Ryobi | HP61 | Operator`s manual | Ryobi HP61 Operator`s manual

1
3
5
7
9
OWNER’S OPERATOR'S MANUAL
CORDLESS DRILL-DRIVER
MODEL NO. HP61
THANK YOU FOR BUYING A RYOBI CORDLESS DRILL-DRIVER.
Your new cordless drill-driver has been engineered and manufactured to Ryobi’s high standard for dependability, ease of
operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
CAUTION: Carefully read through this entire operator’s manual before using your new cordless drill-driver.
Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your cordless drill-driver properly
and only for what it is intended, you will enjoy years of safe, reliable service.
Thank you again for buying Ryobi tools.
SAVE THIS MANUAL FOR FUTURE REFERENCE
TABLE OF CONTENTS
■ Table Of Contents/Typical Applications. .......................................................................................2
■ Rules For Safe Operation ........................................................................................................ 3-5
A. Precautions On Using Your Cordless Tool .............................................................................4
B. Important Safety Instructions For Charger ......................................................................... 4-5
C. Precautions Regarding The Use Of Charger And Batteries ...................................................5
■ Operation ................................................................................................................................6-11
A. Specifications .........................................................................................................................6
B. Know Your Drill-Driver, Charging Your Drill-Driver .................................................................6
C. Important Information For Recharging Hot Batteries, Switch, Switch Lock, Reversible ........ 7
D. Keyless Chuck, Installing Bits ................................................................................................8
E. Removing Bits, Screwdriving, Bit Storage, Level Drilling .......................................................9
F. Drilling ..................................................................................................................................10
G. Chuck Removal, To Retighten a Loose Chuck ..................................................................... 11
■ Maintenance ..............................................................................................................................12
■ Battery Removal ........................................................................................................................13
A. Disposal Of Exhausted Batteries
B. Battery Removal, Preparation For Recycling .......................................................................13
■ Service Information ....................................................................................................................14
CAUTION: Carefully read through this entire manual before using your new drill-driver.
10
22
1
3
TYPICAL APPLICATIONS
21
18
20
22
19
DRILLING
LEVEL DRILLING
Page 2
23
RULES FOR SAFE OPERATION
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident
prevention measures.
SYMBOL
MEANING
SAFETY ALERT SYMBOL:
Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others. Always
follow the safety precautions to reduce the risk of fire, electric shock, and personal injury.
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others. Always
follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to yourself
or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal
injury.
NOTE:
Advises you of information or instructions vital to the operation or maintenance of the equipment.
KNOW YOUR CORDLESS TOOL
READ ALL INSTRUCTIONS
Safe operation of this cordless tool requires that you read
and understand this Operator's Manual and all labels affixed
to the tool. Learn its applications and limitations as well as
the potential hazards related to a cordless tool. Keep this
manual readily available for future reference.
IMPORTANT
Servicing of a tool requires extreme care and knowledge of
the system and should be performed only by a qualified
service technician. For service we suggest you return the
tool to your nearest Authorized Service Center for repair.
When servicing, use only identical replacement parts.
WARNING:
Do not attempt to operate this tool until you have read
thoroughly and understand completely all instructions,
safety rules, etc. contained in this manual. Failure to
comply can result in accidents involving fire, electric
shock, or serious personal injury. Save this operator's
manual and review it frequently for continuing safe
operation, and instructing others who may use this tool.
WARNING:
When using power tools, basic safety precautions should
always be followed to reduce the risk of fire, electric shock,
and personal injury, including the following precautions.
1. KEEP THE WORK AREA CLEAN. Cluttered work
areas and work benches invite injuries.
2. CONSIDER WORK AREA ENVIRONMENT. Keep
work area well lit. Do not use tool in presence of
flammable liquids or gases.
3. GUARD AGAINST ELECTRICAL SHOCK BY
PEVENTING BODY CONTACT WITH
GROUNDED SURFACES. For example: Pipes,
radiators, ranges, refrigerator enclosures.
4. KEEP CHILDREN AND VISITORS AWAY. All
visitors should wear safety glasses and be kept a
safe distance from work area. Do not let visitors
contact tool or extension cord.
5. STORE IDLE TOOLS. When not in use tools
should be stored in a dry and high or locked-up
place - out of the reach of children.
6. DON'T FORCE TOOL. It will do the job better and
safer at the rate for which it was designed.
7. USE RIGHT TOOL. Don't force small tool or
attachment to do the job of a heavy duty tool. Don't
use tool for purpose not intended - for example - A
circular saw should never be used for cutting tree
limbs or logs.
8. WEAR PROPER APPAREL. Do not wear loose
clothing or jewelry that can get caught in tool's
moving parts and cause personal injury. Rubber
gloves and nonskid footwear are recommended
Page 3
RULES FOR SAFE OPERATION (Continued)
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
when working outdoors. Wear protective hair
covering to contain long hair and keep it from being
drawn into nearby air vents.
ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistant lenses; they
are NOT safety glasses.
PROTECT YOUR LUNGS. Wear a face mask or
dust mask if operation is dusty.
PROTECT YOUR HEARING. Wear hearing
protection during extended periods of operation.
SECURE WORK. Use clamps or a vise to hold
work. It's safer than using your hand and it frees
both hands to operate tool.
DON'T OVERREACH. Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
at all times, and clean for best and safest
performance. Follow instructions for lubricating
and changing accessories.
REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
AVOID UNINTENTIONAL STARTING. Do not
carry the tool with your finger on the switch. Be
sure switch is off when not in use.
STAY ALERT. Watch what you are doing and use
common sense. Do not operate tool when you are
tired. Do not rush.
CHECK DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged
should be carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
properly repaired or replaced by an authorized
service center unless indicated elsewhere in this
instruction manual.
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an Authorized Service Center.
DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol, or any medication.
INSPECT FOR and remove all nails from lumber
before drilling.
DO NOT CHARGE BATTERY TOOL IN A DAMP
OR WET LOCATION.
PRECAUTIONS ON USING YOUR
CORDLESS TOOL
This product contains Nickel-Cadmium batteries which
must be disposed of properly.
1.
2.
3.
4.
5.
Be aware that this tool is always in an operating
condition, because it does not have to be plugged
into an electrical outlet.
First, charge the batteries.
When not in use, lock the switch.
When operating at a high place, be aware of things
below you.
Before drilling into walls, ceilings, or floors, make
sure that there are no concealed power cables
inside.
WARNING:
Drilling into electrical wiring can cause drill bit
and chuck to become electically live. Do not
touch the chuck or metal housing when drilling
into a wall; grasp only the insulated handle(s)
provided on the tool.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER
1. SAVE THESE INSTRUCTIONS. This manual
contains important safety and operating instructions
for battery charger part number 4400001.
2. Before using battery charger, read all instructions
and cautionary markings in the manual, on battery
charger, and product using battery charger.
WARNING:
To reduce risk of injury, charge only nickelcadmium type rechargeable batteries. Other
types of batteries may burst causing personal
injury and damage.
3. Do not expose charger to rain or snow.
4. Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a
risk of fire, electric shock, or injury to persons.
5. To reduce risk of damage to electric plug and cord,
pull by the plug rather than the cord when
disconnecting charger.
6. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
Page 4
RULES FOR SAFE OPERATION (Continued)
7. An extension cord should not be used unless
absolutely necessary. Use of improper extension
cord could result in a risk of fire and electric shock.
If extension cord must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of plug
on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet) 25 ft. 50 ft. 100 ft.
Cord Size (AWG)
16
16
16
Note: AWG = American Wire Gage
8. Do not operate charger with a damaged cord or
plug. Replace immediately.
9. Do not operate charger if it has received a sharp
blow, been dropped, or otherwise damaged in any
way; take it to an AUTHORIZED SERVICE
CENTER.
10. Do not disassemble charger; take it to an
AUTHORIZED SERVICE CENTER when service
or repair is required. Incorrect reassembly may
result in a risk of electric shock or fire.
11. To reduce risk of electric shock, unplug charger from
outlet before attempting any maintenance or cleaning.
Turning off controls will not reduce this risk.
4.
5.
6.
7.
8.
PRECAUTIONS REGARDING THE USE OF
CHARGER AND BATTERIES
1.
2.
3.
Do not charge batteries when temperature is below
50° F (10° C) or above 95° F (35° C).
The charger is designed to operate on standard
household electrical power. Do not attempt to use
it on any other voltage.
Consecutive charging may cause overheating. If
you need to recharge batteries consecutively, wait
for about 15 minutes to allow charger to cool.
Do not charge by means of an engine generator or
DC power source.
Do not store the tool in locations where the
temperature may reach or exceed 104° F (40° C),
such as outside sheds or metal buildings in summer.
Do not incinerate the tool, even if it is severely
damaged or completely worn out. The batteries
may explode in fire.
Battery leakage may occur under conditions of
extreme usage or temperature. If liquid comes in
contact with skin, wash quickly with soap and
water, then with lemon juice or vinegar. If liquid
gets in your eyes, wash for at least 10 minutes and
seek medical attention immediately.
Do not short-circuit the battery.
WARNING:
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some
examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and
other masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
SAVE THESE INSTRUCTIONS
Look for this symbol to point out important safety precautions.
It means attention!!! Your safety is involved.
Page 5
OPERATION
SPECIFICATIONS:
Switch
Two-Speed
No Load Speed
300/500 RPM
Clutch
24 Positions
Charger Input
120V, 60 Hz, AC only
Charge Rate
3-6 Hours
7
DC Motor 6.0V
BIT
STORAGE
AREA
5
Motor
1
3
3/8 in. Keyless
LEVEL
9
Chuck
TORQUE
ADJUSTMENT
RING
SWITCH
TRIGGER
KNOW YOUR DRILL-DRIVER
DIRECTION OF
ROTATION
SELECTOR
KEYLESS
CHUCK
See Figure 1.
Before attempting to use any tool, familiarize yourself with all
operating features and safety requirements.
Fig. 1
WARNING:
BATTERY
CHARGER
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is
sufficient to inflict severe injury.
CHARGE
INDICATOR
LIGHT (LED)
CHARGING YOUR DRILL-DRIVER
This tool has been shipped in a low charge condition to
prevent possible problems. Therefore, you should charge it
at least 6 hours prior to use.
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by recharging) for them to become fully charged.
INPUT
JACK
TO CHARGE
■
■
■
■
■
Charge only with the charger provided.
Connect charger to the tool by inserting charger plug
into input jack. Note: As shown in figure 2, input jack is
located at rear of tool.
Make sure power supply is normal house voltage,
120 volts, 60 Hz, AC only.
Connect charger to power supply.
The charge indicator light (LED) indicator, which is
located on rear of drill, will light up when charger is
properly connected to power supply. This red light indicates your drill is charging and will remain on until
charger is disconnected from power supply.
CHARGER
PLUG
■
■
■
■
Fig. 2
After normal usage, 3 hours of charging time is required to be fully charged. A minimum charge time of 6
hours is required to recharge a completely discharged
battery.
The charger housing and the tool handle will become
slightly warm to the touch while charging. This is normal and does not indicate a problem.
DO NOT operate drill while it is connected to the charger.
The driving ability will not increase.
DO NOT place charger in an area of extreme heat or
cold. It works best at normal room temperature.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your
eyes, which can result in severe eye damage. Before beginning power tool operation,
always wear safety goggles or safety glasses with side shields and a full face shield
when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or
standard safety glasses with side shields.
Page 6
OPERATION
IMPORTANT INFORMATION FOR
RECHARGING HOT BATTERIES
REVERSE
DIRECTION
OF ROTATION
SELECTOR
1
3
5
7
When using your drill-driver continuously, the batteries become hot. You should let the batteries cool down for approximately 30 minutes before attempting to recharge.
Note: This situation occurs when continuous use of your
drill-driver causes the batteries to become hot. It does not
occur under normal circumstances. Refer to "Charging
Your Drill-Driver" for normal recharging of batteries. If the
charger does not charge your batteries under normal circumstances, return both the drill-driver and charger to your
nearest AUTHORIZED SERVICE CENTER for electrical
check.
For more information on the battery recycling call
1-800-8 BATTERY.
CENTER
POSITION (LOCK)
SWITCH
TRIGGER
FORWARD
CAUTION:
Fig. 3
Your drill contains special high temperature batteries to
help prevent battery damage when left on charge for
extended periods of time. However, once the batteries
become fully charged, we recommend that you unplug
your charger from power supply and disconnect it from
drill.
REVERSIBLE
See Figure 3.
This tool is reversible. The direction of rotation is controlled
by a selector located above the switch trigger. With the drill
held in normal operating position, the direction of rotation
selector should be positioned to the left of the switch for
drilling. The drilling direction is reversed when the selector is
to the right of the switch. When the selector is in center
position, the switch trigger is locked.
WARNING:
If any parts are missing, do not operate tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.
CAUTION:
To prevent gear damage, always allow chuck to come to
a complete stop before changing the direction of rotation.
SWITCH
See Figure 3.
Your drill starts and stops by depressing and releasing the
switch trigger.
Your drill has a two-speed feature in the switch. Depress
the switch trigger halfway for driving screws at low speed.
Depress the switch trigger all the way for normal drilling.
Release the switch trigger to turn drill OFF.
SWITCH LOCK
See Figure 3.
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
when not in use. To lock the switch trigger, place the direction
of rotation selector in the center position.
To stop, release switch trigger and allow the chuck to come
to a complete stop.
WARNING:
Battery tools are always in operating condition. Therefore,
switch should always be locked when not in use or when
carrying at your side.
Page 7
OPERATION
KEYLESS CHUCK
RELEASE
(UNLOCK)
See Figure 4.
A keyless chuck has been provided with your drill to allow for
easy installation and removal of bits. As the name implies,
you can hand tighten or release drill bits in the chuck jaws.
Grasp and hold the collar of the chuck with one hand. Rotate
the chuck body with your other hand. The arrows on the
chuck indicate which direction to rotate the chuck body in
order to GRIP (tighten) or RELEASE (unlock) the drill bit.
1
3
5
7
9
CHUCK BODY
WARNING:
Do not hold the chuck body with one hand and use the
power of the drill to tighten chuck jaws on drill bit. Chuck
body could slip in your hand or your hand could slip and
come in contact with rotating drill bit. This could cause
an accident resulting in serious personal injury.
GRIP
(TIGHTEN)
CHUCK
COLLAR
Fig. 4
CHUCK JAWS
CHUCK BODY
■
■
Insert your drill bit into the chuck the full length of the
jaws. See Figure 5.
Tighten the chuck jaws on the drill bit. To tighten, grasp
and hold the collar of the chuck with one hand, while
rotating the chuck body with your other hand.
DRILL BIT
3
■
Place the direction of rotation selector in center position.
This will turn off the power to your drill.
Open or close the chuck jaws to a point where the
opening is slightly larger than the bit size you intend to
use. Also, raise the front of your drill slightly to keep the
bit from falling out of the chuck jaws.
1
■
5
7
9
INSTALLING BITS
CHUCK COLLAR
RIGHT
3
5
7
9
Note: Rotate the chuck body in the direction of the arrow
marked GRIP to tighten the chuck jaws. DO NOT use a
wrench to tighten or loosen the chuck jaws.
Fig. 5
1
WARNING:
Do not insert drill bit into chuck jaws and tighten as shown
in figure 6. This could cause drill bit to be thrown from
drill resulting in possible serious personal injury or
damage to the chuck.
WRONG
Fig. 6
Page 8
OPERATION
REMOVING BITS
SCREWDRIVING
9
TO DECREASE
TORQUE
3
5
7
TORQUE
ADJUSTMENT
RING
1
See Figure 5.
■ Place the direction of rotation selector in center position.
This will turn off the power to your drill.
■ Loosen the chuck jaws from drill bit.
■ To loosen: grasp and hold the collar of the chuck with
one hand, while rotating chuck body with your other hand.
Note: Rotate chuck body in the direction of the arrow
marked RELEASE to loosen chuck jaws. DO NOT use
a wrench to tighten or loosen the chuck jaws.
■ Remove drill bit from chuck jaws.
TO INCREASE
TORQUE
TORQUE ADJUSTMENT
(Driving power of your drill-driver)
When using your drill-driver for various driving aplications, it
becomes necessary to increase or decrease the torque in
order to help prevent the possibility of damaging screw
heads, threads, workpiece, etc. In general, torque should
correspond to the intensity of the screw diameter. If the
torque is too high or the screws too small, the screws may be
damaged or broken.
The torque is adjusted by rotating the torque adjustment ring.
See Figure 7. The torque is greater when the torque adjustment ring is set on a higher setting. The torque is less when
the torque adjustment ring is set on a lower setting.
Fig. 7
3
5
7
9
SCREWDRIVER BITS
1
BIT
STORAGE
AREA
Fig. 8
The proper setting depends on the type of material and the
size of screw you are using.
TO ADJUST TORQUE
For driving screws in hard wood.
For driving large screws.
For heavy drilling.
3
1
22
10
22
• 13 - 16
• 17 - 20
• 21 - 24
LEVEL
20
■
Identify the twenty four torque indicator settings located
on the front of your drill. See Figure 7.
Rotate adjustment ring to the desired setting.
• 1-4
For driving small screws.
• 5-8
For driving screws into soft material.
• 9 - 12 For driving screws into soft and hard
materials.
18
■
BIT STORAGE
See Figure 8.
When not in use, bits provided with your drill can be placed
in the storage area located on the top of your drill as shown
in figure 8.
LEVEL DRILLING
See Figure 9.
A convenient new feature provided with your drill is a level.
It is recessed in the motor housing on top of your drill. It can
be used to keep drill bit level during drilling operations.
Page 9
Fig. 9
OPERATION
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating tool. Failure to do so could result
in objects being thrown into your eyes, resulting in
possible serious injury.
DRILLING
21
23
WARNING:
19
See Figure 10.
When drilling hard, smooth surfaces, use a center punch to
mark the desired hole location. This will prevent the drill bit
from slipping off center as the hole is started. However, the
lower speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate your
drill at lower speed until the hole is started.
The material to be drilled should be secured in a vise or with
clamps to keep it from turning as the drill bit rotates.
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start tool.
Move the drill bit into the workpiece, applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
Fig. 10
Be prepared for binding or breakthrough. When these
situations occur, the drill has a tendency to grab and kick
in the opposite direction, and could cause loss of control
when breaking through material. If you are not prepared,
this loss of control can result in possible serious injury.
When drilling metals, use a light oil on the drill bit to keep it
from overheating. The oil will prolong the life of the bit and
increase the drilling action.
If the bit jams in workpiece or if the drill stalls, release switch
trigger immediately. Remove the bit from the workpiece and
determine the reason for jamming.
Page 10
OPERATION
CHUCK REMOVAL
MALLET
KEYLESS
CHUCK
9
CHUCK
JAWS
1
3
5
7
See Figures 11, 12, and 13.
The chuck must be removed in order to use some
accessories. To remove:
■ Lock the switch trigger by placing the direction of rotation
selector in center position.
■ Insert a 5/16 inch or larger hex key wrench into the chuck
of your drill and tighten the chuck jaws securely.
■ Tap the hex key wrench sharply with a mallet in a
clockwise direction. See Figure 11. This will loosen the
screw in the chuck for easy removal.
■ Open chuck jaws and remove hex key wrench. Remove
the chuck screw by turning it in a clockwise direction.
See Figure 12. Note: The screw has left hand threads.
■ Insert hex key wrench in chuck and tighten chuck jaws
securely. Tap sharply with a mallet in a counterclockwise
direction. This will loosen chuck on the spindle. It can
now be unscrewed by hand. See Figure 13.
Fig. 11
HEX KEY WRENCH
7
9
TO RETIGHTEN A LOOSE CHUCK
3
1
Fig. 12
3
5
1
■
■
9
■
Lock the switch trigger by placing the direction of rotation
selector in center position.
Insert hex key wrench into chuck and tighten chuck jaws
securely. Tap hex key wrench sharply with a mallet in a
clockwise direction. This will tighten chuck on the spindle.
Open the chuck jaws and remove hex key wrench.
Tighten the chuck screw. Note: The chuck screw has
left hand threads.
7
■
5
The chuck may become loose on spindle and develop a
wobble. Also, the chuck screw may become loose causing
the chuck jaws to bind and prevent them from closing. To
tighten, follow these steps:
Fig. 13
Page 11
MAINTENANCE
BATTERIES
Your drill is equipped with Nickel-Cadmium rechargeable batteries. Length of service from each charging will depend on the
type of work you are doing.
The batteries in this tool have been designed to provide maximum trouble-free life. However, like all batteries, they will
eventually wear out. Do not disassemble your drill and attempt to replace the batteries. Handling of these batteries,
especially when wearing rings and jewelry, could result in a serious burn.
To obtain the longest possible battery life, we suggest the following:
■
■
■
Store and charge your batteries in a cool area. Temperatures above normal room temperature will shorten battery life.
Never store batteries in a discharged condition. Wait for the batteries to cool and charge immediately.
All batteries gradually lose their charge. The higher the temperature, the quicker they lose their charge. If you store your
tool for long periods of time without using it, recharge the batteries every month or two. This practice will prolong battery
life.
CAUTION:
Your drill-driver contains special high temperature batteries to help prevent battery damage when left on charge for
extended periods of time. However, once the batteries become fully charged, we recommend that you unplug the charger
from power supply and remove it from drill-driver.
DO NOT ABUSE POWER TOOLS. Abusive practices can
damage the tool, as well as the work piece.
WARNING:
When servicing use only identical replacement parts. Use
of any other parts may create a hazard or cause product
damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
a clean cloth to remove dirt, oil, grease, etc.
WARNING:
Do not attempt to modify this tool or create accessories
not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
WARNING:
CAUTION:
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact
with plastic parts. They contain chemicals that can
damage, weaken, or destroy plastics.
Any repairs requiring disassembly should only be
performed by an AUTHORIZED SERVICE CENTER. For
the repair center nearest you, call 1-800-525-2579.
Page 12
BATTERY REMOVAL
DISPOSAL OF EXHAUSTED BATTERIES
C YC
R ER B R CL E
To preserve natural resources, please
recycle or dispose of batteries properly.
DRILL
HANDLE
37
1.8
This product contains nickel-cadmium
battery. Local, state, or federal laws may
N i Cd
prohibit disposal of Nickel-Cadmium
00
.822.88
batteries in ordinary trash.
Consult your local waste authority for information regarding
available recycling and/or disposal options.
For more information on battery recycling call 1-800-8
BATTERY.
WARNING:
Do not attempt to disassemble batteries. Fire or injury
may result.
TO
REMOVE COVER
BATTERY
COVER
BATTERY REMOVAL, PREPARATION FOR
RECYCLING
Fig. 14
See Figures 14 and 15.
TO REMOVE:
■ Lock switch trigger by placing the forward/reverse switch
in center position.
■ Remove battery cover from bottom of drill handle by
depressing and pushing cover in the direction of the arrow
as shown in figure 14.
■ Slide battery assembly from drill handle enough to
expose leads and battery terminals. See Figure 15.
Disconnect leads from battery terminals.
Note: Be careful not to break battery terminals when
disconnecting leads.
DRILL
HANDLE
BATTERY
LEAD
WARNING:
Upon removal, cover the battery assemblies terminals
with heavy duty adhesive tape. Do not attempt to destroy
or disassemble battery assembly or remove any of its
components. Also, never touch both terminals with metal
objects and/or body parts, as short circuit may result.
Keep away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
BATTERY
LEAD
BATTERIES
Page 13
Fig. 15
OWNER'S OPERATOR'S MANUAL
CORDLESS DRILL-DRIVER
MODEL NO. HP61
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or service,
simply contact your nearest Authorized Service Center. Be sure to provide all pertinent facts
when you call or visit. Please refer to the Service Center insert or call 1-800-525-2579 in
the United States or 1-800-265-6778 in Canada for your nearest Authorized Service Center.
You can also check our web site at www.ryobi.com for a complete list of Authorized Service
Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS,
ALWAYS GIVE THE FOLLOWING INFORMATION:
•
MODEL NUMBER
•
SERIAL NUMBER
HP61
RYOBI AMERICA CORP.
1424 Pearman Dairy Road
Anderson, SC 29625
Post Office Box 1207
Anderson, SC 29622-1207
Phone 1-800-525-2579
1980061
8-00
RYOBI CANADA INC.
Post Office Box 910
Cambridge, Ontario N1R 6K2
Phone 1-800-265-6778
Download PDF