EverFocus | EBD930 eZ.HD Series | User`s manual | EverFocus EBD930 eZ.HD Series User`s manual

EBD930 eZ.HD Series
720p Analog High Definition
True Day/Night Outdoor IR Ball Camera
User’s Manual
Copyright © EverFocus Electronics Corp,
Release Date: Nov., 2014
Precautions
1.
Do not install the camera near electric or magnetic fields. Install the camera away from
TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the
electromagnetic fields generated from these devices may distort the video image or
otherwise interfere with camera operation.
2.
Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein. Improper disassembly or introduction of
corrosive materials may result in equipment failure or other damage.
3.
Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may
cause permanent damage to the sensor and/or internal circuits, as well as creating
unbalanced illumination beyond the capability of the camera to compensate.
4.
Keep the power cable away from water and other liquids and never touch the power cord
with wet hands. Touching a wet power cord with your hands or touching the power cord
with wet hands may result in electric shock.
5.
Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may
result in equipment failure, electric shock or, in extreme cases, fire.
6.
Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor
directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean
the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera
body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any
part of the camera.
7.
Do not operate the camera beyond the specified temperature, humidity or power source
ratings. This camera is suitable for indoor operation only. Use the camera at temperatures
within -10°C~50°C (14°F~122°F) and humidity less than 80%; this device is not rated as
submersible. The input power source is 12VDC. Be sure to connect the proper + / - polarity
and voltage, as incorrect polarity or too high a voltage will likely cause the camera to fail,
and such damage is not covered by the warranty.
8.
Mounting. Use care in selecting a solid mounting surface which will support the weight of
the camera plus any wind, snow, ice or other loading, and securely attach the camera to the
mounting surface using screws and anchors which will properly support the camera. If
necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional
support for the camera.
2
Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
3
Contents
1.
Introduction...................................................................................................................... 5
1.1
1.2
Packing List ..................................................................................................................... 5
Features .......................................................................................................................... 5
2.
Cable Description .............................................................................................................. 6
3.
Installation ....................................................................................................................... 7
3.1
Installation and Adjustment ........................................................................................... 7
4.
Configuration in the OSD Menu ........................................................................................11
5.
Specifications...................................................................................................................15
4
EBD930 eZ.HD IR Mini Ball Camera
1.
Introduction
The EBD930 ball camera is equipped with a 1/2.8" SONY 1.37M pixels CMOS sensor and providing
high resolution of 720p. Featured with the Digital Wide Dynamic Range (D-WDR) function, the
camera can provide clear images even under back light circumstances where intensity of
illumination can vary excessively.
The EBD930 comes with 24 IR LEDs, supporting up to 15m (~50ft.) IR distance in night vision. The
camera can work in both indoor and outdoor environments. The IP66-rating and vandal proof
housing make it suitable for outdoor use. The EBD930 supports both NTSC and PAL scanning
systems, which can be switched via OSD.
1.1 Packing List




Camera Body x 1
User Manual x 1
DC Power Pigtail Cable x 1
Set Screw x 2




Mounting Screw x 4
Plastic Anchor x 4
Hexagon Wrench x 1
Template Plate x 1
1.2 Features

720p with high flexibility and performance for astounding image

1/2.8" SONY 1.37M pixels CMOS, delivers amazing high sensitivity

24pcs IR LEDs for 15m/50ft.range (depending on scene IR reflectivity)

D-WDR to improve the visibility under high contrast scene

Provides 3D Noise Reduction ensures less blurry moving subjects, vivid and high SN ratio
images even under low light environments

Support 720p & 960H analog signal output, which can be easily switched by OSD

Special design, easy installation and operation
5
EBD930 eZ.HD IR Mini Ball Camera
2.
Cable Description
No.
Name
Descriptions
1
Power Cable
Connect to a 12VDC power source.
2
Dual Video Output
720p and 960H output, using a 75 Ohm BNC-type coaxial cable.
3
DC Power Pigtail Cable
Optional power pigtail cable. The red wire is positive (+);
while the black wire is negative (-).
6
EBD930 eZ.HD IR Mini Ball Camera
3.
Installation
3.1 Installation and Adjustment
1.
For Ceiling Mount / Wall Mount users: Stick the Template Plate on the position where
you want to attach the camera.
2.
Drill four holes and insert the supplied Plastic Anchors into the holes.
If you wish to run the wires into the wall, then drill the circle in the middle of Template
Plate.
7
EBD930 eZ.HD IR Mini Ball Camera
3.
Unscrew the outer housing by twisting it counterclockwise and then remove the outer
housing from the camera base.
4.
Screw the base plate to the wall or ceiling with supplied four Screws and Hexagon
Wrench.
a. If you want to wire the cables from the side cut of the camera base, attach the camera
body to the base plate and run the cables through the camera base first, then screw
the camera base to the ceiling / wall.
8
EBD930 eZ.HD IR Mini Ball Camera
b. If you want to wire the cables through the wall, attach and screw the camera base to
the ceiling / wall. Then attach the camera body to the base plate.
5.
Connect the camera to the 12VDC power source using the supplied DC Power Pigtail
Cable or power adapter.
6.
Connect the camera to an AHD DVR or a portable monitor using the video output cable
for viewing the video image while adjusting camera angles. To configure camera settings
using the OSD Menu Joystick.



Push the Joystick up / down to select
among menu items.
Push the Joystick left / right to adjust
the level of the selected item.
Press the Joystick to enter the submenu
or exit the OSD Setup Menu.
9
EBD930 eZ.HD IR Mini Ball Camera
Note: The function button is not only for direction control, also for switching video format
and video output. Please follow the detailed instruction as below:
 Push the joystick "down" button key over 5 seconds to switch video format from
PAL to NTSC.
 Push the joystick "left" button key over 5 seconds to switch video output from
720p to 960H (720p is the default).
 Push the joystick "right" button key over 5s to switch video output from 960H to
720p.
7.
Screw back the outer housing and adjust the camera angle simultaneously.
8.
Screw the two set screw by using the supplied Hexagon Wrench.
10
EBD930 eZ.HD IR Mini Ball Camera
4.
Configuration in the OSD Menu
You can use the Joystick on the rear panel of the camera to configure camera settings in the OSD
menu. For details on the OSD menu structure as below:
No.
Main
Sub Menu
1
Lens
Manual*
Sub Menu / Function
NTSC: 1/30, 1/60, FLK, 1/240, 1/480, 1/1000, 1/2000, 1/5000,
Shutter
AGC
1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto*
PAL: 1/25, 1/50, FLK, 1/200, 1/400, 1/1000, 1/2000, 1/5000,
1/10000, 1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto*
0 – 15(15*)
Off*
Sens-up
2
Exposure
Brightness
Auto
Sens-up
X2, X4*, X6, X8, X10, X15, X20,
X25, X30
Level
0-8(8*)
Pos/Size
Position, Size,↑,↓,→,←
Gradation
0-2(0*)
1-100(40*)
Off*
D-WDR
On
Auto
Off*
Defog
Auto
Default
Off*
BLC
Level
Middle*, High, Low
Area
Position, Size,↑,↓,→,←
Default
Select
3
Backlight
Display
HSBLC
Area1*, Area2, Area3, Area4
Off
On*
Black Mask
On*/Off
Level
0-100(20*)
Model
All Day*
Night
Default
4
White
Balance
Position, Size,↑,↓,→,←
ATW*
AWC→SET
11
AGC Level
0-255(48*)
EBD930 eZ.HD IR Mini Ball Camera
Indoor
Outdoor
Manual
Blue
1-500(50*)
Red
0-100(50*)
D→N(Delay)
0-60(1*)
N→D(Delay)
0-60(1*)
D→N(AGC)
1-255(240*)
D→N(Delay)
0-60(1*)
N→D(AGC)
1-255(50*)
N→D(Delay)
0-60(5*)
Burst
Off*/On
AWB
Ext*
Auto
5
Day &
Night
Color
Off
B/W
IR Smart
IR PWM
6
NR
On*
Level
0-15(4*)
Area
Position, Size,↑,↓,→,←
Off
0-100(100*)
2DNR
Middle*/Low/Off/High
3DNR
Middle*/Low/Off/High
Off*
Cam Title
D-effect
On
0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ▶→
←↑↓()ˉ-_▊/=&:~,.
Freeze
Off*/On
Mirror
Off*, Mirror, V-flip, Rotate
Neg. Image
Off*/On
Off*
Select
7
Special
Display
Motion
On
Area1*,Area2,Area3,Area4
On*
Position, Size,↑,↓,→,←
Off
Sensitivity
0-100(64*)
Color
Green*, Blue, White, Red
Trans
1.00*,0.75,0.50,
0.25
Alarm
12
View Type
Off, Block, Outline, All*
OSD View
On*/Off
Alarm Out
On*/Off
Alarm Sig
High*, Low
EBD930 eZ.HD IR Mini Ball Camera
Time
1-15(3*)
Default
Off
Select
Area1*,Area2,Area3,Area4
Off
Display
Privacy
On
Color*
Position, Size,↑,↓,→,
←
Mosaic
Position, Size,↑,↓,→,
←
Inv
Position, Size,↑,↓,→,
←
Color
White*, Black, Red, Blue, CYAN,
Yellow, Green
Trans
1.00*,0.75,0.50,
0.25
Default
Language
ENG*/CHN1/CHN2/GER/FRA/ITA/SPA/POL/RUS/POR/NED/TUR
Off
Live DPC
On*
AGC level
0-255(65*)
Level
0-100(100*)
Pos/Size
Position, Size,↑,↓,→,
←
Start
Close the iris then press
DPC View
Off*/On
Level
0-60(5*)
AGC
0-14(14*)
Sens-up
x2*, x4, x6, x8,x10, x15,
x20, x25, x30
Pos/Siz
Position, Size,↑,↓,→,
←
Start
Press Enter
DPC View
Off*/On
Level
0-255(255*)
Off
White DPC
On*
Defect
Off*
Black DPC
RS485
On
CAM ID
0-255(1*)
ID Display
Off*/On
Baud Rate
2400,4800,9600,19200 ,38400
13
EBD930 eZ.HD IR Mini Ball Camera
Off
Sharpness
Auto*
CRT
8
Level
0-10(6*)
Start AGC
0-255(50*)
End AGC
0-255(200*)
Black Level
0-60(0*)
Blue Gain
0-100(50*)
Red Gain
0-255(50*)
Adjust
CRT/LCD
Gamma
LCD*
LSC
Exit
5,0.90,
0.95,1.00
Blue Gain
0-100(50*)
Red Gain
0-100(50*)
Off*/On
Video. Out PAL/NTSC
9
User*,0.45,0.50,0.55,0.6
0,0.65,0.70,0.75,0.80,0.8
Save& END /Reset/Not Saved
14
EBD930 eZ.HD IR Mini Ball Camera
5. Specifications
P/N
EBD930
Pickup Device
1/2.8" SONY 1.37M pixels CMOS
Video Format
NTSC and PAL( can be switched via OSD)
Picture Elements
1280 (H)*720 (V)
Scanning System
Progressive Scan
Sensitivity
0 lux with IR on
S/N Ratio
Over 48dB (AGC off)
Electronic Shutter
AUTO, Manual (X30~1/ 50000), FLK
Video Output
BNC 1.0 Vp-p ,75ohm
Gamma Correction
0.45
Lens Type
2.8mm/3.6mm/6mm Fixed lens with ICR
BLC
OFF/HSBLC/BLC Selectable
AGC
0~15 Levels
White Balance
ATW/AWC-SET/INDOOR/OUTDOOR/MANUAL/AWB
Sync Mode
Internal
Day/Night
Ext, Auto, Color, B/W
IR LED /Distance
24 Units. Up to 15m/50ft. (depending on scene IR reflectivity)
OSD Languages
12-Language
DNR
2DNR/3DNR, Off
DEFOG
Off/Auto(under B/W mode)
D-WDR
On/Off
Sens-up
Off/On(x30~x2)
Mirror
Off, Mirror, V-flip, Rotate
Motion Detection
Off/On for 4 selectable zones
Privacy Mask
Off/On for 4 selectable zones
Environment
IP66 Weather Resistant
Power Source
12VDC
Power Consumption
2.5w max.
Operating Temperature
-10°C~50°C / 14°F~122°F
Humidity
Less than 80%
Dimensions
93 x 65mm / 3.66” x 2.56”
Weight
400g / 0.352lbs.
Certifications
CE / FCC / Rohs
Specifications and designs are subject to change for improving the functionality of this product
without notice.
15
EBD930 eZ.HD IR Mini Ball Camera
EverFocus Electronics Corp.
EverFocus Taiwan:
12F-1, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Taipei City, Taiwan
TEL: +886 2 2698 2334
FAX: +886 2 2698 3943
www.everfocus.com.tw
marketing@everfocus.com.tw
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: +49 2822 93940
FAX: +49 2822 939495
www.everfocus.de
sales@everfocus.de
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: +86 10 6297 3336~39
FAX: +86 10 6297 1423
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: +86 755 2765 1313
FAX: +86 755 2765 0337
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010,
USA
TEL: +1 626 844 8888
FAX: +1 626 844 8838
www.everfocus.com
sales@everfocus.com
EverFocus USA - New York:
415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA
TEL: +1 631 436 5070
FAX: +1 631 436 5027
www.everfocus.com
sales@everfocus.com
EverFocus Japan:
3F Kuramochi, Buildingll 2-2-3 Koto-Bashi,
Sumida-Ku Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
FAX: +81 3 5625 8189
www.everfocus.co.jp
info@everfocus.co.jp
EverFocus China - Shanghai:
Room 403, Ruijin Business Center, No.96, Zhaojiabang
Road, Luwan district, Shanghai 200020, China
TEL: +86 21 6471 2229 / 6471 2291
FAX: +86 21 6471 0566
www.everfocus.com.cn
marketing@everfocus.com.cn
EverFocus India:
UBS, 629/1243, 1st Floor, G Block, Behind
Teacher’s Colony,Bandra Kurla Complex,
Bandra (E), Mumbai 400 051, India
TEL: +91 22 6726 4500
FAX: +91 22 6726 4518
www.everfocus.in
sales@everfocus.in
Your EverFocus product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed ofseparately from
your household waste.
Please, dispose of this equipment at your
local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit
qualitativ hochwertigen Materialien
und Komponenten, die recycelt und
wieder verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling
Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
Download PDF