Unitary products group | PT9-UP | Installation manual | Unitary products group PT9-UP Installation manual

INSTALLATION MANUAL
HIGH EFFICIENCY
TUBULAR HEAT EXCHANGER SERIES
EFFICIENCY
RATING
CERTIFIED
MODELS: PT9 / FC9T / FL9T
(Two Stage Upflow)
40 - 120 MBH INPUT
(11.7 - 35.1 KW) INPUT
This product was manufactured
in a plant whose quality system
is certified/registered as being
in conformity with ISO 9001.
TABLE OF CONTENTS
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
DUCTWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
GAS PIPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ELECTRICAL POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
COMBUSTION AIR AND VENT SYSTEM . . . . . . . . . . . . . . . . . . . . . .9
CONDENSATE PIPING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
SAFETY CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
START-UP AND ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . .17
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
LIST OF FIGURES
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Furnace Base Rectangular Blockoff Panel . . . . . . . . . . . . . . . . . . . . . 5
Gas Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Gas Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Line Wiring Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Single Stage Heat Thermostat Connections . . . . . . . . . . . . . . . . . . . . 8
Single Stage Heating and Two-Stage Cooling Thermostat
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Two Stage Heating and Two-Stage Cooling Thermostat Connections 8
Accessory Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Home Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Termination Configuration - 1 Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Termination Configuration - 2 Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Termination Configuration - 2 Pipe Basement . . . . . . . . . . . . . . . . . . 12
Double Horizontal Sealed Combustion Air and Vent Termination . . .13
Double Vertical Sealed Combustion Air and Vent Termination . . . . .13
External Horizontal Vent Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Sealed Combustion Air Intake Connection and Vent Connection . . .13
Combustion Airflow Path Through The Furnace Casing
to the Burner Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Outside and Ambient Combustion Air . . . . . . . . . . . . . . . . . . . . . . . . .15
Attic and Crawl Space Combustion Air Termination . . . . . . . . . . . . . .16
Condensate Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Pressure Switch Tube Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Gas Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Reading Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Furnace Control Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
LIST OF TABLES
Unit Clearances to Combustibles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Minimum Duct Sizing For Proper Airflow . . . . . . . . . . . . . . . . . . . . . . . 4
Round Duct Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Filter Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Inlet Gas Pressure Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
High Altitude Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical and Performance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Combustion Air Intake and Vent Connection Size at Furnace
(All Models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Combustion Air Supply and Vent Piping . . . . . . . . . . . . . . . . . . . . . . .10
Estimated Free Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Free Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Unconfined Space Minimum Area in Square Inch . . . . . . . . . . . . . . .14
Inlet Gas Pressure Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Nominal Manifold Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Blower Performance CFM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Filter Performance - Pressure Drop Inches W.C. and (kPa) . . . . . . . .21
SECTION I: SAFETY
This is a safety alert symbol. When you see this symbol on
labels or in manuals, be alert to the potential for personal
injury.
Understand and pay particular attention to the signal words DANGER,
WARNING, or CAUTION.
DANGER indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.
CAUTION indicates a potentially hazardous situation, which, if not
avoided may result in minor or moderate injury. It is also used to
alert against unsafe practices and hazards involving only property damage.
Improper installation may create a condition where the operation of
the product could cause personal injury or property damage.
Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual
for assistance or for additional information, consult a qualified contractor, installer or service agency.
This product must be installed in strict compliance with the installation instructions and any applicable local, state, and national codes
including, but not limited to building, electrical, and mechanical
codes.
035-20417-001 Rev. C (0904)
035-20417-001 Rev. C (0904)
SPECIFIC SAFETY RULES AND PRECAUTIONS
1.
Only Natural gas or Propane (LP) gas are approved for use with
this furnace. Refer to the furnace rating plate or Section IV of
these instructions.
2.
Install this furnace only in a location and position as specified in
SECTION I of these instructions.
3.
A gas-fired furnace for installation in a residential garage must be
installed as specified in SECTION I of these instructions.
4.
Provide adequate combustion and ventilation air to the furnace
space as specified in SECTION VII of these instructions.
5.
Combustion products must be discharged outdoors. Connect this
furnace to an approved vent system only, as specified in SECTION VII of these instructions.
•
•
•
•
•
•
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warnings exactly could result in serious
injury, death or property damage.
Never test for gas leaks with an open flame. Use a commercially
available soap solution made specifically for detection of leaks to
check all connections. A fire or explosion may result causing property damage, personal injury or loss of life.
6.
Tests for gas leaks as specified in SECTION XI of these instructions.
7.
Always install the furnace to operate within the furnace’s intended
temperature rise range. Only connect the furnace to a duct system
which has an external static pressure within the allowable range,
as specified on the furnace rating plate.
8.
When a furnace is installed so that supply ducts carry air circulated
by the furnace to areas outside the space containing the furnace,
the return air shall also be handled by duct(s) sealed to the furnace casing and terminating outside the space containing the furnace.
9.
The furnace is not to be used for temporary heating of buildings or
structures under construction.
10. When installed in a Non-HUD-Approved Modular Home or building
constructed on-site, combustion air shall not be supplied from
occupied spaces.
11. The size of the unit should be based on an acceptable heat loss
calculation for the structure. ACCA, Manual J or other approved
methods may be used.
SAFETY REQUIREMENTS
•
•
•
•
2
This furnace should be installed in accordance with all national
and local building/safety codes and requirements, local plumbing
or wastewater codes, and other applicable codes. In the absence
of local codes, install in accordance with the National Fuel Gas
Code ANSI Z223.1/NFPA 54, National Fuel Gas Code, and/or
CAN/CGA B149.1 Natural Gas and Propane Installation Code
(latest editions). Furnaces have been certified to the latest edition
of standard ANSI Z21-47 • CSA 2.3.
Refer to the unit rating plate for the furnace model number, and
then see the dimensions page of this instruction for return air plenum dimensions in Figure 1. The plenum must be installed
according to the instructions.
Provide clearances from combustible materials as listed under
Clearances to Combustibles.
Provide clearances for servicing ensuring that service access is
allowed for both the burners and blower.
•
•
These models ARE NOT CSA listed or approved for installation
into a HUD Approved Modular Home or a Manufactured
(Mobile) Home.
This furnace is not approved for installation in trailers or recreational vehicles.
Failure to carefully read and follow all instructions in this
manual can result in furnace malfunction, death, personal
injury and/or property damage.
Furnaces for installation on combustible flooring shall not be
installed directly on carpeting, tile or other combustible material
other than wood flooring.
Check the rating plate and power supply to be sure that the electrical characteristics match. All models use nominal 115 VAC, 1
Phase, 60-Hertz power supply. DO NOT CONNECT THIS APPLIANCE TO A 50 HZ POWER SUPPLY OR A VOLTAGE ABOVE
130 VOLTS.
Furnace shall be installed so the electrical components are protected from water.
Installing and servicing heating equipment can be hazardous due
to the electrical components and the gas fired components. Only
trained and qualified personnel should install, repair, or service
gas heating equipment. Untrained service personnel can perform
basic maintenance functions such as cleaning and replacing the
air filters. When working on heating equipment, observe precautions in the manuals and on the labels attached to the unit and
other safety precautions that may apply.
These instructions cover minimum requirements and conform to
existing national standards and safety codes. In some instances
these instructions exceed certain local codes and ordinances,
especially those who have not kept up with changing residential
and non-HUD modular home construction practices. These
instructions are required as a minimum for a safe installation.
COMBUSTION AIR QUALITY
(LIST OF CONTAMINANTS)
The furnace will require OUTDOOR AIR for combustion when the furnace is located in any of the following environments.
• Restricted Environments
• Commercial buildings
• Buildings with indoor pools
• Furnaces installed in laundry rooms
• Furnaces installed in hobby or craft rooms
• Furnaces installed near chemical storage areas
• Chemical Exposure
The furnace will require OUTDOOR AIR for combustion when the furnace is located in an area where the furnace is being exposed to the following substances and / or chemicals.
• Permanent wave solutions
• Chlorinated waxes and cleaners
• Chlorine based swimming pool chemicals
• Water softening chemicals
• De-icing salts or chemicals
• Carbon tetrachloride
• Halogen type refrigerants
• Cleaning solvents (such as perchloroethylene)
• Printing inks, paint removers, varnishes, etc.
• Hydrochloric acid
• Cements and glues
• Antistatic fabric softeners for clothes dryers
• Masonry acid washing materials
When outdoor air is used for combustion, the combustion air intake pipe
termination must be located external to the building and in an area
where there will be no exposure to the substances listed above.
Unitary Products Group
035-20417-001 Rev. C (0904)
Installation in freezing temperatures:
The furnace area must not be used as a broom closet or for any
other storage purposes, as a fire hazard may be created. Never
store items such as the following on, near or in contact with the furnace.
1. Spray or aerosol cans, rags, brooms, dust mops, vacuum
cleaners or other cleaning tools.
2. Soap powders, bleaches, waxes or other cleaning compounds; plastic items or containers; gasoline, kerosene, cigarette lighter fluid, dry cleaning fluids or other volatile fluid.
3. Paint thinners and other painting compounds.
4. Paper bags, boxes or other paper products
Never operate the furnace with the blower door removed. To
do so could result in serious personal injury and/or equipment
damage.
INSPECTION
As soon as a unit is received, it should be inspected for possible damage during transit. If damage is evident, the extent of the damage
should be noted on the carrier’s freight bill. A separate request for
inspection by the carrier’s agent should be made in writing. Also, before
installation the unit should be checked for screws or bolts, which may
have loosened in transit. There are no shipping or spacer brackets
which need to be removed.
FURNACE LOCATION AND CLEARANCES
The furnace shall be located using the following guidelines:
1.
2.
3.
4.
5.
6.
Where a minimum amount of air intake/vent piping and elbows will
be required.
As centralized with the air distribution as possible.
Where adequate combustion air will be available (particularly
when the appliance is not using outdoor combustion air).
Where it will not interfere with proper air circulation in the confined
space.
Where the outdoor combustion air/vent terminal will not be blocked
or restricted. Refer to “COMBUSTION AIR / VENT CLEARANCES” located in SECTION VII of these instructions. These minimum clearances must be maintained in the installation.
Where the unit will be installed in a level position with no more
than 1/4” (6.4 mm) slope side-to-side and front-to-back to provide
proper condensate drainage.
1.
Furnace shall be installed in an area where ventilation facilities
provide for safe limits of ambient temperature under normal operating conditions. Ambient temperatures must not fall below 32°F
(0°C) unless the condensate system is protected from freezing.
2.
Do not allow return air temperature to be below 55º F (13° C) for
extended periods. To do so may cause condensation to occur in
the main heat exchanger, leading tp premature heat exchanger
failure.
Improper installation in an ambient below 32ºF (0.0° C) could create
a hazard, resulting in damage, injury or death.
3.
If this furnace is installed in any area where the ambient temperature may drop below 32° F (0° C), a UL listed self-regulated heat
tape must be installed on any condensate drain lines. It is required
that self regulating heat tape rated at 3 watts per foot be used.
This must be installed around the condensate drain lines in the
unconditioned space. Always install the heat tape per the manufacturer's instructions. Cover the self-regulating heat tape with
fiberglass, Armaflex or other heat resistant insulating material.
4. If this unit is installed in an unconditioned space and an extended
power failure occurs, there will be potential damage to the condensate trap, drain lines and internal unit components. Following a
power failure situation, do not operate the unit until inspection and
repairs are performed.
Clearances for access:
Ample clearances should be provided to permit easy access to the unit.
The following minimum clearances are recommended:
1.
Twenty-four (24) inches (61 cm) between the front of the furnace
and an adjacent wall or another appliance, when access is
required for servicing and cleaning.
2.
Eighteen (18) inches (46 cm) at the side where access is required
for passage to the front when servicing or for inspection or
replacement of flue/vent connections.
In all cases, accessibility clearances shall take precedence over clearances for combustible materials where accessibility clearances are
greater.
Installation in a residential garage:
1.
A gas-fired furnace for installation in a residential garage must be
installed so the burner(s) and the ignition source are located not
less than 18 inches (46 cm) above the floor, and the furnace must
be located or protected to avoid physical damage by vehicles.
TABLE 1: Unit Clearances to Combustibles
APPLICATION
UPFLOW
TOP
FRONT
REAR
LEFT SIDE
RIGHT SIDE
FLUE
In. (mm)
In. (mm)
In. (mm)
In. (mm)
In. (mm)
In. (mm)
FLOOR/
BOTTOM
CLOSET
ALCOVE
ATTIC
1 (25.4)
3
0 (0)
0 (0)
0 (0)
0 (0)
COMBUSTIBLE
YES
YES
SECTION II: DUCTWORK
DUCTWORK GENERAL INFORMATION
4.
Complete a path for heated or cooled air to circulate through the
air conditioning and heating equipment and to and from the conditioned space.
The duct system’s design and installation must:
1.
Handle an air volume appropriate for the served space and within
the operating parameters of the furnace specifications.
2.
Be installed in accordance with standards of NFPA (National Fire
Protection Association) as outlined in NFPA pamphlets 90A and
90B (latest editions) or applicable national, provincial, or state, and
local fire and safety codes.
3.
Create a closed duct system. For residential and Non-HUD Modular Home installations, when a furnace is installed so that the supply ducts carry air circulated by the furnace to areas outside the
space containing the furnace, the return air shall also be handled
by a duct(s) sealed to the furnace casing and terminating outside
the space containing the furnace.
Unitary Products Group
The cooling coil must be installed in the supply air duct, downstream of the furnace. Cooled air may not be passed over the heat
exchanger.
When the furnace is used in conjunction with a cooling coil, the coil
must be installed parallel with, or in the supply air side of the furnace to
avoid condensation in the primary heat exchanger. When a parallel flow
arrangement is used, dampers or other means used to control airflow
must be adequate to prevent chilled air from entering the furnace. If
manually operated, the damper must be equipped with means to prevent the furnace or the air conditioner from operating unless the damper
is in full heat or cool position.
3
035-20417-001 Rev. C (0904)
The duct system must be properly sized to obtain the correct airflow
for the furnace size that is being installed.
Refer to Table 7 and the furnace rating plate for the correct rise
range and static pressures
If the ducts are undersized, the result will be high duct static pressures and/or high temperature rises which can result in a heat
exchanger OVERHEATING CONDITION. This condition can result
in premature heat exchanger failure, which can result in personal
injury, property damage, or death.
DUCTWORK INSTALLATION AND SUPPLY PLENUM
CONNECTION
Attach the supply plenum to the furnace outlet duct connection flanges. This is typically through the use of S cleat
material when a metal plenum is used. The use of an
approved flexible duct connector is recommended on all
installations. This connection should be sealed to prevent
air leakage. The sheet metal should be crosshatched to
eliminate any popping of the sheet metal when the indoor
fan is energized.
When replacing an existing furnace, if the existing plenum is not the
same size as the new furnace then the existing plenum must be
removed and a new plenum installed that is the proper size for the new
furnace. The minimum plenum height is 12” (30 cm). If the plenum is
shorter than 12” (30 cm) the turbulent air flow may cause the limit controls not to operate as designed, or the limit controls may not operate at
all.
The duct system is a very important part of the installation. If the duct
system is improperly sized the furnace will not operate properly.
The ducts attached to the furnace plenum, should be of sufficient size
so that the furnace operates at the specified external static pressure
and within the air temperature rise specified on the nameplate.
Table 2 is a guide for determining whether the rectangular duct system
that the furnace is being connected to be of sufficient size for proper furnace operation.
Use the Example below to help you in calculating the duct area to determine whether the ducts have sufficient area so that the furnace operates at the specified external static pressure and within the air
temperature rise specified on the nameplate.
Example: The furnace input is 80,000 BTUH, The recommended duct
area is 248 sq.in, there are two 8 x 12 rectangular ducts attached to the
plenum and there are two 7 inch round ducts attached to the furnace.
1.
Take 8 x 14, which equals 112 sq.in. X 2, which equals 224 square
inch then go to round duct size located in Table 3.
2.
The square inch area for 7 inch round pipe is 38.4, multiply by 2 for
two round ducts which equals 76.8 square inch,
3.
Then take the 224 square inch from the rectangular duct and add it
to the 76.8 sq.in. of round duct. The total square inch of duct
attached to the furnace plenum is 300.8 square inch. This exceeds
the recommended 280 square inch of duct.
In this example, the duct system attached to the plenum has a sufficient
area so that the furnace operates at the specified external static pressure and within the air temperature rise specified on the nameplate.
TABLE 2: Minimum Duct Sizing For Proper Airflow
Input
Airflow
Return1
Rectangular2
Round2
Supply3
Rectangular2
Round2
in. (cm) dia.
BTU/H (kW)
CFM (m³)
In² (cm²)
in. x in. (cm x cm)
in. (cm) dia.
In² (cm²)
in. x in. (cm x cm)
40,000(17.58)
1,200 (33.98)
280 (711)
14 x 20 (35.6 x 50.8)
18 (45.7)
216 (549)
12 x 18 (30.5 x 45.7)
16 (40.6)
60,000 (17.58)
1,200 (33.98)
280 (711)
14 x 20 (35.6 x 50.8)
18 (45.7)
216 (549)
12 x 18 (30.5 x 45.7)
16 (40.6)
80,000 (23.44)
1,200 (33.98)
280 (711)
14 x 20 (35.6 x 50.8)
18 (45.7)
216 (549)
12 x 18 (30.5 x 45.7)
16 (40.6)
80,000 (23.44)
1,600 (45.31)
360 (914)
18 x 20 (45.7 x 50.8)
22 (55.8)
280 (711)
14 x 20 (35.6 x 50.8)
18 (45.7)
100,000 (29.31)
1,600 (45.31)
360 (914)
18 x 20 (45.7 x 50.8)
22 (55.8)
280 (711)
14 x 20 (35.6 x 50.8)
18 (45.7)
100,000 (29.31)
2,000 (56.63)
440 (1,118)
20 x 22 (50.8 x 55.8)
24 (60.9)
390 (991)
16 x 22 (40.6 x 55.8)
22 (55.8)
120,000 (35.17)
2,000 (56.63)
440 (1,118)
20 x 22 (50.8 x 55.8)
24 (60.9)
390 (991)
16 x 22 (40.6 x 55.8)
22 (55.8)
NOTE: This chart does not replace proper duct sizing calculations or take into account static pressure drop for run length and fittings. Watch out for the temperature rise and static pressures.
1. Maximum return air velocity in rigid duct @ 700 feet per minute (19.82 m3 / minute).
2. Example return main trunk duct minimum dimensions.
3. Maximum supply air velocity in rigid duct @ 900 feet per minute (25.49 m3 / minute).
TABLE 3: Round Duct Size
1.
2.
4
Round Duct Size
Calculated Area For Each Round Duct Size
inches (cm)
Sq.in (cm2)
5 (13)
19.6 (126)
6 (15)
28.2 (182)
7 (18)
38.4 (248)
8 (20)
50.2 (324)
9 (23)
63.6 (410)
10 (25)
78.5 (506)
11 (28)
95 (613)
12 (30)
113.1 (730)
13 (33)
132.7 (856)
14 (36)
153.9 (993)
The Air Temperature Rise is determined by subtracting the Return
Air Temperature Reading from the Supply Air Temperature Reading.
The External Static Pressure is determined by adding the Supply
Duct Static Pressure reading to the Return Duct Static Pressure
reading and adding the pressure drop across any applied coil.
TABLES 2 AND 3 are to be used as a guide only to help the installer
determine if the duct sizes are large enough to obtain the proper air flow
(CFM) through the furnace. TABLES 2 and 3 ARE NOT to be used to
design ductwork for the building where the furnace is being installed.
There are several variables associated with proper duct sizing that are
not included in the tables. To properly design the ductwork for the building, Refer to the ASHRAE Fundamentals Handbook, Chapter on
“DUCT DESIGN” or a company that specializes in Residential and Modular Home duct designs.
IMPORTANT: The minimum plenum height is 12” (30 cm). The furnace
will not operate properly on a shorter plenum height. The minimum recommended rectangular duct height is 4” (10 cm) attached to the plenum.
IMPORTANT: The air temperature rise should be taken only after the
furnace has been operating for at least 15 minutes. Temperatures and
external static pressures should be taken 6” (15 cm) past the first bend
from the furnace in the supply duct and the return duct. If an external filter box or an electronic air cleaner is installed, take the return air readings before the filter box or air cleaner.
Unitary Products Group
035-20417-001 Rev. C (0904)
If a matching cooling coil is used, it may be placed directly on the furnace outlet and sealed to prevent leakage. Follow the coil instructions
for installing the supply plenum. On all installations without a coil, a
removable access panel is recommended in the outlet duct such that
smoke or reflected light would be observable inside the casing to indicate the presence of leaks in the heat exchanger. This access cover
shall be attached in such a manner as to prevent leaks.
The supply air temperature MUST NEVER exceed the Maximum
Supply Air Temperature, specified on the nameplate.
Operating the furnace above the maximum supply air temperature
will cause the heat exchanger to overheat, causing premature heat
exchanger failure. Improper duct sizing, dirty air filters, incorrect
manifold pressure, incorrect gas orifice and/or a faulty limit switch
can cause the furnace to operate above the maximum supply air
temperature. Refer to sections II and III for additional information on
correcting the problem.
26-1/2
26-1/2
24-5/8
A
25-3/8
1-1/2” GAS
PIPE ENTRY
1-1/2” GAS
PIPE ENTRY
7/8” JUNCTION
BOX HOLE
T-STAT WIRING
7/8” K.O.
30-7/8
CONDENSAATE
DRAIN 7/8” K.O.
21-1/2
28-3/8
21-1/2
OPTIONAL RETURN AIR
CUT-OUT (either side)
FOR USE WITH
EXTERNAL FILTER
FRAME
7/8
7/8” JUNCTION
BOX HOLE
40
T-STAT WIRING
7/8” K.O.
13-7/8
11
11
8
7
23-3/4
30-1/8
FRONT
7/8
CONDENSAATE
DRAIN 7/8” K.O.
RIGHT SIDE
LEFT SIDE
1-3/8
26-3/4
24-3/8
1-1/4
20
5/8
5/8
D
B
C
1-3/4
BOTTOM IMAGE
RETURN END
26-1/2
TOP IMAGE
SUPPLY END
Cabinet Dimension
Air Intake
CFM
Cabinet
BTUH (kW)
Input/Output
Size A (in.) A (cm) B (in.) B (cm) C (in.) C (cm) D (in.) D (cm)
m3/min)
40/38 (11.7/10.8) 1200 (33.98)
A
14-1/2 36.8 13-1/4 33.7 12-1/8 30.8 6-1/4 15.9
60/56 (17.8/16.1) 1200 (33.98)
B
17-1/2 44.4 16-1/4 41.3 15-1/8 38.4 8-1/2 21.6
80/75 (12.4/21.96) 1200 (33.98)
B
17-1/2 44.4 16-1/4 41.3 15-1/8 38.4 8-1/2 21.6
80/75 (23.42/21.96) 1600 (45.31)
C
21
53.3 19-3/4 50.2 18-1/2 47.0 8-7/8 22.5
100/93 (29.28/27.82) 1600 (45.31)
C
21
53.3 19-3/4 50.2 18-1/2 47.0 8-7/8 22.5
100/93 (29.28/27.82) 2000 (56.63)
C
21
53.3 19-3/4 50.2 18-1/2 47.0 8-7/8 22.5
120/112 (35.14/32.80) 2000 (56.63)
D
24-1/2 62.2 23-1/4 59.4 21-7/8 55.6 10-5/8 27.0
FIGURE 1: Dimensions
RESIDENTIAL AND NON HUD MODULAR HOME
RETURN PLENUM CONNECTION
Attic installations must meet all minimum clearances to combustibles
and have floor support with required service accessibility.
Return air may enter the furnace through the side(s) or bottom depending on the type of application. Return air may not be connected into the
rear panel of the unit. In order to achieve the airflow indicated, it is recommended those applications over 1800 CFM (57 m³/min) use return
air from two sides, one side and the bottom or bottom only. For single
return application, see data and notes on blower performance data
tables in this manual.
Removable Rectangular
Base Panel.
BOTTOM RETURN AND ATTIC INSTALLATIONS
Toe Plate
Bottom return applications normally pull return air through a base platform or return air plenum. Be sure the return platform structure or return
air plenum is suitable to support the weight of the furnace.
The furnace base is equipped with a rectangular blockoff panel that can
be removed by performing the following steps:
1.
2.
3.
4.
5.
Lay the furnace on its back.
Remove the toe plate. See Figure 2.
Slide the blockoff panel out and then replace the toe plate.
Bend the 3/4” flanges that will be used to attach the return air plenum using the scribe marks in the furnace base. Refer to Figure 1
“Bottom Image Return End”.
Be sure to seal the furnace to plenum connections to prevent air
leakage. Refer to Figure 1 for unit and plenum dimensions.
Unitary Products Group
FIGURE 2: Furnace Base Rectangular Blockoff Panel
IMPORTANT: If an external mounted filter rack is being used see the
instructions provided with that accessory for proper hole cut size.
SECTION III: FILTERS
FILTER INSTALLATION
All applications require the use of a filter. A high velocity filter and a side
return filter rack are provided for field installation. Replacement filter
size is shown in Table 4.
Filters must be installed external to the furnace cabinet. DO NOT
attempt to install filters inside the furnace.
5
035-20417-001 Rev. C (0904)
TABLE 4: Filter Sizes
Cabinet
Input / Output CFM
BTU/H (kW) (m3/min) Size
Side Return
Filter in. (cm)
Bottom Return
Filter in. (cm)
14 x 25
(36 x 64)
IMPORTANT: Plan your gas supply before determining the correct gas
pipe entry. Use 90-degree service elbow(s), or short nipples and conventional 90-degree elbow(s) to enter through the cabinet access holes.
CHECKING THE GAS PRESSURES
40/38/1200
(11.7/10.8)
1200
(34)
A
16 x 25
(41 x 64)
60/56/1200
(17.57/16.10)
1200
(34)
B
16 x 25
(41 x 64)
16 x 25
(41 x 64)
2.
3.
80/75/1200
(23.42/21.96)
1200
(34)
B
16 x 25
(41 x 64)
16 x 25
(41 x 64)
4.
80/75/1600
(23.42/21.96)
1600
(45)
C
16 x 25
(41 x 64)
20 x 25
(51 x 64)
100/93/1600
(29.28/27.82)
1600
(45)
C
16 x 25
(41 x 64)
20 x 25
(51 x 64)
100/93/2000
(29.28/32.80)
2000
(57)
C
16 x 25
(41 x 64)
20 x 25
(51 x 64)
120/112/2000
(35.14/32.80)
2000
(57)
D
(2) 16 x 25
(2) (41 x 64)
22 x 25
(56 x 64)
1.
5.
6.
The pressure ports on the gas valve are marked OUT P and IN
P.
The manifold pressure must be taken at the port marked OUT P.
The inlet gas supply pressure must be taken at the port marked
IN P.
Using a 3/32” (0.2 cm) Allen wrench, loosen the set screw by
turning it 1 turn counter clockwise. DO NOT REMOVE THE
SET SCREW FROM THE PRESSURE PORT.
Push one end the 3/8” (0.9 cm) ID flexible tubing over the pressure port so that the body of the port is inside the tubing.
Use a reducer connector to connect the 3/8” (0.9 cm) ID flexible
tube to a 1/4” (0.6 cm) ID flexible tube that is connected to a "U”
tube manometer or digital pressure measuring equipment.
TABLE 5: Inlet Gas Pressure Range
INLET GAS PRESSURE RANGE
SIDE RETURN - FILTER INSTALLATION
Locate and mark the side return opening. Refer to Figure 1 for dimensions of the cutout.
Install the side filter rack following the instructions provided with that
accessory. If a filter(s) is provided at another location in the return air
system, the ductwork may be directly attached to the furnace side
panel.If not provided with the furnace, an accessory filter rack is available for mounting the filter external to the cabinet.
IMPORTANT: Some accessories such as electronic air cleaners and
pleated media may require a larger side opening. Follow the instructions supplied with that accessory for side opening requirements. Do
not cut the opening larger than the dimensions shown in Figure 1.
SECTION IV: GAS PIPING
IMPORTANT: The inlet gas pressure operating range table specifies
what the minimum and maximum gas line pressures must be for the
furnace to operate safely. The gas line pressure MUST BE
• 7” W.C. (1.74 kPA) for Natural Gas
• 11” W.C. (2.74 kPA) for Propane (LP) Gas
in order to obtain the BTU input specified on the rating plate and/or
the nominal manifold pressure specified in these instructions and on
the rating plate.
GAS PIPING INSTALLATION
Some utility companies or local codes require pipe sizes larger than the
minimum sizes listed in these instructions and in the codes. The furnace
rating plate and the instructions in this section specify the type of gas
approved for this furnace - only use those approved gases. The installation of a drip leg and ground union is required. Refer to Figure 4.
GAS SAFETY
An overpressure protection device, such as a pressure regulator,
must be installed in the gas piping system upstream of the furnace
and must act to limit the downstream pressure to the gas valve so it
does not exceed 0.5 PSI (14" w.c. (3.48 kPa). Pressures exceeding
0.5 PSI (14” w.c. (3.48 kPa) at the gas valve will cause damage to
the gas valve, resulting in a fire or explosion or cause damage to
the furnace or some of its components that will result in property
damage and loss of life.
HIGH STAGE REGULATOR
ADJUSTMENT
OUTLET
WRENCH
BOSS
INLET
PRESSURE
PORT
ON OFF
SWITCH
EXTERNAL MANUAL
SHUTOFF VALVE
TO GAS
SUPPLY
DRIP
LEG
VENT
PORT
INLET
Propane (LP)
8.0” W.C. (1.99 kPa)
13.0” (3.24 kPa) W.C.
Properly sized wrought iron, approved flexible or steel pipe must be
used when making gas connections to the unit. If local codes allow the
use of a flexible gas appliance connection, always use a new listed connector. Do not use a connector that has previously serviced another gas
appliance.
All installations must have a filter installed.
OUTLET
PRESSURE
PORT
Natural Gas
4.5” W.C. (1.12 kPa)
10.5” W.C. (2.61 kPa)
Minimum
Maximum
LOW STAGE REGULATOR
ADJUSTMENT
TO GAS
SUPPLY
GROUNDED JOINT UNION
MAY BE INSTALLED
INSIDE OR OUTSIDE UNIT.
FIGURE 4: Gas Piping
IMPORTANT: An accessible manual shutoff valve must be installed
upstream of the furnace gas controls and within 6 feet (1.8 m) of the furnace.
The furnace must be isolated from the gas supply piping system by
closing its individual external manual shutoff valve during any pressure
testing of the gas supply piping system at pressures equal to or less
than 1/2 psig (3.5 kPa).
FIGURE 3: Gas Valve
6
Unitary Products Group
035-20417-001 Rev. C (0904)
TABLE 6: High Altitude Conversion
The gas valve body is a very thin casting that cannot take any
external pressure. Never apply a pipe wrench to the body of the gas
valve when installing piping. A wrench must be placed on the octagon hub located on the gas inlet side of the valve. Placing a wrench
to the body of the gas valve will damage the valve causing improper
operation and/or the valve to leak.
Gas piping may be connected from either side of the furnace using any
of the gas pipe entry knockouts on both sides of the furnace. Refer to
Figure 1 dimensions.
The inlet to the gas valve lines up directly with the opening in the left
side of the furnace casing. To line up with the opening in the right side
of the casing, two street ells should be used.
Type
Of Gas
Orifice at
Sea Level
2,000 ft.
(610 m)
3,000 ft.
(914 m)
4,000 ft.
(1219 m)
Natural
Propane
#45
#55
#46
#55
#47
#55
#47
#55
Type
Of Gas
5,000 ft.
(1524 m)
6,000 ft.
(1829 m)
7,000 ft.
(2134 m)
8,000 ft.
(2438 m)
Natural
Propane
#47
#56
#48
#56
#48
#56
#49
#56
Type
Of Gas
9,000 ft.
(2743 m)
10,000 ft.
(3048 m)
Natural
Propane
#49
#56
#50
#57
GAS ORIFICE CONVERSION FOR PROPANE (LP)
This furnace is constructed at the factory for natural gas-fired operation,
but may be converted to operate on propane (LP) gas by using a factory-supplied LP conversion kit. Follow the instructions supplied with
the LP kit. Refer to Table 6 or the instructions in the propane (LP) conversion kit for the proper gas orifice size.
PROPANE AND HIGH ALTITUDE CONVERSION KITS
It is very important to choose the correct kit and/or gas orifices for
the altitude and the type of gas for which the furnace is being
installed.
Only use natural gas in furnaces designed for natural gas. Only use
propane (LP) gas for furnaces that have been properly converted to
use propane (LP) gas. Do not use this furnace with butane gas.
Incorrect gas orifices or a furnace that has been improperly converted will create an extremely dangerous condition resulting in premature heat exchanger failure, excessive sooting, high levels of
carbon monoxide, personal injury, property damage, a fire hazard
and/or death.
High altitude and propane (LP) conversions are required in order
for the appliance to satisfactory meet the application.
An authorized distributor or dealer must make all gas conversions.
In Canada, a certified conversion station or other qualified agency,
using factory specified and/or approved parts, must perform the
conversion.
The installer must take every precaution to insure that the furnace
has been converted to the proper gas orifice size when the furnace
is installed. Do not attempt to drill out any orifices to obtain the
proper orifice size. Drilling out a gas orifice will cause misalignment
of the burner flames, causing premature heat exchanger burnout,
high levels of carbon monoxide, excessive sooting, a fire hazard,
personal injury, property damage and/or death.
HIGH ALTITUDE GAS ORIFICE CONVERSION
This furnace is constructed at the factory for natural gas-fired operation
at 0 – 2,000 ft. (0 m – 610 m) above sea level.
The gas orifices on this furnace must be changed in order to maintain
proper and safe operation, when the furnace is installed in a location
where the altitude is greater than 2,000 ft. (610 m) above sea level on
natural gas or the altitude is greater than 4,000 ft. (1219 m) above sea
level on propane (LP) gas. Refer to Table 6 or the instructions in the
high altitude conversion kit for the proper gas orifice size.
The unit may also be converted for altitudes up to 10,000 ft. (3048 m)
on natural and propane (LP) gas with additional derate as shown in
Table 6 or refer to ANSI Z223.1 NFPA 54 National Fuel Gas Code or in
Canada CAN/CGA-B149.1-00 Natural Gas and Propane Installation
Code.
HIGH ALTITUDE PRESSURE SWITCH CONVERSION
For installation in locations where the altitude is less than 4,500 feet
(1372 m), it is not required that the pressure switch be changed, provided the maximum vent/intake pipe lengths are adjusted as shown in
the notes to Table 9. For altitudes above 4,500 feet (137 m), refer to
Instructions in the Accessory High Altitude Kit.
SECTION V: ELECTRICAL POWER
TABLE 7: Electrical and Performance Data
Input
High/Low
Output
High/Low
Nominal Airflow AFUE Air Temp. Rise
Max. Outlet
Air Temp.
Blower
Blower Size
Total Unit
Max.
Min. Wire Size
Over-current (awg) @ 75 ft.
Protect
One Way
MBH
kW
MBH
kW
CFM
m3/min
%
°F
°C
°F
°C
HP Amps
In.
mm
Amps
40/26
12/8
38/24
11/7
1200
34
92.0
35-65
19-36
165
74
1/2
7
10x8
254x203
9
20
14
60/39
18/11
56/36
16/11
1200
34
92.0
40-70
22-39
170
77
1/2
7
11x8
279x203
9
20
14
80/52
23/15
75/49
22/14
1200
34
92.0
45-75
25-42
175
79
1/2
7
11x8
279x203
9
20
14
80/52
23/15
75/49
22/14
1600
45.3
92.0
45-75
25-42
175
79
3/4
10.2
11x10 279x254
12
20
14
100/65 29/19
93/61
27/18
1600
45.3
92.0
45-75
25-42
175
79
3/4
10.2
11x10 279x254
12
20
14
100/65 29/19
93/61
27/18
2000
56.6
92.0
45-75
25-42
175
79
1
12.7
11x11 279x279
14
20
12
120/78 35/23 112/74 33/22
2000
56.6
92.0
40-70
22-39
170
77
1
12.7
11x11 279x279
14
20
12
Annual Fuel Utilization Efficiency (AFUE) numbers are determined in accordance with DOE Test procedures.
Wire size and over current protection must comply with the National Electrical Code (NFPA-70-latest edition) and all local codes.
The furnace shall be installed so that the electrical components are protected from water.
Unitary Products Group
7
035-20417-001 Rev. C (0904)
ELECTRICAL POWER CONNECTIONS
LOW VOLTAGE CONTROL WIRING CONNECTIONS
Field wiring to the unit must be grounded. Electric wires that are field
installed shall conform to the temperature limitation for 63°F (35°C) rise
wire when installed in accordance with instructions. Refer to Table 7 in
these instructions for specific furnace electrical data.
Install the field-supplied thermostat by following the instructions that
come with the thermostat. With the thermostat set in the OFF position
and the main electrical source disconnected, connect the thermostat
wiring from the wiring connections on the thermostat to the terminal
strip on the furnace control board, as shown in Figures 7, 8, or 9. Electronic thermostats may require the common wire to be connected to the
"C" terminal as shown in Figures 7, 8 or 9. Apply strain relief to thermostat wires passing through cabinet. If air conditioning equipment is
installed, use thermostat wiring to connect the Y and C terminals on the
furnace control board to the condensing unit (unit outside) as shown in
Figures 7, 8 or 9.
Use copper conductors only.
SUPPLY VOLTAGE CONNECTIONS
1.
2.
3.
Provide a power supply separate from all other circuits. Install
overcurrent protection and disconnect switch per local/national
electrical codes. The switch should be close to the unit for convenience in servicing. With the disconnect or fused switch in the OFF
position, check all wiring against the unit wiring label. Refer to the
wiring diagram in this instruction.
Remove the screws retaining the wiring box cover. Route the
power wiring through the opening in the unit into the junction box
with a conduit connector or other proper connection. In the junction box there will be three wires, a Black Wire, a White Wire and a
Green Wire. Connect the power supply as shown on the unit-wiring label on the inside of the blower compartment door or the wiring schematic in this section. The black furnace lead must be
connected to the L1 (hot) wire from the power supply. The white
furnace lead must be connected to neutral. Connect the green furnace lead (equipment ground) to the power supply ground. An
alternate wiring method is to use a field provided 2” (51 mm) x 4”
(102 mm) box and cover on the outside of the furnace. Route the
furnace leads into the box using a protective bushing where the
wires pass through the furnace panel. After making the wiring connections replace the wiring box cover and screws. A power shutoff
switch may be installed in this box. Refer to Figure 5.
The furnace's control system requires correct polarity of the power
supply and a proper ground connection. Refer to Figure 6.
IMPORTANT: The power connection leads and wiring box may be relocated to the left side of the furnace. Remove the screws and cut wire tie
holding excess wiring. Reposition on the left side of the furnace and fasten using holes provided.
L1
N HOT
IMPORTANT: Set the heat anticipator in the room thermostat to 0.10
amps. Setting it lower will cause short cycles. Setting it higher will cause
the room temperature to exceed the set points.
BLK
BLK (HOT)
WHT
WHT (NEUTRAL)
GRN
GRN
FIGURE 6: Line Wiring Connections
ROOM
THERMOSTAT
R
W
G
Y
C
ROOM
THERMOSTAT
R
W
G
Y1
Y2
C
WHT
BLK
CONDENSING
UNIT
R
TO AIR CONDITIONER
W1/W
CONTROLS
G
Y/Y2
C
COMMON T’STAT CONNECTION
FURNACE
CONTROL
CONDENSING
UNIT
R
TO AIR CONDITIONER
W1/W
CONTROLS
G
Y1
Y/Y2
C
COMMON T’STAT CONNECTION
FIGURE 8: Single Stage Heating and Two-Stage Cooling Thermostat
Connections
R
W1
W2
G
Y1
Y2
C
GRN
FURNACE
CONTROL
FIGURE 7: Single Stage Heat Thermostat Connections
ROOM
THERMOSTAT
GND
NOMINAL
120 VOLT
FURNACE
CONTROL
R
W1/W
W2
G
Y1
Y/Y2
C
CONDENSING
UNIT
TO AIR CONDITIONER
CONTROLS
COMMON T’STAT CONNECTION
FIGURE 9: Two Stage Heating and Two-Stage Cooling Thermostat
Connections
BLK/BLK
WHT/WHT
GRN/GRN
IMPORTANT: Some electronic thermostats do not have adjustable heat
anticipators. They may have other type cycle rate adjustments. Follow
the thermostat manufacturer's instructions.
CLASS 2 SYSTEM
CONTROL WIRING
TO THERMOSTAT
The 24-volt, 40 VA transformer is sized for the furnace components
only, and should not be connected to power auxiliary devices such as
humidifiers, air cleaners, etc. The transformer may provide power for an
air conditioning unit contactor.
BLOWER
COMPARTMENT
DOOR SWITCH
TRANSFORMER
FIGURE 5: Electrical Wiring
8
IGNITION
MODULE
Using a Single-Stage Heat Thermostat with the Furnace - This twostage furnace may be used with a single-stage thermostat. Connect the
thermostat as shown in Figure 7. Place the “W2 Delay” jumper in the 10
minute, 15 minute or 20 minute position. If the jumper is left on the
“OFF” pins, the furnace will operate only in low fire.
Unitary Products Group
035-20417-001 Rev. C (0904)
ACCESSORY CONNECTIONS
The furnace control will allow power-switching control of various accessories. Refer to Figure 8, for connection details.
When combustion air pipe is installed above a suspended ceiling or
when it passes through a warm and humid space, the pipe must be
insulated with 1/2” Armaflex or other heat resistant type insulation if
two feet or more of pipe is exposed.
Vent piping must be insulated if it will be subjected to freezing temperatures such as routing through unheated areas or through an
unused chimney.
HUM. HOT
115 VOLT
HUMIDIFER
BLK
WHT
EAC SWITCHED
HUM CIRCUITS
EAC HOT
COMBUSTION AIR/VENT PIPE SIZING
115 VOLT
ELECTRONIC
AIR CLEANER
BLK
WHT
NEUTRALS
Select the correct size from Table 9. The size will be determined by a
combination of furnace model, total length of run, and the number of
elbows required. The following rules must also be observed.
1.
Long radius (sweep) elbows are required for all units.
2.
Elbows are assumed to be 90 degrees. Two 45-degree elbows
count as one 90-degree elbow.
Two 1/4” (6.4 mm) spade terminals (EAC and NEUTRAL) for electronic
air cleaner connections are located on the control board. The terminals
provide 115 VAC (1.0 amp maximum) during circulating blower operation.
3.
Elbow count refers to combustion air piping and vent piping separately. For example, if the table allows for 5 elbows, this will allow a
maximum of 5 elbows in the combustion air piping and a maximum
of 5 elbows in the vent piping.
HUMIDIFIER CONNECTION
4.
Three vent terminal elbows (two for vent pipe and one for air
intake pipe) are already accounted for as vent termination.
Two 1/4” (6.4 mm) spade terminals (HUM and NEUTRAL) for humidifier
connections are located on the control board. The terminals provide 115
VAC (1.0 amp maximum) during heating system operation.
5.
Combustion air and vent piping must be of the same diameter.
6.
All combustion air/vent pipe and fittings must conform to American
National Standards Institute (ANSI) standards and American Society for Testing and Materials (ASTM) standards D1785 (Schedule
40 PVC), D2665 (PVC-DWV), F891 (PVC-DWV Cellular Core).
D2241 (SDR-21 and SDR-26 PVC), D2261 (ABS-DWV), or F628
(Schedule 40 ABS. Pipe cement and primer must conform to
ASTM Standards D2564 (PVC) or D2235 (ABS).
SECTION VI: COMBUSTION AIR AND
VENT SYSTEM
7.
The use of flexible connectors or no hub connectors in the vent
system is not allowed. This type connection is allowed in the combustion air pipe near the furnace for air conditioning coil accessibility.
This Category IV, dual certified direct vent furnace is designed for residential application. It may be installed without modification to the condensate system in a basement, garage, equipment room, alcove, attic
or any other indoor location where all required clearance to combustibles and other restrictions are met. The combustion air and the venting
system must be installed in accordance with Section 5.3, Air for Combustion and Ventilation, of the National Fuel Gas Code Z223.1/NFPA 54
(latest edition), or Sections 7.2, 7.3 or 7.4 of CSA B149.1, National Gas
and Propane Codes (latest edition) or applicable provisions of the local
building code and these instructions.
8.
Sidewall horizontal vent terminals and roof mounted vertical terminals may be field fabricated. Standard PVC/SRD fittings may be
used. Terminal configuration must comply as detailed in this section.
FIGURE 10: Accessory Connections
ELECTRONIC AIR CLEANER CONNECTION
TWINNING
These furnaces are not to be twinned. If more than one furnace is
needed in an application, each furnace must have its own complete
duct system and its own wall thermostat.
COMBUSTION AIR AND VENT SAFETY
IMPORTANT: The “VENT SYSTEM” must be installed as specified in
these instructions for Residential and Non HUD Modular Homes. The
sealed combustion air / vent system is the only configuration that can
be installed in a Non HUD Modular Home.
IMPORTANT: Accessory concentric vent / intake termination kits
1CT0302 and 1CT0303 are available and approved for use with these
furnaces.
IMPORTANT: Intake and vent pipe connections are sized as shown
above. However, most models require larger vents and some installations will require larger intake piping. Use Table 9 for the sizes of the
pipe that can be used with each model.
TABLE 8: Combustion Air Intake and Vent Connection Size at Furnace
(All Models)
FURNACE VENT CONNECTION SIZES
Furnace Input
This furnace may not be common vented with any other appliance,
since it requires separate, properly sized air intake and vent lines.
The furnace shall not be connected to any type of B, BW or L vent
or vent connector, and not connected to any portion of a factorybuilt or masonry chimney
The furnace shall not be connected to a chimney flue serving a separate appliance designed to burn solid fuel.
Unitary Products Group
Intake Pipe Size
Vent Pipe Size
40 - 100 MBH
(17.5-29.3 kW)
2” (51 mm)
1-1/2” (38 mm)
120 MBH
(35.2 kW)
3" (76 mm)
1-1/2" (38 mm)
9
035-20417-001 Rev. C (0904)
TABLE 9: Combustion Air Supply and Vent Piping
Models Input
BTUH (kW)
40,000 (11.7)
40,000 (11.7)
60,000 (17.6)
60,000 (17.6)
60,000 (17.6)
80,000 (23.4)
80,000 (23.4)
80,000 (23.4)
100,000 (29.3)
100,000 (29.3)
120,000 (35.1)
Pipe Size
Inches (cm)
1-1/2 (3.8)
2 (5.1)
1-1/2 (3.8)
2 (5.1)
3 (7.6)
1-1/2 (3.8)
2 (5.1)
3 (7.6)
2 (5.1)
3 (7.6)
3 (7.6)
MAXIMUM ELBOWS AND VENT LENGTHS
Maximum Number of Elbows*
1
2
3
4
5
6
30
25
20
10
N/A
N/A
70
65
60
55
50
45
30
25
20
10
N/A
N/A
60
55
50
45
40
30
85
80
75
70
65
60
20
15
N/A
N/A
N/A
N/A
60
55
50
45
40
30
85
80
75
70
65
60
25
20
15
N/A
N/A
N/A
85
80
75
70
65
60
75
70
65
60
55
45
7
N/A
35
N/A
20
50
N/A
20
50
N/A
50
35
8
N/A
25
N/A
10
40
N/A
10
40
N/A
40
25
Minimum
Length
5
5
5
5
20
5
5
20
5
20
5
Three elbows (two in vent pipe and one in the air intake pipe) are already accounted for and need not be included in the elbow count from the Table above.
NOTE: If installing furnace at altitudes between 2000 - 4500 ft.(609.6 1371.6m), intake and vent pipe length must be reduced by 10 ft.
(3.05 m). If the installation requires the maximum allowable
intake and vent pipe length, the furnace must be converted for
high altitude operation. Refer to the proper high altitude application instruction for details.
Example: An 80,000 BTUH (23.5 kW) unit requires 35 ft (10.7 m) of
vent with five elbows. In the Table above, look at the three rows with
80,000 (23.5 kW) in the “Models” column. then look to the right in those
rows to the five elbows column. It shows N/A in the 1-1/2” (3.8 cm) row,
so 1-1/2” (5.1 cm) pipe cannot be used. the 2” (5.1 cm) pipe row shows
40 ft (12.2 m), so up to 40 ft (12.2 m) of 2” (5.1 cm) pipe can be used
with five elbows. The 3” pipe row shows 65 ft (19.8 m), so up to 65 ft
(19.8 m) of 3” (7.62 cm) pipe can be used. Therefore, in this example,
either 2” (5.1 cm) or 3” (7.62 cm) pipe can be used.
COMBUSTION AIR AND VENT PIPING ASSEMBLY
Cut piping to the proper length beginning at the furnace.
2.
Deburr the piping inside and outside.
3.
Chamfer (bevel) the outer edges of the piping.
4.
Dry-fit the vent piping assembly from the furnace to the outside termination checking for proper fit support and slope.
5.
Dry-fit the combustion air piping assembly checking for proper fit,
support and slope on the following systems:
10
Sealed combustion air systems from the furnace to the outside termination.
B.
Ventilated combustion air systems from the furnace to the
attic or crawl space termination.
Solvent cements are flammable and must be used in well-ventilated
areas only. Keep them away from heat, sparks and open flames.
Do not breathe vapors and avoid contact with skin and eyes.
6.
Disassemble the combustion air and vent piping, apply cement
primer and the cement per the manufactures instructions. Primer
and cement must conform to ASTM D2564 for PVC, or ASTM
D2235 for ABS piping.
7.
All joints must provide a permanent airtight and watertight seal.
8.
Support the combustion air and vent piping such that it is angled a
minimum of 1/4” per foot (21 mm/m) so that condensate will flow
back towards the furnace. Piping should be supported with pipe
hangers to prevent sagging.
9.
Seal around the openings where the combustion air and / or vent
piping pass through the roof or sidewalls.
The final assembly procedure for the combustion air and vent piping is
as follows:
1.
A.
COMBUSTION AIR / VENT CLEARANCES
IMPORTANT: The vent must be installed with the following minimum
clearances, and must comply with local codes and requirements.
Unitary Products Group
035-20417-001 Rev. C (0904)
VENT CLEARANCES
G
V
A
D
V
E
B
L V
B
X
AIR SUPPLY
B
B
I
V
C
F
VENT TERMINAL
H
FIXED
CLOSED
V
V
V
V
V
B
B
M
X
V
AREA WHERE TERMINAL IS NOT PERMITTED
K
X
J
FIXED
CLOSED
OPERABLE
FIGURE 11: Home Layout
Canadian Installation1
A.Clearance above grade, veranda, porch, deck, or balcony 12 inches (30 cm)
6 inches (15 cm) for applications ≤ 10,000 Btuh
(3kW), 12 inches (30 cm) for appliances > 10,000
B.Clearance to window or door that may be opened
Btuh (3kW) and ≤ 100,000 Btuh (30kW), 36 inches
(91 cm) for appliances > 100,000 Btuh (30kW)
C.Clearance to permanently closed window
“
D.Vertical clearance to ventilated soffit located
above the terminal within a horizontal distance
“
of 2 feet (61 cm) from the center line of the terminal
E.Clearance to unventilated soffit
“
F. Clearance to outside corner
“
G.Clearance to inside corner
“
H.Clearance to each side of center line extended above
3 feet (91 cm) within a height 15 feet (4.5 m) above
meter/regulator assembly
the meter/regulator assembly
I. Clearance to service regulator vent outlet
3 feet (91 cm)
6 inches (15 cm) for applications ≤ 10,000 Btuh
J. Clearance to nonmechanical air supply inlet to building
(3kW), 12 inches (30 cm) for appliances > 10,000
or the combustion air inlet to any other appliance
Btuh (3kW) and ≤ 100,000 Btuh (30kW), 36 inches
(91 cm) for appliances > 100,000 Btuh (30kW)
K.Clearance to a mechanical supply inlet
6 feet (1.83 m)
L. Clearance above paved sidewalk or paved driveway
located on public property
M.Clearance under veranda, porch, deck, or balcony
Dryer Vent
Plumbing Vent Stack
Gas Appliance Vent Terminal
Vent Termination from any Building Surface
Above Any Grade Level
Above anticipated snow depth
Any forced air inlet to the building.
The vent shall extend above the highest point where it
passes through the roof, not less than
Any obstruction within a horizontal distance
7 feet (2.13 m) †
12 inches (30 cm)
3 ft (91.44 cm)
3 ft (91.44 cm)
3 ft (91.44 cm) *
12" (30.4 cm)
12" (30.4 cm)
12" (30.4 cm)
10 ft (304.8 cm)
US Installation2
12 inches (30 cm)
6 inches (15 cm) for applications ≤ 10,000 Btuh
(3kW), 9 inches (23 cm) for appliances > 10,000 Btuh
(3kW) and ≤ 50,000 Btuh (15kW), 12 inches (30 cm)
for appliances > 50,000 Btuh (30kW)
“
“
“
“
“
“
“
6 inches (15 cm) for applications ≤ 10,000 Btuh
(3kW), 9 inches (23 cm) for appliances > 10,000 Btuh
(3kW) and ≤ 50,000 Btuh (15kW), 12 inches (30 cm)
for appliances > 50,000 Btuh (30kW)
3 feet (91 cm) above if within 10 feet (3 cm)
horizontally
“
‡
“
3 ft (91.44 cm)
3 ft (91.44 cm)
3 ft (91.44 cm) *
12" (30.4 cm)
12" (30.4 cm)
12" (30.4 cm)
10 ft (304.8 cm)
18" (46 cm)
18" (46 cm)
Not less than 18" (46 cm)
Not less than 18" (46 cm)
1.
2.
†
‡
In accordance with the current CSA B149.1-00, Natural Gas and Propane Installation Code.
In accordance with the current ANSI Z223.1 / NFPA 54, National Gas Code.
A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings and serves both dwellings.
Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor. For clearance not specified in ANSI Z223.1 / NFPA
54 or CSA B149.1-00.
Clearance in accordance with local installation codes and the requirements of the gas supplier and the manufacturer’s Installation Manual.
Any fresh air or make up inlet for dryer or furnace area is considered to be forced air inlet.
Avoid areas where condensate drippage may cause problems such as above planters, patios, or adjacent to windows where steam may cause fogging.
A terminus of a vent shall be either:
Fitted with a cap in accordance with the vent manufacturer’s installation instructions, or In accordance with the installation instructions for a special venting system.
* Does not apply to multiple installations of this furnace model. Refer to "VENTING MULTIPLE UNITS" in this section of these instructions.
IMPORTANT: Consideration must be given for degradation of building materials by flue gases. Sidewall termination may require sealing or shielding of building surfaces
with a corrosion resistant material to protect against combustion product corrosion. Consideration must be given to wind direction in order to prevent flue products
and/or condensate from being blown against the building surfaces. If a metal shield is used it must be a stainless steel material at a minimum dimension of 20
inches. It is recommended that a retaining type collar be used that is attached to the building surface to prevent movement of the vent pipe.
Responsibility for the provision of proper adequate venting and air supply for application shall rest with the installer.
Vent shall extend high enough above building, or a neighboring obstruction, so that wind from any direction will not create a positive pressure in the vicinity of the vent.
Unitary Products Group
11
035-20417-001 Rev. C (0904)
VENT SYSTEM
This furnace is certified to be installed with one of two possible vent
configurations.
1.
Horizontal vent system. This vent system can be installed completely horizontal or combinations of horizontal, vertical, or offset
using elbows.
2.
Vertical vent system. This vent system can be installed completely
vertical or a combination of horizontal, vertical, or offset using
elbows.
12” MIN.
12” MIN.
G
AN
H
R
VE
O
HORIZONTAL VENT APPLICATIONS AND
TERMINATION
2.
3.
4.
5.
6.
7.
Observe all clearances listed in vent clearances in these instructions.
Termination should be positioned where vent vapors will not damage plants or shrubs or air conditioning equipment.
Termination should be located where it will not be affected by wind
gusts, light snow, airborne leaves or allow recirculation of flue
gases.
Termination should be located where it will not be damaged or
exposed to flying stones, balls, etc.
Termination should be positioned where vent vapors are not objectionable.
Horizontal portions of the vent system must slope upwards and be
supported to prevent sagging.
Sealed combustion air systems must be installed so the vent and
the combustion air pipes terminate in the same atmospheric zone.
Refer to Figures 14, 15 or 16.
MAINTAIN 12” MINIMUM CLEARANCE
ABOVE HIGHEST ANTICIPATED SNOW
LEVEL. MAXIMUM 24” ABOVE ROOF.
12” MIN.
12” MIN.
12” SEPARATION
BETWEEN BOTTOM
OF COMBUSTION
AIR PIPE AND
BOTTOM OF VENT
MAINTAIN 12”
MINIMUM
CLEARANCE
ABOVE HIGHEST
ANTICIPATED SNOW
LEVEL OR GRADE,
WHICHEVER IS
HIGHER
When selecting the location for a horizontal combustion air / vent termination, the following should be considered:
1.
12” MINIMUM
BELOW
OVERHANG
FIGURE 14: Termination Configuration - 2 Pipe Basement
VERTICAL VENT APPLICATIONS AND
TERMINATION
Roof mounted vertical terminals may be field fabricated. Standard PVC/
SRD fittings may be used. If installing a vertical venting system through
any unconditioned space such as an attic or crawl space it must be
insulated.
1.
Observe all clearances listed in vent clearances in these instructions.
2.
Termination should be positioned where vent vapors are not objectionable.
3.
Termination should be located where it will not be affected by wind
gusts, light snow, or allow recirculation of flue gases.
4.
Termination should be located where it cannot be damaged,
plugged or restricted by tree limbs, leaves and branches.
5.
Horizontal portions of the vent system must slope upwards and be
supported to prevent sagging.
6.
Sealed combustion air systems must be installed so the vent and
the combustion air pipes terminate in the same atmospheric zone.
Refer to Figures 14, 15 or 17.
VENTING MULTIPLE UNITS
Multiple units can be installed in a space or structure as either a single
pipe configuration or a two-pipe configuration.
FIGURE 12: Termination Configuration - 1 Pipe
12” VERTICAL SEPARATION
BETWEEN COMBUSTION AIR
AND VENT
MAINTAIN 12”
MINIMUM
CLEARANCE
ABOVE
HIGHEST
ANTICIPATED
SNOW LEVEL
12” MINIMUM
BELOW OVERHANG
12” SEPARATION
BETWEEN BOTTOM
OF COMBUSTION
AIR PIPE AND
BOTTOM OF VENT
MAINTAIN 12”
MINIMUM CLEARANCE
ABOVE HIGHEST
ANTICIPATED SNOW
LEVEL OR GRADE,
WHICHEVER IS
HIGHER
The combustion air side of the single pipe configuration shown in Figure
20 is referred to in these instructions as ambient combustion air supply.
Follow the instructions for ambient combustion air installations, paying
particular attention to the section on air source from inside the building.
The vent for a single pipe system must be installed as specified in the
venting section of these instructions with the vent terminating as shown
in Figures 16 or 17. Each furnace must have a separate vent pipe.
Under NO circumstances can the two vent pipe be tied together.
The combustion airside of the two-pipe configuration shown in Figure
19 can be installed so the combustion air pipe terminates as described
in outdoor combustion air or ventilated combustion air sections in these
instructions. Follow the instructions for outdoor combustion air or ventilated combustion air and the instructions for installing the vent system
with the vent terminating as shown in Figure 22. The two-pipe system
must have a separate combustion air pipe and a separate vent pipe for
each furnace. Under NO circumstances can the two combustion air or
vent pipes be tied together. The combustion air and vent pipes must terminate in the same atmospheric zone.
FIGURE 13: Termination Configuration - 2 Pipe
12
Unitary Products Group
035-20417-001 Rev. C (0904)
COMBUSTION AIR SUPPLY
All installations must comply with Section 5.3, Air for Combustion and
Ventilation of the National Fuel Gas Code, ANSI Z223.1 or Sections
7.2, 7.3 or 7.4 of CAN/CGA B149.1 or .2 Installation Code - latest editions.
VENT
This furnace is certified to be installed with one of three possible combustion air intake configurations.
1.
COMBUSTION AIR
2”
FIGURE 15: Double Horizontal Sealed Combustion Air and Vent
Termination
2.
6”
3.
OUTDOOR COMBUSTION AIR: This is a sealed combustion air
configuration where the combustion air is supplied through a PVC
or ABS pipe that is connected to the PVC coupling attached to the
burner box and is terminated in the same atmospheric zone as the
vent. This type of installation is approved on all models. Refer to
Figure 19.
AMBIENT COMBUSTION AIR: Combustion air is supplied from
the area surrounding the furnace through vents or knockouts in the
furnace casing. The combustion air and the vent pipes are not terminated in the same atmospheric zone. Refer to Figure 13 for vent
terminations. Refer to “AIR SOURCE FROM INSIDE THE BUILDING” and “VENT AND SUPPLY AIR SAFETY CHECK” for proper
installation. Refer to Figure 20.
VENTILATED COMBUSTION AIR: Combustion air is supplied
through a PVC or ABS pipe that is connected to the PVC coupling
attached to the burner box and is terminated in a ventilated attic or
crawl space. The combustion air and the vent pipes are not terminated in the same atmospheric zone. Refer to Figure 22 for attic
and crawl space termination. Only the combustion air intake may
terminate in the attic. The vent must terminate outside.
FIGURE 16: Double Vertical Sealed Combustion Air and Vent
Termination
Outdoor Combustion Air
EXTERNAL HORIZONTAL VENT DRAIN
This installation requires combustion air to be brought in from outdoors.
This requires a properly sized pipe (Shown in Figure 19) that will bring
air in from the outdoors to the furnace combustion air intake collar on
the burner box. The second pipe (Shown in Figure 19) is the furnace
vent pipe.
When installing the furnace with a horizontal vent configuration it will be
necessary to install an external drain tee in the horizontal portion of the
vent pipe. The drain tee should be as close as possible to the furnace.
This is recommended to prevent accumulation of excess condensate in
the inducer blower or vent pipe during operational cycles. Refer to Figure 18 for recommended external vent drain configuration and connections.
VENT PIPE
Combustion Air Intake/Vent Connections
CONNECTS TO
COLLAR ON TOP
OF BURNER BOX
VENT PIPE CEMENTS
INTO SOCKET JUST
ABOVE TOP PANEL
FIELD SUPPLIED
EXTERNAL VENT
DRAIN
3” MINIMUM
LOOP DIAMETER
MANUFACTURER
SUPPLIED PVC
WYE AND VENT DRAIN
FIGURE 18: Sealed Combustion Air Intake Connection and Vent
Connection
VENT TRAP
TEE
VENT DRAIN
FIGURE 17: External Horizontal Vent Drain
Unitary Products Group
The combustion air intake pipe should be located either through the
wall (horizontal or side vent) or through the roof (vertical vent). Care
should be taken to locate side vented systems where trees or shrubs
will not block or restrict supply air from entering the terminal.
Also, the terminal assembly should be located as far as possible from a
swimming pool or a location where swimming pool chemicals might be
stored. Be sure the terminal assembly follows the outdoor clearances
listed in Section #1 “Outdoor Air Contaminants.”
13
035-20417-001 Rev. C (0904)
Ambient Combustion Air Supply
Combustion Air Source From Outdoors
This type installation will draw the air required for combustion from
within the space surrounding the appliance and from areas or rooms
adjacent to the space surrounding the appliance. This may be from
within the space in a non-confined location or it may be brought into the
furnace area from outdoors through permanent openings or ducts. It is
not piped directly into the burner box. A single, properly sized pipe from
the furnace vent connector to the outdoors must be provided. For
upflow models combustion air is brought into the furnace through the
unit top panel opening. Do not install a pipe into the intake collar on top
of the burner box. Refer to Figure 20.
The blocking effects of louvers, grilles and screens must be given consideration in calculating free area. If the free area of a specific louver or
grille is not known, refer to Table 10, to estimate free area.
TABLE 10: Estimated Free Area
*
+
Wood or Metal
Louvers or Grilles
Wood 20-25%*
Metal 60-70% *
Screens+
1/4” (0.635 cm)
mesh or larger 100%
Do not use less than 1/4” (0.635 cm) mesh.
Free area or louvers and grille varies widely; the installer should follow louver or grille
manufacturer’s instructions.
Dampers, Louvers and Grilles (Canada Only)
COMBUSTION AIR
VENT PIPE CEMENTS
INTO SOCKET JUST
ABOVE TOP PANEL
1.
The free area of a supply air opening shall be calculated by subtracting the blockage area of all fixed louvers grilles or screens
from the gross area of the opening.
2.
Apertures in a fixed louver, a grille, or screen shall have no dimension smaller than 0.25” (6.4 mm).
3.
A manually operated damper or manually adjustable louvers are
not permitted for use.
4.
A automatically operated damper or automatically adjustable louvers shall be interlocked so that the main burner cannot operate
unless either the damper or the louver is in the fully open position
TABLE 11: Free Area
Minimum Free Area Required for Each Opening
FIGURE 19: Combustion Airflow Path Through The Furnace Casing to
the Burner Box
An unconfined space is not less than 50 cu.ft (1.42 m3) per 1,000 Btu/
hr (0.2928 kW) input rating for all of the appliances installed in that
area.
Rooms communicating directly with the space containing the appliances are considered part of the unconfined space, if openings are furnished with doors.
A confined space is an area with less than 50 cu.ft (1.42 m3) per 1,000
Btu/hr (0.2928 kW) input rating for all of the appliances installed in that
area. The following must be considered to obtain proper air for combustion and ventilation in confined spaces.
This type of installation requires that the supply air to the appliance(s) be of a sufficient amount to support all of the appliance(s)
in the area. Operation of a mechanical exhaust, such as an exhaust
fan, kitchen ventilation system, clothes dryer or fireplace may create conditions requiring special attention to avoid unsatisfactory
operation of gas appliances. A venting problem or a lack of supply
air will result in a hazardous condition, which can cause the appliance to soot and generate dangerous levels of CARBON MONOXIDE, which can lead to serious injury, property damage and / or
death.
BTUH Input
Rating
Horizontal Duct
(2,000 BTUH)
Vertical Duct or
Round Duct
Opening to Outside
(4,000 BTUH)
(4,000 BTUH)
40,000
20 sq. in. (51cm)
10 sq. in. (25 cm)
4” (10 cm)
60,000
30 sq. in. (76 cm)
15 sq. in. (38 cm)
5” (13 cm)
80,000
40 sq. in. (102 cm)
20 sq. in. (51 cm)
5” (13 cm)
100,000
50 sq. in. (102 cm)
25 sq. in. (64 cm)
6” (15 cm)
120,000
60 sq. in. (152 cm)
30 sq. in. (76 cm)
7” (18 cm)
140,000
70 sq. in. (178 cm)
35 sq. in. (89 cm)
7” (18 cm)
EXAMPLE: Determining Free Area.
Appliance
1Appliance
2Total Input
100,000 + 30,000 = (130,000 ÷ 4,000) = 32.5 Sq. In. Vertical
Appliance
1Appliance
2Total Input
100,000 + 30,000 = (130,000 ÷ 2,000) = 65 Sq. In. Horizontal
TABLE 12: Unconfined Space Minimum Area in Square Inch
BTUH Input Rating Minimum Free Area Required for Each Opening
40,000
250 (635 cm2)
60,000
375 (953 cm2)
80,000
500 (1270 cm2)
100,000
625 (1588 cm2)
120,000
750 (1905 cm2)
140,000
875 (2222 cm2)
EXAMPLE: Square feet is based on 8 foot ceilings.
28,000 BTUH X 50 Cubic Ft. =
1,400
= 175 Sq. Ft.
1,000
8’ Ceiling Height
14
Unitary Products Group
035-20417-001 Rev. C (0904)
SOFFIT
VENT
VENTILATED
ATTIC
TOP ABOVE
INSULATION
OUTLET
AIR (a)
GAS
WATER
HEATER
FURNACE
OPTIONAL
INLET (a)
AIR SUPPLY OPENINGS AND DUCTS
4. The duct shall terminate within 12 in (30.5 cm) above, and
within 24 in (61 cm) horizontally from, the burner level of
the appliance having the largest input.
GAS
VENT
GABLE
VENT
5. A square or rectangular shaped duct shall only be used
when the required free area of the supply opening is
2
2
9 in (58.06 cm ) or larger. When a square or rectangular
duct is used, its small dimensionshall not be less than
3 in (7.6 cm).
VENTILATED
ATTIC
TOP ABOVE
INSULATION
INLET
AIR (b)
GAS
WATER
HEATER
FURNACE
6. An air inlet supply from outdoors shall be equipped with SOFFIT
a means to prevent the direct entry of rain and wind.
VENT
Such means shall not reduce the required free area of
the air supply opening.
An air supply inlet opening from the outdoors shall
be located not less than 12” (30.5 cm) above the
outside grade level.
INLET
AIR (b)
OUTLET
AIR (a)
GAS
WATER
HEATER
INLET
AIR (a)
COMBUSTION AIR SOURCE FROM OUTDOORS
VENTILATED
CRAWL SPACE
7.
GAS
VENT
1. An opening may be used in lieu of a duct to provide to provide the outside air
supply to an appliance unless otherwise permitted by the authority having
jurisdiction. The opening shall be located within 12” (30.5 cm) horizontally from,
the burner level of the appliance. Refer to “AIR SOURCE FROM OUTDOORS
AND VENT AND SUPPLY AIR SAFETY CHECK” in these instructions for
additional information and safety check procedure.
OUTLET
2. The duct shall be either metal, or a material meeting the class 1
AIR (b)
requirements of CAN4-S110 Standard for Air Ducts.
The
duct
shall
be
least
the
same
cross-sectional
area
as
the
free
3.
area of the air supply inlet opening to which it connects.
FURNACE
GAS
VENT
GABLE
VENT
1. Two permanent openings, one within 12 in (30.5 mm) of the top and
one within 12 in (30.5 mm) of bottom of the confined space, Two
permanent openings, shall communicate directly or by means of ducts
with the outdoors, crawl spaces or attic spaces.
2. One permanent openings, commencing within 12 in (30.5 mm)of the
top of the enclosure shall be permitted where the equipment has
clearances of at least 1 in (2.54 cm) from the sides and back and
6 in (15.24 cm) from the front of the appliance. The opening shall
communicate directly with the outdoors and shall have a minimum
free area of:
a. 1 square in per 3000 Btu per hour (6.45 cm3 per 0.879 kW) of the
total input rating of all equipment located in the enclosure.
b. Not less than the sum of all vent connectors in the confined space.
3. The duct shall be least the same cross-sectional area as the free
area of the air supply inlet opening to which it connects.
INLET 4. The blocking effects of louvers, grilles and screens must be given
AIR (a)
consideration in calculating free area. If the free area of a specific
louver aor grille is not known.
FIGURE 20: Outside and Ambient Combustion Air
Vent and Supply (Outside) Air Safety Check Procedure
Follow the procedure in ANSI Z223.1 National Fuel Gas Code. Refer to
the section on the “Recommended Procedure for Safety Inspection of
an Existing Appliance” or in Canada B149.1-00 Natural Gas and Propane Installation Code section on “Venting Systems and Air Supply for
Appliances” and all local codes. In addition to the procedure specified in
ANSI Z223.1, It is recommended that you follow the venting safety procedure below. This procedure is designed to detect an inadequate ventilation system that can cause the appliances in the area to operate
improperly causing unsafe levels of Carbon Monoxide or an unsafe
condition to occur.
1.
Inspect the venting system for proper size and horizontal pitch.
Determine that there is no blockage, restriction, leakage, corrosion
or other deficiencies, which could cause an unsafe condition
2.
Close all building doors and windows and all doors.
3.
Turn on clothes dryers and TURN ON any exhaust fans, such as
range hoods and bathroom exhausts, so they shall operate at
maximum speed. Open the fireplace dampers. Do not operate a
summer exhaust fan.
4.
Follow the lighting instructions. Place the appliance being
inspected in operation. Adjust thermostat so the appliance shall
operate continuously.
5.
Test each appliance (such as a water heater) equipped with a draft
hood for spillage (down-draft or no draft) at the draft hood relief
opening after 5 minutes of main burner operation. Appliances that
do not have draft hoods need to be checked at the vent pipe as
close to the appliance as possible. Use a combustion analyzer to
check the CO2 and CO levels of each appliance. Use a draft
gauge to check for a downdraft or inadequate draft condition.
6.
After it has been determined that each appliance properly vents
when tested as outlined above, return doors, windows, exhaust
fans, fireplace dampers and any other gas burning appliance to
their normal condition.
7.
If improper venting is observed during any of the above tests, a
problem exists with either the venting system or the appliance
does not have enough combustion air (Supply Air from outside) to
complete combustion. This condition must be corrected before the
appliance can function safely.
Unitary Products Group
NOTE: An unsafe condition exists when the CO reading exceeds 100
ppm and the draft reading is not in excess of - 0.1 in. W.C. (-25
kPa) with all of the appliance(s) operating at the same time.
8. Any corrections to the venting system and / or to the supply (outside) air system must be in accordance with the National Fuel Gas
Code Z223.1 or CAN/CGA B149.1-00 Natural Gas and Propane
Installation Code (latest editions). If the vent system must be
resized, follow the appropriate tables in Appendix G of the above
codes or for this appliance only refer to Table 9 of these instructions.
Ventilated Combustion Air
The ventilated attic space or a crawl space from which the combustion
air is taken must comply with the requirements specified in “AIR
SOURCE FROM OUTDOORS” in this instruction or in Section 5.3, Air
for Combustion and Ventilation of the National Fuel Gas Code, ANSI
Z223.1 (latest edition). This type installation requires two properly sized
pipes. One brings combustion air from a properly ventilated attic space
or crawl space and a second pipe that extends from the furnace vent
connection (top right of unit) to the exterior of the building. Refer to
Table 9 for intake pipe sizing, allowable length and elbow usage. Follow
all notes, procedures and required materials in the SEALED COMBUSTION AIR SUPPLY section in these instructions when installing the
combustion air pipe from the unit and into a ventilated attic space or
crawl space. DO NOT terminate vent pipe in an Attic or Crawl Space.
Ventilated Combustion Air Termination
Refer to Figure 22 for required attic termination for the combustion air
intake pipe. For attic termination, use two 90 elbows with the open end
in a downward position. Be sure to maintain 12” (30 cm) clearance
above any insulation, flooring or other material.
A crawl space combustion air installation consists of a straight pipe from
the PVC coupling on the burner box that extends into the crawl space
and terminates with a 1/4” (6.35 mm) mesh screen and no elbows.
15
035-20417-001 Rev. C (0904)
12” MINIMUM
BETWEEN BOTTOM
OF BELOW AND
ANY MATERIAL
2.
3.
Elevate this hose and fill with water using a funnel.
Replace the condensate drain hose and clamps.
IMPORTANT: If this procedure is not followed, the unit may not properly
drain on initial start up.
12”
MIN.
CONDENSATE DRAIN TERMINATION
DO NOT terminate condensate drain in a chimney, or where the drain
line may freeze. The line must terminate at an inside drain to prevent
freezing of the condensate and possible property damage.
DO NOT trap the drain line at any other location than at the condensate
drain trap supplied with the furnace.
FIGURE 21: Attic and Crawl Space Combustion Air Termination
Specially Engineered Installations
The above requirements shall be permitted to be waived where special
engineering, approved by the authority having jurisdiction, provides an
adequate supply of air for combustion, ventilation and dilution of flue
gases.
Be sure to instruct the owner not to block this intake pipe.
SECTION VII: CONDENSATE PIPING
The condensate drain connection is provided in the furnace for field
installation. It consists of a formed hose with a 1/2” (1.3 cm) NPT male
connection. A 1/2” (1.3 cm) FM x 3/4” (1.9 cm) PVC slip coupling is provided.
This drain hose may be installed to allow left or right side condensate
drain connection, refer to Figure 23. Cut the hose to allow for proper fit
for left or right exit. If necessary, trim the hose supplied to ensure that it
slopes downwards.
OPEN
TEE
OPEN
TEE
LH
DRAIN
RH
DRAIN
A condensate sump pump MUST be used if required by local codes, or
if no indoor floor drain is available. The condensate sump pump must
be approved for use with acidic condensate.
CONDENSATE DRAIN TRAP AND DRAIN FREEZE
PROTECTION
Special precautions MUST be made if installing furnace in an area
which may drop below freezing. This can cause improper operation or
damage to the equipment. If the furnace is installed in an area that has
the potential of freezing, the drain line and the drain trap must be protected. Use a 3 to 6 watt per foot (0.003 to 0.006 kW per meter) at 115
vac, 40º F (4.4° C) self-regulating, shielded and waterproof heat tape.
Wrap the drain trap and the drain line with the heat tape and secure
with ties. Follow the heat tape manufacturer's recommendations.
SECTION VIII: SAFETY CONTROLS
CONTROL CIRCUIT FUSE
A 3-amp fuse is provided on the control circuit board to protect the 24volt transformer from overload caused by control circuit wiring errors.
This is an ATO 3, automotive type fuse and is located on the control
board.
BLOWER DOOR SAFETY SWITCH
This unit is equipped with an electrical interlock switch mounted in the
blower compartment. This switch interrupts all power at the unit when
the panel covering the blower compartment is removed.
Electrical supply to this unit is dependent upon the panel that covers the
blower compartment being in place and properly positioned.
Main power to the unit must still be interrupted at the main power
disconnect switch before any service or repair work is to be done to
the unit. Do not rely upon the interlock switch as a main power disconnect.
Blower and burner must never be operated without the blower
panel in place.
FIGURE 22: Condensate Piping
To install the drain hose assembly, remove the 7/8” (2.2 cm) knockout in
the side panel. Remove the conduit nut from the 1/2” (1.3 cm) male fitting. Push the male fitting through the hole and reinstall the nut. The
use of the 3/4” (1.9 cm) PVC coupling is optional.
The condensate water will flow to the drain better if an open tee, or
short length of pipe is installed in the drain line, as shown in Figure 23.
IMPORTANT: The condensate drain from the furnace may be connected in common with the drain from an air conditioning coil if allowed
by local code.
IMPORTANT: Condensate must be disposed of properly. Follow local
plumbing or wastewater codes. The drain line must maintain a 1/4" per
foot (0.635 cm per meter) slope to the drain.
CONDENSATE DRAIN
The condensate trap must be filled with water before putting the furnace
into operation. Perform the following procedures only after the condensate trap has been properly piped to a drain connection using the procedure in this instruction.
The recommended procedure is as follows:
1.
16
Disconnect the condensate drain hose from the induced draft
blower discharge.
ROLLOUT SWITCH CONTROLS
These controls are mounted on the burner box assembly. If the temperature in the burner box exceeds its set point, the ignition control and the
gas valve are de-energized. The operation of this control indicates a
malfunction in the combustion air blower, heat exchanger or a blocked
vent pipe connection. Corrective action is required. These are manual
reset controls that must be reset before operation can continue.
PRESSURE SWITCHES
This furnace is supplied with two pressure switches, which monitor the
flow through the combustion air/vent piping system. These switches deenergize the ignition control module and the gas valve if any of the following conditions are present. Refer to Figure 24 for tubing connections.
1.
2.
3.
4.
Blockage of combustion air piping or terminal.
Blockage of vent piping or terminal.
Failure of combustion air blower motor.
Blockage of condensate drain piping.
Unitary Products Group
035-20417-001 Rev. C (0904)
LIMIT CONTROLS
There is high temperature limit control located on the furnace vestibule
panel near the gas valve. This is an automatic reset control that provides over temperature protection due to reduced airflow, that may be
caused by a dirty filter, or if the indoor fan motor should fail. The control
module will lockout if the limit trips 5 consecutive times within a single
call for heat. Control will reset and try ignition again after 1 hour.
There is a accessory kit (1PK0602) available from Source 1, which has
the following items:
• 12” (30 cm) length x 1/8” (0.3 cm) diameter tubing
• 2 – pieces of 4” (10 cm) length x 1/8” (0.3 cm) diameter tubing
• 1 - 5/16” (0.8 cm) tee
• 1 – 5/16” (0.8 cm) x 1/8” (0.3 cm) reducing coupling
• 1 – 1/8” (0.3 cm) adapter
• 1 - Dwyer – Manometer
These items are required in order to properly perform the required startup procedure.
IGNITION SYSTEM SEQUENCE
1.
Turn the gas supply ON at external valve and main gas valve.
2.
Set the thermostat above room temperature to call for heat.
3.
System start-up will occur as follows:
a.
The induced draft blower motor will start and come up to
speed. Shortly after inducer start-up, the hot surface igniter
will glow for about 17 seconds.
FIGURE 23: Pressure Switch Tube Routing
b.
SECTION IX: START-UP AND
ADJUSTMENTS
After this warm up, the ignition module will energize (open)
the main gas valve.
c.
After flame is established, the supply air blower will start in
about 30 seconds.
The initial start-up of the furnace requires the following additional
procedures:
IMPORTANT: All electrical connections made in the field and in the factory should be checked for proper tightness.
When the gas supply is initially connected to the furnace, the gas piping
may be full of air. In order to purge this air, it is recommended that the
ground union be loosened until the odor of gas is detected. When gas is
detected, immediately retighten the union and check for leaks. Allow
five minutes for any gas to dissipate before continuing with the start-up
procedure. Be sure proper ventilation is available to dilute and carry
away any vented gas.
Perform the following procedures only after the condensate trap
has been properly piped to a drain connection using the procedure
in this instruction.
TOOLS AND INFORMATION THAT WILL BE
REQUIRED IN ORDER TO PROPERLY PERFORM THE
FURNACE STARTUP PROCEDURE.
1.
Call the local gas supplier to obtain heating value of the natural
gas. If you cannot obtain the heating valve of the gas from the gas
supplier, you may use a default value of 1030 BTU/SCF (38.8 MJ /
m³).
2.
You will need a thermometer or portable digital thermometer to
read the supply and return air temperatures.
3.
You will need a U-tube manometer or digital equipment that has
the ability to read pressures between 0 – 15” in.w.c (0 - 3.73 kPa)
in order to measure the gas line and the manifold pressures.
4.
You will need a 3/32” Allen wrench for the pressure port plugs in
the gas valve.
5.
You will need 2 pieces of 1/8” (0.3 cm) ID flexible tubing that is 12”
(30 cm) in length, 2 – pieces of 1/8” (0.3 cm) tubing that are 4”
(10.0 cm) in length, a 1/8” (0.3 cm) tee and a 1/8” (0.3 cm) adapter
to connect the U-tube manometer or the digital pressure measuring equipment to the gas valve pressure ports.
There is an accessory kit (1PK0601) available from Source 1, which
has the following items:
• 1 - 12” (30 cm) length x 1/8” (0.3 cm) diameter tubing
• 2 – pieces of 4” (10 cm) length x 1/8” (0.3 cm) diameter tubing
• 1 - 5/16” (0.8 cm) tee
• 1 – 5/16” (0.8 cm) x 1/8” (3.175 mm) reducing coupling
• 1 – 1/8” (0.3 cm) adapter
Unitary Products Group
FIRE OR EXPLOSION HAZARD
Failure to follow the safety warnings exactly could result in serious
injury, death or property damage.
Never test for gas leaks with an open flame. Use a commercially
available soap solution made specifically for the detection of leaks
to check all connections. A fire or explosion may result causing
property damage, personal injury or loss of life.
IMPORTANT: Burner ignition may not be satisfactory on first startup
due to residual air in the gas line or until gas manifold pressure is
adjusted. The ignition control will make 3 attempts to light before locking out.
With furnace in operation, check all of the pipe joints, gas valve connections and manual valve connections for leakage using an approved gas
detector, a non-corrosive leak detection fluid, or other leak detection
methods. Take appropriate steps to stop any leak. If a leak persists,
replace the component.
The furnace and its equipment shutoff valve must be disconnected from
the gas supply piping system during any pressure testing of that system
at test pressures in excess of 1/2 PSI (3.45 kPa).
The furnace must be isolated from the gas supply piping system by
closing the equipment shutoff valve during any pressure testing of the
gas supply piping system.
CALCULATING THE FURNACE INPUT
(NATURAL GAS)
NOTE: Burner orifices are sized to provide proper input rate using natural gas with a heating value of 1050 BTU/Ft3 (39.12 MJ/m3). If
the heating value of your gas is significantly different, it may be
necessary to replace the orifices.
NOTE: Front door of burner box must be secured when checking gas
input.
1. Turn off all other gas appliances connected to the gas meter.
2. At the gas meter, measure the time (with a stop watch) it takes to
use 2 cubic ft. (0.0566 m3.) of gas.
3. Calculate the furnace input by using one of the following equations.
17
035-20417-001 Rev. C (0904)
In the USA use the following formula to calculate the furnace input.
For natural gas multiply the heat content of the gas BTU/SCF (or Default 1030 BTU/SCF (38.4 MJ/m3), times 2 cubic ft. (0.056 m) of gas measured
at the gas meter, times a barometric pressure and temperature correction factor of 0.960; times 3600, then divided by the time (In seconds) it took to
measure 2 cubic ft. (0.056 m) of gas from the gas meter.
For propane (LP) gas multiply the heat content of the gas BTU/SCF (or Default 2500 BTU/SCF (93.15 MJm3), times 1 cubic ft. (0.028 m) of gas measured at the gas meter, times a barometric pressure and temperature correction factor of 0.960; times 3600, then divided by the time (In seconds) it
took to measure 1 cubic ft. (0.028 m) of gas from the gas meter.
The formula for US input calculation using a cubic foot gas meter:
BTU/f3 x 2 cu.ft. x 0.960 x 3600
Seconds it took to measure the 2 cu.ft. of gas
NATURAL GAS INPUT CALCULATION
EXAMPLE:
1030 x 2 x 0.960 x 3600
90.5
Natural Gas
BTU/SCF 1030
=
BTU/H
=
79,997.38
BTU/f3 x 2 cu.ft. x 0.960 x 3600
Seconds it took to measure the 2 cu.ft. of gas
PROPANE (LP) GAS INPUT CALCULATION
EXAMPLE:
2500 x 1 x 0.960 x 3600
108
Propane Gas
BTU/SCF 2500
=
BTU/H
=
80,000.00
In Canada you will use the following formula to calculate the furnace input if you are using a cubic foot gas meter.
For Natural Gas multiply the Heat content of the gas MJ/m3 (or Default 39.2), times 2 cubic ft. of gas x 0.02831 to convert from cubic feet to cubic
meters measured at the gas meter, times a barometric pressure and temperature correction factor of 0.960; times 3600, then divided by the time it
took to measure 2 cubic ft. (0.056 m) of gas from the gas meter.
For Propane (LP) Gas multiply the Heat content of the gas MJ/m3 (or Default 93.14), times 1 cu. ft. of gas x 0.02831 to convert from cubic feet to
cubic meters measured at the gas meter, times a barometric pressure and temperature correction factor of 0.960; times 3600, then divided by the
time it took to measure 1 cubic ft. (0.028 m) of gas from the gas meter.
The formula for metric input calculation using a cubic foot gas meter:
MJ/m3 x (2 cu.ft. x 0.028) x 0.960 x 3600
Seconds it took to measure the 2 cu.ft. of gas
NATURAL GAS INPUT CALCULATION
EXAMPLE:
39.2 x (2 x 0.028) x 0.960 x 3600
90.5
Natural Gas
BTU/SCF 1030 = 39.2 MJ/m3
PROPANE (LP) GAS INPUT CALCULATION
EXAMPLE:
93.15 x (1 x 0.028) x 0.960 x 3600
108
Propane Gas
BTU/SCF 2500 = 93.15 MJ/m3
=
MJ/H
x
0.2777
=
kW
x
3412.14
=
BTU/H
=
84.83
x
0.2777
=
23.28
x
3412.14
=
79,433
=
84.41
x
0.2777
=
23.45
x
3412.14
=
80,000.00
In Canada use the following formula to calculate the furnace input if you are using a gas meter that measures cubic meters.
For Natural Gas multiply the Heat content of the gas MJ/m3 (or Default 39.2), times 0.0566 m3 of gas measured at the gas meter, times a barometric
pressure and temperature correction factor of 0.960; times 3600, then divided by the time it took to measure 2 cubic ft. (0.0566 m3) of gas from the
gas meter.
For Propane (LP) Gas multiply the Heat content of the gas MJ/m3 (or Default 93.14), times 0.00283 m3 of gas measured at the gas meter, times a
barometric pressure and temperature correction factor of 0.960; times 3600, then divided by the time it took to measure 1 cubic ft. (0.0283 cm) of gas
from the gas meter.
The formula for metric input calculation using a cubic foot gas meter:
MJ/m3 x m3 x 0.960 x 3600
Seconds it took to measure the 2 cu.ft. of gas
NATURAL GAS INPUT CALCULATION
EXAMPLE:
39.2 x 0.1 x 0.960 x 3600
160
Natural Gas
BTU/SCF 1030 = 39.2 MJ/m3
PROPANE (LP) GAS INPUT CALCULATION
EXAMPLE:
93.15 x 0.028 x 0.960 x 3600
107.97
Propane Gas
BTU/SCF 2500 = 93.15 MJ/m3
=
MJ/H
x
0.2777
=
kW
x
3412.14
=
BTU/H
=
84.67
x
0.2777
=
23.51
x
3412.14
=
80,231
=
84.48
x
0.2777
=
23.18
x
3412.14
=
79,107
DO NOT ADJUST the manifold pressure regulator if the actual input is equal to or within 8% less than the furnace input specified on the rating plate
or if the furnace rise is above the specified rise range on the rating plate.
If the actual input is significantly higher than the furnace input specified on the rating plate then replace the gas orifice spuds with the gas orifice spuds of the proper size for the type of gas you are using.
For altitudes above 2,000 ft. (610 m) the furnace input MUST BE DERATED. Refer to the GAS CONVERSION FOR PROPANE (LP) AND HIGH
ALTITUDES IN SECTION IV for information on high altitude conversions.
18
Unitary Products Group
035-20417-001 Rev. C (0904)
IMPORTANT: The cap for the pressure regulator must be removed
entirely to gain access to the adjustment screw. Loosening or tightening
the cap does not adjust the flow of gas.
Be sure to relight any gas appliances that were turned off at the
start of this input check.
1.
Refer to Figure 24 for location of pressure regulator adjustment
cap and adjustment screws on main gas valve.
2.
Turn gas and electrical supplies on and follow the operating
instructions to place the unit back in operation.
3.
Adjust manifold pressure by adjusting gas valve regulator screw
for the appropriate gas per the following:
TABLE 13: Inlet Gas Pressure Range
INLET GAS PRESSURE RANGE
Minimum
Maximum
Natural Gas
4.5” W.C. (1.12 kPa)
10.5” W.C. (2.61 kPa)
Propane (LP)
8.0” W.C. (1.99 kPa)
13.0” (3.24 kPa) W.C.
TABLE 14: Nominal Manifold Pressure
NOMINAL MANIFOLD PRESSURE
IMPORTANT: The inlet gas pressure operating range table specifies
what the minimum and maximum gas line pressures must be for the furnace to operate safely. The gas line pressure MUST BE
• 7” W.C. (1.74 kPA) for Natural Gas
• 11” W.C. (2.74 kPA) for Propane (LP) Gas
in order to obtain the BTU input specified on the rating plate and/or the
nominal manifold pressure specified in these instructions and on the
rating plate.
Turn gas off at the ball valve or gas cock on gas supply line
before the gas valve. Find the pressure ports on the gas
valve marked OUT P and IN P.
1.
The manifold pressure must be taken at the port marked OUT P.
2.
The inlet gas line pressure must be taken at the port marked IN P.
3.
Using a 3/32” (2.4 mm) Allen wrench, loosen the setscrew by turning it 1 turn counter clockwise. DO NOT REMOVE THE SET
SCREW FROM THE PRESSURE PORT.
Read the inlet gas pressure using either of the two
methods below.
Disconnect the pressure reference hose from the right side of
the burner box. Using a tee fitting and a short piece of hose,
connect the negative side of the manometer to the burner
box as described below.
B.
Remove one end the 5/16” (7.94 mm) ID flexible tubing over
the pressure port on the burner box.
C.
Insert the end of the 5/16” (7.94 mm) tubing, that has the 1/8”
(3.175 mm) adapter at the end of the tube, in to the 1/8”
(3.175 mm) tee.
D.
Connect the 1/8” (3.175 mm) tee to the burner box adapter
and to the negative side of a U-tube manometer or digital
pressure measuring equipment with 2 – 1/8” (3.175 mm)
tubes.
E.
Use the 5/16” (7.94 mm x 1/8” (3.175 mm) reducing coupling
and a 4” (101.6 mm) piece of 1/8” (3.175 mm) tubing to connect the positive side of the manometer to the gas valve pressure reference port. Refer to Figure 26 for connection details.
Reading the gas pressure with the burner box cover removed Remove the screws securing the burner box front cover plate. Remove
the cover. The gasket and may stick in place. Connect the positive side
of the manometer to the gas valve as described in E above. There will
be no second connection to the manometer, as it will reference atmospheric pressure. Refer to Figure 25 for connection details.
This gas valve has separate regulator adjustment screws for high fire
and low fire, as shown in Figure 24. The procedure below is used to
adjust either the high fire manifold pressure or the low fire manifold
pressure.
Unitary Products Group
1.6" w.c. (0.40 kPa)
Propane (LP) Gas (High Fire)
10.0" w.c. (2.488 kPa)
Propane (LP) Gas (Low Fire)
4.0" w.c. (0.99 kPa)
HIGH STAGE REGULATOR
ADJUSTMENT
VENT
PORT
INLET
OUTLET
WRENCH
BOSS
INLET
PRESSURE
PORT
ON OFF
SWITCH
LOW STAGE REGULATOR
ADJUSTMENT
FIGURE 24: Gas Valve
IMPORTANT: If gas valve regulator is turned in (clockwise), manifold
pressure is increased. If screw is turned out (counterclockwise), manifold pressure will decrease.
4.
After the manifold pressure has been adjusted, re-calculate the
furnace input to make sure you have not exceeded the specified
input on the rating plate. Refer to “CALCULATING THE FURNACE
INPUT (NATURAL GAS)”.
5.
Once the correct BTU (kW) input has been established, turn the
gas valve to OFF and turn the electrical supply switch to OFF; then
remove the flexible tubing and fittings from the gas valve pressure
tap and the pressure reference hose from the right side of the
burner box and tighten the pressure tap plug using the 3/32”
(2.4 mm) Allen wrench. Replace the burner box front cover (if it
was removed) and place the pressure reference hose back on the
gas valve.
6.
Turn the electrical and gas supplies back on, and with the burners
in operation, check for gas leakage around the gas valve pressure
port for leakage using an approved gas detector, a non-corrosive
leak detection fluid, or other leak detection methods.
Reading the gas pressure with the burner box cover in place:
A.
3.5" w.c. (0.87 kPa)
Natural Gas (Low Fire)
OUTLET
PRESSURE
PORT
ADJUSTMENT OF MANIFOLD GAS PRESSURE
Manifold gas pressure may be measured by two different procedures. It
may be measured with the burner box cover in place or it may be measured with the burner box cover removed. Follow the appropriate section in the instructions below. Refer to Figure 24 for a drawing of the
locations of the pressure ports on the gas valve.
Natural Gas (High Fire)
The manifold pressure must be checked with the screw-off cap for
the gas valve pressure regulator in place. If not, the manifold pressure setting could result in an over-fire condition. A high manifold
pressure will cause an over-fire condition, which could cause premature heat exchanger failure. If the manifold pressure is too low,
sooting and eventual clogging of the heat exchanger could occur.
Be sure that gas valve regulator cap is in place and burner box to
gas valve pressure reference hose is connected.
19
035-20417-001 Rev. C (0904)
WITH BURNER BOX COVER IN PLACE
WITH BURNER BOX COVER REMOVED
BURNER BOX
PRESSURE
REFERENCE
HOSE
BURNER BOX
PRESSURE
REFERENCE
HOSE
(not used)
TEE
FITTING
BURNER BOX
WITH COVER
REMOVED
BURNER BOX
WITH COVER
OUTLET
PRESSURE
TAP
GAS VALVE
U-TUBE
MANOMETER
6
5
4
3
2
1
0
1
2
3
4
5
6
3.5 IN
WATER
COLUMN
GAS PRESSURE
SHOWN
U-TUBE
MANOMETER
6
5
4
3
2
1
0
1
2
3
4
5
6
OUTLET
PRESSURE
TAP
GAS VALVE
3.5 IN
WATER
COLUMN
GAS PRESSURE
SHOWN
FIGURE 25: Reading Gas Pressure
ADJUSTMENT OF TEMPERATURE RISE
The temperature rise, or temperature difference between the return
air and the supply (heated) air from the furnace, must be within the
range shown on the furnace rating plate and within the application
limitations shown in Table 7 “ELECTRICAL AND PERFORMANCE
DATA”.
The supply air temperature cannot exceed the “Maximum Supply
Air Temperature” specified in these instructions and on the furnace rating plate. Under NO circumstances can the furnace be
allowed to operate above the Maximum Supply Air Temperature.
Operating the furnace above the Maximum Supply Air Temperature
will cause premature heat exchanger failure, high levels of Carbon
Monoxide, a fire hazard, personal injury, property damage, and/or
death.
The temperature rise, or temperature difference between the return air
and the heated supply air from the furnace, must be within the range
shown on the furnace rating plate and within the application limitations
shown in Table 7.
This furnace is equipped with a time-on/time-off heating fan control. The
fan on delay is fixed at 30 seconds. The fan off delay has 4 settings (60,
90, 120 and 180 seconds). The fan off delay is factory set to 120 seconds. The fan-off setting must be long enough to adequately cool the
furnace, but not so long that cold air is blown into the heated space. The
fan-off timing may be adjusted by positioning the jumper on two of the
four pins as shown in Figure 27.
The furnace control board also allows user selection of the blower
speed that is energized during continuous fan operation. Place jumper
on the HI COOL, LO COOL, or HEAT pins.
BLOWER OFF
DELAY JUMPER
W2 DELAY
JUMPER
CONTINUOUS
FAN SPEED
JUMPER
Y2 W1
Y W
W2
R
G
C
All direct-drive blowers have multi-speed motors. The blower motor
speed taps are located in the control box in the blower compartment.
Refer to Figure 27, and the unit-wiring label to change the blower
speed. To use the same speed tap for heating and cooling, the heat terminal and cool terminal must be connected using a jumper wire and
connected to the desired motor lead. Place all unused motor leads on
Park terminals. Two are provided.
ADJUSTMENT OF FAN CONTROL SETTINGS
Y1
After about 20 minutes of operation, determine the furnace temperature
rise. Take readings of both the return air and the heated air in the ducts,
about six feet (1.83 m) from the furnace where they will not be affected
by radiant heat. Increase the blower speed to decrease the temperature
rise; decrease the blower speed to increase the rise.
Do not energize more than one motor speed at a time or damage to
the motor will result.
FIGURE 26: Furnace Control Board
20
Unitary Products Group
035-20417-001 Rev. C (0904)
TABLE 15: Blower Performance CFM
AIRFLOW WITH BOTTOM OR ONE SIDE RETURN
MODELS
Input/
Airflow/cabinet
40/1200/A
80/1200/B
60/1200/B
100/2000/C
100/1600/C
80/1600/C
120/2000/D
EXTERNAL STATIC PRESSURE, INCHES W.C. (kPa)
Speed
Tap
0.1 (0.025)
0.2 (0.050)
0.3 (0.075)
0.4 (0.099)
0.5 (0.124)
0.6 (0.149)
0.7 (0.174)
0.8 (0.199)
0.9 (0.224)
1.0 (0.249)
CFM m3/min CFM m3/min CFM m3/min CFM m3/min CFM m3/min CFM m3/min CFM m3/min CFM m3/min CFM m3/min CFM m3/min
HIGH
1395
40
1330
38
1265
36
1200
34
1120
32
1030
29
940
27
820
23
NR
NR
NR
M-HI
1025
29
990
28
960
27
925
26
885
25
825
23
750
21
660
19
NR
NR
NR
NR
NR
M-LO
785
22
765
22
745
21
715
20
670
19
625
18
545
15
NR
NR
NR
NR
NR
NR
LOW
640
18
605
17
590
17
565
16
530
15
465
13
405
11
NR
NR
NR
NR
NR
NR
HIGH
1650
47
1605
45
1570
44
1525
43
1465
41
1410
40
1350
38
1275
36
1170
33
1060
30
M-HI
1165
33
1185
34
1175
33
1165
33
1150
33
1140
32
1100
31
1050
30
970
27
875
25
M-LO
895
25
915
26
935
26
940
27
940
27
920
26
905
26
860
24
815
23
750
21
LOW
710
20
725
21
725
21
725
21
720
20
700
20
685
19
660
19
625
18
560
16
HIGH
2300
65
2210
63
2120
60
2020
57
1930
55
1830
52
1715
49
1595
45
1480
42
1350
39
M-HI
1950
55
1900
54
1830
52
1755
50
1680
48
1595
45
1500
42
1390
39
1270
36
1155
33
M-LO
1610
46
1545
44
1490
42
1440
41
1390
39
1315
37
1230
33
1155
33
1050
30
920
26
LOW
1325
38
1270
36
1225
35
1175
33
1105
31
1045
30
990
28
905
25
890
25
790
22
HIGH
1960
56
1955
55
1925
55
1890
54
1830
52
1765
50
1695
48
1615
46
1600
45
1485
42
M-HI
1565
44
1560
44
1560
44
1575
45
1545
44
1530
43
1475
42
1425
40
1365
39
1260
36
M-LO
1230
35
1275
36
1285
36
1300
37
1310
37
1300
37
1280
36
1245
35
1190
34
1070
30
LOW
930
26
945
27
965
27
975
28
975
28
975
28
975
28
950
27
910
26
850
24
HIGH
2560
72
2485
70
2410
68
2320
66
2220
63
2135
60
2035
58
1920
54
1785
51
1650
47
M-HI
2090
59
2050
58
1990
56
1970
56
1885
53
1820
52
1760
50
1675
47
1545
44
1405
40
M-LO
1695
48
1675
47
1665
47
1615
46
1565
44
1510
43
1460
41
1385
39
1285
36
1140
32
LOW
1175
33
1150
33
1135
32
1110
31
1085
31
1055
30
1005
28
980
28
970
27
845
24
AIRFLOW WITH TWO SIDE RETURNS OR WITH BOTTOM AND ONE SIDE RETURN
MODELS
Input/
Airflow/cabinet
100/2000/C
120/2000/D
EXTERNAL STATIC PRESSURE, INCHES W.C. (kPa)
Speed
Tap
0.1 (0.025)
0.2 (0.050)
0.3 (0.075)
0.4 (0.099)
0.5 (0.124)
0.6 (0.149)
0.7 (0.174)
0.8 (0.199)
0.9 (0.224)
1.0 (0.249)
CFM m3/min CFM m3/min CFM m3/min CFM m3/min CFM m3/min CFM m3/min CFM m3/min CFM m3/min CFM m3/min CFM m3/min
HIGH
2465
70
2380
67
2295
65
2195
62
2095
59
1995
56
1875
53
1760
50
1620
46
1470
M-HI
2085
59
2035
58
1960
55
1880
54
1800
51
1705
48
1605
45
1485
42
1360
39
1235
42
35
M-LO
1725
49
1625
46
1595
45
1540
44
1485
42
1405
40
1315
37
1235
35
1125
32
995
28
LOW
1420
40
1360
39
1310
37
1255
36
1180
33
1120
32
1070
30
970
27
950
27
845
24
HIGH
2615
74
2535
72
2450
69
2385
68
2285
65
2175
62
2075
59
1945
55
1825
52
1670
47
M-HI
2055
58
2045
58
2015
57
1985
56
1932
55
1855
53
1785
51
1730
49
1605
45
1470
42
M-LO
1690
48
1650
47
1620
46
1600
45
1570
44
1525
43
1470
42
1395
40
1300
37
1200
34
LOW
1345
38
1335
38
1335
38
1285
36
1250
35
1230
35
1180
33
1115
32
1010
29
850
24
NOTES:
1. Airflow expressed in standard cubic feet per minute (CFM) and in cubic meters per minute (m3/min).
2. Return air is through side opposite motor (left side).
3. Airflows above 1800 CFM (50.97 m3/min) require either return from two sides or one side plus bottom.
4. Motor voltage at 115 V.
5. NR = Operation at this static pressure is not recommended.
FILTER PERFORMANCE
The airflow capacity data published in Table 15 represents blower performance WITHOUT filters. To determine the approximate blower performance of the system, apply the filter drop value for the filter being
used or select an appropriate value from the Table 16.
NOTE: The filter pressure drop values in Table 16 are typical values for
the type of filter listed and should only be used as a guideline.
Actual pressure drop ratings for each filter type vary between filter manufacturers.
TABLE 16: Filter Performance - Pressure Drop Inches W.C. and (kPa)
AIRFLOW
RANGE
1 Opening
Sq. in.
0 - 750
751 - 1000
1001 - 1250
1251 - 1500
1501 - 1750
1751 - 2000
2001 & Above
FILTER TYPE
MINIMUM OPENING SIZE
230
330
330
330
380
380
463
m2
.15
.21
.21
.21
.25
.25
.30
2 Openings
Sq. in.
658
658
658
DISPOSABLE
1 Opening
m2
In w.c.
Pa
.42
.42
.42
0.01
0.04
0.08
0.08
0.14
0.17
0.17
2.5
10
20
20
35
42
42
WASHABLE FIBER*
2 Opening
In w.c.
0.08
0.09
0.09
1 Opening
Pa
In w.c.
Pa
20
22
22
0.01
0.03
0.07
0.07
0.13
0.15
0.15
2.5
7.5
17
17
32
37
37
PLEATED
2 Opening
In w.c.
0.06
0.07
0.07
1 Opening
2 Opening
Pa
In w.c.
Pa
In w.c.
Pa
15
17
17
0.15
0.20
0.20
0.25
0.30
0.30
0.30
37
50
50
62
75
75
75
0.17
0.17
0.17
42
42
42
* Hogs Hair Filters are the type supplied with furnace (if supplied).
Unitary Products Group
21
035-20417-001 Rev. C (0904)
APPLYING FILTER PRESSURE DROP TO
DETERMINE SYSTEM AIRFLOW
To determine the approximate airflow of the unit with a filter in place, follow the steps below:
1.
Select the filter type.
2.
Select the number of return air openings or calculate the return
opening size in square inches to determine the proper filter pressure drop.
3.
Determine the External System Static Pressure (ESP) without the
filter.
4.
Select a filter pressure drop from the table based upon the number
of return air openings or return air opening size and add to the
ESP from Step 3 to determine the total system static.
5.
If total system static matches a ESP value in the airflow table (i.e.
0.20 w.c. (50 Pa), 0.60 w.c. (150 Pa), etc,) the system airflow corresponds to the intersection of the ESP column and Model/Blower
Speed row.
6.
If the total system static falls between ESP values in the table (i.e.
0.58 w.c. (144 Pa), 0.75 w.c. (187 Pa), etc.), the static pressure
may be rounded to the nearest value in the table determining the
airflow using Step 5 or calculate the airflow by using the following
example.
MODEL NO.
1NP0580
1SR0302
1CT0302
1CT0303
1HT0901
1PS0501
1PS0502
1PS0503
1PS0504
1PS0505
1PS0506
1BR0317
1BR0321
1BR0324
1NK0301
22
Example: For a 120,000 BTUH (38.06 kW) furnace with 2 return openings and operating on high-speed blower, it is found that total system
static is 0.58” w.c. To determine the system airflow, complete the following steps:
Obtain the airflow values at 0.50 w.c. (125 Pa) & 0.60 w.c. (150 Pa)
ESP.
Airflow @ 0.50”: 2285 CFM (64.70 m3/min)
Airflow @ 0.60”: 2175 CFM (61.59 m3/min)
Subtract the airflow @ 0.50 w.c. (125 Pa) from the airflow @ 0.60 w.c.
(150 Pa) to obtain airflow difference.
2175 - 2285 = -110 CFM (3.11 m3/min)
Subtract the total system static from 0.50 w.c. (125 Pa) and divide this
difference by the difference in ESP values in the table, 0.60 w.c.
(150 Pa) - 0.50 w.c. (125 Pa), to obtain a percentage.
(0.58 - 0.50) / (0.60 - 0.50) = 0.8
Multiply percentage by airflow difference to obtain airflow reduction.
(0.8) X (-110) = -88
Subtract airflow reduction value to airflow @ 0.50 w.c. (125 Pa) to
obtain actual airflow @ 0.58 inwc (144 Pa) ESP.
2285 - 88 = 2197
FIELD INSTALLED ACCESSORIES - NON-ELECTRICAL
DESCRIPTION
USED WITH
PROPANE (LP) CONVERSION KIT
EXTERNAL SIDE FILTER RACK (6 PACK)
CONCENTRIC INTAKE/VENT 2”
CONCENTRIC INTAKE/VENT 3”
SIDEWALL VENT TERMINATION
ALL MODELS
ALL MODELS
40, 60, 80, 100 INPUT MBH
100, 120, 140 MBH
ALL MODELS
HIGH ALTITUDE PRESSURE SWITCH KIT
(Does Not Include Orifices)
FOR APPLICATION
INFORMATION SEE FORM
035-20506-001
EXTERNAL BOTTOM FILTER RACK
CONDENSATE NEUTRALIZER KIT
17-1/2” CABINETS
21” CABINETS
24-1/2” CABINETS
ALL MODELS
Unitary Products Group
035-20417-001 Rev. C (0904)
SECTION X: WIRING DIAGRAM
FIGURE 27: Wiring Diagram
Unitary Products Group
23
Subject to change without notice. Printed in U.S.A.
Copyright © by York International Corp. 2004. All rights reserved.
Unitary
Product
Group
035-20417-001 Rev. C (0904)
Supersedes: 035-20417-001 Rev. B (0904)
5005
York
Drive
Norman
OK
73069
Download PDF