.C.loops; 0=EOLR supervision.
Must be "0" for UL installations.
*54
|
Alarm Rst
ALARM REPORT CODES & ID DIGITS FOR
ZONES 01-16.
Skip these fields. Use #93 Menu Mode, Zone
Programming to program the report codes.
–6–
10
*80
*81
SYSTEM NON-ALARM CODES
Enter 00-09; B-F (11-15).
Default = 00 for all reports
*80 1st Digit
1*20 EXIT ERROR LOGIC ENABLE
0=No; 1=Bypass E/E and Interior zones faulted after exit
delay.
Must be "0" for UL installations.
*81 2nd Digit
Close
|
|
Open
|
|
Low Battery
|
|
Low Battery Restore
|
|
AC Loss
|
|
AC Restore
|
|
Test
|
|
Power Up
|
|
Cancel
|
|
Program Tamper
|
|
[0]
1*21 EXIT DELAY RESET
[0]
0=No; 1=Resets Exit Delay to programmed value after zone
is closed and then faulted prior to end of exit delay.
Must be "0" for UL installations.
FIELDS 1✳22-1✳25: Allow four sets of two zones each to be
linked so that both must fault within a five minute period to
cause an alarm. Default for these fields = [000], [000].
1*22 CROSS-ZONING PAIR ONE
|
|
1*23 CROSS-ZONING PAIR TWO
|
|
1*24 CROSS-ZONING PAIR THREE
|
|
1*25 CROSS-ZONING PAIR FOUR
|
|
MISCELLANEOUS WIRELESS OPTIONS
Fields 1*28 - 1*31 are not applicable for UL installations.
1*28 RF TX LOW BATTERY SOUND
|
*83 FIRST TEST REPORT TIME
|
|
1=immediate; 0=when disarmed
[Day 00; hour 12; min 00] Days 01-07 Hours 00-23 Min 0059; 00 in all boxes = instant (Day 01= Monday)
*84 SWINGER SUPPRESSION
1*29 RF TX LOW BATTERY REPORTING
1*30 RF RCVR CHECK-IN INTERVAL
01-15 alarms
Must be "00" (disabled) for UL.
1*31 RF XMITTER CHECK-IN INTERVAL
995 996 999 Duress
*87 ENTRY WARNING
[0]
1=enable; 0=disable
[0]
*89 RESTORE REPORT TIMING
1*35
[0]
|
|
Skip these fields. Use #93 Menu Mode, Zone
Programming to program the report codes.
1*39 SUPERVISORY AND RESTORE CODES FOR
|
ZONES 65-80. Enter 00-09; B-F (11-15).
[15 15 15 15]
Default = [00 00 00 00 00]
2nd Page Programming Fields (press *94)
1*09 ASSIGN RESPONSE TYPE FOR ZONES.
Skip these fields. Use #93 Menu Mode, Zone
Programming to program the response types.
1*17 LOBBY PARTITION
1*38 ALARM REPORT CODES & ID DIGITS FOR
ZONES 65-80.
0=Instant; 1=After bell timeout if zone is restored; 2=when
system is disarmed. Must be "0" for UL installations.
|
[0]
0=no; 1=alarms and alarm restores primary, others secondary;
2=open/close, test secondary, others primary. See 751 for
comments if using with dual reporting.
1=16 seconds; 0=no delay
Must be "0" for UL installations.
[0]
Enter the "common lobby" partition (1-8)
[0]
Enter 1 if this partition affects the common lobby; enter 0 if it
does not.
Must be "0" for UL installations.
1*19 ARMS LOBBY
|
1*34 COMM. SPLIT REPORTING
*88 BURG. ALARM COMM. DELAY
1*18 AFFECTS LOBBY
[12]
1*33 TOUCHTONE W/ROTARY BACKUP
[1]
1=continuous; 0=3 beeps
1*01
|
02-15 times 2 hours; 00 disables transmitter supervision
1=enable; [0=disable]
Enter 00-09; B-F (11-15)
[06]
02-15 times 2 hours; 00 disables supervision
*85 ENABLE DIALER REPORTS FOR PANICS & DURESS
*90 SEC. SUBS. ACCT #
[0]
1=enable; 0=disable
|
[01]
[0]
[0]
Enter 1 if arming this partition attempts to arm lobby; enter 0
if it does not.
Must be "0" for UL installations.
–7–
|
|
|
|
|
Alarm Rst
Trbl
Trbl Rst
Byp
Byp Rst
1*40
1*41 NON-ALARM DIALER CODES
Enter 00-09; B-F (11-15).
Default = 00 for all reports
1*40 1st Digit
1*58 5800 RF BUTTON FORCE ARM
Enter "1" to enable. If a zone is faulted after pressing button,
keypad will beep once. Pressing the button again within 4
sec. bypasses the zone. Enter "0" to disable.
Must be "0" for UL installations.
1*41 2nd Digit
Armed STAY
|
|
Time/Date Set or Event Log Reset
|
|
Event Log 50% & 90% Full
|
|
Event Log Overflow
|
|
Exit Error (Zone)
|
|
Exit Error (User)
|
|
Recent Close
|
|
1*60 ZONE 5 AUDIO ALARM VERIFICATION
1*69 PRINTER TYPE
[0]
Enter 0 if you are using a parallel printer connected to the
VA8201 Alpha Pager Module.
Enter 1 if you are using a serial printer.
1*70 EVENT LOG TYPES
[1 0 0 0 1]
[0]
Byp
O/C
Syst
1=enable; 0=disable
1=Yes; 0=No
1*43 PERM. KEYPAD BACKLIGHT
[0]
Enter 1 If 2-way audio (AAV) is being used; Enter 0 if it is
not.
Must be "0" for UL installations.
Alarm Chk
1*42 CALL WAITING DEFEAT
[0]
1*71 12/24 HOUR TIME STAMP FORMAT
[0]
[0]
0=12 hour; 1=24 hour
1=enable; 0=disable When disabled, display lights when any
key is pressed, and turns off after period of keypad inactivity.
1*72 EVENT LOG PRINTER ON-LINE
[0]
0=disable; 1=enable
1*44 WIRELESS KEYPAD TAMPER
[0]
1*73 PRINTER BAUD RATE
DETECTION
1=enable; 0=disable.
Must be "0" for UL installations.
1*45 EXIT DELAY SOUNDING
Enter the relay timeout, 000-127 in multiples of 2 minutes,
desired for #80 Menu Mode time-driven event relay
command numbers "04/09" and #93 Menu Mode Output
Programming output command "56."
[0]
Enter 0 for ground start output.
Enter 1 for open/close trigger (is produced only if all partitions
are armed.
Enter 2 for keypad-like sounding. Applies to the partition
enabled in field *15.
Enter 3 if AAV module is being used.
NOTE: Only one of the above options may be active within
the system.
1*47 CHIME ON EXTERNAL SIREN
Enter the relay timeout, 000-127 seconds, desired for #80
Menu Mode time driven event relay command numbers
"05/10" and #93 Menu Mode Output Programming command
"57."
1*76 ACCESS CONTROL RELAY
[1]
2*00 NUMBER OF PARTITIONS
START/END MONTH
|
Start
End
[1, 5]
|
00-12; if no daylight saving time, enter 00,00
[1]
2*02 DAYLIGHT SAVING TIME
START/END WEEKEND
Start | End
Enter 1-7. 1=first; 2=second; 3=third; 4=fourth; 5=last;
6=next to last; 7=3rd from last [1,5]
[0]
1=callback not required; 0=callback required.
Must be "0" for UL installations.
1*57 5800 RF BUTTON GLOBAL ARM
|
2*01 DAYLIGHT SAVING TIME [04, 10]
1=no restriction; 0=within bell timeout period only
1*53 DOWNLOAD CALLBACK
[1]
Enter 1-8
1=disable; 0=enable.
Must be "0" for UL installations.
1*52 SEND CANCEL IF ALARM + OFF
|
[00]
Relay will be pulsed for 2 seconds whenever code + [0] is
pressed. Enter 00-16; 00=none.
Must be "00" for UL.
3rd Page Programming Fields (press *94)
[0]
0=disable; enter partition in which RF keypad used, 1-8.
Must be "0" for UL installations.
1*49 SUPPRESS TX SUPERVISION SOUND
| |
1*75 RELAY TIMEOUT YYY SECONDS [000]
[0]
1=enable; 0=disable
1*48 WIRELESS KEYPAD ASSIGNMENT
| |
1*74 RELAY TIMEOUT XXX MINUTES [000]
[0]
1=enable; 0=disable. Produces quick beeping during exit
delay if enabled.
1*46 AUXILIARY OUTPUT MODE
[0]
1=300; 0=1200
2*05 AUTO-ARM DELAY
[15]
|
Enter the time between the end of the arming window and
the start of auto-arming warning period, in values of 1-14
times 4 minutes 00=instant; [15=no auto arm at all]. When
this delay expires, the Auto-Arm Warning Period begins.
[0]
1=enable; 0=disable
–8–
2*06 AUTO-ARM WARNING PERIOD
|
[15]
2*18 ENABLE GOTO FOR THIS PARTITION
This is the time during which the user is warned to exit the
premises prior to the auto-arming of the system (beeps every
15 seconds; "ALERT" displayed). Enter 01-15 minutes.
00=instant at end of arming delay.
2*07 AUTO-DISARM DELAY
|
[15]
2*08 ENABLE FORCE ARM FOR AUTO-ARM
2*19 USE PARTITION DESCRIPTORS
2*21 ENABLE SUPERVISION PULSES FOR LRR
[0]
TRIGGER OUTPUTS
2*09 OPEN/CLOSE REPORTS BY EXCEPTION [0]
1=enable; 0=disable
If enabled, only openings and closings occurring outside the
scheduled opening/closing windows will trigger dialer
reports. Opening reports will also be suppressed during the
closing window, in order to prevent false reports when the
user arms the system and then reenters the premises to
retrieve a forgotten item.
•
ARMING/DISARMING WINDOWS
•
•
•
•
0=disable; 1=enable
See system-wide field 2*11 if enabling field 2*10. This
feature adds high security to the installation.
2*11 ALLOW DISARM OUTSIDE WINDOW
[0]
•
IF ALARM OCCURS
Used only if field 2*10 (partition-specific field) is set to "1." If
this field is enabled ("1") the system can be disarmed outside
the disarm window if an alarm has occurred. If "0," disarming
can only be done during the disarm window. If field 2*10 is
set to "0" for a partition, this field has no effect for that
partition.
2*13
•
•
•
2*14 SCHEDULING RELATED REPORT CODES
Enter 00-09; B-F (11-15).
Default = 00 for all reports
2*13 1st Digit
2*14 2nd Digit
Early Opening
|
|
Early Closing
|
|
Late Opening
|
|
Late Closing
|
|
No Opening (late to open)
|
|
No Closing (late to close)
|
|
Auto-Arm Failure
|
|
Access Schedule Changed
|
|
[000]
Used for supervised connection to 7920SE.
F
Enter 0 to disable or 1 to enable the listed outputs.
F= Fire; B= Burglary; P= Silent Panic/Duress.
Must be 1 for UL. Installations.
[0]
[1]
0=disable for displayed partition; 1=enable for displayed
partition
0=disable; 1=enable
2*10 ALLOW DISARMING ONLY DURING
[0]
0=disable; 1=enable
2*20 ENABLE J7 TRIGGERS FOR PARTITION
This is the time between the end of the disarming window
and the start of auto-disarming. Enter 01-14 times 4 minutes;
00=instant at end of window; 15=no auto-disarm.
[0]
1=Allow log-on from other partitions; 0=disable
–9–
| |
B
P
SUMMARY OF PROGRAMMING COMMANDS
To enter program mode, enter installer code + [8] + [0] +
[0]
To set standard defaults, press *97
To change to next page of program fields, press *94
To return to previous set of fields, press *99
To erase account and phone number field entries,
press [*] + field number + [*]
To assign zone descriptors, press #93 + follow menu
prompts
To add custom words, press #93 + follow menu prompts
To enter Installer's Message, press #93 + follow menu
prompts
To exit program mode, enter *99 OR *98: *99 allows reaccess to programming mode by installer code. *98
prevents re-access to programming mode by installer
code.
Partition-Specific Fields
(Duplicate this page for each partition in the installation.)
To program these fields,
1. Press *91 to select a partition.
2. Enter a partition-specific field number (ex. *09).
3. Make the required entry.
4. Repeat steps 1-3 for each partition in the system.
PARTITION #____ PROGRAM FIELDS
1st Page Fields
*09
*87
ENTRY DELAY #1
|
[02]
*88
EXIT DELAY #1
[03]
|
[06]
|
*90
ENTRY DELAY #2
EXIT DELAY #2
ALARM SOUNDER DURATION
1*19 ARMS LOBBY
|
[04]
CONFIRMATION OF ARMING DING
KEYPAD PANIC ENABLES
1*20 EXIT ERROR LOGIC ENABLE
[0]
[001]
1*21 EXIT DELAY RESET
995 996 999
MULTIPLE ALARMS
1*43 PERM. KEYPAD BACKLIGHT
QUICK ARM
PRIM. SUBS. ACCT #
[1]
|
|
|
|
1*45 EXIT DELAY SOUNDING
PREVENT ZONE XX BYPASS
|
[00]
ENABLE OPEN/CLOSE REPORT
1*47 CHIME ON EXTERNAL SIREN
1*52 SEND CANCEL IF ALARM + OFF
FOR INSTALLER CODE
[0]
[0]
[1]
1=no restriction; 0=within Bell Timeout period only
SWINGER SUPPRESSION
[01]
|
1*76 ACCESS CONTROL RELAY FOR PART.[00]
01-15 alarms;
Must be "00" (disabled) for UL installations..
*85
[0]
1=enable; 0=disable
[0]
1=enable; 0=disable
*84
[0]
1=enable; 0=disable. Produces quick beeping during exit
delay if enabled.
01-86; 000 if all zones (except fire zones) can be bypassed
*39
[0]
1=enable; 0=disable. When disabled, display lights when
any key is pressed, and turns off after period of keypad
inactivity.
Enter 00-09; B-F (11-15) [15 15 15 15]
*38
[0]
0=No; 1=Resets Exit Delay to programmed value after zone
is closed and then faulted prior to end of exit delay.
Must be "0" for UL installations.
[1]
1=yes; 0=no
*32
[0]
Enter 1 if arming this partition attempts to arm lobby; enter 0
if it does not
1=yes; 0=no.
Must be 1 for UL installations.
*29
|
0=No; 1=Bypass E/E and Interior zones faulted after exit
delay.
Must be "0" for UL installations.
1=enable; 0=disable
*23
|
Enter 1 if this partition affects the common lobby; enter 0 if it
does not.
1=enable; 0=disable.
Must be "1" for UL installations.
*22
|
[15 15 15 15]
1*18 AFFECTS LOBBY
|
[08]
01-15 times 2 minutes.
Must be minimum 16 minutes for UL installations.
*16
[0]
2nd Page Programming Fields (press *94)
00, 03-15 times 15 seconds.
Maximum 04 for UL installations.
*13
|
SEC. SUBS. ACCT #
Enter 00-09; B-F (11-15)
00, 02-15 times 15 seconds.
Maximum 03 for UL installations.
*12
BURG. ALARM COMM. DELAY
1=16 seconds; 0=no delay.
Must be "0" for UL installations. Must be “1” for SIA
installations.
00, 03-15 times 15 seconds.
Maximum 04 for UL Listed installations.
*11
[1]
1=continuous; 0=3 beeps
00, 02-15 times 15 seconds.
Maximum 03 for UL Listed installations.
*10
ENTRY WARNING
ENABLE DIALER REPORTS FOR PANICS & DURESS
1=enable; [0=disable]
995 996 999 Duress
– 10 –
|
Relay will be pulsed for 2 seconds whenever code + [0] is
pressed. Enter 00-16; 00=none.
Must be "00" for UL installations.
3rd Page Programming Fields (press *94)
2*05 AUTO-ARM DELAY
2*18 ENABLE GOTO FOR THIS PARTITION
|
[15]
1=Allow log-on from other partitions; 0=disable
Enter the time between the end of the arming window and
the start of auto-arming warning period, in values of 1-14
times 4 minutes 00=instant; [15=no auto arm at all]. When
this delay expires, the Auto-Arm Warning Period begins.
2*06 AUTO-ARM WARNING PERIOD
2*20 ENABLE J7 TRIGGERS BY PARTITION
|
[15]
|
[15]
This is the time between the end of the disarming window
and the start of auto-disarming. Enter 01-14 times 4 minutes;
00=instant at end of window; 15=no auto-disarm
2*08 ENABLE FORCE ARM FOR AUTO-ARM
SUMMARY OF PROGRAMMING COMMANDS
•
•
•
•
•
[0]
•
0=disable; 1=enable
2*09 OPEN/CLOSE REPORTS BY EXCEPTION [0]
1=enable; 0=disable If enabled, only openings and closings
occurring outside the scheduled opening/closing windows
will trigger dialer reports. Opening reports will also be
suppressed during the closing window, in order to prevent
false reports when the user arms the system and then reenters the premises to retrieve a forgotten item.
2*10 ALLOW DISARMING ONLY DURING
[1]
0=disable for displayed partition; 1=enable for displayed
partition
This is the time during which the user is warned to exit the
premises prior to the auto-arming of the system (beeps
every 15 seconds; "ALERT" displayed). Enter 01-15 minutes.
00=instant at end of arming delay .
2*07 AUTO-DISARM DELAY
[0]
•
•
•
[0]
ARMING/DISARMING WINDOWS
See system-wide field 2*11 if enabling field 2*10. This
feature adds high security to the installation.
0=disable; 1=enable
– 11 –
To enter program mode, enter installer code + [8] + [0] +
[0]
To set standard defaults, press *97
To change to next page of program fields, press *94
To return to previous set of fields, press *99
To erase account and phone number field entries,
press [*] + field number + [*]
To assign zone descriptors, press #93 + follow menu
prompts
To add custom words, press #93 + follow menu prompts
To enter Installer's Message, press #93 + follow menu
prompts
To exit program mode, enter *99 OR *98: *99 allows reaccess to programming mode by installer code. *98
prevents re-access to programming mode by installer
code.
Programming With #93 Menu Mode
NOTE: The following field should be preset before beginning: 2*00 Number of Partitions. In addition, receivers should
be programmed via Device programming.
After programming all system related programming fields in the usual way, press #93 while still in programming mode to
display the first choice of the menu driven programming functions. Press 0 (NO) or 1 (YES) in response to the displayed menu
selection. Pressing 0 will display the next choice in sequence.
#93 MENU MODE KEY COMMANDS
The following is a list of commands used while in the menu mode.
#93
Enters Menu mode
[4]
Serves as ENTER key. Press to have keypad accept entry.
[#]
Backs up to previous screen.
0
Press to answer NO
1
Press to answer YES
01-09
All data entries are either 1-digit or 2-digit entries.
00
Exits menu mode, back into field programming mode, when entered at the first question for each category.
Menu selections are as follows:
PROMPT
EXPLANATION
ZONE PROG?
1 = YES 0 = NO
For programming the following:
• Zone Number
• Zone Response Type
• Partition Number for Zone
• Dialer report code for zone
• Input Device Type for zone (whether RF, polling loop, etc.)
• Enrolling serial numbers of 5800 Series transmitters & serial polling loop devices into the system.
0
EXPERT MODE?
1 = YES 0 = NO
0
ALPHA PROG?
1 = YES 0 = NO
0
DEVICE PROG?
1 = YES 0 = NO
RELAY PGM?
1 = YES 0 = NO
0
Same as Zone Programming except:
• Done with a minimum number of keystrokes.
• Can program wireless keys using pre-defined templates.
For entering alpha descriptors for the following:
• Zone Descriptors
• Installer's Message
• Custom Words
• Partition Descriptors
• Relay Descriptors
For defining the following device characteristics for addressable devices, including keypads, RF receivers
(5881), output relay modules (4204), and 4285/4286 VIP Module:
• Device Address
• Device Type
• Keypad Options (incl. partition assignment)
• RF House ID
For defining output relay functions.
0
For entering voice descriptors for relays to be used with the 4285/4286 VIP Module.
RLY VOICE DESCR?
1 = YES 0 = NO
0
CUSTOM INDEX ?
1 = YES 0 = NO
0
For creating custom word substitutes for VIP Module annunciation.
– 12 –
Zone Programming
If using 5800 Series transmitters, do not the install batteries until you are ready to enroll them. After enrolling
the transmitter, the battery need not be removed. This is to prevent enrolling the wrong serial number.
PROMPT
EXPLANATION
ZONE PROG?
1 = YES 0 = NO
0
SET TO CONFIRM?
1 = YES 0 = NO
0
ENTER ZONE NO.
00 = QUIT
Press 1 to enter ZONE PROGRAMMING mode. The following screens appear. Press [✱] to display the next
screen. Press # to display a previous screen.
This prompt appears once upon entering Zone Programming Mode.
If “Yes,” Confirmation prompts will be displayed after the device’s Serial and Loop numbers have been
entered later.
10
Zone 10 entered ↑
This display appears, showing a summary of the zone's current programming. ZT = Zone Type, P =
Partition, RC = Report Code, In = the input type of device, and L = the device's loop number to which the
sensor is connected.
Some devices can support more than one zone by means of individual loops (for example, 5801, 5804,
5816, 5817, etc.). If the zone is not programmed, the display appears as shown here. If you are checking a
zone's programming, and it is programmed satisfactorily, press [#] to back up one step and enter another
zone number, if desired.
Press [✱] to continue.
10 ZT P RC In L
00 1 10 00 1
10 ZONE TYPE
PERIMETER
Enter the 2-digit zone number to be programmed, as follows:
Protection Zones = 01–86
System Supervisory Zones = 88, 89, 90, 91, 92 (duress), 97 and 98 (bell supervision)
Keypad Panic Zones = 95, 96, 99
Press [✱] to continue.
03
Zone number 10 and Zone
Type 03 entry shown
† These are special zone
types used with 5800
Series Wireless
Pushbutton Units that
result in arming the system
in the STAY or AWAY
mode, or disarming the
system, depending on the
selection made.
Each zone must be assigned a zone type, which defines the way in which the system responds to faults in
that zone. Refer to the Zone Type Definitions section in the ADEMCO VISTA-50P/VISTA-50PUL Installation
and Setup Guide for detailed definitions of each zone type. Enter the zone type desired (or change it, if
necessary). Available zone types are listed below.
00 = Assign for Unused Zones
01 = Entry/Exit #1, Burglary
02 = Entry/Exit #2, Burglary
03 = Perimeter, Burglary
04 = Interior Follower, Burglary
05 = Trouble Day/Alarm Night
06 = 24 Hr. Silent Alarm
07 = 24 Hr. Audible Alarm
08 = 24 Hr. Auxiliary
09 = Fire Without Verification
10 = Interior Delay, Burglary
20 = Arm–STAY†
21 = Arm AWAY†
22 = Disarm†
23 = No Alarm Response
(e.g., relay activation)
Press [✱] to continue.
10 Partition
1
10 REPORT CODE
1st 03 2nd 12
3C
Enter the partition number (1–8) you are assigning this zone to.
Press [✱] to continue.
Enter the report code. The report code consists of 2 hexadecimal digits, each in turn consisting of 2
numerical digits. For example, for a report code of "3C," enter 03 for "3" and 12 for "C."
(Refer to the System Communication section in the Installation and Setup Guide for more information about
report codes and reporting formats.)
Press [✱] to continue.
– 13 –
PROMPT
EXPLANATION
10 INPUT TYPE
RF Xmitter
Enter the input device type as follows:
00 = not used
01 = hardwired
03 = supervised RF transmitter (RF type)
04 = unsupervised RF transmitter (UR type)
05 = RF button-type transmitter (BR type)
06 = serial number polling loop device (SL type)
07 = DIP switch-type polling loop device
08 = right loop of DIP switch type device
Right loops refer to the use of the right loop on a 4190WH Zone Expander Module and/or 4278 PIR, which
allow hardwired devices to be monitored by the polling loop.
If you are programming hardwired or DIP switch polling loop devices, the summary display appears after
completing this entry.
Press [✱] to continue.
3
Input types 4 & 5 are
valid for certain 5800
Series transmitters only
(e.g., 5801, 5802, 5802CP
& 5803).
10 INPUT S/N:
AXXX-XXXX
L
1
For Serial Number entry and Loop Number entry, do one of the following:
a. Transmit two open and close (or close and open) sequences. For a button-type transmitter, press and
release the button, wait approximately 4 seconds, then press and release the button a second time.
OR
b. Manually enter the 7-digit serial number printed on a label on the transmitter, using the Alpha keypad.
Then press the [✱] key, the cursor moves to the “L” position. You can edit the loop number, if necessary.
When the loop number is acceptable, press [✱].
OR
c. Press key [C] to copy the last serial number enrolled (used when programming a transmitter with several
input loops).
Press [✱] to accept.
10 INPUT S/N:
A022-4064
L
1
The cursor will then move to the Loop column (L) with the previously entered/transmitted serial number
displayed.
Enter the loop number (refer to 5800 Series Transmitters Loop Designations below).
To Delete an Existing Serial Number, enter “0“ in the loop number field. The serial number will change to
“0”s.
If “0” was entered in error, simply re-enter the loop number or press [#], and the serial number will return to
the display.
Press [✱] to accept.
10 INPUT S/N:
A022-4064
L
1
The system will then check for a duplicate serial/loop number combination.
If a duplicate serial/loop number combination is found, the keypad will emit a single long beep, and display
the serial number along with a “?” for the loop number, allowing you to re-enter the correct loop number.
If the serial/loop number combination is not a duplicate in the system, a display appears showing the serial
number and loop number entry.
Press [✱] to continue.
– 14 –
5800 Series Transmitters Loop Designations
LOOP 3
LOOP 2
(REED)
LOOP 1
(PRIMARY)
LOOP 2
LOOP 2
(AUX. CENTER)
LOOP 1
5801
ENROLL AS "UR" OR "RF"
LOOP 1
(TERMINALS)
LOOP
1
LOOP 4
YOU MUST
ENROLL THIS
BUTTON
ALTERNATE
POSITION
FOR LOOP 2
5802MN
ENROLL AS "UR" OR "RF"
LOOP 2
(REED)
LOOP
2
(REED)
LOOP 2
LOOP 4
LOOP 1
LOOP 1
(TERMINALS)
LOOP 2
YOU MUST
ENROLL THIS
BUTTON
LOOP 4
LOOP 1
(INTERNAL
SHOCK
SENSOR)
LOOP 3
(TERMINALS)
LOOP 3
(TERMINALS)
5819
ENROLL AS "RF"
LOOP 1
5819S (WHS & BRS)
ENROLL AS "RF"
LOOP 3
••
••••••••
•• ••
••
•
••
5804
ENROLL
AS "BR"
5817
ENROLL AS "RF"
5816MN
ENROLL AS "RF"
LOOP 3
YOU MUST
ENROLL THIS
BUTTON
LOOP 3
(AUX. RIGHT)
SET
HOUSE
CODE
5827
SET HOUSE CODE
5827BD
SET HOUSE CODE
5804BD
ENROLL AS "BR"
LOOP
1
5809
ENROLL AS "RF"
LOOP 2
(REED)
LOOP 1
(MOTION)
LOOP
1
5808
ENROLL AS "RF"
LOOP 1
(TERMINALS)
5816
ENROLL AS "RF"
(Green)
(Red)
(Yellow)
5850 (GBD)
ENROLL AS "RF"
5890
ENROLL AS "RF"
5800_trans_loop-V0
Note: For information on any transmitter not shown above, refer to the instructions accompanying that transmitter for
details regarding loop numbers, etc.
UL
The 5802MN, 5802MN2, 5804, 5804BD, 5814, 5816TEMP, 5819, 5819WHS & BRS, 5827BD,
and 5850 transmitters are not intended for use in UL installations.
PROMPT
EXPLANATION
XMIT TO CONFIRM
PRESS ✱TO SKIP
Confirmation Option: This prompt only appears if you answered “Yes” at the first prompt. The system
enters a confirmation mode so that the operation of the actual programmed input can be confirmed. Activate
the loop input or button that corresponds to this zone. At any time during this step, you may press the [✱] key
on the keypad to save the serial and loop number combination without confirming.
Entd
Rcvd
A022-4063
A022-4064
10 ZT P RC In L
03 1 3C RF 1s
1
If the serial number transmitted does not match the serial number entered, a display similar to the one
at the left appears. If the loop number does not match, it is also displayed.
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display does not appear), press the [#] key twice and then enter or transmit the correct serial number.
If the serial number transmitted does match the serial number entered, the system beeps 3 times and a
summary display appears, showing that zone’s programming. Note that an “s” indicates that a transmitter’s
serial number has been enrolled.
Press [✱] to accept the zone information.
– 15 –
PROMPT
EXPLANATION
ENTER ZONE NO.
00 = QUIT
The system now returns to the “ENTER ZONE NO.” prompt for the next zone.
When all zones have been programmed, enter “00” to quit.
11
After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in
the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information
(zone number, zone type, etc.) relevant to that device.
When you have finished programming all zones, test each using the system’s Test Mode. Do not use the
Transmitter ID Sniffer Mode. The system checks only for transmission of one zone on a particular
transmitter, NOT the zones assigned to each additional loop, and also does not verify polling loop type
zones.
Expert Mode Zone Programming
Expert mode allows you to program zones using the minimum number of screens and keystrokes.
Expert Mode Zone Programming does not provide the capability to program some of the zone’s attributes,
such as Arm w/Fault, Vent Zone, STAY mode, Auto-STAY, Bypass Group, etc. If you want to program a
zone for any of these attributes, you must use Zone Programming.
Enter the Programming mode with [Installer Code] + 8 0 0
Before programming your zones, do the following:
1. Program field 2✱00: Number of Partitions.
2. Enable your RF Receiver in Device Programming menu mode.
To program your zones, press ✱93 to display the "ZONE PROG?" prompt. Enter “0” (NO) to each prompt until the “EXPERT
MODE?” prompt appears.
PROMPT
EXPLANATION
EXPERT MODE?
1 = YES 0 = NO
Press 1 to enter Expert mode.
0
SET TO CONFIRM?
0 = NO 1 = YES
Zn ZT P RC In
01 03 1 10 HW
Zn
10
0
This prompt appears once upon entering Expert Mode.
If you select “Yes,” Confirmation prompts will be displayed after the device’s Serial and Loop numbers have
been entered later.
L
A summary display appears, showing zone 1’s current programming or default values.
-
ZT P RC In L
03 1 10 RF 1s
Enter the desired 2-digit zone number and press [✱].
Note: If you want to exit the Expert mode, enter “00” + [✱].
If an “s” appears after the loop number, it indicates that the transmitter’s serial number has been enrolled.
Use the [D] key to enter and duplicate wireless keys (see “Entering Wireless Keys” later)
– 16 –
PROMPT
EXPLANATION
Zn ZT P RC
10 03 1 10
Enter all zone information except for Loop number, or press “C” to copy the zone information on this screen
from the last saved zone (including Loop).
ZT = Zone Type
P = Partition
RC = Report Code
In = Input Device Type
L = Loop number to which the sensor is connected.
NOTE: Pressing the [C] copies the zone information from the last saved zone, which includes the
input type. Verify this information is correct for this zone.
On this screen:
In L
RF -
•
•
Use the [A] key to move to the right.
Use the [B] key to move to left and to back up to “ZT” field.
Press [✱] to accept the existing or newly-entered zone information.
If you entered RF, BR, UR or SL for the Input Type, this screen displays. Otherwise the summary screen for
the next zone displays.
Enter the 7-digit serial number, using one of the following methods:
a. Transmit two open and close (or close and open) sequences. For a button-type transmitter, press and
release the button, wait approximately 4 seconds, then press and release the button a second time.
OR
b. Manually enter the 7-digit serial number printed on a label on the transmitter, using the alpha keypad.
Then press the [✱] key, the cursor will move to the “L” position. You can edit the loop number, if
necessary. When the loop number is acceptable, press [✱].
OR
c. Press key [C] to copy the last serial number enrolled (used when programming a transmitter with several
input loops).
Remember, you can use the [A] key to move to the right or the [B] key to move to the left.
You can also use the [#] key to back up without saving.
10 INPUT S/N:
L
A XXX-XXXX -
10 INPUT S/N:
A022-4064
L
1
Press [✱] to accept the serial number and advance to the “L” position (if method “a” or “c” was used), then
enter the loop number.
If necessary, press the [#] key to back up without saving, and re-enter or edit the serial number before
pressing [✱] to save
The system checks for a duplicate. If a duplicate serial/loop number combination is found, the keypad will
emit a single long beep, and display the serial number along with a “?” for the loop number, allowing you to
re-enter the correct loop number.
10 INPUT S/N:
A000-0000
L
1
To Delete an Existing Serial Number, enter “0“ in the loop number field. The serial number will change to
“0”s.
If “0” was entered in error, simply re-enter the loop number or press [#], and the serial number will return to
the display.
The prompt to confirm appears. This prompt only appears if you answered “Yes” at the “SET TO
CONFIRM?” prompt.
The system enters a confirmation mode so that the operation of the actual programmed input can be
confirmed. Activate the loop input or button that corresponds to this zone. At any time during this step, you
may press the [✱] key on the keypad to save the serial and loop number combination without confirming.
XMIT TO CONFIRM
PRESS ✱TO SKIP
Entd
Rcvd
Zn
11
A022-4063
A022-4064
ZT
00
P
1
RC
10
1
In L
00 1
If the serial number transmitted does not match the serial number entered, a display similar to the one
at the left appears. If the loop number does not match, it also is displayed.
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display for the next zone does not appear), press the [#] key twice and then enter or transmit the correct
serial number.
Activate the button on the wireless key again after re-entering the serial number.
If the serial number transmitted matches the serial number entered, the system beeps 3 times and
advances to the summary display for the next zone's programming.
After all the zones have been programmed, enter 00 for the zone number to quit.
After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in
the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information
(zone number, zone type, etc.) relevant to that device.
– 17 –
Entering Wireless Keys
If you pressed the D key previously to enter defaults for 5804 and/or 5804BD wireless keys, the following screens appear:
PROMPT
EXPLANATION
FROM TEMPLATE
1–6
1
Enter template number (1–6).
1–3 = 5804 templates; 4–6 = 5804BD templates. See the defaults provided for each template in the chart
that follows these procedures.
Select from templates. Press [✱] to display template (template 1 shown selected).
Note: If necessary, press [#] to back up and re-enter template number.
Press [#] if you want to return to zone attributes screen.
L 01 02 03 04
ZT 23 22 21 23 1
When you press [✱], the selected template is displayed.
Top line of display represents loop numbers; bottom line represents zone type.
Press [✱] to accept template.
PARTITION
Enter partition number for wireless key.
Press [✱] to continue.
1
ENTER ZONE NO
00 = QUIT
24
▲
Example of zone number
suggested by the system.
This indicates that zones
24, 25, 26, and 27 are
available.
24 INPUT S/N
AXXX-XXXX
L
1
The system searches for the highest available, consecutive 4-zone group (the four zones required for the
5804 and 5804BD), and displays the lowest zone number of the group.
If you want to start at a different zone number, enter the zone desired and press [✱].
If that zone number is displayed, the system has the required number of consecutive zones available,
beginning with the zone you entered. If not, the system again displays a suggested zone that can be used.
If the required number of consecutive zones is not available at all, the system will display “00.”
Press [✱] to accept.
To enter the serial number:
Press and release a button on the wireless key.
OR
Manually enter the 7-digit serial number printed on the device’s label.
Press [✱] to accept serial number. The system checks for a duplicate.
If a duplicate exists, a long error beep will sound and the serial number reverts back to all “X”s allowing
you to re-enter the serial number.
Use the [A] key to move forward within the screen, and the [B] key to back up.
XMIT TO CONFIRM
PRESS ✱TO SKIP
If you entered YES previously at the SET TO CONFIRM prompt (see first prompt following entry into the
Expert Programming Mode), the display on the left appears.
To confirm, activate the button on the wireless key that corresponds to this zone.
Entd
Rcvd
If the serial number transmitted does not match the serial number entered, a display similar to the one
at the left appears.
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display does not appear), press the [#] key and then enter the correct serial number.
Activate the button on the wireless key again after re-entering the serial number.
A022-4063
A022-4064
ENTER ZONE NO
00 = QUIT
28
If the serial number transmitted matches the serial number entered, the system will beep 3 times and
revert to the "Start Zone No." prompt and will show the lowest numbered zone of the next available 4-zone
group (4 consecutive zones) that is available for programming.
After all the wireless keys have been entered, enter 000 for the zone number to quit.
After you have enrolled each wireless device, remove ONE of the serial number labels from that device and affix it in
the appropriate column on the worksheets provided later in this Programming Guide; then enter the other information
(zone number, zone type, etc.) relevant to that device.
– 18 –
Wireless Key Default Templates
5804
Template 1
Template 2
Template 3
5804BD
Loop
1
2
3
4
Loop
1
2
3
4
Loop
1
2
3
4
Function
No Response
Disarming
Arm AWAY
No Response
Function
No Response
Disarming
Arm AWAY
Arm STAY
Function
24-Hour Panic
Disarming
Arm AWAY
Arm STAY
Zone Type
23
22
21
23
Zone Type
23
22
21
20
Zone Type
07
22
21
20
Template 4
Template 5
Template 6
– 19 –
Loop
1
2
3
4
Loop
1
2
3
4
Loop
1
2
3
4
Function
No Response
No Response
Arm AWAY
Disarming
Function
No Response
Arm STAY
Arm AWAY
Disarming
Function
24-Hour Panic
Arm STAY
Arm AWAY
Disarming
Zone Type
23
23
21
22
Zone Type
23
20
21
22
Zone Type
07
20
21
22
Alpha Descriptors Programming
You can program a user-friendly English language description/location for all protection zones, relays, keypad panics, polling
loop short, and RF receiver supervision troubles.
Each description can be composed of a combination of words (up to 3) that are selected from a vocabulary of 244 words
stored in memory, and any word can have an "s" or " ’s " added to it.
NOTE: Due to the use of 2-digit zone numbers, the first word of the descriptor is limited to 7 characters if you want it to fit on
the top line of the display.
In addition, up to 20 installer-defined words can be added to those already in memory. Thus, when an alarm or trouble occurs
in a zone, an appropriate description for the location of that zone will be displayed at the keypad.
A custom installer’s message can be programmed for each partition that is displayed when the system is "Ready" (e.g., THE
PETERSONS’).
1. To program alpha descriptors, enter Programming mode, then press #93 to display "ZONE PROG?"
2. Press [0] (NO) twice to display "ALPHA PROG?".
3. Press [1] to enter Alpha Programming.
There are 5 submenu selections that will be displayed one at a time.
Press [1] to select the mode desired.
Press [0] to display the next mode available. The alpha menu selections are:
4.
ZONE DESCRIP?
For entering zone descriptors.
DEFAULT SCREEN?
For creating custom message; displayed when system is ready.
CUSTOM WORD?
For creating custom words for use in descriptors.
PART DESCRIP?
For creating 4-character partition names.
EXIT EDIT MODE?
Press [1] to exit back to #93 Menu Mode.
Refer to the sections that follow for procedures for adding alpha descriptors.
Zone Descriptors
1. Select ZONE DESCRIPTOR mode.
The keypad keys perform the following functions:
[3] Scrolls both alphabet and actual words in ascending alphabetical order.
[1] Scrolls both alphabet and actual words in descending alphabetical order.
[2] Adds or removes an "s" or " 's " to a vocabulary word.
[6] Switches between alphabet and actual word list; used to accept entries.
[8] Saves the zone description in the system's memory.
[#] [#] plus zone number displays the description for that zone.
2. Enter the zone number to which you want to assign a descriptor.
For example, key [✱] 01 to begin entering the description for Zone 1, (key [✱] 02 for Zone 2, [✱] 03 for Zone 3, etc.). The
following is displayed: ✱ ZN 01 A.
Note that the first letter of the alphabet appears after the zone number, and that the zone number is automatically
included with the description.
3. Enter the descriptor for that zone.
Use one of two methods as follows:
(Assume, for example, that the desired description for Zone 1 is BACK DOOR.)
a) Press [#] followed by the 3-digit number of the first word from the fixed dictionary shown later in this section (e.g.,
[0][1][3] for BACK).
Press [6] in order to accept the word and proceed, or press [8] to store the complete descriptor and exit;
or
b) Select the first letter of the desired description (note that "A" is already displayed). Use the [3] key to advance
through the alphabet and the [1] key to go backward.
Press [3] key repeatedly until "B" appears (press [1] to go backwards if you happen to pass it), then press [6] to
display the first available word beginning with “B”.
Press [3] repeatedly to advance through the available words until the word “BACK” is displayed.
To add an "s" or " 's," if you need to, press 2. The first depression adds an "s," the second depression adds
an " 's, " the third depression displays no character (to erase the character), the fourth depression adds an
"s," etc.
– 20 –
4.
5.
6.
7.
Accept the word.
To accept the word, press [6], which switches back to the alphabet list for the next word, or press [8] to store the
complete descriptor and then exit.
Select the next word.
For selection of the next word (DOOR), repeat step 3a (word #057) or 3b, but selecting the word "DOOR.”
To accept the word, press [6], which again switches back to alphabet list.
Store the descriptor.
When all desired words have been entered, press [8] to store the description in memory.
To review the zone descriptors, key [#] plus zone number (e.g., #01).
To edit zone descriptors, key [✱] plus zone number (e.g., ✱01)
Exit Zone Description Mode: enter 00.
Default Screen (Custom Message Display)
Normally, when the system is in the disarmed state, the following display is present on the keypad.
****DISARMED****
READY TO ARM
Part or all of the above message can be modified to create a custom installer message for each partition. For example,
“****DISARMED****” on the first line or “READY TO ARM” on the second line could be replaced by the installation company
name or phone number for service.
Note: There are only 16 character spaces on each of the two lines.
To create a custom display message, proceed as follows:
1. Select Default Screen mode.
The keypad asks for the partition number for this message.
Enter the partition number. Press [✱] to accept entry.
The following display appears:
****DISARMED****
READY TO ARM
2.
3.
4.
A cursor is present at the extreme left of the first line (over the first "star"). Press [6] to move the cursor to the right and [4]
to move the cursor to the left. Press [7] to insert spaces or erase existing characters.
Create the message.
For example, to replace “READY TO ARM” with the message “SERVICE 424-0177,” proceed as follows:
Press [6] to move the cursor to the right, and continue until the cursor is positioned over the first location on the second
line.
Press [3] to advance through the alphabet to the first desired character (in this case, "S"). Press [1] to go backward, when
necessary. When the desired character is reached, press [6].
The cursor then moves to the next position, ready for entry of the next character (in this example, "E"). When the cursor
reaches a position over an existing character, press [3] or [1] to advance or back up from that character in the alphabet.
Proceed in this manner until all characters in the message have been entered.
Save the message.
Store the new display message in memory by pressing [8].
The system asks for a new partition number.
Enter 0 to quit or 1-8 for a new partition number.
Custom Words
Up to 20 installer-defined words can be added to the built-in vocabulary. Each of the 20 "words" can actually consist of several
words, but bear in mind that a maximum of 10 characters can be used for each word string.
1. Select CUSTOM WORD Mode.
The keys perform the following functions:
[3] Advances through alphabet in ascending order.
[1] Advances through alphabet in descending order.
[6] Selects desired letter; moves the cursor 1 space to the right.
[4] Moves the cursor one space to the left.
[7] Inserts a space at the cursor location, erasing any character at that location.
[8] Saves the new word in the system's memory.
[✱] Returns to Description Entry Mode.
– 21 –
2.
3.
4.
5.
6.
7.
Enter the custom word number (01-20) you want to create.
For example, if you are creating the first word (or word string), enter 01; when creating the second word, enter 02, and so
on. A cursor now appears at the beginning of the second line.
Type the word using one of two methods as follows:
a) Press [#], followed by the 2-digit entry for the first letter you would like to display (e.g., 65 for "A").
When the desired character appears, press [6] to select it. The cursor will then move to the right, in position for the
next character. Press [#] plus the 2-digit entry for the next letter of the word.
or
b) Press 3 to advance through the list of symbols, numbers, and letters.
Press 1 to move back through the list.
When you have reached the desired character, press [6] to select it. The cursor then moves to the right, in position
for the next character.
Repeat step 3 to create the desired custom word (or words).
Press [4] to move the cursor to the left if necessary.
Press [7] to enter a blank (or to erase an existing character).
Each word or word string cannot exceed 10 characters.
Save the word by pressing [8].
This returns you to the “CUSTOM WORD?” display. The custom word (or string of words) is automatically added to the
built-in vocabulary at the end of the group of words beginning with the same letter.
Custom words are retrieved as word numbers 250 to 269 for words 1 to 20, respectively, when using method 3a to enter
alpha descriptors.
When using method 3b to enter alpha descriptors, each word appears at the end of the group of words that begin with the
same letter as it does.
Repeat steps 2 through 6 to create up to a maximum of 20 custom words (or word strings).
Exit Custom Word Mode by entering 00 at the “CUSTOM WORD” prompt.
Partition Descriptors
1. Select "Part DESCRIPT." Mode.
The system asks for the partition number desired. Enter the number as a single-key entry 1-8.
2. Follow the same procedure as for custom words.
Note: The partition descriptors are limited to 4 characters (e.g., WHSE for warehouse).
– 22 –
Alpha Descriptor Vocabulary
(For entering alpha descriptors. To select a word, press [#] followed by the word’s 3-digit number.)
NOTE: This vocabulary is not to be used for relay voice descriptors. See the Relay Voice Descriptors section when
programming relay voice descriptors.
000
• 001
• 002
003
004
005
• 006
• 007
008
• 009
010
011
(Word Space)
AIR
ALARM
ALCOVE
ALLEY
AMBUSH
AREA
APARTMENT
ART
ATTIC
AUDIO
AUXILIARY
• 012
• 013
• 014
015
• 016
• 017
• 018
• 019
020
• 021
• 022
023
024
025
• 026
027
BABY
BACK
BAR
BARN
BASEMENT
BATHROOM
BED
BEDROOM
BELL
BLOWER
BOILER
BOTTOM
BOX
BREAK
BUILDING
BURNER
028
029
030
031
032
033
034
035
036
037
038
039
040
041
042
043
044
045
046
047
CABINET
CALL
CAMERA
CAR
CASE
CASH
CCTV
CEILING
CELLAR
CENTRAL
CIRCUIT
CLIP
CLOSED
COIN
COLD
COATROOM
COLLECTION
COMBUSTION
COMPUTER
CONTACT
• 048
049
• 050
051
DAUGHTERS
DELAYED
DEN
DESK
•
•
•
•
• 052
• 053
054
055
056
• 057
058
• 059
• 060
061
• 062
063
• 064
DETECTOR
DINING
DISCRIMINATOR
DISPLAY
DOCK
DOOR
DORMER
DOWN
DOWNSTAIRS
DRAWER
DRIVEWAY
DRUG
DUCT
• 065
066
067
068
• 069
070
• 071
072
EAST
ELECTRIC
EMERGENCY
ENTRY
EQUIPMENT
EXECUTIVE
EXIT
EXTERIOR
• 073
074
075
• 076
• 077
078
• 079
• 080
081
082
• 083
084
• 085
086
087
FACTORY
FAILURE
FAMILY
FATHERS
FENCE
FILE
FIRE
FLOOR
FLOW
FOIL
FOYER
FREEZER
FRONT
FUR
FURNACE
088
• 089
• 090
091
• 092
093
094
102
103
INTERIOR
INTRUSION
104
• 105
JEWELRY
KITCHEN
• 106
• 107
108
• 109
• 110
111
112
• 113
• 114
115
116
117
• 118
LAUNDRY
LEFT
LEVEL
LIBRARY
LIGHT
LINE
LIQUOR
LIVING
LOADING
LOCK
LOOP
LOW
LOWER
• 119
120
121
122
• 123
124
• 125
126
127
128
129
• 130
• 131
132
133
MACHINE
MAGNETIC
MAIDS
MAIN
MASTER
MAT
MEDICAL
MEDICINE
MICROWAVE
MONEY
MONITOR
MOTHERS
MOTION
MOTOR
MUD
• 134
135
NORTH
NURSERY
GALLERY
GARAGE
GAS
GATE
GLASS
GUEST
GUN
• 136
137
• 138
139
• 140
141
142
OFFICE
OIL
OPEN
OPENING
OUTSIDE
OVERFLOW
OVERHEAD
• 095
• 096
097
098
099
HALL
HEAT
HIGH
HOLDUP
HOUSE
100
• 101
INFRARED
INSIDE
143
• 144
145
• 146
147
• 148
149
150
PAINTING
PANIC
PASSIVE
PATIO
PERIMETER
PHONE
PHOTO
POINT
151
152
• 153
154
155
• 156
157
158
159
160
• 161
• 162
163
•
•
•
•
•
•
•
•
•
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
• 199
200
• 201
202
POLICE
POOL
POWER
QUAD
RADIO
REAR
RECREATION
REFRIG
REFRIGERATION
RF
RIGHT
ROOM
ROOF
SAFE
SCREEN
SENSOR
SERVICE
SHED
SHOCK
SHOP
SHORT
SHOW
SIDE
SKYLIGHT
SLIDING
SMOKE
SONIC
SONS
SOUTH
SPRINKLER
STAMP
STATION
STEREO
STORE
STORAGE
STORY
STRESS
STRIKE
SUMP
SUPERVISED
SUPERVISION
SWIMMING
SWITCH
TAMPER
TAPE
TELCO
TELEPHONE
TELLER
TEMPERATURE
THERMOSTAT
TOOL
TRANSMITTER
•
•
•
•
203
TRAP
204
205
206
207
208
209
210
211
212
ULTRA
UP
UPPER
UPSTAIRS
UTILITY
VALVE
VAULT
VIBRATION
VOLTAGE
213
214
215
• 216
• 217
218
• 219
220
221
WALL
WAREHOUSE
WASH
WEST
WINDOW
WINE
WING
WIRELESS
WORK
222
XMITTER
223
YARD
224
• 225
ZONE (No.)
ZONE
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
250
0
1
1ST
2
2ND
3
3RD
4
4TH
5
5TH
6
6TH
7
7TH
8
8TH
9
9TH
Custom Word 1
269
Custom Word 20
to
CHARACTER (ASCII) CHART
32
33
34
35
36
37
38
39
40
41
(space)
!
"
#
$
%
&
’
(
)
42
43
44
45
46
47
48
49
50
51
*
+
,
.
/
0
1
2
3
52
53
54
55
56
57
58
59
60
61
(For Adding Custom Words)
4
62
>
5
63
?
6
64
@
7
65
A
8
66
B
9
67
C
:
68
D
;
69
E
<
70
F
=
71
G
72
73
74
75
76
77
78
79
80
81
H
I
J
K
L
M
N
O
P
Q
82
83
84
85
86
87
88
89
90
R
S
T
U
V
W
X
Y
Z
Notes: This factory-provided vocabulary of words is subject to change.
Bulleted words in bold face type are those that are also available for use by the 4285/4286 VIP Module. If you are
using a VIP Module, and words other than these are selected for alpha descriptors, the Voice Module will not provide
annunciation of those words.
– 23 –
Device Programming
This menu is used to program keypads, receivers, and relay modules, etc.
Device Address 00 is always set as an alpha keypad assigned to Partition 1 with no sounder suppression
options, and these settings cannot be changed.
From Data Field Programming mode, press #93 to display "ZONE PROG?" Press [0] repeatedly to display "DEVICE PROG?"
PROMPT
EXPLANATION
DEVICE PROG?
1=YES 0=NO
Press [1] to enter Device Programming.
DEVICE ADDRESS
01-30, 00=QUIT
0
01
The device address identifies the device to the control. Enter the 2-digit device address number to match
the device’s physical address setting (01-30).
Press [✱] to accept entry.
Select the type of addressable device as follows:
DEVICE TYPE
00
00 = device not used
01 = alpha keypad (6139/6160)
02 = fixed-word keypad (6137/6150)
Press [✱] to accept entry.
03 = RF receiver (5881)
04 = output relay module (4204)
05 = voice (VIP) Module (4285/4286)
Alpha or Fixed-Word Keypad
PROMPT
EXPLANATION
01 CONSOLE PART.
If you selected device type 01 (alpha keypad), or 02 (fixed-word keypad), this prompt appears. Enter the
addressable device’s default partition number (01 to maximum number of partitions programmed for system
in field 2*00). This is the primary partition for the device. Enter 9 to make this keypad a "Master" keypad for
the system.
Press [✱] to accept entry.
1
01 SOUND OPTION
00
Keypads can be individually programmed to suppress arm/disarm beeps, entry/exit beeps and chime mode
beeps. This helps prevent unwanted sounds from disturbing users in other areas of the premises.
Enter a number 00-03 for the keypad sounding suppression options desired for the keypad as follows:
00 = no suppression
01 = suppress arm/disarm & entry/exit beeps
02 = suppress chime mode beeps only
03 = suppress arm/disarm, entry/exit and chime mode beeps
Press [✱] to accept entry.
RF Expander
PROMPT
01 RF EXPANDER
HOUSE I
EXPLANATION
00
If you selected device type 03 (RF receiver), this prompt appears. Enter the 2-digit House ID (00-31). This
is required if you are using a wireless keypad (5827/5827BD).
Press [✱] to accept entry.
VIP Module
PROMPT
EXPLANATION
01 MODULE PART.
If you selected device type 05 (VIP Module) this prompt appears. Enter the partition number 1-8 in which the
module is located.
Press [✱] to accept entry.
Press 00 + [✱] to exit Menu mode.
Press ✱99 to exit Program mode.
1
– 24 –
Relay Programming
The system supports up to 16 relays. Relays can be used to perform many different functions and actions. Each output must
be programmed to begin one of three types of ACTIONS at a designated START event, and end that ACTION at a designated
STOP event. The options used to start and stop these devices are described below, followed by the actual screen prompts
and available entries.
The letter(s) in parentheses after each function described below, such as (A) after ACTION, are those that appear in the
various summary displays of programmed data during programming.
ACTION (A)
The "ACTION" of the device is how the device will respond when it is activated by the "START"
programming. You may want the device to activate momentarily, to pulse on and off continuously, or to
remain activated until some other event occurs to stop it. There are five different action choices:
•
ACTIVATE for 2 SECONDS and then reset.
•
ACTIVATE and REMAIN ACTIVATED until stopped by some other event.
•
PULSE ON and OFF until stopped by some other event (do not use with an FSA device).
•
NO RESPONSE when the device is not used.
START (STT)
The "START" programming determines when and under what conditions the device is activated. The
following START options are available:
1) EVENT (EV) is the condition (alarm, fault, trouble) that must occur to a zone or group of zones (zone
list) in order to activate the device. These conditions apply only when a zone list is used. The different
choices for "EVENT" are listed below and in “Programming Relays” later in this section.
•
ALARM
Action begins upon any alarm in an assigned zone in the zone list.
•
FAULT
Action begins upon any opening of an assigned zone in the zone list.
•
TROUBLE
Action begins upon any trouble condition in an assigned zone in the zone list.
•
NOT USED
Action is not dependent upon one of the above events.
ZONE LIST (ZL) is a group of zones to which the “EVENT” applies in order to activate a particular
device. Note that there are a total of 8 zone lists that can be programmed; when the selected EVENT
(alarm, fault or trouble) occurs in any zone in the selected “Start” ZONE LIST (1-8), activation of the
selected device will START.
2) ZONE TYPE/SYSTEM OPERATION (ZT). If all zones to be used to start the device have the same
response type, and there are no other zones of this type that are not to activate this device, then
“ZONE TYPE” may be used instead of a "ZONE LIST" and "EVENT” to activate the device.
If a system operation, such as “DISARMING” or “ANY FIRE ALARM,” is to activate the device, enter
the appropriate choice under the “ZONE TYPE” option.
The “ZONE TYPE/SYSTEM OPERATION” option functions independently of the “EVENT/ZONE
LIST” combination.
If a specific "ZONE TYPE" is chosen, any zone of that response type going into alarm, trouble, or fault
will cause the device to activate as selected in "ACTION.” If the same “ZONE TYPE” is also chosen for
the STOP programming, any zone of that type that restores will de-activate the device.
If a "SYSTEM OPERATION" is chosen, that operation will cause the device to activate as selected in
"ACTION.” The different choices for "ZONE TYPE" and "SYSTEM OPERATION" are listed in
“Programming Relays” later in this section, and on the Programming Form.
3) PARTITION NO. (P). The device's "Start" ZONE TYPE/SYSTEM OPERATION may be limited to an
occurrence on one partition (1-8), or any partition (0).
STOP (STP):
The "STOP" programming determines when and under what conditions the device is de-activated. The
following options are available:
1). RESTORE ZONE LIST (ZL). If a "ZONE LIST" is used as the “Stop” event, the device de-activates
when all the zones in that list restore from a previous fault, trouble, or alarm condition. This occurs
regardless of what is programmed to "START" the device; therefore, a "RESTORE ZONE LIST" is
normally only used when a "ZONE LIST" is used to start the device.
2). ZONE TYPE/SYSTEM OPERATION (ZT). Instead of using a "RESTORE ZONE LIST," you can select
a specific zone (response) type or system operation action to de-activate the device.
If you choose a specific "ZONE TYPE," any zone of that response type that restores from a previous
alarm, trouble, or fault condition will cause the device to de-activate.
If you choose a "SYSTEM OPERATION," that operation causes the device to de-activate. The
different choices for "ZONE TYPE" and "SYSTEM OPERATION" are listed in “Programming Relays”
later in this section, and in the Programming Form.
3) PARTITION NO. (P). The device's "Stop" Zone Type/System Operation may be limited to an
occurrence on one partition (1-8), or on any partition (0).
The “ZONE TYPE/SYSTEM OPERATION” option functions independently of the
“RESTORE/ZONE LIST” combination.
– 25 –
Relay Devices Programming
From Data Field Programming Mode, press #93 to display the "ZONE PROG?" prompt. Press [0] (NO) to each menu option
until the "RELAY PGM?" prompt appears. Press [1] (YES).
While in this mode, press [✱] to advance to next screen. Press [#] to back up to the previous screen.
PROMPT
EXPLANATION
ENTER RELAY #
(00=QUIT)
01
Enter the relay (output device) identification number 01-16. This is a reference number only, used for
identification purposes. The actual module address and relay number on the module are programmed in the
last two prompts.
Press [✱] to continue.
02 A EV ZL ZT P
STT 0 0 00 00 0
Press [✱] to continue.
02
STOP
The keypad displays a summary STOP screen.
Press [✱] to continue.
A ZL ZT P
0 00 00 0
02 RELAY ACTION
NO RESPONSE
02 START EVENT
NOT USED
0
0
02 START: ZN LIST
0
02 START: ZN TYPE
NO RESPONSE
00
The Relay Action is the way in which the relay will respond when activated by the "start" event. Enter the
desired action for this relay as follows:
0=not used; 1=close for 2 secs.; 2=stay closed; 3=pulse on/off
An output may be activated by an Event/Zone List combination, and/or by a Zone Type/System Operation.
For an Event/Zone List combination, enter the event code as follows:
0=not used; 1=alarm; 2=fault; 3=trouble
If you are not using a Zone List to activate the relay, enter 0.
Press [✱] to continue.
A zone list is a set of zones that can be used to initiate the start or stop relay action. If a zone list is being
used to start this relay action, enter the zone list number, 1-8. If a zone list is not being used, enter 0.
Press [✱] to continue.
A Zone Type/System Operation can be used instead of or in addition to an Event/Zone List combination or
a specific zone to start the relay action. If a Zone Type/System Operation is being used, enter the 2-digit
code as listed in the table that follows.
Press [✱] to continue.
Choices for Start/Stop Zone Types and System Operations:
00 = No Response (Not Used)
23 = No Alarm Response
01 = Entry/Exit #1
31 = End of Exit Time
02 = Entry/exit #2
32 = Start of Entry Time
03 = Perimeter
33 = Any Burglary Alarm
04 = Interior Follower
34 = Code + [#] + 71 Key Entry
05 = Trouble Day/Alarm Night
35 = Code + [#] + 72 Key Entry
06 = 24-Hr. Silent
36 = At Bell Timeout **
07 = 24-Hr. Audible
37 = 2 Times Bell Timeout **
08 = 24-Hr. Auxiliary
38 = Chime
09 = Fire Alarm or Trouble
39 = Fire Alarm
10 = Interior W/Delay
40 = Bypassing
20 = Arming-STAY***
41 = AC Power Fail
21 = Arming-AWAY****
42 = System Battery Low
22 = Disarming (Code + Off)
*
Stop condition only
** Or at disarming, whichever occurs earlier
*** The output also activates when the partition is armed in the INSTANT mode
**** The output also activates when the partition is armed in the MAXIMUM mode
43 = Communication failure
44 = RF Low Battery
45 = Polling Loop Failure
51 = RF Receiver Failure
52 = Kissoff
54 = Fire Zone Reset
55 = Disarm + 1 Minute
56 = XX Minutes (enter XX in field 1*74) *
57 = YY Seconds (enter YY in field 1*75) *
58 = Duress
60 = Audio Alarm Verification (must be
selected for both START and STOP
operation)
If you are using options 56 and/or 57 (usually as the STOP Zone Type), you must program data fields 1*74
and 1*75 for the respective relay timeouts for minutes and seconds.
– 26 –
PROMPT
EXPLANATION
02 START: PARTN
ANY PARTITION
If the starting event will be limited to occurring on a specific partition, enter the partition number (1-8) in
which the start event will occur. Enter 0 for any partition.
Press [✱] to continue.
0
Do not use a zone programmed with an RF Button (Input Type BR) to STOP a relay. The system will not deactivate the relay.
PROMPT
EXPLANATION
02 STOP: ZN LIST
If a zone list is being used to stop this relay action, enter the zone list number, 1-8. The restore of a zone
on the zone list stops the relay. If a zone list is not being used, enter 0.
Press [✱] to continue.
0
02 STOP: ZN TYPE
NO RESPONSE
00
If a Zone Type/System Operation is being used to stop the relay action, enter the 2-digit code listed in the
Choices for Start/Stop System Operation chart.
Press [✱] to continue.
02 STOP: PARTN
ANY PARTITION
0
This is the partition to which the stop condition will be limited. Enter 0 for any partition. Enter 1-8 for specific
partition number.
Press [✱] to continue.
0
Relays may be grouped for common activation by time-driven events (commands 06-10). Enter 0 (no group)
or 1-8 for a specific group number.
Press [✱] to continue.
0
The system may have some devices that are not intended to be under end user control, such as relays
activating fire doors or machinery. Enter 1 if the end user will be restricted from accessing this relay group.
Press [✱] to continue.
02 RELAY GROUP
02 RESTRICTION
1=YES 0=NO
02 RELAY TYPE
ECP
1
02 ECP ADDRESS
00
02 MODULE RELAY#
0
02 HOUSE CODE
A
00
02 UNIT CODE
00
Enter 1 for (ECP) relay modules (4204). Enter 2 for X-10 devices.
Press [✱] to continue.
If you selected 1 (4204), enter the actual module’s address (01-15) as set by its DIP switches.
Press [✱] to continue.
Enter the specific relay number on that module (1-4).
Press [✱] to continue.
The keypad will display the Start and Stop summary screens again.
Press [✱] to continue.
If you selected 2 for X-10 devices, enter the numerical equivalent of the House Code of the device, as
follows:
A=00
D=03
G=06
J=09
M=12
P=15
B=01
E=04
H=07
K=10
N=13
C=02
F=05
I=08
L=11
O=14
Enter the numerical unit code of the X-10 device (00-15).
Press [✱] to continue.
The keypad displays the Start and Stop summary screens again.
Press [✱] to continue.
When all relays have been programmed, enter 00 at the "ENTER RELAY NO." prompt.
– 27 –
If you are defining a zone list, continue to the next section. If not, enter 00 + [✱] at the next two prompts. You will then be
asked "Quit Menu Mode?" Enter 1 for "Yes," 0 for "No." Then enter ✱99 to exit programming completely.
Zone List Programming
After all relays have been programmed, upon entering 00 at the "ENTER RELAY NO." prompt, you are asked to enter a zone
list. If a zone list number was used to start or stop a relay, you must define the zones belonging to that list as follows:
PROMPT
EXPLANATION
ENTER Zn LIST ?
0=QUIT
01 ADD ZONE #
00=QUIT
Enter the zone list number 1-8. Enter 0 to quit.
0
00
Using 2-digit entries, enter each zone to be included in this zone list. Press [✱] after you enter each zone
number.
When you have entered all zones, enter 00.
Press [✱] to continue.
Enter 0 to save this zone list. Enter 1 to delete it.
01 Del Zn LIST ?
1=YES 0=NO
0
01 DEL ZONES ?
1=YES 0=NO
0
Enter 1 to delete one or more zones in that zone list. Enter 0 if no changes are necessary. If you enter 1,
the following screen appears; otherwise, the "Enter Zone LIST" prompt reappears.
01 Zn to DELETE ?
00=QUIT
00
Enter each zone number to be deleted from the zone list, pressing [✱] after each number.
VIEW Zn LIST ?
0=QUIT
This display appears if you pressed 0 at the “Enter Zone LIST” prompt. Enter the zone list number that you
wish to view.
Press [✱] to continue.
0
01 ASSIGNED ZONE
00=QUIT
00
Press [✱] to scroll through all zones in that list. Enter 00 +[✱] to quit.
Press [1] to exit Menu Mode.
Press ✱99 to exit Program Mode.
Relay Voice Descriptors
If you are using the 4285/4286 VIP Module, voice descriptors can be programmed for the 16 outputs. These descriptors are
announced by the voice module when you access the relays via the # 70 Relay Access Mode over the telephone.
Each voice descriptor can consist of up to 3 words selected from the Relay Voice Descriptors and Custom Word Substitutes
Vocabulary list (later in this section).
The index numbers from this vocabulary list are to be used for relay voice descriptors only. For normal
system voice annunciation (e.g., alarms, troubles, status), use the highlighted words in the alpha vocabulary
list in the Alpha Programming part of this guide.
To enter relay voice descriptors, do the following:
1. From Data Field Programming mode, press #93 to display the "ZONE PROG?" prompt.
2. Press [0] (NO) to each menu option until the "RLY VOICE DESCR?" prompt is displayed. Follow the instructions below.
While in this mode, press [✱] to advance to next screen. Press [#] to back up to previous screen.
PROMPT
EXPLANATION
RLY VOICE DESCR?
1=YES 0=NO
Press [1] to program voice descriptors for relays.
ENTER RELAY NO.
00=QUIT
01
0
Enter the 2-digit relay number (01-32) for the relay desired, or enter 00 to quit Relay Voice Descriptor
Programming Mode.
Press [✱]
– 28 –
PROMPT
EXPLANATION
01 ENTER DESC d1
From the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list, enter the 3-digit index
number for the first word of the relay descriptor phrase.
Press [✱] to accept entry.
01 ENTER DESC d2
From the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list, enter the 3-digit index
number for the second word of the relay descriptor phrase. If second word is not desired, press [000].
Press [✱] to accept entry.
01 ENTER DESC d3
From the Relay Voice Descriptors and Custom Word Substitutes Vocabulary list, enter the 3-digit index
number for the third word of the relay descriptor phrase. If third word is not desired, press [000].
Press [✱] to accept entry. The “ENTER RELAY NO.” prompt appears. Enter the next relay number to be
programmed. When you have programmed all output devices, enter 00 to quit.
Enter ✱99 to exit Program Mode.
Relay Voice Descriptors and Custom Word Substitutes Vocabulary
Word
Index
Air ............................ 116
Alarm ....................... 255
And .......................... 067
Apartment ................ 117
Appliances ............... 161
Area ......................... 118
Attic.......................... 119
Baby......................... 120
Back......................... 121
Bar ........................... 122
Basement................. 021
Bathroom ................. 051
Battery...................... 053
Bed .......................... 092
Bedroom .................. 015
Blower...................... 123
Boiler........................ 124
Bright ....................... 162
Building .................... 125
Burglary.................... 039
Call........................... 009
Central ..................... 089
Chime ...................... 054
Closed...................... 126
Computer ................. 127
Console.................... 066
Word
Index
Daughter's ................208
Den...........................052
Detector....................128
Device ......................060
Dim ...........................163
Dining .......................031
Door..........................016
Down ........................008
Downstairs................184
Driveway...................130
Duct ..........................131
Front......................... 087
Garage ..................... 023
Gas .......................... 138
Glass........................ 139
Hall........................... 050
Heat ......................... 010
Factory .....................134
Father's.....................211
Fence .......................135
Fifth ..........................218
Fire ...........................040
First .........................136
Five...........................074
Floor .........................029
Four ..........................073
Fourth .......................217
Foyer ........................137
Word
Index
Off............................ 011
Office ....................... 147
On............................ 058
One.......................... 070
Open........................ 148
Outside .................... 210
Sixth ......................... 219
Smoke...................... 024
Son's ........................ 223
South........................ 155
Stairs........................ 006
Station...................... 156
Storage..................... 157
Sun........................... 154
System ..................... 062
Inside ....................... 209
Kitchen ..................... 022
East ..........................132
Eight .........................077
Eighth .......................221
Equipment ................133
Exit ...........................004
North........................ 146
Not........................... 012
Laundry .................... 140
Left........................... 027
Library ...................... 141
Light ......................... 019
Living........................ 030
Loading .................... 142
Lower ....................... 094
Machine ................... 143
Master ...................... 144
Medical..................... 014
Mother's ................... 212
Motion ...................... 145
Nine.......................... 078
Ninth......................... 222
Word
Index
No ............................ 165
– 29 –
Panic ....................... 013
Partition ................... 090
Patio ........................ 149
Phone ...................... 061
Power ...................... 063
Pump ....................... 166
Rear ........................ 088
Right ........................ 028
Room ....................... 018
's.............................. 007
Second .................... 056
Service..................... 150
Seven ...................... 076
Seventh ................... 220
Shed ........................ 151
Shop ........................ 152
Word
Index
Side ......................... 153
Six ........................... 075
Temperature............. 158
Third......................... 159
Three........................ 072
Tool .......................... 213
Two .......................... 071
Up ............................ 025
Upper ....................... 187
Upstairs .................... 183
Utility ........................ 185
West......................... 215
Window .................... 017
Wing......................... 216
Zero.......................... 069
Zone......................... 002
Custom Word Substitutes for VIP Module Annunciation
A substitute word can be programmed for each of the 20 custom words used in your alpha zone descriptions. The VIP Module
announces this substitute word in place of the custom word that is displayed on the alpha keypad. For example, an alarm
display of "John’s Bedroom" could be announced as "Son’s Bedroom," as there is no annunciation for the custom word "John."
Note that if a substitute word is not assigned, the VIP Module will not annunciate the zone descriptor at all, but will only
annunciate the zone number.
To enter custom word substitutes, do the following:
1. From Data Field Programming Mode, press #93 to display the "ZONE PROG?" prompt.
2. Press [0] (NO) to each menu option until the "CUSTOM INDEX ?" prompt is displayed.
PROMPT
CUSTOM INDEX ?
1=YES 0=NO
EXPLANATION
Enter [1] at this prompt.
0
CUSTOM WORD NO.
00=QUIT
Enter the custom word number (01-20) for which a voice substitute is desired. Enter 00 to quit this
Programming Mode.
Press [✱] to accept entry.
01 ENTER INDEX #
Enter the 3-digit substitute word index number from the Relay Voice Descriptors and Custom Word
Substitutes Vocabulary list in the Relay Voice Descriptors part of this section.
Press [✱] to accept entry.
The "CUSTOM WORD NO." prompt is displayed. Enter the next custom word number to be substituted, or
enter 00 to quit.
– 30 –
System Layout Worksheets
Before programming any security system, you should first define the installation. To help you lay out a partitioned
system, use the following worksheets. This will further simplify the programming process.
PARTITIONS
Partition #
Partition 1
Descriptor
(4-char max)
Prim.
Sub. #
Sec.
Sub. #
Alpha Default Message
(32-character maximum)
Partition 2
Partition 3
Partition 4
Partition 5
Partition 6
Partition 7
Partition 8
Keyswitch Arming Partition Assignment (1-8):
Wireless Keypad Partition Assignment (1-8):
Voice Module Partition Assignment (1-8):
Use Partition Descriptor (yes/no)?
Common Lobby Partition Assignment (1-8):
COMMUNICATION OPTIONS BY PARTITION
Option
Part. 1
Part. 2
Part. 3
Part. 4
Part. 5
Part. 6
Part. 7
Part. 8
Part. 6
Part. 7
Part. 8
Swinger Suppression Count 00-15; 00=no suppression
Cancel Report After Disarm
Dialer Reports for Panic (* + 1)
Dialer Reports for Panic (# + 3)
Dialer Reports for Panic (* + #)
Dialer Reports for Duress
Burglary Alarm Communications Delay (16 sec.)
SYSTEM DEFINITIONS BY PARTITION (enter values or yes/no)
Option
Part. 1
Part. 2
Entry Delay #1 (00, 30-225 seconds):
Exit Delay #1 (00, 45-225 seconds):
Entry Delay #2 (00, 30-225 seconds):
Exit Delay #2 (00, 45-225 seconds):
Quick Arming
Multiple Alarms per Arming
Console Panic for Zone 95 (* + 1)
Console Panic for Zone 96 (# + 3)
Console Panic for Zone 99 (* + #)
Allow Sign-on (GOTO function)
Non-Bypassable Zone*
Sounder Timeout Duration for Bell (2 min. increments)
Console Annunciation During Entry**
Console Annunciation During Exit
Confirmation of Arming Ding for Bell
Chime on Bell
Access Control Relay (field 1*76)
Affects Lobby (check partitions that apply)
Arms Lobby (check partitions that apply)
*Can be any zone 01-86. **no= 3 beeps
yes=continuous
– 31 –
Part. 3
Part. 4
Part. 5
PRINTER OPTIONS
EVENT LOG TYPES
Option
12- or 24-hour Time format
Printer On-Line (yes/no)
No
Yes
Alarm
Trouble
1200 or 300 baud Printer Baud Rate
Bypass
Open/Close
System
DEVICES (keypads, 4204, rf receivers, vip module)
Addr
00.
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
Type
Part
Sound Opt
House ID
Device Types:
00 = Device Not Used
01 = Alpha Keypad
02 = Fixed-Word Keypad
03 = RF Receiver
04 = Output Relay Module
05 = Voice Module
NOTE:
Address 04 must be used for the
Voice Module, if used.
Console Sounder Options:
0 = No Suppression
1 = Suppress Arm/Disarm and Entry/Exit Beeps
2 = Suppress Chime Mode Beeps Only
3 = Suppress Arm/Disarm, Entry/Exit and Chime
Mode Beeps
ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 1 & 2
4-digit
Security
Code
Access
Group
0; 1-8
2-Digit
User #
Auth.
Level
Partition 1
Open/
Close
RF Key
Global
Arm
– 32 –
2-Digit
User #
Auth.
Level
Partition 2
Open/
Close
RF Key
Global
Arm
ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 3 & 4
4-digit
Security
Code
Access
Group
0; 1-8
4-digit
Security
Code
Access
Group
0; 1-8
4-digit
Security
Code
Access
Group
0; 1-8
2-Digit
User #
Auth.
Level
Partition 3
Open/
Close
RF Key
Global
Arm
2-Digit
User #
Auth.
Level
Partition 4
Open/
Close
RF Key
Global
Arm
RF Key
Global
Arm
RF Key
Global
Arm
ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 5 & 6
2-Digit
User #
Auth.
Level
Partition 5
Open/
Close
RF Key
Global
Arm
2-Digit
User #
Auth.
Level
Partition 6
Open/
Close
ACCESS CODES & USER DEFINITIONS FOR PARTITIONS 7 & 8
2-Digit
User #
Auth.
Level
Partition 7
Open/
Close
RF Key
Global
Arm
2-Digit
User #
Authority Levels: 1=Master (arm, disarm, bypass, and/or modify lower level users)
2=Manager (arm, disarm, bypass, and/or modify lower level users)
3=Operator A (arm, disarm, bypass)
4=Operator B (arm, disarm)
5=Operator C (arm, disarm only if system was armed with this code)
6=Duress code (arm, disarm, triggers silent panic alarm)
— 33 —
Auth.
Level
Partition 8
Open/
Close
— 34 —
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Zone No.
Zone Type
Part 1-8
Input Type
Serial # / Loop
Rpt. Code
ZONE DEFINITION FOR ZONES 01-25
Zone Information (part numbers) & Alpha Descriptor (3
words max.)
— 35 —
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
Zone No.
Zone Type
Part 1-8
Input Type
Serial # / Loop
Rpt. Code
ZONE DEFINITION FOR ZONES 26-50
Zone Information (part numbers) & Alpha Descriptor (3
words max.)
— 36 —
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
Zone No.
Zone Type
Part 1-8
Input Type
Serial # / Loop
Rpt. Code
ZONE DEFINITION FOR ZONES 51-75
Zone Information (part numbers) & Alpha Descriptor (3
words max.)
— 37 —
86
85
84
83
82
81
80
79
78
77
76
Zone No.
Zone Type
Part 1-8
Input Type
Serial # / Loop
Rpt. Code
ZONE DEFINITION FOR ZONES 76-86
Zone Information (part numbers) & Alpha Descriptor (3
words max.)
ZONE DEFINITIONS FOR KEYPAD PANIC ZONES 95, 96, & 99
Enter yes/no for each partition-field *22
Zone
No.
Zone
Type
1
2
3
4
5
6
7
8
Report
Code
Zone Information (part numbers) &
Alpha Descriptor (3 words max.)
95
96
99
ZONE DEFINITIONS FOR SYSTEM ZONES; 88; 89, 90, 91, 97 & 98
Zone
No.
Zone
Type
Zone Information (part numbers)
&
Alpha Descriptor (3 words max.)
Report
Code
88
89
90
91
97
98
Zone Types:
00=zone not used
01=entry/exit 1
02=entry/exit 2
03=perimeter
04=interior (follower)
05=day/night burglary
06=24-hour silent
07=24-hour audible
08=24-hour auxiliary
09=supervised fire
10=interior (delay)
20=arm stay
21=arm away
22=disarm
23=no alarm response
Input Types:
00=not used
01=hardwired
03=supervised RF transmitter
04=unsupervised RF transmitter
05=RF button transmitter
06=serial number polling loop
07=Dip switch-type polling loop
08=right loop dip switch polling loop
— 38 —
Relay Devices Worksheets
Applicable only if relays (4204), or X-10 devices are used.
Relays are programmed in the #93 Menu Mode in the Relay Programming Section. Fill in the required data on the
worksheet below and follow the procedure in the Installation and Setup Guide as you enter the data during the displays
and prompts that appear in sequence.
Notes: 1. For 4204 the Device Programming section must be programmed for the device address. Set the DIP
switches on the device for that address.
2. For X-10 devices, use the 1361X10 transformer in place of the transformer that comes in the box with the
control panel.
S T A R T
OUTPUT
DEV #
A
EV/ZL
ZT / P
S T O P
ZL
ZT / P
Relay
Group
Restrict
1=4204
2=X-10
Dev Add 4204
or House Code
for X-10
Relay # for
4204 or
Unit Code for
X-10
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
A =
EV =
ZL =
DEVICE ACTION
EVENT
ZONE LIST
0 = No Response; 1 = Close for 2 sec; 2 = Close and stay closed; 3 = Pulse on and off
0 = Not used; 1 = Alarm; 2 = Fault; 3 = Trouble; 4 = Restore
1-8, 0 = Not Used
"START" ZONE LIST: Upon alarm, fault, trouble or restore of ANY zone in this list, device
action will START.
"STOP" ZONE LIST:
Upon restore of ALL zones on this list, device action will STOP. It
need not be same list as used for START.
— 39 —
ZT =
ZONE TYPE/SYSTEM OPERATION
Choices for Start/Stop Zone Types and System Operations:
00 = No Response (Not Used)
23 = No Alarm Response
43 = Communication failure
01 = Entry/Exit #1
31 = End of Exit Time
44 = RF Low Battery
02 = Entry/exit #2
32 = Start of Entry Time
45 = Polling Loop Failure
03 = Perimeter
33 = Any Burglary Alarm
51 = RF Receiver Failure
04 = Interior Follower
34 = Code + [#] + 71 Key Entry
52 = Kissoff
05 = Trouble Day/Alarm Night
35 = Code + [#] + 72 Key Entry
54 = Fire Zone Reset
06 = 24-Hr. Silent
36 = At Bell Timeout **
55 = Disarm + 1 Minute
07 = 24-Hr. Audible
37 = 2 Times Bell Timeout **
56 = XX Minutes (enter XX in field 1*74) *
08 = 24-Hr. Auxiliary
38 = Chime
57 = YY Seconds (enter YY in field 1*75) *
09 = Fire Alarm or Trouble
39 = Fire Alarm
58 = Duress
10 = Interior W/Delay
40 = Bypassing
60 = Audio Alarm Verification (must be
selected for both START and STOP
20 = Arming-STAY***
41 = AC Power Fail
operation)
21 = Arming-AWAY****
42 = System Battery Low
22 = Disarming (Code + Off)
NOTE: Any zone in "ZT" for Start, going into alarm, fault, or trouble will activate the relay.
Any zone in "ZT" for Stop, that restores will stop the relay action.
*
Stop condition only
** Or at Disarming, whichever occurs earlier
*** The output also activates when the partition is armed in the INSTANT mode
**** The output also activates when the partition is armed in the MAXIMUM mode
P=
PARTITION No. 1-8, 0 = Any
ZONE LISTS FOR OUTPUT DEVICES – Programmed in the #93 Menu Mode in the Output Programming Section. Fill in the
required data on the worksheet below and follow the procedure shown earlier in this Programming Guide as you enter the
data during the displays and prompts that appear in sequence. Up to 8 zone lists may be created
Note: Record desired zone numbers below. More or fewer boxes than shown may be needed, as any list may include any or
all of system's zone numbers.
Zone List 1: Started or stopped by zone numbers (enter 00 to end entries).
Zone List 2: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 3: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 4: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 5: Started or stopped by zone numbers (enter 00 to end entries).
Zone List 6: Started or stopped by zone numbers (enter 000 to end entries).
— 40 —
Zone List 7: Started or stopped by zone numbers (enter 000 to end entries).
Zone List 8: Started or stopped by zone numbers (enter 000 to end entries).
Scheduling Menu Prompts
To program schedules, enter Scheduling program mode by pressing [User Code] + # + 80 to display the first choice of the
menu driven programming functions. NOTE: Only users with an Installer or Master level user code may enter the #80 mode.
Press 0 (NO) or 1 (YES) in response to the displayed menu selection. Pressing 0 will display the next choice in sequence.
Menu selections are as follows:
PROMPT
EXPLANATION
Time Window ?
1 = YES 0 = NO
0
O/C Schedules ?
1 = YES 0 = NO
0
For defining the daily open and close schedules for the 8 partitions. Each partition can be programmed with
an opening and closing window for each day of the week and holidays.
For defining up to 16 holidays for which partitions they apply.
Holidays ?
1 = YES 0 = NO
0
Timed Events ?
1 = YES 0 = NO
0
Access Sched. ?
1 = YES 0 = NO
For defining up to 20 time windows each with a start and a stop time programmed by entering the hours and
minutes.
0
For defining up to 20 time driven events with the following parameters:
•
Time window
•
Action desired
•
Action specifier
•
Activation time
•
Days of the week
For defining the limitation of access schedules for the user codes. Each schedule can be programmed with
two window for each day of the week and holidays
#80 & #81 MENU MODE KEY COMMANDS
The following is a list of commands used while in the Menu mode.
#80 or #81
Enters Menu mode
[ 4]
Serves as ENTER key. Press to have keypad accept entry.
[#]
Backs up to previous screen.
0
Press to answer NO.
1
Press to answer YES.
01-09
00
All data entries are either 2-digit entries.
Exits Menu mode, returns to normal operation mode when entered at the first question for each category.
— 41 —
Scheduling Worksheets
Time Windows Definitions Worksheet. The system provides 20 time windows that are defined with start and stop times.
They are programmed in the #80 Menu Mode. Fill in the required data on the worksheet below and follow the procedure in
the installation instructions as you enter the data during the displays and prompts that appear in sequence.
Time Window
Start Time
Stop Time
Number
(HH:MM)
(HH:MM)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
(Keep this worksheet handy, as you will be asked for a given time window number later in this section).
Because the time windows are shared among all partitions, it is important to make sure that
changing a time window does not adversely affect desired actions in other partitions.
Daily Open/Close Schedule Worksheet: Using the time windows previously defined, fill in the required data on the
worksheet below and follow the procedure in the installation instructions as you enter the data during the displays and
prompts that appear in sequence.
Part
Mon
Op
Cl
Tues
Op
Cl
Wed
Op
Cl
Thur
Op
Cl
1
2
3
4
5
6
7
8
— 42 —
Fri
Op
Cl
Sat
Op
Cl
Sun
Op
Cl
Hol
Op
Cl
Holiday Schedule Worksheet: The system provides up to 16 holidays that can be assigned for the system. Each holiday
can be assigned to any combination of partitions. Fill in the required data on the worksheet below and follow the procedure in
the installation instructions as you enter the data during the displays and prompts that appear in sequence.
HOL
Partition
Month/Day
1
/
2
/
3
/
4
/
5
/
6
/
7
/
8
/
9
/
10
/
11
/
12
/
13
/
14
/
15
/
16
/
1
2
3
4
5
6
7
8
Time-Driven Event Worksheet: The system provides up to 20 time-driven events that can be programmed for the system.
Fill in the required data on the worksheet below and follow the procedure in the installation instructions as you enter the data
during the displays and prompts that appear in sequence.
Sched
Num.
1
Time
Window
Day(s)
M T W T F S S H
Action
Desired
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
— 43 —
Action
Specifier
Activation
Time
Below is a list of the "Action" codes (desired actions) used when programming time-driven events. Note that these codes are
independent of the "relay codes" programmed during the #93 Menu Mode–Relay Programming mode. If using Time Driven
Events, the following menu items must first be programmed using #93 Menu Mode - Relay Programming:
ECP Address
Relay No.
House Code
Unit Code
Enter Relay No. (reference identification number)
Relay Group
(if applicable)
Restriction
Relay Type
(4204 or X-10)
(4204)
(4204)
(X-10)
(X-10)
Relay commands:
Action Specifier for commands 01-05 is Relay No.; Action Specifier for commands 06-10 is Relay Group No.
01 = Relay On
02 = Relay Off
03 = Relay Close for 2 seconds
04 = Relay Close XX minutes (field 1*74)
05 = Relay Close YY seconds (field 1*75)
06 = Relay Group On
07 = Relay Group Off
08 = Relay Group Close for 2 seconds
09 = Relay Group Close XX minutes (field 1*74)
10 = Relay Group Close YY seconds (field 1*75)
Arm/Disarm commands:
Action Specifier for commands 20-24 is Partition(s). Activation times 1 (Beginning), 2 (End), 3 (During) are the only valid
choices for auto-arming and disarming functions.
20 = Arm-Stay
21 = Arm Away
22 = Disarm
23 = Force Arm Stay (Auto-bypass faulted zns)
24 = Force Arm Away (Auto-bypass faulted zns)
Bypass commands:
Action Specifier for commands 30-31 is Zone List #, Activation times 1 (Beginning), 2 (End), 3 (During) are the only valid
choices for bypass commands.
30 = Auto bypass - Zone list
31 = Auto unbypass - Zone list
Open/Close Windows:
Action Specifier for commands 40-41 is Partition(s), and for 42 is Access Group. Activation time 3 (During) are the only valid
choices for these commands.
40 = Enable Opening Window
41 = Enable Closing Window
42 = Enable Access Window
Activation time:
Refers to when the action is to take place relative to the time window.
1 = Beginning of time window
2 = End of time window
3 = During time window active period only (On at beginning of window, off at end).
4 = Beginning and end of time window
Limitation of Access Worksheet The system provides up to 8 Access Schedules that can be programmed for the system.
Fill in the required data on the worksheet below and follow the procedure in the installation instructions as you enter the data
during the displays and prompts that appear in sequence.
Acc
Sch
Mon
W1
W2
Tues
W1
W2
Wed
W1
W2
Thurs
W1
W2
1
2
3
4
5
6
7
8
— 44 —
Fri
W1
Sat
W2
W1
W2
Sun
W1
W2
Hol
W1
W2
Temporary Schedule #81 Menu Mode. The system provides a Temporary Schedule for each partition. Enter the temporary
scheduling mode by pressing [Installer Code] + [#] + [81]. Fill in the required data on the worksheet below and follow the
procedure in the installation instructions as you enter the data during the displays and prompts that appear in sequence.
Partition/Windows
1
Mon
Tue
Wed
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
2
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
3
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
4
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
5
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
6
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
Start Time
HH:MM
Stop Time
HH:MM
— 45 —
Thu
Fri
Sat
Sun
Partition/Windows
7
Mon
Tue
Wed
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
8
Start Time
HH:MM
Stop Time
HH:MM
Disarm Window
Start Time
HH:MM
Stop Time
HH:MM
Arm Window
Start Time
HH:MM
Stop Time
HH:MM
— 46 —
Thu
Fri
Sat
Sun
RED (+)
CHARGING
VOLTAGE
13.7VDC
See
Installation
Instructions for
required
capacity
Connect to
24hr. 120VAC,
Replace
60 Hz Outlet
every
3 years
BLK (–)
— 47 —
3
SIREN
–
BELL
+
2
5
Blk
–
7
Grn
Yel
9
8
–
For Household Fire Installations,
supervise alarm sounder output (Note 5)
and limit combined alarm sounder,
aux power and polling loop current to 750mA.
SMOKE
2k EOLR
(note 1,2)
N.O.
–
11
ZONE 1
N.C.
+
10
2k EOLR
(note 1)
N.O.
N.C.
–
16
N.C.
2k EOLR
(note 1)
N.O.
N.O.
N.C.
+
–
19
GLASS
BREAK
–
24
+
N.C.
N.C.
+
23
–
26
27
28
DOC LOAD NO.: 5
EARTH GROUND
Connect to good earth
ground to maintain immunity to transients.
See Instructions for
proper grounding.
THIS EQUIPMENT SHOULD BE INSTALLED
IN ACCORDANCE WITH THE NATIONAL
FIRE PROTECTION ASSOCIATION'S
STANDARD 72, CHAPTER 2 (NATIONAL FIRE
PROTECTION ASSOC., BATTERYMARCH
PARK. QUINCY, MA. 02269). PRINTED
INFORMATION DESCRIBING PROPER
INSTALLATION, OPERATION, TESTING,
MAINTENANCE, EVACUATION PLANNING
AND REPAIR SERVICE IS TO BE
PROVIDED WITH THIS EQUIPMENT.
WARNING: TO PREVENT
RISK OF ELECTRICAL
SHOCK, DISCONNECT
TELCO JACK BEFORE
SERVICING THIS PANEL.
30
CONNECTION OF THE FIRE ALARM SIGNAL
TO A FIRE ALARM HEADQUARTERS OR A
CENTRAL STATION SHALL BE PERMITED
ONLY WITH THE APPROVAL OF THE LOCAL
AUTHORITY HAVING JURISDICTION. THE
BURGLAR ALARM SIGNAL SHALL NOT BE
CONNECTED TO A POLICE EMERGENCY
NUMBER.
V50P_PUL-SOC-V1
THIS DEVICE COMPLIES WITH PART 15 OF
FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.
COMPLIES WITH FCC RULES, PART 68
FCC REGISTRATION NO. AC398U-68192-AL-E
RINGER EQUIVALENCE: 0.7B
USE UL LISTED ENERGY CABLE FOR ALL CONNECTIONS
4190
SN
4192SD
SMOKE
29
Incoming
Phone Line
Telephone connections
using Ademco No. 620
RJ31X direct connect
cord.
Handset
4208U
25
Polling loop rating: 64mA max. See
Installation Instructions for maximum
number of devices supported and
maximum wire run length.
2k EOLR
(note 1,4)
N.O.
22
ZONE 8 ZONE 9
21
+
N.C.
2k EOLR
(note 1,3)
N.O.
N.C.
+
20
ZONE 6 ZONE 7
18
2k EOLR
(note 1)
+
17
ZONE 4 ZONE 5
15
+
2k EOLR
(note 1)
N.O.
N.C.
+
14
Zone resistance (Excluding EOLR):
ZONE 1,8: 100 OHMS MAXIMUM
ALL OTHER ZONES: 300 OHMS MAXIMUM
Zone response time:
ZONES 1-8: 350mSec-500mSec
ZONE 9: Programmable for
Fast: 10mSec-15mSec
Normal: 350mSec-500mSec
(default response)
–
13
ADEMCO VISTA-50P/VISTA-50PUL
SUMMARY OF CONNECTIONS
Burg.
Usage
Fire
Usage
2k EOLR
(note 1)
N.O.
N.C.
+
12
ZONE 2 ZONE 3
Red Jumper
(note 1)
ALL CIRCUITS ARE
POWER LIMITED
See Installation Instructions
for max. # of keypads
and for max. wire run length.
REMOTE KEYPAD/DEVICES
(Addressable keypads) only
Red
+
6
AUXILARY POWER OUTPUT
9.6VDC - 13.8VDC,
750mA maximum
Note: Include current drawn
by keypads and polling loop
devices when making
auxiliary power calculations.
+
4
ALARM SOUNDER OUTPUT
10VDC - 13.8VDC, 1.7A max
NOTE:
WHEN POWERING UP THE PANEL,
PLUG THE TRANSFORMER IN BEFORE
CONNECTING THE BATTERY.
TRANSFORMER
16.5VAC, 40VA
ADEMCO No.1361
(IN CANADA USE
No. 1361CN)
OR 1361X10
IF X-10 DEVICES
WILL BE USED
1
NO
CONNECTION
3. Zone 7 may be used for remote keyswitch
arming/disarming. See Installation and Setup Guide
for wiring instructions.
Data in
BATTERY
TABS
LATCHING TYPE GLASS
BREAK DETECTOR LOOP
Connect to
12VDC,
4AH - 17.2AH
SEALED LED
ACID BATTERY
Data out
WEEKLY TESTING IS REQUIRED TO ENSURE PROPER OPERATION OF THIS SYSTEM.
Programmable Response
(Fast/Normal) Loop
Blue
Jumper
(note 5)
2-WIRE SMOKE
DETECTOR LOOP
(Also supports NO/NC Burg contacts)
J7 Header
J8 Header
MAKE CONNECTIONS USING
No. 4142TR CABLE
Optional programming:
1. Not Used
1. I n 2 (Printer DTR)
Out 1: Open/close or keypad-like sounding
2. Ground
2. GroundOut 2: Armed LED
3. Out 1 (Ground Start) 3. In 3 (1361X10 sync)
Out 4: Ready LED
4. In 4 (1361X10 sync)
4. GroundJ8
Ratings for Out 1:
5. Ground
5. Out 2 (fire)
6. Out 5 (1361X10 data) Active: 10VDC-13.8VDC through 4k OHMS
6. Ground1 2 3 4 5 6 7 8 9
Not
Active:
100
OHMS
to
ground
7. Out 3 (burg/aud. panic) 7. Out 6 (Printer RXD)
Ratings for out 2-4:
8. Ground
8. Ground
Active: 10VDC-13.8VDC through 5k OHMS
9. Ground
9. Out 4 (silent panic/
Not Active: 1k OHMS to ground
J7
duress)
(Refer to Installation Instructions for information concerning Direct Wire
1 2 3 4 5 6 7 8 9
Downloading and printer connections using the 4100SM Serial Module.)
POLLING LOOP
4. Zone 8 supports 2-wire latching type glass break detectors.
1. Zone 1 may be selected for EOLR supervised
See Installation and Setup Guide for recommended type
or normally closed (no EOLR) operation via
and maximum number of detectors supported.
cut jumper. (Cut red jumper for normally closed
operation. Do not cut for Fire Usage). Zones 2-8
5. Cut blue jumper to disable supervision of alarm sounder output.
may be selected for either operation via program
Leave jumper intact to supervise output. (See Installation and
field *41.
Setup Guide for Programming and Wiring Instructions).
2. Zone 1 supports 2-wire smoke detectors.
See Installation and Setup Guide for recommended
type and maximum number of detectors supported.
(B TIP
RO
WN
)
R
(G ING
RA
Y)
NOTES:
(G TIP
RE
EN
)
RI
(R NG
ED
)
WARNING: OWNER'S INSTRUCTION NOTICE NOT TO BE REMOVED
VISTA-50P/VISTA-50PUL Summary of Connections Diagram
165 Eileen Way, Syosset, New York 11791
Copyright © 2004 Honeywell International, Inc.
www.honeywell.com/security
¬9,67$3359l
VISTA50P-PRV2 5/04 Rev. A
Download PDF