BGS-1230

BGS-1230
WALL MOUNT FULL BACKGUARD (continued from page 2)
FIG.05
FIG.06
Front Section
Holes*
Back Section
Rack
Tabs*
BACKGUARD SYSTEM
#8
Self-tapping
sheet
metal
screws
Installation Guide
Models:
■
■
■
■
■
■
*Insure tabs and holes engage to secure top of backguard.
As product improvement is an
ongoing process at DCS, we
reserve the right to change
specifications or design without
notice.
5800 Skylab Road, Huntington Beach, CA 92647
Tel: (714) 372-7000 Fax: (714) 372-7001
www.dcsappliances.com
Customer Service: (888) 281-5698
Part No. 17443 Rev. C Litho in USA 06/2002
BGS-3030
BGS-1230
BGS-3036
BGS-1236
BGS-3048
BGS-1248
SPECIFICATIONS
WALL MOUNT FULL BACKGUARD INSTALLATION
Recommended Installation Order:
8 1/4 "
1) VENT HOOD
2) BACKGUARD SYSTEM
3) RANGE
8 15/16 "
1) Locate and level range per installation instructions.
MODEL
B
A
1 5/16 "
B
A
B
RACK
(13 5/8 ")
QTY.
RACK
(16 5/8 ")
QTY.
BGS-1230 29
7/8 "
10
1/8 "
-
-
BGS-3030 29
7/8 "
28
1/8 "
2
-
BGS-1236 35
7/8 "
10
1/8 "
-
-
BGS-3036 35
7/8 "
28
1/8 "
-
2
BGS-1248 47
7/8 "
10
1/8 "
-
-
BGS-3048 47
7/8 "
28
1/8 "
2
1
1 5/16 "
2) After unpacking all backguard system parts, locate the Back Section 1/8” (see fig. 03) above and
centered over the Island Trim attached to the range.* Secure Back Section to wall with the
appropriate fasteners (not supplied) to anchors or wood stud (fig. 03).
WARNING: The Back Section must be securely fastened to the wall. Failure to do so could cause
damage or personal injury if the Backguard was to pull free from wall when racks are
loaded. The maximum weight placed on the racks should be 10 lbs.
*After 1/8” is located, slots in back section may be used to adjust spacing between range island trim and
backguard for a flush fit.
3) Attach rod, end caps and center stanchion to Front Section of backguard with #10 machine screws
supplied (fig. 04).
4) Bend wedge-shaped tabs down on top of the front section approximately 3/16”. When mounting
the front section, insure that these tabs engage the mating holes in the top of the rear section (see
fig. 05).
A
5) Secure Front Section of backguard to Back Section with #8 self-tapping sheet metal screws supplied
(fig. 05).
WALL MOUNT LOW BACKGUARD INSTALLATION
6) Attach rack to rod (fig. 06). The maximum weight placed on the racks should be 10 lbs.
1) Locate and level range per installation instructions.
2) After unpacking all backguard system parts, locate the Back Section 1/8” above and centered over
the Island Trim attached to the range.* Secure Back Section to wall with the appropriate fasteners
(not supplied)(fig. 01).
FIG.03
FIG.04
Bend down approx. 3/16”
Back Section
Front Section
*After 1/8” is located, slots in back section may be used to adjust spacing between range island trim and
backguard for a flush fit.
3) Secure Front Section of backguard to Back Section with #8 self-tapping sheet metal screws supplied
(fig. 02).
FIG.01
Slots to choose desired spacing
between Range Island Trim and
Backguard.
FIG.02
End
Cap
Center
Stanchion
Slots to choose
desired spacing
between Range
Island Trim and
Backguard.
#10
Machine
Screws
Rod
Front Section
Back Section
Back Section
End
Cap
#8
Self-tapping
sheet metal
screws
Island
Trim
Island
Trim
(continued on back page)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement