DRS 900 G
D E ’LON GHI
COOKING
USER & INSTALLATION INSTRUCTIONS
DRS 900- G
GAS COOKER
GB
CONTENTS
Page Number
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Safety Precautions & Recommendations . . . . . . . . . . . . . . . . . . . . 4 - 6
Cooking Hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Use of the Hob Burners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 10
Gas Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 15
Oven Temperature Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
120 Minute Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cleaning & Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 - 23
Advice for the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 - 29
Gas Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 - 39
Electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 - 41
Guarantee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
2
Dear Customer,
Thank you for purchasing the DeLonghi DRS 900-G gas
cooker.
The safety precautions and recommendations listed
below are for your own safety and that of others. They
will also provide a means by which to make full use of the
features offered by your appliance.
Please retain this booklet for future reference.
This appliance must be used only for the task it
has explicitly been designed for, that is for cooking
foodstuffs. Any other form of usage is to be considered
as inappropriate and therefore potentially dangerous.
The manufacturer declines all responsibility in the
event of damage caused by improper, incorrect or
illogical use of the appliance.
DECLARATION OF
CE CONFORMITY
This cooker has been designed, constructed, and marketed in compliance with:
•
•
•
•
•
Safety requirements of the “Gas” Directive 2009/142/EC;
Safety requirements of the “Low voltage” Directive 2006/95/EC;
Safety requirements of the “EMC” Directive 2004/108/EC;
Requirements of EU Directive 93/68/EEC;
Requirements of EU Directive 2011/65/EU.
GB
3
IMPORTANT SAFETY PRECAUTIONS AND RECOMMENDATIONS
IMPORTANT: This appliance is designed and manufactured
solely for the cooking of domestic (household) food and is
not suitable for any non domestic application and therefore
should not be used in a commercial environment.
The appliance guarantee will be void if the appliance is used
within a non domestic environment i.e. a semi commercial,
commercial or communal environment.
Read the instructions carefully before installing and using
the appliance.
• After having unpacked the appliance, check to ensure that it is not
damaged and that the oven door closes correctly.
In case of doubt, do not use it and consult your supplier or a
professionally qualified technician.
• Packing elements (i.e. plastic bags, polystyrene foam, nails, packing
straps, etc.) should not be left around within easy reach of children,
as these may cause serious injuries.
• Some appliances are supplied with a protective film on steel and
aluminium parts. This film must be removed before using the
appliance.
• IMPORTANT: The use of suitable protective clothing/gloves is
recommended when handling or cleaning of this appliance.
• Do not attempt to modify the technical characteristics of the appliance
as this may become dangerous to use. The manufacturer declines all
responsability for any inconvenience resulting from the inobservance
of this condition.
• CAUTION: this appIiance must only be installed in a permanently
ventilated room in compliance with the applicable regulations.
• Do not carry out cleaning or maintenance operations on the appliance
without having previously disconnected it from the electric power
supply.
• WARNING: Ensure that the appliance is switched off before replacing
the oven lamp to avoid the possibility of electric shock.
• Do not use a steam cleaner because the moisture can get into the
appliance thus make it unsafe.
4
• Do not touch the appliance with wet or damp hands (or feet).
• Do not use the appliance whilst in bare feet.
• If you should decide not to use this appliance any longer (or decide to
substitute another model), before disposing of it, it is recommended
that it be made inoperative in an appropriate manner in accordance to
health and environmental protection regulations, ensuring in particular
that all potentially hazardous parts be made harmless, especially in
relation to children who could play with unused appliances.
• The various components of the appliance are recyclable. Dispose of
them in accordance with the regulations in force in your country. If the
appliance is to be scrapped, remove the power cord.
• After use, ensure that the knobs are in the off position.
• Children less than 8 years of age shall be kept away unless
continuously supervised.
• This appliance can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision
or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by
children without supervision.
• The manufacturer declines all liability for injury to persons or damage
to property caused by incorrect or improper use of the appliance.
• WARNING: During use the appliance and its accessible parts become
hot; they remain hot for some time after use.
–– Care should be taken to avoid touching heating elements (on the
hob and inside the oven).
–– The door is hot, use the handle.
–– To avoid burns and scalds, young children should be kept away.
• Make sure that electrical cables connecting other appliances in the
proximity of the cooker cannot come into contact with the hob or
become entrapped in the oven door.
• WARNING: Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire. NEVER try to extinguish a fire with
water, but switch of the appliance and then cover flame e.g. with a lid
or a fire blanket.
5
• WARNING: Danger of fire: do not store items on the cooking surfaces.
• WARNING: When correctly installed, your product meets all safety
requirements laid down for this type of product category. However
special care should be taken around the rear or the underneath of the
appliance as these areas are not designed or intended to be touched
and may contain sharp or rough edges, that may cause injury.
• FIRST USE OF THE OVEN - it is advised to follow these instructions:
–– Furnish the interior of the oven as described at chapter “CLEANING
AND MAINTENANCE”.
–– Switch on the empty oven on max to eliminate grease from the
heating elements.
–– Disconnect the appliance from the electrical power supply, let the
oven cool down and clean the interior of the oven with a cloth
soaked in water and neutral detergent; then dry carefully.
• CAUTION: Do not use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can scratch the
surface, which may result in shattering of the glass.
• Do not line the oven walls with aluminium foil. Do not place baking
trays or the drip tray on the base of the oven chamber.
• FIRE RISK! Do not store flammable material in the oven or in the
storage compartment.
• Always use oven gloves when removing the shelves and food trays
from the oven whilst hot.
• Do not hang towels, dishcloths or other items on the appliance or its
handle – as this could be a fire hazard.
• Clean the oven regularly and do not allow fat or oils to build up in the
oven base or tray. Remove spillages as soon as they occur.
• Do not stand on the cooker or on the open oven door.
• Always stand back from the appliance when opening the oven door
to allow steam and hot air to escape before removing the food.
• SAFE FOOD HANDLING: Leave food in the oven for as short a time
as possible before and after cooking. This is to avoid contamination
by organisms which may cause food poisoning. Take particular care
during warmer weather.
• WARNING: Taking care NOT to lift the cooker by the door handle.
6
1 - COOKING HOB
Fig. 1.1
2
2
4
3
1
GAS BURNERS
1. Auxiliary burner (A) 1,00 kW
2. Semi-rapid burner (SR) 1,75 kW
3. Rapid burner (R) 3,00 kW
4. Triple-ring burner (TR) 3,50 kW
Notes:
•
The electric ignition is incorporated in the knobs.
•
The appliance has a safety valve system fitted, the flow of gas will be stopped if and
when the flame should accidentally go out.
7
2 - CONTROL PANEL
Fig. 2.1
OVEN LIGHT
GAS OVEN
1
2
3
4
5
6
7
8
7
9
10
6
5
CONTROLS DESCRIPTION
1. Front right burner control knob
2. Rear right burner control knob
3. Central burner control knob
4. Rear left burner control knob
5. Front left burner control knob
6. 120’ alarm knob
7. Gas oven / gas grill control knob
8. Oven light control knob
8
4
3
2
1
8
3 - USE OF THE HOB BURNERS
GAS BURNERS
Gas flow to the burners is adjusted by
turning the knobs (illustrated in fig. 3.1)
which control the safety valves.
Turning the knob, so that the indicator line
points to the symbols printed on the panel,
achieves the following functions:
- symbol
0
0
closed valve
- symbol
maximum
aperture or flow
- symbol
minimum
aperture or flow
√√
The maximum aperture position
permits rapid boiling of liquids, whereas
the minimum aperture position allows
slower warming of food or maintaining
boiling conditions of liquids.
√√
To reduce the gas flow to minimum
rotate the knob further anti-clockwise
to point the indicator towards the small
flame symbol.
√√
Other
intermediate
operating
adjustments can be achieved by
positioning the indicator between the
maximum and minimum aperture
positions, and never between the
maximum aperture and closed
positions.
Caution!
The cooking hob becomes very hot
during operation.
Keep children well out of reach.
Fig. 3.1
Fig. 3.2
N.B. When the cooker is not being
used, set the gas knobs to their closed
positions.
9
LIGHTING THE BURNERS
To ignite the burner, the
instructions are to be followed:
CHOICE OF THE BURNER
following
1. Press in the corresponding knob and
turn counter-clockwise (fig. 3.2) to the
full flame position marked by the
symbol (fig. 3.1); hold the knob in unt il
the flame has been lit.
In the case of a mains failure light the
burner with a match or lighted taper.
On the control panel, near every knob
there is a diagram that indicates which
burner is controlled by that knob.
The suitable burner must be chosen
according to the diameter and the capacity
used.
As an indication, the burners and the pots
must be used in the following way:
DIAMETERS OF PANS WHICH MAY BE
USED ON THE BURNERS
2. Wait for a few seconds after the gas
burner has been lit before letting go of
the knob (valve activation delay).
BURNERS
3. Adjust the gas valve to the desired
position.
Auxiliary
12 cm
14 cm
Semi-rapid
16 cm
24 cm
Rapid
24 cm
26 cm
Triple-ring
26 cm
28 cm
If the burner flame should go out for some
reason, the safety valve will automatically
stop the gas flow.
To re-light the burner, return the knob to
the closed 0 position, wait for at least
1 minute and then repeat the lighting
procedure.
If your local gas supply makes it difficult
to light the burner with the knob set to
maximum, set the knob to minimum and
repeat the operation.
MINIMUM
MAXIMUM
do not use pans with concave or convex
bases
It is important that the diameter of the pot
be suitable to the potentiality of the burner
so as not to compromise the high output
of the burners and therefore energy waste.
A small pot on a large burner does not give
you a boiling point in a shorter amount of
time since the capacity of heat absorption
of a liquid mass depends on the volume
and the surface of the pot.
Deep Fat Frying
For safety purposes when deep fat frying,
do not fill the pan more than one third full
of oil.
DO NOT cover the pan with a lid and DO
NOT leave the pan unattended.
In the unfortunate event of a fire, leave
the pan where it is and turn off the control
knobs.
Place a damp cloth or lid over the pan to
smother the flames. Leave the pan to cool
for at least 30minutes before moving the
pan.
DO NOT USE WATER ON THE FIRE.
10
Fig. 3.3
4 - GAS OVEN
The glass on the oven door reaches
high temperatures during operation.
Keep children away.
Models with glass lid: The cooker lid
must be kept open when the gas oven/
grill is in use.
GENERAL FEATURES
The oven is furnished completely clean; it
is advisable however, upon first use, to turn
the oven on to the maximum temperature
(position 10 ) to eliminate possible traces
of grease from the oven burner.
The same operation should be followed for
grill burner.
The gas oven is provided with two burners:
•
One gas burner (wattage: 6,20 kW),
located at the bottom, providing safety
device and electric ignition.
•
One gas grill (wattage: 4,65 kW),
placed on the top, providing safety
device and electric ignition.
WARNING:
The door is hot, use the handle.
During use the appliance becomes hot.
Care should be taken to avoid touching
heating elements inside the oven.
GAS OVEN
1
2
3
4
5
Fig. 4.1
6
7
8
9
10
THERMOSTAT
The numbers 1 to 10 printed on the control
panel (fig. 4.1) indicate the increasing oven
temperature value (see table 4.2).
The temperature is kept constant on the
regulated value.
To regulate the temperature, make the
indicator of the knob (fig. 4.1) match with
the chosen number on the control panel.
The thermostat which regulates the flow
of gas to the oven burner has a safety
valve which automatically shuts off the gas
supply when the flame goes out.
OVEN BURNER
It carries out normal “oven cooking”.
The gas flow to the burner is regulated by
a thermostat which allow to maintain the
oven temperature constant.
The control of the temperature is assured
by a thermostatic probe positioned inside
the oven.
The probe must be always kept in its
housing, in a clean condition, as an
incorrect position or encrustment may
cause an alteration in the control of the
temperature.
Table 4.2
THERMOSTAT GRADE TABLE
Thermostat
indicator
Oven
temperature
1
150 °C
2
165 °C
3
180 °C
4
195 °C
5
210 °C
6
225 °C
7
240 °C
8
255 °C
9
270 °C
10
285 °C
11
IGNITION OF THE OVEN BURNER
ATTENTION: Never turn the control
knob before opening the oven door.
To ignite the oven burner:
1. Open the oven door to the full extent.
WARNING: Risk of explosion! The
oven door must be open during this
operation.
required.
If the flame extinguishes for any reason,
the safety valve will automatically shut off
the gas supply to the burner.
To re-light the burner, first turn the oven
control knob to position 0, wait for at
least 1 minute and then repeat the lighting
procedure.
2. Lightly press and turn the thermostat
knob anti-clockwise (fig. 4.3) to
(fig. 4.1).
maximum position 10
Press the knob firmly until the burner
lights.
In the case of a mains failure, to light
the oven burner manually, approach
a flame to the hole ‘A’ of the oven
floor (fig. 4.4). Never turn the gas
thermostat before approaching a
flame to the hole “A” of the floor.
3. Never continue this operation for
more than 15 seconds. If the burner
has still not ignited, wait for about
1 minute prior to repeating the
ignition.
Fig. 4.3
4. After lighting the burner, wait a few
seconds before releasing the knob
(until the safety valve stays open).
5. Close the oven door slowly and adjust
the burner according to the power
A
Fig. 4.4
12
For efficient oven preheating, we
recommend that grill tray and racks are
removed from the oven and replaced
after about 15 minutes.
OVEN COOKING
To cook, before introducing the food, preheat
the oven to the desired temperature.
When the oven has reached the desired
temperature, introduce the food, control
the cooking time and turn off the oven
5 minutes before the theoretical time to
recuperate the stored heat.
COOKING EXAMPLES
Temperatures are approximate as they
vary depending on the quality and amount
of food.
Remember to use ovenproof dishes and to
adjust the oven temperature during cooking
if necessary.
DISHES
TEMPERATURE
Las agne
B aked pas ta
P izza
C reole rice
B aked onions
S pinach crêpes
P otatoes baked in milk
S tuffed tomatoes
C hees e s oufflé
R oas t veal
G rilled veal chops
C hicken breas ts with tomato
G rilled chicken - roas t chicken
Veal loaf
R oas t beef
Fillet of s ole
Aromatic hake
B eignets
R ing cake
P lum tart
J am tartlets
S ponge cake
S weet dough
S weet puffs
P lain s ponge cake
190°C
190°C
220°C
190°C
190°C
185°C
185°C
180°C
170°C
180°C
210°C
180°C
190°C
175°C
170°C
175°C
170°C
160°C
150°C
170°C
160°C
170°C
160°C
170°C
170°C
13
IGNITION OF THE GRILL BURNER
ATTENTION: Never turn the control
knob before opening the oven door.
To ignite the grill burner:
1. Open the oven door to the full extent.
WARNING: Risk of explosion! The
oven door must be open during this
operation.
If the flame extinguishes for any reason,
the safety valve will automatically shut off
the gas supply to the burner.
To re-light the burner, first turn the grill
control knob to position 0, wait for at
least 1 minute and then repeat the lighting
procedure.
2. Lightly press and turn the thermostat
knob clockwise to the position
(fig. 4.5). Press the knob firmly until
the burner lights.
In the case of a mains failure, to light
the grill burner manually, approach a
flame to the pipe of the burner (fig.
4.6). Never turn the gas thermostat
before approaching a flame to the
burner.
3. Never continue this operation for
more than 15 seconds. If the burner
has still not ignited, wait for about
1 minute prior to repeating the
ignition.
4. After lighting the burner, wait a few
seconds before releasing the knob
(until the safety valve stays open).
Do not close completely the oven
door. The grill must always be used
with the oven door slightly open
and with shield “A” mounted (Fig.
4.7). See specific instructions in the
section ‘USE OF THE GRILL’.
GAS OVEN
1
2
3
4
5
6
7
8
9
10
Fig. 4.5
Fig. 4.6
14
USE OF THE GRILL
OVEN LIGHT
Very important: The grill must always be
used with the oven door slightly open
and with shield “A” mounted (Fig. 4.7).
The cooker is equipped with a light that
illuminates the oven to enable visually
controlling the food that is cooking.
Mount shield “A” (fig. 4.7) which serves to
protect the control panel from the heat.
Turn on the grill, as explained in the
preceding paragraphs and let the oven
preheat for about 5 minutes with the door
ajar.
Introduce the food to be cooked, positioning
the rack as close to the grill as possible.
The dripping pan should be placed under
the rack to catch the cooking juices and
fats.
This light is controlled by a control knob
(fig. 4.8).
Note: It is recommended that you do not
grill for longer than 30 minutes at any
one time.
Attention: The oven door becomes very
hot during operation.
Keep children away.
WARNING:
Hot part allow to cool
before removing
OVEN DOOR GUARD
The glass on the oven door reaches high
temperatures during operation.
For child safety, a door guard can be fitted
to prevent contact with the hot glass.
The door guard is supplied as an accessory
at extra cost, if required.
Contact the After-Sales Service and
indicate the model name of your product
OVEN LIGHT
Fig. 4.8
Fig. 4.7
A
15
5 - OVEN TEMPERATURE GUIDE
Cooking process
Oven heat
Gas mark
Keeping food hot,
milk puddings
very cool
Electric oven temperature
°C
°F
½
120
250
cool
1
140
275
cool
2
150
300
Low temperature
roasting, shortbread
moderate
3
160
325
Victoria sandwich,
plain fruit cake,
baked fish
moderate
4
180
350
Small cakes, choux
pastry
fairly hot
5
190
375
Short pastry, Swiss
rolls, soufflés
fairly hot
6
200
400
High
temperature
roasting, flaky
pastry, scones
hot
7
220
425
Puff pastry, bread
very hot
8
230
450
Small puff pastries,
browning
cooked
foods
very hot
9
240
475
Egg custards
Rich fruit
braising
cakes,
These temperatures relate to the centre oven temperature.
Remember to use ovenproof dishes and to adjust the oven temperature during cooking if
necessary.
16
6 - 120 MINUTE TIMER
120 MINUTE TIMER (Fig. 6.1)
The timer can be set to a maximum of 120
minutes and a buzzer will sound at the end
of the countdown.
The knob must be rotated clockwise as
far as the 120 minute position first and
then set to the required time by rotating it
anticlockwise.
IMPORTANT WARNING: This is only a
mechanical timer.
Remember to turn off the oven/grill
manually.
Fig. 6.1
17
7 - CLEANING AND MAINTENANCE
GENERAL ADVICE
CLEANING
•
•
Stainless steel hob: Spillage on
the hob can usually be removed by
a damp soapy cloth. More obstinate
stains can be removed by using a
proprietary stainless steel cleaning
product that does not contain chlorine
or acidic base.
•
Control panel facia: Clean very
carefully with water and neutral soap;
the cloth used must be rinsed well and
must be free of any cleaning chemicals
to avoid damaging any screen print on
the facia.
•
Door, glass & painted surfaces:
Clean very carefully with water and
neutral soap; the cloth used must be
rinsed well and must be free of any
cleaning chemicals.
•
Pan stands & burner caps: Clean
with a sponge and soapy water or
proprietary cream cleaner. Alway
dry throughly. DO NOT PUT IN THE
DISHWASHER.
•
Burner bodies (aluminium alloy):
They should be cleaned with soapy
water and a clean cloth. For stubborn
stains a proprietary cream or stainless
steel cleaner may be used; however
to maintain an uniform finish we
would recommend the whole area is
cleaned. NOTE: Please ensure the
slots/castlellations are kept free of the
any material/cleaner.
•
•
•
•
•
•
•
Before you begin cleaning, you
must ensure that the appliance is
switched off at the cooker switch.
The periodical lubrication of the gas
taps must be done only by specialized
personnel.
If a tap becomes stiff, do not force;
contact your local After Sales Service
Centre.
It is advisable to clean when the
appliance is cold and especially when
cleaning the enamelled parts.
Avoid leaving alkaline or acidic
substances (lemon juice, vinegar, etc.)
on the surfaces.
Avoid using cleaning products with
a chlorine or acidic base.
Important: The use of suitable
protective
clothing/gloves
is
recommended when handling or
cleaning this appliance.
Under no circumstances should
any external covers be removed for
servicing or maintenance except by
suitable qualified personnel.
WARNING:
When correctly installed, your product
meets all safety requirements laid down
for this type of product category.
However special care should be taken
around the rear or the underneath of
the appliance as these areas are not
designed or intended to be touched and
may contain sharp or rough edges, that
may cause injury.
Attention!
The appliance gets very hot, mainly around the cooking areas. It is very important
that children are not left alone in the kitchen when you are cooking.
Do not use a steam cleaner because the moisture can get into the appliance thus
make it unsafe.
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door
glass since they can scratch the surface, which may result in shattering of the
glass.
18
•
Inside of oven: The oven should
always be cleaned after use when it
has cooled down. The cavity should be
cleaned using a mild detergent solution
and warm water. Suitable proprietary
chemical cleaners may be used only
on enamel after first consulting the
instructions supplied with the oven
cleaner and testing a small sample
on the oven cavity. Abrasive cleaning
agents or scouring pads/cloths should
not be used on the cavity surface.
NOTE: The manufacturers of this
appliance will accept no responsibility
for damage caused by chemical or
abrasive cleaning.
Let the oven cool down and pay
special attention not to touch the
hot heating elements inside the
oven cavity.
BURNERS AND PAN SUPPORTS
These parts can be removed and cleaned
as indicated previously.
After cleaning, the burners and their flame
spreaders must be well dried and correctly
replaced.
It is very important to check that the burner
flame spreader and the cap have been
correctly positioned. Failure to do so can
cause serious problems.
Check that the electrode “S” (figs. 7.1,
7.3) next to each burner is always clean to
ensure trouble-free sparking.
Check that the probe “T” (figs. 7.1, 7.3) next
to each burner is always clean to ensure
correct operation of the safety valves.
Both the probe and ignition plug must
be very carefully cleaned.
Note: To avoid damage to the electric
ignition do not use it when the burners
are not in place.
CORRECT REPLACEMENT OF THE
AUXILIARY, SEMI-RAPID AND RAPID
BURNERS
It is very important to check that the burner
flame distributor “F” and the cap “C” have
been correctly positioned (see figs. 7.1,
7.2) - failure to do so can cause serious
problems.
CORRECT REPLACEMENT OF THE
TRIPLE RING BURNER
The triple ring burner must be correctly
positioned (see fig. 7.5); the burner rib
must be enter in their logement as shown
by the arrow (see fig. 7.3).
Then position the cap “A” and the ring “B”
(figs. 7.4, 7.5).
The burner correctly positioned must not
rotate (fig. 7.4).
REPLACING THE OVEN LIGHT BULB
Switch the cooker off at the mains.
When the cooker is cool unscrew and
replace the bulb with another one resistant
to high temperatures (300°C), voltage
230V, 50 Hz, type E14 and same power
(check watt power as stamped in the bulb
itself) of the replaced bulb.
Note: Oven bulb replacement is not
covered by your guarantee.
19
C
F
T
S
Fig. 7.1
Fig. 7.2
S
T
Fig. 7.3
A
B
Fig. 7.4
20
Fig. 7.5
ASSEMBLY AND DISMANTLING OF
THE SIDE RUNNER FRAMES
•
Fit the side runner frames into the
holes on the side walls inside the oven
(Fig. 7.6).
•
Slide the rack and the tray into the
runners (Fig. 7.7).
The rack must be fitted so that the
safety catch, which stops it sliding out,
faces the inside of the oven (fig. 7.7).
•
To dismantle, operate in reverse order.
Fig. 7.6
OVEN TRAY
The oven tray “L” must be inserted into the
side runners (fig. 7.8).
Fig. 7.7
OVEN FLOOR
The oven floor “F” (fig. 7.8) can be easily
removed to facilitate cleaning.
Remember to replace the floor correctly
afterwards.
Be careful not to confuse the tray “L” with
the oven floor “F”.
L
F
Fig. 7.8
21
Fig. 7.9
Fig. 7.10
OVEN DOORS
STORAGE COMPARTMENT
The internal glass panel can be easily
removed for cleaning by unscrewing the
retaining screws (fig. 7.9).
The storage compartment is accessible
through the pivoting panel (fig. 7.10).
Do not use harsh abrasive cleaners or
sharp metal scrapers to clean the oven
door glass since they can scratch the
surface, which may result in shattering
of the glass.
Do not store flammable material in the
oven or in the storage compartment.
22
REMOVING THE OVEN DOOR
The oven door can easily be removed as
follows:
•
Open the door to the full extent (fig.
7.11a).
•
Open the lever “A” completely on the
left and right hinges (fig. 7.11b).
•
Hold the door as shown in fig. 7.11.
•
Gently close the door (fig. 7.11c) until
left and right hinge levers “A” are
hooked to part “B” of the door (fig.
7.11b).
•
Withdraw the hinge hooks from their
location following arrow “C” (fig. 7.11d).
•
Rest the door on a soft surface.
•
To replace the door, repeat the above
steps in reverse order.
Fig. 7.11a
A
B
Fig. 7.11b
Fig. 7.11c
C
Fig. 7.11
Fig. 7.11d
23
Advice for the installer
IMPORTANT
•
•
The appliance is designed and approved for domestic use only and should not be
installed in a commercial, semi commercial or communal environment.
Your product will not be guaranteed if installed in any of the above environments
and could affect any third party or public liability insurances you may have.
The appliance may be installed in a kitchen, kitchen/diner or a bed sitting room, but
not in a room or space containing a bath or a shower without first consulting current
regulations.
The appliance must not be installed in a bed-sitting room of less than 20 m3.
Cooker installation must only be carried out by a SUITABLY QUALIFIED AND
REGISTERED TECHNICIAN and in compliance with local safety standards.
Failure to observe this rule will invalidate the warranty.
•
The appliance must be installed in compliance with regulations in force in your country
and in observation of the manufacturer’s instructions.
•
Always disconnect the appliance from the power supply before carrying out any
maintenance operations or repairs.
•
Take care NOT to lift the oven by the door handle/s.
•
Some appliances are supplied with a protective film on steel and aluminium parts.
This film must be removed before using the cooker.
•
Important: The use of suitable protective clothing/gloves is recommended when
handling or installing this appliance.
24
900
900÷925
WARNING
When
correctly
installed,
your product meets all safety
requirements laid down for this
type of product category.
However special care should
be taken around the rear or the
underneath of the appliance as
these areas are not designed
to be touched and may contain
sharp or rough edges, that may
cause injury.
60
0
8 - INSTALLATION
This cooker has class “2/1” overheating protection so that it can be installed next
to a cabinet.
If the cooker is installed adjacent to furniture which is higher than the gas hob cooktop, a
gap of at least 200 mm must be left between the side of the cooker and the furniture.
The walls and kitchen furniture surrounding the appliance must be made of non-flammable
material. The veneered synthetical material and the glue used must be resistant to a
temperature of 90°C in order to avoid ungluing or deformations. It is recommended that
a 10 mm gap to each side is made if the adjacent kitchen furniture is made of a plastic
laminate wrap.
Curtains must not be fitted immediately behind appliance or within 500 mm of the sides.
It is essential that the cooker is positioned as stated below.
We do not recommend the cooker is located on a plinth. If this is unavoidable, it will be
necessary to provide safety measures to prevent the appliance falling off.
450 mm
650 mm
The cooker must be installed by a suitably qualified technician and in compliance
with local safety standards.
200 mm
500 mm
Fig. 8.1
25
FITTING THE ADJUSTABLE FEET
AND LEVELLING THE COOKER
The adjustable feet must be fitted to the
base of the cooker before use (figs. 8.2,
8.3).
Rest the rear of the cooker on a piece of
the polystyrene packaging exposing the
base for the fitting of the feet.
Fit the 4 legs by screwing them tight into
the support base as shown in figure 8.3.
Fig. 8.2
Fig. 8.3
LEVELLING THE COOKER
The cooker may be levelled by screwing
the lower ends of the feet IN or OUT (fig.
8.4).
Fig. 8.4
26
MOVING THE COOKER
WARNING: When raising cooker to upright position always ensure two people carry
out this manoeuvre to prevent damage to the adjustable feet (fig. 8.5).
Fig. 8.5
WARNING
Be careful: Do not lift the cooker by
the door handle/s when raising to the
upright position (fig. 8.6).
Fig. 8.6
WARNING
When moving cooker to its final position
DO NOT DRAG (fig. 8.7).
Lift feet clear of floor (fig. 8.5).
Fig. 8.7
27
Stability Bracket
We recommend a stability bracket is fitted to the cooker.
The type shown in fig. 8.8 can be purchased from most plumbers merchants and do it
yourself (D.I.Y.) shops.
Existing slot in
rear of cooker
Brackets
Dotted line showing the
position of cooker when fixed
Fig. 8.8
3
Outline of cooker backplate
at the engagement slot
Wall fixing
Floor fixing
Fig. 8.9
28
Provision for Ventilation
•
The appliance should be installed into a room or space with an air supply in accordance
with BS 5440-2: 2000.
•
For rooms with a volume of less than 5m3 - permanent ventilation of 100 cm2 free area
will be required.
•
For rooms with a volume of between 5 m3 and 10 m3 a permanent ventilation of 50 cm2
free area will be required unless the room has a door which opens directly to the outside
air in which case no permanent ventilation is required.
•
For rooms with a volume greater than 10 m3 - no permanent ventilation is required.
Note: Regardless of room size, all rooms containing the appliance must have direct
access to the outside air via an openable window or equivalent.
•
•
Where there are other fuel burning appliances in the same room, BS 5440-2:
2000 should be consulted to determine the correct amount of free area ventilation
requirements.
The above requirements allow also for use of a gas oven and grill but if there are other
gas burning appliances in the same room, consult a qualified engineer.
29
9 - GAS INSTALLATION
IMPORTANT NOTE
This appliance is supplied for use on NATURAL GAS or LPG (check the gas regulation
label attached on the appliance).
•
Appliances supplied for use on NATURAL GAS are adjusted for this gas only and
cannot be used on any other gas (LPG) without modification. The appliances are
manufactured for conversion to LPG.
•
Appliances supplied for use on LPG are adjusted for this gas only and cannot be
used on any other gas (NATURAL GAS) without modification. The appliances are
manufactured for conversion to NATURAL GAS.
If the NATURAL GAS/LPG conversion kit is not supplied with the appliance this kit can be
purchased by contacting the After-Sales Service.
INSTALLATION & SERVICE REGULATIONS (UNITED KINGDOM)
It is a legal requirement that all gas appliances are Installed & Serviced by a competent
person in accordance with the current editions of the following Standards & Regulations or
those regulations appropriate to the geographical region in which they are to be installed:
•
Gas Safety (Installation & Use) Regulations
•
Building Regulations
•
British/European Standards
•
Regulations for Electrical Installation
Installation and service of any gas product must be made by a suitably qualified and
registered person competent on the type of product being installed or serviced and holding
a valid certificate of competence for the work being carried out. Currently the proof of
competence is the Accredited Certification Scheme (ACS) or N/SVQ that has been aligned
to the ACS.
It is also a requirement that all businesses or self employed installers are members of a
class of person approved by the Health and Safety Executive.
Failure to install the appliance correctly could invalidate any manufacturers warranty and
lead to prosecution under the above quoted regulations.
Gas Connection
GB
Cat: II 2H 3+
It is a requirement that a restraining chain (not supplied with the appliance) is also used to
prevent stress being applied to the gas hose or pipework. The chain should be attached
securely to the product and on the wall (fig. 9.1).
30
RESTRAINING CHAIN
Fig. 9.1
Chain
security
holes
Cooker
Back of
the cooker
Rear wall
Installation to Natural Gas
Installation to Natural Gas must conform to the Code of Practice, etc.
The supply pressure for Natural Gas is 20 mbar.
The installation must conform to the relevant British/European Standards.
Installation to LP Gas
When operating on Butane gas a supply pressure of 28-30 mbar is required.
When using Propane gas a supply pressure of 37 mbar is required.
The installation must conform to the relevant British/European Standards.
Warning: Only a suitably qualified and registered installer, also with technical knowledge
of electricity should install the appliance.
He should observe the Regulations and Codes of Practice governing such installation of
gas appliances.
Note: It is recommended that the gas connection to the appliance is installed with a flexible
hose connecting tube made to BS669.
31
Notes:
•
Flexible hoses can be used where the sited ambient temperature of the hose
does not exceed 70°C. These hoses must be manufactured in accordance with
BS669 part 1 and be of the correct construction for the type of gas being used.
•
Gas hoses designed for natural gas MUST NOT be used for supplying LPG gas
(LPG gas hoses can be identified by a either a red band or stripe on the rubber
outer coating of the hose).
The hose should not be crushed or trapped or be in contact with sharp or abrasive edges.
IMPORTANT! It is the responsibility of the gas installer to ensure that the product is
fully tested and commisioned in accordance with current regulations to ensure there
are no gas escapes.
Gas connection (figs. 9.2, 9.3, 9.4)
•
The gas supply must use the nearest gas inlet pipe which is located at the left or the
right hand side at the rear of the appliance.
•
IMPORTANT NOTE: Before connecting the appliance to the gas mains fit the female
connector (supplied with the appliance in a separate kit) to the right or the left inlet pipe
using the fibre washer supplied.
•
IMPORTANT: Check the correct positioning of the connector as per pictures and
always operate using two suitable spanners.
•
The unused end inlet pipe must be closed with the plug and the fibre washer.
•
The hose should not be crushed or trapped or be in contact with sharp or abrasive
edges. It should also not be subjected to corrosion by acidic cleansing agents.
The hose should also be connected in such away that it does not touch the floor and
must hang in a natural loop between the appliance and the bayonet fitting.
•
To avoid damage to the appliance gas rail inlet pipe the fittings should be tightened
using two suitable spanners.
Left gas inlet pipe
Connector
Right gas inlet pipe
Plug
Fig. 9.2
32
Fitting the plug
on the inlet pipe
terminal not used
Fig. 9.3
Cooker
manifold (right
or left inlet pipe)
Fibre
washer (*)
Manifold
male
pipe fitting
10 mm
1/2” G cylindrical
(ISO 228-1) male
20 mm
Manifold
male
pipe fitting
Cooker
manifold (right
or left inlet pipe)
Fibre
washer (#)
1/2” G cylindrical
(ISO 228-1) female
1/2” G cylindrical
(ISO 228-1) male
1/2” G cylindrical
(ISO 228-1) female
Plug (#)
10 mm
1/2” BSP
female
20 mm
Connector
(*)
(*) Supplied with the appliance
in a separate kit
(#) Already fitted on the
right or left inlet pipe
IMPORTANT PRESCRIPTIONS FOR GAS CONNECTION
700 mm
Rear wall
200 mm
Suggested area for
gas mains connection
Fig. 9.4
33
CONVERSION TO NATURAL GAS OR TO LPG
REPLACEMENT OF THE INJECTORS
If the injectors are not supplied they can
be obtained from the After-Sales Service.
Select the injectors to be replaced
according to the “Table for the choice of the
injectors”.
The nozzle diameters, expressed in
hundredths of a millimetre, are marked on
the body of each injector.
Auxiliary,
Semi-rapid and
Rapid burners
J
REPLACEMENT OF THE INJECTORS
OF THE COOKTOP BURNERS
To replace the injectors proceed as follows:
•
Remove pan supports and burners
from the cooktop.
•
Using a wrench, substitute the nozzle
injectors “J” (figs. 9.5, 9.6) with those
most suitable for the kind of gas for
which it is to be used.
Fig. 9.5
Triple-ring burner
J
The burners are conceived in such a
way so as not to require the regulation
of the primary air.
ADJUSTING OF THE MINIMUM OF
THE TOP BURNERS
In the minimum position the flame must
have a length of about 4 mm and must
remain lit even with a quick turn from the
maximum position to that of minimum.
Fig. 9.6
The flame adjustment is done in the
following way:
•
Turn on the burner.
•
Turn the tap to the MINIMUM position.
•
Take off the knob.
•
With a thin screwdriver turn the screw
“F” until adjustment is correct (fig. 9.7).
Normally for LPG, tighten up the
regulation screw.
34
F
Fig. 9.7
TABLE FOR THE CHOICE OF THE INJECTORS
GB
Cat: II 2H3+
BURNERS
Nominal
power
[kW]
Reduced
power
[kW]
Auxiliary (A)
1,00
Semi-rapid (SR)
1,75
Rapid (R)
LPG
G30 28-30 mbar
G31 37 mbar
Natural Gas
G20 20 mbar
Ø
injector
[1/100 mm]
Air ring
opening
[mm]
Ø
injector
[1/100 mm]
Air ring
opening
[mm]
0,30
50
0,45
66
-
77
-
-
101
-
3,00
0,75
87
-
129
-
Triple-ring (TR)
3,50
1,50
93
-
135
-
Oven
6,20
1,30
120
8 (*)
180
1,5 (*)
Grill
4,65
-
107
Fully open (*)
165
3 (*)
(*) = Reference value
AIR VENT NECESSARY FOR GAS COMBUSTION = (2 m3/h x kW)
BURNERS
Air necessary for combustion [m3/h]
Auxiliary (A)
2,00
Semi-rapid (SR)
3,50
Rapid (R)
6,00
Triple-ring (TR)
7,00
Oven
12,40
Grill
9,30
LUBRICATION OF THE GAS TAPS
•
In case of difficulty in the gas taps operation, call Service.
IMPORTANT
All intervention regarding installation maintenance of the appliance must be fulfilled
with original factory parts.
The manufacturer declines any liability resulting from the non-compliance of this
obligation.
35
OPERATIONS TO BE EXECUTED
FOR THE REPLACEMENT OF THE
INJECTORS OF THE OVEN AND
GRILL BURNER
a) oven burner
•
Lift and remove the lower panel inside
the oven.
•
Unscrew and remove the burner
securing screw “A” (fig. 9.8).
•
Slacken screw “B” (fig. 9.8).
•
Withdraw the burner in the manner
shown in figure 9.9 and rest it inside
the oven. Take care not to damage the
wire to the ignition electrode and the
safety valve probe.
•
Using a 10 mm box spanner, unscrew
the injector “U” (indicated by the
arrow in fig. 9.9) and replace with a
new injector selected in accordance
with the “Table for the choice of the
injectors”; then replace the burner
repeating the above steps in reverse
order.
A
Fig. 9.8
36
U
Fig. 9.9
B
b) grill burner
•
Unscrew and remove the burner
securing screw “C” (fig. 9.10).
•
Slacken screw “D” (fig. 9.10).
•
Move the burner in the manner shown
in figure 9.11. Take care not to damage
the wire to the ignition electrode and
the safety valve probe.
•
Using a 10 mm box spanner, unscrew
the injector (indicated by the arrow
in fig. 9.11) and replace with a new
injector selected in accordance
with the ‘Table for the choice of the
injectors’; then replace the burner
repeating the above steps in reverse
order.
C
Fig. 9.11
D
Fig. 9.10
37
REGULATION OF AIR SUPPLY TO
OVEN AND GRILL BURNERS
Using a cross-head screwdriver, slacken
the screw “Q” securing the air flow
regulation collar “P” (figs. 9.12 and 9.13)
and turn the collar forward or backward
to increase or reduce the air aperture
in accordance with gas type and the
indications in the ‘Table for the choice of
the injectors’.
Light the burners and check the flames.
Fig. 9.13
38
Q
P
Ring opening
Fig. 9.12
long, yellow
and trembling
Flame
correct
Flame with
excess
primary air
clear interior
blue cone
short and sharp
too blue interior
cone tending to
detach
CAUSE
air regulating
tube, too
closed
correct
distance of
the tube
air regulating
tube, too
open
ADJUSTMENT OF
BURNER MINIMUM
THE
OVEN
This needs to be done only for the oven
burner (the grill is a fixed capacity) by
acting on the thermostat.
Considering that in the minimum position
the flame must have a length of about 4 mm
and must remain lit even with a brusque
passage from the maximum position to that
of minimum.
The flame adjustment is done in the
following way:
•
turn on the burner by setting the
thermostat knob on position 10
(maximum);
Flame correct
•
Flame faulty in
primary air
remove the knob and unscrew the
by-pass screw “G” (fig. 9.14) about
three times by passing a small flat
screwdriver (Ø 3 mm blade, 100 mm
length) through the panel opening;
•
re-mount the knob and let the oven
heat up for about 10 minutes, then
bring the knob to position 1 (minimum)
to operate the thermostat by-pass;
•
after having removed the knob again
and being very careful not to turn the
tap rod, slowly screw the by-pass
screws “G” (fig. 9.14) until you obtain
a flame of 3-4 mm in height.
Flame with exces s
primary air
Normally for LPG (G30/G31), tighten up
the regulation screw.
Fig. 9.14
G
Flame faulty
in primary
air
G
39
10 - ELECTRICAL INSTALLATION
IMPORTANT: The appliance must be installed in accordance with the manufacturer’s
instructions. Incorrect installation, for which the manufacturer accepts no
responsibility, may cause damage to persons, animals or property.
The connection of the appliance to earth is mandatory. The manufacturer declines
all responsibility for any inconvenience resulting from the inobservance of this
condition.
Before carrying out any work on the electrical parts of the appliance, the appliance
must be disconnected from the mains.
FOR YOUR SAFETY PLEASE READ THE FOLLOWING INFORMATION:
This appliance must be installed by a qualified technician according to the current local
regulations and in compliance with the manufacturer instructions.
This appliance is supplied with a moulded 13 amp three pin mains plug with a 3 amp fuse
fitted. Should the fuse require replacement, it must be replaced with a fuse rated at 3 amp
and approved by ASTA or BSI to BS 1362.
The plug contains a removable fuse cover that must be refitted when the fuse is replaced.
In the event of the fuse cover being lost or damaged, the plug must not be used until a
replacement cover has been obtained. Replacement fuse covers can be purchased from
your nearest electrical dealer and must be the sarne colour as the original.
IF THE MOULDED MAINS PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR
HOME OR IS REMOVED FOR ANY OTHER REASON, THEN THE FUSE SHOULD BE
REMOVED AND THE CUT OFF PLUG DISPOSED OF SAFELY TO PREVENT THE
HAZARD OF ELECTRIC SHOCK.
THERE IS A DANGER OF ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED
INTO ANY 13 AMP SOCKET OUTLET.
If a replacement plug is to be fitted, please observe the wiring code shown below.
Warning! This appliance must be earthed.
A properly earthed three pin plug (fused at 3 amps, to BS 1362 ASTA approved) must be
used. As the colours of the wires in the mains lead of this appliance may not correspond with
the coloured markings identifying the terminals
in your plug, proceed as follows:
•
The wire which is coloured GREEN &
YELLOW must be connected to the
terminal in the plug which is marked with
” or
letter “E” or by the Earth symbol “
coloured GREEN & YELLOW.
•
The wire which is coloured BLUE must be
connected to the terminal which is marked
with the letter “N” or coloured BLACK.
•
The wire which is coloured BROWN
must be connected to the terminal which
is marked with the letter “L” or coloured
RED.
40
Green & Yellow
Earth
Blue Neutral
Fig. 10.1
3 amp fuse
Brown Live
ELECTRICAL FEEDER CABLE REPLACEMENT
WARNING: If the power supply cable is damaged, it must be replaced only by an
authorised service agent in order to avoid a hazard.
To connect the supply cable:
•
Remove the screw securing the cover “A” on the rear of the cooker (fig. 10.2).
•
Unscrew cable clamp “D” (fig. 10.3).
•
Connect the wires to the terminal block “B” as shown in the diagram in figure 10.4.
•
Take up any slack in the cable and secure with the cable clamp “D”.
•
Replace the cover “A”.
NOTE: The earth conductor must be left about 3 cm longer than the others.
FEEDER CABLE SPECIFICATIONS
Type “H05V2V2-F”
230 V~ 3 x 0,75 mm2
B
D
A
Fig. 10.2
Fig. 10.3
230 V
L1 PE N (L2)
Fig. 10.4
41
11 - GUARANTEE
Your new “De’Longhi” product comes with 12-month guarantee covering all parts and
labour.
If your appliance proves to be defective as a result of faulty materials or workmanship
during the guarantee period, these parts will be repaired or replaced free of charge.
AFTER SALES SERVICE
Should you require service, spares or product information and advice:
• Please Telephone 0843 362 2013.
• Details of your purchase receipt will be required if you require service within the first
12-month of purchase.
1. The rights and benefits under this guarantee are additional to your statutory rights,
which are not affected by this guarantee.
2. The manufacturer undertakes within the specified period, to repair or replace free of
charge any parts of the appliance found to be defective provided that:
• We are promptly informed of the defect.
• The appliance is installed and used in accordance with the written instructions
enclosed with the appliance.
• The appliance is used only on an electrical supply as indicated on the rating label
fixed to the appliance.
• The appliance has not been altered in any way or subject to misuse or repaired by
a person other than an authorised service agent.
3. No rights are given under this guarantee to a person acquiring the appliance second
hand or for commercial, semi-commercial or communal use.
4. This guarantee applies throughout the UK and Channel Islands.
5. Any repaired or replacement appliances will be guaranteed on these terms for the
unexpired portion of the guarantee.
Ser. Nr.
Fig. 11.1
42
43
Desc ri ptio n s an d illu st r ations in this book let ar e gi v e n a s s i m p l y i n d i c a t i v e .
The man u f actu rer res er ves the r ight, cons ider in g t h e c h a ra c t e r i s t i c s o f t h e
model s described h e re, at any tim e and w ithout notic e , t o m a k e e v e n t u a l n e c e s s a r y
modifi c atio n s fo r th e ir cons tr uction or for com m er c i a l n e e d s .
w w w. de l on g hi - co o ke r s. co . uk
Cod . 1 1 0 4 3 8 5 - ß 1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising