Rersion 1
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11. O n l y u s e a t t a c h m e n t s / a c c e s s o r i e s s p e c i f i e d b y t h e
12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged. liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. To Reduce the Risk of Fire or Electric Shock, Do not Expose
This Appliance To Rain or Moisture.
16. The Shock Hazard Marking and Associated Graphical Symbol
is provided on the bottom panel of unit.
17. Apparatus shall not be exposed to dripping or splashing and no
objects filled with liquids, shall not be placed on the apparatus.
18. Excessive sound pressure on ear- and headphones could
impair the hearing ability. Higher setting that idle on the
equalizer leads to higher signal voltages on the output for ear
and headphones.
19. The power plug should be close to the radio, and easy to be
approached that during the emergency, to disconnect the power
from the radio, just unplug the power plug from the AC power
20. Where the MAINS plug or an appliance coupler is used as the
disconnect device, the disconnected device shall remain readily
/ 50W
/ 50W
Power button
2 Band selecting rotary
3 Dial scale
4 Dial indicator
5 Dial marker
6 Volume control
7 Treble control
8 Bass control
9 Speaker
10 Tuning LED indicator
11 Tuning control
12 F-type external antenna terminal
13 AM external antenna terminal
14 Subwoofer speaker
15 AC main power switch
16 AC power cord socket
17 Dimmer control
18 Headphone socket
19 AUX IN socket
20 External / internal antenna switch
Power your radio
AC operation
Before you plug the AC cord into the radio, make sure the AC
voltage is correct. Insert the plug on the end of the supplied power
cord into the AC power socket on the back of the radio and turn on
the main power switch.
Antenna setup for FM reception
The radio comes with built-in AM/FM antenna and external
To use FM internal antenna, make sure to switch FM external/
internal antenna switch in the back of your radio to internal antenna
position (i.e. INT. FM ANTENNA). As for external antenna, you
can use to improve FM reception. Two types of antenna can be
used. You can connect the supplied FM wire antenna to the F-type
antenna terminal and adjust the wire for best reception.
You can also connect a 75 ohm coaxial cable of outdoor antenna
to the terminal. Make sure to switch external/internal antenna
switch to external position while using the supplied wire antenna
or connecting the outdoor antenna. In some of the European
countries, you may have to connect the supplied antenna terminal
adaptor to connect with the outdoor antenna.
Operating your radio FM
1. Make sure you have set up the FM antenna in advance and turn
on the main power switch in the rear of the unit.
2. Press the power button located in the front panel.
3. Rotate the band selecting rotary to the FM (MONO) or ST(FM
Note: If the FM radio station being listened to has a weak signal,
some hiss may be audible. It is possible to reduce this hiss by
forcing the radio to play the station in mono rather than stereo.
4. Rotate the Tuning Control to select the desired station. In FM
mode, the tuning scale is marked in MHz (Megahertz). The tuning
LED indicator will appear brightest when best tuning has been
achieved. In ST mode, the ST tuning LED indicator will illuminate
when a stereo station is tuned.
5. Adjust the Volume Control for comfortable listening.
6. Press the power button to turn off the radio.
Antenna setup for AM reception
The radio comes with built-in AM antenna which should be enough
for normal listening. To improve the AM reception, you may connect
the outdoor AM antenna with AM external antenna terminal.
Operating your radio AM
1. Press the power button located in the front panel.
2. Rotate the Tuning Control to select the desired station. In AM
mode, the tuning scale is marked in kHz (Kilohertz). The tuning
LED will appear brightest when best tuning has been achieved.
3. Rotate your radio for best reception.
4. Adjust the Volume Control for comfortable listening.
5. Press the power button to turn off the radio.
Dial marker
This device allows you to mark 3 of your favorite station frequency,
so that you can find the particular station immediately next time
when tuning the stations.
Headphone use
Headphone use with this radio should be fitted with a 3.5 mm jack
plug. Insert the headphones plug into the socket marked on the
rear side of the radio. When the headphones are plugged in, the
loudspeaker is automatically disconnected.
AUX IN socket
Connect a stereo or mono audio source (like CD walkman, iPod or
digital media music player) to this input to listen the audio program
via the speaker.
Dimmer control
The brightness of the dial scale may be adjusted. If you use the
unit in the bedroom, you may prefer a higher brightness level than
the standard setting.
Treble / Bass control
The sound on your radio can be adjusted to suit your personal taste
for the material that you are listening to. You can set the treble and
bass levels to your own preferences.
Note: To adjust the volume without physical interference, you can
press down the treble and bass button. It will not change your
treble/ bass setting.
AC Power:
AC 120V/ 60 Hz/ 50W (max) (US version)
AC 230V/ 50 Hz/ 50 W (max) (European version)
Frequency Coverage:
FM 87.50 - 108 MHz
AM 520 - 1710 kHz
3.5mm diameter, stereo
Internal Antenna System:
AM Built-in ferrite aerial
FM Built-in wiring aerial
External antenna terminal:
AM antenna terminal
FM F-type antenna terminal
Output Power:
3W+3W stereo amplifier (1 kHz)
10W subwoofer amplifier (100Hz)
Stereo: 2.25inches 8 ohm x 2
Subwoofer: 3.5inches 8 ohm x 1
Headphones socket:
3.5 mm dia. Stereo jack Stereo output
Output power: 3mW + 3mW (impedance 32ohm)
If at any time in the future you should need to dispose of this
product please note that: Waste electrical products should not be
disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
(Waste Electrical and Electronic Equipment Directive)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF