Raynor | 3800RGD | Owner`s manual | Raynor 3800RGD Owner`s manual

Raynor Garage Doors
1101 E. River Rd.
Dixon, Illinois 61021
www.raynor.com
TM
ible with
ER
W
O
YP
B
D
N
STA
Se
De
tails
Install On Sectional Doors With
Torsion Assemblies Only
t
pa
Co
For Residential and Light Duty Commercial Use
m
GARAGE DOOR OPENER
Model 3800RGD
r
eP
fo
3
age 1
Owner’s Manual
■
Please read this manual and the enclosed safety materials carefully!
■
Fasten the manual near the garage door after installation.
■
The door WILL NOT CLOSE unless The Protector System® and cable tension monitor are
connected and properly aligned.
■
Periodic checks of the opener are required to ensure safe operation.
■
The model number label is located behind the hinged door of your opener.
■
Do NOT exceed 10 complete cycles of door operation per hour.
TABLE OF CONTENTS
Introduction
2-5
Operation
Safety symbol review and signal word review . . . . . . . .2
Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Preparing your garage door . . . . . . . . . . . . . . . . . . . . . .4
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Carton inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Hardware inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Assembly
6
Attach the collar to the motor unit . . . . . . . . . . . . . . . . . .6
Attach mounting bracket to the motor unit . . . . . . . . . . .6
Installation
Programming
7-16
28-30
To add or reprogram a hand-held remote control . . . . .28
To erase all codes from motor unit memory . . . . . . . . .28
3-Button remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
To add, reprogram or change
a keyless entry PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Programming work light or additional work light . . . . . .30
Installation safety instructions . . . . . . . . . . . . . . . . . . . . .7
Position the opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Attach the emergency release rope and handle . . . . . . .8
Install the power door lock . . . . . . . . . . . . . . . . . . . . . . .8
Attach the cable tension monitor (Required) . . . . . . . . . .9
Install the door control . . . . . . . . . . . . . . . . . . . . . . . . . .10
Install remote light . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Electrical requirements . . . . . . . . . . . . . . . . . . . . . . . . .12
Mount the Standby Power Unit (SPU) (not provided) . .13
Install The Protector System® . . . . . . . . . . . . . . . . . .14-16
Adjustment
21-27
Operation safety instructions . . . . . . . . . . . . . . . . . . . . .21
Using your garage door opener . . . . . . . . . . . . . . . . . .21
Using the wall-mounted door control . . . . . . . . . . . . . .22
Using the remote control . . . . . . . . . . . . . . . . . . . . . . . .23
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
The remote control battery . . . . . . . . . . . . . . . . . . . . . .23
Care of your opener . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Having a problem? (Troubleshooting) . . . . . . . . . . .24-25
Smart Control Panel™ messages . . . . . . . . . . . . . . . . .26
Diagnostic Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Repair Parts
31-32
Installation parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Motor unit assembly parts . . . . . . . . . . . . . . . . . . . . . . .32
Accessories
Operator Notes
Repair Parts and Service
Warranty
17-20
Program the travel limits . . . . . . . . . . . . . . . . . . . . . . . .17
Setting the force . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Test the safety reversal system . . . . . . . . . . . . . . . . . . .19
Test The Protector System® . . . . . . . . . . . . . . . . . . . . . .19
Test cable tension monitor . . . . . . . . . . . . . . . . . . . . . .20
Test power door lock . . . . . . . . . . . . . . . . . . . . . . . . . . .20
To open door manually . . . . . . . . . . . . . . . . . . . . . . . . .20
33
34-35
36
36
INTRODUCTION
Safety Symbol Review
and Signal Word Review
This garage door opener has been designed and tested to offer safe service provided it is installed, operated,
maintained and tested in strict accordance with the instructions and warnings contained in this manual.
When you see these Safety Symbols and Signal Words on
the following pages, they will alert you to the possibility of
serious injury or death if you do not comply with the
warnings that accompany them. The hazard may come
from something mechanical or from electric shock. Read
the warnings carefully.
Mechanical
Electrical
When you see this Signal Word on the following pages, it
will alert you to the possibility of damage to your garage
door and/or the garage door opener if you do not comply
with the cautionary statements that accompany it. Read
them carefully.
2
Planning
Survey your garage area to see if any of the conditions
below apply to your installation. Additional materials may
be required. You may find it helpful to refer back to this
page as you proceed with the installation of your opener.
Depending on your requirements, there are several
installation steps which may call for materials or hardware
not included in the carton.
This opener is compatible with:
• Doors that use a torsion bar, springs and a door no
more than 14' (4.2 m) high.
• 4"-6" (10 cm - 15 cm) drums, not to be used on tapered
drums over 6" (15 cm).
• High lift and standard lift sectional doors up to 14'
(4.2 m) high.
• Doors up to 18' (5.4 m) wide.
• Doors up to 180 sq. ft. (16.7 sq. m).
• 1" (2.5 cm) torsion bar only.
• Review or inspect proposed installation area. Opener
can be installed on left or right side of door. Select the
side that meets the requirements listed below.
- Must have minimum of 2-1/2" (6.4 cm) between the
garage wall and the center of the torsion bar.
- Must have minimum of 3" (7.6 cm) between the ceiling
and the center of torsion bar.
- Must have minimum of 8" (20.3 cm) between the side
garage wall (or obstruction) and the end of torsion bar.
• The torsion bar must extend at least 1" to 5"
(2.5 cm to 12 cm) past the bearing plate.
• An electric outlet is required within 6' (1.8 m) of the
installation area. If outlet does not exist, contact a
qualified electrician.
• Depending upon garage construction, extension
brackets or wood blocks may be needed to install safety
reversing sensors.
• Alternate floor mounting of the safety reversing sensors
will require hardware not provided.
• A model 475RGD EverChargeTM Standby Power Unit is
strongly recommended if there is no access door to the
garage, as this opener cannot be used in conjunction
with an external emergency release mechanism.
• Any gap between the floor and the bottom of the door
must not exceed 1/4" (6 mm). Otherwise the safety
reversal system may not work properly.
NOTE: Inspect the torsion bar while the door is raised and
lowered. It is important that there is no noticeable
movement up and down or left and right. If this type of
movement is not corrected, life of this opener will be
greatly reduced.
Cable Tension
Monitor
Remote Light
Motor unit
Torsion Spring
Drum
Wall-mounted
Access Door Door Control
Power
Door Lock
Safety
Reversing
Sensor
Safety
Reversing Sensor
Gap between floor
and bottom of door must not exceed 1/4" (6 mm).
3
Preparing your Garage Door
Before you begin:
• Disable locks.
• Remove any ropes connected to garage door.
• Complete the following test to make sure your garage
door is balanced and is not sticking or binding:
1. Lift the door about halfway as shown. Release the
door. If balanced, it should stay in place, supported
entirely by its springs.
2. Raise and lower the door to see if there is any
binding or sticking.
If your door binds, sticks or is out of balance, call a
trained door systems technician.
3. Verify equal cable tension on each side of door.
Cable tension should remain equal during the entire
travel of the door.
To prevent possible SERIOUS INJURY or DEATH:
• ALWAYS call a trained door systems technician if garage
door binds, sticks or is out of balance. An unbalanced garage
door may not reverse when required.
• NEVER try to loosen, move or adjust garage door, door
springs, cables, pulleys, brackets or their hardware, ALL of
which are under EXTREME tension.
• Disable ALL locks and remove ALL ropes connected to
garage door BEFORE installing and operating garage door
opener to avoid entanglement.
To prevent damage to garage door and opener:
• ALWAYS disable locks BEFORE installing and operating the
opener.
• ONLY operate garage door opener at 120V, 60 Hz to avoid
malfunction and damage.
• Do NOT exceed 10 complete cycles of door operation per
hour.
Specifications
Volts . . . . . . . . . . . . . . . . . . .120 Vac - 60 Hz, ONLY
Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.0 AMP
Rated Load . . . . . . . . . . . . . . . . .325 in.lb/sec
10 Cycles per Hour
Sectional Door
Tools needed
During assembly, installation and adjustment of the
opener, instructions will call for hand tools as illustrated
below.
1
Drill
2
Pliers
Wire Cutters
Tape Measure
3/16" and 1/8"
Hex Key Wrench
5/32", 3/16", 5/16"
and 3/4" Drill Bits
Stepladder
Pencil
1/4", 5/16" & 3/8" Sockets
and Wrench with 6" Extension
Claw Hammer
Screwdriver
Adjustable End Wrench
Torque Meter (not shown)
4
Needle Nose Pliers
Carton Inventory
purchased. If anything is missing, carefully check the
packing material.
Your garage door opener is packaged in one carton which
contains the motor unit and the parts illustrated below.
Note that accessories will depend on the model
Remote Control
Visor Clip
LOC
K
LIG
H
T
SECURITY✚®
3-Button Remote Control (1)
Model 373PG (1)
Remote Light (Opener Light)
with Hardware Bag
Smart Control Panel™
2-Conductor Bell Wire
White & White/Red
Power Door Lock
2-Conductor White &
White/Black Bell Wire
with Connector
Collar with Screws
Motor Unit
Mounting Bracket
The Protector System®
(2) Safety Reversing Sensors
(1 Sending Eye and 1 Receiving Eye)
with 2-Conductor White & White/Black
Bell Wire attached
Cable Tension
Monitor with 2-Conductor
Green/White Bell Wires
Safety Labels
and
Literature
Safety Sensor
Bracket (2)
Hardware Inventory
Self Tapping Screw #10-32 (2)
Drywall Anchor (2)
Drywall Anchor (Screw-In) (2)
Handle
Rope
Insulated Staples (30)
Lock Template
INSTALLATION HARDWARE
Hex Screw #14-10x1-7/8" (4)
Screw #6x-1-1/4" (2)
Machine Screw #6x1" (2)
Carriage Bolt 1/4"-20x1/2" (2)
Wing Nut 1/4"-20 (2)
Pan Head Screw 1/4"-20x1/2" (2)
Hex Head Screw #8x1" (2)
5
ASSEMBLY STEP 1
Attach the Collar to the Motor Unit
To prevent possible SERIOUS INJURY or DEATH, the collar
MUST be properly tightened. The door may not reverse
correctly or limits may be lost due to collar slip.
To avoid installation difficulties, do not run the garage
door opener until instructed to do so.
• Loosen the collar screws.
• Attach collar to either the left or the right side of the
motor unit. Ensure that the collar is seated all the way
on motor shaft until stop is reached (Figure 1).
• Position the collar so that the screws are facing up
(accessible when attached to the torsion bar).
• Tighten both sides of collar screws equally to secure
collar to the motor unit (12-14 ft./lbs. of torque)
(Figure 2).
NOTE: For most installations the screws should be facing
up for easy access. Do not tighten set screws until
indicated.
Collar Screw
Figure 1
Set Screw
Collar Screw
Figure 2
ASSEMBLY STEP 2
Attach Mounting Bracket to Motor Unit
• Loosely attach slotted side of mounting bracket to the
same side of the motor unit as the collar, using
self-threading screws provided.
NOTE: Do not tighten until instructed. Illustrations shown
are for left side installation.
RIGHT
WRONG
HARDWARE SHOWN ACTUAL SIZE
Screw
#10-32
Socket Wrench
6
WARNING
INSTALLATION
IMPORTANT INSTALLATION INSTRUCTIONS
WARNING
To reduce the risk of SEVERE INJURY or DEATH:
1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND
INSTRUCTIONS.
2. Install garage door opener ONLY on properly balanced and
lubricated garage door. An improperly balanced door may
not reverse when required and could result in SEVERE
INJURY or DEATH.
3. ALL repairs to cables, spring assemblies and other hardware
MUST be made by a trained door systems technician
BEFORE installing opener.
4. Disable ALL locks and remove ALL ropes connected to
garage door BEFORE installing opener to avoid
entanglement.
5 Mount emergency release handle no higher than 6 feet
(1.83 m) above floor.
6. NEVER connect garage door opener to power source until
instructed to do so.
7. NEVER wear watches, rings or loose clothing while installing
or servicing opener. They could be caught in garage door or
opener mechanisms.
8. Install wall-mounted garage door control:
• within sight of the garage door.
• out of reach of children at minimum height of 5 feet
(1.5 m).
• away from ALL moving parts of the door.
9. Place entrapment warning label on wall next to garage door
control.
10. Place manual release/safety reverse test label in plain view
on inside of garage door.
11. Upon completion of installation, test safety reversal system.
Door MUST reverse on contact with a 1-1/2" (3.8 cm) high
object (or a 2x4 laid flat) on the floor.
INSTALLATION STEP 1
Position the Opener
To prevent possible SERIOUS INJURY or DEATH:
• Concrete anchors MUST be used if mounting bracket into
masonry.
• NEVER try to loosen, move or adjust garage door, springs,
cables, pulleys, brackets or their hardware, ALL of which are
under EXTREME tension.
• ALWAYS call a trained door systems technician if garage
door binds, sticks or is out of balance. An unbalanced
garage door might not reverse when required.
• Operator MUST be mounted at a right angle to the torsion
bar to avoid premature wear on the collar.
NOTE: For additional mounting options see accessories
page.
1. Close the garage door completely.
2. Slide the opener with collar over the end of the torsion
bar. Ensure that the collar does not touch the bearing
plate. Check to make sure the mounting bracket is
located on a solid surface such as wood, concrete or
door/flag bracket. Snug collar screws to help assure
proper alignment of operator. Mark the bracket holes. It
may be necessary to cut the torsion bar if it is too long
or damaged.
3. Loosen collar screws from torsion bar and remove the
opener. Drill 3/16" pilot holes at the marked locations.
Drill through steel plate if needed.
4. Reinstall the opener by sliding the collar over the torsion
bar until pilot holes align with bracket. Securely tighten
collar screws that attach to the torsion bar to 12-14
ft./lbs. of torque. Securely tighten both set screws firmly,
without damaging the motor unit.
5. Fasten bracket securely with 14-10x1-7/8" screws.
Tighten all mounting bracket hardware.
NOTE: The motor unit does not have to be flush to wall.
6. Use a staple to secure the antenna wire to prevent
antenna from being entangled in a door roller.
Motor unit
Torsion Bar
Staple
HARDWARE SHOWN ACTUAL SIZE
14-10x1-7/8" Hex Screw
7
INSTALLATION STEP 2
Attach the Emergency Release Rope
and Handle
To prevent possible SERIOUS INJURY or DEATH from a falling
garage door:
• If possible, use emergency release handle to disengage door
ONLY when garage door is CLOSED. Weak or broken springs
or unbalanced door could result in an open door falling
rapidly and/or unexpectedly.
• NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
• Thread one end of the rope through the hole in the top
of the red handle so “NOTICE” reads right side up as
shown. Secure with an overhand knot at least 1"
(2.5 cm) from the end of the rope to prevent slipping.
• Thread the other end of the rope through the loop in the
emergency release cable.
• Adjust rope length so the handle is no higher than 6'
(1.83 m) above the floor. Secure with an overhand knot.
NOTE: If it is necessary to cut the rope, heat seal the cut
end with a match or lighter to prevent unraveling.
Motor Unit
Emergency
Release Cable
Overhand
Knot
Rope
Emergency
Release Handle
NOTI
CE
Overhand
Knot
Figure 1
INSTALLATION STEP 3
Install Power Door Lock
TOP
DRIL
L 5/16
"
DRIL
L 3/4"
132A2505
L 5/16
"
Approx. 3"
(7.6 cm)
Garage
Door Track
Lock Template
TOP
DRIL
L 5/16
"
DRIL
L 3/4"
Roller
Figure 2
HARDWARE SHOWN ACTUAL SIZE
Lock Screw
1/4-20 x 1/2" (2)
DRIL
132A2505
The lock is used to prevent the garage door from
being manually opened once the door is fully
closed.
1. Select a door roller to mount the lock above.
Check for clearance. If possible select a roller on
the same side of the door as the motor unit. The
second roller up from the bottom is ideal in most
installations.
2. Ensure rail surface is clean and adhere lock
template to achieve a 3" (7.6 cm) distance
between the center of the roller and the pin hole
(Figure 1).
3. Drill holes as marked on the template.
4. Fasten power door lock to the outside of the garage
door track with hardware provided.
5. Run bell wire up wall to motor unit. Use insulated
staples to secure wire in several places.
6. Plug connector into the motor unit (Figure 2).
NOTE: Lock must be mounted within 10' of the power
head.
Staples
8
DRIL
L 5/16
"
Figure 1
INSTALLATION STEP 4
Attach the Cable Tension Monitor
(Required)
Opener
Torsion Bar
This opener comes standard with the cable tension
monitor. It is supplied as a device to monitor the
cables for ANY slack that may occur and will reverse
the door when excessive slack is detected, eliminating
service calls.
The cable tension monitor MUST be connected and
properly installed before the garage door opener will
move in the down direction.
NOTE: The cable tension monitor is shipped for left side
installation. It is preferred that the cable tension monitor
be installed on the same side of the door as the opener.
If required, it can be mounted on the opposite side of door.
Remove the snap-ring holding the roller in place and
reassemble it on the opposite side of the cable tension
monitor.
1. Position the cable tension monitor as shown
(Figures 1 and 2). The cable tension monitor should be
located as close to the drum as possible.
NOTE: There must be no obstructions in the installation
area that prevent the cable tension monitor or the cable
itself from closing completely when slack is detected.
2. Make sure cable tension monitor is located over a wood
support member.
NOTE: If the cable tension monitor can not be mounted
into wood with the lag screws provided, it can be mounted
into 1/2" or greater drywall using the wall anchors (2) and
the #8 hex head screws (2) provided in the hardware bag.
3. Mark and drill 3/16" pilot holes for screws (pilot holes
are not required for anchors).
4. Attach the cable tension monitor to the wall using the
hardware provided. Make sure that the roller is on top of
the cable.
5. Run bell wire to motor unit. Use insulated staples to
secure wire in several places.
6. Connect bell wire to the green quick-connect terminals
(polarity is not important) (Figure 3).
NOTE: Cable must have tension through entire travel.
Make sure there is no slack in cable on opposite side of
garage door during normal operation. If this condition
exists, adjust cables as required.
Drum
Cable
2"-6"
(5 cm15 cm)
1/8"-1/4"
(3 mm-6 mm)
Cable
Tension
Monitor
Cable Tension
Monitor Roller
With Door Closed
Preferred Orientation
Figure 2
Wall
Drum
Cable
3/4" Min.
(18 mm Min.)
Figure 3
WHT/GRN
Cable Tension
Monitor
7/16" (11mm)
WHT/GRN
Strip wire 7/16" (11mm)
HARDWARE SHOWN ACTUAL SIZE
To insert or release wire,
push in tab with
screwdriver tip
#8 Hex Head Screw (2)
Screw #6 (2)
Staples
Wall Anchor (2)
9
INSTALLATION STEP 5
Install the Door Control
To prevent possible SERIOUS INJURY or DEATH from
electrocution:
• Be sure power is not connected BEFORE installing door control.
• Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing
garage door:
• Install door control within sight of garage door, out of reach of
children at a minimum height of 5 feet (1.5 m) and away from
ALL moving parts of door.
• NEVER permit children to operate or play with door control push
buttons or remote controls.
• Activate door ONLY when it can be seen clearly, is properly
adjusted and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed.
NEVER permit anyone to cross path of closing garage door.
Locate door control within sight of door, at a minimum
height of 5' (1.5 m) where small children cannot reach,
away from moving parts of door and door hardware. If
installing into drywall, drill 5/32" holes and use the anchors
provided. For pre-wired installations (as in new home
construction), it may be mounted to a single gang box
(Figure 1).
NOTE: The functional temperature range of the door
control is between -20°C (-4°F) and +50°C (+122°F).
Scroll speed of display is slower at lower temperatures
although the door control remains fully functional.
CAUTION: Continuous exposure of the door control to
temperatures below -22°F (-30°C) may damage the LCD
screen.
SPECIAL NOTE: Only one 398LM can be connected to
each garage door opener. If additional wall controls are
desired to operate the same garage door opener, it is
recommended to use model 378LM wireless wall control
as the secondary door control.
1. Strip 7/16" (11 mm) of insulation from one end of bell
wire and connect to the two screw terminals on back of
door control by color: white wire to the W (2) and
white/red wire to the R (1) (Figure 2).
2. Remove push bar cover by gently prying at the
lower/middle portion of the cover with a small flat-head
screwdriver. Fasten with 6AB x 1-1/4" self-tapping
screws (drywall installation) or 6-32 x 1" machine
screws (into gang box) as follows:
• Install bottom screw, allowing 1/8" (3 mm) to protrude
above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid cracking
plastic housing. Do NOT overtighten.
• Replace cover by inserting top tabs first and then snap
cover in place.
3. (For standard installations ONLY) Run bell wire up
wall and across ceiling to motor unit. Use insulated
staples to secure wire in several places. Do NOT pierce
wire with a staple, creating a short or open circuit.
4. Strip 7/16" (11 mm) of insulation from end of bell wire.
Connect bell wire to the quick-connect terminals on the
motor unit: white to white and white/red to red
(Figure 3).
NOTE: DO NOT connect the power and operate the
opener at this time. The door will travel to the full open
position but will not return to the close position until the
sensor beams are connected and properly aligned. See
page 14.
HARDWARE SHOWN ACTUAL SIZE
Insulated
Staples
Screw 6ABx1-1/4"
(standard installation)
Screw 6-32x1"
(pre-wired)
Drywall Anchors
REMOVE & REPLACE COVER
PRE-WIRED INSTALLATION
To Replace Insert
Top Tabs First
Push Bar Cover
LOCK
LIGHT
Figure 1
LOCK
2-Conductor
Bell Wire
24 Volt Bell Wire
Push Bar
W
2
R
1
LIGHT
Door
Control
Terminal
Screws
(BACK VIEW)
LOC
K
Lock
Button
Figure 2
LOC
K
Light
Button
7/16" (11 mm)
Strip wire 7/16" (11 mm)
Door Control
Connections
Figure 3
10
WHT/RED
WHT
To insert or release wire,
push in tab with
screwdriver tip
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of SEVERE INJURY or DEATH:
1. This portable luminaire has a polarized plug (one blade is
wider than the other) as a feature to reduce the risk of
electric shock.
2. This plug will fit in a polarized outlet ONLY one way.
3. If the plug does not fit fully in the outlet, reverse the plug.
4. If it still does not fit, contact a qualified electrician.
5. NEVER use with an extension cord unless plug can be fully
inserted.
6. DO NOT alter the plug.
7. Light is intended for ceiling mount and indoor applications
ONLY.
INSTALLATION STEP 6
Install the Light
To prevent possible OVERHEATING of the endpanel or light
socket:
• DO NOT use short neck or specialty light bulbs.
• DO NOT use halogen bulbs. Use ONLY incandescent.
To prevent damage to the opener:
• DO NOT use bulbs larger than 100W.
• ONLY use A19 size bulbs.
The remote light (opener light) is designed to plug directly
into a standard 120V outlet.
1. Install the hinge and latch clips. Clips slide in between
the metal plate and the plastic housing on each side of
the light base (Figure 1).
2. Select an appropriate location on the ceiling to mount
the light within 6' (1.8 m) of an electrical outlet so that
the cord and light are away from moving parts.
3. Install the ceiling mount plate with the screws provided.
Leave 1/8" (3.1 mm) of the thread exposed between the
ceiling and the screw head (Figure 2).
NOTE: If installing remote light (opener light) on drywall
and a ceiling joist can not be located, use wall anchors
provided. No pilot hole is required for wall anchors.
4. Determine the length of power cord needed to reach the
nearest outlet. Wind any excess cord around cord
retainer on the top side of the light base.
5. Install the light base by pushing onto the screws and
turning the base clockwise to lock the light in place.
6. Install two Type A19 incandescent or compact
fluorescent bulbs. 100 watt maximum per bulb,
200 watts total.
7. Install the light lens by hooking one end of the lens over
the hinge and pressing up on the other end to latch into
place (Figure 3).
8. Plug in the light to outlet.
NOTE: Light will not operate until the unit is activated.
Figure 1
Light Clip Screw
Latch Clip
Light
Base
Plastic
Housing
Metal
Plate
Figure 2
Wall Anchors
Cord
Retainer
Scews
Figure 3
HARDWARE SHOWN ACTUAL SIZE
Light Clip Screw
#4-20 X 7/16" (2)
Light Clip
Screw
100 Watt (max)
Screw #6x1" (2)
Light
Lens
Wall Anchor (2)
11
Hinge Clip
INSTALLATION STEP 7
Electrical Requirements
To prevent possible SERIOUS INJURY or DEATH from
electrocution or fire:
• Be sure power is not connected to the opener, and
disconnect power to circuit BEFORE removing cover to
establish permanent wiring connection.
• Garage door installation and wiring MUST be in compliance
with ALL local electrical and building codes.
• NEVER use an extension cord, 2-wire adapter or change plug
in any way to make it fit outlet. Be sure the opener is
grounded.
To avoid installation difficulties, do not run the opener
at this time.
To reduce the risk of electric shock, your garage door
opener has a grounding type plug with a third grounding
pin. This plug will only fit into a grounding type outlet. If
the plug doesn't fit into the outlet you have, contact a
qualified electrician to install the proper outlet.
PERMANENT WIRING CONNECTION
RIGHT
Flexible conduit
WRONG
Green
Ground
Screw
If permanent wiring is required by your local code,
refer to the following procedure.
To make a permanent connection through the 7/8" hole in
the back of the motor unit (according to local code):
• Remove the opener from the torsion bar, remove cover
screws and set the cover aside.
• Remove the attached green ground terminal.
• Cut black and white wires and strip away 1/2" (1.3 cm)
of insulation, 3" (7.6 cm) before spade terminals.
• Remove the power cord from unit.
• Install a 90 conduit or flex cable adapter to the 7/8"
hole. Reinstall opener to torsion bar.
• Run wires through conduit, cut to proper length and strip
insulation.
• Attach with wire nuts provided.
• Properly secure wire under plastic ties so that wire does
not come in contact with moving parts.
• Reinstall the cover.
To avoid installation difficulties, do not run the opener
at this time.
Ground Tab
Ground Wire
Black Wire
From Power Cord
White Wire
From Power Cord
o
PERMANENT WIRING CONNECTION
Black Wire
Green Wire
90˚ Connector
12
White Wire
INSTALLATION STEP 8
Mount the Standby Power Unit (SPU)
(not provided)
475LM
Standby
475RGD
Standby
Power
Power System
System
If the optional 475RGD Standby Power Unit is part of this
installation it should be installed at this time.
• The SPU can be mounted to either the ceiling or a wall
within 3' (.9 m) of the motor unit.
• Position the SPU as desired to a structural support
(ceiling joist or wall stud).
• Attach the SPU to the support using the mounting holes
on either side of the SPU.
• Secure the SPU using the 1-1/2" lag screws (2) provided
with the SPU unit.
• Connect the SPU cord into the connector on the bottom
of the motor unit.
• Follow all instructions included with the 475RGD unit to
test for proper operation and testing of the SPU.
SPU Cord
Connector
13
INSTALLATION STEP 9
Install The Protector System®
Be sure power is not connected to the garage door opener
BEFORE installing the safety reversing sensor.
To prevent SERIOUS INJURY or DEATH from a closing garage
door:
• Correctly connect and align the safety reversing sensor. This
required safety device MUST NOT be disabled.
• Install the safety reversing sensor so beam is NO HIGHER
than 6" (15 cm) above garage floor.
The safety reversing sensor must be connected and
aligned correctly before the garage door opener will
move in the down direction. This is a required safety
device and cannot be disabled.
IMPORTANT INFORMATION ABOUT THE SAFETY
REVERSING SENSOR
When properly connected and aligned, the safety
reversing sensor will detect an obstacle in the path of its
electronic beam. The sending eye (with an amber indicator
light) transmits an invisible light beam to the receiving eye
(with a green indicator light). If an obstruction breaks the
light beam while the door is closing, the door will stop and
reverse to full open position, and the opener lights will
flash 10 times.
The units must be installed inside the garage so that the
sending and receiving eyes face each other across the
door, no more than 6" (15 cm) above the floor. Either can
be installed on the left or right of the door as long as the
sun never shines directly into the receiving eye lens.
The mounting brackets are designed to clip onto the track
of sectional garage doors without additional hardware.
Safety Reversing Sensor
6" (15 cm) max. above floor
If it is necessary to mount the units on the wall, the
brackets must be securely fastened to a solid surface
such as the wall framing. Extension brackets (see
Accessories) are available if needed. If installing in
masonry construction, add a piece of wood at each
location to avoid drilling extra holes in masonry if
repositioning is necessary.
The invisible light beam path must be unobstructed. No
part of the garage door (door tracks, springs, hinges,
rollers or other hardware) may interrupt the beam while
the door is closing.
Safety Reversing Sensor
6" (15 cm) max. above floor
Invisible Light Beam
Protection Area
Facing the door from inside the garage
14
INSTALLING THE BRACKETS
Figure 1
Be sure power to the opener is disconnected. Install
and align the brackets so the safety reversing sensors will
face each other across the garage door, with the beam no
higher than 6" (15 cm) above the floor. They may be
installed in one of three ways,as follows.
DOOR TRACK MOUNT (RIGHT SIDE)
Door
Track
Lip
Indicator
Light
Garage door track installation (preferred)
(Figure 1):
• Slip the curved arms over the rounded edge of each
door track, with the curved arms facing the door. Snap
into place against the side of the track. It should lie flush,
with the lip hugging the back edge of the track, as shown
in Figure 1.
If your door track will not support the bracket securely, wall
installation is recommended.
Sensor
Bracket
ide
Ins age
r
a
G l
l
Wa
Figure 2
Wall installation (Figure 2 and 3):
• Place the bracket against the wall with curved arms
facing the door. Be sure there is enough clearance for
the sensor beam to be unobstructed.
• If additional depth is needed, an extension bracket
(see Accessories) or wood blocks can be used.
• Use bracket mounting holes as a template to locate and
drill (2) 3/16" diameter pilot holes on the wall at each
side of the door, no higher than 6" (15 cm) above the
floor.
• Attach brackets to wall with lag screws (not provided).
• If using extension brackets or wood blocks, adjust right
and left assemblies to the same distance out from the
mounting surface. Make sure all door hardware
obstructions are cleared.
Lens
WALL MOUNT (RIGHT SIDE)
Fasten Wood Block to Wall with
Lag Screws (Not Provided)
Indicator
Light
Sensor
Bracket
Lag Screws
(Not Provided)
Lens
Figure 3
WALL MOUNT (RIGHT SIDE)
ide
Ins age
r
Ga l
l
Wa
Extension
Bracket
(See Accessories)
(Provided with
Extension Bracket)
Floor installation (Figure 4):
• Use wood blocks or extension brackets
(see Accessories) to elevate sensor brackets so the
lenses will be no higher than 6" (15 cm) above the floor.
• Carefully measure and place right and left assemblies at
the same distance out from the wall. Be sure all door
hardware obstructions are cleared.
• Fasten to the floor with concrete anchors as shown.
Sensor
Bracket
(Provided with
Extension
Bracket)
Lens
Figure 4
Indicator
Light
FLOOR MOUNT (RIGHT SIDE)
HARDWARE SHOWN ACTUAL SIZE
Carriage Bolt
1/4"-20x1/2"
Wing Nut
1/4"-20
Attach with
Concrete Anchors
(Not Provided)
ide
Ins rage
a
G ll
Wa
Staples
Lens
Indicator
Light
Sensor
Bracket
15
MOUNTING AND WIRING THE SAFETY REVERSING
SENSORS
• Slide a 1/4"-20x1/2" carriage bolt head into the slot on
each sensor. Use wing nuts to fasten safety reversing
sensors to brackets, with lenses pointing toward each
other across the door. Be sure the lens is not obstructed
by a bracket extension (Figure 5).
• Finger tighten the wing nuts.
• Run the wires from both safety reversing sensors to the
opener. Use insulated staples to secure wire to wall
and ceiling.
• Strip 7/16" (11 mm) of insulation from each set of wires.
Separate white and white/black wires sufficiently to
connect to the opener quick-connect terminals: white to
white and white/black to grey (Figure 6).
Figure 5
Wing Nut
1/4"-20
Carriage Bolt
1/4"-20x1/2"
Lens
TROUBLESHOOTING THE SAFETY REVERSING
SENSORS
1. If the sending eye indicator light does not glow steadily
after installation, check for:
• Electric power to the opener.
• A short in the white or white/black wires. These can
occur at staples, or at opener connections.
• Incorrect wiring between safety reversing sensors and
opener.
• A broken wire.
2. If the sending eye indicator light glows steadily but the
receiving eye indicator light doesn't:
• Check alignment.
• Check for an open wire to the receiving eye.
3. If the receiving eye indicator light is dim, realign
either sensor.
NOTE: When the invisible beam path is obstructed or
misaligned while the door is closing, the door will reverse.
If the door is already open, it will not close.
The remote lights will blink 10 times. (If bulbs are not
installed, 10 clicks can be heard.) See page 11.
ALIGNING THE SAFETY REVERSING SENSORS
• Plug in the opener. The indicator lights in both the
sending and receiving eyes will glow steadily if wiring
connections and alignment are correct.
The sending eye amber indicator light will glow regardless
of alignment or obstruction. If the green indicator light in
the receiving eye is off, dim, or flickering (and the invisible
light beam path is not obstructed), alignment is required.
• Loosen the sending eye wing nut and readjust, aiming
directly at the receiving eye. Lock in place.
• Loosen the receiving eye wing nut and adjust the safety
reversing sensor until it receives the sender’s beam.
When the green indicator light glows steadily, tighten the
wing nut.
Bell Wire
Motor unit
Figure 6
Bell Wire
To CableTension Monitor
Connect Wire to
Quick-Connect
Terminals
To Power
Door Lock
Sensor
Connections
WHT/RED
WHT
To Door Control
Power Door Lock
WHT/BLK
WHT
Quick-Connect Terminals
To insert or release wires, push
in tab with screwdriver tip.
Sensor Sensor
Safety Reversing
16
Safety Reversing Sensor
Sensor
Invisible Light Beam
Protection Area
ADJUSTMENT STEP 1
Program the Travel Limits
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLY INJURED or
KILLED by a closing garage door.
• NEVER learn forces or limits when door is binding or
sticking. Repair door first.
• Incorrect adjustment of garage door travel limits will
interfere with proper operation of safety reversal system.
• After ANY adjustments are made, the safety reversal system
MUST be tested. Door MUST reverse on contact with 1-1/2"
high (3.8 cm) object (or 2x4 laid flat) on floor.
Travel limits regulate the points at which the door will
stop when moving up or down. Follow the steps below
to set the limits.
Figure 1
Indicator
Light
Black
Button
Purple
Button
To program the travel limits:
Adjust the position of the door by using the black and
purple buttons. Black moves the door UP (open) and
purple moves the door DOWN (close).
1. Setting the UP position: Press and hold the black
button until the yellow indicator light starts flashing
slowly then release.
2. Push and hold the black button until the door reaches
the desired UP (open) position (Figure 2).
NOTE: Check to be sure the door opens high enough for
your vehicle.
3. Push the remote control or door control (Figure 3). This
sets the UP (open) limit and begins closing the door.
NOTE: Excessive movement of the motor unit will cause
premature wear. See Troubleshooting section.
4. Immediately when the door begins to move down, press
and release either the black or purple button. This will
stop the door.
5. Setting the DOWN position: Push and hold the purple
button until the door reaches the desired DOWN
(closed) position (Figure 4).
6. Once the door is closed, check for proper pressure on
the door (you should be able to manually push the door
down a 1/16 of an inch). If there appears to be too
much pressure on the door, you may toggle the door
back and forth using the black and purple buttons to
reach the desired position.
7. Push the remote control or the door control (Figure 3).
This sets the DOWN (close) limit and should bring the
door to the open position.
• If the opener is not stopping exactly where you would
like it, repeat steps 1 through 7 and program the limits
again.
• When the unit stops in both the desired up (open) and
down (close) positions, proceed to Adjustment Step 2,
Setting the Force.
To prevent damage to vehicles, be sure fully open door
provides adequate clearance.
Figure 2
BLACK
Push and hold
until the door
is at desired UP
position
PURPLE
Figure 3
or
LOC
K
LIG
Figure 4
BLACK
Push either
button to stop
door at desired
DOWN position
PURPLE
17
HT
ADJUSTMENT STEP 2
Setting the Force
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLY INJURED or
KILLED by a closing garage door.
• NEVER learn forces or limits when door is binding or
sticking. Repair door first
• Too much force on garage door will interfere with proper
operation of safety reversal system.
• After ANY adjustments are made, the safety reversal system
MUST be tested. Door MUST reverse on contact with 1-1/2"
high (3.8 cm) object (or 2x4 laid flat) on floor.
The force setting button is located on the front panel.
The force setting measures the amount of force
required to open and close the door.
1. Locate the purple button on the unit (Figure 1).
2. Push the purple button twice to enter unit into Force
Adjustment Mode (Figure 2). The LED (Indicator Light)
will flash quickly.
3. Push the remote control or door control (Figure 3). The
door will travel to the DOWN (close) position. Push the
remote control or door control again, the door will travel
to the UP (open) position. Push the remote control or
door control a third time to send the door to the DOWN
(close) position.
The LED (Indicator Light) will stop flashing when the force
has been learned.
The unit has learned the forces required to open and close
your door.
The door must travel through a complete cycle, UP and
DOWN, in order for the force to be set properly. If the unit
cannot open and close your door fully, inspect your door to
insure that it is balanced properly and is not sticking or
binding. See page 4, “Preparing your garage door.”
Figure 1
Indicator
Light
Figure 2
Black
Button
Push Purple button
twice to enter
unit into Force
Adjustment Mode
PURPLE
Purple
Button
Figure 3
or
LOC
K
LIG
18
BLACK
HT
ADJUSTMENT STEP 3
Test the Safety Reversal System
Without a properly installed safety reversal system, persons
(particularly small children) could be SERIOUSLY INJURED or
KILLED by a closing garage door.
• Safety reversal system MUST be tested every month.
• If one control (force or travel limits) is adjusted, the other
control may also need adjustment.
• After ANY adjustments are made, the safety reversal system
MUST be tested. Door MUST reverse on contact with 1-1/2"
(3.8 cm) high object (or 2x4 laid flat) on the floor.
TEST
• With the door fully open, place a 1-1/2" (3.8 cm) board
(or a 2x4 laid flat) on the floor, centered under the
garage door.
• Operate the door in the down direction. The door must
reverse on striking the obstruction. Upon successful
safety reversal test proceed to Adjustment Step 4.
ADJUST
• If the door stops on the obstruction, it is not traveling far
enough in the down direction. Complete Adjustment
Steps 1 and 2 Programming the Limits and Forces.
• Repeat the test.
• When the door reverses on the 1-1/2" (3.8 cm) board
(or 2x4 laid flat), remove the obstruction and run the
opener through 3 or 4 complete travel cycles to test
adjustment.
• If the unit continues to fail the Safety Reverse Test, call
for a trained door systems technician.
IMPORTANT SAFETY CHECK:
Test the Safety Reverse System after:
• Each adjustment of limits, or force controls.
• Any repair to or adjustment of the garage door
(including springs and hardware).
• Any repair to or buckling of the garage floor.
• Any repair to or adjustment of the opener.
1-1/2" (3.8 cm) board
(or a 2x4 laid flat)
ADJUSTMENT STEP 4
Test The Protector System®
Without a properly installed safety reversing sensor, persons
(particularly small children) could be SERIOUSLY INJURED or
KILLED by a closing garage door.
• Press the remote control push button to open the door.
• Place the opener carton in the path of the door.
• Press the remote control push button to close the door.
The door will not move more than an inch, and the
opener lights will flash.
The garage door opener will not close from a remote if the
indicator light in either sensor is off (alerting you to the fact
that the sensor is misaligned or obstructed).
If the opener closes the door when the safety
reversing sensor is obstructed, do not operate the
door. Call for a trained door systems technician.
Safety Reversing Sensor
19
Safety Reversing Sensor
ADJUSTMENT STEP 5
Test Cable Tension Monitor
To prevent possible SERIOUS INJURY or DEATH from a falling
garage door:
• If possible, use emergency release handle to disengage door
ONLY when garage door is CLOSED. Weak or broken springs
or unbalanced door could result in an open door falling
rapidly and/or unexpectedly.
• NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
If your cable tension monitor has been activated the
Indicator Light will blink 9 times. See page 18.
ADJUSTMENT STEP 6
Test Power Door Lock
TEST
• With the door fully closed, the power door lock bolt
should be protruding through the track.
• Operate the door in the open direction. The power door
lock should retract before the door begins to move.
• Operate the door in the down direction. When the door
reaches the fully closed position, the power door lock
should automatically activate to secure the door.
NOTE: If the power door lock does not function, the lock
can be manually released by sliding the manual release
handle to the open position.
ADJUSTMENT STEP 7
To Open the Door Manually
Disengage door lock before proceeding. The door should
be fully closed if possible. Pull down on the emergency
release handle until a click noise is heard from the unit
and lift the door manually. To reconnect the door to the
opener, pull down the emergency release handle straight
down a second time until a click noise is heard from the
unit. The door will reconnect on the next UP or DOWN
operation.
Emergency
Release Handle
Test the emergency release:
• Make sure the garage door is closed.
• Pull the emergency release handle. The garage door
should then be able to be opened manually.
• Return the door to the closed position.
• Pull the emergency handle a second time.
• Reconnect the door to the opener.
NOT
ICE
Power Door Lock
Manual Release
Lock Bolt
“Locked”
20
WARNING
OPERATION
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of SEVERE INJURY or DEATH:
1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.
2. ALWAYS keep remote controls out of reach of children.
NEVER permit children to operate or play with garage door
control push buttons or remote controls.
3. ONLY activate garage door when it can be seen clearly, it is
properly adjusted and there are no obstructions to door
travel.
4. ALWAYS keep garage door in sight until completely closed.
NO ONE SHOULD CROSS THE PATH OF THE MOVING
DOOR.
5. NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY
OPENED DOOR.
6. If possible, use emergency release handle to disengage door
ONLY when garage door is CLOSED. Weak or broken
springs or unbalanced door could result in an open door
falling rapidly and/or unexpectedly.
7. NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
8. After ANY adjustments are made, the safety reversal
system MUST be tested.
9. Safety reversal system MUST be tested every month.
Garage door MUST reverse on contact with 1-1/2"
(3.8 cm) high object (or a 2x4 laid flat) on the floor.
10. ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED
(see page 3). An improperly balanced door may not
reverse when required and could result in SEVERE INJURY
or DEATH.
11. ALL repairs to cables, spring assemblies and other
hardware, ALL of which are under EXTREME tension,
MUST be made by a trained door systems technician.
12. ALWAYS disconnect electric power to garage door opener
BEFORE making ANY repairs or removing covers.
13.
Using Your Garage Door Opener
6. If obstructed while opening, the door will stop.
7. If fully open, the door will not close when the beam is
broken. The sensor has no effect in the opening cycle.
If the sensor is not installed, or is misaligned, the door
won’t close from a hand-held remote. However, you can
close the door with the Door Control, the Outside Keylock,
or Keyless Entry, if you activate them until down travel is
complete. If you release them too soon, the door will
reverse.
The opener lights will turn on when the opener is
activated. They will turn off automatically after 4-1/2
minutes or provide constant light when the Light feature on
the Smart Control Panel™ is activated. Bulb size is A19.
Bulb power is 100 watts maximum.
SAFETY SIGNAL light feature: Lights will also turn on when
someone walks through the open garage door. With a
Smart Control Panel™, this feature may be turned off as
follows: With the opener lights off, press and hold the light
button for 10 seconds, until the light goes on, then off
again. To restore this feature, start with the opener lights
on, then press and hold the light button for 10 seconds
until the light goes off, then on again.
Your SAFETY SIGNAL opener and hand-held remote control
have been factory-set to a matching code which changes
with each use, randomly accessing over 100 billion new
codes. Your opener will operate with up to eight
SAFETY SIGNAL remote controls and one SAFETY SIGNAL
Keyless Entry System. If you purchase a new remote,
or if you wish to deactivate any remote, follow the
instructions in the Programming section.
TM
TM
SAVE THESE INSTRUCTIONS.
TM
Activate your opener with any of the following:
• The hand-held Remote Control: Hold the large push
button down until the door starts to move.
• The wall-mounted Door Control: Hold the push button or
bar down until the door starts to move.
• The Keyless Entry (See Accessories): If provided with
your garage door opener, it must be programmed before
use. See Programming.
TM
When the opener is activated (with the safety
reversing sensor correctly installed and aligned)
1. If open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
3. If opening, the door will stop.
4. If the door has been stopped in a partially open position,
it will close.
5. If obstructed while closing, the door will reverse. If the
obstruction interrupts the sensor beam, the opener lights
will blink for five seconds.
21
Using the Wall-Mounted Door Control
THE SMART CONTROL PANEL™
Press the push bar to
Push Bar
open or close the door. Automatic Light
On/Off
Press again to reverse
Prog <Learn>
the door during the
Hour
closing cycle or to stop
Minute
the door while it's
Language
Light Button
opening.
Degrees (F/C)
Lock Button
This door control
contains a motion sensing detector that will automatically
turn on the light when it detects a person entering the
garage.
(PROG) Learn Feature
The door control is equipped with a Prog <LEARN> button
to assist in learning remote controls to the unit. Press the
Prog <LEARN> button once to initiate LEARN mode and
the display will show ‘Learn Remote Control - Press Learn
Button Again to Confirm’. Press the Prog <LEARN> button
a second time and the display will show ‘Learn Mode Press Remote Control Button to Learn Remote.’ Press the
button of the remote control to be learned and the
worklight will blink to confirm the remote control has
been learned.
T
LIGH
LOCK
Light feature
H
M
Hour & Minute Feature
LIGHT
Press or hold either of these side buttons to increment the
hour or minute displayed on the LCD display.
Press the Light button to turn the opener light on or off. It
will not control the opener lights when the door is in
motion. If you turn it on and then activate the opener, the
light will remain on for 4-1/2 minutes. Press again to turn it
off sooner. The 4-1/2 minute interval can be changed to
1-1/2, 2-1/2, or 3-1/2 minutes as follows: Press and hold
the Lock button until the light blinks (about 10 seconds). A
single blink indicates that the timer is reset to 1-1/2
minutes. Repeat the procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes. Repeat again
for a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.
When using the opener lights as working lights, we
recommend that you first disable the motion sensor. See
Automatic Light Feature, below.
Motion Sensing (Automatic Light Feature): The opener
light will turn on automatically when a person enters the
garage. When a person walks in front of the door control,
the light will come on for five minutes, then shut off. This
feature works by detecting body heat.
(LANG) Language Feature
Press this side button to toggle between the three
languages - English, French and Spanish.
Degrees F/C Feature
Press this side button to toggle the temperature units
between Fahrenheit and Celsius.
Display Contrast Adjustment
Press and hold the light button then push the hour button
to increase the contrast or the minute button to decrease
the contrast.
To disable this feature, push the motion sensing
button on the side of the door control.
We recommend that you disable the motion sensor when
using the opener lights as working lights. Otherwise, they
will turn off automatically if you are working beyond the
sensors range.
Lock feature
LOCK
Designed to prevent operation of the door from
hand-held remote controls. However, the door will open
and close from the Door Control, the Outdoor Key Switch
and the Keyless Entry Accessories.
To activate, press and hold the Lock button for 2 seconds.
To turn off, press and hold the Lock button again for
2 seconds. The Lock feature will also turn off whenever the
“learn” button on the motor unit panel is activated.
22
Using the Remote Control
The Remote Control Battery
NOTE: To activate the remote control functions, pull out
the plastic pull tab protruding from the remote control
housing.
This remote control is equipped with a proximity lighting
feature. When moving a hand within close proximity to the
remote control, the LED lights turn on for 3 seconds. Upon
successful activation of a remote control button, the LED
lights will blink rapidly.
Proximity Disable Feature
The remote control will turn off the proximity lighting
feature if the proximity lighting is turned on 10 consecutive
times without activation of a button. To re-enable the
proximity lighting, simply press a button. This function
conserves battery life.
To Control the Opener Lights
With 315MHz SAFETY SIGNAL remote controls, a remote
push button can be programmed to operate the opener
lights without opening the door.
1. With the door closed, press and hold the remote button
that you want to control the light.
2. Press and hold the Light button on the multi-function
control panel.
3. Press and hold the Lock button on the multi-function
control panel.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener
lights should turn on or off but the door should not move.
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2016 or 3V2450 coin batteries.
• Do NOT recharge, disassemble, heat above 100°C (212°F)
or incinerate.
The 3V2016 lithium batteries for the opener and LED
lights (marked “LED and Opener Battery”) should last 5
years. The 3V2450 lithium battery for the proximity lighting
(marked “Proximity Battery”) should last 1-2 years.
TM
To replace the batteries,
remove the two screws and
open the remote control
Proximity
housing. Push the battery
Battery
out of the holder for removal.
Insert replacement batteries
positive side up. Dispose of
LED and
old batteries properly.
Spring
Opener
Contact
Batteries
Replace the batteries with
only 3V2016 or 3V2450 coin
cell batteries.
CAUTION: Do not bend spring contact. If bent the
proximity sensor will not work.
Troubleshooting
PROBLEM
SOLUTION
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Check if proximity lighting is
disabled by pressing a button.
Reduced proximity
sensing (does not
activate by
touching top of
remote control)
The Proximity Sensor may be
oversensitized. Sit remote control
undisturbed for 60 seconds on a
non-metallic surface. This allows
the sensor to recalibrate itself.
Replace 3V2450 battery with
same type 3V2450 coin cell.
Dim LED lights
Replace two 3V2016 batteries
with same type 3V2016 coin
cells.
No rapid LED
blinking after
pressing a button
Replace two 3V2016 batteries
with same type 3V2016 coin
cells.
23
CARE OF YOUR OPENER
MAINTENANCE SCHEDULE
Once a Month
• Manually operate door. If it is unbalanced or binding, call
a trained door systems technician.
• Check to be sure door opens & closes fully. Adjust limits
and/or force if necessary (see Adjustment Steps
1 and 2).
• Repeat the safety reverse test. Make any necessary
adjustments (see Adjustment Step 3).
Once a Year
• Oil door rollers, bearings and hinges. The opener does
not require additional lubrication. Do not grease the door
tracks.
HAVING A PROBLEM?
(TROUBLESHOOTING)
1. The opener doesn't operate from either the Door
Control or the remote control:
• Does the opener have electric power? Plug a lamp into
the outlet. If it doesn't light, check the fuse box or the
circuit breaker. (Some outlets are controlled by a wall
switch.)
• Have you disabled all door locks? Review installation
instruction warnings on page 7.
• Is there a build-up of ice or snow under the door? The
door may be frozen to the ground. Remove any
restriction.
• The garage door spring may be broken. Have it
replaced (see page 3 for reference).
5. The garage door opens and closes by itself:
• Be sure that all remote control push buttons are off.
• Remove the bell wire from the door control terminals
and operate from the remote only. If this solves the
problem, the door control is faulty (replace), or there is
an intermittent short on the wire between the control
console and the motor unit.
• Clear memory and re-program all remote controls.
6. The door doesn't open completely:
• Check power door lock.
• Is something obstructing the door? Is it out of balance,
or are the springs broken? Remove the obstruction or
repair the door.
7. The door opens but won't close:
• Check cable tension monitor (see Installation Step 4).
• If the opener lights blink, check the safety reversing
sensor. See Installation Step 9.
• If the opener lights don’t blink and it is a new
installation. See Adjustment Step 2. For an existing
installation, see below.
Repeat the safety reverse test after the adjustment
is complete.
2. Opener operates from the remote, but not from the
Door Control:
• Is the door control lit? If not, reverse the wires. If the
opener runs, check for a faulty wire connection at the
control console, a short under the staples, or a broken
wire.
• Are the wiring connections correct? Review Installation
Step 5, page 10.
3. The door operates from the Door Control, but not
from the remote control:
• Is the door push bar flashing? If so, Lock mode is
engaged. Make sure it is off by pressing the Lock button
for two seconds.
• Program the opener to match the remote control code.
(Refer to instructions on the motor unit panel.) Repeat
with all Remote.
8. The door reverses for no apparent reason and
opener lights don’t blink:
• Check cable tension monitor (see installation step 4).
• Is something obstructing the door? Pull the emergency
release handle. Operate the door manually. If it is
unbalanced or binding, call a trained door systems
technician.
• Clear any ice or snow from the garage floor area
where the door closes.
• Review Adjustment Step 2.
Repeat safety reverse test after adjustments.
4. The remote control has short range:
• Change the location of the remote control in your car.
• Check to be sure the antenna on the side or back panel
of motor unit extends fully downward.
• Some installations may have shorter range due to a
metal door, foil backed insulation, or metal garage
siding.
24
Having a Problem? (Continued)
9. The door reverses for no apparent reason and
opener lights blink for 5 seconds after reversing:
• Check the safety reversing sensor. Remove any
obstruction or align the receiving eye. See Installation
Step 9.
13. Door loses limits.
• Collar not tightened securely. Tighten collar
(see Assembly Steps 1 and 2) and reprogram limits
(see Adjustment Step 1).
14. The operator moves when the door is in operation:
• Some minor movement is normal for this product. If it
is excessive the collar will wear prematurely.
• Check to make sure the torsion bar is not moving
left/right excessively.
• Check to make sure the torsion bar is not visibly
moving up and down as it rotates.
• Check that the operator is mounted at a right angle to
the jackshaft. If not, move the position of the mounting
bracket.
15. Power lock makes noise when operating.
• Call dealer for replacement power lock.
10. The opener strains to operate door:
• The door may be out of balance or the springs may be
broken. Close the door and use the emergency
release handle to disconnect the door. Open and close
the door manually. A properly balanced door will stay
in any point of travel while being supported entirely by
its springs. If it does not, disconnect the opener and
call a trained door systems technician.
11. The opener motor hums briefly, then won't work:
• The garage door springs may be broken. See above.
• If the problem occurs on the first operation of the
opener, door may be locked. Disable the power door
lock.
12. The opener won't operate due to power failure:
• Manually open the power door lock.
• Use the emergency release handle to disconnect the
door. The door can be opened and closed manually.
When power is restored, pull manual release a second
time.
• If a Standby Power Unit is connected, the opener
should be able to operate up to 20 times without
power.
25
Smart Control Panel™ Messages
The following messages are contained within the Smart Control Panel™ and may appear during the operations of
the unit:
Message
SAFETY SENSORS
CHECK ALIGNMENT,
BLOCKAGE OR
MISWIRING. SEE
OWNER’S MANUAL.
Message
SAFETY SENSORS
MALFUNCTION.
CHECK MISWIRING.
SEE OWNER’S
MANUAL.
Message
LEARN REMOTE
CONTROL. PRESS
LEARN BUTTON TO
CONFIRM.
Message
LEARN MODE.
PRESS REMOTE
CONTROL BUTTON
TO PROGRAM
REMOTE.
Message
LOCK MODE.
REMOTE CONTROL
LOCKED OUT.
PRESS LOCK
BUTTON TO ENABLE
REMOTE.
Message
ENGLISH, FRANÇAIS
AND ESPAÑOL.
Message
MOTION SENSING
ON, MOTION
SENSING OFF.
Meaning: This message will appear if the Safety Reversing Sensors are out of
alignment, if they are blocked or if the wiring is disconnected. To clear message
from Smart Control Panel™ do the following:
• Check to see that area is clear between the Safety Reversing Sensors.
• Check to see that the Safety Reversing Sensors are not misaligned.
• Realign receiving eye sensor, clean lens and secure brackets.
• Verify door track is firmly secured to wall and does not move.
• Check to see that the Safety Reversing Sensors’ wires are connected to the motor unit.
• If message has not cleared after the above checks, refer to message #2.
Meaning: This message will appear if the Safety Reversing Sensors are miswired.
To clear the message, do the following:
• Inspect the safety sensor wires for a short (staple in wire), correct wiring polarity
(black/white wires reversed), replace/attach as needed.
• Disconnect all wires from back of motor unit.
• Remove safety sensors from brackets and shorten sensor wires to 1-2 ft. (30-60 cm)
from back of each sensor.
• Reattach sending eye to motor unit using shortened wires. If sending eye indicator light
glows steadily, attach the receiving eye.
• Align sensors, if the indicator lights glow replace the wires for the sensors. If the sensor
indicator lights do not light, replace the safety sensors.
Meaning: This message will appear when the Prog <LEARN> button has been
pressed on the Smart Control Panel™. Pressing the Prog <LEARN> button again will
allow the user to program an additional remote control to the opener.
Meaning: This message will appear when the Prog <learn> button has been pressed
a second time on the Smart Control Panel™ or anytime on the opener. The opener is
ready to program another remote control by simply pressing the remote control
button. Once the opener has ‘LEARNED’ the remote control, the worklight will blink
one time.
Meaning: This message will appear when the ‘Lock’ button has been pressed and
held for more than one second. This feature will disable the opener from receiving
remote control signals. To exit ‘LOCK’ mode, press and hold the button for more
than one second.
Meaning: This message will appear when the ‘Language’ button has been pressed.
Pressing the button will toggle to the next language.
Meaning: This message will appear when the ‘MOTION SENSING’ button is pressed.
The Motion Detector will toggle on or off with each press of the button.
26
Motor
Unit
Installed
Safety Reversing
Sensor
“Learn”
Button LED
or Diagnostic
LED
“Learn”
Button
Your garage door opener is programmed with self-diagnostic
capabilities. The “Learn” button/diagnostic LED will flash a
number of times then pause signifying it has found a
potential issue. Consult Diagnostic Chart below.
Diagnostic Chart
1 FLASH
Safety reversing sensors
wire open (broken or
disconnected).
OR
2 FLASHES
Safety reversing sensors
wire shorted or
black/white wire reversed.
3 FLASHES
Door control or
wire shorted.
4 FLASHES
Safety reversing sensors
slightly misaligned
(dim or flashing LED).
5 FLASHES
Motor overheated or
possible RPM sensor
failure. Unplug to reset.
9 FLASHES
Cable tension monitor
reversal.
Symptom: One or both of the Indicator lights on the safety reversing sensors
do not glow steady.
• Inspect sensor wires for a short (staple in wire), correct wiring polarity (black/white
wires reversed), broken or disconnected wires, replace/attach as needed.
• Disconnect all wires from back of motor unit.
• Remove sensors from brackets and shorten sensor wires to 1-2 ft (30-60 cm) from
back each of sensor.
• Reattach sending eye to motor unit using shortened wires. If sending eye indicator
light glows steadily, attach the receiving eye.
• Align sensors, if the indicator lights glow replace the wires for the sensors. If the
sensor indicator lights do not light, replace the safety reversing sensors.
Symptom: LED is not lit on door control.
• Inspect door control/wires for a short (staple in wire), replace as needed.
• Disconnect wires at door control, touch wires together. If motor unit activates,
replace door control.
• If motor unit does not activate, disconnect door control wires from motor unit.
Momentarily short across red and white terminals with jumper wire. If motor unit
activates, replace door control wires.
Symptom: Sending indicator light glows steadily, receiving indicator light is
dim or flashing.
• Realign receiving eye sensor, clean lens and secure brackets.
• Verify door track is firmly secured to wall and does not move.
Symptom: Motor has overheated; the motor unit does not operate = Motor unit
hums briefly; RPM Sensor = Short travel 6-8" (15-20 cm).
• Unplug unit to reset. Try to operate motor unit, check diagnostic code.
• If it is still flashing 5 times and motor unit moves 6-8" (15-20 cm), replace RPM
sensor.
• If motor unit doesn’t operate, motor unit is overheated. Wait 30 minutes and retry. If
motor unit still will not operate replace logic board.
Symptom: Door reverses while closing.
• Check for possible door obstructions and remove.
• Check that the cable tension monitor is properly connected to the operator.
• Replace the cable tension monitor.
27
PROGRAMMING
NOTICE: If this SAFETY SIGNAL garage door opener is operated with a non-rolling code transmitter, the technical measure in
the receiver of the garage door opener, which provides security against code-theft devices, will be circumvented. The owner of
the copyright in the garage door opener does not authorize the purchaser or supplier of the non-rolling code transmitter to
circumvent that technical measure.
TM
Your garage door opener has already been programmed at the factory to operate with your hand-held remote control. The door
will open and close when you press the large push button.
Below are instructions for programming your opener to operate with additional SAFETY SIGNAL remote controls.
TM
To Add or Reprogram a Hand-held Remote Control
USING THE “LEARN” BUTTON
USING THE SMART CONTROL PANEL™
LOCK
LOCK LIG
HT
LIGHT
LOCK
LOCK
LIGH
LIG
T HT
1. Press and release the purple “learn”
button on the motor unit. The learn
indicator light will glow steadily for 30
seconds.
1. Press the Prog <Learn> button on the
Smart Control Panel™.
LIGHT
LOCK
2. Press the Prog <Learn> button again
to confirm Learn Mode.
2. Within 30 seconds, press and hold the
button on the hand-held remote* that
you wish to operate your garage door.
LIGHT
LOCK
3. Press the button on the hand-held
remote that you wish to operate your
garage door.
3. Release the button when the motor
unit lights blink. It has learned the
code. If light bulbs are not installed,
two clicks will be heard.
4. When the motor unit lights blink, it has
learned the code. If light bulbs are not
installed, two clicks will be heard.
To Erase All Codes From
Motor Unit Memory
*3-Button Remote
If provided with your garage door opener, the large button is
factory programmed to operate it. Additional buttons on any
To deactivate any unwanted remote, first
erase all codes:
Press and hold the “learn” button on
motor unit until the learn indicator light
goes out (approximately 6-9 seconds).
All previous codes are now erased.
Reprogram each remote or keyless
entry you wish to use.
SAFETY SIGNAL
TM
3-Button remote or
mini-remote can be
programmed to
operate other Safety
Signal™ garage door
openers.
28
To Add, Reprogram or Change a Keyless Entry PIN
NOTE: Your new Keyless Entry must be programmed to operate your garage door opener.
USING THE “LEARN” BUTTON
USING THE SMART CONTROL PANEL™
LOCK
LOCK
LIGHT
LIG
HT
NOTE: This method requires two people if the Keyless
Entry is already mounted outside the garage.
1. Press and release the purple “learn”
button on motor unit. The learn
indicator light will glow steadily for 30
seconds.
1. Press the Prog <Learn> button on the
Smart Control Panel™.
2. Within 30 seconds, enter a four digit
personal identification number (PIN)
of your choice on the keypad. Then
press and hold the ENTER button.
LIGHT
LOCK
2. Press the Prog <Learn> button again
to confirm Learn Mode.
3. Release the button when the motor
unit lights blink. It has learned the
code. If light bulbs are not installed,
two clicks will be heard.
LIGHT
LOCK
3. Enter a four digit personal
identification number (PIN) of your
choice on the keypad. Then press
enter.
To change an existing, known PIN
If the existing PIN is known, it may be changed by one
person without using a ladder.
1. Press the four buttons for the present PIN, then press and
hold the # button.
The opener light will blink twice. Release the # button.
2. Press the new 4-digit PIN you have chosen, then
press Enter.
The motor unit lights will blink once when the PIN has been
learned.
Test by pressing the new PIN, then press Enter. The door
should move.
4. When the motor unit lights blink, it has
learned the code. If light bulbs are not
installed, two clicks will be heard.
3. To set the number of hours this temporary PIN will work,
press the number of hours (up to 255), then press ✽.
OR
3. To set the number of times this temporary PIN will open
door, press the number of times (up to 255), then press #.
The opener light will blink once when the temporary PIN has
been learned.
Test by pressing the four buttons for the temporary PIN, then
press Enter. The door should move. If the temporary PIN was
set to a certain number of openings, remember that the test
has used up one opening.To clear the temporary password,
repeat steps 1-3, setting the number of hours or times to 0 in
step 3.
One Button Close: Opener can be closed by pressing only
the ENTER button if the one button close feature has been
activated. This feature has been activated at the factory. To
activate or deactivate this feature press and hold buttons 1
and 9 for 10 seconds. The keypad will blink twice when the
one button close is active. The keypad will blink four times
when one button close is deactivated.
To set a temporary PIN
You may authorize access by visitors or service people with a
temporary 4-digit PIN. After a programmed number of hours
or number of accesses, this temporary PIN expires and will
no longer open the door. It can be used to close the door
even after it has expired. To set a temporary PIN:
1. Press the four buttons for your personal entry PIN (not the
last temporary PIN), then press and hold the ✽ button.
The opener light will blink three times. Release the button.
2. Press the temporary 4-digit PIN you have chosen, then
press Enter.
The opener light will blink four times.
29
Reprogramming Light or Additional Light
Your garage door opener remote light has already been programmed at the factory to operate with your opener. Any
additional or replacement remote lights will need to be programmed.
1. Press the “learn button” on light until
LED comes ON.
2. Activate the garage door using the
hand-held remote, wall control or
keyless entry.
3. It has learned the code and the light
turns on.
30
REPAIR PARTS
Installation Parts
5
7
6
4 2
NOT
9
15
ICE
3
LOC
K
12
8
1
14
13
11
10
LIG
HT
KEY
NO.
PART
NO.
1
2
3
4
5
6
41A6319-2
373PG
10A19
10A33
29C151
41A4582
7
8
9
10
41B4494-1
41A6104
41C0902
41A5034
DESCRIPTION
Smart Control Panel™
3-Button remote control
3V2016 lithium battery: led and opener
3V2450 lithium battery: proximity switch
Remote control visor clip
Emergency release rope & handle
assembly
2-Conductor bell wire - white & white/red
Cable tension monitor
Mounting bracket
Safety sensor kit (receiving and
sending eyes) with 3' (.9 m)
2-conductor bell wire attached
KEY
NO.
PART
NO.
DESCRIPTION
11
12
13
14
15
41A6388
41A6102
41A5266-1
380LM
41D96-1
Collar with set screws (2)
Power door lock
Safety sensor brackets (2)
Remote Light (Opener Light)
Light lens for light
101D173
41A6288
41A6298
114A3521
31
NOT SHOWN
Push bar for door control
Hardware bag for light
Installation hardware bag
(includes hardware listed on page 5)
Owner’s manual
Motor Unit Assembly Parts
6
2
5
1
3
4
KEY
NO.
PART
NO.
DESCRIPTION
KEY
NO.
PART
NO.
1
41DJ001
Logic board complete with plate
4
41A6095
Motor with bracket
2
41A6408
Absolute Encoder System
5
41B122
Power cord
3
41C168
Transformer
6
41A6348-5
Cover
32
DESCRIPTION
ACCESSORIES
41A5281
377LG
902LM/903LM
395LM
380LM
975LM
373W
Designer Burled Walnut 3-Button
Remote Control with Security✚®:
Includes visor clip.
373RGD
3-Button Safety Signal™
Remote Control:
Extension Brackets:
(Optional) For safety reversing
sensor installation onto the wall
or floor.
Keyless Entry with Security✚®:
Enables homeowner to operate
garage door opener from outside
by entering a password on a
specially designed keyboard. Also
can add a temporary password for
visitors or service persons. This
temporary password can be limited
to a programmable number of
hours or entries.
Includes visor clip.
2 & 3 Door Multi-Function Wall
Control:
Ideal for homes with up to three
garage doors. Combine up to
three controls into one wall control
panel for a neat compact
appearance. Enhanced functions
include Lock Feature to lock out
outside radio signals while you are
away from home and turn opener
lights on or off from the
control panel.
370LM
3-Button Mini-Remote Control
with Security✚®:
With key ring.
378LM
Wireless Door Control:
Push bar, light feature and auxiliary
button. Includes battery.
915LM
Garage Door Monitor:
Security for the largest door of your
home!
Tells you if your garage door is open or
closed. Monitors up to 4 garage doors
by adding additional sensor modules.
CLOSED
OPEN
Remote Light Control:
Enables homeowner to turn on a
lamp, television or other appliance
from their car with their garage
door opener remote or from
anywhere in their home with an
additional LiftMaster Safety
Signal™ remote.
Remote Light:
Enables homeowner to turn on a
work light from their car with their
garage door opener remote or
from anywhere in their home with
an additional LiftMaster Safety
Signal™ remote.
916LM
Garage Door Monitor Sensor:
Additional accessory sensor for homes
with multiple garage doors.
475RGD
Standby Power Unit:
Provides backup power to the model
3800RGD garage door opener.
373PG
3-Button Security✚® Remote Control:
Includes visor clip.
Laser Park Assist:
Laser enables homeowners to
precisely park vehicles in the
garage.
480LM
Alternate Mounting Kit:
This kit allows model 3800RGD to be
mounted below the torsion bar in the
case where the torsion bar is not
round or the normal mounting area
is obstructed.
33
OPERATOR NOTES
34
OPERATOR NOTES
35
RAYNOR GARAGE DOORS
SERVICE IS ON CALL
®
OUR LARGE SERVICE ORGANIZATION
SPANS AMERICA
INSTALLATION AND SERVICE INFORMATION IS AS
NEAR AS YOUR TELEPHONE FIVE DAYS A WEEK.
SIMPLY DIAL OUR TOLL FREE NUMBER:
HOW TO ORDER
REPAIR PARTS
Selling prices will be furnished on request or parts will
be shipped at prevailing prices and you will be billed
accordingly.
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE
THE FOLLOWING INFORMATION:
1-800-472-9667
• PART NUMBER
• PART NAME
• MODEL NUMBER
ADDRESS ORDERS TO:
RAYNOR GARAGE DOORS
Technical Support Group
6050 S. Country Club Road
Tucson, Arizona 85706
®
For professional installation, parts and service,
contact your local RAYNOR GARAGE DOORS
distributor. Look for him in the Yellow Pages, or visit our
Dealer Locator on our Website www.Raynor.com.
®
SERVICE INFORMATION
TOLL FREE NUMBER:
1-800-528-9131
RAYNOR GARAGE DOOR OPENER FIVE-YEAR LIMITED WARRANTY
LIFETIME MOTOR LIMITED WARRANTY
®
RAYNOR® (“Seller”) warrants to the first retail purchaser of this product, for the residence in which this product is originally installed, that it is
free from defect in materials and/or workmanship for a period of five years from the date of purchase [and that the motor is free from defect in
materials and/or workmanship for a period of lifetime from the date of purchase]. The proper operation of this product is dependent on your
compliance with the instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions will
void this limited warranty in its entirety.
If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-9131, toll free,
before dismantling this product. Then send this product, pre-paid and insured, to our service center for warranty repair. You will be advised of
shipping instructions when you call. Please include a brief description of the problem and a dated proof-of-purchase receipt with any product
returned for warranty repair. Products returned to Seller for warranty repair, which upon receipt by Seller are confirmed to be defective and
covered by this limited warranty, will be repaired or replaced (at Seller's sole option) at no cost to you and returned pre-paid. Defective parts will
be repaired or replaced with new or factory-rebuilt parts at Seller's sole option.
ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE FIVE YEAR LIMITED
WARRANTY PERIOD SET FORTH ABOVE [EXCEPT THE IMPLIED WARRANTIES WITH RESPECT TO THE MOTOR, WHICH ARE
LIMITED IN DURATION TO THE LIFETIME LIMITED WARRANTY PERIOD FOR THE MOTOR], AND NO IMPLIED WARRANTIES WILL
EXIST OR APPLY AFTER SUCH PERIOD. Some States do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. THIS LIMITED WARRANTY DOES NOT COVER NON-DEFECT DAMAGE, DAMAGE CAUSED BY
IMPROPER INSTALLATION, OPERATION OR CARE (INCLUDING, BUT NOT LIMITED TO ABUSE, MISUSE, FAILURE TO PROVIDE
REASONABLE AND NECESSARY MAINTENANCE, UNAUTHORIZED REPAIRS OR ANY ALTERATIONS TO THIS PRODUCT), LABOR
CHARGES FOR REINSTALLING A REPAIRED OR REPLACED UNIT, REPLACEMENT OF BATTERIES AND LIGHT BULBS OR UNITS
INSTALLED FOR NON-RESIDENTIAL USE.
THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR
HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. THIS
LIMITED WARRANTY ALSO DOES NOT COVER ANY PROBLEMS CAUSED BY INTERFERENCE. ANY SERVICE CALL THAT
DETERMINES THE PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS COULD RESULT IN A FEE TO YOU.
UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES ARISING IN
CONNECTION WITH USE, OR INABILITY TO USE, THIS PRODUCT. IN NO EVENT SHALL SELLER'S LIABILITY FOR BREACH OF
WARRANTY, BREACH OF CONTRACT, NEGLIGENCE OR STRICT LIABILITY EXCEED THE COST OF THE PRODUCT COVERED
HEREBY. NO PERSON IS AUTHORIZED TO ASSUME FOR US ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS
PRODUCT.
Some states do not allow the exclusion or limitation of consequential, incidental or special damages, so the above limitation or exclusion may
not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
114A3521
© 2007, The Chamberlain Group, Inc.
All Rights Reserved
Download PDF