BDP | 584B | User manual | BDP 584B User manual

19" BLU-RAY DISC PLAYER
BDP-620
BLU-RAY DISC PLAYER BDP-620
USER MANUAL
Table of Contents
English
Table of Contents............................................ 2
Warning............................................................ 3
Safety................................................................ 3
Notes About the Discs.................................... 4
Precautions...................................................... 4
Important Safety ............................................ 5
Instructions ..................................................... 5
FCC Statement................................................. 5
Basic Information............................................ 6
About this manual......................................... 6
This Player Can Play the Following Discs and
Files.............................................................. 6
Supported Disc formats............................. 6
Supported codec formats........................... 6
Supported file formats................................ 6
Notes about BD-ROM compatibility........... 6
BD/DVD region code..................................... 7
Note on playback operations of BDs/ DVDs. 7
Copyrights..................................................... 7
Examples of discs that the player cannot play
...................................................................... 7
Product Overview............................................ 8
Front Panel................................................... 8
Front Panel Display....................................... 8
2.0 Rear Panel.............................................. 8
Control Via RS232 (optional).......................... 9
Guide to the Remote Control.......................... 10
Guide to the Remote Control Continue......... 11
Main features................................................... 12
Getting started................................................. 12
Step 1: Unpackaging..................................... 12
Step 2: Mounting the 19 inch brackets.......... 12
Step 3: Connecting the Video Cords/HDMI
Cord.............................................................. 12
Step 4: Connecting the Audio Cords............. 14
Step 5: Connecting to Network..................... 14
Step 6: Connecting the Mains Lead.............. 14
Step 7: Preparing the Remote...................... 15
Step 8: Easy Setup Wizard........................... 15
Home Menu Operation.................................... 16
Using the Home Menu..................................... 16
General Setting............................................. 16
Display Setting.............................................. 18
Audio Setting................................................. 18
System Information....................................... 19
Basic Operations............................................. 19
Playing a Disc............................................... 19
On screen Display Menu............................... 19
Playing video files...................................... 19
Playing image files..................................... 20
Playing audio files...................................... 20
Checking the Disc Information...................... 20
Example: when playing a BD-ROM.............. 20
Using Media Center ....................................... 21
Introduction................................................... 21
Supported Functions..................................... 21
Operation Steps............................................ 21
1. Selecting playback source .................... 21
2. Selecting Media for Playback................. 21
3. Playing Photo/Audio/Video Files............ 21
Troubleshooting.............................................. 22
Picture........................................................... 22
Sound............................................................ 22
Operation...................................................... 22
Specification.................................................... 23
GB-2
• To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
• To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
• Batteries or batteries installed apparatus shall
not be exposed to excessive heat such as
sunshine, fire.
CAUTION
The use of optical instruments with this product will
increase eye hazard. As the laser beam used in
this Blu-ray Disc player is harmful to eyes, do not
attempt to disassemble the cabinet.
Refer servicing to qualified personnel only.
This appliance is classified as a CLASS 1 LASER
product. The CLASS 1 LASER PRODUCT
MARKING is located on the laser protective
housing inside the enclosure.
Disposal of Old Electrical & Electronic
Equipment (Applicable in the European
Union and other European countries with
separate collection systems)
This symbol on the product or on its
packaging indicates that this product
shall not be treated as household waste.
Instead it shall be handed over to the applicable
collection point for the recycling of electrical and
electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and
human health, which could otherwise be caused by
inappropriate waste handling of this product. The
recycling of materials will help to conserve natural
resources. For more detailed information about
recycling of this product, please contact your local
Civic Office, your household waste disposal service
or the shop where you purchased the product.
The above symbol is applicable in the European
Union and other European countries with separate
collection systems.
Disposal of waste batteries
(applicable in the European Union and
other European countries with separate
collection systems)
This symbol on the battery or on the
packaging indicates that the battery
provided with this product shall not be
treated as household waste.
By ensuring these batteries are disposed of
correctly, you will help prevent potentially negative
consequences for the environment and human
health which could otherwise be caused by
inappropriate waste handling of the battery. The
recycling of the materials will help to conserve
natural resources.
In case of products that for safety, performance
or data integrity reasons require a permanent
connection with an incorporated battery, this battery
should be replaced by qualified service staff only.
To ensure that the battery will be treated properly,
hand over the product at end-of-life to the
applicable collection point for the recycling of
electrical and electronic equipment.
For all other batteries, please view the section on
how to remove the battery from the product safely.
Hand the battery over to the applicable collection
point for the recycling of waste batteries.
For more detailed information about recycling of
this product or battery, please contact your local
Civic Office, your household waste disposal service
or the shop where you purchased the product.
Safety
• This unit operates on 100 – 240 V AC, 50/60
Hz. Check that the unit’s operating voltage is
identical with your local power supply.
• To prevent fire or shock hazard, do not place
objects filled with liquids, such as vases, on the
apparatus.
Installing
• Do not install the unit in an inclined position. It is
designed to be operated in a horizontal position only.
• Keep the unit and discs away from equipment
with strong magnets, such as microwave ovens,
or large loudspeakers.
• Do not place heavy objects on the unit.
• Do not install this unit in a confined space, such
as a bookshelf or similar unit.
• Install this system so that the mains lead can be
unplugged from the wall socket immediately in
the event of trouble.
• The USB terminal shall be loaded with 0.5A
under normal operation.
GB-3
English
Warning
Notes About the Discs
• To keep the disc clean, handle the disc by
its edge. Do not touch the surface. Dust,
fingerprints, or scratches on the disc may cause
it to malfunction.
English
On operation
• If the player is brought directly from a cold to
a warm location, or is placed in a very damp
room, moisture may condense on the lenses
inside the player. Should this occur, the player
may not operate properly. In this case, remove
the disc and leave the player turned on for about
half an hour until the moisture evaporates.
• When you move the player, take out any discs.
If you don’t, the disc may be damaged.
• Do not expose the disc to direct sunlight or heat
sources such as hot air ducts, or leave it in a
car parked in direct sunlight as the temperature
may rise considerably inside the car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth. Wipe the
disc from the centre out.
• Do not use solvents such as benzine, thinner,
commercially available disc/ lens cleaners, or
anti-static spray intended for vinyl LPs.
• If you have printed the disc’s label, dry the label
before playing.
Precautions
On safety
Should any solid object or liquid fall into the
cabinet, unplug the player and have it checked by
qualified personnel before operating it any further.
On power sources
• The player is not disconnected from the AC
power source (mains) as long as it is connected
to the wall outlet, even if the player itself has
been turned off.
• If you are not going to use the player for a long
time, be sure to disconnect the player from the
wall outlet. To disconnect the AC power cord
(mains lead), grasp the plug itself; never pull the
cord.
On placement
• Place the player in a location with adequate
ventilation to prevent heat build-up in the player.
• Do not place the player on a soft surface such
as a rug that might block the ventilation holes.
• Do not place the player in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust, or mechanical shock.
On adjusting volume
Do not turn up the volume while listening to a
section with very low level inputs or no audio
signals. If you do, the speakers may be damaged
when a peak level section is played.
On cleaning
Clean the cabinet, panel, and controls with a soft
cloth slightly moistened with a mild detergent
solution. Do not use any type of abrasive pad,
scouring powder or solvent such as alcohol or
benzine.
On cleaning discs, disc/lens cleaners
Do not use cleaning discs or disc/lens cleaners
(including wet or spray types). These may cause
the apparatus to malfunction.
On replacement of parts
In the events that this player is repaired, repaired
parts may be collected for reuse or recycling
purposes.
IMPORTANT NOTICE
Caution: This player is capable of holding a
still video image or on-screen display image
on your television screen indefinitely. If you
leave the still video image or on-screen
display image displayed on your TV for an
extended period of time you risk permanent
damage to your television screen. Plasma
display panel televisions and projection
televisions are susceptible to this.
If you have any questions or problems concerning
your player, please consult your dealer.
GB-4
1. Read these instructions and keep it for future
reference.
2. Heed all warnings.
3. Follow all instructions.
4. Do not use this apparatus near water.
5. Clean only with dry cloth.
6. Do not block any ventilation openings.
Install in accordance with the manufacture’s
instructions.
7. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
8. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
9. Only use attachments/accessories specified
by the manufacturer.
10.Use only with the cart, stand, tripod, bracket,
or table specified by the manufacture,
or sold with the apparatus. When a
cart is used, use caution when moving
the cart/apparatus combination to
avoid injury from tip-over.
11.Unplug this apparatus during lightening storms
or when unused for long periods of time.
12.Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
13.The apparatus shall not be exposed to
dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on
the apparatus.
14.The mains plug or an appliance coupler is
used as disconnect device, the disconnect
device shall remain readily operable.
15.Do not use this apparatus in the box or in the
cabinet, it should be placed on a ventilation
area.
16.Warning: To reduce the risk of electric shock,
do not remove the cover or back, do not
expose this apparatus to rain or moisture.
There are no user- serviceable parts inside.
Refer servicing to qualified service personnel.
Caution:
To prevent electric shock, match the wide blade
on the power cord plug to the wide slot on an
electric outlet. If the plug does not fit, consult a
licensed electrician to replace the obsolete outlet.
Do not modify the power cord plug, or you will
defeat this safety feature.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates that dangerous
voltage constituting a risk of electric
shock is present within your Blu-ray Disc
Player. This label is located on the back
of your Blu-ray Disc Player.
This symbol indicates that there are
important operating and maintenance
instructions in the literature
accompanying your Blu-ray Disc Player.
This mark is applied to show the equipment
conforms to European safety and electromagnetic compatibility standards.
FCC Statement
This device complies with Part 15 FCC Rules.
Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference
received including interference that may cause
undesired operation.
2. *Federal Communications Commission (FCC)
statement
This Equipment has been tested and found
to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC rules.
These Limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions may cause harmful interference
to radio communications .However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on , the user is encouraged to
try to correct the interference by one or more of
the following measures :
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
GB-5
English
Important Safety
Instructions
Basic Information
About this manual
Instructions in this manual describe the controls on the remote. You can also use the controls on the
player if they have the same or similar names as those on the remote. The meanings of the icons used
in this manual are described as below:
English
Icon
BD
DVD
DATA DVD
CD
Meaning
Functions available for BD-ROMs and BD-REs/BD-Rs*1, including DL discs.
Functions available for DVD VIDEOs and DVD+RWs/DVD+Rs in +VR mode or
DVD-RWs/DVD-Rs in video mode,including 8 cm discs.
Functions available for DATA DVDs (DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs
containing MPEG-2 movie files, and JPEG image files).
Functions available for music CDs or CD-Rs/CD-RWs in music CD Format.
*1 BD-REs/BD-Rs in BDMV mode only.
Notes: The menu screen/OSD illustration used in this manual may not match the graphics displayed
on your TV screen, please make the actual display as standard.
DTS statement:
2.0 ch
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S. and
worldwide patents issued & pending. DTS, the Symbol, & DTS and the Symbol together are registered
trademarks & DTS 2.0+Digital Out is a trademark of DTS, Inc. Product includes software. © DTS, Inc.
All Rights Reserved.
Manufactured under license from Dolby laboratories. Dolby and the double-D symbol are trademarks
of Dolby Laboratories.
This Player Can Play the Following Discs and Files
Supported Disc formats
Name
BD
DVD
CD
Meaning
BDMV,BDAV,BD-ROM, BD-R/RE
DVD-Video,DVD-VR,DVD+VR,DVD-ROM,DVD-R/+R,-RW/+RW,DL
CD-DA,CD+G,DTS-CD,VCD,SVCD,Kodak Picture CD,CD-R/RW
Supported codec formats
H.264,VC-1,MPEG-1/2/4,XviD,DTSMA,DTSHR,DTS Digital Surround,Dolby TrueHD,Dolby Digital
Plus,Dolby Digital,MP3,LPCM,JPEG
Supported file formats
MP4, MP3, TS/TP, AVI, M2TS, VOB, FLV, MPG,JPG
Notes about BD-ROM compatibility
This player supports BD-ROM Profile 2.0 only. Playback of later versions and BDs other than BD-ROM
is not guaranteed. Since the Blu-ray Disc specifications are new and evolving, some discs may not
play depending on the disc type and the version.
The audio output differs depending on the source, connected output jack, and selected audio settings.
GB-6
BD/DVD region code
Your player has a region code printed on the back of the unit and only will play BD-ROM/DVD VIDEOs
(playback only) labeled with identical region codes. This system is used to protect copyrights.
Note on playback operations of BDs/ DVDs
Some playback operations of BDs/DVDs may be intentionally set by software producers. Since
this player plays BDs/DVDs according to the disc contents the software producers designed, some
playback features may not be available. Also, refer to the instructions supplied with the BDs/DVDs.
Copyrights
This item incorporates copyright protection technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright protection technology must be authorized by Rovi
Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized
by Rovi Corporation. Reverse engineering or disassembly is prohibited.
Examples of discs that the player cannot play
The player cannot play the following discs:
• BDs with cartridge.
• DVD-RWs/DVD-Rs of VR mode.
• DVD-RAMs.
• HD DVDs.
• DVD Audio discs.
• DATA CDs (CD-Rs/CD-RWs other than music CD format).
• CD-ROMs recorded in PHOTO CDs format.
• Data part of CD-Extras.
• HD layer on Super Audio CDs.
Also, the player cannot play the following discs:
• A BD-ROM/DVD VIDEO with a different region code.
• A disc that has a non-standard shape (e.g., card, heart).
• A disc with paper or stickers on the playback side.
• A disc that has the adhesive of cellophane tape or a sticker still left on it.
Notes:
1 Notes about BD-REs/BD-Rs, DVD+RWs/ DVD+Rs, DVD-RWs/ DVD-Rs, or CD-Rs/CD-RWs
Some BD-REs/ BD-Rs, DVD+RWs/ DVD+Rs, DVD-RWs/ DVD-Rs, or CD-Rs/ CD-RWs cannot be
played on this player due to the recording quality or physical condition of the disc, or the characteristics
of the recording device and authoring software. The DVD disc will not play if it has not been correctly
finalized. For more information, refer to the operating instructions for the recording device. Note
that some playback functions may not work with some DVD+RWs/DVD+Rs, even if they have been
correctly finalized. In this case, view the disc by normal playback.
2 Music discs encoded with copyright protection technologies
This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently,
various music discs encoded with copyright protection technologies are being marketed by some
record companies. Please be aware that among those discs, there are some that do not conform to
the CD standard and may not be playable by this product.
3 Note on Dual-Discs
A Dual-Disc is a two sided disc product which mates DVD recorded material on one side with digital
audio material on the other side. However, since the audio material side does not conform to the
Compact Disc (CD) standard, playback on this product is not guaranteed.
4 Note about double-layer DVDs
The playback pictures and sound may be momentarily interrupted when the layers switch.
5 Note about 8 cm BD-REs/8 cm BD-Rs
Some 8 cm BD-REs/8 cm BD-Rs cannot be played on this player.
GB-7
English
DVD VIDEOs labeled
will also play on this player. Depending on the BD-ROM/DVD VIDEO, there
may be no region code indication, even though playing the BD-ROM/DVD VIDEO is prohibited by area
restrictions.
Product Overview
Front Panel
1
2
3
4
5
6
7
English
BLU-RAY DISC PLAYER BDP-620
1
-
2
3
4
-
IR Receiver
Receive signals from the remote control.
Front Panel Display
Disc Tray
(Open/Close)
Open/Close the disc tray.
5
Play&Pause
- Start or Pause playback.
6
(Standby)
- Turns on the player, or sets to standby mode.
7 USB Port
Note: The buttons of 4 , 5 , 6 will show after power on.
Front Panel Display
The playback information is displayed as follows.
Example: When playing a DVD VIDEO or a
BD-ROM.
Current title
Elapsed time
2.0 Rear Panel
1
1
2
3
4
2
3
4
5
6
7
8
Optional RS232 Control Port
USB Port
LAN Port
HDMI OUT jack
5
6
7
8
GB-8
AUDIO OUT L&R jacks
VIDEO OUT
OPTICAL jack
AC IN terminal
Control Via RS232 (optional)
If you have chosen for the RS232 option, third party equipment can be programmed to
send ASC11 coded commands to the BDP-620, similar to the functions on the remote
control. (settings at 9600 bps. N,8,1).
•
•
•
•
•
English
Protocol:
First byte: I
Second Byte : C
When powered on, the unit will send the following string:
Interstate Audio Rs232 link V1.1
When the code is recieved correctly it will be excecuted and “ack” will be send back.
When the code is wrong “nack” will be send back.
ICZZ is the code for a hard reset.
Example: IC20 = STOP
Code:
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
Function:
0
1
2
3
4
5
6
7
8
9
RED
GREEN
YELLOW
BLUE
FR
FF
PREV
NEXT
PLAY
SLOW
STOP
PIP
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
MEDITR
ANGLE
SUB
LEFT
DOWN
UP
ENTER
HOME
RETURN
MENU
TOPMEN
CLEAR
GOTO
REPEAT
A-B
INFO
HDMI
SPKOFF
OPEN
PWR
42
RIGHT
GB-9
Guide to the Remote Control
The following covers all of the remote’s functions. Refer to the list when necessary.
(OPEN/CLOSE): Open/close the disc tray.
(POWER): Turn on, or set the player to
standby mode.
2
MUTE
- Press to silence and press it again to resume.
3 REPEAT
Once playback begins, Press REPEAT key on the
remote control to cycle through the various repeat
modes:
-Press repeat until (REPEAT FILE) appears to
‘loop’ the current file.
-Press repeat until (REPEAT All) to ‘loop’ all the
videos selected.
-Press repeat until (REPEAT OFF) to stop the
repeat function.
A-B
When a disc is playing, pressing this button once
will save a “start point” for repeating playback.
Pressing this button again will save an “end point”
for repeating playback. Playback will repeat from
the start point to the end point.
To stop playback from repeating, the REPEAT
button should be pressed until “Repeat: OFF” is
shown on the TV.
Note:[Repeat] & [A-B] may be not available on
some disc due to itself configuration or
because the disc itself can not support the
two features. User can contact the disc
suppliers to acquire the info.
4 Number buttons
-Enter the title/chapter number, etc.
5 HOME
-Invoke the setup menu of the BD player.
6 Menu Navigation Keys
-These keys are used when navigating the
menus on BD and DVDs. They are also used for
navigating the setup menus for the BD player.
7 MEDIA CENTER
-Press to select the playback source. Please
refer to “Using Media Center”.
ANGLE
-Press Angle button during playback to display
the OSD menu, please refer to the On Screen
Display.
AUDIO
-Select the sound track or the language track on
a BD/DVD.
1
1
English
2
3
4
5
6
7
*1 When playing MPEG-2 movie files or music
files on a DATA DVD, or a music CD, you cannot
use this button.
SUBTITLE
-Select the subtitle language on a BD/DVD.
GB-10
Guide to the Remote Control Continue
21
20
19
18
17
16
15
8
14
9
13
10
12
11
8 SLOW
-Play in slow motion or stop motion. To return to
normal play, press ENTER.
9 PLAY/PAUSE
-Press to start or pause playback.
10
/
(scan)*
-Scan backward or forward. The speed changes
when pressed repeatedly.
*Depending on the disc or file type, the function
may not work or the scan speeds may differ.
11 Color buttons (RED/GREEN/YELLOW/BLUE)
-Short cut keys for selecting items on some BD’s
menus.
12
/
(previous/next)*
-Skip to the previous/next chapter, track, or file.
13 PIP
-Press to view the video in PIP mode.
Note:Work only when playing BD disc with BONUS
view feature.
14 STOP
-Press to stop playback of a BD/DVD movie or
CD audio track.
15 ENTER
-Enter the selected item.
16 RETURN
-When navigating files on a data CD or USB stick,
pressing this button to return the previous folder
or menu.
17 MENU
-Press to stop playback immediately, and bring
up the main, or ‘top’ menu of the BD or DVD
disk.
18 TOP MENU
-Press to go to ‘top’ menu of the BD or DVD disk.
19 CLEAR
-When entering numeric values via the numeric
keypad, this button is used to clear a number
entered incorrectly.
20 GOTO
-This button is used with the numeric keypad to
jump to a specific track on an audio CD.
21 INFO
-Press to show the information of title number,
chapter number, and elapsed time for BD and
DVD playback.
HDMI
-Press to switch the output resolution.
-If your TV can not output high definition videos,
press HDMI button to automatically switch the
resolution until it can display high definition videos.
GB-11
English
The following covers all of the remote’s functions. Refer to the list when necessary.
Main features
English
• Support 2D discs playback, BonusView
functions and BD-Live features.
• HDMI 1080p output with a frame rate of 24
frames per seconds (need your TV support).
• Supported file formats:
MP4, MP3, TS/TP, AVI, M2TS, VOB, FLV,
MPG,JPG
• Support codec formats:
H.264, VC-1, MPEG-1/2/4, XviD, DTSMA,
DTSHR, DTS Digital Surround, Dolby
TrueHD,Dolby Digital Plus, Dolby Digital, MP3,
LPCM, JPEG
• Support playgback of most of network videos,
we have the final interpretaion about this.
• Support playback of large files (file size >
4GB), blu-ray discs and REMUX files.
Step 3:Connecting the Video
Cords/HDMI Cord
Connect this player to your TV monitor, projector
or AV amplifier (receiver) using a video cord.
Select one of the patterns A through B ,
according to the input jack on your TV monitor,
projector or AV amplifier (receiver). In order to
view 1080p progressive signals with a compatible
TV, projector, or monitor with an HDMI input jack,
you must select pattern B .
A Connecting to a video input jack
Connect the supplied video cord (yellow) to the
yellow (video) jack. You will enjoy standard quality
images.
yellow
Video cord (supplied)
Getting started
VIDEO
L
AUDIO
yellow
R
Step 1: Unpackaging
Please make sure you have the following items in
your package:
• Blu-ray player (1)
• AV cable (1)
• Remote control (1)
• AAA batteries (2)
• User manual (1)
• 19 inch brackets(2) and mounting screws(4)
Step 2: Mounting the 19 inch
brackets
INPUT
• Use a matching "Phillips screwdriver" to
remove the 2 screws that hold the cover on the
Left and Left rear side.
• Now attach this bracket using the longer
screws as supplied.
• Repeat the same steps to attach the right
bracket.
TV, Projector, or
Amplifier(Receiver)
Rear panel of Blu-ray disc player
When connecting to a standard 4:3 screen TV
Depending on the disc, the image may not fit your
TV screen.
Note: Do not connect a VCR, etc., between your
TV and the player. If you pass the player
signals via the VCR, you may not receive
a clear image on the TV screen. If your
TV has only one audio/video input jack,
connect the player to this jack.
VCR
Blu-ray Disc Player
GB-12
Connect directly
TV
• Be sure to disconnect the HDMI cord when
moving the player.
Rear panel of Blu-ray disc player
To HDMI OUT
TV, Projector, or
Amplifier(Receiver)
HDMI cord(Not supplied)
This Blu-ray Disc player incorporates HighDefinition Multimedia Interface (HDMI™)
technology. HDMI, the HDMI logo and HighDefinition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
NOTE
If your TV video resolution has been set too high,
the screen will turn black, so you need to use
the HDMI button on Remote control to switch a
suitable output value of the TV.
• If you place the player on the cabinet with the
HDMI cord connected, do not apply too much
pressure to the cabinet wall. It may damage the
HDMI OUT jack or the HDMI cord.
• When connecting or disconnecting, do not
screw in or rotate the HDMI connector.
Notes:
1 Users should note that not all high definition
television sets are fully compatible with this
product and may cause artifacts to be displayed
in the picture. In the case of 480i/ 480p/ 576p/
720p/ 1080i/1080p scan picture problems it is
recommended that the user switch the connection
to the ‘HDMI Auto’ output. If there are questions
regarding our TV set compatibility with this model
480i/480p/576p/720p/1080i/1080p Blu-ray Disc
player.
2 Be sure to use only an HDMI cord that bears
the HDMI logo.
Notes on connecting to the HDMI OUT jack
Observe the following as improper handling may
damage the HDMI OUT jack and the connector.
• Carefully align the HDMI OUT jack on the
back of the player and the HDMI connector
by checking their shapes. Make sure the
connector is not upside down or titlted.
GB-13
English
B Connecting to an HDMI input jack
Use a certified HDMI cord (not supplied) to enjoy
high quality digital pictures and sound through
the HDMI OUT jack. You will enjoy higher quality
pictures from 480p/576p/1080i, or 1080p (highest
among the player output), if your TV, projector or
AV amplifier (receiver) is compatible.
Step 4:Connecting the Audio Step 5: Connecting to Network
Cords
• Connect your blu-ray player to the network
A Connecting to a stereo amplifier
(receiver) with a optical input jack (only
for the products with a optical input jack)
English
Connect one end of a coaxial cable (not supplied)
to the OPTICAL jack on your blu-ray player, and
connect the other end to the OPTICAL input jack
on the amplifier (receiver).*
to enjoy software updates and BD-live bonus
content.
• Connect one end of the network cable (not
supplied) to the LAN jack of your blu-ray
player, and connect the other end to the
broadband modem or router.
Rear panel of Blu-ray disc player
Rear panel of Blu-ray disc player
Mode m or R outer
LAN
To OPTICAL
OUTPUT
To OPTICAL
INPUT
To LAN port
Optical cable (not supplied)
To the network
on Modem or Router
Network cable (not supplied)
B Connecting to an amplifier (receiver)
with an HDMI input jack
Connect one end of the HDMI cable (not supplied)
to your blu-ray player, and connect the other end
to the AV amplifier (receiver).
Rear panel of Blu-ray disc player
Step 6:Connecting the Mains
Lead
After all of the other connections are complete,
connect the supplied mains lead to the AC IN
terminal of the player. Then plug the player and
TV mains lead (power cords) into the mains.
To Mains lead
To HDMI OUT
Amplifier(Receiver)
To AC IN
Rear panel of Blu-ray disc player
HDMI cord(Not supplied)
Note:Not all HDMI-compatible AV amplifiers
(receivers) accept 8ch Linear PCM signals.
See also the operating instructions supplied
with the connected AV amplifier (receiver).
GB-14
Step 8: Easy Setup Wizard
1. You can control the player using the supplied
remote. Insert two R03 (size AAA) batteries by
matching the+ and - ends on the batteries to
the markings inside the battery compartment.
When using the remote, point it at the remote
sensor on the player.
When turning on the Blu-ray player for the first
time, Easy Setup Wizard is displayed on screen.
Follow the wizard to configure the basic settings
of your Blu-ray player.
Warning: The battery pack or batteries installed
shall not be exposed to excessive heat
such as sunshine,Fire or the like .
Note:
• Do not leave the remote in an extremely hot or
humid place.
• Do not drop any foreign object into the
remote casing, particularly when replacing the
batteries.
• Do not expose the remote sensor to direct
sunlight or a lighting apparatus. Doing so may
cause a malfunction.
• If you do not use the remote for an extended
period of time, remove the batteries to avoid
possible damage from battery leakage and
corrosion.
2. When using the Remote control, please point
the Remote Sensor directly and operate it within
10 meters. Or use it within 60o in 8 meters.
1. Welcome screen
Press “Enter” to continue.
2. Press Up/Down direction button to select the
OSD language, then press “Enter” button to
confirm.
3. Choosing the resolution
- Use the Up/Down direction to select the
resolution that is supported by your TV.
Auto: The player will choose the best resolution
for your TV automatically.
- Press “Enter” key to confirm your selection
and get to the next step.
4. Select the aspect ratio
- Press Up/Down direction button to select the
aspect ratio.
- Please refer to “TV Screen” for details.
5. Press “Enter” to complete setup
Note: You can select Home Menu>General
Setting>Easy Setup to enter Easy setup Wizard.
BLU-RAY DISC PLAYER BDP-620
30o 30o
GB-15
English
Step 7: Preparing the Remote
Home Menu Operation
Using the Home Menu
Press HOME button to display the Home Menu.
English
Home Menu Screen
General Setting: System, Language, Playback,
Security, Network.
Display Setting: TV, Video Process, Motion
Video Process.
Audio Setting: Audio Output, Speaker Setting
System Information: Software Version, MAC
address.
Use direction buttons to select and press Enter to
confirm, press HOME again to exit.
Note: Some settings are only available in stop
mode.
General Setting
Upgrade
Avaliable upgrade methods: Disc, USB flash
drive, Network.
• If “Disc Auto Upgrade” is set to off, you can
upgrade via disc manually.
Please follow the steps below to upgrade manually:
1. Load the disc/USB flash drive that contains
upgrade file, then select the corresponding
upgrade method.
2. Search for the upgrade file in the disc/USB
flash drive, it will take some time.
3. Press “Enter” to start the upgrade.
4. It will take some time for upgrading. The player
will reset automatically and go into “Easy Setup
Wizard” screen after upgrading.
Notes:
1. If the upgrade file doesn’t pass the validation,
an error message will appear.
2. Make sure the the version of upgrade file is
higher than the current version.
3. Make sure the firmware version in “System
Information” is updated after upgrading.
4. When you use the USB storage for upgrading,
If your player has two USB ports, you can
only use the USB port in the rear panel for
upgrading.
Easy Setup
Reset basic settings, the Easy Setup Wizard
(Initial setup wizard) will appear.
BUDA
View BUDA information.
System
Language Setting
Screen Saver
Turn on/off Screen Saver function.
If the Screen Saver is set to ON, the player
will enter Screen Saver mode after 5 minutes
if there is no operation for 5 minutes, it will go
into standby mode if there is no operation for 30
minutes.
OSD
Set the OSD (on screen display) language.
HDMI CEC
Turn on/off HDMI CEC function.
Note: This function is only available when your
TV supports it.
Subtitle
Set the subtitle display language.
Note: Not all the supported languages of the
player are available on all discs. Some
discs may not allow the audio language to
be set on the settings menu of the player.
In this case, select the audio language from
the menu of the disc.
Disc Auto Upgrade
Turn on/off “Disc Auto Upgrade” function.
For more information about “Disc Auto Upgrade”,
please refer to “Upgrade”.
Menu
Set the menu language.
Audio
Set the audio output language.
Load Default
Reset the settings of the player to their factory
default settings.
1. Select “Load Default” then press “Enter” to
confirm.
2. It will take some time to load the default
settings.
GB-16
Closed Caption
Turn on/off the closed caption function.
Angle Mark
Turn on/off Angle Mark.
Some BD/DVD-Video discs contain scenes
recorded at different camera angles and allow
the user to view video play from different camera
angles. When this option is set to ON, the Bluray disc player will identify if the disc is recorded
with multi angle automatically and notify you by
displaying this icon.
PIP Mark
Turn on/off PIP (picture in picture) Mark.
Some BD discs support PIP function which
allow to play primary and secondary video
simultaneously. Generally, the primaryvideo will
be displayed in full screen mode, the secondary
video will be displayed in window mode.
When this option is set to ON, the Blu-ray player
will identify if the disc supports PIP function
automatically and notify you by displaying this
icon.
Second Audio Mark
Turn on/off Second Audio mark.
Some BD discs allow the player to output primary
audio and secondary audio simultaneously.
When this option is set to ON, your player will
identify if the disc supports secondary audio
output automatically and notify you by displaying
this icon.
Last Memory
If the Last Memory function is set to ON, playback
will start from the point at which the last playback
is stopped.
PBC
Turn on/off PBC function (for VCD only).
VCD 2.0 has a PBC menu that can provide user
interactive function.
ON: The disc will can enter PBC menu of VCD
2.0 automatically when starting playback. Use
number buttons to browse the options.
OFF: Disable the PBC function of VCD 2.0.
Security
Change Password
Use this option to set or change the parental
password.
When you want to change the parental password
or play a disc with a higher rating level than the
current setting level, a dialog box will appear and
prompt you to input 4-digita password.
1. Use number buttons to input the old password.
2. Input new password.
3. Input the new password again to confirm.
Note: The default initial password is 0000.
Parental Control
This option allows the user to select a rating level
to restrict the play of discs to children, you will be
prompted to enter the default password before
being allowed to change this setting. Available
rating level are: KID SAFE, G, PG, PG13, PGR, R,
NC17 and ADULT.
Note: The default initial password is 0000.
Country Code
Use this option to select the country code, you will
be prompted to enter the default password before
being allowed to change this setting, select the
country in which you are located.
Note: The default initial password is 0000.
Network
Internet Connection
Use this option to enable/disable Internet
connection.
Interface
Use this option to select the network interface.
Information
Use this option to view the network information,
including IP address, DNS etc..
Connection Test
Use this option to check the network interface
card connection status and ping the IP address of
the default gateway to verify that the IP address is
set correctly.
If the test failed, a notification window will pop up,
then you need to check the network connection
status and make sure the IP address is set
correctly and then run the connection test again.
IP Setting
There are two ways to set IP address: Auto or
Manual.
Auto: Select Auto to obtain IP address
automatically.
Manual: Select Manual to set the IP address
manually.
Please following the steps below to set the IP
address manually:
1. The network confirgure screen will appear
after selecting “Manual”, and the cursor will be
located in IP address input box.
2. Use number buttons to enter IP address
manually.
3. Press Enter button to confirm the settings.
GB-17
English
Playback
BD-Live Connection
English
This player is capable of accessing content from
the internet. Using this option to control which
websites the BD player is allowed to access
additional content. Available settings are:
Permitted: Allow the inserted Blu-ray disc to
access content from all BD-LiveTM Internet sites
whose Internet address is encoded onto the disc.
There is no danger of malicious code download
from valid commercial Blu-ray discs, but choosing
this option and downloading BD-LiveTM content
via illegally authored Blu-ray discs, or discs
obtained from questionable sources, could result
in malicious code being downloaded onto the Bluray player.
Partial Permitted: Only allow the inserted Bluray disc to download content from a BD-LiveTM
website which has a valid online certificate. This
will reduce the chances of downloading malicious
content onto the player.
Prohibited:Block inserted Blu-ray disc from
accessing BD-LiveTM content over the Internet.
Proxy Setting
Use this option to set the Proxy: Enable, Disable,
Proxy Host, Proxy Port.
HDMI Deep Color
Use this option to set the HDMI deep color as 30
bits, 36 bits, 48 bits or off.
HDMI 1080p 24Hz
Enable/disable HDMI 1080p 24Hz.
Video Process
Video Adjust
Use this option to adjust the brightness, contrast,
hue and saturation.
Press Left/Right direction button to adjust, press
Return button to exit.
Sharpness
Use this option to select the sharpness level of the
video. Available settings are: High, Medium, Low.
Motion Video Process
Video Mode
Use this option to select the video mode. Available
settings are: Standard, Vivid, Smooth.
Audio Setting
Display Setting
Audio Output
TV
TV Screen
Select this option to set the aspect ratio of your
TV, the available settings are: 16:9 Full, 16:9
Normal, 4:3 Pan&Scan, 4:3 Letterbox.
Resolution
Use this option to select the video output
resolution: Auto, 480i/576i, 480p/576p, 720p,
1080i or 1080p*.
Auto: The player will select the resolution that
best matchs your TV automatically.
* The number indicates the number of scanning
lines.I,p indicates the scanning format of an
image signal.
TV System
Use this option to set the TV system in your area:
PAL, NTSC, Auto.
Color Space
Use this option to set the color space as RGB,
YCbCr, YCbCr422 or Full RGB.
Spdif
Use this option to set the SPDIF audio output
format. The available settings are:
Bitstream: Outputs the original signal without
processing.
PCM: Outputs the Linear PCM signal.
OFF:Disables output signal from SPDIF.
HDMI
Use this option to set the audio signal format
when your player is connected to an amplifier
or receiver using an HDMI cable. The available
settings are:
Bitstream: Outputs the original signal without
processing.
PCM: Outputs the Linear PCM signal.
OFF:Disables output signal from HDMI.
Down-Samp
Use this option to select the PCM downsampling
rate of digital audio signal. The available settings
are: 48K, 96K, 192K.
Note: Setting an incorrect PCM sampling rate
may result in unpredictable audio playback.
DRC
Use this option to set the dynamic range
compression as Off, On, Auto.
GB-18
Speaker Setting
Configuration
Use this option to select output configuration.
Title: Displays current title number/total number
of titles.
Chapter: Displays current chapter number/total
number of chapters.
Time: Displays the current playback time and total
time. Press Up/Down direction button to view the
remaining time.
Test Tone
Use this option to test the speaker connections.
Post Process
EQ
Sets the EQ
Mode: Select the playback mode.
System Information
Select this option to view the system information:
software version, MAC address.
Basic Operations
Playing a Disc
1.Press the Power button to turn on your player.
2.Switch the input selector on your TV so that
the signal from the player appears on your TV
screen.
3.Press Open/Close button to open the disc tray.
4.Place the disc on the disc tray with the
playback side facing down.
5.Press Open/Close button to close the disc tray.
6.Press Play/Pause button to start playback.
7.When you finish playing, press Open/Close
again to open the disc tray.
8.Remove the disc, and press Open/Close again
to close the disc tray.
9.Press Power button to turn off the player.
On screen Display Menu
During playback, press “Angle” button to display
OSD (on screen display) menu. You can control
the playback by using OSD menu.
Playing video files
Press Angle button while playing video files to
display the OSD menu, as shown below:
Audio: Sets the audio output language of BD/
DVDs. discs.Press Up/Down direction button to
select the desired language.
Angle: Displays the current angle information.
Press Up/Down direction button to select the best
viewing angle.
• Only applicable to the discs that have multiangle capabilities.
Subtitle: Selects the subtitle language. Press
Up/Down direction to select the desired subtitle
language or turn off the subtitle.
Subtitle type: Use this option to change the
display effect of the plug in subtitle. This feature is
only available when playing video files.
Second Video: Press Up/Down direction button
to turn on/off the secondary video (if available).
If this function is enabled and the disc supports
PIP mode, the primary video will be displayed on
the full screen, and the secondary video will be
displayed in a small window.
Second Audio: Press Up/Down direction button
to turn on/off the secondary audio (if available).
If this function is enabled and the disc supports
PIP mode, your player will output the secondary
audio for the secondary video.
Bitrate: Displays the current output bit rate.
Still Off: Some discs support freezing of video
pictures as a still picture to provide better image
view. Select this option to disable the Still function.
Availability of the Still function depends on the
inserted disc.
Instant Search: Advances playback.
Instant Replay: Rewinds playback.
Note: Availability of these functions depends on
the inserted discs.
GB-19
English
Use Up/Down direction to highlight the item,
press Enter or Right button to select.
The OSD menu has the following options:
Checking the Disc Information
Playing image files
Press Angle button while playing image files to
display the OSD menu, as shown below:
BD
DVD
DATA DVD
CD
Press INFO button to check the title/chapter etc.
information. The information differs depending on
the disc type and the player status.
English
Example: when playing a BD-ROM.
File: Displays current file number/total number of
files.
Playback Mode: Selects the image playback
mode.
Slideshow: Selects the slideshow speed.
Transition: Selects a transition mode for browsing
your photos.
The following information appears:
1. Playback status
2. Disc type
3. Title information: The current title number/total
number of the titles.
4. Chapter information: The current chapter
number/total number of the chapters.
5. Playback time.
Playing audio files
Press Angle button while playing audio files to
display the OSD menu, as shown below:
File: Displays current file number/total number of
files.
Time: Displays the current playback time and total
time. Press Up/Down button to view the elapsed
time/remaining time.
Mode: Selects the playback mode.
Bitrate: Displays the current output bit rate.
Instant Search: Advances playback.
Instant Replay: Rewinds playback.
GB-20
Introduction
Media center allows you to browse and play media
files such as videos, photos and music files stored
on a data disc or a USB flash drive.
Supported Functions
Your player supports the following functions:
Video playback:
>> Pause, Resume, Stop, Fast forward, Fast
reverse, Repeat.
>> Skip to next video, skip to previous video.
Audio playback:
>> Pause, Resume, Stop, Fast forward, Fast
reverse,
>> Repeat.
>> Skip to next song, skip to previous song.
Image playback:
>> Thumbnail Display
>> Slideshow
Tips:
• To implement these functions, please refer to
“Remote Control”.
• You can use OSD menu to control the playback,
please refer to “On Screen Display Menu” for
OSD operation.
Operation Steps
1. Selecting playback source
After instering a disc/USB flash drive, press Media
Center to display the Media Center screen, shown
as below:
Using Up/Down direction button to select the
playback source and press Enter to confirm.
Note:To select Media Center during disc playback,
you should stop playback first.
1.1 Using Pop up Menu
Press Pop up button to display pop up menu after
selecting a file/folder.
Pop up menu allows the user to perform file/folder
operations , shown as below:
Add to the playlist: To add files/folders to the
play list.
Select all: To select all files/folders.
Clear all: To clear all selections.
Cancel: To exit.
1.2 Playlist
You can customize your playlist by adding files/
folders to the playlist. The steps are shown as
below:
a. Select playlist and press Enter to enter the submenu: Photo, Music and Video.
b. Select the media type you want to play and
press Enter to enter the folder.
c. Select the desired file and press Enter to start
playback.
Note: The current playlist will be cleared after
restarting.
2. Selecting Media for Playback
The following screen will appear after selecting
playback source, using Up/Down direction button
to select the media type (Photo/Music/Video) and
press Enter to confirm.
You can press “..” or the Left direction button to
return to the previous menu.
3. Playing Photo/Audio/Video Files
3.1 Playing Photo files
Supported file formats: JPG, BMP, PNG etc..
(1)From the above (Select Media) Screen, press
Up/Down button to enter Photo file folder and
then select the desired file.
(2) Press Enter to start playback.
Note: A resolution problem can cause that images
are not being displayed correctly.
3.2 Playing Audio files
Supported file formats: mp3 etc..
(1)From the above (Select Media) Screen, press
Up/Down button to enter Music file folder and
select the desired file.
(2)Press Enter or Right direction button to start
playback.
The preview area will display the audio file type,
total playback time, title etc. information.
3.2 Playing Video files
Supported file formats: AVI, MPG, VOB, RM, etc..
(1) From the above (Select Media) Screen, press
Up/Down direction button to enter video file
folder and select the desired file.
(2)Press Enter or Right direction button to start
playback.You can view video thumbnails in the
lower right corner of the screen.
Note: Please close the USB rubber stopper
to prevent dust and ESD damage after
removing the USB flash drive.
GB-21
English
Using Media Center
Troubleshooting
No sound is output from the HDMI OUT jack
• Try the following:
1 Turn the player off and on again.
2 Turn the connected equipment off and on again.
3 Disconnect and then reconnect the HDMI cord.
• The HDMI OUT jack is connected to a DVI
device (DVI jacks do not accept audio signals).
If you experience any of the following difficulties
while using the player, use this troubleshooting
guide to help remedy the problem before
requesting repairs. Should any problem persist,
consult your nearest dealer.
English
Picture
There is no picture/picture noise appears.
• Re-connect the connecting cord securely.
• The connecting cords are damaged.
• Check the connection to your TV and switch the
input selector on your TV so that the signal from
the player appears on the TV screen.
• The disc is dirty or flawed.
• When playing a double-layer DVD, the video
and audio may be momentarily interrupted at the
point where the layers switch.
• If your TV can not output high definition video, press
HDMI button on the remote to switch the resolution
to 480i/576i automatically for normal playback.
There is no picture or picture noise appears
when connected to the HDMI OUT jack.
• Try the following:
1 Turn the player off and on again.
2 Turn the connected equipment off and on again.
3 Disconnect and then connect the HDMI cord again.
• If the HDMI OUT jack is used for video output,
changing the video output resolution may solve
the problem.
The picture does not fill the screen, even
though the aspect ratio is set in “TV
aspect”under “Display”
• The aspect ratio of the disc is fixed on your BD/
DVD.
The dark area of the picture is too dark/the
bright area is too bright or unnatural.
• Set “TV Aspect Ratio” in “Display” to “16:9 Wide”
(default).
Sound
There is no sound.
• The disc is dirty or flawed.
• Re-connect the connecting cord securely.
• The connecting cord is damaged.
• The player is connected to the wrong input jack
on the amplifier (receiver).
• The amplifier (receiver) input is not correctly set.
• The player is in pause mode or in Slow-motion
Play mode.
• The player is in scan mode.
• If the audio signal does not come through the
DIGITAL OUT (OPTICAL)/HDMI OUT jack,
check the audio settings.
• If you only connect AUDIO L&R jacks, please
set 2X in Configuration of the Speaker setting.
The sound volume is low.
• The sound volume is low on some BDs/DVDs.
• The sound volume may improve if you adjust the
TV or Amplifier volume output level.
Operation
The remote does not function.
• The batteries in the remote are weak.
• There are obstacles between the remote and the
player.
• The distance between the remote and the player
is too far.
• The remote is not pointed at the remote sensor
on the player.
The disc does not play.
• The disc is loaded upside down. Insert the disc
with the playback side facing down.
• The disc is not fit to the disc tray absolutely.
• The player cannot play certain discs.
• The region code on the BD/DVD does not match
the player.
• Moisture has condensed inside the player.
• The player cannot play a recorded disc that is
not correctly finalized.
• The file on the DATA DVD contains characters
other than numbers and English alphabet.
The photo file cannot be played.
• The disc is dirty or flawed.
• The image is larger than 4,096 (width) × 4,096
(height) in normal mode. (Some progressive
JPEG files cannot be displayed even if the file
size is within this specified capacity.)
• The image does not fit the screen (the image is
reduced).
• The photo file format does not conform to DCF*.
• Characters other than numbers and English
alphabet are contained in the file name.
The file name is not correctly displayed.
• The player can only display numbers and
alphabet. Other characters may be displayed
differently.
• Depending on the writing software used, the
input characters may be displayed differently.
The disc does not start playing from the beginning.
• Random Play or Repeat Play is selected.
• Resume play mode is on.
Some functions such as Stop, Search, Slowmotion Play, Repeat Play, or Random Play
cannot be performed.
• Depending on the disc, you may not be able to
do some of the operations above. Refer to the
operating manual that comes with the disc.
GB-22
Model BDP-620
System Laser: Semiconductor laser
Outputs Jack name
AUDIO OUT L/R
DIGITAL OUT (OPTICAL)
VIDEO
Jack type
Output level
Phono jack
Phono jack
Phono jack
2 +0.1 Vrms
0.5 Vp-p
1.0+0.2 Vp-p
HDMI OUT
General Power requirements
HDMI 19-pin standard connector
Power consumption Operating
temperature
100-240 V AC, 50/60 Hz
20 W
5 oC to 35 oC
Dimensions (approx.)
Weight (approx.)
483 x 44 x 210 mm (incl. brackets) 1.95 kg
430 x 38 x 210 mm (excl. brackets)
(width/height/depth)
Load
impedance
10 kilohms
75 ohms
75 ohms
Operating
humidity
25 % to 80 %
Hint:
Specifications and design are subject to change without notice.
FOR MORE INFORMATION PLEASE VISIT OUR WEBSITE
WWW.NEWHANK.COM
GB-23
English
Specification
Download PDF