AL624E - Linear Power Supply / Charger Overview:

AL624E - Linear Power Supply / Charger Overview:
AL624E - Linear Power Supply / Charger
Overview:
The AL624E Linear Power Supply / Charger will convert a low voltage AC input to a low voltage DC output.
This general purpose power supply has a wide range of applications for access control, security and CCTV system
accessories that require additional power.
Specifications:
Input:
• Input 16VAC to 24VAC, 20VA to 40VA (Voltage Output/Transformer Selection Table)
Output:
• Switch selectable 6VDC-12VDC-24VDC.
• 1.2 amp continuous supply current at 6VDC-12VDC.
• 750mA continuous supply current at 24VDC.
• Filtered and electronically regulated output.
Battery Backup:
• Built-in charger for sealed lead acid or gel type batteries.
• Maximum charge current 300mA.
• Automatic switchover to stand-by battery when AC Fails.
• PTC battery protection.
Additional Features:
• Thermal and short circuit protection with auto reset.
• AC input and DC output LED indicators. • Extremely compact design.
• Includes battery leads and enclosure.
Enclosure Dimensions: 8.5”H x 7.5” W x 3.5” D
Voltage Output/Transformer Selection Table:
Output
Voltage Selector (JMPR)
Transformer
6VDC @1.2 amp continuous supply current
Cut Jumper J2 Only
12VAC / 20 VA (Altronix model TP1220)
12VDC @ 1.2 amp continuous supply current
Leave J1 & J2 Intact
16.5VAC / 20 VA (Altronix model TP1620)
24VDC @ 750mA continuous supply current
Cut Jumper J1 Only
24VAC / 40 VA (Altronix model TP2440)
Installation Instructions:
1. Mount AL624 into enclosure (Fig. 1, pg. 2).
2. Mount AL624E in desired location.
3. Unit is factory set for 12VDC. For 6VDC output cut jumper J2, for 24VDC output cut Jumper J1.
4. Connect proper transformer to terminals marked [AC] (Voltage Output/Transformer Selection Table).
Use 18 AWG or larger for all power connections (Battery, DC output).
5. Measure output voltage before connecting devices. This helps avoid potential damage.
6. Devices to be powered should be connected to terminals marked [+ DC] and [DC - BAT] carefully observing polarity.
7. Connect battery to terminals marked [BAT +] and [DC - NEG] (battery leads included)
Note: When batteries are not used, a loss of AC will result in a loss of output voltage.
LED Diagnostics:
Red (DC)
Green (AC) Power Supply Status
ON
ON
Normal operating condition.
ON
OFF
Loss of AC, Stand-by battery supplying power.
OFF
ON
No DC output. Short circuit or thermal overload condition.
OFF
OFF
No DC output. Loss of AC. Discharged or no battery present.
Terminal Identification:
Terminal Legend
Function/Description
AC/AC
Low voltage AC input (Voltage Output/Transformer Selection Table, pg.1).
- DC +
6VDC or 12VDC @ 1.2 amp continuous supply current.
+ BAT -
Stand-by battery connections. Maximum charge rate 300mA.
Fig. 1
FACTORY SET AT 12V
CUT J1 FOR 24V
CUT J2 FOR 6V
J1
J2
STEP 1:
Use these holes to mount
AL624 by pushing the nylon
circuit board fasteners (Fig. 1A)
through the back of the enclosure.
Nylon fasteners will snap into place.
DC
AC
AC AC
+DC - BAT +
STEP 2: Mount AL624 circuit board to nylon fasteners
by pressing down circuit board onto nylon fasteners.
Note: Springlock on fasteners is used to remove AL624 circuit board.
Note: Four (4) fasteners are provided in the AL624 carton.
Springlock
Fig. 1a
Nylon Fastener
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
website: www.altronix.com, e-mail: [email protected], Lifetime Warranty, Made in U.S.A.
IIAL624E - Rev. 091211 I12K
MEMBER
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement