Digital Monitoring Products | 7063A | Installation guide | Digital Monitoring Products 7063A Installation guide

Installation Guide
XR500 Series
Command Processor™ Panel
MODEL XR500, XR500N, XR500E
COMMAND PROCESSOR
INSTALLATION GUIDE
 
FCC NOTICE
This equipment generates and uses radio frequency energy and, if not installed and used properly in strict accordance
with the manufacturer’s instructions, may cause interference with radio and television reception. It has been type tested
and found to comply with the limits for a Class A computing device in accordance with the specification in Subpart J
of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential
installation. If this equipment does cause interference to radio or television reception, which can be determined by
turning the equipment off and on, the installer is encouraged to try to correct the interference by one or more of the
following measures:
Reorient the receiving antenna
Relocate the computer with respect to the receiver
Move the computer away from the receiver
Plug the compute into a different outlet so that computer and receiver are on different branch circuits
If necessary, the installer should consult the dealer or an experienced radio/television technician for additional suggestions.
The installer may find the following booklet, prepared by the Federal Communications Commission, helpful:
“How to identify and Resolve Radio-TV Interference Problems.”
This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402
Stock No. 004-000-00345-4
© 2003-2010 Digital Monitoring Products, Inc.
Information furnished by DMP is believed to be accurate and reliable.
This information is subject to change without notice.
Table of Contents
Product Specifications Summary
1.1
1.2
1.3
1.4
1.5
1.6
1.7
Power Supply..........................................................................1
Communication.......................................................................1
Panel Zones............................................................................1
Keypad Bus.............................................................................1
LX-Bus™.................................................................................1
Outputs..................................................................................1
Enclosure Specifications...........................................................1
Panel Features
2.1
2.2
2.3
2.4
2.5
2.6
2.7
Description..............................................................................2
Zone Expansion.......................................................................2
Output Expansion....................................................................2
Central Station Communication.................................................2
Encrypted Communications (XR500N/XR500E only)....................2
Caution Notes.........................................................................3
Compliance Instructions...........................................................3
System Components
3.1
3.2
3.3
3.4
3.4
Description..............................................................................3
Wiring Diagram.......................................................................4
Lightning Protection.................................................................5
Accessory Devices...................................................................5
Accessory Devices (continued)..................................................6
Installation
4.1
4.2
Mounting the Enclosure............................................................7
Mounting Keypads and Zone Expansion Modules........................8
Primary Power Supply
5.1
5.2
AC Terminals 1 and 2...............................................................9
Transformer Types...................................................................9
Secondary Power Supply
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
Battery Terminals 3 and 4......................................................10
Earth Ground (GND)..............................................................10
Battery Only Restart..............................................................10
Battery Replacement Period...................................................10
Discharge/Recharge...............................................................10
Battery Supervision................................................................10
Battery Cutoff........................................................................10
XR500 Series Power Requirements..........................................11
Standby Battery Selection......................................................13
Bell Output
7.1
Terminals 5 and 6..................................................................14
Keypad Bus
8.1
8.2
8.4
8.5
8.6
8.7
Description............................................................................14
Terminal 7 - RED...................................................................14
Terminal 9 - GREEN...............................................................14
Terminal 10 - BLACK..............................................................14
J8 Programming Connection...................................................14
OVC LED...............................................................................14
Smoke and Glassbreak Detector Output
9.1
9.2
Terminals 11 and 12..............................................................14
Current Rating.......................................................................14
Protection Zones
10.1
10.2
10.3
10.4
Terminals 13–24....................................................................15
Operational Parameters..........................................................15
Zone Response Time..............................................................15
Keyswitch Arming Zone..........................................................15
XR500 Series Installation Guide
Digital Monitoring Products
i
Table of Contents
Powered Zones for 2-Wire Smoke Detectors
11.1
11.2
Terminals 25–26 and 27–28...................................................15
Compatible 2-Wire Smoke Detector Chart................................16
Dry Contact Relay Outputs
12.1
12.2
12.3
Description............................................................................17
Contact Rating......................................................................17
Model 431 Output Harness Wiring...........................................17
Annunciator Outputs
13.1
13.2
13.3
Description............................................................................17
Model 300 Harness Wiring......................................................17
Model 860 Relay Module........................................................17
J23 6-Pin Header
14.1
Description............................................................................18
J22 LX-Bus Expansion Connector
15.1
15.2
15.3
15.4
15.5
Description............................................................................18
J22 LX-Bus Header................................................................18
LX-Bus Interface Cards...........................................................19
LX-Bus LEDs..........................................................................19
OVC LED...............................................................................19
J21 Serial Connector
16.1
16.2
16.3
16.4
Description............................................................................19
Computer Connection to J21..................................................19
Direct iCOM Connection to J21...............................................20
Serial Connector LEDs............................................................20
J1 Ethernet Connector (XR500N/XR500E only)
17.1
17.2
Description............................................................................20
Ethernet LEDs.......................................................................20
J3 Telephone RJ Connector
18.1
18.2
18.3
18.4
18.5
Description............................................................................20
J10 893A Connector...............................................................20
Notification...........................................................................20
Phone Line Monitor................................................................20
FCC Registration....................................................................21
Reset and Tamper Headers
19.1
19.2
J16 Reset Header .................................................................22
J4 Tamper Header ................................................................22
Listed Compliance Specifications
20.1 Introduction..........................................................................23
Universal Burglary Specifications
21.1 21.2
21.3
21.4
21.5
21.6
21.7
21.8
21.9
21.10
21.11
21.12
Introduction..........................................................................23
Wiring..................................................................................23
Control Outside of Protected Area...........................................23
Police Station Phone Numbers................................................23
Bypass Reports......................................................................23
System Maintenance..............................................................23
Listed Receivers....................................................................23
Power Supply Supervision......................................................23
Wireless Tamper....................................................................23
Wireless External Contact.......................................................23
Wireless Supervision Time......................................................23
Detect Wireless Jamming.......................................................23
Digital Monitoring Products
ii
XR500 Series Installation Guide
Table of Contents
Area Information
22.1
22.2
22.3
22.4
22.5
Ownership............................................................................24
Annunciation.........................................................................24
Trouble Display......................................................................24
Closing Wait..........................................................................24
Local Bell Supervision............................................................24
Household Burglar-Alarm System Units
ANSI/UL 1023
23.1
23.2
23.3
23.4
23.5
23.6
23.7
Audible Devices.....................................................................24
Auxiliary Circuits....................................................................24
Bell Cutoff.............................................................................24
Entry Delay...........................................................................24
Exit Delay.............................................................................24
Weekly Test...........................................................................24
Wireless Audible Annunciation Option.....................................24
Central-Station and Proprietary Burglar-Alarm Units
ANSI/UL 1610 AND ANSI/UL 1076
24.1 Opening/Closing Reports........................................................24
24.2 Closing Wait..........................................................................24
24.3 Entry Delay...........................................................................24
24.4 Exit Delay.............................................................................25
24.5 Proprietary Dialer..................................................................25
24.6 DACT Central Station.............................................................25
24.7 Bell Cutoff.............................................................................25
24.8 Standard or Encrypted Line Security.......................................25
24.9 Wireless Audible Annunciation Option.....................................25
24.10 Model 463G or CellCom, CELL Only, Standard or
Encrypted Line Security ...............................................................25
24.11 Model 463G or CellCom, NET with CELL as Alternate
Primary and Dialer Backup, Standard or Encrypted Line Security .....26
24.12 Model 463G or CellCom, NET with CELL as Backup and
Adaptive Primary, Standard or Encrypted Line Security ...................26
Holdup Alarm Units
ANSI/UL 636
25.1
25.2
25.3
25.4
25.5
25.6
25.7
25.8
ANSI/UL 1610 Required.........................................................27
1100X Wireless Receiver........................................................27
Wireless Supervision Time......................................................27
LED Display...........................................................................27
Jamming Detection................................................................27
Local Alarm...........................................................................27
Message to Transmit..............................................................27
Wireless Audible Annunciation Option.....................................27
Digital Burglar Alarm Communicator System Units
ANSI/UL 1635
26.1
26.2
26.3
26.4
System Trouble Display..........................................................27
Digital Dialer Telephone Number.............................................27
Test Time..............................................................................27
Closing Wait..........................................................................27
Police Station Connected and Local Burglar Alarm Units
ANSI/UL 365
27.1
27.2
27.3
27.4
27.5
27.6
System Trouble Display..........................................................27
Entry Delay...........................................................................27
Exit Delay.............................................................................27
Bell.......................................................................................28
Bell Cutoff.............................................................................28
Automatic Bell Test................................................................28
XR500 Series Installation Guide
Digital Monitoring Products
iii
Table of Contents
27.7 Standard or Encrypted Line Security.......................................28
27.8 Wireless Audible Annunciation Option.....................................28
27.9 Model 463G or CellCom, CELL Only, Standard or Encrypted
Line Security ...............................................................................28
27.10 Model 463G or CellCom, NET with CELL as Alternate Primary
and Dialer Backup, Standard or Encrypted Line Security .................29
27.11 Model 463G or CellCom, NET with CELL as Backup and
Adaptive Primary, Standard or Encrypted Line Security ...................29
Police Station Connected and Local Burglar Alarm Units
ANSI/UL 609
28.1
28.2
28.3
28.4
28.5
28.6
28.7
Mercantile.............................................................................29
Entry Delay...........................................................................29
Exit Delay.............................................................................29
Mercantile Safe and Vault.......................................................30
Bell.......................................................................................30
Bank Safe and Vault (XR500N/XR500E only)............................30
Wireless Audible Annunciation Option.....................................30
Access Control System Units
ANSI/UL 294
29.1
29.2
29.3
Panel Designation..................................................................30
Tamper Protection.................................................................30
Compatible Devices...............................................................30
Universal Fire Alarm Specifications
30.1
30.2
30.3
30.4
30.5
30.6
30.7
30.8
30.9
30.10
30.11
30.12
Introduction..........................................................................31
Wiring..................................................................................31
Transformer..........................................................................31
End-of-Line Resistor...............................................................31
System Trouble Display..........................................................31
Fire Display...........................................................................31
Police Station Phone Number..................................................31
System Maintenance..............................................................31
Audible Alarm........................................................................31
Fire Zone Programming..........................................................31
Class A Style D Zones............................................................31
Listed Receivers....................................................................31
Control Units for Fire-Protective Signaling Systems
ANSI/UL 864, NFPA 72
31.1 Power Supply........................................................................32
31.2 Zone Restoral Reports............................................................32
31.3 Power Fail Delay....................................................................32
31.4 Sprinkler Supervisory.............................................................32
31.5 DACT Systems.......................................................................32
31.6 Local Protective Signaling Systems..........................................33
31.7 Remote Station Protective Signaling Systems...........................33
31.8 Fire Protective Signaling Systems using
Internet/Intranet/Cell Networks.....................................................33
31.9 Combination Systems.............................................................33
31.10 Remote Annunciators.............................................................33
31.11 Notification Appliances ..........................................................34
31.12 Cross Zoning...........................................................................34
31.13 Ground Fault...........................................................................34
31.14 Wireless Testing......................................................................34
Household Fire Warning System Units
ANSI/UL 985, NFPA 72
32.1
32.2
32.3
32.4
Bell Output Definition.............................................................34
Audible Devices.....................................................................34
Auxiliary Circuits....................................................................34
Bell Cutoff.............................................................................34
Digital Monitoring Products
iv
XR500 Series Installation Guide
Table of Contents
32.5
32.6
32.7
32.8
Detect Wireless Jamming.......................................................34
Wireless External Contact.......................................................34
Wireless Supervision Time......................................................34
Wireless Fire Verification........................................................34
California State Fire Marshal Specifications
33.1
Bell Output Definition.............................................................35
New York City (MEA) Specifications
34.1
34.2
34.3
34.4
34.5
Introduction..........................................................................35
Digital Dialer and Network Communication..............................35
Wiring..................................................................................35
Communication Programming.................................................35
Additional Requirements........................................................35
False Alarm Reduction Programmable Options *
35.1 Shipping Defaults and Recommended Programming for
ANSI/SIA CP-01-2000...................................................................36
35.2 Call Waiting (ANSI/SIA CP-01-2000).......................................37
35.3 Occupied Premise (ANSI/SIA CP-01-2000)...............................37
35.4 Entry Delay (ANSI/SIA CP-01-2000)........................................37
35.5 Minimum Installation Requirements (ANSI/SIA CP-01-2000).....37
ULC S304 Specifications
36.1
Level V Communication..........................................................37
Wiring Diagrams
37.1 866 with NAC Extender .........................................................38
37.2 866 Class B Style W using Single Notification Appliance............39
37.3 866 Class B Style W Multiple Notification Appliance Circuit........40
37.4 866 Class B Style W Dual Notification Appliance Circuits...........41
37.5 865 Class B Style W using Single Notification Appliance............42
37.6 865 Class B Style W Multiple Notification Appliance Circuit........43
37.7 865 Class B Style W Dual Notification Appliance Circuits...........44
37.8 865 Class A Style X using Single Notification Appliance.............45
37.9 867 Class B Style W using Single Notification Appliance............46
37.10 867 Class B Style W Multiple Notification Appliance Circuit........47
37.11 867 Class B Style W Multiple Notification Appliance Circuits......48
37.12 Panel Slave Communicator for FACP using 630F Annunciator....49
37.13 Panel Slave Communicator for FACP using Outputs..................50
37.14 Dual Style D Zone Module Installation.....................................51
37.15 Derived Channel Installation Using Bosch D8122......................52
37.16 Rothenbuhler 5110 High Security Bell Wiring...........................53
37.17 LX-Bus™ Module Connection..................................................54
37.18 Model 860 Relay Module Connection.......................................55
37.19 Powered Burglary Devices........................................................55
Revisions to This Document
Listings and Approvals
XR500 Series Installation Guide
Digital Monitoring Products
v
Introduction
Product Specifications Summary
1.1
Power Supply
Transformer Input:
Model 327, plug-in — Primary input: 120 VAC, 60 Hz, Secondary output: 16.5 VAC 50 VA
Model 322, wire-in — Primary input: 120 VAC, 60 Hz, Secondary output: 16 VAC 56 VA
Standby Battery: 12 VDC, 1.0 Amps Max. charging current
Models 365, 366, 367, 368, or 369
Replace every 3 to 5 years
* Auxiliary: 12 VDC output at 1.5 Amp Max
* Bell Output: 12 VDC at 1.5 Amp Max
Note: The combined Auxiliary and Bell outputs total cannot exceed 3 Amps with a 50 VA or 56 VA Transformer.
All circuits are inherent Power Limited except the red battery wire and AC terminal.
* For Commercial Fire installations, see the Compliance Instructions section.
1.2
Communication
Built-in network communication to DMP Model SCS-1R Receivers (XR500N/XR500E only)
Built-in encrypted communication to iCOM-E™ Encrypted Network Alarm Router (XR500E only)
Built-in dialer communication to DMP Model SCS-1R Receivers
Built-in Contact ID communication to non-DMP receivers
Optional 893A Dual Phone Line Module with phone line supervision
Can operate as a local panel
1.3
Panel Zones
Eight 1k Ohm EOL burglary zones (zones 1 to 8)
Two 3.3k Ohm EOL powered zone with reset (zones 9 and 10)
1.4
Keypad Bus
You can connect up to 16 of the following supervised keypads and expansion modules to the keypad bus:
• Alphanumeric keypads
• Four- and/or single-zone expansion modules
• Single-zone detectors
• Access control modules
1.5
LX-Bus™
You can connect the following devices to the LX-Bus™ provided on the panel or by the DMP 481, 462N, 462P and 472
Interface Cards up to the maximum number of LX-Bus™ addresses. See Accessory Devices in section 3.4.
• Four- and/or single-zone expansion modules
• Single-zone detectors
• Relay output expansion modules
• Graphic annunciator modules
1.6
Outputs
The XR500 Series provide two Single Pole, Double Throw (SPDT) relay outputs which require the installation of two
Model 305 relays, each rated 1 Amp at 30 VDC resistive (power limited sources only). A Model 431 Output Harness is
required to use these outputs.
The XR500 Series panels also provide four open collector outputs rated for 50mA each. The open collector outputs
provide ground connection for a positive voltage source. A Model 300 Output Harness is required to use these
outputs.
1.7
Enclosure Specifications
The XR500 Series panels are shipped in an enclosure with a transformer, End-of-Line resistors, battery leads, user’s
guide, and programming sheets.
Enclosure
Model
Size
Color(s)
Construction (Cold Rolled
Steel)
350
17.5”W x 13.5”H x 3.5”D
Gray (G) or Red (R)
18-Guage
350A
17.5”W x 13.5”H x 3.75”D
Gray (G)
18-Guage with 16-Guage door
341
12.75”W x 6.55”H x 2.9”D
Gray (G)
20-Guage
352X
14.5”W x 32.0”H x 4.0”D
Gray (G)
16-Guage
XR500 Series Installation Guide
Digital Monitoring Products
1
Introduction
Panel Features
2.1
Description
The DMP XR500 Series Command Processor™ Panel is a versatile 12 VDC, combined access control, burglary, and fire
communicator panel with battery backup. The XR500 Series provides eight on-board burglary zones and two on-board
12 VDC Class B powered zones. The powered zones have a reset capability to provide for 2-wire smoke detectors,
relays, or other latching devices. The XR500 Series can communicate to one or two DMP SCS-1R Receivers using
digital dialer or network communication, or to non-DMP receivers using the Contact ID format.
2.2
Zone Expansion
Up to 574 additional zones are available on the XR500 Series using DMP LCD keypad remote zone capability and
zone expansion modules. The panel keypad data bus supports up to sixteen supervised device addresses with each
address supporting up to four programmable expansion zones.
Up to 500 zones are available using the on board LX-Bus, Model 461 Interface Adaptor with 481, 462N, 462P, 463G,
and 472 Interface Cards, and any combination of single, four, eight, or 16-zone expansion modules and single-zone
LX‑Bus™ detectors.
Note: Do not use shielded wire for LX-Bus or Keypad Bus circuits.
2.3
Output Expansion
In addition to the two SPDT relays and four programmable open collector outputs on the XR500 Series, you can also
connect up to 25 programmable Model 716 Output Expansion Modules to each LX-Bus. These modules can provide an
additional 500 programmable SPDT relays.
The XR500 Series provides 100 Output Schedules you can use for programming the 716 to perform a variety of
annunciation and control functions. You can also assign the 716 outputs to any panel Output Options such as Fire
Alarm, Communication Fail, or Phone Trouble Outputs. Refer to the 716 Installation Guide (LT-0183).
The LX-Bus™ also supports the Model 717 Graphic Annunciator Module. Each 717 module supplies 20 switched ground
outputs that follow the state of their assigned zones.
Note: The 717 supports the first eight Keypad Bus addresses. To follow Keypad Bus addresses nine through 16, install
multiple 716 modules. Refer to the 717 Installation Guide (LT-0235) and 716 Installation Guide (LT‑0183).
2.4
Central Station Communication
You can program the XR500 Series panel for reporting to DMP SCS‑1R Receivers using digital dialer or network
communication. The panel can also communicate to non-DMP receivers using the Contact ID communication
format. The XR500 Series connects at the premises to a standard RJ31X or RJ38X telephone jack. Use the DMP 893A
Dual Phone Line Module when connecting the XR500 Series panel to two separate phone lines in fire or burglary
applications.
2.5
Encrypted Communications (XR500N/XR500E only)
An XR500E panel communicates using AES encryption. If you currently have an XR500N panel installed, you may
contact DMP Customer Service with the panel serial number. The serial number(s) should be sent in writing via
e-mail or fax. A separate feature key is sent for each panel to activate encrypted communications using the Feature
Upgrade process. Encrypted communication cannot be enabled on a standard XR500 panel. For more information on
the Feature Upgrade process see the XR500 Series Programming Guide (LT-0679).
Digital Monitoring Products
2
XR500 Series Installation Guide
Introduction
2.6
Caution Notes
Throughout this guide you will see caution notes containing information you need to know when installing the panel.
These cautions are indicated with a yield sign. Whenever you see a caution note, make sure you completely read
and understand its information. Failing to follow the caution note can cause damage to the equipment or improper
operation of one or more components in the system. See the example shown below.
2.7
Always ground the panel before applying power to any devices: The XR500 Series must be properly
grounded before connecting any devices or applying power to the panel. Proper grounding protects
against Electrostatic Discharge (ESD) that can damage system components.
Compliance Instructions
For applications that must conform to a local authorities installation standard or a National Recognized Testing
Laboratory certificated system, please see the Wiring Diagrams for Notification Appliances and the Listed Compliance
Specifications section near the end of this guide for additional instructions.
System Components
3.1
Description
The DMP XR500 Series system is made up of an alarm panel with a built-in communicator, an enclosure, battery,
one 16.5 VAC transformer, and keypads. You can use up to sixteen supervised 32-character LCD keypads; network
communications and expansion interface cards; zone and output expansion modules; and initiating and indicating
circuit modules. You can also connect auxiliary devices to the panel’s output relays to expand the basic system
control capability. Combined current requirements of additional modules may require an auxiliary power supply.
Refer to the XR500 Series Power Requirements section in this guide when calculating power requirements.
XR500 Series Installation Guide
Digital Monitoring Products
3
Introduction
3.2
Wiring Diagram
The XR500 Series diagram below shows some of the accessory modules you can connect for use in various
applications. A brief description of each module follows in section 3.4.
s
Suitable for manual fire alarm,
automatic fire alarm, sprinkler
supervisory, or water flow
alarm.
SIA CP-01-2000 minimum
system is XR500, listed local
Bell, and off premise DACT
communication to an SCS-1R
receiver plus listed compatible
keypads as indicated in the
installation guide.
K7
RED
BLACK
Cold Water
Pipe Earth
Ground
For Standard Line
Security burglary
applications use
Ademco Model
AB12M bell and bell
housing.
Bell
s
1k
Ohm
RED
Ground
Bell cutoff time
range is 5 to 99
minutes, non-coded.
s
s
S
15 16
S
S
S
S
1k
1k
Ohm Ohm
17
S
18 19
S
S
1k
1k
Ohm Ohm
20
S
S
21 22
S
23
S
S
1k
1k
Ohm Ohm
S
26
27
Zone
9
S
S
28
Zone
10
S
S
S
Zone Expander
Model 715
7mA @ 12 VDC
Models 715-8, 715-16
20mA @ 12 VDC
BLACK
s
s
s
s
s
s
s
s
s
s
Zone Expander
Model 714
7mA @ 12 VDC
Models 714-8, 714-16
20mA @ 12 VDC
Zone
Expander
Model 711
7mA @ 12
VDC
Zone Expander
(up to 8 zones)
Model 712-8
19mA @ 12
VDC
Smoke
Detector
DISARM
ARM
S
S
S
S
S
1k Ohm 1k Ohm 1k Ohm
Use Listed Power Supervision
Relay rated at 12 VDC.
S
S
S
S
S
S
S
S
3.3k Ohm 3.3k Ohm 3.3k Ohm 3.3k Ohm
S
1k Ohm 1k Ohm 1k Ohm
Using verification delays
on zones 9 and 10 is
optional. Use the
delays marked on the
smoke detectors.
s = Supervised Circuit
RED
YELLOW
GREEN
Keyswitch Arming
can be connected
to any zone.
Zones 9, 10, and all
expanded zones are
suitable for Class B (as
applicable for the
initiating and signaling
line circuits per ANSI/UL
864 Table 48.2 or 48.3).
Installation limits under
local Authority Having
Jurisdiction (AHJ).
3.3k
3.3k
Ohm
Ohm
Resistor Resistor
Auxiliary Power
Total current combined from
terminals 7, 11, 25, and 27
1.5 Amp Max
10.2 VDC to 14.0 VDC
RED
S
1k
1k
Ohm Ohm
Minimum voltage on Auxiliary output
to process Sensor trips is 10.2 VDC.
s s
J16
Reset
24 25
Zone 8
14
Zone 7
12 13
Zone 5
11
Zones 9 and 10 and
Model 715 compatibility
identifier: A
Maximum operating
range: 9.7 VDC to
14.0 VDC.
Class B (Style A).
Z7 GND Z8 Z9+ Z9– Z10+ Z10–
Zone 6
10
Z3 GND Z4 Z5 GND Z6
Zone 2
s
9
Zone 1
s
8
22 gauge minimum
s
16 to 18 gauge wire
Maximum AC Wire distance
with 16 gauge wire: 70 feet s
with 18 gauge wire: 40 feet
7
22 gauge minimum
6
BLACK
5
22 gauge minimum
4
GREEN
3
22 gauge minimum
2
YELLOW
1
Listed Resistors
1.0k Ohm - DMP Model 311
3.3k Ohm - DMP Model 309
10K Ohm - DMP Model 308
J11
Heat detectors, pull
stations, or any other
contact devices listed
for Fire Protective
Signaling can be
connected to zones
9 and 10.
Outputs 3-6
AC AC +B –B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
s
3
4
5
6
Zone 3
K6
J8
PROG
Suitable for Household Fire
and Household Burglary.
Suitable for Coded and March
Time signaling.
J2
Zone 4
J10
Suitable for Standard or
Encrypted Central Station with
NET or CELL communication.
Suitable for Bank Safe and
Vault Service with 350A
Enclosure.
¼"
Output 1 OVC Output 2
Out1 Out2
L
X
Battery
Start
Central Station DACT service
may be provided using 350A
Attack Resistant enclosure.
Suitable for Signaling and
Remote Station PPU DACT
Service.
RS-232
J22
LX-Bus
Rear
Tamper
Annunciator Outputs (J11)
Output Color Code
Output 3
Red
Output 4
Yellow
Output 5
Green
Output 6
Black
s
J21
Power J23
R
LED
The plug-in transformer shall plug
into a 120 VAC 60 Hz outlet not
controlled by a switch and all 16 to
18 gauge wire shall run through
conduit.
Suitable for Proprietary, PPU,
other technologies, local.
Wiring on terminals 5 through 22 must
exit right and maintain 1/4" separation
from the AC and battery positive wiring.
J1 s
Ethernet
Bell
12 VDC
Minimum cutoff time 5 min.
1.5 Amp Max
s
Form C Relays (J2)
Output Color Code–Model 431 Harness
Output 2 N/O Orange/White
Output 2 Com White/Gray
Output 2 N/C Violet/White
Output 1 N/O Orange
Output 1 Com Gray
Output 1 N/C Violet
AC Wiring must be in conduit and exit
out the left side of the enclosure.
J4
Tamper
Link LED
Activity LED
USE MARKING
Commercial and Residential Fire,
Burglar, Holdup, and Access Protected
Premise Unit
Suitable for Local, Police
Station Connect, Mercantile,
and Proprietary with 350A
Enclosure.
XR500 Series
Command Processor™
Panel
J3 s
Phone Line
HOUSEHOLD FIRE WARNING
Recognized limited energy cable must
be used for connection of all initiating,
indicating, and supplementary devices.
TYPES OF SERVICE
Front and Rear
tamper protection
included with
Model 350A
Attack Resistant
Enclosure.
Front
Tamper
s
NFPA 72 OPERATING
INSTRUCTIONS
The operating instructions should be
located adjacent to the control unit or
keypad.
S
S
S
1k Ohm
WARNING: Incorrect
connections may cause
damage to the unit.
S
1k Ohm
CAUTION: DO NOT USE LOOPED WIRE
UNDER TERMINALS. BREAK WIRE RUN TO
PROVIDE SUPERVISION OF CONNECTIONS.
1k Ohm
WARNING
THIS UNIT MAY BE PROGRAMMED TO USE AN ALARM VERIFICATION FEATURE THAT
RESULTS IN DELAY OF THE SYSTEM ALARM SIGNAL FROM THE INDICATED CIRCUITS.
THE TOTAL DELAY (CONTROL UNIT PLUS SMOKE DETECTORS) SHALL NOT EXCEED 60
SECONDS. NO OTHER SMOKE DETECTOR SHALL BE CONNECTED TO THESE CIRCUITS
UNLESS APPROVED BY THE LOCAL AUTHORITY HAVING JURISDICTION (AHJ).
Figure 1: XR500 Series Wiring Diagram
Digital Monitoring Products
4
XR500 Series Installation Guide
Introduction
3.3
Lightning Protection
Metal Oxide Varistors and Transient Voltage Suppressors help protect against voltage surges on XR500 Series input
and output circuits. Additional surge protection is available by installing the DMP 370 or 370RJ Lightning Suppressors.
3.4
Accessory Devices
Interface Adaptor and Interface Cards
461 Interface Adaptor Card
Allows you to connect two or more expansion interface cards to the XR500 Series panel.
The 461 is an expansion mother board that plugs into the panel J6 Interface Connector and
is required when using two or more Interface Cards. Use combinations of Interface Cards
for expanding zones, network interfacing, local printing, and connecting wireless devices.
462N Network Interface Card
Allows you to connect the XR500 Series to any compatible data network and use its
communication capability in place of standard dial out telephone lines. The 462N also
provides an LX-Bus™ for connecting zone and output expansion modules to the panel.
462P Printer Interface Card
Allows you to connect the XR500 Series to any compatible serial printer providing the user
with real-time event recording. The 462P also provides an LX-Bus™ for connecting zone and
output expansion modules.
463G Digital Cellular
Communicator Card
Allows you to connect the XR500 Series to any compatible GPRS/SMS network and use its
communication in place of standard dial out lines. The 463G also provides an LX-Bus™ for
connecting zone and output expansion modules to the panel.
472 Wireless Interface Card
Provides one LX-Bus for connecting up to 200 wireless or hardwired zone expansion
modules.
481 Expansion Interface Card
Provides one LX-Bus for connecting up to 100 zone and output expansion modules.
Expansion Modules
710/710F Bus Splitter/Repeater
Allows you to increase keypad or LX-Bus™ wiring distance to 2500 feet. Model 710F is for
24 VDC applications.
711 Single Point Zone Expanders
Provides one Class B zone for connecting burglary devices.
714, 714-8, 714-16 Zone
Expanders
Provides Class B zones for connecting burglary and non-powered fire devices. 712-8 Zone Expander
Provides Class B zones for connecting burglary devices.
715, 715-8, 715-16 Zone
Expanders
Provides 12 VDC Class B powered zones for connecting smoke detectors, glassbreak
detectors, and other 2- or 4-wire devices.
725 Zone Expanders
Provides 24 VDC Class B powered zones for connecting smoke detectors, glassbreak
detectors, and other 2- or 4-wire devices. Requires 710F Bus Splitter/Repeater.
716 Output Expander
Provides four Form C relays (SPDT) and four switched grounds (open collector) for use in a
variety of remote annunciation and control applications for use on the LX-Bus only.
717 Graphic Annunciator Module
Provides 20 zone following annunciator outputs (open collector) for use in a variety of
remote annunciation and control applications for use on the LX-Bus only.
733, 734 Wiegand Interface Module Provides system codeless entry, and arming and disarming using access control readers.
CellCom Series Digital Cellular
Communicator
Provides a fully supervised alarm communication path over the GSM/GPRS network.
DMP Two-Way Wireless Devices
1100X/*1100XH/*1100XI Wireless
Receiver
Supports up to 500 devices in residential or commercial wireless operation.
1101 Universal Transmitter
Provides both internal and external contacts that may be used at the same time to yield
two individual reporting zones from one wireless transmitter.
1102 Universal Transmitter
Provides an external contact.
* 1114 Four-Zone Expander
Provides four wireless zones
* 1116 Relay Output
Provides one Form C relay
* 1117 LED Annunciator
Provides a visual system status indicator
* 1118 Remote Indicator Light
Provides a visual indication of a Panic situation
* 1121 PIR Motion Detector
Provides motion detection with pet immunity.
1125 PIR Motion Detector
Provides multiple lens configurations, dual coverage area selection, and sensitivity
adjustments.
* 1129 Glassbreak Detector
Detects the shattering of framed glass mounted in an outside wall and provides full-pattern
coverage and false-alarm immunity.
XR500 Series Installation Guide
Digital Monitoring Products
5
Introduction
3.4
Accessory Devices (continued)
DMP Two-Way Wireless Devices (continued)
* 1131 Recessed Contact
Provides a recessed contact option for door or window applications.
* 1139 Bill Trap
Provides a silent alarm option for retail and banking cash drawers.
1142BC Two-button Hold-up Belt
Clip Transmitter
Provides two-button hold-up operation with a belt clip.
1142 Two-button Hold-up
Transmitter
Provides permanently mounted under-the-counter two-button hold-up operation.
* 1145 (Four-Button)
* 1146 (Two-Button)
* 1147 (One‑Button)
Key Fob transmitters designed to clip onto a key ring or lanyard.
1161 Residential Smoke Detector Residential smoke detector with sounder.
1162 Residential Smoke/Heat
Detector
Residential smoke/heat detector with sounder and fixed rate-of-rise heat detector.
1165 Commercial Smoke
Detector
Commercial smoke detector.
1165H Commercial Smoke/Heat
Detector
Commercial smoke/heat detector with fixed rate-of-rise heat detector.
1165HS Commercial Smoke/Heat Commercial smoke/heat detector with fixed rate-of-rise heat detector and sounder.
Detector and Sounder
1181 PIV
Commercial Post Indicator Valve (PIV)
1182 OS&Y
Commercial Outside Screw and Yoke Valve (OS&Y)
* This device has not been investigated and shall not be used in listed installations.
Indicating and Initiating Devices
865 Supervised Style W or X
Notification Circuit Module
Provides supervised alarm current when using the XR500 Series panel bell output and up to
5 Amps at 12 or 24 VDC when using a listed auxiliary power supply. The 865 can supervise
2-wire or 4-wire style circuits for opens and shorts with individual LED annunciation.
866 Style W Notification Circuit
Module
Provides supervised alarm current using the XR500 Series panel bell output and up to 5 Amps
at 12 or 24 VDC when using a listed auxiliary power supply. The 866 can supervise 2-wire
Style W circuits for opens and shorts.
867 Style W LX-Bus Notification
Circuit Module
Provides supervised alarm current using the XR500 Series panel bell output and up to 5 Amps
at 12 or 24 VDC when using a listed auxiliary power supply. The 867 connects to the XR500
Series panel LX-Bus™ and provides one 2-wire Style W notification circuit for open and short
conditions. Individual Bell Relay addresses Bell Ring styles.
869 Dual Class A Style D
Initiating Module
Provides two Class A, Style D, 4-wire initiating zones for connecting waterflow switches and
other non‑powered fire and burglary devices.
Accessory Modules and Keypads
893A Dual Phone Line Module
Allows you to supervise two standard phone lines connected to an XR500 Series panel. The
893A module monitors the main and backup phone lines for a sustained voltage drop and
alerts users when the phone line is bad.
* ePAD™ Virtual Keypads
Allows users to control the security system from any computer using the Internet.
iCOM™ Network Alarm Router
Allows the XR500 panel to send signals through the Internet/Ethernet.
iCOM-E™ High-Security Network
Alarm Router
Allow the XR500 panel to send encrypted signals through the Internet/Ethernet. For use
when the Advanced Encryption Standard (AES) Encryption Algorithm is required. The iCOM‑E
is NIST certified.
LCD keypads
Allows you to control the panel from various remote locations. Connect up to sixteen
supervised Model 630F Remote Fire Command Center, Model 690, 790, 693/793 Security
Command™ keypads, 7060, 7063, 7070, 7073, 7160, 7163, 7170, 7173 Thinline™ keypads,
7060A, 7063A, 7070A, 7073A Aqualite™ keypads, or 7760 Clear Touch™ keypad to the keypad
bus using terminals 7, 8, 9, and 10.
Addressable Smoke Detectors
521LX, 521LXT
Single-zone, addressable conventional smoke, smoke/heat detectors that connect to the
LX-Bus. Includes remote maintenance reporting, drift compensation, and multi-criteria
detection.
* This device has not been investigated and shall not be used in listed installations.
Digital Monitoring Products
6
XR500 Series Installation Guide
Installation
Installation
4.1
Mounting the Enclosure
The metal enclosure for the XR500 Series must be mounted in a secure, dry place to protect the panel from damage
due to tampering or the elements. It is not necessary to remove the XR500 Series PCB when installing the enclosure.
Figure 2 shows the mounting hole locations for the Model 350/350A Enclosures. Figure 3 shows the Model 341 Small
Enclosure. Figure 4 shows the Model 352X panel cabinet and 352S shelf cabinet for multiple batteries.
Note: When using the XR500 Series panel for listed applications, use the Model 350, 349, 341, or 352S enclosure for
standby batteries. When using the 352X or 352S in listed applications, the enclosure must be surface mounted on
the wall.
Enclosure Mounting Holes
J3
Phone Line
XR500 Series
Command Processor™
Panel
J21
Power
R
LED
L
J23
RS-232
J22
LX-Bus
X
Output 1
J10
Battery
Start
OVC
J2
K6
J8
PROG
3
4
5
6
7
8
9
10
11
12 13
14
J11
K7
AC AC +B –B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
2
3-Hole
Pattern for
Accessory
Modules
Output 2
Out1 Out2
J1
Ethernet
1
J6
Interface
Card
Expansion
Connector
J4
Tamper
Link LED
Activity LED
3
4
5
6
J16
Reset
Outputs 3-6
Z3 GND Z4 Z5 GND Z6
15 16
17
18 19
20
Z7 GND Z8 Z9+ Z9– Z10+ Z10–
21 22
23
24 25
26
27
28
Dual 1/2" and 3/4" Conduit Knockouts
Front and
Rear Tamper
Switches for
350A Attack
Resistant
Enclosure
Battery Shelf holds up to three 7 Ah Batteries
Figure 2: XR500 Series in Model 350 or 350A Enclosure
Lid Mounting Holes (4 places)
Lid Mounting Holes
(4 places)
J3
Phone Line
XR500 Series
Command Processor™
J4
Panel
Tamper
Link LED
Activity LED
J1
Ethernet
J21
RS-232
J22
LX-Bus
L
X
Output 1 OVC Output 2
J10
Battery
Start
J2
K6
J8
PROG
Out1 Out2
Power J23
R
LED
K7
AC AC +B –B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
1
2
3
4
5
6
7
8
9
10
11
12 13
14
3
4
5
6
J11
J16
Reset
Outputs 3-6
Z3 GND Z4 Z5 GND Z6
15 16
17
18 19
20
Z7 GND Z8 Z9+ Z9– Z10+ Z10–
21 22
23
24 25
26
27
28
Enclosure Mounting Holes (4 places)
Dual 1/2" and 3/4" Conduit Knockouts
Figure 3: XR500 Series in Model 341 Enclosure
XR500 Series Installation Guide
Digital Monitoring Products
7
Installation
56 VA
Transformer
Mounting
Plate
J3
Phone
Line
J4
Tamper
J1
Ethernet
Link LED
Activity LED
Power
LED
R
L
X
J23
RS232
5
4
3
2
XR500 Series
1
G
9
8
7
6
J22
LX-Bus
RED
J10
Output 1 OVC
AC +B
1
2
3
Out2
–B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
4
5
6
7
8
9
10
11 12
13 14
K7
Outputs 3-6
AC
J6 Expansion Slot
Output 2
Out1
RED
K6
J8
Z3 GND Z4
Z5 GND Z6
15 16
17
18 19
J16
Reset
20 21
Z7 GND Z8 Z9+ Z9– Z10+Z10–
22
23
24 25
26 27
28
Mounting for one (1)
Zone Expansion Module.
Battery Shelf
Figure 4: XR500 Series in Model 352X Enclosure and Separate 352S Enclosure with Shelves
4.2
Mounting Keypads and Zone Expansion Modules
DMP LCD keypads have removable covers that allow you to easily mount the keypad to a wall or other flat surface
using the screw holes on each corner of the base. Before mounting the base, connect the keypad wire harness leads
to the keypad cable from the panel and to any device wiring run to that location. Then attach the harness to the
pin connector on the PC board, mount the base, and install the keypad cover making sure all of the keys extend
through their respective holes.
For mounting keypads on solid walls, or for applications where conduit is required, use the Model 695 1-1/2” deep or
the Model 696 1/2” deep backboxes.
The DMP 711, 712-8, 714, 715, 716, and 717 modules are each contained in molded plastic housings with removable
covers. The base provides you with mounting holes for installing the unit to a wall, switch plate, or other surface.
Digital Monitoring Products
8
XR500 Series Installation Guide
Installation
4.3
Connecting LX-Bus and Keypad Bus Devices
Several factors determine the DMP LX-Bus™ and keypad bus performance characteristics: the wire length and gauge
used, the number of devices connected, and the voltage at each device. When planning an LX-Bus™ and keypad bus
installation, keep in mind the following information:
1. DMP recommends using 18 or 22-gauge unshielded wire for all keypad and LX-Bus circuits. Do not use
twisted pair or shielded wire for LX-Bus and keypad bus data circuits.
2.On keypad bus circuits, to maintain auxiliary power integrity when using 22-gauge wire do not exceed 500
feet. When using 18-gauge wire do not exceed 1,000 feet. To increase the wire length or to add devices,
install an additional power supply that is listed for Fire Protective Signaling, power limited, and regulated
(12 VDC nominal) with battery backup.
Note: Each panel allows a specific number of supervised keypads. Add additional keypads in the
unsupervised mode. Refer to the panel installation guide for the specific number of supervised keypads
allowed.
3.Maximum distance for any one bus circuit (length of wire) is 2,500 feet regardless of the wire gauge. This
distance can be in the form of one long wire run or multiple branches with all wiring totaling no more than
2,500 feet. As wire distance from the panel increases, DC voltage on the wire decreases. Maximum number
of LX-Bus devices on the first 2,500 foot circuit is 40 devices. 4. Maximum voltage drop between the panel (or auxiliary power supply) and any device is 2.0 VDC. If the
voltage at any device is less than the required level, add an auxiliary power supply at the end of the circuit.
When voltage is too low, the devices cannot operate properly.
For additional information refer to the LX-Bus/Keypad Bus Wiring Application Note (LT-2031).
Expansion Interface Cards (Models 481, 462N, 462P, 463G, and 472)
The LX-Bus provided on these cards requires only a 4-wire cable between the card and any devices connected to the
bus. You can connect devices (zone or output expansion modules) together on the same cable or provide separate
runs back to the card. Each LX-Bus provides up to 100 zones or outputs.
Note: Do not use twisted pair or shielded wire when connecting an LX-Bus or keypad bus.
Primary Power Supply
5.1
AC Terminals 1 and 2
Connect the transformer wires to terminals 1 and 2 on the panel. Use no more than 70 ft. of 16 gauge or 40 ft. of 18
gauge wire between the transformer and the XR500 Series.
5.2
Always ground the panel before applying power to any devices: The XR500 Series must be properly
grounded before connecting any devices or applying power to the panel. Proper grounding protects
against Electrostatic Discharge (ESD) that can damage system components. See the Earth ground section.
Transformer Types
Use Model 327 (16.5 VAC 50 VA) plug-in or Model 322 or 323 (16 VAC 56 VA) wire-in transformer. Use Model 322 or
323 (16 VAC 56 VA) wire-in transformer when required by the Authority Having Jurisdiction (AHJ).
The transformer must be connected to an unswitched 120 VAC 60 Hz electrical outlet with at least .87A of
available current. Never share the transformer output with any other equipment.
XR500 Series Installation Guide
Digital Monitoring Products
9
Installation
Secondary Power Supply
6.1
Battery Terminals 3 and 4
Connect the black battery lead to the negative
battery terminal. The negative terminal connects to
the enclosure ground internally through the XR500
Series circuit board. Connect the red battery lead to
the battery positive terminal. Observe polarity when
connecting the battery.
You can add a second battery in parallel using the
DMP Model 318 Dual Battery Harness. DMP requires
each battery be separated by a PTC in the battery
harness wiring to protect each battery from a
reversal or short within the circuit. See Figure 5.
Battery
Start
AC AC +B –B BELL GND
Battery
318 Battery
Harness
To AC
Red
PTC
318 Battery
Harness
Command
Processor
Panel
Red
Black
PTC
2
3
4
5
6
Panel Red and
Black Battery Cables
14 AWG to
Earth Ground
To Bell
Circuit
Black
Battery
1
Battery
For listed installations, all batteries shall be
installed in a DMP Model 350 or Model 352S
Figure 5: Wiring Multiple Batteries
enclosure and all wiring shall run through conduit.
The enclosure shall be installed to the left of the XR500 Series enclosure to ensure Battery and AC wire
separation.
Use sealed lead-acid batteries only: Use the DMP Model 365 (12 VDC 9 Ah), DMP Model 367 (12 VDC
7.7 Ah), Model 366 (12 VDC 18 Ah), Model 368 (12 VDC 4.5 Ah), or Model 369 (12 VDC 7 Ah) sealed
lead‑acid rechargeable battery. Batteries supplied by DMP have been tested to ensure proper charging
with DMP products.
GEL CELL BATTERIES CANNOT BE USED WITH THE XR500 SERIES PANEL.
6.2
Earth Ground (GND)
To provide proper transient suppression, XR500 Series panel terminal 4 must be connected to earth ground using
14 gauge or larger wire. DMP recommends connecting to a cold water pipe, ground rod, or building ground only. Do
not connect to an electrical ground or conduit, sprinkler or gas pipes, or to a telephone company ground.
6.3
Battery Only Restart
When powering up the XR500 Series panel without AC power, briefly short across the battery start pads to pull in
the battery cutoff relay. The leads need a momentary short only. Once the relay has pulled in, the battery voltage
holds it in that condition. If the XR500 Series panel is powered up with an AC transformer, the battery cutoff relay is
pulled in automatically. For more information refer to Figure 1.
6.4
Battery Replacement Period
DMP recommends replacing the battery every 3 to 5 years under normal use.
6.5
Discharge/Recharge
The XR500 Series battery charging circuit float charges at 13.9 VDC at a maximum current of 1.0 Amps using a
50 VA or 56 VA transformer. Listed below are the various battery voltage level conditions:
Battery Trouble:
Below 11.9 VDC
Battery Cutoff:
Below 10.2 VDC
Battery Restored:
Above 12.6 VDC
6.6
Battery Supervision
The XR500 Series tests the battery when AC power is present. The test is done every three minutes and lasts for five
seconds. During the test, the panel places a load on the battery; if the battery voltage falls below 11.9 VDC a low
battery is detected. If AC power is not present, a low battery is detected any time the battery voltage falls below
11.9 VDC.
If a low battery is detected with AC power present, the test repeats every two minutes until the battery charges
above 12.6 VDC indicating the battery has restored voltage. If a weak battery is replaced with a fully charged
battery, the restored battery will not be detected until the next two minute test is completed.
6.7
Battery Cutoff
The panel disconnects the battery any time the battery voltage drops below 10.2 VDC. This prevents battery deep
discharge damage.
Digital Monitoring Products
10
XR500 Series Installation Guide
Installation
6.8
XR500 Series Power Requirements
During AC power failure, the XR500 Series panel and all connected auxiliary devices draw their power from the
battery. All devices must be taken into consideration when calculating the battery standby capacity. The following
table lists the XR500 Series panel power requirements. You must add the additional current draw of keypads, zone
expansion modules, smoke detector output, and any other auxiliary devices used in the system for the total current
required. The total is then multiplied by the number of standby hours required to calculate the total ampere-hours
required.
Standby Battery Power Calculations
Standby Current
XR500 Series Control Panel
Relay Outputs 1-2 (ON)
Switch Grounds 3-6 (ON)
Active Zones 1-8
Active Zones 9-10
2-Wire Smoke Detectors
Panel Bell Output
Qty
Qty
Qty
Qty
Qty
Qty
1 _ x 180mA 180 mA
_______
30mA ______
_______
5mA ______
_______
1.6mA ______
_______
4mA ______
_______
0.1mA ______
893A Dual Phone Line Module
Qty _______
x
461 Interface Adaptor Card
12mA ______
Alarm Current
Qty
Qty
Qty
Qty
Qty
Qty
1 _ x
_______
_______
_______
_______
_______
Qty _______
x
7mA ______
180mA
30mA
5mA
*2mA
30mA
0.1mA
1500mA
180 mA
______
______
______
______
______
______mA
50mA ______
7mA ______
462N Network Interface Card
Qty _______
x
50mA ______
Qty _______
x
50mA ______
462P Printer Interface Card
Qty _______
x
50mA ______
Qty _______
x
50mA ______
463G/CellCom Digital Cellular Communicator Card Qty _______
x
21mA ______
Qty _______
x
21mA ______
472 FA Wireless Interface Card
Qty _______
x
85mA ______
Qty _______
x
85mA ______
481 Expansion Interface Card
Qty _______
x
15mA ______
Qty _______
x
15mA ______
1100X Wireless Receiver
Qty _______
x
46mA ______
Qty _______
x
46mA ______
1100XH Wireless High Power Receiver
Qty _______
x 160mA ______
Qty _______
x
160mA ______
1100XI Wireless In-line Receiver
Qty _______
45mA ______
Qty _______
x
45mA ______
860 Relay Output Module (one relay active)
All four relays active
Qty _______
x
34mA ______
138mA ______
Qty _______
x
34mA ______
138mA ______
865 Style Y or Z Notification Module
Qty _______
x
26mA ______
Qty _______
x
85mA ______
866 Style W Notification Module
Qty _______
x
45mA ______
Qty _______
x
76mA ______
867 LX-Bus Style W Notification Module
Qty _______
x
30mA ______
Qty _______
x
86mA ______
869 Dual Style D Initiating Module
Qty _______
x
25mA ______
Qty _______
x
75mA ______
630F Remote Fire Command Center
Qty _______
x
63mA ______
Qty _______
x
92mA ______
690 Security Command Keypad
Qty _______
x
77mA ______
Qty _______
x
84mA ______
693/793 Easy Entry Keypad
Active Zones (EOL Installed)
Qty _______
x
92mA ______
1.6mA ______
Qty _______
Qty _______
x
x
120mA ______
*2mA ______
790 Security Command Keypad
Active Zones (EOL Installed)
Qty _______
x
77mA ______
1.6mA ______
Qty _______
Qty _______
x
x
84mA ______
*2mA ______
7060/7160 Thinline/7060A Aqualite Keypad
Qty _______
x
72mA ______
Qty _______
x
80mA ______
7063/7163 Thinline/7063A Aqualite Keypad
Qty _______
x
85mA ______
Qty _______
x
100mA ______
7070/7170 Thinline/7070A Aqualite Keypad
Active Zones (EOL Installed)
Qty _______
x
72mA ______
1.6mA ______
Qty _______
Qty _______
x
x
87mA ______
*2mA ______
7073/7173 Thinline/7073A Aqualite Keypad
Active Zones (EOL Installed)
Qty _______
x
85mA ______
1.6mA ______
Qty _______
Qty _______
x
x
100mA ______
*2mA ______
7760 Clear Touch Keypad
Qty _______
x
65mA ______
Qty _______
x
115mA ______
733 Wiegand Interface Module
Active Zones (EOL Installed)
Annunciator (ON)
Qty _______
Qty _______
x
x
30mA ______
1.6mA ______
Qty _______
Qty _______
Qty _______
x
x
x
30mA ______
*2mA ______
20mA ______
734 Wiegand Interface Module
Active Zones (EOL Installed)
Annunciator (ON)
Qty _______
Qty _______
x
x
15mA ______
1.6mA ______
Qty _______
Qty _______
Qty _______
x
x
x
15mA ______
*2mA ______
20mA ______
Copy Sub-Totals to next page
*Based on 10% of active zones in alarm.
XR500 Series Installation Guide
Sub-Total Standby ______mA
Sub-Total Alarm ______mA
Digital Monitoring Products
11
Installation
Standby Battery Power Calculations
Standby Current
Alarm Current
736P POPIT Interface Module
Radionics Popex, POPITs, OctoPOPITs
Qty _______
Qty _______
x 25mA ______
x ___mA ______
Qty _______
Qty _______
x
x
25mA ______
___mA ______
738A Ademco Wireless Interface Module
Qty _______
x
75mA ______
Qty _______
x
75mA ______
710 Bus Splitter/Repeater Module
Qty _______
x
32mA ______
Qty _______
x
32mA ______
710F Fire Bus Splitter/Repeater Module
Qty _______
x
40mA ______
Qty _______
x
40mA ______
711 Zone Expansion Module
Active Zone (EOL Installed)
Qty _______
Qty _______
x
x
11mA ______
1.6mA ______
Qty _______
Qty _______
x
x
11mA ______
*2mA ______
714 Zone Expansion Module
Active Zones (EOL Installed)
Qty _______
Qty _______
x
x
7mA ______
1.6mA ______
Qty _______
Qty _______
x
x
7mA ______
*2mA ______
712-8 Zone Expansion Module
Active Zones (EOL Installed)
Qty _______
Qty _______
x
x
17mA ______
1.6mA ______
Qty _______
Qty _______
x
x
17mA ______
*2mA ______
714-8, 714-16 Zone Expansion Module
Active Zones (EOL Installed)
Qty _______
Qty _______
x
x
20mA ______
1.6mA ______
Qty _______
Qty _______
x
x
20mA ______
*2mA ______
715 Zone Expansion Module
Active Zones (EOL Installed)
2-Wire Smokes
Qty _______
Qty _______
Qty _______
x
x
x
7mA ______
4mA ______
.1mA ______
Qty _______
Qty _______
Qty _______
x
x
x
7mA ______
*30mA ______
.1mA ______
715-8, 715-16 Zone Expansion Modules
Active Zones (EOL Installed)
2-Wire Smokes
Qty _______
Qty _______
Qty _______
x
x
x
20mA ______
4mA ______
.1mA ______
Qty _______
Qty _______
Qty _______
x
x
x
20mA ______
*30mA ______
.1mA ______
716 Output Expansion Module
Active Form C Relays
Qty _______
x
13mA ______
Qty _______
Qty _______
x
x
13mA ______
12mA ______
717 Graphic Annunciator Module
Annunciator Outputs
Qty _______
x
10mA ______
Qty _______
Qty _______
x
x
10mA ______
1mA ______
521LX, 521LXT Smoke Detectors
Qty _______
x
8.8mA ______
Qty _______
x
*28mA ______
572 Indicator LED
Qty _______
x
20mA ______
Qty _______
x
20mA ______
iCOM, iCOM-E Network Alarm Routers
Qty _______
x 78.1mA ______
Qty _______
x 78.1mA ______
Aux. Powered Devices on Terminals 7 and 11
Other than Keypads and LX-Bus Modules
______mA
______mA
This page only
Sub-Total Standby ______mA
Sub-Total Alarm ______mA
Sub-Totals from previous page
*Based on 10% of active zones in alarm
Sub-Total Standby ______mA
Total Standby ______mA
Sub-Total Alarm ______mA
Total Alarm ______mA
Total Standby______mA x number of Standby Hours needed ______ =
_______mA-hours
Total Alarm ______mA +_______mA-hours
Total _______mA-hours
X
.001
= _______Amp-hrs
Required
Refer to section 6.9 for standby battery selection.
Digital Monitoring Products
12
XR500 Series Installation Guide
Installation
6.9
Standby Battery Selection
To choose the type and number of batteries needed for 24, 60, or 72 hours of standby power based on the Amp Hours
Required calculation from section 6.8 XR500 Series Power Requirements, perform the following:
1.Select the desired standby hours required from the table below: 24, 60, or 72 hours
2.Select the desired battery size: Model 368 (12 VDC 4.5 Ah), Model 369 (12 VDC 7 Ah),
Model 367 (12 VDC 7.7 Ah), Model 365 (12 VDC 9 Ah), Model 366 (12 VDC 18 Ah).
3.Select a Max. Ah Available number that is just greater than the number calculated in Amp Hours Required.
4.Install the number of batteries shown in the corresponding No. of Batteries required column.
Example: If the Amp Hours Required calculation equals 22 Ah for 24 hours of standby time and 4.5 Ah batteries
are desired, install six (6) Model 368 (12 VDC, 4.5 Ah) batteries.
Note: You can use either a Model 327 Plug-in 50 VA or Model 322 or 323 Wire-in 56 VA Transformer with any of the
Number of Batteries choices listed below.
For listed installations, all batteries shall be installed in a DMP Model 341, 349, 350 or 352S enclosure and all wiring
shall run through conduit. The enclosure shall be installed to the left of the XR500 Series enclosure to ensure
Battery and AC wire separation.
24 hours of standby power
4.5 Ah Batteries
7 Ah Batteries
7.7 Ah Batteries
9 Ah Batteries
18 Ah Batteries
Max. Ah No. of
Max. Ah No. of
Max. Ah No. of
Max. Ah No. of
Max. Ah No. of
Available Batteries
Available Batteries
Available Batteries
Available Batteries
Available Batteries
8
2
6
1
6
1
8
1
16
1
12
3
12
2
13
2
16
2
32
2
16
4
18
3
20
3
24
3
48
3
20
5
24
4
27
4
32
4
24
6
31
5
34
5
40
5
28
7
37
6
41
6
32
8
43
7
36
9
Note: 48 hours is the typical battery recharge time for any of the Number of Batteries
shown in this section.
40
10
60 hours of standby power
7 Ah Batteries
7.7 Ah Batteries
Max. Ah No. of
Max. Ah No. of
Available Batteries
Available Batteries
13
2
14
2
20
3
22
3
27
4
29
4
33
5
37
5
40
6
44
6
47
7
52
7
54
8
59
8
60
9
67
9
67
10
9 Ah Batteries
Max. Ah No. of
Available Batteries
17
2
26
3
34
4
43
5
52
6
61
7
69
8
18 Ah Batteries
Max. Ah No. of
Available Batteries
17
1
34
2
52
3
69
4
Note: 48 hours is the typical battery
recharge time for any of the Number of
Batteries shown in this section.
72 hours of standby power
9 Ah Batteries
18 Ah Batteries
Max. Ah No. of
Max. Ah No. of
Available Batteries
Available Batteries
16
2
16
1
25
3
33
2
33
4
50
3
42
5
67
4
50
6
59
7
Note: 72 hours is the typical battery recharge time required for any of the Number of
Batteries shown in this section.
67
8
Note: If the Amp Hours Required calculation is greater than any Max. Ah Available number shown on a table, then
add power supply(s) to power some system devices allowing the Amp Hours Required calculation to be reduced. See
the 710/710F Bus Splitter/Repeater Installation Guide (LT-0310).
XR500 Series Installation Guide
Digital Monitoring Products
13
Installation
Bell Output
7.1
Terminals 5 and 6
Terminal 5 supplies positive 12 VDC to power alarm bells or horns. This output can be steady, pulsed, or temporal
depending upon the Bell Action specified in Bell Options. Terminal 6 is the ground reference for the bell circuit. This
supervised output detects 1k Ohms or less as normal. The indicating appliance can supply this resistance. If using a
horn or siren, a 1k Ohm 1/2 W EOL resistor (provided) should be added across the bell circuit to provide supervision.
See the Notification Appliance section for a list of approved notification appliances and the Wiring Diagrams for
connections.
Keypad Bus
8.1
Description
XR500 Series panel terminals 7, 8, 9, and 10 are for the keypad bus. You can connect up to sixteen supervised
keypads and multiple unsupervised keypads to the XR500 Series. In addition to DMP LCD keypads, you can also
connect any combination of zone expansion modules to the data bus. Refer to the specific device installation sheet
for the maximum number of Keypad Bus devices.
Refer to the section titled LX-Bus for complete information about the LX-Bus 4-pin header and expansion slot.
Note: Do not use shielded wire for LX-Bus/Keypad Bus circuits.
8.2
Terminal 7 - RED
This terminal supplies positive 12 VDC Regulated to power DMP LCD keypads and zone expansion modules. Terminal 7
also supplies power for any auxiliary device. The ground reference for terminal 7 is terminal 10.
The output current is shared with the smoke power output on terminal 11 and Zones 9 and 10. Current draw for all
connected devices must not exceed the panel maximum current rating. See Power Supply in the Compliance section
for maximum current in a fire listed application.
8.3
Terminal 8 - YELLOW
Terminal 8 receives data from keypads and zone expansion modules. It cannot be used for any other purpose.
8.4
Terminal 9 - GREEN
Terminal 9 transmits data to keypads and zone expansion modules. It cannot be used for any other purpose.
8.5
Terminal 10 - BLACK
Terminal 10 is the ground reference for DMP LCD keypads, zone expansion modules, and all auxiliary devices being
powered by terminal 7.
8.6
J8 Programming Connection
A 4-pin header (J8) is provided to connect a keypad when using a DMP Model 330 Programming Cable. This provides
a quick and easy connection for panel programming.
You may also use the J8 Programming Header to connect Keypad Bus devices. This is an alternative to connecting
keypad bus devices to terminals 7, 8, 9, and 10.
8.7
OVC LED
The Overcurrent LED (OVC) lights Red when the devices connected to the Keypad Bus and LX-Bus(es) draw more
current than the panel is rated for. The OVC is located above Outputs 1 and 2 on the panel and turns a steady Red
when lit. When the OVC LED lights Red, the LX-Bus(es) and Keypad bus are shut down.
Smoke and Glassbreak Detector Output
9.1
Terminals 11 and 12
Terminal 11 supplies positive 12 VDC Regulated to power 4-wire smoke detectors and other powered devices. This
output can be turned off by the user for 5 seconds using the Sensor Reset User Menu option to allow latched devices
to reset. Terminal 12 is the ground reference for terminal 11.
9.2
Current Rating
The Output current from terminal 11 is shared with terminals 7, 25, and 27.
The total current draw of all devices powered from the panel must be included with terminal 11
calculations and must not exceed the maximum output rating.
Digital Monitoring Products
14
XR500 Series Installation Guide
Installation
Protection Zones
10.1 Terminals 13–24
Zones 1 to 8 (terminals 13 to 24) on the XR500 Series panel are all grounded burglary zones. For programming
purposes, the zone numbers are 1 through 8. Listed below are terminal 13 to 24 connection functions.
Terminal
13
14
15
16
17
18
Function
Zone 1 voltage sensing
Ground for Zones 1 and 2
Zone 2 voltage sensing
Zone 3 voltage sensing
Ground for Zones 3 and 4
Zone 4 voltage sensing
Terminal
19
20
21
22
23
24
Function
Zone 5 voltage sensing
Ground for Zones 5 and 6
Zone 6 voltage sensing
Zone 7 voltage sensing
Ground for Zones 7 and 8
Zone 8 voltage sensing
The voltage sensing terminal measures the voltage across a 1k Ohm End-of-Line resistor to ground. Use DMP Model
311 1k Ohm resistors. Dry contact sensing devices can be used in series (normally-closed) or in parallel (normallyopen) with any of the burglary protection zones.
1K Ohm
Normally
Closed
1K Ohm
Normally Open
1K Ohm
Combination Normally Open
and Normally Closed
Figure 6: Protection Zone Wiring
10.2 Operational Parameters
Each protection zone detects three conditions: Open, Normal, and Short. Listed below are voltage and resistance
parameters for each condition:
Condition Open
Normal
Short
Resistance on zone
over 1300 ohms
600 to 1300 ohms
under 600 ohms
Voltage on positive terminal
over 2.0 VDC
1.2 to 2.0 VDC
under 1.2 VDC
10.3 Zone Response Time
A condition must be present on a zone for 500 milliseconds before it is detected by the XR500 Series panel.
Ensure detection devices used on the protec­tion zones are rated for use with this delay. Zones 1-10 can also be
programmed for a fast response delay of 160 milliseconds.
10.4 Keyswitch Arming Zone
Using a keyswitch on an Arming type zone allows you to arm and disarm selected areas without having to enter a
user code.
Powered Zones for 2-Wire Smoke Detectors
11.1 Terminals 25–26 and 27–28
Panel terminals 25 through 28 provide two resettable Class B, Style A, 2-wire powered zones. For programming
purposes the zone numbers are 9 and 10.
Note: The maximum wire length for either zone 9 or zone 10 is 3000 feet using 18 AWG or 1000 feet using 22
AWG. The maximum voltage is 14 VDC and the maximum normal standby current is 1.25mA DC. The maximum line
impedance is 100 Ohms. The maximum short circuit current is 56mA.
When using 725 Zone Expansion Modules, use listed Model 316 EOL resistors. The compatibility identifier for the
zones using 725 Zone Expansion Modules is B. When using all other zone expansion modules, use listed Model 309
EOL resistors. The compatibility identifier for the zones is A. Note: Do not mix detectors from different manufacturers on the same zone.
Caution: Performing a Sensor Reset momentarily drops power to the devices on Zones 9 and 10. The
panel views these zones (9 and 10) as “Open” while the power is absent.
XR500 Series Installation Guide
Digital Monitoring Products
15
Installation
11.2 Compatible 2-Wire Smoke Detector Chart
Manufacturer
Model
Detector
ID
Base
Detection Systems
DS230, DS230F
B/A
MB2W, MB2WL
A
8.5-33
10
Detection Systems
DS250, DS250TH
B
MB2W, MB2WL
A
8.5-33
10/12
Detection Systems
DS250HD
B
MB2W, MB2WL
A
8.5-33
10
B/A
MB2W, MB2WL
A
8.5-33
17
8.5-33
10/12
715, 715-8,
715-16, 725
8-35
14
725
Detection Systems
DS260
DS282, DS282TH,
Detection Systems
DS282THC,
DS282THS
SLR-835B-2
Hochiki
SLR-835BH-2
Hochiki
SLR-24, SLR-24H
SIJ-24, DCD-190,
Hochiki
DCD-135
Hochiki
SLR-24, SLR-24H
Hochiki
SIJ-24
Hochiki
DCD-190, DCD-135
429AT, 521B,
Sentrol/ESL
521BXT, 521NB,
521NBXT
429C, 429CT,
Sentrol/ESL
521B/BXT
429CRT, 429CST,
Sentrol/ESL
429CSST, 521CRXT
711U, 712U, 713Sentrol/ESL
5U, 713-6U, 721U,
721UT
Base
DC
# of
Zone
Panel
ID
Voltage Detectors Expansion Zones
Range (12V/24V) Modules
B
HD-6
N/A
HD-3
NS4-220
HB-3
15-33
15
725
HD-3
NS4-220
HB-3
15-33
15
725
HD-3
HD-3
HD-3
NS6-220
NS6-220
NS6-220
HB-3
HB-3
HB-3
15-33
15-33
15-33
15
20
16
725
725
725
S09A
6.5-20
12
715, 715-8,
715-16
S10A
8.5-33
12
725
S11A
8.5-33
12
725
S10A
701E, 70-1U,
702E, 702U
S00
8.5-33
12
725
701E, 701U,
702E, 702U,
702RE, 702RU
S00
8.5-33
12
725
8.5-35
10
Sentrol/ESL
731U, 723U
S11A
System Sensor
1400
A
System Sensor
1151, 2151
A
B110PL, B401
8.5-35
10/10
System Sensor
1451, 2451TH
A
B401, B401B
8.5-35
10
System Sensor
1451DH
A
DH400
8.5-35
10
A
8.5-35
10
A
8.5-35
10
8.5-35
10
System Sensor
System Sensor
2100T, 2100B,
2100TB, 2100D,
2100TD
2400, 2400AT,
2400AIT, 2400TH
725
715, 715-8,
715-16, 725
715, 715-8,
715-16
725
B401, B401B,
DH400
System Sensor
2451
A
System Sensor
2W-B, 2WT-B
A
8.5-35
10
System Sensor
DH100P, DH100LP
A
8.5-35
10
715, 715-8,
715-16
715, 715-8,
715-16, 725
715, 715-8,
715-16
715, 715-8,
715-16
715, 715-8,
715-16
715, 715-8,
715-16
715, 715-8,
715-16
715, 715-8,
715-16
715, 715-8,
715-16, 725
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
9 & 10
Figure 7: Compatible 2-Wire Smoke Detectors
Digital Monitoring Products
16
XR500 Series Installation Guide
Installation
Dry Contact Relay Outputs
12.1 Description
The XR500 Series panel provides two programmable auxiliary SPDT relays when equipped with two DMP Model 305
relays in sockets K6 (Output 1) and K7 (Output 2) and a Model 431 Output Harness on the J2 6-pin Header. Each relay
provides one SPDT set of contacts that can be operated by any of the functions listed below:
1)Activation by zone condition: Steady, Pulsing, Momentary, and Follow
2)Activation by 24-hour 7-day schedule: One on and one off time a day for each relay
3)Manual activation from the DMP LCD keypad menu
4)Communication failure
8) Exit and Entry timers
5)Armed area annunciation
9) System Ready
6)Fire Alarm, Fire Trouble or Supervisory
10) Late to Close
7)Ambush Alarm
Refer to the XR500 Series Programming Guide (LT-0679) for specific information.
12.2 Contact Rating
The Model 305 relay contacts are rated for 1 Amp at 30 VDC (allows .35 power factor). You can connect auxiliary
power to the Relay Output 1 common terminal by installing the gray harness wire to terminal 7. Current draw for all
connected devices must not exceed the panel maximum current rating.
12.3 Model 431 Output Harness Wiring
The relay contacts are accessible by installing the DMP 431 Output Harness on the 6-pin header labeled J2. Output 2
uses the top three prongs, and Output 1 uses the bottom three prongs. The wire harness and contact locations are
shown below:
Contact
Color
Output 1 normally closed
Violet
Output 1 common
Gray
Output 1 normally open
Orange
Output 2 normally closed
Violet with white stripe
Output 2 common
White with gray stripe
Output 2 normally open
Orange with white stripe
The relay contacts must be connected to devices located within the same room as the XR500 Series panel.
Annunciator Outputs
13.1 Description
The four programmable annunciator outputs can be programmed to indicate the activity of the panel zones or
conditions occurring on the system. Annunciator outputs do not provide a voltage but instead switch-to-ground a
voltage from another source. The outputs can respond to any of the conditions listed in the Description section for
Dry Contact Relays. Maximum voltage is 30 VDC @ 50mA.
13.2 Model 300 Harness Wiring
Access the open collector outputs by installing DMP 300 Harness on the 4-pin header labeled J11. The output
locations are shown below. For listed applications, devices connected to the outputs must be located within the
same room as the panel.
Output
3
4
Color
Red
Yellow
Wire
1
2
Output
5
6
Color
Green
Black
Wire
3
4
13.3 Model 860 Relay Module
Connect a Model 860 Relay Module to the J11 on the XR500 Series panel to provide relays for outputs 3-6. Use these
relays for electrical isolation between the alarm panel and other systems or for switching voltage to control various
functions. Power is supplied to the relay coils from a single wire connected to the panel auxiliary power terminal 7.
The module includes one relay and provides three additional sockets for expansion of up to four relays. Mount the
860 inside the panel enclosure using the 3-hole pattern and plastic standoffs. Refer to the 860 Module Install Sheet
(LT-0484) as needed.
Relay Contact Rating: 1 Amp at 30 VDC (allows .35 power factor)
XR500 Series Installation Guide
Digital Monitoring Products
17
Installation
J23 6-Pin Header
14.1 Description
The XR500 Series Command Processor™ panel supports RS-232, LX-Bus, and DMP Wireless operation. Only one
operation can function at a time. Install a jumper on one pair of J23 headers to indicate how the panel is
programmed to operate. Refer to the table below when installing a jumper on J23. When a jumper is installed or
moved on the 6-pin header, briefly reset the panel using the J16 jumper to activate the selected operation.
Note: Only one operation, RS-232, LX-Bus, or DMP Wireless can function at a time.
Letter
R
L
X
J23 6-Pin Header
Operation
Standard RS-232
LX-Bus
1100 Series DMP Wireless
J21
R
L
X
J23
RS-232
J22
LX
LEDs
Xmit
Rec
Overcurrent
(OVC) LED
Figure 8: J23 6-Pin Header
J22 LX-Bus Expansion Connector
15.1 Description
The XR500 Series Command Processor™ Panel supports up to 500 wireless bus zones or up to five LX-Bus circuits. Each Interface card LX-Bus circuit provides 100 expansion zones. The maximum number of LX-Bus zones available
on a fully populated panel is 500. Use LX-Bus J22 Header for 100 zones. Install a single Interface Card Connector
on the board to support 100 additional zones for a total of 200 zones. To install up to five Interface Cards install a
Model 461 Interface Adaptor Card.
15.2 J22 LX-Bus Header
Note: Only one connector, J21 or J22 can function at a time. Either use J21 to connect a serial device for PC Log
Reporting, or use J22 to connect an LX-Bus or DMP Wireless device. Operation is determined by where you install
the jumper on the J23 6-Pin header. See the Connecting LX-Bus and Keypad Bus Devices section for maximum wiring
distances.
For each connection, respect wire colors when connecting devices and use all four wires. After placing the jumper
on the J23 6-Pin header to enable the required operation, briefly reset the panel using the J16 jumper to activate
operation.
Wireless Bus Operation: Place a jumper on the two pins next to the letter “X” on the J23 6-Pin header. When using
J22 as a wireless bus, connect a DMP Model 300 4-wire Harness to the J22 4-pin header labeled LX. Connect the
other end to the J3 header on the 1100X Wireless Receiver. This provides up to 500 wireless zones numbered 500 to
999. Refer to the 1100X Wireless Receiver Install Guide (LT-0708). LX-Bus Operation: Place a jumper on the two pins next to the letter “L” on the J23 6-Pin header. When using J22 as
an LX-Bus, connect a DMP Model 300 4-wire Harness to the J22 4-pin header labeled LX. This provides the first 100
LX-Bus zones numbered 500-599. No LX-Bus Interface Card is required.
Note: Do NOT use shielded wire when using the J22 LX-Bus Header.
RS-232 Operation: Place a jumper on the two pins next to the letter “R” on the J23 6-Pin header and refer to J21
Serial Connector.
Digital Monitoring Products
18
XR500 Series Installation Guide
Installation
15.3 LX-Bus Interface Cards
You can add one Interface Card (Model 481, 462N, 462P, 463G, or 472) to the XR500 Series using J6 Interface Card
Connector located on the board right edge. To add more than one Interface Card install a 461 Interface Adaptor
Card using J6 Interface Card Connector on the board right edge. The 461 Adaptor Card allows up to five Interface
Cards to be installed. Refer to the 461 Installation Sheet (LT-0736). Each Interface card provides up to 100 LX-Bus
Zones. Refer to the following tables to identify zone locations and numbers relative to J22 operation.
J22 LX-Bus Enabled
(Set J23 to “L”)
LX-Bus Zone Numbers
1
500-599
AND
J22
LX-Bus
NOT
Enabled
(J23
NOT set
to “L”)
461 Adaptor Card and
Multiple Interface Cards
LX-Bus Zone Numbers
LX-Bus Zone Numbers
2
600-699
2 (A)
600-699
OR
3 (B)
700-799
4 (C)
800-899
5 (D)
900-999
One Interface Card
461 Adaptor Card and
Multiple Interface Cards
LX-Bus Zone Numbers
LX-Bus Zone Numbers
1
500-599
1 (A)
500-599
OR
2 (B)
600-699
3 (C)
700-799
4 (D)
800-899
5 (E)
900-999
One Interface Card
15.4 LX-Bus LEDs
The two LEDs, located near the bottom-right corner of J21 indicate data transmission and receipt. The top LED
flashes green to indicate the panel is transmitting LX-Bus data. The bottom LED flashes yellow to indicate the panel
is receiving LX-Bus data.
15.5 OVC LED
The Overcurrent LED (OVC) lights Red when the devices connected to the Keypad Bus and LX-Bus(es) draw more
current than the panel is rated for. The OVC is located above Outputs 1 and 2 on the panel and turns a steady Red
when lit. When the OVC LED lights Red, the LX-Bus(es) and Keypad bus shut down.
J21 Serial Connector
16.1 Description
Note: Only one connector, J21 or J22 can function at a time. Either use J21 to connect a serial device for PC Log
Reporting, or use J22 to connect a DMP Wireless device or an LX-Bus device. Operation is determined by where you
install the jumper on the J23 6-Pin header. The maximum line impedance is 100 Ohms.
To enable J21 to operate in RS-232 mode, place a jumper on the two pins next to the letter “R” on the J23 6-Pin
header and briefly reset the panel using the J16 jumper to activate the selected operation. Panel programming
using Remote Link™ can be set up through a direct connection to a computer or through an iCOM connected to a
network. The Serial Connector allows the following operation options.
XR500 Panel
XR500N/XR500E Panel
PC Log Reports
PC Log Reports
Remote Link™
Programming
Additional iCOM Installed
for PC Log Reports
16.2 Computer Connection to J21
J21
R
L
X
J23
DB-9 Female Connector
RS-232
J22
Serial Data Xmit LED
Serial Data Rec(eive) LED
Figure 9: J21 Serial Connection
Use a straight through RS-232 Serial cable with a DB-9 female connector on one end and a DB-9 male connector on
the other end. Plug the DB-9 male connector end of the cable onto the XR500 Series panel J21 RS-232 connector.
Plug the DB-9 female connector end of the cable onto the DB‑9 male connector located at the back of the computer.
Program the XR500 Series panel as needed then disconnect the computer.
XR500 Series Installation Guide
Digital Monitoring Products
19
Installation
16.3 Direct iCOM Connection to J21
Use DMP Model 397 cable with a DB-9 female connector on one end and an RJ connector on the other end. Mount
the iCOM in the panel enclosure. Refer to the iCOM Installation Guide (LT-0587). Plug the 397 cable DB-9 male
connector end onto the XR500 Series panel J21 RS-232 connector. Plug the RJ connector into the iCOM J1 Network
connector. Program the XR500 Series panel as needed.
16.4 Serial Connector LEDs
The two LEDs, located near the bottom-right corner of J21 indicate data transmission and receipt. The top LED
flashes green to indicate the panel is transmitting serial data. The bottom LED flashes yellow to indicate the panel
is receiving serial data.
J1 Ethernet Connector (XR500N/XR500E only)
17.1 Description
The J1 Ethernet Connector is available on the XR500N/XR500E Network version to connect directly to an Ethernet
network using a standard patch cable. The maximum impedance is 100 Ohms.
17.2 Ethernet LEDs
The two LEDs, located to the left of J1 Ethernet Connector, indicate network
J1
Link LED
Ethernet
operation. The top, Link LED flashes green to indicate the network traffic is good. Activity LED
The bottom, Activity LED flashes yellow to indicate messages are being sent and
Figure 10: J1 Header and LEDs
received.
J3 Telephone RJ Connector
18.1 Description
Connect the panel to the public telephone network by installing a DMP 356 RJ Cable between the panel J3 connector
and the RJ31X or RJ38X phone block. The maximum impedance is 100 Ohms. CAUTION - To reduce the risk of fire,
use only No. 26 AWG or larger telecommunication line cord, such as DMP Model 356 Series Phone Cords.
18.2 J10 893A Connector
Connect an 893A Dual Phone Line Module to J10 on the XR500 Series. Refer to the 893A Installation Sheet (LT‑0135)
for complete information.
18.3 Notification
The user must not repair registered terminal equipment. In case of trouble, immediately unplug the device from the
telephone jack. The factory warranty provides for repairs. Registered terminal equipment may not be used on party
lines or in connection with coin telephones. No­tify the telephone company with the following information:
a. The particular line(s) where the service is connected
b. The FCC registration number as listed in Section 18.5
c. The ringer equivalence
d. The device make, model, and serial number
18.4 Phone Line Monitor
The XR500 Series panel has a built-in telephone monitor that monitors the phone line voltage to verify the
connection to the central office. Figure 11 and the table below identify the phone block pin layout, wire numbers,
and colors.
Wire Number
1
2
3
4
5
6
7
8
Wire Color
Gray
Orange
Black
Red
Green
Yellow
Blue
Brown
Digital Monitoring Products
20
To Telephone
Line
Ring
Tip
5
4
6
3
7
2
1
8
Ring 1
To Premise
Phone
RJ31X or RJ38X
Phone Block
Tip 1
Figure 11: Phone Jack Wiring
XR500 Series Installation Guide
Installation
The wires on the RJ31 that feed pins 4 and 5 should be the ONLY wires on the D-marc. All other house phone wiring
should be tied to pins 1 and 8 coming back from the RJ31.
Dial tone must come into RJ31X on pins 4 and 5 and go back to house phones from pins 1 and 8. Follow these steps
to determine if panel is seizing the line:
1.Unplug phone cord from RJ31X
2.Place butt-set on pins 4 and 5
3.Listen for dial tone. With dial tone present, lift either wire from pins 1 or 8
4.Listen for dial tone again. If the dial tone is present, RJ31X wiring is correct. If no dial tone is present, the
RJ31X wiring is backwards. Rewire so dial tone is coming IN on 4 and 5.
If you still have trouble with the phone line, you may need to replace the RJ cord. If the dial tone is still not
present, swap out the RJ31X phone block.
18.5 FCC Registration
The Model XR500 Series complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the
outside of the enclosure of this equipment is a label that contains, among other information, a product identifier in
the format US:CCKAL00BXR500. If requested this number must be provided to the telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the
applicable FCC Part 68 rules and requirements adopted by the ACTA. See installation instructions for details.
The Ringer Equivalence Number (REN) is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices
that may be connected to a line, as determined by the total RENs, contact the local telephone company.
If the XR500 Series causes harm to the telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company
will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC
if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect
the operation of the equipment. If this happens the telephone company will provide advance notice in order for you
to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with the Model XR500 Series, for repair or warranty information, please contact DMP at
the address and telephone number listed on the back of this document. If the equipment is causing harm to the
telephone network, the telephone company may request that you disconnect the equipment until the problem is
resolved.
If your premises has specially wired alarm equipment connected to the telephone line, ensure the installation
of the XR500 Series does not disable your alarm equipment. If you have questions about what will disable alarm
equipment, consult your telephone company or a qualified installer.
Caution: To ensure proper operation, this equipment must be installed according to the installation instructions in
this manual. To verify that the equipment is operating properly and can successfully report an alarm, this equipment
must be tested immediately after installation, and periodically thereafter, according to the test instructions in this
document and the XR500 Series Programming Guide (LT-0679). Additionally, verification of Line Seize capability
should be made immediately after installation, and periodically thereafter, in order to ensure that this equipment
can initiate a call even when other equipment (telephone, answering system, computer modem, etc.) connected to
the same line is in use.
XR500 Series Installation Guide
Digital Monitoring Products
21
Installation
Reset and Tamper Headers
19.1 J16 Reset Header
The reset header is located just above the terminal strip on the right side of the circuit board and is used to reset
the XR500 Series microprocessor. To reset the panel when first installing the system, install the reset jumper before
applying power to the panel. After connecting the AC and battery, remove the reset jumper.
To reset the panel while the system is operational, for example, prior to reprogramming, install the reset jumper
without powering down the system. Remove the reset jumper after one or two seconds.
After resetting the panel, begin programming within 30 minutes. If you wait longer than 30 minutes, you must reset
the panel again.
J3
Phone Line
J4
Tamper
Link LED
Activity LED
Momentarily place the Reset
jumper over both of the J16
pins to reset the panel.
J1
Ethernet
J21
RS-232
J22
LX-Bus
X
Output 1
J2
J10
Battery
Start
OVC
K6
J8
PROG
Output 2
Out1 Out2
Power J23
R
LED
L
AC AC +B –B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
1
2
3
4
5
6
7
8
9
J6
Interface
Card
Expansion
Connector
10
11
12 13
14
K7
J11
3
4
5
6
J16
Reset
Outputs 3-6
Z3 GND Z4 Z5 GND Z6
15 16
17 18
19
20
Z7 GND Z8 Z9+ Z9– Z10+ Z10–
21 22
23
24
25
26
27
28
Figure 12: XR500 Series Panel Showing the Reset Jumper
19.2 J4 Tamper Header
The J4 header is for use with the optional DMP 306 Tamper Harness. The harness connects to one or more tamper
switches mounted inside the panel enclosure to supervise against unauthorized enclosure opening or removal. Refer
to the wiring diagram on the enclosure door for correct tamper switch wiring.
How the Tamper Works
If the enclosure is opened or removed while one or more of the system areas are armed, a panel tamper alarm is
indicated. If all areas are disarmed, a panel tamper trouble is indicated.
Digital Monitoring Products
22
XR500 Series Installation Guide
Compliance
Listed Compliance Specifications
20.1 Introduction
For applications that must conform to a local authorities installation standard or a National Recognized Testing
Laboratory certificated system, please see the following sections.
Universal Burglary Specifications
21.1 Introduction
The programming and installation specifications contained in this section must be completed when installing the
XR500 Series panel in accordance with any of the burglary standards. Additional specifications may be required by a
particular standard. See the XR500 Series Programming Guide (LT-0679).
21.2 Wiring
All wiring must be in accordance with NEC, ANSI/NFPA 70, ANSI/UL 681, and ANSI/UL 827 for all burglary
installations.
21.3 Control Outside of Protected Area
A Potter EVD or Sentrol 5402 should be used in place of a lined cabinet when the panel is installed outside of the
protected area. Front and rear tamper switches are required. Refer to the system wiring diagram.
21.4 Police Station Phone Numbers
The digital dialer telephone number programmed for communication must not be a police station phone number.
21.5 Bypass Reports
The Bypass Reports option must be programmed as YES for all listed burglary applications.
21.6 System Maintenance
To ensure continuous satisfactory operation of any alarm system, proper installation and regular maintenance by the
installing alarm company and frequent testing by the end user is essential. Offering a maintenance program and
acquainting the user with the correct procedures for system use and testing is also the responsibility of the installing
alarm company.
21.7 Listed Receivers
Operation has been verified with the DMP SCS-1R, Sur-Gard SG-HLR2-DG, FBII CP220PB, Osborne-Hoffman QuickAlert, and Radionics D6500 receivers. It is the installer’s responsibility to verify compatibility between the XR500
Series and the receiver used during installation. The installer shall verify the compatibility of the receiver and the
system on a yearly basis.
21.8 Power Supply Supervision
For commercial burglary applications the power supply for all local bells shall be under 24-hour protection. Refer to
the Secondary Power Supply section in this document.
21.9 Wireless Tamper
The Zone Information Disarmed Open Message to Transmit must be programmed Trouble (T). (Not applicable to
ANSI/UL 1023).
21.10 Wireless External Contact
When used, the External Contact of 1101 or 1102 must be programmed Normally Closed.
21.11 Wireless Supervision Time
The Zone Information Supervision Time cannot be set to 0 (zero).
21.12 Detect Wireless Jamming
The Detect Wireless Jamming option must be programmed YES. (Not applicable to ANSI/UL 1023).
XR500 Series Installation Guide
Digital Monitoring Products
23
Compliance
Area Information
22.1 Ownership
The control unit system shall be under one ownership.
22.2 Annunciation
The System shall be installed so that when arming any area from any keypad, the local bell shall annunciate.
22.3 Trouble Display
The Status List programming shall be set to annunciate all trouble messages at all keypads.
22.4 Closing Wait
The Closing Wait option must be programmed YES.
22.5 Local Bell Supervision
When a local bell is employed, the power supply for the bell shall be under 24-hour protection. Proper personnel for
maintenance or security of the system shall be able to disarm that area.
Household Burglar-Alarm System Units
ANSI/UL 1023
23.1 Audible Devices
At least one listed audible device (Ademco AB12M) rated to operate over the voltage rate of 11.7 VDC to 12.8 VDC
and rated at 85 DB minimum must be used.
23.2 Auxiliary Circuits
At least one burglary alarm initiating device shall be used on the system. If the voltage for the device is applied
by the control unit the burglary alarm initiating device shall be rated to operate over the range of 11.5 VDC to
12.7 VDC.
23.3 Bell Cutoff
The Bell Cutoff time cannot be less than five minutes.
23.4 Entry Delay
The maximum entry delay used must not be more than 45 seconds.
23.5 Exit Delay
The maximum exit delay used must not be more than 60 seconds. .
23.6 Weekly Test
The product should be tested weekly.
23.7 Wireless Audible Annunciation Option
The Wireless Audible option must be selected as DAY for residential applications.
Central-Station and Proprietary Burglar-Alarm Units
ANSI/UL 1610 AND ANSI/UL 1076
24.1 Opening/Closing Reports
The Opening/Closing Reports option must be programmed as YES. .
24.2 Closing Wait
The Closing Wait option must be programmed YES.
24.3 Entry Delay
The maximum entry delay used must not be more than 60 seconds when using Model 350A or 350H Attack Resistant
Housing.
Digital Monitoring Products
24
XR500 Series Installation Guide
Compliance
24.4 Exit Delay
The maximum exit delay used must not be more than 60 seconds.
24.5 Proprietary Dialer
The Model XR500 Series provides proprietary service when configured as a digital dialer.
24.6 DACT Central Station
DACT Central Station service can be provided under by adding an Ademco AB12M bell and bell housing and placing
the Model XR500 Series panel into Model 350A or 350H Attack Resistant Housing.
24.7 Bell Cutoff
The Bell Cutoff time cannot be less than 15 minutes.
24.8 Standard or Encrypted Line Security
Standard Line Security is provided when configured as a Path 1 NET system using an XR500N panel or an XR500
panel with an iCOM™ Network Alarm Router (232). The NET Check-in time must be set to 06 minutes or RND When
programmed for Standard Line Security, Exit Time Restart is disabled. When a dialer is required for 06 minute
check-in time, an attack resistant enclosure (DMP Model 350A or 350H) is required. When the check-in time is set to
a number less than 200 seconds, an attack resistant enclosure is not required.
To provide Encrypted Line security, install an XR500E panel or an XR500 panel with an iCOM-E™ Encrypted Network
Alarm Router.
For Encrypted Line security operation, communication between the Premise and Supervising Station provides 128 bit
encryption when using an XR500E panel or an XR500 panel with an iCOM-E Encrypted Network Alarm Router.
The XR500 Series Protected Premises Control Unit is suitable for Standard Line Security service when configured for
NET communication with SCS-1R receiving system. This configuration is approved for the following:
AMCX - Central Station Alarm Units
APOU - Proprietary Alarm Units
24.9 Wireless Audible Annunciation Option
The Wireless Audible option must be selected as ANY for commercial applications.
24.10 Model 463G or CellCom, CELL Only, Standard or Encrypted Line Security
Standard or Encrypted Line Security is provided when programmed using CELL with no backup. XR500 cellular
communication is used as primary with a 3 minute check-in when armed or disarmed.
Path 1 programming
Comm Type: = CELL
Checkin: = 3 minute
Path Type: = Primary
Fail Time: = 3 minute
Encrypt: = NO or YES*
Test Rpt: = NO
Sub Code: = NO or YES
*For Encrypted Line Security, program a Passphrase in Network Options.
XR500 Series Installation Guide
Digital Monitoring Products
25
Compliance
24.11 Model 463G or CellCom, NET with CELL as Alternate Primary and Dialer Backup,
Standard or Encrypted Line Security
Standard or Encrypted Line Security is provided using NET communication with CELL as an alternate primary and
with digital dialer as a backup. XR500 network communication is used as primary with a 6 minute check-in when
armed, and a random check-in over a 60 minute period when disarmed. CELL is the backup path and set to daily
test. Should the NET primary path become disabled, CELL adapts the same check-in time programmed for the
primary communication and becomes an alternate primary path. The dialer path is used as the backup if both NET
and CELL fail to receive acknowledgement from the receiver.
This method of operation causes the CELL alternate primary to adapt to the 6 minute NET primary check-in rate
when the NET primary is unavailable maintaining line supervision and precludes the need for a central station runner
to respond to the NET primary failure.
Path 1 programming
Comm Type: = NET
Path Type: = Primary
Test Rpt: = NO
Checkin: = 6 minute, or RND (random)
Fail Time: = 6 minute, or RND (random)
Encrypt: = NO or YES*
Sub Code: = YES
Path 2 programming
Comm Type: = CELL
Path Type: = Backup (operates as
alternate primary)
Test Rpt: = YES
Test Freq: = Daily
Checkin: = ADAPT
Encrypt: = NO or YES*
Sub Code: = Shared
Path 3 programming
Comm Type: = DD
Path Type: = Backup (operates
as second method)
Test Rpt: = YES
Test Freq: = Daily
Duplicate Alarms: = YES
*For Encrypted Line Security, program a Passphrase in Network Options.
24.12 Model 463G or CellCom, NET with CELL as Backup and Adaptive Primary,
Standard or Encrypted Line Security
Standard or Encrypted Line Security is provided when programmed using NET communication and CELL as backup
and as needed adapts and takes over as primary. XR500 network communication is used as primary with a 6 minute
check-in when armed, and a random check-in over a 60 minute period when disarmed. CELL is the backup path and
set to daily test. Should the primary path become disabled, the CELL adapts to a special 3 minute check-in time and
because of that check-in rate becomes the primary without the requirement of an additional backup. This method
of operation causes the CELL backup to adapt to the 3 minute check-in rate when the NET primary is unavailable
becoming a standalone primary without the need for a backup. This maintains line supervision and precludes the
need for a central station runner to respond to the NET primary failure.
Path 1 programming
Path 2 programming
Comm Type: = NET
Comm Type: = CELL
Path Type: = Primary
Path Type: = Backup (operates as second method)
Test Rpt: = NO
Test Rpt: = YES
Checkin: = 6 minute, or RND (random)
Test Freq: = Daily
Fail Time: = 6 minute, or RND (random)
Checkin: = ADAPT3
Encrypt: = NO or YES*
Encrypt: = NO or YES*
Sub Code: = YES
Duplicate Alarms: = YES
Sub Code: = Shared
*For Encrypted Line Security, program a Passphrase in Network Options.
Digital Monitoring Products
26
XR500 Series Installation Guide
Compliance
Holdup Alarm Units
ANSI/UL 636
25.1 ANSI/UL 1610 Required
The programming and installation specifications contained in this section must be completed in addition to ANSI/UL
1610 Specifications when installing a Model 1142 with a Model XR500 Series panel.
25.2 1100X Wireless Receiver
The Model 1100X Wireless Receiver in conjunction with the Model 1142 Holdup Alarm Transmitter must be installed
in the system.
25.3 Wireless Supervision Time
The Zone Information Supervision Time must be a maximum of 240 minutes.
25.4 LED Display
The LED Operation option display must be set to NO when using a Model 1142 Holdup Alarm Transmitter.
25.5 Jamming Detection
The Detect Wireless Jamming option must be set to YES.
25.6 Local Alarm
The Bell Action for a PN (Panic) type zone must be programmed as N (None).
25.7 Message to Transmit
The Armed Open and Armed Short messages for a PN (Panic) type zone must be programmed to A (Alarm).
25.8 Wireless Audible Annunciation Option
The Wireless Audible option must be selected as ANY for commercial applications.
Digital Burglar Alarm Communicator System Units
ANSI/UL 1635
26.1 System Trouble Display
The Status List Display must include at least one keypad that displays system monitor troubles.
26.2 Digital Dialer Telephone Number
Both programmed telephone numbers must begin with a P.
26.3 Test Time
The Test Time option must be programmed so that the XR500 Series sends a report once every 24 hours.
26.4 Closing Wait
The Closing Wait option must be programmed YES.
Police Station Connected and Local Burglar Alarm Units
ANSI/UL 365
27.1 System Trouble Display
The Status List Display must include at least one keypad that displays system monitor troubles.
27.2 Entry Delay
The maximum entry delay used must not be more than 60 seconds when using Model 350A or 350H Attack housing.
27.3 Exit Delay
The maximum exit delay used must not be more than 60 seconds.
XR500 Series Installation Guide
Digital Monitoring Products
27
Compliance
27.4 Bell
A local audible signal appliance must be used such as Ademco AB12M bell and bell housing.
The alarm housing for a mercantile alarm system without a remote alarm transmission connection shall be mounted
on the outside of the building, visible from a public street or highway. It shall be accessible for examination and
repair. It shall also be located not more than four stories above the street level unless:
a) A second alarm sounding device and housing, intended for outside service, is mounted adjacent to the premises or
area of the building in which the alarm system is installed or
b) A second alarm sounding device, intended for inside service, is mounted within the premises.
In either case, the outside alarm sounding device and housing may be mounted as high as the seventh floor.
27.5 Bell Cutoff
The Bell Cutoff time cannot be less than 15 minutes.
27.6 Automatic Bell Test
The Automatic Bell Test option must be programmed as YES.
27.7 Standard or Encrypted Line Security
Standard Line Security is provided when configured as a Path 1 NET system using an XR500N panel or an XR500 panel
with an iCOM™ Network Alarm Router. The NET Check-in time must be set to 06 minutes or RND When programmed
for Standard Line Security, Exit Time Restart is disabled. When a dialer is required for 06 minute check-in time, an
attack resistant enclosure (DMP Model 350A) is required. When the check-in time is set to a number less than 200
seconds, an attack resistant enclosure is not required.
To provide Encrypted Line security, install an XR500E panel or an XR500 panel with an iCOM-E™ Encrypted Network
Alarm Router.
For Encrypted Line security operation, communication between the Premise and Supervising Station provides 128 bit
encryption when using an XR500E panel or an XR500 panel with an iCOM-E Encrypted Network Alarm Router.
27.8 Wireless Audible Annunciation Option
The Wireless Audible option must be selected as ANY for commercial applications.
27.9 Model 463G or CellCom, CELL Only, Standard or Encrypted Line Security
Standard or Encrypted Line Security is provided when programmed using CELL with no backup. XR500 cellular
communication is used as primary with a 3 minute check-in when armed or disarmed.
Path 1 programming
Comm Type: = CELL
Checkin: = 3 minute
Path Type: = Primary
Fail Time: = 3 minute
Encrypt: = NO or YES*
Test Rpt: = NO
Sub Code: = NO or YES
*For Encrypted Line Security, program a Passphrase in Network Options.
Digital Monitoring Products
28
XR500 Series Installation Guide
Compliance
27.10 Model 463G or CellCom, NET with CELL as Alternate Primary and Dialer Backup,
Standard or Encrypted Line Security
Standard or Encrypted Line Security is provided using NET communication with CELL as an alternate primary and
with digital dialer as a backup. XR500 network communication is used as primary with a 6 minute check-in when
armed, and a random check-in over a 60 minute period when disarmed. CELL is the backup path and set to daily
test. Should the NET primary path become disabled, CELL adapts the same check-in time programmed for the
primary communication and becomes an alternate primary path. The dialer path is used as the backup if both NET
and CELL fail to receive acknowledgement from the receiver.
This method of operation causes the CELL alternate primary to adapt to the 6 minute NET primary check-in rate
when the NET primary is unavailable maintaining line supervision and precludes the need for a central station runner
to respond to the NET primary failure.
Path 1 programming
Comm Type: = NET
Path Type: = Primary
Test Rpt: = NO
Checkin: = 6 minute, or RND (random)
Fail Time: = 6 minute, or RND (random)
Encrypt: = NO or YES*
Sub Code: = YES
Path 2 programming
Comm Type: = CELL
Path Type: = Backup (operates as
alternate primary)
Test Rpt: = YES
Test Freq: = Daily
Checkin: = ADAPT
Encrypt: = NO or YES*
Sub Code: = Shared
Path 3 programming
Comm Type: = DD
Path Type: = Backup (operates
as second method)
Test Rpt: = YES
Test Freq: = Daily
Duplicate Alarms: = YES
*For Encrypted Line Security, program a Passphrase in Network Options.
27.11 Model 463G or CellCom, NET with CELL as Backup and Adaptive Primary,
Standard or Encrypted Line Security
Standard or Encrypted Line Security is provided when programmed using NET communication and CELL as backup
and as needed adapts and takes over as primary. XR500 network communication is used as primary with a 6 minute
check-in when armed, and a random check-in over a 60 minute period when disarmed. CELL is the backup path and
set to daily test. Should the primary path become disabled, the CELL adapts to a special 3 minute check-in time and
because of that check-in rate becomes the primary without the requirement of an additional backup. This method
of operation causes the CELL backup to adapt to the 3 minute check-in rate when the NET primary is unavailable
becoming a standalone primary without the need for a backup. This maintains line supervision and precludes the
need for a central station runner to respond to the NET primary failure.
Path 1 programming
Path 2 programming
Comm Type: = NET
Comm Type: = CELL
Path Type: = Primary
Path Type: = Backup (operates as second method)
Test Rpt: = NO
Test Rpt: = YES
Checkin: = 6 minute, or RND (random)
Test Freq: = Daily
Fail Time: = 6 minute, or RND (random)
Checkin: = ADAPT3
Encrypt: = NO or YES*
Encrypt: = NO or YES*
Sub Code: = YES
Duplicate Alarms: = YES
Sub Code: = Shared
*For Encrypted Line Security, program a Passphrase in Network Options.
Police Station Connected and Local Burglar Alarm Units
ANSI/UL 609
28.1 Mercantile
For Mercantile and Police Station Connect operation the Model XR500 Series must be mounted in an Attack Resistant
Housing, (DMP Model 350A or 350H).
28.2 Entry Delay
The maximum entry delay used must not be more than 60 seconds when using the Model 350A or 350H housing.
28.3 Exit Delay
The maximum exit delay used must not be more than 60 seconds.
XR500 Series Installation Guide
Digital Monitoring Products
29
Compliance
28.4 Mercantile Safe and Vault
When the DMP Model 350A or 350H Attack housing is used, the XR500 Series provides operation as a mercantile safe
and vault alarm. Bell Supervision and wiring must be in accordance with ANSI/UL 681. When the XR500 Series is
mounted outside the safe or vault, tamper protection and the Sentrol Model 5402 or Potter EVD listed vibration
detectors should be used.
28.5 Bell
A local audible signal appliance must be used such as Ademco AB12M bell and bell housing.
In a mercantile burglar alarm system, a mercantile alarm sounding device located within a building but outside the
protected area, is acceptable, provided it is rated for outside service and alarm conditions are transmitted to:
a) The dispatch location of the law enforcement agency having jurisdiction over the protected property or
b) A central station or residential monitoring station complying with the Standard for Central Station Alarm Services,
UL 827.
In a mercantile burglar alarm system, an alarm sounding device located within the area of greatest protection, or
outside the area of greatest protection but within an area protected by an alarm system and that shares a common
control unit with the system installed in the area of greatest protection, is acceptable provided it is rated for inside
service and alarm conditions are transmitted to:
a) The dispatch location of the law enforcement agency having jurisdiction over the protected property or
b) A central station or residential monitoring station complying with the Standard for Central Station Alarm Services,
UL 827.
An inside sounding device shall be mounted at least 10 feet (3.05 m) above the floor or at the surface of the ceiling.
When there is fixed construction within the area that could provide access for an intruder, the alarm sounding
device shall also be mounted at least 4 feet (1.2 m), as measured horizontally, away from the edges of the fixed
construction or at least 10 feet (3.05 m) above it so as to minimize access by an intruder.
28.6 Bank Safe and Vault (XR500N/XR500E only)
The Bank Safe and Vault option must be programmed as YES. The 72 hour battery standby must be provided. A
Rothenbuhler Model 5110 High Security Bell must be used.
28.7 Wireless Audible Annunciation Option
The Wireless Audible option must be selected as ANY for commercial applications.
Access Control System Units
ANSI/UL 294
29.1 Panel Designation
The XR500 Series panels are designated stand alone units.
29.2 Tamper Protection
For listed Access Control installations, a tamper switch must be used.
29.3 Compatible Devices
The following devices are compatible with the XR500 Series panels.
Access Control
733 Wiegand Interface Module
Proximity reader connector
734 Wiegand Interface Module
Proximity reader connector
OP-08CB Motion Detector
Infrared sensor
* PB-2 REX Button
Exit control push button
PP-6005B Proxpoint Plus® Reader
Proximity reader
MP-5365 Miniprox® Reader
Slimline proximity reader
PR-5455 ProxPro® II Reader
Long range reader with sounder
MX-5375 Maxi-Prox™ Reader
Long range reader compatible with 1351 Prox Pass
* This device has not been investigated and shall not be used in listed installations.
Digital Monitoring Products
30
XR500 Series Installation Guide
Compliance
Universal Fire Alarm Specifications
30.1 Introduction
The programming and installation specifications contained in this section must be completed when installing the
Model XR500 Series in accordance with any of the ANSI/UL or NFPA fire standards. Additional specifications may be
required by a particular standard. See the XR500 Series Programming Guide (LT-0679).
30.2 Wiring
All wiring must be in accordance with NEC, ANSI/NFPA 70.
30.3 Transformer
Use the Model 322 or 323 wire-in 16 VAC 56 VA transformer mounted within 20 feet of the panel and connected by
conduit.
30.4 End-of-Line Resistor
The DMP Model 310 1k Ohm EOL resistor should be used on all 1k Ohm EOL fire zones.
30.5 System Trouble Display
The Status List Display must include at least one keypad that displays system monitor troubles.
30.6 Fire Display
The Status List Display must include at least one keypad that displays troubles and alarms on fire type zones.
30.7 Police Station Phone Number
The digital dialer telephone number programmed for communication must not be a police station phone number,
unless that phone number is specifically provided for that purpose.
30.8 System Maintenance
To ensure continuous satisfactory operation of any alarm system, proper installation and regular maintenance by the
installing alarm company and frequent testing by the end user is essential. Offering a maintenance program and
acquainting the user with the correct procedures for system use and testing is also the responsibility of the installing
alarm company.
30.9 Audible Alarm
Fire Type zones must be programmed to activate an audible alarm. The Bell Action for Fire Type zones must not be
programmed as N (None).
30.10 Fire Zone Programming
If a retard delay is used on a waterflow zone, it cannot exceed 90 seconds and any retard delay in the waterflow
initiating devices must be subtracted from the 90 seconds al­lowed. The retard delay should not be used on a zone
with smoke detectors.
30.11 Class A Style D Zones
If required, the DMP 869 Dual Style D Initiating Module provides for connection of two Class A Style D zones to the
Model XR500 Series. See the 869 Installation Guide (LT-0186) and this guide for wiring information.
30.12 Listed Receivers
Use the DMP SCS-1R (SDLC), Sur-Gard SG-HLR2-DG (CID), FBII CP220PB (CID), and Osborne-Hoffman Quick-Alert (CID)
receivers.
XR500 Series Installation Guide
Digital Monitoring Products
31
Compliance
Control Units for Fire-Protective Signaling Systems
ANSI/UL 864, NFPA 72
31.1 Power Supply
For listed installations, the total current combined from Auxiliary and Bell Power cannot exceed:
1.2 Amps with a 56 VA transformer; .5 Amp Max for Auxiliary Power and .7 Amp Max for Bell
For listed installations, the 50 VA Plug-in transformer cannot be used.
The total combined current from Terminals 7, 11, 25, and 27 cannot exceed 1.2 Amps.
31.2 Zone Restoral Reports
The Restoral Reports option must be selected as YES or Disarm.
31.3 Power Fail Delay
The Power Fail Delay option must be selected as required by the service of the panel. For Central Station or Remote
Station service: 1.
31.4 Sprinkler Supervisory
Any zone used for sprinkler supervisory must be programmed with “SPRINKLR XXX” as the zone name. The last three
characters in the zone name may be assigned a number to identify the zone. The Model 893A Dual Phone Line Module
must be used on all sprinkler supervisory systems.
31.5 DACT Systems
A DACT system may be configured as one of the following:
Path 1 Type DD Primary and Path 2 Type DD Backup
Path 1 Type DD Primary and Path 2 Type CELL Backup
Path 1 Type DD Primary and Path 2 Type NET Backup
Path 1 Type DD Primary and Path 2 Type DD Backup
Use two telephone lines and the Model 893A Dual Phone Line Module to provide two phone line connections to the
system. Two different telephone numbers must be programmed for digital communication. Do not connect to
ground start or party lines.
Path 1 Programming
Path 2 Programming
Comm Type = DD
Comm Type = DD
Path Type = Primary
Path Type = Backup
Test Rpt = Yes
Test Rpt = Yes
Test Freq = 1 Dy
Test Freq = 1 Dy
893A = Yes
Path 1 Type DD Primary and Path 2 Type CELL Backup
When using a telephone line and a GSM cellular as backup,
Path 1 Programming
Path 2 Programming
Comm Type = DD
Comm Type = CELL
Path Type = Primary
Path Type = Backup
Test Rpt = Yes
Test Rpt = Yes
Test Freq = 1 Dy
Test Freq = 1 Dy
Receiver IP Address
First GPRS APN
Path 1 Type DD Primary and Path 2 Type NET Backup
When using a telephone line and a Network IP as backup,
Path 1 Programming
Path 2 Programming
Comm Type = DD
Comm Type = NET
Path Type = Primary
Path Type = Backup
Test Rpt = Yes
Test Rpt = Yes
Test Freq = 1 Dy
Test Freq = 1 Dy
Receiver IP Address
Digital Monitoring Products
32
XR500 Series Installation Guide
Compliance
31.6 Local Protective Signaling Systems
The DMP Model 865, 866, or 867 Notification Circuit Module must be used on the bell circuit for detection of shorts
and grounds. Any burglary or other off premises communication must be done with the Model 893A Dual Phone Line
Module. For local commercial fire installations, the 893A is required. 31.7 Remote Station Protective Signaling Systems
You must provide 60 hours of standby battery. See section 6.9 in this guide for standby battery calculations. Two
Radionics Model D127 Reversing Relay Modules provide two reversing polarity telephone connections. See the D127
Installation Instruction sheet for wiring details. A DMP Model 893A is used to provide two line dialer communication.
31.8 Fire Protective Signaling Systems using Internet/Intranet/Cell Networks
An Other Transmission Technologies system as defined in UL 864 9th Edition, Section 40.7 may be configured as NET
Primary using a hardwire IP network or CELL Primary using a Model 463G Digital Cellular Communicator with or
without a backup path. The system may be configured as one of the following:
Path 1 Type NET or CELL Primary with no Backup
Path 1 Programming
Comm Type = NET or CELL Checkin Min = 3
Path Type = Primary
Failtime Min = 5
Test Rpt = No
Sub Code = Yes
Checkin = Yes
Send Comm Trbl = Yes
Path 1 Type NET Primary and Path 2 Type DD Backup
Path 1 Programming
Path 2 Programming
Comm Type = NET
Comm Type = DD
Path Type = Primary
Path Type = Backup
Test Rpt = Yes
Test Rpt = Yes
Test Freq = 1 Dy
Test Freq = 1 Dy
Send Comm Trbl = Yes
Send Comm Trbl = Yes
Comm Path Trbl = Yes (Status List Programming)
Path 1 Type NET Primary and Path 2 Type CELL Backup
Path 1 Programming
Path 2 Programming
Comm Type = NET
Comm Type = CELL
Path Type = Primary
Path Type = Backup
Test Rpt = Yes
Test Rpt = Yes
Test Freq = 1 Dy
Test Freq = 1 Dy
Send Comm Trbl = Yes
Send Comm Trbl = Yes
Comm Path Trbl = Yes (Status List Programming)
Path 1 Type CELL Primary and Path 2 Type NET Backup
Path 1 Programming
Path 2 Programming
Comm Type = CELL
Comm Type = NET
Path Type = Primary
Path Type = Backup
Test Rpt = Yes
Test Rpt = Yes
Test Freq = 1 Dy
Test Freq = 1 Dy
Send Comm Trbl = Yes
Send Comm Trbl = Yes
Comm Path Trbl = Yes (Status List Programming)
XR500 Series Installation Guide
Digital Monitoring Products
33
Compliance
31.9 Combination Systems
For combination fire and burglary systems, powered burglary devices (PIR, Glassbreak, etc.) must be powered from a
separate listed power supply (DMP Model 505-12). This requirement is not needed for non-powered burglary devices
(door contacts, etc.) which only connect to the zone input of zone expanders or keypads. Refer to Powered Burglary
Devices later in this document.
For combination fire and burglary systems, burglary sounding devices such as sirens and bells must be energized
using panel relays, 860 relays, or 716 relays. Programming the output to activate the relay must occur using the
Burglary Bell Output option in Area Information or by the Alarm Action output option of Zone Information. The
Burglary Bell Action option of the panel Bell Options must be programmed as None.
31.10 Remote Annunciators
At least one Model 630F Remote Annunciator must be used on the system. All fire alarms, fire troubles and
supervisory alarms or troubles must be annunciated only on the 630F. All burglary alarms or troubles must only be
annunciated on non-fire keypads. See Status List options of the XR500 Series Programming Guide (LT-0679).
31.11 Notification Appliances
The following table indicates the approved notification appliances that can be used with the XR500 Series system.
Wheelock Model No.
MT-12/24
MB-G6-12
MB-G10-12
RSS-121575W-F
RSSP-121575W-F
NS-121575W-F
SM-12/24-R
DSM-12/24-R
Description
Multi-tone Horn
Bell, 6 inch
Bell, 10 inch
Strobe, 15/75 candela
Strobe, w/retrofit plate
Horn Strobe, 15/75 candela
Sync Module, Single circuit
Sync Module, Dual circuit
Max No. of Appliances using 56 VA
8
16
16
5
5
5
31.12 Cross Zoning
When using cross zoning, there must be a minimum of two detectors installed in each protected space and the
detector installation spacing must be 0.7 times the linear spacing in accordance with National Fire Alarm Code,
NFPA 72.
31.13 Ground Fault
For supervised circuits, ground fault is detected at 0 (zero) Ohms.
31.14 Wireless Testing
When using the 1100X Wireless Receiver for Fire Protective Signaling, after all transmitters are in position, the WLS
option of the panel’s Walk Test must be operated and all transmitters programmed for Fire (FI) or Supervisory (SV)
must show that their checkin message was received.
Household Fire Warning System Units
ANSI/UL 985, NFPA 72
32.1 Bell Output Definition
The Model XR500 Series panel Bell Output must be programmed to operate steady on burglary alarms and pulsed or
temporal on fire alarms.
32.2 Audible Devices
At least one listed audible device rated to operate over the voltage rate of 11.7 VDC to 12.8 VDC and rated at 85 DB
minimum must be used.
32.3 Auxiliary Circuits
At least one fire alarm initiating device shall be used on the system. If the voltage for the device is applied by the
control unit the fire alarm initiating device shall be rated to operate over the range of 11.5 VDC to 12.7 VDC.
Digital Monitoring Products
34
XR500 Series Installation Guide
Compliance
32.4 Bell Cutoff
The Bell Cutoff time cannot be less than five minutes.
32.5 Detect Wireless Jamming
The Detect Wireless Jamming option must be programmed YES.
32.6 Wireless External Contact
When used, the External Contact of 1101 or 1102 must be programmed Normally Closed.
32.7 Wireless Supervision Time
The Zone Information Supervision Time must be 240 minutes.
32.8 Wireless Fire Verification
When used, the Model 1161 and 1162 wireless smoke detectors must not be programmed as Fire Verification (FV)
zone type.
California State Fire Marshal Specifications
33.1 Bell Output Definition
The Model XR500 Series panel Bell Output must be programmed to operate steady on burglary alarms and pulsed,
temporal, or California School Code on fire alarms.
New York City (MEA) Specifications
34.1 Introduction
The programming and installation specifications contained in this section must be completed when installing the
XR500 Series panel for New York City (MEA) fire alarm installations that provide a digital dialer with network IP
communication as backup. Fire alarm installations that use two digital dialer telephone lines do not need to comply
with these specifications.
34.2 Digital Dialer and Network Communication
When used with a central office communicator or a transmitter, the installation and operation of the equipment and
devices shall comply with 3RCNY 17-01. The installation shall employ the digital dialer as the primary communicator
(using telephone line) with network IP communication as backup or secondary means of communication. It shall
have the capability of transmitting separate and distinct signals to indicate manual pull station alarm, automatic
detection alarm, sprinkler waterflow alarm, supervisory signal indications and trouble indications.
34.3 Wiring
All wiring must be in accordance with NEC, ANSI, and NFPA 70. All network cabling must be installed in accordance
with NFPA 70 for communication circuits.
34.4 Communication Programming
For digital dialer communication with supervised network backup, program the following:
PRIMARY COMM TYPE = DD
FIRST PHONE NUMBER = Central Station Receiver Phone Number
BACKUP COMM TYPE = NET
RECEIVER
ALARMS = YES
34.5 Additional Requirements
Program and install the equipment to comply with NFPA basic fire requirements. Refer to the Universal Fire Alarm
Specifications and ANSI/UL 864 NFPA 72 Specifications in this document.
XR500 Series Installation Guide
Digital Monitoring Products
35
Compliance
False Alarm Reduction Programmable Options *
35.1 Shipping Defaults and Recommended Programming for ANSI/SIA CP-01-2000
DMP XR500
PROGRAMMING
GUIDE LT‑0679
SECTION #
SIA CP-01 FEATURE
PARAGRAPH # AND
DESCRIPTION
REQUIREMENT
RANGE
4.2.2.1 Exit Time
15.2 Exit Delay
Required
45 sec. - 250 sec.
(Programmable)
4.2.2.2 Progress
Annunciation
15.2 Exit Delay
Allowed
4.2.2.3 Exit Time
Restart
15.2 Exit Delay
Required Option
4.2.2.5 Auto Stay Arm
on Unvacated Premises
SHIPPING
DEFAULT
RECOMMENDED
PROGRAMMING*
60
Seconds
60 Seconds
Individual keypads
may be disabled per
zone
All
keypads
enabled
All keypads enabled
For re-entry during
exit time
Enabled
Enabled
Required Option
Area 1 = Perimeter
(except for
Area 2 = Interior
Install Guide (LT-0681) remote arming)
Enabled
Enabled for
Residential
Applications
33.3 Occupied
Premise - See XR500
4.2.4.4 Exit Time and
Progress Annunciation/
Disable - for Remote
Arm
Not Available on
Remote Arming
Allowed Option
4.2.3.1 Entry Delay(s)
8.3 Entry Delay
Required
30 sec. – 240 Sec. **
(Programmable)
Progress Annunciation
Not
Always disabled for
Available
Remote Arming
Remote Arming not
allowed for CP-01
installations.
30
Seconds
At least 30 Seconds **
4.2.5.1 Abort Window –
3.7 Transmit Delay
for Non‑Fire Zones
Required Option
Disable by zone or
zone type
Enabled
NT DY
EX Zone
Enabled
4.2.5.1 Abort Window
Time – for Non-Fire
Zones
3.7 Transmit Delay
Required
(Programmable
15 sec. - 45 sec. **
30
Seconds
At least 15 Seconds **
4.2.5.1.2 Abort
Annunciation
3.7 Transmit Delay
Annunciate that
Required Option no alarm was
transmitted (S45)
Yes
Yes
4.2.5.4.1 Cancel
Annunciation
Annunciate that
Always Enabled - Not
Required Option a Cancel was
Programmable
transmitted (S49)
Always
Enabled
Yes
4.2.6.1 & 4.2.6.2
Duress Feature
User Code + 1 =
Ambush Code Not
Available
4.3.1 Cross Zoning
Allowed Option
No 1 + derivative of
Code +1
another user code/no
Always
duplicates with other
Disabled
user codes
Not Programmable
16.22 Cross Zone
Required Option
Yes/No Zone
Programming
No
Enabled using two or
more programmed
zones
4.3.1 Programmable
Cross Zoning Time
8.4 Cross Zone Time
Allowed
4 sec. - 250 sec.
4 Seconds
Per walk path in
protected premises
4.3.2 Swinger Shutdown
8.7 Swinger Bypass
Trips
For all non-fire
Required
zones, shut down at
(Programmable)
1 or 2 trips
One (1)
trip
One (1) trip
Yes
Enabled (all zones)
No
Yes as required
(unless sensors can
self verify)
Disabled
Enabled if user has
call waiting
4.3.2 Swinger Shutdown
16.16 Swinger Bypass Allowed
Disable
For non-police
response zones
4.3.3 Fire Alarm
Verification
16.4 Zone Type
Required Option FV Type Zone
4.5 Call Waiting Cancel
3.19 Telephone
Number
Required Option
Include *70P in
Telephone Number
* Programming at installation may be subordinate to other listed requirements for the intended application.
** For listed Installations, combined Entry Delay and Transmit Delay should not exceed 1 minute.
Digital Monitoring Products
36
XR500 Series Installation Guide
Compliance
False Alarm Reduction Programmable Options (continued)
35.2 Call Waiting (ANSI/SIA CP-01-2000)
The Call Waiting default setting is disabled. To cancel the Call Waiting feature, program * (star) 7 0 P (pause), the
standard telephone code prefix that cancels call waiting, into the telephone number string. Cancel Call Waiting for
telephone lines that have Call Waiting operational on the telephone line. See the XR500 Series Programming Guide
(LT‑0679).
Caution: A call waiting cancel programmed on a non-call waiting telephone line, would prevent
communication to the central station.
35.3 Occupied Premise (ANSI/SIA CP-01-2000)
When only two areas are used, and area one is named Perimeter, and area two is named Interior, and no exit type
zone transition occurs during the exit delay because the premise continues to be occupied, the Interior area will
automatically disarm at the end of the exit delay.
35.4 Entry Delay (ANSI/SIA CP-01-2000)
Only use Entry Delay 1. Do not use Entry Delay 2, 3, or 4. See the XR500 Series Programming Guide (LT-0679).
35.5 Minimum Installation Requirements (ANSI/SIA CP-01-2000)
SIA CP-01-2000 minimum system installation requirements include an XR500, a listed local Bell, and off premise
DACT communication to an SCS-1R receiver plus one of the following compatible keypads.
630F Fire Command™ Center
690, 790, 639/793 Security Command™ keypads
7060, 7063, 7070, or 7073 Thinline™ keypads
7060A, 7063A, 7070A, or 7073A Aqualite™ keypads
7160, 7163, 7170, or 7173 Thinline™ keypads
7760 Clear Touch™ keypad
ULC S304 Specifications
Signal Receiving Center and Premise Burglar Alarm Control Units
36.1 Level V Communication
Level V communication channel security is provided for Internet, Intranet, LAN or WAN networks when configured as
a NET communicating system using the XR500N. Additionally, the following options must be programmed in XR500
Series panel Communication:
SUB CODE:
CHECKIN TIME:
FAIL TIME: SEND COMM TRBL:
TCP COMM:
YES
2 MINUTES
3 MINUTES
YES
YES
In addition, the SCS-101 Network Line Card installed in the SCS-1R Receiver must have the ACK Substitution Message
programmed as NO.
XR500 Series Installation Guide
Digital Monitoring Products
37
Wiring Diagrams
Wiring Diagrams
37.1 866 with NAC Extender
To panel zone
To panel alarm output
To panel terminal 7
To panel zone
To panel terminal 10
Normal/Silence Switch
DMP Model 866
45mA @ 12 VDC
The 866 Notification
Appliance Circuit
Module in alarm draws
up to 31mA through
its Terminal 3 Alarm
Input and 45mA from
its Terminal 1 Aux
Power Input.
See the 866
Installation (LT-0059)
1
2
3
4
5
6
7
8
Model 310
1K EOL
Model 310
1K EOL
AUX PWR
GND
Alarm In
Bell PWR In
Bell Out +
Bell Out Bell Trouble
Bell Trouble
Note: Terminals 3
and 4 jumper together
to supply Bell Power
from the panel
PowerPath NAC Extender
Models
PS-8
PS-8E
PS-6
PS-6E
Normal/Silence Switch
1
2
3
4
5
6
7
8
See PowerPath installation for
detailed connection
instructions
AUX PWR
GND
Alarm In
Bell PWR In
Bell Out +
Bell Out Bell Trouble
Bell Trouble
The Bell Output programming for Fire type zones must be set to Steady
Digital Monitoring Products
38
XR500 Series Installation Guide
Wiring Diagrams
37.2 866 Class B Style W using Single Notification Appliance
J1
P3
J4
Tamper
J3
Phone Line
PANEL
MAIN
F2
J4
BACKUP
J2
J5
J6 Interface
Card
Expansion
Connector
XR500 Series Command
Processor™ Panel
F1
K1
J1
Ethernet
K2
J21
J23
RS-232
L
X
J22
LX-Bus
P10
–
+
Output 2
Output 1
DS1
Buzzer
J10
J2
Battery
Start
K6
Out2
Power LED R
J11
K7
3
4
5
6
J8
PROG
AC
AC
+B
-B
1
2
3
4
BELL GND RED YEL
5
6
7
GRN BLK
8
9
SMK GND
10
11
12
Z1
GND
Z2
Z3
GND
Z4
Z5
GND
Z6
Z7
GND
Z8
13
14
15
16
17
18
19
20
21
22
23
24
Z9+ Z9- Z10+ Z10-
25
26
27
28
Regulated
12 VDC
Normal/Silence Switch
DMP Model 866
45mA @ 12 VDC
The 866 Notification
Appliance Circuit
Module in alarm draws
up to 31mA through
its Terminal 3 Alarm
Input and 45mA from
its Terminal 1 Aux
Power Input.
The maximum
voltage drop
between the panel
Bell Output and the
Model 308 EOL is 1
VDC when a
separate power
supply is not used.
1
2
3
4
5
6
7
8
Model 310
1K EOL
AUX PWR
GND
Alarm In
Bell PWR In
Bell Out +
Bell Out Bell Trouble
Bell Trouble
Note: Terminals 3 and 4 jumper together
to supply Bell Power from the panel
Only one notification appliance may be used when
not using a sync module.
The Bell Output programming for Fire type
zones must be set to Temporal.
Model 308
10K EOL
XR500 Series Installation Guide
Listed, Polarized
Notification Appliance
See the Notification Appliance section
for a list of appliances.
Digital Monitoring Products
39
Wiring Diagrams
37.3 866 Class B Style W Multiple Notification Appliance Circuit
J4
J1
P3
J6 Interface
Card
Expansion
Connector
J4
Tamper
J3
Phone Line
PANEL
MAIN
F2
XR500 Series Command
Processor™ Panel
BACKUP
F1
J2
J5
K1
J1
Ethernet
K2
J21
Power LED
J23
R
L
X
RS-232
J22
LX-Bus
P10
J10
J2
Battery
Start
Out2
–
+
Output 2
Output 1
DS1
Buzzer
K6
J11
K7
3
4
5
6
J8
PROG
AC
AC
+B
-B
1
2
3
4
BELL GND RED YEL
5
6
7
8
GRN BLK
9
SMK GND
10
11
12
Z1
GND
Z2
Z3
GND
Z4
Z5
GND
Z6
Z7
GND
Z8
Z9+ Z9- Z10+ Z10-
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Regulated
12 VDC
DMP Model 866
45mA @ 12 VDC
The Model 866
Notification Appliance
Circuit Module in
alarm draws up to
31mA through
Terminal 3 Alarm
Input and 45mA from
Terminal 1 Aux Power
Input.
Normal/Silence Switch
1
2
3
4
5
6
7
8
Model 310
1K EOL
AUX PWR
GND
Alarm In
Bell PWR In
Bell Out +
Bell Out Bell Trouble
Bell Trouble
SM-12/24 Module
Auxiliary Power Supply must be regulated, power
limited, and listed for Fire Protective Signaling
Service. Power Supplies must have battery backup.
Note: If an auxiliary power supply is not used,
terminals 3 and 4 can be jumpered together to
supply Bell Power from the panel.
When using a separate power supply, the
maximum current is 3 Amps.
J6
505-12 Power
Supply
The Bell Output
programming for Fire
type zones must be set
to Steady.
Green
LED
J2
AC
AC
Red
LED
DC
J3
12 VDC @ 5 Amps
+ DC -
Battery AC
Start Trouble
Batt
Trouble
J4
+ BAT -
The Auxiliary Power Supply and Notification Circuit
Module trouble contact zone must be programmed
as a Supervisory Type zone and must be selected
for display in the keypad status list.
Sync module required when
using multiple notification
appliances
Model 308
10K EOL
Polarized Notification
Appliances
The maximum voltage drop
between the panel Bell Output and
the Model 308 is 1 VDC when a
separate power supply is not used.
See the Notification Appliance
section for a list of appliances.
Digital Monitoring Products
40
XR500 Series Installation Guide
Wiring Diagrams
37.4 866 Class B Style W Dual Notification Appliance Circuits
MAIN
J4
J1
P3
J6 Interface
Card
Expansion
Connector
J4
Tamper
J3
Phone Line
PANEL
F2
BACKUP
F1
J2
J5
XR500 Series Command
Processor™ Panel
K1
J1
Ethernet
K2
J21
J23
R
L
X
RS-232
J22
LX-Bus
P10
–
+
Output 2
Output 1
DS1
Buzzer
J10
J2
Battery
Start
K6
Out2
Power LED
J11
K7
3
4
5
6
J8
PROG
AC
AC
+B
-B
1
2
3
4
BELL GND RED YEL
5
6
7
8
GRN BLK
9
10
SMK GND
11
12
Z1
GND
Z2
Z3
GND
Z4
Z5
GND
Z6
Z7
GND
Z8
13
14
15
16
17
18
19
20
21
22
23
24
The Model 866
Notification Appliance
Circuit Module in
alarm draws up to
31mA through its
Terminal 3 Alarm
Input and 45mA from
its Terminal 1 Aux
Power Input.
Normal/Silence Switch
1
2
3
4
5
6
7
8
Model 310
1K EOL
AUX PWR
GND
Alarm In
Bell PWR In
Bell Out +
Bell Out Bell Trouble
Bell Trouble
DSM-12/24 Module
Sync module required when
using multiple notification
appliances
+IN 1
MINUS 1
+AUD
-AUD
+OUT 2
+IN 2
MINUS 2
26
27
28
When using a separate power supply, the
maximum current is 3 Amps.
Note: If an auxiliary power supply is not used, terminals
3 and 4 can be jumpered together to supply Bell Power
from the panel.
J6
505-12 Power
Supply
The Bell Output
programming for Fire
type zones must be set
to Steady.
+OUT 1
25
Auxiliary Power Supply must be regulated, power
limited, and listed for Fire Protective Signaling
Service. Power Supplies must have battery backup.
Regulated
12 VDC
DMP Model 866
45mA @ 12 VDC
Z9+ Z9- Z10+ Z10-
Green
LED
J2
AC
AC
Red
LED
DC
J3
Battery AC
Start Trouble
12 VDC @ 5 Amps
+ DC -
Batt
Trouble
J4
+ BAT -
The Auxiliary Power Supply and Notification
Circuit Module trouble contact zone must be
programmed as a Supervisory Type zone and
must be selected for display in the keypad
status list.
Model 308
10K EOL
The maximum voltage drop
between the panel Bell Output and
the Model 308 is 1 VDC when a
separate power supply is not used.
Model 308
10K EOL
Listed, Polarized Notification Appliances
See the Notification Appliance section for a list of appliances.
XR500 Series Installation Guide
Digital Monitoring Products
41
Wiring Diagrams
37.5 865 Class B Style W using Single Notification Appliance
J1
P3
PANEL
MAIN
F2
J4
J6 Interface
Card
Expansion
Connector
J4
Tamper
J3
Phone Line
XR500 Series Command
Processor™ Panel
BACKUP
F1
J2
J5
K1
J1
Ethernet
K2
J21
J23
R
L
X
RS-232
J22
LX-Bus
P10
–
+
Output 2
Output 1
DS1
Buzzer
J10
J2
Battery
Start
K6
Out2
Power LED
J11
K7
3
4
5
6
J8
PROG
AC
AC
+B
-B
1
2
3
4
BELL GND RED YEL
5
6
7
8
GRN BLK
9
SMK GND
10
The Model 865
Notification Appliance
Circuit Module in
alarm draws up to
59mA through its
Terminal 3 Alarm
Input and 26mA from
the Terminal 1
Aux Power Input.
Normal
S1
J2
CR6
CR5
Bell
Silence
TRBL
GND
FAULT
J1
12
GND
Z2
Z3
GND
Z4
Z5
GND
Z6
Z7
GND
Z8
13
14
15
16
17
18
19
20
21
22
23
24
Z9+ Z9- Z10+ Z10-
25
26
27
28
The Bell Output programming for Fire
type zones must be set to Temporal.
Regulated
12 VDC
DMP Model 865
26mA @ 12 VDC
11
Z1
Model 310
1K EOL
AUX PWR 1
GND 2
Alarm In 3
Bell PWR In + 4
Note: Terminals 3 and 4 jumper together to
supply Bell Power from the panel.
Bell PWR In - 5
Bell Out A + 6
Bell Out A - 7
Bell Out B + 8
Bell Out B - 9
Bell Trouble 10
Bell Trouble 11
Model 308
10K EOL
The maximum voltage drop
between the panel Bell Output and
the Model 308 is 1 VDC when a
separate power supply is not used.
Digital Monitoring Products
42
Listed Polarized Notification
Appliance
See the Notification Appliance
section for a list of appliances.
XR500 Series Installation Guide
Wiring Diagrams
37.6 865 Class B Style W Multiple Notification Appliance Circuit
J1
P3
PANEL
MAIN
F2
J4
J6 Interface
Card
Expansion
Connector
J4
Tamper
J3
Phone Line
BACKUP
F1
J2
J5
XR500 Series Command
Processor™ Panel
K1
J1
Ethernet
K2
J21
J23
RS-232
L
X
J22
LX-Bus
P10
–
+
Output 2
Output 1
DS1
Buzzer
J10
J2
Battery
Start
K6
Out2
Power LED R
J11
K7
3
4
5
6
J8
PROG
AC
AC
+B
-B
1
2
3
4
BELL GND RED YEL
5
6
7
8
GRN BLK
9
10
SMK GND
11
12
Z1
GND
Z2
Z3
GND
Z4
Z5
GND
Z6
Z7
GND
Z8
13
14
15
16
17
18
19
20
21
22
23
24
Regulated
12 VDC
DMP Model 865
26mA @ 12 VDC
CR6
CR5
The Model 865
Notification Appliance
Circuit Module in
alarm draws up to
59mA through its
Terminal 3 Alarm
Input and 26mA from
the Terminal 1
Aux Power Input.
Bell
Silence
TRBL
GND
FAULT
J1
Model 310
1K EOL
26
27
28
Auxiliary Power Supply must be regulated, power
limited, and listed for Fire Protective Signaling
Service. Power Supplies must have battery backup.
Note: If an auxiliary power supply is not used,
terminals 3 and 4 can be jumpered together to
supply Bell Power from the panel.
AUX PWR 1
GND 2
Alarm In 3
Bell PWR In + 4
Bell PWR In - 5
Bell Out A + 6
Bell Out A - 7
J6
505-12 Power
Supply
Bell Out B + 8
Bell Out B - 9
12 VDC @ 5 Amps
+ DC -
Bell Trouble 10
Bell Trouble 11
SM-12/24 Module
Sync module required when
using multiple notification
appliances
25
When using a separate power supply, the
maximum current is 3 Amps.
Normal
S1
J2
Z9+ Z9- Z10+ Z10-
The Bell Output
programming for Fire
type zones must be set
to Steady.
Green
LED
J2
AC
AC
Red
LED
DC
J3
Battery AC
Start Trouble
Batt
Trouble
J4
+ BAT -
The Auxiliary Power Supply and Notification
Circuit Module trouble contact zone must be
programmed as a Supervisory Type zone and
must be selected for display in the keypad
status list.
Model 308
10K EOL
Polarized Notification Appliances
See the Notification Appliance section for a list of appliances.
XR500 Series Installation Guide
The maximum voltage drop
between the panel Bell Output and
the Model 308 is 1 VDC when a
separate power supply is not used.
Digital Monitoring Products
43
Wiring Diagrams
37.7 865 Class B Style W Dual Notification Appliance Circuits
J1
P3
PANEL
MAIN
F2
J4
J6 Interface
Card
Expansion
Connector
J4
Tamper
J3
Phone Line
BACKUP
F1
J2
J5
XR500 Series Command
Processor™ Panel
K1
J1
Ethernet
K2
J21
J23
RS-232
L
X
J22
LX-Bus
P10
–
+
Output 2
Output 1
DS1
Buzzer
J10
J2
Battery
Start
K6
Out2
Power LED R
J11
K7
3
4
5
6
J8
PROG
AC
AC
+B
-B
1
2
3
4
BELL GND RED YEL
5
6
7
8
GRN BLK
9
10
SMK GND
11
12
Z1
GND
Z2
Z3
GND
Z4
Z5
GND
Z6
Z7
GND
Z8
13
14
15
16
17
18
19
20
21
22
23
24
Z9+ Z9- Z10+ Z10-
25
26
27
28
Regulated
12 VDC
DMP Model 865
26mA @ 12 VDC
Normal
S1
Bell
Silence
TRBL
GND
FAULT
J1
J2
CR6
CR5
The Model 865
Notification Appliance
Circuit Module in
alarm draws up to
59mA through its
Terminal 3 Alarm
Input and 26mA from
the Terminal 1
Aux Power Input.
Model 310
1K EOL
Auxiliary Power Supply must be regulated, power
limited, and listed for Fire Protective Signaling
Service. Power Supplies must have battery backup.
Note: If an auxiliary power supply is not used,
terminals 3 and 4 can be jumpered together to
supply Bell Power from the panel.
AUX PWR 1
GND 2
Alarm In 3
Bell PWR In + 4
Bell PWR In - 5
Bell Out A + 6
Bell Out A - 7
J6
505-12 Power
Supply
Bell Out B + 8
Bell Out B - 9
12 VDC @ 5 Amps
+ DC -
Bell Trouble 10
Bell Trouble 11
DSM-12/24 Module
Sync module required when
using multiple notification
appliances
+OUT 1
+IN 1
MINUS 1
+AUD
-AUD
+OUT 2
+IN 2
MINUS 2
When using a separate
power supply, the
maximum current is 3
Amps.
The Bell Output
programming for Fire
type zones must be set
to Steady.
Green
LED
J2
AC
AC
Red
LED
DC
J3
Battery AC
Start Trouble
Batt
Trouble
J4
+ BAT -
The Auxiliary Power Supply and Notification
Circuit Module trouble contact zone must be
programmed as a Supervisory Type zone and
must be selected for display in the keypad
status list.
Model 308
10K EOL
The maximum voltage drop
between the panel Bell Output and
the Model 308 is 1 VDC when a
separate power supply is not used.
Model 308
10K EOL
Polarized Notification Appliances
See the Notification Appliance section for a list of appliances.
Digital Monitoring Products
44
XR500 Series Installation Guide
Wiring Diagrams
37.8 865 Class A Style X using Single Notification Appliance
J1
P3
PANEL
MAIN
F2
J4
J6 Interface
Card
Expansion
Connector
J4
Tamper
J3
Phone Line
XR500 Series Command
Processor™ Panel
BACKUP
F1
J2
J5
K1
J1
Ethernet
K2
J21
J23
RS-232
L
X
J22
LX-Bus
P10
–
+
Output 2
Output 1
DS1
Buzzer
J10
J2
Battery
Start
K6
Out2
Power LED R
J11
K7
3
4
5
6
J8
PROG
AC
AC
+B
-B
1
2
3
4
BELL GND RED YEL
5
6
7
8
GRN BLK
9
SMK GND
10
11
12
Z1
GND
Z2
Z3
GND
Z4
Z5
GND
Z6
Z7
GND
Z8
13
14
15
16
17
18
19
20
21
22
23
24
Z9+ Z9- Z10+ Z10-
25
26
27
28
Regulated
12 VDC
Normal
S1
J2
DMP Model 865
26mA @ 12 VDC
CR6
CR5
Bell
Silence
TRBL
GND
FAULT
J1
Model 310
1K EOL
AUX PWR 1
The 865 Notification
Appliance Circuit
Module in alarm draws
up to 59mA through
its Terminal 3 Alarm
Input and 26mA from
the Terminal 1
Aux Power Input.
GND 2
Note: Terminals 3 and 4 jumper together
to supply Bell Power from the panel
Alarm In 3
Bell PWR In + 4
Bell PWR In - 5
Terminals 2 and 5 jumper together to
provide Ground from the panel
Bell Out A + 6
Bell Out A - 7
Bell Out B + 8
Bell Out B - 9
Only one notification appliance may be used
when not using a sync module.
Bell Trouble 10
Bell Trouble 11
The Bell Output programming for Fire type
zones must be set to Temporal.
Listed, Polarized
Notification Appliance
See the Notification Appliance section
for a list of appliances.
XR500 Series Installation Guide
Digital Monitoring Products
45
Wiring Diagrams
37.9 867 Class B Style W using Single Notification Appliance
J1
P3
J4
Tamper
J3
Phone Line
PANEL
MAIN
F2
J4
J6 Interface
Card
Expansion
Connector
XR500 Series Command
Processor™ Panel
BACKUP
F1
J2
J5
K1
J1
Ethernet
K2
J21
Power LED
J23
R
L
X
RS-232
J22
LX-Bus
–
+
Output 2
Output 1
DS1
Buzzer
J10
J2
Battery
Start
K6
Out2
P10
J11
K7
3
4
5
6
J8
PROG
AC
AC
+B
-B
1
2
3
4
BELL GND RED YEL
5
6
7
8
GRN BLK
9
10
SMK GND
11
12
Z1
GND
Z2
Z3
GND
Z4
Z5
GND
Z6
Z7
GND
Z8
13
14
15
16
17
18
19
20
21
22
23
24
Z9+ Z9- Z10+ Z10-
25
26
27
28
Normal/Silence Switch
DMP Model 867
30mA @ 12 VDC
Ground Fault LED
Bell Trouble LED
Bell In + 1
The 867 must have its
own independent
address ranging from
500 to 999. A
Supervisory zone must
be programmed into the
XR500 Series to properly
supervise each module.
Bell Relay
Address
Supervisory
Address
Model 310
1K EOL
Auxiliary Power Supply must be Listed for Fire
Protective Signaling Service. Power Supplies
must have battery backup.
Bell In - 2
Bell Out + 3
Bell Out - 4
Bell Trouble 5
Bell Trouble 6
PWR Mon. 7
Mon. RTN 8
TENS
ONES
Bell Ring Style (Temporal)
TENS
ONES
Power Supply Monitor LED
Data LED
505-12 Power
Supply
Green
LED
J2
AC
LX-Bus Wiring
AC
Model 308
10K EOL
Listed, Polarized
Notification Appliances
Red
LED
DC
J3
Battery AC
Start Trouble
J6
12 VDC @ 5 Amps
+ DC -
Batt
Trouble
J4
+ BAT -
The Auxiliary Power Supply and Notification
Circuit Module trouble contact zone must be
programmed as a Supervisory Type zone and
must be selected for display in the keypad
status list.
See the Notification Appliance section
for a list of appliances.
Only one notification appliance may be
used when not using a sync module.
Digital Monitoring Products
46
XR500 Series Installation Guide
Wiring Diagrams
37.10 867 Class B Style W Multiple Notification Appliance Circuit
J1
P3
PANEL
MAIN
F2
J4
J6 Interface
Card
Expansion
Connector
J4
Tamper
J3
Phone Line
XR500 Series Command
Processor™ Panel
BACKUP
F1
J2
J5
K1
J1
Ethernet
K2
J21
Power LED
J23
R
L
X
RS-232
J22
LX-Bus
–
+
Output 2
Output 1
DS1
Buzzer
J10
J2
Battery
Start
K6
Out2
P10
J11
K7
3
4
5
6
J8
PROG
AC
AC
+B
-B
1
2
3
4
BELL GND RED YEL
5
6
7
8
GRN BLK
9
10
SMK GND
11
12
Z1
GND
Z2
Z3
GND
Z4
Z5
GND
Z6
Z7
GND
Z8
13
14
15
16
17
18
19
20
21
22
23
24
Z9+ Z9- Z10+ Z10-
25
26
27
28
Normal/Silence Switch
DMP Model 867
30mA @ 12 VDC
Ground Fault LED
Bell Trouble LED
The 867 must have its
own independent
address ranging from
500 to 999. A
Supervisory zone must
be programmed into the
panel to properly
supervise each module.
Model 310
1K EOL
Bell In + 1
Auxiliary Power Supply must be Listed for Fire
Protective Signaling Service. Power Supplies
must have battery backup.
Bell In - 2
When using an SM Sync Module, the
maximum current is 3 Amps.
Bell Out + 3
Bell Out - 4
Bell Trouble 5
Bell Trouble 6
PWR Mon. 7
Mon. RTN 8
Bell Relay
Address
Supervisory
Address
TENS
ONES
Bell Ring Style (Steady)
TENS
ONES
Power Supply Monitor LED
Data LED
LX-Bus Wiring
SM-12/24 Module
J6
505-12 Power
Supply
Green
LED
J2
AC
AC
Red
LED
DC
J3
12 VDC @ 5 Amps
+ DC -
Battery AC
Start Trouble
Batt
Trouble
J4
+ BAT -
The Auxiliary Power Supply and Notification
Circuit Module trouble contact zone must be
programmed as a Supervisory Type zone and
must be selected for display in the keypad
status list.
Sync module required when using multiple notification appliances
Model 308
10K EOL
Listed, Polarized
Notification Appliances
See the Notification Appliance
section for a list of appliances.
XR500 Series Installation Guide
Digital Monitoring Products
47
Wiring Diagrams
37.11 867 Class B Style W Multiple Notification Appliance Circuits
J1
P3
PANEL
MAIN
F2
J4
J6 Interface
Card
Expansion
Connector
J4
Tamper
J3
Phone Line
XR500 Series Command
Processor™ Panel
BACKUP
F1
J2
J5
K1
J1
Ethernet
K2
J21
Power LED
J23
R
L
X
RS-232
J22
LX-Bus
–
+
Output 2
Output 1
DS1
Buzzer
J10
J2
Battery
Start
K6
Out2
P10
J11
K7
3
4
5
6
J8
PROG
AC
AC
+B
-B
1
2
3
4
BELL GND RED YEL
5
6
7
GRN BLK
8
9
10
SMK GND
11
12
Z1
GND
Z2
Z3
GND
Z4
Z5
GND
Z6
Z7
GND
Z8
13
14
15
16
17
18
19
20
21
22
23
24
Z9+ Z9- Z10+ Z10-
25
26
27
28
Normal/Silence Switch
DMP Model 867
30mA @ 12 VDC
Model 310
1K EOL
Ground Fault LED
Bell Trouble LED
The 867 must have its
own independent
address ranging from
500 to 999. A
Supervisory zone must
be programmed into the
panel to properly
supervise each module.
Bell In + 1
Auxiliary Power Supply must be Listed for Fire
Protective Signaling Service. Power Supplies
must have battery backup.
Bell In - 2
When using an DSM Sync Module, the
maximum current is 3 Amps.
Bell Out + 3
Bell Out - 4
Bell Trouble 5
Bell Trouble 6
PWR Mon. 7
Mon. RTN 8
Bell Relay
Address
Supervisory
Address
TENS
ONES
TENS
ONES
Bell Ring Style (Steady)
Power Supply Monitor LED
Data LED
LX-Bus Wiring
DSM-12/24 Module
505-12 Power
Supply
Green
LED
J2
AC
AC
Sync module required when using
multiple notification appliances
+OUT 1
+IN 1
MINUS 1
+AUD
-AUD
+OUT 2
+IN 2
MINUS 2
Red
LED
DC
J3
Battery AC
Start Trouble
J6
12 VDC @ 5 Amps
+ DC -
Batt
Trouble
J4
+ BAT -
The Auxiliary Power Supply and Notification
Circuit Module trouble contact zone must be
programmed as a Supervisory Type zone and
must be selected for display in the keypad
status list.
Model 308
10K EOL
Model 308
10K EOL
Listed, Polarized Notification Appliances
See the Notification Appliance section
for a list of appliances.
Digital Monitoring Products
48
XR500 Series Installation Guide
Wiring Diagrams
37.12 Panel Slave Communicator for FACP using 630F Annunciator
XR500 Series
Command Processor™ Panel
J4
Tamper
J3
Phone Line
J1
Ethernet
J21
Power LED
J23
RS-232
J22
LX-Bus
Output 2
Output 1
J10
Battery
Start
Out2
J2
K6
K7
3
4
5
6
J8
PROG
To 322/323
transformer
Must be connected
to same circuit
as FACP
AC
AC
+B
-B
1
2
3
4
BELL GND RED YEL
5
6
7
GRN BLK
8
9
10
SMK GND
11
12
J11
Z1
GND
Z2
Z3
GND
Z4
Z5
GND
Z6
Z7
GND
Z8
13
14
15
16
17
18
19
20
21
22
23
24
Z9+ Z9- Z10+ Z10-
25
26
27
28
Program Bell Options
fire type as None.
Model 311
1K EOL
Standy
Batteries
Fire Command Center
POWER
TROUBLE
ALARM
SILENCE
RESET
ABC
TEST
MNO
1
DEF
2
GHI
3
JKL
4
ENABLE
YX
DRILL
5
9
PQR
6
0
STU
7
VWX
8
COMMAND
630F Annunciator
Program forFire Protective Signaling communication to the
Central Station.
Program Fire Alarm zone as type FI and set Fire Panel Slave
Input option as YES.
Program General Trouble zone as type FI.
Program Supervisory zone as type SV and set the Latch
Supervisory option in System Options as NO.
Fire Alarm
Form C alarm contacts activate
short on General Fire Alarm.
General Trouble
Form C trouble contacts activate
open on General Trouble.
General Trouble must not be
used to indicate AC power fail
unless it can be delayed at least
1 hour.
Supervisory
Form C contacts activate short on
Supervisory condition.
XR500 Series Installation Guide
Main Fire Alarm
Control Panel (FACP)
{
{
{
Normally Open
Common
Normally Closed
Normally Open
Common
Normally Closed
Normally Open
Common
Normally Closed
Zone 3
1.0k Ohm
Zone 4
1k Ohm EOL
1.0k Ohm
Zone 6
Digital Monitoring Products
49
Wiring Diagrams
37.13 Panel Slave Communicator for FACP using Outputs
J4
Tamper
J3
Phone Line
XR500 Series
Command Processor™ Panel
Communication Fail
Output 1 must be programmed
as a Comm Fail output in Output
Options.
J1
Ethernet
J21
Power LED
J23
RS-232
J22
LX-Bus
Output 2
Out2
Output 1
J10
J2
Battery
Start
K6
To 322/323
transformer
Must be connected
to same circuit
as FACP
AC
+B
-B
1
2
3
4
BELL GND RED YEL
5
6
Model 311
1K EOL
7
GRN BLK
8
9
10
FACP EOL
K7
Out1
J8
PROG
AC
SMK GND
11
12
Fire Trouble
Output 2 must be programmed
as a Fire Trouble output in
Output Options.
FACP EOL
Z1
GND
Z2
Z3
GND
Z4
Z5
GND
Z6
Z7
GND
Z8
13
14
15
16
17
18
19
20
21
22
23
24
Z9+ Z9- Z10+ Z10-
25
26
27
28
Program Bell Options
fire type as None.
Standy
Batteries
Program for Fire Protective Signaling communication to the
Central Station.
Program FireAlarm zone as type FI and set Fire Panel Slave Input
option as YES.
Program General Trouble zone as type FI.
Program Supervisory zone as type SV and set the Latch
Supervisory option in System Options as NO.
Fire Alarm
Form C alarm contacts activate
short on General Fire Alarm.
General Trouble
Form C trouble contacts activate
open on General Trouble.
General Trouble must not be
used to indicate AC power fail
unless it can be delayed at least
1 hour.
Supervisory
Form C contacts activate short on
Supervisory condition.
Communication Fail
Program FACP Zone Input to
indicate a communication trouble
locally.
Fire Trouble
Program FACP Zone Input to
indicate a trouble locally.
Digital Monitoring Products
50
Main Fire Alarm
Control Panel (FACP)
{
{
{
Normally Open
Common
Normally Closed
Normally Open
Common
Normally Closed
Normally Open
Common
Normally Closed
Normally Open
Common
Normally Closed
{
{
Zone 3
1.0k Ohm
Zone 4
1k Ohm EOL
1.0k Ohm
Zone 6
FACP Zone Input
Slave Communication Trouble
FACP Zone Input
Slave General Fire Trouble
XR500 Series Installation Guide
Wiring Diagrams
37.14 Dual Style D Zone Module Installation
J4
Tamper
J3
J6
Interface
Card
Expansion
Connector
XR500 Series
Command Processor™
Panel
J1
J21
J23
RS-232
R
L
X
J22
J2
J10
Battery
Start
K6
K7
J11
J16
Reset
J8
AC AC +B –B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
Dual Style D Initiating Module
DMP Model 869
25mA Standby, 75mA Alarm
@ 12 VDC
Model 869
GND
Fault A
A1
A1
A2
A2
Zone A
GND
Aux Power
Zone B
B1
B1
Zone B
B2
B2
Zone A
1
2
3
4
S
Regulated
12 VDC
5
6
7
S
8
9
10
11
12 13
S
14
Z3 GND Z4 Z5 GND Z6
15 16
17 18
19
20
21
Z7 GND Z8 Z9+ Z9– Z10+ Z10–
22
23
24
25
26
27
28
S
S = Supervised Circuit
S
S
S
S
S
S
S
Heat Detectors, manual pull stations, or any other
listed shorting device. Unlimited number of units.
S
GND
Fault B
XR500 Series Installation Guide
Digital Monitoring Products
51
Wiring Diagrams
37.15 Derived Channel Installation Using Bosch D8122
XR500 Series Command Processor™ Panel
J4
Tamper
J3
Phone Line
Form C Dry Contact Relays (J2)
Output Color Code–Model 431 Harness
Output 2 N/O Orange/White
Output 2 Com White/Gray
Output 2 N/C Violet/White
Output 1 N/O Orange
Output 1 Com Gray
Output 1 N/C Violet
J1
J21
Output Header J2 for K6 and K7 Dry Contact
Relays. All outputs must be connected to devices
located within the same room as the panel.
J23
R
L
X
J22
J10
Battery
Start
J2
J11
J16
Reset
J8
PROG
Telco Jack
K6
K7
AC AC +B –B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
1
2
3
4
5
6
7
8
9
J6
Interface
Card
Expansion
Connector
10
11
12 13
14
Z3 GND Z4 Z5 GND Z6
15 16
17 18
19
20
Z7 GND Z8 Z9+ Z9– Z10+Z10–
21 22
23
24
25
26
27
28
P1
P2
J2
J1
+ 12V
+12 VDC Out
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
CONT OUT
COMM
Output 2 Common Wire
Output 1 Common Wire
Panel Common Wire
JP3
JP1
JP2
123 123 123 123
JP4
D8122
Panel Terminal 7 Wire
OPEN
SW1 (MSB)
12345678
OPEN
SW2 (LSB)
12345678
Interfacing D8122 to the XR500 Series Panels
The D8122 may only be used in conjunction with telephone systems that support Derived Channel network. For
installation instructions, see the Derived Channel STUD8121A/D8122 Operation and Installation Guide.
• For Standard Line Security applications, the panel must be installed and programmed to meet burglary alarm
system requirements.
• The panel must be installed and programmed for reporting all alarm conditions through the integral DACT or
network connection to the same central station that monitors the D8122.
• The D8122 must be installed in the same enclosure as the XR500 Series panel using the supplied mounting
hardware. Refer to the STUD8121A/D8122 Operation and Installation Guide.
• Derived Channel Communication is not applicable for ULC Canadian Installations.
Digital Monitoring Products
52
XR500 Series Installation Guide
XR500 Series Installation Guide
Green LED
Red LED
Silence
BLO
BLI
Test
Common
+ 12 VDC
Rothenbuhler 5110
High Security Bell
K3
R
L
X
J23
J10
J22
RS-232
J21
J1
J4
Tamper
K6
J2
1
3
4
Output 1 N/C
Output 2 N/C
2
5
6
S
7
9
S
10
12 13
14
15 16
Output 1 Common
11
10K EOL
DMP Model 308
Output 2 Common
8
J11
18 19
10K EOL
DMP Model
308
17
20
J16
Reset
24
25
26
27
28
S = Supervised Circuit
23
Model 431 Output
Harness
21 22
Z3 GND Z4 Z5 GND Z6
K7
J6
Interface
Card
Expansion
Connector
Z7 GND Z8 Z9+ Z9– Z10+Z10–
XR500 Series
Command Processor™
Panel
J2 Output Header
All outputs must be located
within the same room as
the control panel.
AC AC +B –B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
Battery
Start
J3
Wiring Diagrams
37.16 Rothenbuhler 5110 High Security Bell Wiring
Digital Monitoring Products
53
Wiring Diagrams
37.17 LX-Bus™ Module Connection
LX-Bus Expansion
Interface Card
DMP Models 481, 462N,
462P, 463G, or 472
Each LX-Bus Module must
have its own independent
address ranging from 00 to
99. A Supervisory zone must
be programmed into the
XR500 Series to properly
supervise each module.
S
S
S
S
Red
Yellow
To additional LX-Bus Modules
Green
Black
S
S
S
S
S
LX-Bus™ Wiring
= Supervised Circuit
Optional LED wiring 50mA at
50 VDC resistive
Relay 3
S
Relay 2
S
S
Relay 1
Open Collector
Annunciator Outputs
S
Relay 4
Form C Contacts
Typical
Normally Closed
Common
Normally Open
Model 716 Output
Expander Module
13m at 12 VDC
Optional LED wiring 50mA at
50 VDC resistive
Model 717 Graphic
Annunciator
Module
10m at 12 VDC
Digital Monitoring Products
54
XR500 Series Installation Guide
Wiring Diagrams
37.18 Model 860 Relay Module Connection
XR500 Series
Command Processor™
Panel
J4
Tamper
J3
J2 Output Header
All outputs must be located
within the same room as
the control panel.
J1
J21
J23
RS-232
R
L
X
K6
4
5
6
7
8
9
1
2
3
4
10
11
12 13
J11
K7
AC AC +B –B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
3
Model 860
Relay Module
J2
J10
2
RED
YEL
GRN
BL K
J22
Battery
Start
1
J6
Interface
Card
Expansion
Connector
14
4-wire J2
Harness
Assembly
J16
Reset
Z3 GND Z4 Z5 GND Z6
15 16
17
18 19
20
Z7 GND Z8 Z9+ Z9– Z10+Z10–
21 22
23
24
25
26
27
28
{
Relay 2 {
Relay 3 {
Relay 4 {
Relay 1
N/C
Common
N/O
+12 VDC
Relay contact rating:
1 Amp @ 30 VDC, resistive
37.19 Powered Burglary Devices
J4
Tamper
J3
J6
Interface
Card
Expansion
Connector
XR500 Series
Command Processor™
Panel
J1
J21
J23
RS-232
R
L
X
J22
J2
J10
Battery
Start
K6
K7
J11
J16
Reset
J8
AC AC +B –B BELL GND RED YEL GRN BLK SMK GND Z1 GND Z2
1
2
3
4
5
6
7
8
9
10
11
12 13
14
Z3 GND Z4 Z5 GND Z6
15 16
17 18
19
20
21
Z7 GND Z8 Z9+ Z9– Z10+ Z10–
22
23
24
25
26
27
28
Zone Expander
Z1+
Z5+
Z9+
Z13+
Z1-
Z5-
Z9-
Z13-
Z2+
Z6+
Z10+
Z14+
Z2-
Z6-
Z10-
Z14-
RED
Z3+
Z7+
Z11+
Z15+
YEL
Z3-
Z7-
Z11-
Z15-
GRN
Z4+
Z8+
Z12+
Z16+
Black
Green
Red
Yellow
KYPD LX
J2
TENS ONES
TXD
Red
Yellow
Green
Black
BLK
J3
J5
Z8-
Z4J7
J10
Z12J12
Zone
Connection
Z16J14
PIR or
Glassbreak
+ –
1k
EOL
12 VDC
+ –
505-12 Power
Supply
7060 Keypad
XR500 Series Installation Guide
Digital Monitoring Products
55
Revisions
Revisions to This Document
This section explains the changes that were made to this document during this revision. This section lists the
version, section number with heading, and a quick summary of the change.
Version Section Number and Heading
Summary of Changes
1.09
31.8 Fire Protective Signaling SystemsUpdated to reflect Cell/Net Primary Fire options
1.08
31.8 Fire Protective Signaling SystemsUpdated to reflect 463G Commercial Fire
37.12 Wiring Diagram
Added Panel Slave Communicator using 630F Annunciator
37.13 Wiring Diagram
Added Panel Slave Communicator using Outputs
1.07
18.1 J3 Telephone RJ Connector
Added Caution statement
1.06
3.4 Accessory Devices
Added 1165, 1165H, 1165HS Wireless Smoke Detectors, 1181 PIV, and 1182 OS&Y
6.8 Power Requirements
Updated 1100X Current Draw
31.14 Wireless Testing
Added section for Wireless Commercial Fire requirement
Listings and Approvals
Added UL 268, and UL 346 listings
1.05
3.4 Accessory Devices
Added CellCom Series
24.10 463G or CellCom, CELL Only
Added CellCom reference
24.11 463G or CellCom, NET w/ CELL Added CellCom reference
24.12 463G or CellCom, NET w/ CELL Added CellCom reference
27.9 463G or CellCom, CELL Only
Added CellCom reference
27.10 463G or CellCom, NET w/ CELL Added CellCom reference
27.11 463G or CellCom, NET w/ CELL Added CellCom reference
Digital Monitoring Products
56
XR500 Series Installation Guide
800-641-4282
INTRUSION • FIRE • ACCESS • NETWORKS
www.dmp.com
2500 North Partnership Boulevard
Made in the USA
Springfield, Missouri 65803-8877
10215
FCC Part 15
FCC Part 68 Registration ID CCKAL00BXR500
NIST Validated XR500E Encrypted Command
Processor Panel Certificate #130
California State Fire Marshal (CSFM)
New York City (MEA)
ANSI/SIA CP-01-2000 False Alarm Reduction
Underwriters Laboratories (UL) Listed
Commercial and Residential Fire, Burglar,
Holdup, and Access Protected Premise Unit
ANSI/UL 294 Access Control System Units
ANSI/UL 365 Police Connected Burglar
ANSI/UL 609 Local Burglar
ANSI/UL 636 Holdup Alarm Units and
Systems Accessory
ANSI/UL 1023 Household Burglar
ANSI/UL 1076 Proprietary Burglar
ANSI/UL 1610 Central Station Burglar
ANSI/UL 1635 Digital Burglar
ANSI/UL 268 Smoke-Automatic Fire Detectors
ANSI/UL 346 Waterflow Indicators for Fire Protective Signaling Systems
ANSI/UL 864 Fire Protective Signaling
9th Edition
ANSI/UL 985 Household Fire Warning
UL Bank, Safe, and Vault
UL Standard Line Security
UL Encrypted Standard Line Security
Underwriters Laboratories Canada (ULC) Listed
ULC 5545 Household Fire
ULC Subject-C1023 Household Burglar
ULC/ORD-C1076
Proprietary Burglar
ULC S304Central Station Burglar
LT-0681 1.09 © 2010 Digital Monitoring Products, Inc.
Listings and Approvals
Download PDF