2008-2010 6.4L Ford / FP-100 / FP-150

2008-2010 6.4L Ford / FP-100 / FP-150
#9
INSTALLATION MANUAL
MODEL FP-100 & FP-150
With New Quick Connect Components!
FORD POWERSTROKE
6.4L DIESEL ENGINE
PLEASE READ THESE INSTRUCTIONS THOROUGHLY
BEFORE BEGINNING INSTALLATION!
PureFlow AirDog
705 MAUSOLEUM ROAD
SHELBYVILLE, IN 46176
1-877-421-3187
www.pureflowairdog.com
CANADIAN PATENT
2,108,391
PROTECTED BY
US PATENTS
5,355,860; 5,746,184; 6,729,310
AUSTRALIAN PATENT
2005101054
NEW ZEALAND PATENT
532356
Additional Foreign Patents Pending in Europe, South America, Mexico, Japan, and China!
Approved for Sale and Use in California by CARB!
SMALL and COMPACT
7” Long X 3.2” Wide X 10” Tall
2
OVERVIEW
Welcome to PureFlow® AirDog®
Fuel Air Separation, Filtration and Delivery System for the Diesel Engine
The AirDog® Fuel Air Separation system is a Premium lift pump and filtration
system for the Ford PowerStroke 6.4L diesel engine. A complete installation kit is
included.
The AirDog® delivers clean fuel to the engine free of virtually all air/vapor and at
a positive flow. Thus, allowing the engine “test cell” performance and efficiency,
while in “real world” use.
The AirDog® FP-100 flows 100 GPH and is recommended for stock and slightly
modified PowerStroke Diesels.
The AirDog® FP-150 is recommended for highly modified PowerStroke Diesels.
PureFlow products are manufactured with a personal touch,
unsurpassed attention to detail
and
the most stringent quality control!
TYPICAL INSTALLATION LAYOUT
High Pressure
Fuel Pump
Figure 1
®
The AirDog draws fuel from the fuel tank at a constant flow, removing water, particulates, and
air/vapor while maintaining a regulated pressurized fuel flow to the stock OE high pressure
pump. The air/vapor separated from the fuel by the AirDog® is returned to the fuel tank.
NOTE: The pictures used in this manual are for example only and may not be exactly the same
as your truck.
3
PureFlow AirDog
QUICK CONNECT COMPONENT OVERVIEW
Provided in this kit is an OE style quick connection system. This system works to
allow for a quick, clean, and professional install.
SAE J2044 Quick Connect System
The SAE J2044 quick connect system is the most commonly used system in the
automotive industry. The images below show the formation of SAE J2044
connection. To connect the assemblies, simply insert the male end form into the
mating female connector. Push firmly until you hear it “click” into place. To
disconnect the fittings, press down and hold the blue tabs on the female connector
while you firmly pull the assembly apart.
4
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
Table of Contents
Section 1
TABLE OF CONTENTS
Section 1……………………………….…….………..….….Table of Contents
Section 2………………………….……….Installation and Safety Guidelines
Section 3………………………….…….…….………………….…….Parts List
INSTALLATION PROCEDURES
Section 4…………………….………………….AirDog® & Mounting Brackets
FUEL LINES
Section 5 A……………………………………………..……….Fuel To Engine
Section 5 B……………………...……….……..….………Fuel Return to Tank
Section 5 C……………………..……………….…….Suction line For FP-100
Section 5 D…………………………………...Suction Line For FP-150
(Includes Hi Flow Suction Tube)
ELECTRICAL HARNESS
Section 6…..…………………………………...…..…….….Electrical Harness
Section 7..………….…………………….……….……….…...Final Check List
MAINTENANCE
Section 8…………………..……………..…Filter Service Recommendations
Section 9…………………..………….…….Cleaning the Gearotor Assembly
5
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
Installation & Safety Guidelines
Section 2
AirDog®
MODEL FP-100 & FP-150
The installation of your AirDog® can be made relatively easy by following the steps outlined in
this manual, and:
1. Inventory the package components completely. Notify PUREFLOW®AIRDOG immediately
of any parts missing or damaged.
2. Read the installation manual completely. Understand how the system operates and
installation recommendations before beginning installation.
3. The installation recommendations contained herein are suggested installation guidelines
only. Individual installations may vary.
4. If any installation procedure is uncertain, contact PUREFLOW® AIRDOG for
technical assistance.
5. When installing the AirDog® fuel lines be sure to keep the ORIGINAL ENGINE RETURN
LINE connected as it is from the factory!
SAFETY GUIDELINES!
CAUTION! Please be sure to chock the vehicle’s tires to prevent rolling.
CAUTION! Please use proper supports when working beneath an
elevated vehicle.
CAUTION! Most diesel pickups have two (2) 12volt batteries. Disconnect the battery cables
to both batteries before proceeding with the AirDog® installation.
CAUTION! Vehicle frame rails should not be drilled into or welded upon.
CAUTION! Wear safety glasses when operating power tools such as drills and grinders or
when using a punch or chisel.
CAUTION! Use common sense when routing fuel lines and electrical harnesses. Keep them
away from hot exhaust components and/or moving parts. Properly secure lines to
prevent chaffing.
Use Good Judgment and Common Sense When Installing the AirDog®!
6
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
Parts List
Section 3
PowerStroke Parts List
QTY
DESCRIPTION
Part Number
1
Installation Manual
ADI-F-100/150
FP-100
1
AirDog®
1
®
AirDog Mounting Bracket
1
Mounting Hardware Kit,
1
Frame Bracket
1
Wiring Harness
010-3C-0002PC
010-3C-0001PC
5E-2-010
1
Return Fuel Filler Tube (with 2 Clamps)
001-4A-1-0150
1
Bundle of Plastic Ties
1
High Flow Suction Tube (For FP-150’s Only)
1
Grommet (For FP-150’s Only)
1
Spacer
010-3C-0003-A-P
1
Suction Hose Assembly
WAP110-8-8-90
1
Return Hose Assembly
WAP110-8-8-90
1
Pressure Hose Assembly
WAP121-8-8
1
Customer Service Oring Replacement Kit
901-05-0101
3
Push Lock Hose Splice
2
1/2” Male SAE J2004 Quick Connect x 3/8” NPTF
Or
FP-150
001-3C-0004
901-61-0102-PM-F
5H-2-1-06/12
WAP108
5J-1-1-04-0001
001-4A-1-0026
7
08J2044-3/8 NPTF
IMAGE
ILLUSTRATION OF QUICK CONNECT COMPONENTS
8
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
AirDog® & Mounting Brackets
Section 4
Installing the AirDog® & Mounting Brackets on the Truck’s
Frame.
Figure 2
4-1
Figure 3
Figure 4
Assemble the AirDog® mounting bracket to the frame bracket. Use the spacer block to
adjust the AirDog® to clear lines and wiring harnesses on the frame. Also adjust the
assembly up or down on the frame bracket as needed for clearance.
Figure 5
Figure 6
Figure 7
FUEL IN
4-2
ENGINE
Install a 1/2” Male SAE J2004 Quick
Connect x 3/8” (08J2044-3/8NPTF) into
the “ENGINE” and “FUEL IN” ports in
the AirDog®.
Figure 8
WARNING: The NPT fitting threads must be lubricated with oil or anti-seize compound
before installation to prevent galling!
NOTE: The AirDog® can be mounted on either the inside or the outside of the frame, as
space or personal choice dictates.
Outside the Frame
Inside the Frame
Figure 9
Figure 10
9
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
AirDog® & Mounting Brackets
Section 4
Installing the AirDog® & Mounting Brackets on the Truck’s
Frame, cont’d.
NOTE: You may attach the AirDog® to the bracket either before or after attaching the
assembly to the frame, whichever is easier. Mount the AirDog® so the “FUEL IN” port is
directed toward the rear of the vehicle.
Figure 11
Figure 12
4-3
Loose assemble the AirDog® and brackets to the vehicle by clamping the frame
between the mounting plate and back plate with bolts, lock washers, and nuts.
Figure 13
4-4
Position the AirDog® on the frame as necessary, for clearance. Properly torque the
fasteners!
10
AirDog® FP-100 & FP-150
Section 5-A
Ford PowerStroke 2008 6.4L
Fuel Lines
AirDog®II Fuel Line to the Engine.
5A-1. Disconnect the fuel supply line to the engine from the OE fuel pump. This pump is
located on the driver’s side inside frame rail.
Fuel Pump with 1/2” Quick Connect Fitting
To Engine
Figure 14
DISCONNECT HERE
View from Front
Figure 15
View From Below
5A-2 Insert the female quick connect end (see figure 16) of the “pressure hose
assembly” into the male quick connect fitting previously installed in the port
marked “ENGINE”. You will hear a “click” when it connects.
Figure 16
5A-3. Connect the other end of the “Pressure Hose Assembly” (Figure 17) to
The original factory engine supply line shown in figures 14 & 15. It will “click” when
properly connected.
Figure 17
5A-4 Any excess fuel hose can be addressed by routing the hose in a fashion to take up the
extra length, or a section of the hose can be removed. Push lock splices have been
included if you choose to remove the excess hose.
11
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
Fuel Lines
Section 5-B
Fuel Return Line from the AirDog® to the Tank.
Installing the fuel 'Return to Tank' assembly in Filler Tube
Filler
Tube
Fuel
Return
Fitting
Hose Clamp
Fuel Tank
Figure 18
5B-1. Cut filler tube as illustrated, removing ½ inch. Loose assemble clamps on each end of
filler tube.
Figure 19
Figure 20
5B-2. Insert “Return Fuel Filler Tube” assembly in filler tube. INSTALL THE FILLER TUBE
WITH ARROWS POINTING TOWARD THE TANK!! SEE FIG 19
Properly tighten clamps.
5B-3.
Insert the SAE J2044 female quick connect end( see Figure 20) of the “Return Hose
Assembly” into the pre-installed male fitting in the port marked “Tank”.
The fitting will “click” when properly installed.
5B-4
Attach the other end of the “Return Hose Assembly” onto the male end form of the
“Return Fuel Filler Tube” installed in step 5B-2. A ”click” will be heard when the
fitting is properly connected.
5B-5
Any excess fuel hose can be addressed by routing the hose in a fashion to take up
the extra length, or a section of the hose can be removed. Push lock splices have
been included if you choose to remove the excess hose.
12
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
Fuel Lines
Section 5-C
Section 5-C: Fuel Suction Line for AirDog® FP-100.
NOTE: The AirDog® FP-150 requires a High Flow Suction Tube. If you are installing an
AirDog® FP-150 skip Section 5-C and go to section 5D.
5C-1.
Insert the female quick connect end (see figure 21) of the “Suction Hose Assembly” to
the male fitting installed in the “Fuel In” port during step 4-3 of this manual. A “click”
will be heard when the fitting is properly connected.
Figure 21
5C-2. Remove the original fuel suction line Quick Connect fitting from fuel tank by squeezing
the tabs on the end of the connector together. Do Not mistake the return line with the
suction line. Consult your factory manual if unsure of these procedures.
Figure 23
Figure 22
Suction Line
In More Detail
To release the quick-connect fitting from the fuel tank suction tube, push the fitting toward the
suction tube. With the plastic tabs firmly depressed, pull the fitting assembly from the suction
tube. Hold the Quick Connect Fitting square to the suction tube. It may be difficult to
disconnect the fitting it is cocked or becomes cocked during removal.
5C-3. Attach the other end of the “Suction Hose Assembly” to the male quick connect on the
top of the fuel module where the factory suction line was once located. A “click will be
heard when the assembly is properly connected. (Figure 23)
5C-4. Any excess fuel hose can be addressed by routing the hose in a fashion to take up
the extra length, or a section of the hose can be removed. Push lock splices have
been included if you choose to remove the excess hose.
13
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
Fuel Lines
Section 5-D
INSTALLING THE AIRDOG® FP-150
HIGH FLOW SUCTION TUBE.
The AirDog® 150 includes a ½” High Flow suction tube to accommodate the high flows of this
system. To install the ½ suction tube it is necessary to either drop the fuel tank or to lift the
truck bed.
NOTE: Should you choose to drop the fuel tank, support the tank as it is when it is installed on
the truck. If you let it rest flat on the floor, the tank may squash out and the suction tube will be
too short after the tank is re-installed in the truck. The suction tube, being cut too short may
suck air as the fuel drops below ¼ tank level.
NOTE: Should you choose to pull the pickup bed to access the tank. Be sure to disconnect the
tail light wires, fuel tank filler tube, and any other accessories or components that may be
secured to the frame and bed.
When Dropping the Tank, Always Remember Safety First!
Figure 24
Figure 25
Figure 26
If you choose to remove the bed, properly support the truck bed to prevent
serious injury or death!
Figure 27
Figure 28
14
PureFlow AirDog
®
AirDog FP-100 & FP-150
Ford PowerStroke 2008 6.4L
High Flow Suction Tube
Section 5-D
INSTALLING THE HIGH FLOW SUCTION TUBE, Cont’d.
NOTE: The fuel tank used for the pictures is an example only and may not be exactly the same
as your tank.
IMPORTANT: Select a location for the suction tube that has adequate clearance
below the bed. Also consider that under hard acceleration, fuel will migrate
toward the back of the fuel tank.
5D-1. Remove the collection basket.
Figure 29
Figure 30
5D-2. Drill a 1-1/8” hole at the selected location in the fuel tank for the suction tube. Hold
a container below the drill point to catch debris.
Figure 31
Figure 32
5D-3. Remove all burrs from the edge of the hole.
Figure 33
5D-4. Install the grommet in the new suction tube access hole.
15
Figure 34
PureFlow AirDog
®
AirDog FP-100 & FP-150
Ford PowerStroke 2008 6.4L
High Flow Suction Tube
Section 5-D
INSTALLING THE HIGH FLOW SUCTION TUBE, Cont’d.
5D-5. Measure and cut the suction tube to a length that will allow approximately 1/8”
clearance off the bottom of the tank. It is suggested to form the end of the tube similar to
Figure 38.
Figure 35
5D-6. Lubricate the bulkhead fitting with motor oil. Pressing firmly, insert the suction tube
assembly into the grommet. Be sure the bulkhead fitting is completely seated in the
grommet.
Figure 36
Figure 37
5D-7. Re-install the Collection basket.
Re-install the factory return line to the proper
port of the Collection basket before the tank
is fully re-installed.
Figure 38
5D-8. Connect the end of the “Suction Hose Assembly” to the bulk head fitting while it is
easily accessible. A “click” will be heard when it is properly installed.
5D-9 Any excess fuel hose can be addressed by routing the hose in a fashion to take up
the extra length, or a section of the hose can be removed. Push lock splices have
been included if you choose to remove the excess hose
16
PureFlow AirDog
®
AirDog FP-100 & FP-150
Ford PowerStroke 2008 6.4L
High Flow Suction Tube
Section 5-D
INSTALLING THE HIGH FLOW SUCTION TUBE, Cont’d.
5D-10. If the fuel tank was dropped to install the suction tube, re-install the fuel tank. If the
truck bed was removed, reinstall the bed.
17
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
Electrical Harness
Section 6
The AirDog® is equipped with a relay controlled wiring harness.
WIRING DIAGRAM (In Red)
High Pressure
Fuel Pump
Figure 39
The AirDog® wiring harness.
AirDog® Pump Motor Lead
Pressure Sensor/Switch Lead
Indicator Light Lead
Battery Positive Lead
Battery Negative Lead
Mini Fuse Tap Relay Lead
Figure 43
CAUTION: If the OPTIONAL Low Pressure Indicator Light is not used, be sure to insulate
the two (2) #10 Indicator Light connectors to prevent accidental contact.
Securing the Relay and Fuse Holder to the Vehicle
6-1.
Secure the relay and fuse holder to the vehicle.
Figure 40
Figure 41
18
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
Electrical Harness
Section 6
Connecting the AirDog® Relay Control Lead
Figure 42
6-3. Route the AirDog® 'Relay activation lead', the Red (+) wire with the mini fuse tap
attached, to the OE fuel pump. Remove the mini fuse tap and splice the relay lead to the
OE fuel pump lead.
NOTE: The power supply leads can be connected to the battery or the alternator. Connecting
the power supply leads to the alternator instead of the battery will create a corrosion free
connection.
Black (-)
Red (+)
6-4. Route the power supply leads to the alternator.
Connect the Black (-) lead to the alternator
Ground connection.
Connect the Red (+) lead to the alternator Hot
Lead going to the battery.
Figure 43
OR
6-5.
Should you choose to connect the power
supply leads directly to the battery, connect
the RED (+) lead to the POSITIVE (+) post
of the driver's side battery. Connect the
BLACK (-) lead to the NEGATIVE (-) post
of the same battery.
Figure 44
6-6.
Route the wiring harness to the AirDog®
and connect the 2 pin Deutsch connector
to the corresponding connector on
the AirDog®.
Figure 45
19
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
Initial Startup Procedures
Section 7
INITIAL START PROCEDURE
The AirDog® is a self priming system, however, to prevent potential damage and reduce the life
expectancy of the system, it is recommended to pre-fill only the water separator with diesel fuel
before initial startup.
7-1.
Pre-fill the water separator with diesel fuel.
7-2.
Turn the starter key to the on/run position.
7-3.
While the AirDog® is operating, bleed the fuel line to the engine of air by loosening the
fuel line connection at the engine fitting. As soon as the line is purged of air and pure
fuel is observed, properly tighten the fuel fitting. NOTE: put a rag or shop towel over
and around fitting to prevent splatter. Catch all spilled fuel and dispose of properly.
7-4.
Start engine!
RECHECK ALL FUEL FITTINGS FOR LEAKAGE AND PROPERLY TORQUE. BE
SURE ALL FUEL LINES ARE PROPERLY ROUTED TO PROTECT FROM
EXCESSIVE HEAT AND SECURED TO PROTECT FROM CHAFFING AND
ABRASION. RECHECK ALL ELECTRICAL LINES, SECURE AS NECESSARY.
Checking Pump Noise!
NOTE: Each AirDog® has been manufactured in a Quality Controlled process and wet tested
for operation and performance before shipment. This is a very quiet and smooth running
system. With fuel or air alone, the AirDog® fuel pump will run very quietly. However, if any
fuel fitting on the vacuum side, between the fuel tank and the AirDog® or the water separator,
has been left loose during the installation process, the system may suck air at an excessive rate
and will be very noisy. To check for this problem, unscrew the water separator 3 or 4 full turns
and activate the AirDog® by turning the ignition switch to on. If the AirDog® runs quietly, then
excessive air from a loose fitting or leaking water separator seal is most likely the reason for the
excessive noise. Correct as necessary.
A.
The seal groove in the 3” filter is a snug fit and on occasion the seal has been found
to not be fully seated. Remove the water separator, remove the seal from the top of
the nut plate. Clean and lubricate the seal grove. Carefully replace the seal in the
grove. Be sure to fully seat the seal.
B.
Check all fittings, especially the quick connect at the tank.
20
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
Fuel Filter & Water Separator
Section 8
Filter Service Recommendations
Plugging of either the fuel filter or the water separator itself will cause low fuel pressure and
low flow to the engine. If a low fuel pressure issue exists, replace the fuel filter.
AirDog®
2 Micron Fuel Filter
AirDog®
WATER
SEPARATOR
Drain Valve
The Water Separator
Replace the water separator every other time you change the Fuel Filter or if it becomes
damaged or plugged. It is suggested to check/drain the water separator every three months or
as needed should you experience excessive ‘water in fuel’ conditions. When installing the water
separator, be sure to clean the underside of the AirDog® base. Follow the instructions printed
on the pre-filter for proper tightening procedures.
CAUTION: Be extremely careful to prevent any contaminates or debris from entering the prefilter when removing it for cleaning! Large debris will jam the Gerotor and cause the fuse to
blow. This is not a warranty item. Should this happen, you can easily put the system back into
working order. See the instructions on “How to clean the Gerotor” for proper procedures.
The Fuel Filter
Remove the fuel filter by turning it counter clockwise. Do Not pre-fill the fuel filter with fuel.
The AirDog® will fill the filter and prime the system automatically. Follow the instructions on
the filter for proper tightening procedures.
CAUTION: Dispose of waste fuel and used filters properly to protect OUR environment!
21
AirDog® FP-100 & FP-150
Ford PowerStroke 2008 6.4L
AirDog® Fuel Pump
Section 9
Cleaning Foreign Debris from the Gearotor Assembly
Step 1
Remove the four (4) button
head cap crews that secure
the gearotor cap.
Step 2
Step 3
Carefully remove the O’ring, Remove and clean the gearotor.
you will need to re-use it.
Be very careful not to damage
the gearotor.
Step 4
Clean the inside of the
gearotor pocket.
Step 5
Replace the O’ring and
center gear.
Step 6
Align the teeth and
install the outer gear.
Step 7
Install the gearotor cap. Be very
careful to index the cap to position
the wide space between the half
moon cuts to the bottom.
Step 8
Replace the cap into
position. Be very careful,
do not pinch the O’ring.
Torque the cap screws.
in an opposing pattern.
1
4
3
22
2
Installing a New Filter
1. Clean the area around the filter head and groove or seal area.
NOTE: Lubricate the seal with oil. Do not use diesel fuel to lubricate the seal.
2. Install a new fuel filter on the filter head. Turn clock-wise until the filter contacts the seal.
Tighten the filter one full turn or follow tightening instructions on filter after contact with
the seal has been made.
NOTE: It is not necessary to pre-fill the fuel filter!
CAUTION: DO NOT OVER TIGHTEN, OVER TIGHTENING CAN DISTORT THREADS
OR DAMAGE THE FILTER SEAL.
3. To prime the filter, turn the ignition switch to the on position. Start the engine.
Water Separator
With the engine turned off, pinch off the suction line. Open valve on the bottom of the water
separator. Drain into a suitable container until all water has been removed. Close valve.
Remove the pinch in the suction.
DRAINING: The water separator should be serviced once a month or when severe water in
fuel conditions require.
NOTE: Collect all spilled fuel and dispose of in accordance with federal, state and local
regulations.
23
PUREFLOW AIRDOG
LIFETIME LIMITED EXPRESS WARRANTY
FOR
Covered PureFlow AirDog I, II and Raptor Systems
IMPORTANT NOTICE
TO ACTIVATE YOUR PURFLOW AIRDOG WARRANTY, YOU MUST COMPLETE AND
MAIL YOUR WARRANTY CARD TO PUREFLOW AIRDOG WITH A COPY OF YOUR
ORIGINAL SALES RECEIPT WITHIN 30 DAYS OF PURCHASE. FAILURE TO
COMPLETE AND SUBMIT YOUR WARRANTY CARD WILL RESULT IN A WARRANTY
PERIOD OF THE COVERED PRODUCE TO ONE (1) YEAR FROM THE DATE OF
PURCHASE.
PureFlow AirDog (hereafter collectively, “SELLER”) warrants and guarantees only to the Original Purchaser
(hereafter collectively, BUYER) that All PureFlow AirDog Systems (hereafter collectively, PRODUCT) shall be
free from defects of materials and workmanship in the manufacturing process for as long as the BUYER owns the
PRODUCT.
The Lifetime Limited Express Warranty is limited to the PRODUCT purchased by the original BUYER of the
PRODUCT and limited solely to the parts contained within the PRODUCT and EXCLUDES ALL ELSE
INCLUDING FILTERS AND WATER SEPARATORS. Any PRODUCT that is in question of Warranty must be
returned, shipped prepaid, to PureFlow AirDog. All Warranty claims are subject to the approval of PureFlow
AirDog. If it is determined that a Warranty claim exists, PureFlow AirDog will, at its sole discretion, replace the
defective PRODUCT with a comparable PRODUCT, repair the defective PRODUCT, or refund the BUYER”S
purchase price in exchange for the PRODUCT. Repairs or replacements are warranted for only the remainder of
the original warranty period and only to the original BUYER.
Under no circumstances shall the SELLER be liable for any labor charged or travel time incurred in the diagnosis
for defects, removal, or reinstallation of the PRODUCT, or any contingent expense.
Under no circumstances will the SELLER be liable for any damage or expense incurred by reason of the use or sale
of the PRODUCT.
Other than expressly set forth herein, the SELLER shall in no way be responsible for the proper or improper use
and service of the PRODUCT. In no event shall the SELLER be liable for any special, incidental, indirect or
consequential damages of any kind or nature, whether or not the BUYER of the PRODUCT was advised of the
possibility of damage or harm, arising or resulting from the use or performance of the PRODUCT and BUYER
hereby waives the right to any and all such claims.
BUYER, acknowledges that he/she is not relying on SELLER’S skill or judgment to select or furnish goods
suitable for any particular purpose and that SELLER has no liability that will extend beyond the scope of the
LIMITED EXPRESS WARRANTY contained herein, and BUYER hereby waives all remedies or liabilities,
expressed or implied, arising by operation of law or otherwise.(including, without limitation, any obligation of
SELLER with respect to fitness for any particular purpose; merchantability; and special, incidental, indirect or
consequential damages) or whether or not occasioned by SELLER’S negligence.
SELLER disclaims any warranty and expressly disclaims any liability for personal inquiry or damages related to
BUYER’S use of the PRODUCT. BUYER acknowledges and agrees that the disclaimer of any liability for
personal injury is a material term for this agreement and BUYER agrees to indemnify SELLER and hold SELLER
harmless from any claim related to the PRODUCT and its use or performance. Under no circumstances will
SELLER be liable for any damages, liabilities, costs or expenses incurred as a result of or by reason of use,
performance or sale of the PRODUCT, including without limitation, any damages, liabilities, costs or expenses
incurred by reason of BUYER’S negligence related to those uses of the PRODUCT.
The proper installation of the PRODUCT is the sole responsibility of the BUYER. The SELLER assumes no
liability regarding improper installation or misapplication of the PRODUCT.
24
SELLER hereby provides the following limited warranty as to description, quality, merchantability, fitness for the
PRODUCT’S purpose, productiveness, or any other matter of SELLER’S PRODUCT sold herewith. The
SELLER shall be in no way responsible for the open use and service of the PRODUCT and the BUYER hereby
waives all rights other than those expressly written herein. This Warranty shall not be extended or varied except
by a written instrument signed by SELLER and BUYER.
IN THE EVENT THAT THE BUYER DOES NOT AGREE WITH THIS AGREEMENT, THE BUYER MAY
PROMPTLY RETURN THE PRODUCT, IN A NEW AND UNUSED CONDITION, WITH A DATED PROOF
OF PURCHASE, TO THE PLACE OF PURCHASE WITHIN THIRTY (30) DAYS FROM THE DATE OF
PURCHASE FOR A FULL REFUND. THE BUYER AGREES THAT THE INSTALLATION OF THIS
PRODUCT CONFIRMS THE BUYER HAS READ AND UNDERSTANDS THIS AGREEMENT AND
ACCEPTS THE TERMS AND CONDITIONS OF THIS AGREEMENT.
Warranty Procedure
In the unlikely event a warranty appears as if it may be warranted, the following steps are taken:
1 The customer discussed the symptoms of the problem with a PureFlow AirDog Technician. The
customer is to have the system Serial Number and Model Number available for the Technician
when the call is made. This will expedite all steps of the process.
2 The customer performs any and all tests requested by the PureFlow AirDog Technician. This is done to
isolate the potential problem while eliminating potential installation or maintenance related issues,
3 If the PureFlow AirDog Technician determines based on the customer feedback concerning the
requested testing that system may be at fault, the customer is advised that all returned pumps are
tested upon arrival and should this returned pump perform at design criteria upon arrival, the
customer will be charged a $50.00 fee.
4 The PureFlow AirDog Technician will first request the customer’s phone number in the event the phone
call is accidentally disconnected and then transfer the customer to a PureFlow AirDog Customer
Service Representative. Should a Customer Service Representative not be available, the Technician
will offer the Customer the option to hold, call back, or receive a return call.
5 The PureFlow AirDog Customer Service Representative will check to determine if the customer’s
Warranty Registration Card is on file.
a. If no Warranty Registration is found, the customer will be required to supply the original
purchase receipt showing the purchase date.
b. If no Warranty Registration is found, the customer will be advised of the options should the
system in question is out of the default warranty period (1 year).
6 The PureFlow AirDog Customer Service Representative will request the customer information,
including: Name, Address, Phone Number, Model Number, Serial Number, Year / Make / Model of
vehicle, Name of Dealer purchased from, Purchase Date, Description of Problem, Customers’
understanding of the resolution, and customer credit card information.
7 PureFlow AirDog will cover Ground Shipping charges to ship the replacement unit and will include a
prepaid shipping label for the return of the defective unit. Any additional items ordered at the
time of the replacement shipment will include their portion of the shipping cost.
8 A period of 15 Calendar Days from the time of shipment is provided for the receipt of the defective unit
at the PureFlow AirDog facility. Failure to return ship the defective unit to arrive within the defined
time period will result in a charge of $250.00 against the customer’s credit card as the purchase
cost of the defective unit.
Copyright © 2009
PureFlow AirDog
All Right Reserved
PFT Bulletin No. ADI-F-08P-100/150
Printed 10
Revised July 24, 2014
25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement