Automatic Technology Australia | GDO-2 SecuraLift | Troubleshooting guide | Automatic Technology Australia GDO-2 SecuraLift Troubleshooting guide

GDO-9v2 SecuraLift®
Overhead Garage Door Opener
Featuring TrioCode™ Technology
Part # 13212 (Manual)
INSTALLATION INSTRUCTIONS | OWNERS COPY
WARNING: It is vital for the safety of persons to follow
all instructions. Failure to comply with the installation
instructions and the safety warnings may result in serious
personal injury and/or property damage.
Please save these instructions for future reference.
Automatic Technology (Australia) Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all
conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of an
Automatic Technology (Australia) Pty Ltd Garage Door Opener. Automatic Technology (Australia) Pty Ltd hereby further
expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any person
as a result whether directly or indirectly from failure to install the Automatic Technology (Australia) Pty Ltd Garage Door
Opener in accordance with these installation instructions.
2
GDO-9v2 SecuraLift® Owner Installation Instructions
GDO-9v2 SecuraLift®
Overhead Garage Door Opener
Important Safety Instructions
4
Features
6
Operating Controls
8
Kit Contents
10
Installation
11
Knockdown C-Rail Assembly
11
C-Rail Attachment
12
Determine Door Type
13
Mounting - Track Type Door
14
Photo Electric Beam Installation
23
Mounting - Spring Loaded Door
15
Auto-Close Setup
23
Mounting Door Bracket & Arms
16
SmartSolar™ Installation
24
17
Battery Back Up installation
25
Programming the Opener
Setting Travel Limits - Control Panel 17
Setting Travel Limits - Transmitter
Safety Obstruction Forces
Safety Obstruction Force Test
Final Set Up
23
26
18
Courtesy Light Time
26
19
Pet Mode Door Height
26
19
Wall Mounted Transmitters
26
Re-Initialising
26
Adjusting Safety Obstruction Forces 20
Coding Transmitters
Accessories
21
Parameters
27
Door
21
Default Settings & Specifications
27
Courtesy Light
21
Door Status Indicators
28
Pet Mode
21
Troubleshooting Guide
30
Vacation Mode
21
Maintenance Record
31
Remotely Coding Transmitters
22
Parts Listing
32
Erasing Transmitter Codes
22
Warranty
34
Owner Installation Instructions GDO-9v2 SecuraLift®
3
Important Safety Instructions
WARNING: It is vital for the safety of persons to follow
all instructions. Failure to comply with the following
Safety Rules may result in serious personal injury and/or
property damage.
CAUTION: If your garage has no pedestrian entrance door, an emergency access device should be installed.
This accessory allows manual operation of the garage door from outside in case of power failure.
For ADDITIONAL SAFETY protection we STRONGLY recommend the fitting of a Photo Electric (P.E.)
Beam. In most countries P.E. Beams are mandatory on all garage doors fitted with automatic openers.
For a small additional outlay Automatic Technology recommends that Photo Electric Beams be
installed with the automatic opener ensuring additional safety and peace of mind.
DO NOT operate the opener unless the garage door is in full view and free from objects such
as cars and children/people. Make sure that the door has finished moving before entering or
leaving the garage.
DO NOT operate the opener when children/persons are near the door. Children must be
supervised at all times when the SecuraLift® is in use. Serious personal injury and/or
property damage can result from failure to follow this warning.
DO NOT allow children to operate the SecuraLift®. Serious personal injury and/or
property damage can result from failure to follow this warning.
Regularly check to make sure that the safety obstruction force is working
correctly, and is tested and set as per page 19 of this manual. Failure to
follow these instructions could result in serious personal injury and/or
property damage. This test must be repeated at regular intervals and the
necessary adjustments made as required.
Doors requiring over 400N of force to move must have P.E. Beams
installed.
DO NOT disengage the door opener to manual operation with
children/persons or any other objects including motor vehicles
within the doorway.
The door opener is not intended for use by young children
or infirm persons without adequate supervision. Children
should be supervised to ensure that they do not play
with the remote transmitters or the opener.
Keep hands and loose clothing clear of the door
and door opener at all times.
4
GDO-9v2 SecuraLift® Owner Installation Instructions
Important Safety Instructions
The unit should be installed so that it is protected from the elements. It should not be exposed to water or rain.
It is not to be immersed in water or sprayed directly by a hose or other device.
The garage door must be well balanced. Sticking or binding doors must be repaired by a qualified garage
door installer prior to installation of the opener.
Frequently examine the installation, in particular cables, springs and mountings for signs of wear, damage
or imbalance. DO NOT use if repair or adjustment is needed since a fault in the installation or an
incorrectly balanced door may cause injury. DO NOT attempt to repair the door yourself as hardware
is under extreme tension.
Remove or disengage all garage door locks and mechanisms prior to installation of the opener.
Connect the opener to a properly earthed general purpose 240V mains power outlet installed
by a qualified electrical contractor.
Disconnect the power cord from mains power before making any repairs or removing
covers. Only experienced service personnel should remove covers from the opener.
When using auto close mode, a photo electric beam must be fitted correctly and
tested for operation at regular intervals. Extreme caution is recommended when
using auto close mode. All safety rules must be followed.
In order for the SecuraLift® to sense an object obstructing the door way, some
force must be exerted on the object. As a result the object, door and/or
person may suffer damage or injury.
If the power supply cord is damaged, it must be replaced by an
Automatic Technology service agent or suitably qualified person.
Make sure that the door is fully open before driving in or out of the
garage and fully closed before leaving the driveway.
Make sure that remote controls are kept out of reach of
children.
Install the wall switch or wall mounted transmitter in
a location where it is out of reach of children and the
garage door is visible.
Owner Installation Instructions GDO-9v2 SecuraLift®
5
Features
Thank you for purchasing the Automatic Technology
GDO-9v2 SecuraLift® Overhead Garage Door
Opener. Designed to suit sectional overhead and one
piece tilt up doors, the components and materials
used ensure this opener will provide years of
smart, simple and secure operation. Listed
below are some of the many features:
Operation
To open or close the door simply press a button on a TrioCode™ handheld
transmitter, a wall mounted transmitter, or optional wall switch for two seconds.
During open and close cycles the door can be stopped by pressing the button
again. The next actuation will move the reverse the door’s direction.
TrioCode™ Code Hopping Technology
Every time a TrioCode™ transmitter is used a new security code is randomly
generated from over 4.29 billion possibilities. This greatly enhances the security
of the system and makes “code grabbing” a thing of the past
These transmitters also overcome interference issues by simultaneously sending a
signal over three different frequencies. Even if two of the three signals are jammed,
the system will still work.
ALPS (Automatic Limits Positioning System)
ALPS does away with manual adjustment of the door’s limits position using mechanical
parts, such as cams and microswitches. During installation the hand held transmitter
can be programmed to set the door limits positions.
ISS (intelligent safety obstruction system)
While the door is performing a close cycle, should it hit an obstacle or be restricted in some
manner, it will automatically reverse. The amount of force the door should encounter before
reversing is automatically adjusted by the doors control system during the initial installation of the
automatic door opener. The door will also stop if restricted whilst opening. The Safety Obstruction
Force should be checked monthly.
Auto courtesy light
The courtesy light comes on automatically for three minutes whenever the door is activated. The light can also
be operated independently of the door by coding a dedicated button on a transmitter.
6
GDO-9v2 SecuraLift® Owner Installation Instructions
SmartSolar™ and Battery Back Up Compatibility (optional)
The opener can be fitted with a SmartSolar™ or Battery Back Up kit for operation in the
event of a power outage, or where mains power access is not available. NOTE: If the
door is the only entrance to the garage, and a battery back up kit is not fitted, a
keyed cable release should be fitted external to the garage.
Vacation mode
A hand held transmitter can be programmed to lock and unlock all other
transmitters that have been programmed into the openers’ memory. The vacation
mode can be used when the door is left idle for long periods of time.
Pet/Pedestrian mode
The transmitter can be programmed to open the door to an adjustable partial
height so that the family pet can enter and exit the garage at any time. You may
also wish to open the door to a height suitable only for pedestrian access.
Auto-close mode
The opener can be programmed to automatically close after an open cycle. The autoclose time is adjustable. It is compulsory to install a P.E. Beam if this mode is selected,
otherwise the door may cause personal injury or damage to property.
Photo Electric (P.E.) Beam (optional)
The opener has an input to connect a P.E. Beam for extra safety and use of the auto-close
mode.
Manual operation
The opener is equipped with a unique manual disengaging device. If the power to the opener is disrupted the
door can be put into manual mode by pulling down on the string handle on an angle towards the door. This
allows for manual operation of the door. To re-engage the opener pull the string handle away from the door.
Owner Installation Instructions GDO-9v2 SecuraLift®
7
Operating controls
01
02
03
04
P.E. Shunt. The shunt has to be removed when connecting a Photo Electric Beam.
NOTE: P.E. Shunt must only be removed when P.E. Beams are being connected, otherwise the opener will
malfunction.
Terminal Block.
•
24V PWR is used to power devices such as:
»
PE (Input) for photo electric beam for safety and auto-close function.
»
LGT (Input) allow hard wired external trigger for the opener’s courtesy light.
»
O/S/C INPUT is used for the connection of a wired switch (momentary contact). This switch
can then be used to open, stop or close the door. Install the wall switch in a location where
the switch is out of reach of children and the garage door is visible.
SET button (yellow) is used during the installation phase together with the Open and MINUS (-) buttons to
set the door limit positions. The Set button is also used to re-initialize the Opener.
LIGHT CODE button (white) is used for storing or erasing the transmitter button (code) you wish to use
to switch the courtesy light on the opener on or off.
05
CODING LED (red) light flashes when a code is being stored or when a transmitter button is pressed.
06
OPERATE button (Yellow) is used during installation to test the open, stop and close cycles for the
opener. The opener has to be initialised by the Reset button to make the O/S/C button operable.
07
DOOR CODE BUTTON (blue) is used for storing or erasing transmitter buttons for door operation
08
DOOR STATUS LED (Yellow)
09
10
PLUS (+) button (green) is used during installation to help set the open limit position. Pressing and holding
this button will move the door in the open direction, releasing stops the door.
NOTE: The safety obstruction detection is inoperable when the PLUS (+) button is used to move door.
11
CLOSE LIMIT LED (red) the LED is very helpful during installation. It illuminates and flashes when the
door is closing and remains steady on when the close limit position has been reached.
12
OPEN LIMIT LED (green) the LED is very helpful during installation. It illuminates and flashes when the
13
14
15
8
MINUS (-) button (red) is used during installation to help set the close limit position. Pressing and holding
this button will move the door in the close direction. Movement stops when the button is released.
NOTE: The safety obstruction detection is inoperable when the CLOSE button is used to move door..
door is opening and remains steady on when the open limit position has been reached.
AUTO CLOSE TIME button (White) is used to adjust the auto close time. While holding in the AUTO
CLOSE TIME button and then pressing the PLUS (+) button the time is increased. Each press will increase
the time by 5 seconds. Pressing the MINUS (-) button will decrease the time.
FORCE MARGIN SET Button: The obstruction force margin is set automatically during installation. The
margin can be adjusted manually using the Force Margin Set button (White). Holding the Force Margin Set
button and pressing PLUS (+) or MINUS (-) buttons will increase or decrease the amount of force. The Force
Margin Set should only be used if environmental factors (wind, etc.) affect the door’s operation.
J13 CONNECTOR onto this the shunt supplied with SmartSolar™ kit must be fitted for solar
operation.
GDO-9v2 SecuraLift® Owner Installation Instructions
18
17
01
16
02
15
03
04
05
06
07
08
09
10
11
12
13
14
16
PROG INPUT is used to connect the Automatic Technology Handheld Programmer for editing control
17
SBY-3 CONNECTOR is used to connect both Battery Back Up Kits and SmartSolar™ kits.
18
10A FUSE
and receiver functions, accessing diagnostic tools, and activating special features and operating modes.
Owner Installation Instructions GDO-9v2 SecuraLift®
9
Kit contents
Drive Unit
1 x GDO-9v2 SecuraLift® Trio drive unit (Fig. 01)
1 x TrioCode™ Transmitter pack (Fig. 01)
(Pack includes two keyring transmitters and batteries)
1 x Wall mount transmitter with battery (Fig. 01)
2 x Door attachment arms (Fig. 01)
1 x Accessory and hardware pack (Fig. 01)
1 x Manual Disengage Cord (Fig. 01)
1 x Installation Manual
fig 01
PLUS
Pre-Assembled Single Piece C-Rail
NOTE: The chain or belt in the one piece rail has been
tensioned by the factory. Do not adjust the tension of
the chain.
IMPORTANT NOTE: If a modification to the length of the
track is required, the adjustment must be made from the
drive unit end only.
fig 02
OR
Pre-Assembled Multi Piece C-Rail
Note: The chain or belt in the multi piece rail has been
tensioned by the factory. Do not adjust the tension of
the timing belt.
IMPORTANT NOTE: If modification to the track length
is required, adjustment must be made only from drive
unit end only.
fig 03
10
GDO-9v2 SecuraLift® Owner Installation Instructions
Knockdown C-Rail Assembly
Start
1 Swing
2
Swing and straighten
3 Slide sleeve
4 Cut cable tie
5 Swing
fig 04
7 Slide sleeve
Swing and straighten
6
Turn tracks around 9
10 Screws
Tension 1/2” hex bolt
8
Screws
Adjust chain tension: Move the shuttle to middle of track. Use a spring scale to
measure required force to pull the shuttle adjust 1/2” hex bolt to tension chain.
Recommended pull force: 8kg (80N)
Step 1 - Knockdown C-Rail Assembly
Unpack and assemble the C-Rail as shown above in Fig 04.
Owner Installation Instructions GDO-9v2 SecuraLift®
11
C-Rail Attachment
Step 2 - Attach Manual Disengage Cord
a.
b.
c.
d.
fig 05
If not already disengaged, flick the yellow clutch
lever up so it sits perpendicular to the rail.
Thread the loose end of the cord through the hole
in the yellow clutch lever (Fig. 05).
Thread the cord down to red toggle and knot
through the spare hole.
Test if secured properly by pulling back towards
sprocket end to engage, and the towards door end
to disengage.
Step 3 - Secure C-Rail to Drive Unit
a.
b.
Shaft
fig 06
Locate shaft into sprocket
Hex flange screw taptite ‘S’ M4 x 10
Track bracket (x2)
fig 07
12
GDO-9v2 SecuraLift® Owner Installation Instructions
Locate and insert the shaft of drive unit into the CRail’s sprocket (Fig. 06).
Fix the two track brackets with four screws supplied
in accessory pack (Fig. 07).
Determine the Door Type
Step 4 - Determine Door Type
Determine which type of garage door you have as
illustrated below. (Fig. 08 to 10).
For a sectional (panel) door on tracks (Fig. 08)
proceed with the installation from Step 5.
Track
fig 08
Door
Sectional door with track
For a one-piece door on tracks (Fig. 09)
proceed with the installation from Step 5.
fig 09
One piece door with
track
For a one-piece door without tracks (on springs) (Fig. 10)
proceed with the installation from Step 9.
Door
fig 10
One piece door
without track
Owner Installation Instructions GDO-9v2 SecuraLift®
13
Mounting on a Track Type Door
WARNING: The opener must be securely
fastened to structural supports, otherwise opener
failure may ensue causing serious personal injury
and/or property damage.
Level
Level
Track
fig 11
Track
Step 5 - Determine Bracket Position
Door
a.
Door
b.
c.
Open the door and find the highest point of travel of
the top door panel.
Using a level, transfer this height to the wall above
the door (Fig. 11) and mark a line 60mm above it.
Determine the centre point on the wall above and on
top of the door. Draw two lines extending 21.5mm
from each side of the centre point. (Fig. 12)
Step 6 - Mounting the Wall Bracket
a.
b.
c.
fig 12
Drilled holes
Centre the bracket over the intersection of these two
lines. Mark centres for at least two holes (Fig. 12).
Ensure this is into a solid mounting point
•
Drill holes into the wall with an appropriate bit.
Secure to the wall using:
IF CONCRETE OR BRICK - 8mm (5/6”) loxins/dynabolts.
IF TIMBER - wood screw #20 or similar (min. 50mm).
WARNING: Make sure concrete, brick wall or
timber lintels are solid and sound so as to form a
secure mounting platform.
Step 7 - Attach the Rail to the Wall
Bracket
a.
b.
fig 13
Attach the C-Rail assembly to the wall bracket
with the 90mm long clevis pin and secure with the
supplied snap pin (Fig. 13)
Leave the powerhead in its packing box for protection
during installation.
Step 8 - Secure the Powerhead to the Ceiling
a.
b.
c.
d.
Structural member
e.
fig 14
Raise the powerhead from the packing box and
support it in the horizontal position with a step
ladder.
Open the garage door. Rest the opener on the open
door and use a scrap piece of wood to bring it to
horizontal level.
Line up the track perpendicular to the wall.
Secure the perforated angle (not supplied) to
the ceiling above where powerhead’s mounting
holes will be once fully installed. A representative
mounting is shown (Fig. 14)
Connect the powerhead to the ceiling mounted
perforated angle with M8x20mm screws and nuts.
Strips should not extend more than 18mm below
centre of powerhead mounting holes.
Go to Step 14 on page 14.
14
GDO-9v2 SecuraLift® Owner Installation Instructions
Mounting on a non-Track Type Door
WARNING: The opener must be securely fastened to
structural supports, otherwise opener failure may ensue
causing serious personal injury and/or property damage.
Centre of Door
Step 9 - Determine the Door’s Centre
a.
b.
Find the centre of the door and mark this location
both above the door and on top of the door.
Draw two lines 21.5mm either side of this (Fig. 15).
fig 15
Step 10 - Prepositioning the Opener
a.
b.
c.
Raise the door to open position.
Rest the opener on the top edge of the door with
end of the rail against the wall (Fig. 136.
Support the powerhead level with the lowest point
of the open door (Fig. 16).
NOTE: Do not slide rail along the face of the door.
Step 11 - Mounting the C-Rail
a.
b.
c.
d.
e.
f.
g.
h.
Close the door slowly. The rail will be elevated by
the top edge of the door as it moves.
Stop the door when it is at its highest point of travel.
Allow 25mm additional height for clearance between
the door and the track (Fig. 17).
Support the Rail in this position and close the door
The height determined in Step 11(b) will be the
height at which to mount the wall bracket.
Centre the bracket along the line determined in Step
9
Using the bracket as a template, mark a minimum of
two holes and drill with appropriate size bit. For a
more secure fitting, the wall bracket can be anchored
using more than two holes.
Secure the bracket to the wall using:
IF CONCRETE OR BRICK - 8mm (5/6”) loxins/dynabolts.
IF TIMBER - wood screw #20 or similar (min. 50mm)
Attach the bracket and C-Rail with supplied pins (Fig. 13).
fig 16
Step
ladder
C rail
25mm
Highest point
of door travel
Door
WARNING: Make sure concrete, brick wall or
timber lintels are solid and sound so as to form a
secure mounting platform.
fig 17
Step
ladder
Step 12 - Secure the Powerhead to the Ceiling
b.
Secure the perforated angle (not supplied) to the
ceiling above where powerhead’s mounting holes
will be. See (Fig.14) for a representative mounting.
Connect the powerhead to the ceiling mounted
perforated angle with M8x20mm screws and nuts.
Strips should not extend more than 18mm below
centre of powerhead mounting holes (Fig. 14).
Drill hole at centre of
track (recommended
bolt size M6 or M8)
Ceiling
Step 12.1 - Alternative Mounting Option
The opener can be fastened to the roof by driving a bolt
through the C-Rail into a structural timber support. The
bolt head’s height must not exceed 6mm (Fig. 14).
Aluminium rail
fig 18
6mm M A X
(HEIGHT OF BOLT HEAD)
a.
Shuttle VP2 assembly
Owner Installation Instructions GDO-9v2 SecuraLift®
15
Mounting Door Bracket & Arms
Step 13 - Mounting Door Bracket
The door bracket comes in two parts. The bottom plate
with two mounting holes is used on its own for one piece
doors. For sectional doors, the top plate is placed over
the bottom plate and is fixed with four (4) screws (Fig.
19).
fig 19
a.
b.
Mount the door bracket, or bracket assembly,
on the door’s centre line one-third down the top
panel (Fig. 19) using M6 or equivalent screws (not
supplied),
STEEL DOORS ONLY: Bracket can be welded in
place.
NOTE: If in doubt about the door’s strength,
reinforcement may be added to the door’s frame
where necessary. Door damage may occur if the
bracket is installed on a panel with insufficient
strength. The opener’s warranty does not cover
damage caused to the door and/or door panels.
fig 20
Step 14 - Attaching the Arms
FOR SECTIONAL AND ONE PIECE DOORS WITH
TRACK:
a. Assemble the bent and straight arms with bolts
and nuts supplied in the accessory pack (Fig. 20).
Always use both bent and straight arms.
b. Connect the assembled arm to the bracket and the
disengaged trolley with clevis and snap pins. The
angle “A” must be more than 10° (Fig. 21).
0
10
fig 21
WARNING: Connecting the bent arm other way
around may damage the door. The straight arm
should not protrude beyond heal of bent arm
FOR ONE PIECE DOORS WITHOUT TRACK
a. Assemble the bent and straight arms as shown
in (Fig. 22) with bolts and nuts supplied in the
accessory pack. Always use both the bent and
straight arms.
b. Connect the assembled arm to the bracket and the
disengaged trolley with clevis and snap pins.
c. If installing on a door with a bad wave action,
lengthening the arm will assist in reducing this
effect.
IMPORTANT NOTE: Adjust the length of the
cord so that its toggle is no more than 1.8m from
the ground.
fig 22
16
GDO-9v2 SecuraLift® Owner Installation Instructions
Setting Limits
Step 15.1 - Setting Travel Limits
NOTE: If P.E. Beams are to be used they must be installed
before setting the travel limits.
WARNING! Use caution when operating the manual
release with the door open since it may fall rapidly
due to weak or broken springs, or an improperly
balanced door.
fig 23
CAUTION! Do not disengage the opener to manual
operation with children, persons or any objects
including motor vehicles within the doorway.
a.
b.
c.
d.
e.
f.
g.
h.
Engage the C-Rail’s trolley (attached to the door via
the arms) with the chain index by moving the door.
If the trolley does not “click” firmly onto the
»
chain index, ensure that the manual release
cord is not in the disengaged position by
pulling it backwards.
Turn on the power to the opener. The CLOSE LIMIT
LED will be flashing.
Remove the button cover with a small blade
screwdriver (Fig. 23).
Press and hold the MINUS (-) button - the door will
start closing (Fig. 24).
Release the MINUS (-) button when the door is near
the desired closed position. Single presses of the
MINUS (-) button will “inch” the door closed.
» If the door overshoots press the PLUS (+) button
to move the door in the open direction.
When the door is at the desired close position, press
the SET button to record the close limit position. The
OPEN LIMIT LED will now flash.
Press and hold the PLUS (+) button to open the door
(Fig. 25).
Release the PLUS (+) button when the door is near the
desired open position. Single presses of the PLUS (+)
button will “inch” the door open.
» If the door overshoots press the MINUS (-) button
to move the door in the open direction.
fig 24
WARNING! Once the next step is performed, the
door will automatically close and open to calculate
force settings. Keep persons and objects clear of the
door until it stops and the opener sounds a beep.
i.
Press the SET button to store the open limit. Please
read the above warning.
fig 25
Step 15.2 - Resetting Travel Limits
To reset the limits press and hold the MINUS (-) button for
6 seconds until the CLOSE LIMIT LED flashes quickly. If no
action is taken within 30 seconds, the opener will return to
normal operating mode and restore the original settings.
Owner Installation Instructions GDO-9v2 SecuraLift®
17
Setting Limits: via Transmitter
The GDO-9v2 has the alternate ability to set travel limits
using the transmitter, allowing free movement around
the garage to better assess the desired limit positions.
Step 16.1 - Code a Transmitter for Limit Setting
a.
b.
c.
fig 26
d.
Ensure the opener is powered up.
Press and hold the DOOR CODE button (Fig. 26).
Press Button 1 on the transmitter for two seconds
(Fig. 27). Release and pause for two seconds.
Press the Button 1 again for two seconds.
Release the DOOR CODE button.
Step 16.2 - Setting Limits via Transmitter
a.
b.
Button 1
(Inch Open)
c.
Button 4
(Inch Close)
fig 27
d.
Button 2
(Set)
Button 3
(Switch between
fast and slow
inching)
e.
f.
Engage the C-Rail’s trolley (attached to the door via
the arms) with the chain index by moving the door.
»
If the trolley does not “click” firmly onto the
chain index, pull the cord backwards until it
locks in place, and try again.
Press and hold Button 4 on the transmitter to close
the door. When the door is approx. 20mm from the
ground, press and hold Button 3 for two seconds
and release (Fig. 27).
Each press of Button 4 will allow you to “inch” the
door closed. Keep doing this until the door reaches
the desired close limit position.
»
If the door closes too far, press Button 1 to
“inch” the door towards open
When happy with the close limit position, press
Button 2 to store this in memory.
Press Button 1 to open the door. When approx.
20mm from the desired open position, press and
hold Button 3 for two seconds then release.
Each press of Button 1 will allow you to “inch” the
door open. Keep doing this until the door reaches
the desired open limit position.
»
If the door is opened too far, press Button
4 to “inch” the door towards closed
IMPORTANT
WARNING: The door will
automatically close, open and close again once
Step 16.2(f) is performed. Ensure that no persons
or objects are in the door’s path.
f.
g.
When happy with the open limit position, press
Button 2 on the transmitter to store into memory.
The door will now automatically close and open to
calculate the safety obstruction settings. After this, the
opener can be operated with the OPERATE button.
Step 16.3 - Resetting the Door Limit Positions
Limit positions can be deleted by the following steps:
a. Follow Steps 15.2 (a) and (b), as outlined previously.
b. Repeat Steps 16.1 and 16.3 to set new travel limit
positions.
There is no need to re-code the transmitter
»
(Step 16.2) upon resetting travel limits. The
transmitter will still be stored in memory.
18
GDO-9v2 SecuraLift® Owner Installation Instructions
Safety Obstruction Force Test
WARNING! Take care when testing or adjusting
the Safety Obstruction Force. Excessive force
may cause SERIOUS PERSONAL INJURY and/or
PROPERTY DAMAGE.
Step 17.1 - Testing Close Cycle
a.
b.
c.
Press the OPERATE button to open the door (Fig.
28).
Place a piece of timber approximately 40mm high
on the floor directly under the door (Fig. 29).
Press the OPERATE button to close door. The door
should strike the object and start to re-open.
fig 28
Step 17.2 - Testing Open Cycle
a.
b.
c.
Press the OPERATE button to close the door (Fig.
28).
Press again to open the door. When the door
reaches the half open point, grab the bottom rail of
the door firmly and the door should stop.
If the door does not reverse readily when closing,
or stop when opening, the force may be excessive
and need adjusting, refer below.
DANGER! If the door fails these tests, put the
opener into manual mode, only operate the door
by hand and call for service.
fig 29
Owner Installation Instructions GDO-9v2 SecuraLift®
19
Adjusting Safety Obstruction Forces
Adjusting Safety Obstruction Force
The Safety Obstruction Force is calculated automatically
during setup. Adjusting this is normally only necessitated
by environmental conditions such as windy or dusty areas,
and areas with extreme temperature changes.
WARNING: Doors requiring over 400N of force to
move must have P.E. Beams fitted for safety.
fig 30
Step 18.1 - To Increase Force Pressure
a.
b.
c.
d.
Hold down FORCE MARGIN SET button (Fig. 30)
While holding the FORCE MARGIN SET button,
press the PLUS (+) button. Each press increases the
force margin (Fig. 30).
The OPEN LIMIT LED will flash each time the PLUS
(+) button is pressed to indicate a force increase
If the OPEN LIMIT LED flashes continuously
»
when pressing the PLUS (+) button this
indicates that the maximum setting has
been reached.
Test the force again as per Steps 8.1 and 8.2
Step 18.2 - To Decrease Force Pressure
a.
b.
c.
fig 31
d.
Hold down FORCE MARGIN SET button (Fig. 30)
While holding the FORCE MARGIN SET button,
press the MINUS (-) button. Each press decreases
the force margin (Fig. 30).
The CLOSE LIMIT LED will flash each time the MINUS
(-) button is pressed to indicate a force decrease
If the CLOSE LIMIT LED flashes continuously
»
when pressing the MINUS (-) button this
indicates that the maximum setting has
been reached.
Test the force again as per Steps 8.1 and 8.2
Step 18.3 - To Recall Factory Set Force
a.
b.
While holding down the FORCE MARGIN SET
button, press the SET button for two (2) seconds.
(Fig. 31)
Release both buttons. The default setting should
now be recalled.
Step 18.4 - To Recalculate Force Margins
a.
b.
fig 32
c.
d.
20
GDO-9v2 SecuraLift® Owner Installation Instructions
Press and hold the SET Button for two (2) seconds,
the beeper will sound once (Fig. 32).
The door will start to move and re-calculate force
margins. The door can move between the open and
close limit positions up to four (4) times (depending
on the position of the door and the power up
condition).
A single beep will be heard once the process is
complete.
Test the force again as per Steps 8.1 and 8.2.
Coding Transmitters
Step 19.1 - Code a Transmitter Button for
Door Operation
a.
b.
c.
d.
Press and hold the DOOR CODE button (Fig. 33).
Press one of the four buttons on the transmitter for
two (2) seconds, pause for two (2) seconds, then
press the same button again for two (2) seconds.
Release the DOOR CODE BUTTON.
Press the transmitter button to test.
fig 33
Step 19.2 - Coding a Transmitter Button to
the Courtesy Light
The transmitter can be programmed to operate the
courtesy light on the opener independently of the door
moving.
a. Press and hold LIGHT CODE button (Fig. 34).
b. Press one of the four buttons on the transmitter for
two (2) seconds, pause for two (2) seconds, then
press the same button again for two (2) seconds.
c. Release the LIGHT CODE button.
d. Press the transmitter button to test.
fig 34
Step 19.3 - Code a Transmitter Button for Pet
(Pedestrian) Mode
a.
b.
c.
d.
Press and hold both the DOOR CODE and MINUS
(-) buttons (Fig. 35).
Press one of the four buttons on the transmitter for
two (2) seconds, pause for two (2) seconds, then
press the same button again for two (2) seconds.
Release the DOOR CODE and MINUS (-) buttons.
Press the transmitter button to test. To change the
default pet (pedestrian) door opening position,
refer Step 2.
fig 35
Step 19.4 - Code a Transmitter Button to
Enable Vacation mode
The opener can be programmed into a “Vacation Mode”
where the opener will not respond to any transmitter
except one preprogrammed unit.
a.
b.
c.
d.
e.
Press and hold LIGHT CODE and MINUS (-)
buttons (Fig. 36).
Press one of the four buttons on the transmitter for
two (2) seconds, pause for two (2) seconds, then
press the same button again for two (2) seconds.
Release LIGHT CODE and MINUS (-) buttons.
To test, press and hold the transmitter button for
five seconds to set Vacation Mode.
To reset Vacation Mode press the same button
for two seconds.
fig 36
Owner Installation Instructions GDO-9v2 SecuraLift®
21
Remote Coding & Deleting
Transmitters
Step 20 - Remotely Coding Transmitters
Using this method transmitters can be coded without
access to the opener’s control panel as long as a precoded transmitter is available.
IMPORTANT NOTE: The door or courtesy light
must activate when the steps below are performed.
This indicates that the pre-coded transmitter is in
range of the opener, and the correct button has
been pressed.
fig 37
a.
b.
c.
d.
e.
Take any pre-coded transmitter. Press the button
for the function to be duplicated and release.
Using a small needle, press and hold firmly for
two seconds through the Coding Hole (Fig. 37).
WITHIN 10 SECONDS take the additional
transmitter you wish to code. Decide which
button that you want to activate the function to
be duplicated (e.g. activate the door, or turn on
the courtesy light)
Hold the new transmitter’s button for two
seconds, pause for two seconds, hold again for
two seconds and then release.
Wait for 10 seconds and then press the new
transmitter’s button to test.
fig 38
Step 21.1 - Deleting a Stored Transmitter
Code
a.
b.
c.
d.
Select the transmitter you want to delete.
Press and hold the DOOR CODE BUTTON (Fig.
38).
Press the transmitter button you would like to
delete for two seconds, pause for two seconds,
press again for two seconds and then release.
Release the DOOR CODE BUTTON. The code
should now be deleted. Confirm this by pressing
the transmitter button - the function (e.g. door
opening) should not respond.
Step 21.2 - Deleting All Transmitter Codes
a.
b.
c.
d.
22
GDO-9v2 SecuraLift® Owner Installation Instructions
1. Turn off power to the opener.
While switched off, press and hold the DOOR
CODE BUTTON (Fig. 38). Turn on power to the
opener while holding this button.
The OPEN LIMIT, CLOSE LIMIT and DOOR
STATUS LEDs will illuminate for about five
seconds. These LED’s will turn off and the
CODING LED will illuminate.
Release the DOOR CODE BUTTON. All stored
codes will now be deleted. Confirm this pressing
buttons on any previously coded transmitters the opener should not respond.
P.E. Beam & Auto-Close
Step 22 - Fitting the P.E. Beams (optional)
Affix the P.E. Beams in a strategic location within
the doorway. We recommend 150mm above the
floor level and as close as possible to the door
opening, inside the garage.
Remove the shunt from P.E connector (Fig. 39).
Connect the wires from the P.E. wiring harness to
terminal block (Fig. 40). The wiring diagram is for
Model PHBE (Order Code 90214).
a.
b.
c.
Remove
PE shunt
fig 39
Make sure to align the beams correctly. Follow the
manual supplied with the P.E. Beams.
WARNING: When using Auto Close Mode and P.E.
beams, the doorway must be clear of all obstructions
and persons at all times. The location of the beam
sand manner in which it is installed might not give
safety protection at all times. Check to make sure
that the height of the beam and type used give
maximum protection possible.
Model PE-2
Transmitter
Receiver
Step 23 - Setting Up Auto-close Mode
1 2 3 4 5
IMPORTANT NOTICE: It is compulsory to have P.E.
Beams installed when using Auto-close mode.
Auto-close mode is a function that automatically closes
the door a preset time after the P.E. Beams recognise
that a vehicle has left the garage.
fig 40
Cable 1
Cable 2
Red 24V
Black 0V
The Auto-close timer only starts after the P.E. Beam’s
path is broken the Auto-close timer has been set. If
the P.E. path is not broken the door will remain open
until the path is broken. If the opener incurs a physical
obstruction (i.e. not from the P.E. Beams) while closing
the door will re-open and not Auto-close until the P.E.
Beam’s path is broken again.
Yellow PE
24V
0V
PE
LGT
OSC
COM
Step 23.1 - Setting Auto-close Time
a.
b.
c.
d.
e.
Hold down the AUTO CLOSE TIME button (Fig. 30).
While holding in the AUTO CLOSE TIME button,
press the PLUS (+) button - each press will add
one second to the Auto-close delay.
To decrease the delay time follow Step 15.1(a)
and press the MINUS (-) button - each press will
deduct one second from the Auto-close delay.
Press the OPERATE button or transmitter to open
the door. When the door is fully opened the
OPEN LIMIT LED will flash to indicate that Autoclose mode is operational.
Break the P.E. Beam’s path momentarily to
initialise Auto-close. When the door reaches the
fully opened position, the door will pause for the
set Auto-close time and then close.
fig 41
Owner Installation Instructions GDO-9v2 SecuraLift®
23
SmartSolar™ Installation
PLEASE NOTE: Control board firmware must be
v1.32 or higher for SmartSolar™ compatibility
WARNING: Do not connect batteries until Step
24.3
Step 24.1 - Mount the Charger Board
a.
b.
Fig 42
c.
d.
e.
f.
Unplug the drive unit from mains power.
Remove the screws, swing open the main cover and
remove the light diffuser. Then remove the transformer,
EMC board (if fitted) and mains power cable.
Fix the Charger Board under the timing assembly
using three (3) M4x8 screws (Fig. 42).
Plug the Charger Board’s three wire harness (red/
yellow/black) into the control board’s “SBY-3”
connector (Fig. 43).
Plug the Charger Board’s white one wire harness into
the control board’s “24vac in” connector (Fig. 43).
Plug the solar shunt (supplied) onto the control
board’s “J13” connector (Fig. 43)
IMPORTANT WARNING: Do not connect battery
or solar panel polarity incorrectly - this will result in
serious damage to components.
Fig 43
Step 24.2 - Connect the Solar Panel
a.
b.
c.
Mount the solar panel as outlined in the SmartSolar™
Installation Manual.
Feed the Solar Panel’s cable through black grommet
located on the top of the plastic drive unit cover.
Connect the red wire to the Charger Board’s
“SOLAR+” connector, and the black wire to the
“–SOLAR” connector (Fig. 44).
WARNING: During Step 24.3 the opener will
become active.
Step 24.3 - Mount & Connect the Battery
e
Whit
Yellow
Red
a.
b.
c.
ry)
ttery)
Red (From Ba
tte
Black (From Ba
Red (From Solar P
anel)
olar Panel)
Black (From S
Fig 44
ire
W
ck
ire
a
l
B
dW
e
R
d.
e.
f.
Fig 45
Mount the Battery Box close to the opener.
Feed the 2-core 18awg gauge cable (supplied)
through the Battery Box’s grommet.
Connect the red wire to the Battery Box’s “+” terminal,
and the black wire to the “–” terminal (Fig. 45).
Feed the other end of the battery cable through the
drive unit’s black grommet.
Connect the red wire to the Charger Board’s
“BAT+” connector, and the black wire to the “–
BAT” connector (Fig. 44).
Refit the light diffuser and main cover.
Step 24.4 - Re-setup and Test the Opener
a.
b.
24
GDO-9v2 SecuraLift® Owner Installation Instructions
Setup travel limits and code transmitters as per the
GDO-9 instruction manual.
Press either the OPERATE button or use a transmitter
to operate the opener.
Battery Back Up Installation
Wiring diagram
4. Connect
1. Remove screws &
swing cover to open
Battery assembly (#01660)
5. Close cover and
re-secure with screw
4
9
6
10
11
5
10
3. Mount battery and
secure with item 4 & 10
8
7
1
3
2
2
3
fig 46
2. Connect wires as shown.
Refer to wiring diagram.
10
Item
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Description
SBY-3 Version 1.00
SBY-3 charger harness
SBY-3 battery harness
Pan head screw w/washer M4 x 8
Batteries cover
Batteries 12V sec 12-2.2 AGM type
Battery harness
Battery coupling wire
Batteries support
Hexagon standoff M4
e.
f.
Disconnect power to the opener.
Remove screws and swing open the cover (Fig 46).
Mount battery pack and secure with item 4 and 10.
Mount the SBY-3 Charger Board on three hex
spacers pre mounted on base and secure with
three (3) M4 x 8 screws.
Feed the 2-wire battery harness through the
grommet on the base plate and connect to SBY-3.
Feed charger harness from SBY-3 to the control
board and plug into the 4 pin connector marked
“SBY-3” onto the control board.
WARNING: After Step 25.1(g) the opener may
become active (even when power is off). This is a
result of a residual charge in the batteries.
g.
h.
1
Qty Order Code
1
00852
1
14115
1
15660
7
10320
1
16460
2
15470
1
15670
1
12005
1
16480
2
11190
Step 25.1 - Connect the Battery Back Up Kit
a.
b.
c.
d.
4
Connect battery harnesses item 3 and 7 together
(Fig 46).
Reconnect power.
Step 25.2 - Testing Battery Back Up
a.
b.
Press either the OPERATE button or transmitter
to test the opener.
Whilst door is in motion disconnect mains
power the door should continue to operate as
normal.
NOTE: Wait for the door to complete its travel.
c.
d.
Press the OPERATE button or transmitter to
activate the door.
Whilst door is in motion re-connect power. The
door should complete the cycle as normal.
Step 25.3 - Troubleshooting
If door stops or moves very slowly under battery
power, the batteries may be weak or have no
charge. Connect mains power and allow the
batteries to charge. This may take 24 - 48 hours to
reach maximum charge capacity.
Owner Installation Instructions GDO-9v2 SecuraLift®
25
Final Set Up
Step 26 - Setting of Courtesy Light Time
The preset courtesy light time is three minutes. This time
can be changed by the following:
a. Press and hold both the AUTO CLOSE TIME and
FORCE MARGIN SET buttons (Fig. 47).
b. While holding in these buttons, press the OPEN
button - each press will add 10 seconds to the
light time.
c. To decrease the time, follow Step 16(a) and press
the CLOSE button - each press will deduct 10
seconds from the light time.
d. To recall the factory set light time press and hold
together the AUTO CLOSE TIME button, the
FORCE MARGIN SET button and the SET button
for 2 seconds.
fig 47
Step 27 - Setting the Pet Mode position
fig 48
The default Pet Mode height can be changed as follows:
a. Make sure the door is closed, then press and
hold the OPEN button for six (6) seconds (Fig.
48), until you hear three beeps and the OPEN
and CLOSE LEDs flash rapidly.
b. Press the OPEN or CLOSE button to move the
door to the desired pet mode open position.
c. Press the SET button to record the new position.
When activated, Pet Mode drives the door to the preset
position from either above or below. Pet Mode’s active
status is indicated by both the OPEN and CLOSE LIMIT
LEDs being illuminated. If a Pet Mode button is pressed
while the door is moving the door will stop. If a Pet
Mode button is pressed when the door is in the Pet
position, then the door will close.
fig 49
Step 28 - Installing the Wall Mounted
Transmitter (Optional)
a.
b.
c.
d.
Remove the faceplate from the transmitter.
Affix the baseplate in a convenient wall location
that is out of reach of children and convenient
to the customer (Fig 49). Make sure the door is
visible from this location.
Replace the faceplate.
To code the transmitter, see Steps 10.1 through
10.4 on page 19.
Step 29 - Reset all Factory Defaults
a.
b.
c.
fig 50
26
GDO-9v2 SecuraLift® Owner Installation Instructions
Turn power to opener off.
Press and hold the SET Button (Fig 50).
Turn power on while holding the SET button.
Continue to hold until all LEDs are off.
»
This will not erase transmitter codes
stored in memory.
Default Settings & Specifications
Factory default settings
Default
Step
Maximum
Maximum motor run time
25 Secs.
-
-
Courtesy light time
3 Mins.
10 Secs.
4 Mins.
Obstruction force margin
8
1
20
Auto close time
0 Secs
1 Sec.
4 Mins.
Technical specifications
Power supply
230V - 240V AC 50Hz
Transformer rating
24V DC
Standby power
2.2 Watts
Motor power
100 Watts
Motor type
24V DC permanent magnet
Shuttle travel distance in the C-Rail
2.8m approx (standard)
Maximum shuttle travel distance in the C-Rail
5m (with extended C-Rail)
Maximum door opening:
5500mm (16.5m2)
3000mm
100 kg
Width:
Height:
Weight:
Minimum Clearance
(Bottom of C-Rail to highest point of door travel)
25mm
Short term peak force
800N (80kg)
Lift force
500N (50kg)
Nominal force
150N (15kg)
Receiver type
UHF 433.92 MHz AM Receiver
Receiver code storage capacity
24 x 4 button transmitter codes
Transmitter frequency
~= to 433.92 MHz
Coding type
Multi-frequency Code hopping
Number of code combinations
Over 4.29 billion random codes
Code generation
Non-linear encryption algorithm
Transmitter battery
A23 Alkaline 12 Volts
Courtesy light
Festoon style lamp
Controller fuse
10A slow blow
NOTE: Intermittent operations may occur in areas which experience very strong winds. The strong wind
puts extra pressure on the door and tracks which may in turn trigger the safety obstruction detection system
intermittently.
Owner Installation Instructions GDO-9v2 SecuraLift®
27
Parameters
Door Status Indicators
Door Opener State
OPEN LED (Green)
Open
On
Close
Opening
Beeper
On
Flashing
Closing
Flashing
Door travel stopped
Flashing
Door obstructed when opening
Flashing
Door obstructed when closing
28
CLOSE LED (Red)
Flashing
Flashing
Opener overloaded
Alternating flashes
Door in open position with AutoClose mode selected
One second flashes
Pet Mode Engaged
On
Mains power interrupted
Rapid flashes
GDO-9v2 SecuraLift® Owner Installation Instructions
Alternating flashes
On
Beeps as door moves
Parameters
Button Functions
Buttons
Function
OPERATE
Opens/Stops/Closes the door
DOOR CODE
Codes a transmitter button for operate function
LIGHT CODE
Codes a transmitter button for light function
DOOR CODE & CLOSE
Codes a transmitter button for pet mode
LIGHT CODE & CLOSE
Codes a transmitter button for vacation function
FORCE MARGIN SET & OPEN
Increases the obstruction force margin setting
FORCE MARGIN SET & CLOSE
Decreases the obstruction force margin setting
FORCE MARGIN SET (then) SET
Resets the factory default force margin settings
AUTO CLOSE TIME (then) OPEN
Increases the auto close delay time
AUTO CLOSE TIME (then) CLOSE
Decreases the auto close delay time
AUTO CLOSE TIME (then) SET
Resets the factory default auto close delay time
FORCE MARGIN SET & AUTO CLOSE TIME (then) OPEN
Each press of the PLUS (+) button increases the
light time by 10 secs.
FORCE MARGIN SET & AUTO CLOSE TIME (then)
CLOSE
Each press of the MINUS (-) button decreases the
light time by 10 secs.
FORCE MARGIN SET & AUTO CLOSE TIME (then) SET
Reloads the factory default light time
CLOSE (for 6 secs.)
Clears the door limits set positions. Limits then
need to be reset
SET & CLOSE (for 2 secs.)
Enters pet (pedestrian) position mode
SET (then power on) & hold until all LEDs are off
Deletes control parameters excluding transmitter
storage memory
DOOR CODE (then power on) & hold until all LEDs
are off
Deletes all transmitter storage memory
SET & DOOR CODE (the power on) and hold until all
LEDs are off
Deletes all control parameters and transmitter
storage memory.
SET
Re-initialises the Opener to re-calculate force
margin
Owner Installation Instructions GDO-9v2 SecuraLift®
29
Troubleshooting guide
Symptom
Possible cause
Remedy
Door will not operate
Mains power not switched on
Switch on mains power
Door is obstructed
Remove obstruction
Door is locked or motor jammed
Unlock door or remove jam
Door tracks/hardware damaged
Door requires service/repair by
qualified technician
Adverse weather conditions (wind
or cold) causing door to stiffen and
become tight in the tracks
Increase force margin setting.
See Step 18 on page 20
Door starts to close but
automatically reverses to
open position
Possible obstruction in
the doorway
Gate operates from drive unit
(operate) button but not from
transmitter.*
Transmitter code not stored
in memory
Flat battery
*See note
Remove obstruction
Code transmitter into opener’s
memory. Refer Step 19.1 on page
21
Replace battery
Door will not close fully
Door limits position need to
be reset
Reset limits positions. Refer Step
16.3 on page 18
Door will not open fully
Door limits position need to
be reset
Reset limits positions. Refer Step
16.3 on page 18
Courtesy light not working
Faulty light
Replace lamp
Auto close not working
PE Beam or wiring faulty
Repair P.E. Beam or replace wiring
PE Beam not aligned correctly
Re-align optics. See P.E.
instructions
PE Beam is obstructed
Remove obstruction from the path
of P.E. Beam
Door obstructed when closing
Remove obstruction
Auto close time not set
See Step 23 on page 23
PLEASE NOTE:
Some areas may be prone to excessive radio interference brought on by devices such as cordless telephones,
wireless stereo headphones and baby monitors. It is possible that these devices could cause a degree of
interference such as to greatly reduce the range of the transmitter. In such an instance please contact your ATA
dealer for an alternative frequency replacement kit. As this is not a warrantable situation but an environmental
issue charges may apply for the changeover.
30
GDO-9v2 SecuraLift® Owner Installation Instructions
Maintenance
Maintenance
Yearly
Whilst your opener does not require any periodic
maintenance, the door that it is fitted to does.
Your garage door is a large, heavy, moving object
and should be tested regularly to ensure it is in
good condition. A poorly maintained door could
cause fatal or serious injuries or serious damage to
property.
Automatic Technology suggests you contact your
installer to perform an annual door service.
To ensure a long and trouble free life for your opener
the following is recommended:
Monthly
•
•
Disengage the opener and manually operate
the door: The door must be smooth to operate
by hand. An operating force on the bottom rail
should not exceed 150N (15kg) force.
Each month check that the opener reverses
when the door contacts a 40mm high object
placed on the floor (AS3350).
CAUTION: Frequently examine door, particularly
cables, springs and mountings for signs of wear,
damage or imbalance. Do not use if repair
or adjustment is needed since a fault in the
installation or an incorrectly balanced door may
cause injury. (AS3350)
Adjustments should only be carried out by
experienced persons, as this function can
be dangerous if not performed under strict safety
procedures.
WARNING! Failure to maintain your garage
door may void the warranty on your garage door
opener.
•
NOTE: If the door does not operate smoothly, call
your installer.
Service Record
Record any maintenance in the following table to assist in any warranty service.
Date
Service by
Signature
Invoice No.
Amount
Owner Installation Instructions GDO-9v2 SecuraLift®
31
Parts Listing
32
GDO-9v2 SecuraLift® Owner Installation Instructions
Owner Installation Instructions GDO-9v2 SecuraLift®
33
Warranty and Exclusion of Liability
1. This warranty is an addition to any non-excludable conditions or warranties that are implied into this contract
by relevant statute, including the Trade Practices Act 1974 (Cwth).
2. Subject to all of the matters set out below, Automatic Technology Australia Pty Ltd (“ATA”) warrants:
(a) overhead door opener drive units for twenty four (24) months or 5000 cycles, whichever occurs first; and
(b) all components and accessories for twelve (12) months, from the date of purchase (specified in the sales
docket receipt) as free of any defects in material and workmanship.
3. This warranty applies only where the purchaser:
(a) immediately notifies ATA or the retailer of the alleged defect;
(b) returns the product to the retailer; and
(c) presents the relevant sales docket and this warranty document to the retailer to confirm the date
of purchase.
4. Except for this warranty, ATA gives no warranties of any kind whatsoever (whether express or implied),
in relation to the product, and all warranties of whatsoever kind relating to the product are, to the extent
permissible by statute, hereby excluded.
5. To the extent permissible by statute, ATA disclaims any liability of whatsoever nature in respect of any claim
or demand for loss or damage which arises out of:
(a) accidental damage to or normal wear and tear to the product or to the product’s components;
(b) any cost relating to damage resulting from wear and tear;
(c) blown fuses, loss or damage caused by electrical surges, power surges or power spikes;
(d) loss or damage due to theft, fire, flood, rain, water, lightning, storms or any other acts of God;
(e) maximum continuous operating time exceeding one (1) minute in ten (10);
(f) maximum operating force exceeding *20kg (200N) when moving the door manually to the open or
closed position;
(g) door surface area and/or weight exceeding 16.5m2 and 100kg respectively;
(h) door not in safe and correct working order and condition;
(i) evidence of unauthorised repairs;
(j) any cost relating to damage caused by misuse, negligence or failure to maintain the equipment in a
proper working order as per clauses (d) through (h);
(k) installation, adjustment or use which is not in accordance with the instructions set out in installation
instruction manual
(l) attempted or complete modification or repairs to the product carried out by a person who is not
authorised or has not been trained by ATA to carry out such modification or repairs;
(m) faulty or unsuitable wiring of structure to which the product is fixed or connected;
(n) radio (including citizen band transmission) or any electrical interference;
(o) damage caused by insects;
(p) loss or damage to any property whatsoever or any loss or expense whatsoever resulting or arising there
from or any consequential loss;
(q) any cost or expense arising due to manufacturer recall of any product;
(r) any cost or expense due to negligence of the approved service provider;
(s) installation of a residential garage door opener in a commercial or industrial situation or a non-single
residential dwelling.
6. ATA’s liability under this warranty is limited, at ATA’s absolute option, to replacing or repairing the product
which ATA, in its unfettered opinion, considers to be defective either in material and/or workmanship or to
credit the dealer with the price at which the product was purchased by the dealer.
7. This warranty does not extend to cover labour for installation.
8. This warranty is limited to Return-to-Base (RTB) repair and does not cover labour for on-site attendance.
9. This warranty is void if the Product is not returned to the manufacturer in original or suitably secure packaging.
10. This warranty is only applicable for repairs to the product carried out within Australia.
11. This warranty does not cover consumable items including globes, batteries and fuses.
12. This warranty is not transferable.
13. Where the Product is retailed by any person other than ATA, except for the warranty set out above, such
person has no authority from ATA to give any warranty or guarantee on ATA’s behalf in addition to the
warranty set out above.
NOTES:
1. One (1) cycle = one (1) open and one (1) close action of the door or gate.
2. This warranty is to be read in conjunction with the owner’s copy of the installation instruction manual.
3 *The door should be balanced in such a way that the user manually is able to open or close the door without using
force not greater than 150N (15kg ) although a greater force may be required for the start of the movement.
34
GDO-9v2 SecuraLift® Owner Installation Instructions
Owner Installation Instructions GDO-9v2 SecuraLift®
35
© January 2008 Automatic Technology (Australia) Pty Ltd. All rights reserved. TrioCode™ and SecuraLift ® are trademarks
of Automatic Technology (Australia) Pty Ltd. No part of this document may be reproduced without prior permission. In an
ongoing commitment to product quality we reserve the right to change specification without notice. E&OE.
Automatic Technololgy (Australia) Pty Ltd
ABN 11 007 125 368
6-8 Fiveways Boulevard
Keysborough, Victoria, 3173, Australia
P 1300 133 944
+61 2 9722 5666 (International Enquiries Only)
E sales@ata-aust.com.au
www.ata-aust.com.au
GARAGE DOOR OPENERS | GATE OPENERS | REMOTE CONTROL ACCESS SOLUTIONS
Download PDF